Scribd
Upload
762 views

General Notes For Civil Engineering

This document provides general notes for civil engineering projects. It specifies that electrical conduits shall not run in columns, excavation for basements over 3m should be stepped, and any backfilling must be compacted in layers not exceeding 200mm or 300mm. Reinforcement bars must be free of contaminants and properly supported with spacers. Cement used shall be grade 43 or 53 ordinary Portland cement meeting relevant standards, and must be stored in a dry, raised area protected from moisture. Water used shall meet quality standards, and concrete cube tests are required at 7 and 28 days to verify compressive strength meets specifications.

Uploaded by

Rachel Ingram
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
762 views

General Notes For Civil Engineering

This document provides general notes for civil engineering projects. It specifies that electrical conduits shall not run in columns, excavation for basements over 3m should be stepped, and any backfilling must be compacted in layers not exceeding 200mm or 300mm. Reinforcement bars must be free of contaminants and properly supported with spacers. Cement used shall be grade 43 or 53 ordinary Portland cement meeting relevant standards, and must be stored in a dry, raised area protected from moisture. Water used shall meet quality standards, and concrete cube tests are required at 7 and 28 days to verify compressive strength meets specifications.

Uploaded by

Rachel Ingram
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

General Notes for civil Engineering

1. Electrical conduits shall not run in column.


2. Earth work excavation for basement above 3 m should be stepped form.
3. Any Back filling shall be compacted 95% of dry density at the optimum
moisture content and in layers not more than 200mm for filling above
structure and 300 mm for no structure
4. F SOLING IS SPECIFIED THE SOLING STONES SHALL BE LAID AT 45 TO 60
INCLINATION (AND NOT VERTICAL) WITH INTERSTICES FILLED WITH SAND OR
MOORUM.
5. Y REPRESENTS TOR STEEL GRADE - Fe-415 OF IS:1786. WITH
CHARECTERISTIC YIELD STRENGTH OF 415 N/MM MINIMUM.
6. REPRESENTS MILD STEEL GRADE - 1 OF IS:432 (PART-1)
7. ALL REINFORCEMENT SHALL BE FREE FROM MILL SCALES, LOOSE RUST &
COATS OF PAINTS, OIL OR ANY OTHER SUBSTANCES.
8. BY PROVIDING PROPER COVER BLOCKS, SPACERS, CHAIRS ETC.. ALL
REINFORCEMENT SHALL BE PLACED AND MAINTAINED IN POSITION AS
SHOWN IN STRUCTURAL DRAWING
9. CEMENT SHALL BE 43 GRADE ORDINARY PORTLAND CEMENT CONFORMING
TO IS:8112 OR53 GRADE ORDINARY
10.PORTLAND CEMENT CONFORMING TO IS:12269-1987.
11.CEMENT SHALL BE STORED IN DRY PLACES ON A RAISED PLATFORM ABOUT
200mm ABOVE FLOOR LEVEL AND
12.300mm
13.AWAY FROM WALLS. BAGS TO BE STACKED NOT MORE THAN 10 BAGS HIGH IN
SUCH A MANNER THAT IT IS
14.ADEQUATELY PROTECTED FROM MOISTURE AND CONTAMINATION.
15.WATER USED FOR BOTH MIXING AND CURING SHALL BE CLEAN AND FREE
FROM INJURIOUS AMOUNTS OF OILS,
16.ACIDS, ALKALIS, SALTS, SUGAR AND ORGANIC MATERIALS OR OTHER
SUBSTANCES THAT MAY BE DELETERIOUS
17.TO CONCRETE OR STEEL. THE pH SHALL BE GENERALLY BETWEEN 6 AND 8.
18.CEMENT SHALL BE TESTED FOR ITS SETTING.
1. THE INITIAL SETTING TIME SHALL NOT BE LESS THAN 30 MINUTES.
2. THE FINAL SETTING TIME SHALL NOT BE MORE THAN 10 HOURS.SAMPLES
FROM FRESH CONCRETE SHALL BE
19.TAKEN AND AT LEAST A SET OF 6 CUBES OF 150mm SHALL BE PREPARED
AND CURED.
3. CUBES EACH AT 7 DAYS AND 28 DAYS SHALL BE TESTED FOR COMPRESSIVE
STRENGTH. THE TEST RESULTS
20.SHOULD BE SUBMITTED TO ENGINEER FORAPPROVAL. IF RESULTS ARE
UNSATISFACTORY NECESSARY
21.ACTION/RECTIFICATION/REMEDIAL MEASURES HAS TO BE EXERCISED.
22.A SET OF CUBE TESTS SHALL BE CARRIED OUT FOR EACH 30 Cum OF
CONCRETE / EACH LEVELS OF CASTING / EACH

You might also like