CCNA Semester 2 final exam latest version

1
Which two components are used to determine the router ID in the
configuration of the OSPF routing process? (Choose two.)
the IP address of the first FastEthernet interface
the highest IP address of any logical interface
(true answer)the highest IP address of any physical interface
the default gateway IP address
(true answer)the priority value of 1 on any physical interface

2
Refer to the exhibit. R2 is configured correctly. The network administrator
has configured R1 as shown. Which two facts are true about the forwarding
of route information by R1? (Choose two.)
(true answer)R1 will forward the route information for subnet
192.168.100.0/30. (true answer) R1 will not forward route information
for subnet 192.168.100.4/30.
R1 will forward the route information with an administrative distance set to
50.
R1 will forward the summarized route information for network
192.168.100.0/24.
R1 will forward route information for subnet 10.10.10.0/30 out the serial
interface.

3
Refer to the exhibit. Which two statements are true based on the exhibited
output? (Choose two.)
(true answer)All routes are stable.
Each route has one feasible successor.
The serial interface between the two routers is down.
The administrative distance of EIGRP has been set to 50.
(true answer)The show ip eigrp topology command has been run on
R1.
4
A router has learned two equal cost paths to a remote network via the EIGRP
and RIP protocols. Both protocols are using their default configurations.
Which path to the remote network will be installed in the routing table?
(true answer)the path learned via EIGRP
the path learned via RIP
the path with the highest metric value
both paths with load balancing

5
Refer to the exhibit. Routers R1 and R3 use different routing protocols with
default administrative distance values. All devices are properly configured
and the destination network is advertised by both protocols. Which path will
be used to transmit the data packets from PC1 to PC2?
(true answer)The packets will travel via R2-R1.
The packets will travel via R2-R3.
The traffic will be load-balanced between two paths via R2-R1 and via R2-R3.
The packets will travel via R2-R3, and the other path via R2-R1 will be
retained as the backup path.

6
Which statement is true about the RIPv1 protocol?
It is a link-state routing protocol.
(true answer)It excludes subnet information from the routing
updates.
It uses the DUAL algorithm to insert backup routes into the topology table.
It uses classless routing as the default method on the router.

7
What is the function of the OSPF LSR packet?
It is used to confirm the receipt of LSUs.
It is used to establish and maintain adjacency with other OSPF routers.
(true answer)It is used by the receiving routers to request more
information about any entry in the DBD.
It is used to check the database synchronization between routers
8
Refer to the exhibit. A network administrator is accessing router R1 from the
console port. Once the administrator is connected to the router, which
password should the administrator enter at the R1> prompt to access the
privileged EXEC mode?
Cisco001
Cisco123
(true answer)Cisco789
Cisco901

9
Which two technologies can be used in distance vector routing protocols to
prevent routing loops? (Choose two.)
authentication
link-state advertisements
(true answer)hold-down timers
Spanning Tree Protocol
(true answer)split horizon

10
Refer to the exhibit. An administrator is adding a new subnet of 50 hosts to
R3. Which subnet address should be used for the new subnet that provides
enough addresses while wasting a minimum of addresses?

192.168.1.0/24
192.168.1.48 /28
192.168.1.32/27
(true answer)192.168.1.64/26

11
Refer to the exhibit. Host A is unable to access the Internet. What is the
reason for this?
(true answer)192.168.1.64/26
The IP address of host A is incorrect.
The default gateway of host A is incorrect.
(true answer)The Fa0/1 interfaces of the two routers are configured
for different subnets.
The subnet mask for the Fa0/0 interface of R1 is incorrect.

12
A network administrator uses the RIP routing protocol to implement routing
within an autonomous system. What are two characteristics of this protocol?
(Choose two.)
(true answer)It uses the Bellman-Ford algorithm to determine the
best path.
It displays an actual map of the network topology.
It offers rapid convergence in large networks.
(true answer)It periodically sends complete routing tables to all
connected devices.
It is beneficial in complex and hierarchically designed networks.

13
Refer to the exhibit. What is the meaning of the highlighted value 2?
It is the administrative distance of the routing protocol.
(true answer)It is the number of hops between R2 and the
192.168.8.0/24 network.
It is the value used by the DUAL algorithm to determine the bandwidth for
the link.
It is the convergence time measured in seconds.

14
Refer to the exhibit. Packets destined to which two networks will require the
router to perform a recursive lookup? (Choose two.)
(true answer)10.0.0.0/8
64.100.0.0/16
128.107.0.0/16
172.16.40.0/24
192.168.1.0/24
(true answer)192.168.2.0/24

15
Refer to the exhibit. The 10.4.0.0 network fails. What mechanism prevents
R2 from receiving false update information regarding the 10.4.0.0 network?
(true answer)split horizon
hold-down timers
route poisoning
triggered updates

16
Refer to the exhibit. The routers are properly configured using a dynamic
routing protocol with default settings, and the network is fully converged.
Router A is forwarding data to router E. Which statement is true about the
routing path?
(true answer)If the network uses the RIP protocol, router A will
determine that all paths have equal cost.
If the network uses the RIP protocol, router A will update only the A-C-E path
in its routing table.
If the network uses the EIGRP routing protocol, router A will determine that
path A-D-E has the lowest cost.
If both RIP and EIGRP protocols are configured on router A, the router will
use the route information that is
learned by the RIP routing protocol.

17
Refer to the exhibit. All routers are running the same routing protocol. Based
on the exhibit and its displayed commands, which statement is true?
The wildcard mask is incorrectly configured.
A default route must be configured on every router.
Routers B, C, and D have no access to the Internet.
(true answer)The link to the ISP is not advertised by the routing
protocol process.

18
Refer to the exhibit. A ping between host A and host B is successful, but
pings from host A to operational hosts on the Internet fail. What is the
reason for this problem?
The FastEthernet interface of R1 is disabled.
(true answer)One of the default routes is configured incorrectly.
A routing protocol is not configured on both routers.
The default gateway has not been configured on host A.

19
Refer to the exhibit. While trying to diagnose a routing problem in the
network, the network administrator runs the debug ip rip command. What
can be determined from the output of this command?
The router is broadcasting RIP updates.
The router will be unable to ping 192.168.1.2.
The router is directly connected to network 172.16.1.0 /24.
(true answer)The router has two interfaces that participate in the RIP
process.

20
A router boots and enters setup mode. What is the reason for this?
The IOS image is corrupt.
Cisco IOS is missing from flash memory.
(true answer)The configuration file is missing from NVRAM.
The POST process has detected hardware failure.

21
Refer to the exhibit. Which three statements are true of the routing table for
Router1? (Choose three.)
The route to network 172.16.0.0 has an AD of 156160.
Network 192.168.0.16 can best be reached using FastEthernet0/0.
(true answer)The AD of EIGRP routes has been manually changed to a
value other than the default value.
(true answer)Router1 is running both the EIGRP and OSPF routing
process. (true answer) Network 172.17.0.0 can only be reached using
a default route. (true answer)
(true answer)No default route has been configured.

