Experimental techniques

2.1 Measurement
Apparatus used in the lab:
Name
Beaker

Use
Used to hold liquids

Burette

Used to add accurate

volumes of liquid

Conical Flask

Used to hold liquids

Crystallizing dish

Holds solutions
evapourating into
crystals

Picture

Flat bottomed flask

Used to hold liquids

which dont require
heating

Filter funnel

Used to separate
solids from liquids

Condenser

Used to condense
vapours

Measuring cylinder

Used to measure
approximate volumes
of a liquid

Clock

Used to measure time

in experiments

Pipette

Used to dispense an
accurate volume of
liquid, can measure
volumes of 10ml to
25ml

Round bottomed
flask

Used for heating

liquids evenly

Spatula

Used to handle small

amounts of a solid

Tap funnel

Used to add a
controlled volume of
a liquid

Tripod

Used as a stand for

flasks and beakers
during heating

Test tube

Used to hold liquids

while being mixed.

Boiling tube

Used to hold liquids

while it is being
heated.

Dropping Pipette

Used to collect a
small amount of
liquid and drop the
collect liquid as drops.

Gas syringe

Used to collect gases

emitted from
reactions. Can also
measure the volume
of gas collected.

Digital Balance

Used to measure the

mass of solids or
liquids in grams or
kilograms

2.2
(a) Criteria of purity
Chromatography:
Chromatography is used to separate several substances dissolved in a solution. A drop of
the solution is placed on the origin line at the bottom of a chromatography paper.

The different solutes in the solution move up the paper with the solvent, but at different
speeds. A solute, which is very soluble in the solvent, travels through the paper faster than
a solute, which is only slightly soluble.
When the solvent reaches the top of the paper, the process is stopped. Different solutes
will have traveled different distances. The result is a chromatogram.
Chromatography is only suitable for separating very small quantities. It is not only used to
determine what a mixture consists of, but it is also used as a purity test. A single pure
substance will produce only one spot.
Chromatography was originally devised to separate coloured substances in solution. It can
also be used to separate colourless substances, which can be seen by spraying the filter
paper by a suitable chemical called a locating agent, which colours the spots produced.
A chromatogram can be made of some known pure substances and one unknown. The
positions of the different components of the unknown substance can be compared to those

of the known substances. The figure below shows how results can be obtained by this
method.

Testing for purity:

Testing for purity of many substances such as foodstuffs and drugs can be carried by either
one of two methods:
1. By making a chromatogram for the substance. A single pure substance will produce only
one spot.
2. By measuring the melting point or the boiling point of the substance. Pure substances
have their own fixed melting & boiling points.
(b) Methods of purification
1) Filtration:
This method is used to separate:
- A solid from a liquid
- An insoluble solid from a soluble one. The soluble solid is dissolved and can be
removed by evapouration

Filtration is carried out by pouring the mixture through the filter paper. The liquid that goes
through is called the filtrate; the solid that remains behind is the residue. To obtain the
pure sample of the soluble solid the filtrate is evapourated.
Decantation
It is an alternative method in which the solid is left to settle. Then the liquid is poured
leaving the solid behind.

2) Evapouration:
This evapouration is used to recover a solute form its solution. For example, to recover NaCl
from sea water, sea water is boiled so that water is released as a vapour and NaCl is left in
the evapourating basin.

The solution is boiled so that the liquid is released as a gas and the solid is left in the
evapourating basin.
Crystallization
It is an alternative method to recover a solute from its solution. The solution is evapourated
to the crystallization point, i.e. the point at which crystals of the solute will form on cooling,
which can filtered out, washed and dried.

3) Distillation
This method is used to recover a solvent from a solution e.g. getting pure water from sea
water. Distillation involves boiling followed by condensation. When the flask is heated the
solution boils and steam passes into the condenser where it is cooled by cold water passing
through the outer condenser tube. The steam condenses and the distillate (distilled water)
collects in the receiver. The salts (impurities) are left in the flask.

4) Sublimation:
Sublimation is used to separate a mixture of two substances where only one of the two
substances sublimes.
For example, if a mixture- of ammonium chloride and sodium chloride is heated, the
ammonium chloride turns directly to vapour (sublimes) but the sodium chloride remains
unchanged. When the vapour is cooled, solid ammonium chloride collects free from sodium
chloride.

5) Fractional distillation:
This method is used to separate a mixture of miscible liquids with different boiling points.
e.g. a mixture of ethanol (78C) and water (100C).

The mixture in the flask is heated so that it boils. Both ethanol vapour and water vapour go
up the fractionating column until the vapour of water (the liquid with higher boiling point
100C) condenses in the fractionating column and drips back into the flask, while the
vapour of alcohol (the liquid with lower boiling point 78C) reaches the top of the column
and distils over and is collected first.
Important applications of fractional distillation
a. The separation of liquid air into oxygen and nitrogen.
b. The separation of crude oil (petroleum) into useful fractions.
c. The separation of fermented liquor into alcohol and water.

If the liquids are immiscible (such as a mixture of oil and water) they can be separated using
a tap funnel.