Scribd
Upload
32 views2 pages

Single Phase 20150209171147194

This document summarizes the design specifications for a single phase heat exchanger. The heat exchanger transfers 30 kW of heat from water at 50C to R407C liquid at -1C. It has a total heat transfer area of 2.32 square meters and operates at a maximum pressure of 155.7 kPa. The heat exchanger is made up of 19 plates that are 287mm long, 117mm wide, and 6mm thick.

Uploaded by

zlajavi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
32 views2 pages

Single Phase 20150209171147194

This document summarizes the design specifications for a single phase heat exchanger. The heat exchanger transfers 30 kW of heat from water at 50C to R407C liquid at -1C. It has a total heat transfer area of 2.32 square meters and operates at a maximum pressure of 155.7 kPa. The heat exchanger is made up of 19 plates that are 287mm long, 117mm wide, and 6mm thick.

Uploaded by

zlajavi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

SSP G7

(v 7.0.3.35)

SINGLE PHASE - Design


Heat Exchanger : B12Lx85/2P
Fluid Side 1 :
Fluid Side 2 :

Water
R407C (Liquid)

Flow Type

Counter-Current

DUTY REQUIREMENTS
Heat load
Inlet temperature
Outlet temperature
Flow rate
Max. pressure drop
Thermal length
PLATE HEAT EXCHANGER
Total heat transfer area
Heat flux
Mean temperature difference
O.H.T.C. (available/required)
Pressure drop -total*
- in ports
Port diameter
Number of channels
Number of plates
Oversurfacing
Fouling factor
Reynolds number
Port velocity
PHYSICAL PROPERTIES
Reference temperature
Dynamic viscosity
Dynamic viscosity - wall
Density
Heat capacity
Thermal conductivity
Min. fluid temperature at wall
Max. fluid temperature at wall
Film coefficient
Minimum wall temperature
Channel velocity
Shear stress

Side 1
kW
C
C
kg/s
kPa

Side 2
30.00

50.00
5.00
0.1595
50.0
2.259

-1.00
3.00
5.284
50.0
0.201

Side 1
m
kW/m
K
W/m,C
kPa
kPa
mm

0.200
0.0166
33.0
21L

C
cP
cP
kg/m
kJ/kg,C
W/m,C
C
C
W/m,C
C
m/s
Pa

SWEP International AB
Address :Box 105, SE-261 22 Landskrona, Sweden www.swep.net

50.3
15.1
33.0
21L
85
39
0.428

%
m,C/kW
m/s

Side 2
2.32
12.9
19.92
923/662

155.7
0.188

21360
5.01

Side 1
26.37
0.842
1.32
996.4
4.179
0.6113
0.97

Side 2
0.90
0.208
0.189
1232
1.419
0.09576
17.51
2990
9.03
0.903
75.2

1370
9.54
0.0337
0.391

Date
2015-02-09

Page
1(2)

SSP G7
(v 7.0.3.35)
Totals
Total weight empty
Total weight filled
Hold-up volume, inner circuit
Hold-up volume, outer circuit
PortSize F1/P1
PortSize F2/P2
PortSize F3/P3
PortSize F4/P4
NND F1/P1
NND F2/P2
NND F3/P3
NND F4/P4
Carbon Footprint

Side 1
kg
kg
dm
dm
mm
mm
mm
mm
mm
mm
mm
mm
kg

Side 2
11.6
17.5
2.65
2.65
33.0
33.0
33.0
33.0
36.0
36.0
36.0
36.0
81.8

DIMENSIONS
A
B
C
D
E
F
G
R

mm
mm
mm
mm
mm
mm
mm
mm

287 +/-2
117 +/-1
234 +/-1
63 +/-1
27 (opt. 45) +/-1
203.30 +0.5%/-1.5%
6 +/-1
22

Disclaimer: Data used in this calculation is subject to change without notice. Calculation is intended to show thermal and hydraulic performance, no
consideration has been taken to mechanical strength of the product. Product restrictions - such as pressure, temperatures and corrosion resistancecan be found in SWEP product sheets and other technical documentation. SWEP may have patents, trademarks, copyrights or other intellectual
property rights covering subject matter in this document. Except as expressly provided in any written license agreement from SWEP, the furnishing of
this document does not give you any license to these patents, trademarks, copyrights, or other intellectual property.
*Excluding pressure drop in connections.

SWEP International AB
Address :Box 105, SE-261 22 Landskrona, Sweden www.swep.net

Date
2015-02-09

Page
2(2)

You might also like