22
A network administrator has enabled RIP on routers B and C in the network
diagram. Which of the following commands will prevent RIP updates from
being sent to Router A?
A(config)# router rip
A(config-router)# passive-interface S0/0
B(config)# router rip
B(config-router)# network 192.168.25.48
B(config-router)# network 192.168.25.64
A(config)# router rip
A(config-router)# no network 192.168.25.32
(true answer)B(config)# router rip
(true answer)B(config-router)# passive-interface S0/0
(true answer) A(config)# no router rip

23
Refer to the exhibit. The show cdp neighbors command was run at R1. Which
two facts about the newly detected device can be determined from the
output? (Choose two.)
(true answer)ABCD is a router that is connected to R1.
ABCD is a non-CISCO device that is connected to R1.
(true answer)The device is connected at the Serial0/0/1 interface of
R1.
R1 is connected at the S0/0/1 interface of device ABCD.
ABCD does not support switching capability.

24
Which statement is true about the metrics used by routing protocols?
(true answer)A metric is a value used by a particular routing protocol
to compare paths to remote networks.
(true answer) A common metric is used by all routing protocols.
The metric with the highest value is installed in the routing table.
The router may use only one parameter at a time to calculate the metric.

25
Refer to the exhibit. What action will R2 take for a packet that is destined for
192.168.2.0?
It will drop the packet.
It will forward the packet via the S0/0/0 interface.
It will forward the packet via the Fa0/0 interface.
(true answer)It will forward the packet to R1.

26
Which two router component and operation pair are correctly described?
(Choose two.)
DRAM - loads the bootstrap
RAM - stores the operating system
Flash - executes diagnostics at bootup
(true answer)NVRAM - stores the configuration file
ROM - stores the backup configuration file
(true answer)POST - runs diagnostics on hardware modules

27
Which two statements are true about the EIGRP successor route? (Choose
two.)
It is saved in the topology table for use if the primary route fails.
(true answer)It may be backed up by a feasible successor route. (true
answer)
(true answer)It is used by EIGRP to forward traffic to the destination.
It is flagged as active in the routing table.
After the discovery process has occurred, the successor route is stored in the
neighbor table.

28
Refer to the exhibit. Which two facts can be derived from this output?
(Choose two.)
(true answer)Three network devices are directly connected to
Router2.
(true answer) The serial interface between Router2 and Router3 is
up.
Router1 and Router3 are directly connected.
Six devices are up and running on the network.
Layer 3 functionality between routers is configured properly.

29
In a lab test environment, a router has learned about network 172.16.1.0
through four different dynamic routing processes. Which route will be used
to reach this network?
(true answer)D 172.16.1.0/24 [90/2195456] via 192.168.200.1,
00:00:09, Serial0/0/0
O 172.16.1.0/24 [110/1012] via 192.168.200.1, 00:00:22, Serial0/0/0
R 172.16.1.0/24 [120/1] via 192.168.200.1, 00:00:17, Serial0/0/0
I 172.16.1.0/24 [100/1192] via 192.168.200.1, 00:00:09, Serial0/0/0

30
Which three statements are true regarding the encapsulation and de-
encapsulation of packets when traveling through a router? (Choose three.)
(true answer)The router modifies the TTL field, decrementing it by
one.
The router changes the source IP to the IP of the exit interface.
(true answer)The router maintains the same source and destination
IP.
(true answer) The router changes the source physical address to the
physical address of the exit interface.
The router changes the destination IP to the IP of the exit interface.
The router sends the packet out all other interfaces, besides the one it
entered the router on.

31
Refer to the exhibit. Both routers are using the RIPv2 routing protocol and
static routes are undefined. R1 can ping 192.168.2.1 and 10.1.1.2, but is
unable to ping 192.168.4.1. What is the reason for the ping failure?
The serial interface between two routers is down.
R2 is not forwarding the routing updates.
(true answer)The 192.168.4.0 network is not included in the RIP
configuration of R2.RIPv1 needs to be configured.

32
Refer to the exhibit. Two routers are unable to establish an adjacency. What
is the possible cause for this?
The two routers are connected on a multiaccess network.
(true answer)The hello and dead intervals are different on the two
routers. (true answer) They have different OSPF router IDs.
They have different process IDs.

33
Refer to the exhibit. Routers R1 and R2 are directly connected via their serial
interfaces and are both running the EIGRP routing protocol. R1 and R2 can
ping the directly connected serial interface of their neighbor, but they cannot
form an EIGRP neighbor adjacency. What action should be taken to solve this
problem?
Enable the serial interfaces of both routers.
Configure EIGRP to send periodic updates.
Configure the same hello interval between the routers.
(true answer)Configure both routers with the same EIGRP process ID.

34
Refer to the exhibit. R1 and R2 are unable to establish an adjacency. What
two configuration changes will correct the problem? (Choose two.)
Set a lower priority on R2.
(true answer)Configure the routers in the same area.
Set a lower cost on R2 compared to R1.
Add a backup designated router to the network.
(true answer)Match the hello and dead timers on both routers.

35
Refer to the exhibit. All routers are properly configured to use the EIGRP
routing protocol with default settings, and the network is fully converged.
Which statement correctly describes the path that the traffic will use from
the 10.1.1.0/24 network to the 10.1.2.0/24 network?
It will use the A-D path only.
It will use the path A-D, and the paths A-C-D and A-B-D will be retained as
the backup paths.
It will use all the paths equally in a round-robin fashion.
(true answer)The traffic will be load-balanced between A-B-D and A-C-
D.
36
Refer to the exhibit. Which router is advertising subnet 172.16.1.32/28?
Router1
Router2
Router3
(true answer)Router4

37
Refer to the exhibit. The hosts that are connected to R2 are unable to ping
the hosts that are connected to R1. How can this problem be resolved?
Configure the router ID on both routers.
(true answer)Configure the R2 router interfaces for area 0.
Configure a loopback interface on both routers.
Configure the proper subnet masks on the router interfaces.

38
Refer to the exhibit. The network has three connected routers: R1, R2, and
R3. The routes of all three routers are displayed. All routers are operational
and pings are not blocked on this network. Which ping will fail?
from R1 to 172.16.1.1
(true answer)from R1 to 192.168.3.1
from R2 to 192.168.1.1
from R2 to 192.168.3.1

39
Refer to the exhibit. Router R2 is configured properly and all interfaces are
functional. Router R1 has been installed recently. Host A is unable to ping
host B. Which procedure can resolve this problem?
Configure a static route on R1 using the IP address of the serial interface on
R1.
Configure a default route on R1 with the exit interface Fa0/0 on R1.
(true answer)Configure a static route on R1 using the IP address of
S0/0/0 on R2.
Configure a default route on R1 using the IP address of Fa0/0 on R2.

40
Refer to the exhibit. To implement the RIPv2 protocol, the network
administrator runs the commands as displayed. However, the show ip
protocol command fails to display any output. How can the administrator
solve the problem that is indicated by the lack of output from this command?
Include the default-information originate command.
Include the no auto-summary command.
(true answer)Specify the network for which RIP routing has to be
enabled.
Implement RIPv2 authentication in the network.

41
Refer to the exhibit. A router learns a route to the 192.168.6.0 network, as
shown in the output of the show ip rip database command. However, upon
running the show ip route command, the network administrator sees that the
router has installed a different route to the 192.168.6.0 network learned via
EIGRP. What could be the reason for the missing RIP route?
(true answer)Compared to RIP, EIGRP has a lower administrative
distance.
Compared to EIGRP, RIP has a higher metric value for the route.
Compared to RIP, the EIGRP route has fewer hops.
Compared to RIP, EIGRP has a faster update timer.

42
Refer to the exhibit. A network administrator has configured R1 as shown,
and all interfaces are functioning correctly. A
ping from R1 to 172.16.1.1 fails. What could be the cause of this problem?
The serial interface on R1 is configured incorrectly.
(true answer)The default route is configured incorrectly.
The default-information originate command must be issued on R1.
Autosummarization must be disabled on R1.

43
Refer to the exhibit. A network administrator wants to reduce the size of the
routing table of R1. Which partial routing table entry in R1 represents the
route summary for R2, without including any additional subnets?
10.0.0.0/16 is subnetted, 1 subnets
D 10.5.0.0[90/205891] via 192.168.1.2, S0/0/0
10.0.0.0/24 is subnetted, 4 subnets
D 10.5.0.0[90/205198] via 192.168.1.2, S0/0/0
(true answer)10.0.0.0/22 is subnetted, 1 subnets
(true answer)D 10.5.0.0[90/205901] via 192.168.1.2, S0/0/0
10.0.0.0/8 is subnetted, 4 subnets
D 10.5.0.0[90/205001] via 192.168.1.2, S0/0/0

44
Which two statements are true for link-state routing protocols? (Choose two.)
(true answer)Routers that run a link-state protocol can establish a
complete topology of the network.
Routers in a multipoint network that run a link-state protocol can exchange
routing tables.
Routers use only hop count for routing decisions.
(true answer)The shortest path first algorithm is used.
Split horizon is used to avoid routing loops.

45
Refer to the exhibit. Which two components are required to complete the
configuration? (Choose two.)
a crossover cable
a DCE device
(true answer)a DTE device
a modem
(true answer)a V.35 cable

46

Refer to the exhibit. The output of the show ip route command for router R1
is displayed. What action will the router take
for a packet that is destined for 192.168.1.5?
(true answer)It will drop the packet.
It will forward the packet to interface Serial0/0/0.
It will determine the route for the packet through a routing protocol.
It will forward the packet to the default gateway.

47
Refer to the exhibit. A network administrator has run the show interface
command. The output of this command is displayed. What is the first step
that is required to make this interface operational?
Switch the cable with a known working cable.
(true answer)Issue the no shutdown command on the interface.
Configure the interface as a loopback interface.
Set the encapsulation for the interface.

48
What are two tasks that must be completed before two routers can use OSPF
to form a neighbor adjacency? (Choose two.)
The routers must elect a designated router.
(true answer)The routers must agree on the network type.
(true answer) The routers must use the same dead interval.
The routers must exchange link state requests.
The routers must exchange database description packets.

49
Refer to the exhibit. All interfaces are addressed and functioning correctly.
The network administrator runs the tracert command on host A. Which two
facts could be responsible for the output of this command? (Choose two.)
The gateway for Host A is missing or improperly configured.
The gateway for Host B is missing or improperly configured.
The entry for 192.168.1.0/24 is missing from the routing table of R1.
(true answer)The entry for 192.168.1.0/24 is missing from the routing
table of R2. (true answer)
(true answer)The entry for 192.168.2.0/24 is missing from the routing
table of R1. The entry for 192.168.2.0/24 is missing from the routing table
of R2.

50
Refer to the exhibit. How many routes are ultimate routes?
(true answer)3
4
5
7

51
Refer to the exhibit. Which summarization should R1 use to advertise its
networks to R2?
192.168.1.0/24
192.168.0.0/24
(true answer)192.168.0.0/22
192.168.1.0/22

52
How does route poisoning prevent routing loops?
New routing updates are ignored until the network has converged.
(true answer)Failed routes are advertised with a metric of infinity.
A route is marked as unavailable when its Time to Live is exceeded.
The unreachable route is cleared from the routing table after the invalid
timer expires.

53
What are two functions of a router? (Choose two.)
(true answer)It forwards data packets toward their destination.
It forwards the packet to the destination if the TTL value is 0.
It changes the destination IP address of data packets before forwarding them
to an exit interface.
It determines the best path based on the destination MAC address.
(true answer)It acts as an intersection between multiple IP networks.

54
Which routing protocol maintains a topology table separate from the routing
table?
IGRP
RIPv1
RIPv2
(true answer)EIGRP

55
Refer to the exhibit. All routers are running RIPv1. The two networks
10.1.1.0/29 and 10.1.1.16/29 are unable to access each other. What can be
the cause of this problem?
Because RIPv1 is a classless protocol, it does not support this access.
(true answer)RIPv1 does not support discontiguous networks.
RIPv1 does not support load balancing.
RIPv1 does not support automatic summarization.

56
Which two statements are correct about the split horizon with poison reverse
method of routing loop prevention? (Choose two.)
It is enabled by default on all Cisco IOS implementations.
(true answer)It assigns a value that represents an infinite metric to
the poisoned route.
It sends back the poisoned route update to the same interface from where it
was received.
It instructs routers to hold all changes that might affect routes, for a
specified period of time.
(true answer)It limits the number of hops a packet can traverse
through the network before it is discarded.

57
What are two reasons for the occurrence of a routing loop? (Choose two.)
slow convergence
(true answer)incorrectly configured static routes
routes that are learned via two routing protocols
(true answer)static and dynamic routing being used on the same
router
lack of a default route on the router that connects to the Internet

58
All routers in a network are configured in a single OSPF area with the same
priority value. No loopback interface has been set on any of the routers.
Which secondary value will the routers use to determine the router ID?
The highest MAC address among the active interfaces of the network will be
used.
There will be no router ID until a loopback interface is configured.
The highest IP address among the active FastEthernet interfaces that are
running OSPF will be used.
(true answer)The highest IP address among the active interfaces will
be used.

59
Refer to the exhibit. Although R2 is configured correctly, host A is unable to
access the Internet. What are two static routes that can be configured on R1,
either of which would enable Internet connectivity for host A? (Choose two.)

ip route 0.0.0.0 0.0.0.0 Fa0/0

(true answer)ip route 0.0.0.0 0.0.0.0 Fa0/1
ip route 0.0.0.0 0.0.0.0 10.1.1.1
(true answer)ip route 0.0.0.0 0.0.0.0 10.1.1.2
ip route 209.165.202.0 255.255.255.0 10.1.1.
***********************************************************

Refer to the exhibit. Two routers are unable to establish an adjacency. What
is the possible cause for this?
The two routers are connected on a multiaccess network.
(true answer) The hello and dead intervals are different on the two routers.
They have different OSPF router IDs.
They have different process IDs.

What is the function of the OSPF LSR packet?

It is used to confirm the receipt of LSUs.
It is used to establish and maintain adjacency with other OSPF routers.
(true answer) It is used by the receiving routers to request more information
about any entry in the DBD.
It is used to check the database synchronization between routers.

3
Refer to the exhibit. The hosts that are connected to R2 are unable to ping
the hosts that are connected to R1. How can this problem be resolved?
Configure the router ID on both routers.
(true answer) Configure the R2 router interfaces for area 0.
Configure a loopback interface on both routers.
Configure the proper subnet masks on the router interfaces.

4
Which two statements are true for link-state routing protocols? (Choose two.)
(true answer) Routers that run a link-state protocol can establish a complete
topology of the network.
Routers in a multipoint network that run a link-state protocol can exchange
routing tables.
Routers use only hop count for routing decisions.
(true answer) The shortest path first algorithm is used.
Split horizon is used to avoid routing loops.

5
Refer to the exhibit. Which two statements are true based on the exhibited
output? (Choose two.)
The administrative distance of EIGRP has been set to 50.
(true answer) All routes are stable.
(true answer) The show ip eigrp topology command has been run on R1.
The serial interface between the two routers is down.
Each route has one feasible successor.

6
Refer to the exhibit. Which three statements are true of the routing table for
Router1? (Choose three.)
The route to network 172.16.0.0 has an AD of 156160.
Network 192.168.0.16 can best be reached using FastEthernet0/0.
(true answer) The AD of EIGRP routes has been manually changed to a
value other than the default value.
(true answer) Router1 is running both the EIGRP and OSPF routing process.
Network 172.17.0.0 can only be reached using a default route.
(true answer) No default route has been configured.

7
Which two router component and operation pair are correctly described?
(Choose two.)
DRAM - loads the bootstrap
RAM - stores the operating system
Flash - executes diagnostics at bootup
(true answer) NVRAM - stores the configuration file
ROM - stores the backup configuration file
(true answer) POST - runs diagnostics on hardware modules

8
What are two tasks that must be completed before two routers can use OSPF
to form a neighbor adjacency? (Choose two.)
The routers must elect a designated router.
(true answer) The routers must agree on the network type.
(true answer) The routers must use the same dead interval.
The routers must exchange link state requests.
The routers must exchange database description packets.

9
What are two functions of a router? (Choose two.)
(true answer) It forwards data packets toward their destination.
It forwards the packet to the destination if the TTL value is 0.
It changes the destination IP address of data packets before forwarding them
to an exit interface.
It determines the best path based on the destination MAC address.
(true answer) It acts as an intersection between multiple IP networks.

10
Refer to the exhibit. Which statement is true about router R2?
The routing table content indicates that interface S0/0/0 is administratively
down.
The route for 172.16.1.0 is a static route.
A packet that is destined for a host on the 172.16.3.0 network is forwarded
without performing a routing table lookup.
(true answer) The packets that are routed to network 172.16.1.0 require two
routing table lookups.

11
Refer to the exhibit. The output of the show ip route command for router R1
is displayed. What action will the router take for a packet that is destined for
192.168.1.5?
It will drop the packet.
It will forward the packet to interface Serial0/0/0.
It will determine the route for the packet through a routing protocol.
(true answer) It will forward the packet to the default gateway.

12
Refer to the exhibit. Although R2 is configured correctly, host A is unable to
access the Internet. Which two static routes can be configured on R1 to
enable Internet connectivity for host A? (Choose two.)
ip route 0.0.0.0 0.0.0.0 Fa0/0
(true answer) ip route 0.0.0.0 0.0.0.0 Fa0/1
ip route 0.0.0.0 0.0.0.0 10.1.1.1
(true answer) ip route 0.0.0.0 0.0.0.0 10.1.1.2
ip route 209.165.202.0 255.255.255.0 10.1.1.1
ip route 209.165.202.0 255.255.255.0 10.1.1.2

13
Refer to the exhibit. Which two facts can be derived from this output?
(Choose two.)
(true answer) Three network devices are directly connected to Router2.
(true answer) The serial interface between Router2 and Router3 is up.
Router1 and Router3 are directly connected.
Six devices are up and running on the network.
Layer 3 functionality between routers is configured properly.

14
Refer to the exhibit. Routers R1 and R3 use different routing protocols with
default administrative distance values. All devices are properly configured
and the destination network is advertised by both protocols.
Which path will be used to transmit the data packets between PC1 and PC2?
(true answer) The packets will travel via R2-R1.
The packets will travel via R2-R3.
The traffic will be load-balanced between two paths — via R2-R1 and via R2-
R3.
The packets will travel via R2-R3, and the other path via R2-R1 will be
retained as the backup path.

15
A network administrator uses the RIP routing protocol to implement routing
within an autonomous system. What are two characteristics of this protocol?
(Choose two.)
(true answer) It uses the Bellman-Ford algorithm to determine the best
path.
It displays an actual map of the network topology.
It offers rapid convergence in large networks.
(true answer) It periodically sends complete routing tables to all connected
devices.
It is beneficial in complex and hierarchically designed networks.

16
Refer to the exhibit. What is the meaning of the highlighted value 2?
It is the administrative distance of the routing protocol.
(true answer) It is the number of hops between R2 and the 192.168.8.0/24
network.
It is the value used by the DUAL algorithm to determine the bandwidth for
the link.
It is the convergence time measured in seconds.

17
In a lab test environment, a router has learned about network 172.16.1.0
through four different dynamic routing processes. Which route will be used
to reach this network?
(true answer) D 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09,
Serial0/0/0
O 172.16.1.0/24 [110/1012] via 192.168.200.1, 00:00:22, Serial0/0/0
R 172.16.1.0/24 [120/1] via 192.168.200.1, 00:00:17, Serial0/0/0
I 172.16.1.0/24 [100/1192] via 192.168.200.1, 00:00:09, Serial0/0/0

18
Refer to the exhibit. The routers are properly configured using a dynamic
routing protocol with default settings, and the network is fully converged.
Router A is forwarding data to router E. Which statement is true about the
routing path?
(true answer) If the network uses the RIP protocol, router A will determine
that all paths have equal cost.
If the network uses the RIP protocol, router A will update only the A-C-E path
in its routing table.
If the network uses the EIGRP routing protocol, router A will determine that
path A-D-E has the lowest cost.
If both RIP and EIGRP protocols are configured on router A, the router will
use the route information that is learned by the RIP routing protocol.

19
Which statement is true about the RIPv1 protocol?
It is a link-state routing protocol.
(true answer) It excludes subnet information from the routing updates.
It uses the DUAL algorithm to insert backup routes into the topology table.
It uses classless routing as the default method on the router.

20
Refer to the exhibit. The 10.4.0.0 network fails. What mechanism prevents
R2 from receiving false update information regarding the 10.4.0.0 network?
(true answer) split horizon
hold-down timers
route poisoning
triggered updates

21
Refer to the exhibit. All routers are running RIPv1. The two networks
10.1.1.0/29 and 10.1.1.16/29 are unable to access each other. What can be
the cause of this problem?
Because RIPv1 is a classless protocol, it does not support this access.
(true answer) RIPv1 does not support discontiguous networks.
RIPv1 does not support load balancing.
RIPv1 does not support automatic summarization.

22
How does route poisoning prevent routing loops?
New routing updates are ignored until the network has converged.
(true answer) Failed routes are advertised with a metric of infinity.
A route is marked as unavailable when its Time to Live is exceeded.
The unreachable route is cleared from the routing table after the invalid
timer expires.
23
Which statement is true about the metrics used by routing protocols?
(true answer) A metric is a value used by a particular routing protocol to
compare paths to remote networks.
A common metric is used by all routing protocols.
The metric with the highest value is installed in the routing table.
The router may use only one parameter at a time to calculate the metric.

24
Refer to the exhibit. Both routers are using the RIPv2 routing protocol and
static routes are undefined. R1 can ping 192.168.2.1 and 10.1.1.2, but is
unable to ping 192.168.4.1.
What is the reason for the ping failure?
The serial interface between two routers is down.
R2 is not forwarding the routing updates.
(true answer) The 192.168.4.0 network is not included in the RIP
configuration of R2.
RIPv1 needs to be configured.

25
Refer to the exhibit. A network administrator wants to reduce the size of the
routing table of R1. Which partial routing table entry in R1 represents the
route summary for R2, without including any additional subnets?
10.0.0.0/16 is subnetted, 1 subnets
D 10.5.0.0[90/205891] via 192.168.1.2, S0/0/0
10.0.0.0/24 is subnetted, 4 subnets
D 10.5.0.0[90/205198] via 192.168.1.2, S0/0/0
(true answer) 10.0.0.0/22 is subnetted, 1 subnets
D 10.5.0.0[90/205901] via 192.168.1.2, S0/0/0
10.0.0.0/8 is subnetted, 4 subnets
D 10.5.0.0[90/205001] via 192.168.1.2, S0/0/0

26
Refer to the exhibit. An administrator is adding a new subnet of 50 hosts to
R3. Which subnet address should be used for the new subnet that provides
enough addresses while wasting a minimum of addresses?
192.168.1.0/24
192.168.1.48 /28
192.168.1.32/27
(true answer) 192.168.1.64/26

27
Refer to the exhibit. How many routes are ultimate routes?
3
4
(true answer) 5
7

28
Refer to the exhibit. Which router is advertising subnet 172.16.1.32/28?
Router1
Router2
Router3
(true answer) Router4

29
Which two statements are true about the EIGRP successor route? (Choose
two.)
It is saved in the topology table for use if the primary route fails.
(true answer) It may be backed up by a feasible successor route.
(true answer) It is used by EIGRP to forward traffic to the destination.
It is flagged as active in the routing table.
After the discovery process has occurred, the successor route is stored in the
neighbor table.

30
Refer to the exhibit. R2 is configured correctly. The network administrator
has configured R1 as shown. Which two facts can be deduced from the
configuration of R1? (Choose two.)
(true answer) R1 will forward the route information for subnet
192.168.100.0/30.
The administrative distance has been set to 50 on R1.
(true answer) R1 will not forward route information for subnet
192.168.100.4.0/30.
R1 will forward the EGRP update for subnet 10.10.10.0/30.
Autosummarization must be enabled.

31
Refer to the exhibit. All routers are running the same routing protocol. Based
on the exhibit and its displayed commands, which statement is true?
Routers B, C, and D have no access to the Internet.
(true answer) The link to the ISP will be excluded from the routing protocol
process.
A default route must be configured on every router.
The wildcard mask is incorrectly configured.

32
Which two components are used to determine the router ID in the
configuration of the OSPF routing process? (Choose two.)
the IP address of the first FastEthernet interface
(true answer) the highest IP address of any logical interface
(true answer) the highest IP address of any physical interface
the default gateway IP address
the priority value of 1 on any physical interface

33
Refer to the exhibit. R1 and R2 are unable to establish an adjacency. What
two configuration changes will correct the problem? (Choose
two.)
Set a lower priority on R2.
(true answer) Configure the routers in the same area.
Set a lower cost on R2 compared to R1.
Add a backup designated router to the network.
(true answer) Match the hello and dead timers on both routers.

34
Refer to the exhibit. All routers are properly configured to use the EIGRP
routing protocol with default settings, and the network is fully converged.
Which statement correctly describes the path that the traffic will use from
the 10.1.1.0/24 network to the 10.1.2.0/24 network?
It will use the A-D path only.
It will use the path A-D, and the paths A-C-D and A-B-D will be retained as
the backup paths.
It will use all the paths equally in a round-robin fashion.
(true answer) The traffic will be load-balanced between A-B-D and A-C-D.

35
Which routing protocol maintains a topology table separate from the routing
table?
IGRP
RIPv1
RIPv2
(true answer) EIGRP

36
Refer to the exhibit. A ping between the serial interfaces of R1 and R2 is
successful, but a ping between their FastEthernet interfaces fails. What is
the reason for this problem?
The FastEthernet interface of R1 is disabled.
(true answer) One of the default routes is configured incorrectly.
A routing protocol is not configured on both routers.
The default gateway has not been configured on both routers.

37
Refer to the exhibit. What action will R2 take for a packet that is destined for
192.168.2.0?
It will drop the packet.
It will forward the packet via the S0/0/0 interface.
It will forward the packet via the Fa0/0 interface.
(true answer) It will forward the packet to R1.

38
Refer to the exhibit. A network administrator has configured R1 as shown,
and all interfaces are functioning correctly. A ping from R1 to 172.16.1.1
fails. What could be the cause of this problem?
The serial interface on R1 is configured incorrectly.
(true answer) The default route is configured incorrectly.
The default-information originate command must be issued on R1.
Autosummarization must be disabled on R1.

39
Refer to the exhibit. All interfaces are addressed and functioning correctly.
The network administrator runs the tracert command on host A. Which two
facts could be responsible for the output of this command? (Choose two.)
(true answer) The entry for 192.168.2.0/24 is missing from the routing table
of R1.
(true answer) The entry for 192.168.1.0/24 is missing from the routing table
of R2.
The entry for 10.1.1.0/30 is missing from the routing table of R1.
The entry for 10.1.1.0/30 is missing from the routing table of R2.
The entry for 192.168.1.0/24 is missing from the routing table of R1.
The entry for 192.168.2.0/24 is missing from the routing table of R2.

40
A router has learned two equal cost paths to a remote network via the EIGRP
and RIP protocols. Both protocols are using their default configurations.
Which path to the remote network will be installed in the routing table?
(true answer) the path learned via EIGRP
the path learned via RIP
the path with the highest metric value
both paths with load balancing

41
Refer to the exhibit. The network has three connected routers: R1, R2, and
R3. The routes of all three routers are displayed. All routers are operational
and pings are not blocked on this network.
Which ping will fail?
from R1 to 172.16.1.1
(true answer) from R1 to 192.168.3.1
from R2 to 192.168.1.1
from R2 to 192.168.3.1

42
Refer to the exhibit. Which summarization should R1 use to advertise its
networks to R2?
192.168.1.0/24
192.168.0.0/24
(true answer) 192.168.0.0/22
192.168.1.0/22

43
Refer to the exhibit. Host A is unable to access the Internet. What is the
reason for this?
The IP address of host A is incorrect.
The default gateway of host A is incorrect.
(true answer) The Fa0/1 interfaces of the two routers are configured for
different subnets.
The subnet mask for the Fa0/0 interface of R1 is incorrect.
44
Refer to the exhibit. Which two components are required to complete the
configuration? (Choose two.)
a CSU/DSU device
(true answer) a DTE device
a DCE device
a crossover cable
(true answer) a V.35 cable

45
A router boots and enters setup mode. What is the reason for this?
The IOS image is corrupt.
Cisco IOS is missing from flash memory.
(true answer) The configuration file is missing from NVRAM.
The POST process has detected hardware failure.

46
Refer to the exhibit. A network administrator is accessing router R1 from the
console port. Once the administrator is connected to the router, which
password should the administrator enter at the R1> prompt to access the
privileged EXEC mode?
Cisco001
Cisco123
(true answer) Cisco789
Cisco901

47
Refer to the exhibit. While trying to diagnose a routing problem in the
network, the network administrator runs the debug ip rip command. What
can be determined from the output of this command?
The router will be unable to ping 192.168.1.2.
The router has two interfaces that participate in the RIP process.
The router will forward the updates for 192.168.1.0 on interface Serial0/0/1.
(true answer) The router is not originating routes for 172.16.1.0.

48
Refer to the exhibit. To implement the RIPv2 protocol, the network
administrator runs the commands as displayed. However, the show ip
protocol command fails to display any output. How can the administrator
solve the problem that is indicated by the lack of output from this command?
Include the default-information originate command.
Include the no auto-summary command.
(true answer) Specify the network for which RIP routing has to be enabled.
Implement RIPv2 authentication in the network.

49
Refer to the exhibit. Router R2 is configured properly and all interfaces are
functional. Router R1 has been installed recently. Host A is unable to ping
host B.
Which procedure can resolve this problem?
Configure a static route on R1 using the IP address of the serial interface on
R1.
Configure a default route on R1 with the exit interface Fa0/0 on R1.
(true answer) Configure a static route on R1 using the IP address of S0/0/0
on R2.
Configure a default route on R1 using the IP address of Fa0/0 on R2.

50
Refer to the exhibit. The show cdp neighbors command was run at R1. Which
two facts about the newly detected device can be determined from the
output? (Choose two.)
(true answer) ABCD is a router that is connected to R1.
ABCD is a non-CISCO device that is connected to R1.
(true answer) The device is connected at the Serial0/0/1 interface of R1.
R1 is connected at the S0/0/1 interface of device ABCD.
ABCD does not support switching capability.

51
Refer to the exhibit. A router learns a route to the 192.168.6.0 network, as
shown in the output of theshow ip rip database command. However, upon
running the show ip route command, the network administrator sees that the
router has installed a different route to the 192.168.6.0 network learned via
EIGRP. What could be the reason for the missing RIP route?
(true answer) Compared to RIP, EIGRP has a lower administrative distance.
Compared to EIGRP, RIP has a higher metric value for the route.
Compared to RIP, the EIGRP route has fewer hops.
Compared to RIP, EIGRP has a faster update timer.

52
All routers in a network are configured in a single OSPF area with the same
priority value. No loopback interface has been set on any of the routers.
Which secondary value will the routers use to determine the router ID?
The highest MAC address among the active interfaces of the network will be
used.
There will be no router ID until a loopback interface is configured.
The highest IP address among the active FastEthernet interfaces that are
running OSPF will be used.
(true answer) The highest IP address among the active interfaces will be
used.

53
Refer to the exhibit. Routers R1 and R2 are directly connected via their serial
interfaces and are both running the EIGRP routing protocol. R1 and R2 can
ping the directly connected serial interface of their neighbor, but they cannot
form an EIGRP neighbor adjacency.
What action should be taken to solve this problem?
Enable the serial interfaces of both routers.
Configure EIGRP to send periodic updates.
Configure the same hello interval between the routers.
(true answer) Configure both routers with the same EIGRP process ID.

54
Which three statements are true regarding the encapsulation and de-
encapsulation of packets when traveling through a router? (Choose three.)
(true answer) The router modifies the TTL field, decrementing it by one.
The router changes the source IP to the IP of the exit interface.
(true answer) The router maintains the same source and destination IP.
(true answer) The router changes the source physical address to the
physical address of the exit interface.
The router changes the destination IP to the IP of the exit interface.
The router sends the packet out all other interfaces, besides the one it
entered the router on.

55
Refer to the exhibit. Packets destined to which two networks will require the
router to perform a recursive lookup? (Choose two.)
(true answer) 10.0.0.0/8
64.100.0.0/16
128.107.0.0/16
172.16.40.0/24
192.168.1.0/24
(true answer) 192.168.2.0/24

56
Which two statements are correct about the split horizon with poison reverse
method of routing loop prevention? (Choose two.)
It is enabled by default on all Cisco IOS implementations.
(true answer) It assigns a value that represents an infinite metric to the
poisoned route.
(true answer) It sends back the poisoned route update to the same interface
from where it was received.
It instructs routers to hold all changes that might affect routes, for a
specified period of time.
It limits the number of hops a packet can traverse through the network
before it is discarded.

57
A network administrator has enabled RIP on routers B and C in the network
diagram. Which of the following commands will prevent RIP updates from
being sent to Router A?
A(config)# router rip
A(config-router)# passive-interface S0/0
B(config)# router rip
B(config-router)# network 192.168.25.48
B(config-router)# network 192.168.25.64
A(config)# router rip
A(config-router)# no network 192.168.25.32
(true answer) B(config)# router rip
B(config-router)# passive-interface S0/0
A(config)# no router rip

*88

CCNA 2 – Final 94,8% – New

http://p4s-ccna.blogspot.com
1. Refer to the exhibit. All routers are running the same routing protocol.
Based on the exhibit and its displayed commands, which statement is true?
ans:
The link to the ISP is not advertised by the routing protocol process.

2. Refer to the exhibit. While trying to diagnose a routing problem in the

network, the network administrator runs the debug ip rip command. What
can be determined from the output of this command?
ans:
The router will be unable to ping 192.168.1.2.

3. Refer to the exhibit. Two routers are unable to establish an adjacency.

What is the possible cause for this?
ans:
The hello and dead intervals are different on the two routers.

4. Refer to the exhibit. Routers R1 and R2 are directly connected via their
serial interfaces and are both running the EIGRP routing protocol. R1 and R2
can ping the directly connected serial interface of their neighbor, but they
cannot form an EIGRP neighbor adjacency?
ans:
Configure both routers with the same EIGRP process ID.

5. Refer to the exhibit. Routers R1 and R3 use different routing protocols

with default administrative distance values. All devices are properly
configured and the destination network is advertised by both protocols.
Which path will be used to transmit the data packets from PC1 to PC2?
ans:
The packets will travel via R2-R1.

6. Refer to the exhibit. What is the meaning of the highlighted value 2?

ans:
It is the number of hops between R2 and the 192.168.8.0/24 network.

7. What is the function of the OSPF LSR packet?

ans:
It is used by the receiving routers to request more information about any
entry in the DBD.

8. Which three statements are true regarding the encapsulation and de-
encapsulation of packets when traveling through a router? (Choose three.)

The router modifies the TTL field, decrementing it by one.

The router maintains the same source and destination IP.
The router changes the source physical address to the physical address of
the exit interface.

9. Refer to the exhibit. The routers are properly configured using a dynamic
routing protocol with default settings, and the network is fully converged.
Router A is forwarding data to router E. Which statement is true about the
routing path?

If the network uses the RIP protocol, router A will determine that all paths
have equal cost.

10. Refer to the exhibit. A network administrator has run the show interface
command. The output of this command is displayed. What is the first step
that is required to make this interface operational?

Issue the no shutdown command on the interface.

11. Refer to the exhibit. Both routers are using the RIPv2 routing protocol
and static routes are undefined. R1 can ping 192.168.2.1 and 10.1.1.2, but is
unable to ping 192.168.4.1.
What is the reason for the ping failure?

The 192.168.4.0 network is not included in the RIP configuration of R2.

12. Refer to the exhibit. R2 is configured correctly. The network

administrator has configured R1 as shown. Which two facts are true about
the forwarding of route information by R1? (Choose two.)
R1 will forward the route information for subnet 192.168.100.0/30.
R1 will forward the route information with an administrative distance set to
50.

13. Refer to the exhibit. The network has three connected routers: R1, R2,
and R3. The routes of all three routers are displayed. All routers are
operational and pings are not blocked on this network. Which ping will fail?
from R1 to 192.168.3.1
14. Refer to the exhibit. A network administrator has configured R1 as
shown, and all interfaces are functioning correctly. A ping from R1 to
172.16.1.1 fails. What could be the cause of this problem?
The default route is configured incorrectly.

15. Which two router component and operation pair are correctly described?
(Choose two.)
NVRAM – stores the configuration file
POST – runs diagnostics on hardware modules

16. A network administrator uses the RIP routing protocol to implement

routing within an autonomous system. What are two characteristics of this
protocol? (Choose two.):
It uses the Bellman-Ford algorithm to determine the best path.
It periodically sends complete routing tables to all connected devices.

17. Refer to the exhibit. Host A is unable to access the Internet. What is the
reason for this?
-The Fa0/1 interfaces of the two routers are configured for different subnets.

18. Refer to the exhibit. All interfaces are addressed and functioning
correctly. The network administrator runs the tracert command on host A.
Which two facts could be responsible for the output of this command?
(Choose two.)

The entry for 192.168.2.0/24 is missing from the routing table of R1.
The entry for 192.168.2.0/24 is missing from the routing table of R2.

19. What are two functions of a router? (Choose two.)

It forwards data packets toward their destination.

It acts as an intersection between multiple IP networks.

20. Which statement is true about the RIPv1 protocol?

It excludes subnet information from the routing updates.

21. Refer to the exhibit. To implement the RIPv2 protocol, the network
administrator runs the commands as displayed. However, the show ip
protocol command fails to display any output. How can the administrator
solve the problem that is indicated by the lack of output from this command?
Specify the network for which RIP routing has to be enabled.

22. Refer to the exhibit. An administrator is adding a new subnet of 50 hosts

to R3. Which subnet address should be used for the new subnet that
provides enough addresses while wasting a minimum of addresses?
192.168.1.64/26

23. Refer to the exhibit. R1 and R2 are unable to establish an adjacency.

What two configuration changes will correct the problem? (Choose two.)
Configure the routers in the same area.
Match the hello and dead timers on both routers.

24. What two routing protocols use a hierarchal network topology? (Choose
two.)
IS-IS
OSPF

25. Refer to the exhibit. Router R2 is configured properly and all interfaces
are functional. Router R1 has been installed recently. Host A is unable to
ping host B.
Which procedure can resolve this problem?
Configure a static route on R1 using the IP address of S0/0/0 on R2.

26. All routers in a network are configured in a single OSPF area with the
same priority value. No loopback interface has been set on any of the
routers. Which secondary value will the routers use to determine the router
ID?
The highest IP address among the active interfaces will be used.

27. Which two statements are true for link-state routing protocols? (Choose
two.)
Routers that run a link-state protocol can establish a complete topology of
the network.
The shortest path first algorithm is used.

28. A router boots and enters setup mode. What is the reason for this?
The configuration file is missing from NVRAM.

29. Refer to the exhibit. The show cdp neighbors command was run at R1.
Which two facts about the newly detected device can be determined from
the output? (Choose two.)
ABCD is a router that is connected to R1.
The device is connected at the Serial0/0/1 interface of R1.

30. What are two tasks that must be completed before two routers can use
OSPF to form a neighbor adjacency? (Choose two.)
The routers must agree on the network type.
The routers must use the same dead interval.

31. Refer to the exhibit. A ping between host A and host B is successful, but
pings from host A to operational hosts on the Internet fail. What is the
reason for this problem?
One of the default routes is configured incorrectly.

32. What two routing protocols will produce a shortest path first tree?
(Choose two.)
IS-IS
OSPF

33. Refer to the exhibit. Which three statements are true of the routing table
for Router1? (Choose three.)
The AD of EIGRP routes has been manually changed to a value other than
the default value.
Router1 is running both the EIGRP and OSPF routing process.
No default route has been configured.

34. Refer to the exhibit. What action will R2 take for a packet that is destined
for 192.168.2.0?
It will forward the packet to R1.

35. Refer to the exhibit. A router learns a route to the 192.168.6.0 network,
as shown in the output of the show ip rip database command. However,
upon running the show ip route command, the network administrator sees
that the router has installed a different route to the 192.168.6.0 network
learned via EIGRP. What could be the reason for the missing RIP route?
Compared to RIP, EIGRP has a lower administrative distance.

36. Which two components are used to determine the router ID in the
configuration of the OSPF routing process? (Choose two.)
ans:
the highest IP address of any logical interface
the highest IP address of any physical interface

37. Refer to the exhibit. A network administrator is accessing router R1 from

the console port. Once the administrator is connected to the router, which
password should the administrator enter at the R1> prompt to access the
privileged EXEC mode?
ans:
Cisco789

38. Which routing protocol maintains a topology table separate from the
routing table?
ans:
EIGRP

39. Refer to the exhibit. Which summarization should R1 use to advertise its
networks to R2?
ans:
192.168.0.0/22

40. Refer to the exhibit. All routers are running RIPv1. The two networks
10.1.1.0/29 and 10.1.1.16/29 are unable to access each other. What can be
the cause of this problem?
ans:
RIPv1 does not support discontiguous networks.

41. Refer to the exhibit. All routers are properly configured to use the EIGRP
routing protocol with default settings, and the network is fully converged.
Which statement correctly describes the path that the traffic will use from
the 10.1.1.0/24 network to the 10.1.2.0/24 network?
ans:
The traffic will be load-balanced between A-B-D and A-C-D.

42. A network administrator has enabled RIP on routers B and C in the

network diagram. Which of the following commands will prevent RIP updates
from being sent to Router A?
ans:
B(config)# router rip
B(config-router)# passive-interface S0/0
43. Which two statements are correct about the split horizon with poison
reverse method of routing loop prevention? (Choose two.)
ans:
It assigns a value that represents an infinite metric to the poisoned route.
It sends back the poisoned route update to the same interface from where it
was received.

44. Refer to the exhibit. The 10.4.0.0 network fails. What mechanism
prevents R2 from receiving false update information regarding the 10.4.0.0
network?
ans:
split horizon

45. Refer to the exhibit. How many routes are ultimate routes?
ans:
5

46. Refer to the exhibit. Which two statements are true based on the
exhibited output? (Choose two.)
ans:
All routes are stable.
The show ip eigrp topology command has been run on R1.

47. A router has learned two equal cost paths to a remote network via the
EIGRP and RIP protocols. Both protocols are using their default
configurations. Which path to the remote network will be installed in the
routing table?
ans:
the path learned via EIGRP

48. Which two statements are true about the EIGRP successor route?
(Choose two.)
ans:
It may be backed up by a feasible successor route.
It is used by EIGRP to forward traffic to the destination.

49. Refer to the exhibit. The output of the show ip route command for router
R1 is displayed. What action will the router take for a packet that is destined
for 192.168.1.5?
ans:
It will forward the packet to the default gateway.

50. Refer to the exhibit. The hosts that are connected to R2 are unable to
ping the hosts that are connected to R1. How can this problem be resolved?
ans:
Configure the R2 router interfaces for area 0.

51. In a lab test environment, a router has learned about network 172.16.1.0
through four different dynamic routing processes. Which route will be used
to reach this network?
ans:
D 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Serial0/0/0

52. Refer to the exhibit. Which two facts can be derived from this output?
(Choose two.)
ans:
Three network devices are directly connected to Router2.
The serial interface between Router2 and Router3 is up.

53. How does route poisoning prevent routing loops?

ans:
Failed routes are advertised with a metric of infinity.

54. Refer to the exhibit. A network administrator wants to reduce the size of
the routing table of R1. Which partial routing table entry in R1 represents the
route summary for R2, without including any additional subnets?
ans:
10.0.0.0/22 is subnetted, 1 subnets
D 10.5.0.0[90/205901] via 192.168.1.2, S0/0/0

55. Refer to the exhibit. Packets destined to which two networks will require
the router to perform a recursive lookup? (Choose two.)
ans:
10.0.0.0/8
192.168.2.0/24

56. Refer to the exhibit. Although R2 is configured correctly, host A is unable

to access the Internet. What are two static routes that can be configured on
R1, either of which would enable Internet connectivity for host A? (Choose
two.)
ans:
ip route 0.0.0.0 0.0.0.0 Fa0/1
ip route 0.0.0.0 0.0.0.0 10.1.1.2

57. Refer to the exhibit. Which router is advertising subnet 172.16.1.32/28?

ans:
Router4

58. Which statement is true about the metrics used by routing protocols?
ans:
A metric is a value used by a particular routing protocol to compare paths to
remote networks.

59. Refer to the exhibit. Which two components are required to complete the
configuration? (Choose two.)
ans:
a DTE device

*88888888

CCNA2 FINAL2 (new 25/12/08)

1. Refer to the exhibit. The output of the show ip route command for three
routers on a network is displayed. All routers are operational, pings are not
blocked on this network, and no default routes are installed. Which two pings
will fail? (Choose two.)
from R1 to 172.16.1.1
** from R1 to 192.168.3.1
from R2 to 192.168.1.1
from R2 to 192.168.3.1
** from R3 to 192.168.1.1
172.16.4.0/24

2. A router that uses the RIP routing protocol has an entry for a network in
the routing table. It then receives an update with another entry for the same
destination network but with a lower hop count. What action will the router
take for this new update?
** It will append the update information to the routing table.
It will invalidate the entry for that network in the routing table.
It will replace the existing routing table entry with the new information.
It will ignore the new update.

3. Which two statements are true for OSPF Hello packets? (Choose two.)
They negotiate correct parameters among neighboring interfaces.
They are used for dynamic neighbor discovery.
They use timers to elect the designated router with the fastest link.
** They are received from all routers on the network and used to determine
the complete network topology.
** They are used to maintain neighbor relationships.

4. A network administrator needs to configure a single router to loadbalance

the traffic over unequal cost paths. Which routing protocol should the
administrator use?
EIGRP
OSPF
RIPv1
** RIPv2

5. Which two statements are correct about the split horizon with poison
reverse method of routing loop prevention? (Choose two.)
It is enabled by default on all Cisco IOS implementations.
** It assigns a value that represents an infinite metric to the poisoned route.
** It sends back the poisoned route update to the same interface from where
it was received.
It instructs routers to hold all changes that might affect routes, for a
specified period of time.
It limits the number of hops a packet can traverse through the network
before it is discarded.

6. Refer to the exhibit. The show cdp neighbors command was run on one of
the devices as shown. Based on this information, which two facts can be
determined? (Choose two.)
** The command was run on the router.
ABCD is a non CISCO device.
Layer 3 connectivity between two devices exists.
ABCD supports routing capability.
** ABCD is connected to the Fa0/0 interface of the neighboring device.
7. Refer to the exhibit. The network has three connected routers: R1, R2 and
R3. The routes of all three routers are displayed. What can be verified from
the output?
R1 and R3 are connected to each other via the S0/0/0 interface.
The IP address of the S0/0/0 interface of R1 is 10.1.1.2.
The IP address of the S0/0/1 interface of R2 is 10.3.3.2.
** R2 is connected to the S0/0/1 interface of R3.

8. Refer to the exhibit. Which three statements are true of the routing table
for Router1? (Choose three.)
The route to network 172.16.0.0 has an AD of 156160.
Network 192.168.0.16 can best be reached using FastEthernet0/0.
**The AD of EIGRP routes has been manually changed to a value other than
the default value.
** Router1 is running both the EIGRP and OSPF routing process.
Network 172.17.0.0 can only be reached using a default route.
** No default route has been configured.

9. Refer to the exhibit. All the routers are properly configured to use the RIP
routing protocol with default settings, and the network is fully converged.
Router A is forwarding data to router E. Which statement is true about the
routing path?
Router A will send the data via the ADE path that is listed in the routing
table.
Router A will loadbalance the traffic between ABE and ACE.
** Router A will determine that all paths have equal metric cost.
Router A will send the data through ADE and keep ABE and ACE as the
backup paths.

10. Refer to the exhibit. The network administrator has run the following
command on R1.
R1# ip route 192.168.2.0 255.255.255.0 172.16.1.2What is the result of
running this command?
** Traffic for network 192.168.2.0 is forwarded to 172.16.1.2.
This route is automatically propagated throughout the entire network.
Traffic for all networks is forwarded to 172.16.1.2.
The command invokes a dynamic routing protocol for 192.168.2.0.

11. Refer to the exhibit. The network administrator is planning IP addressing

of a new network. What part of this addressing scheme must be changed to
allow communication between host A and the server?
** the IP address of the server
the default gateway of host A
the IP address of host A
the default gateway of the server

12. Refer to the exhibit. A network administrator has configured OSPF using
the following command:
network 192.168.1.32 0.0.0.31 area 0
Which router interface will participate in OSPF?
FastEthernet 0/0
FastEthernet 0/1
** Serial 0/0/0
Serial 0/0/1

13. Refer to the exhibit. All routers are configured to run RIPv1 and are fully
converged. Which routing updates will be received by R3?
updates for 192.168.1.0/24 and 192.168.2.0/24
updates for 172.16.2.0/24 and 172.16.3.0/24
** updates for 172.16.1.0/24, 172.16.2.0/24 and 172.16.3.0/24
updates for 172.16.0.0/16

14. Refer to the exhibit. Both routers are using the RIP protocol. Devices on
the 192.168.1.1 network can ping the S0/0/0 interface on R2 but cannot ping
devices on the 192.168.2.1 network. What is a possible cause of this
problem?
** The routers are configured with different versions of RIP.
R2 is not forwarding the routing updates.
The R1 configuration should include the no autosummary command.
The maximum path number has been exceeded.

15. When a router boots, what is the default order to locate the Cisco IOS if
there is no boot system command?
ROM, TFTP server, flash
flash, TFTP server, RAM
** flash, NVRAM, TFTP server
ROM, flash, TFTP server

16. Refer to the exhibit. Which router is advertising subnet 172.16.1.32/28?

Router1
Router2
Router3
** Router4

17. Which mechanism helps to avoid routing loops by advertising a metric of

infinity?
** route poisoning
split horizon
holddown timer
triggered updates

18. Refer to the exhibit. What is the meaning of the highlighted value 120?
It is the metric that is calculated by the routing protocol.
It is the value that is used by the DUAL algorithm to determine the
bandwidth for the link.
** It is the administrative distance of the routing protocol.
It is the holddown time, measured in seconds, before the next update.

19. Refer to the exhibit. A network administrator successfully pings R1 from

R3. Next, the administrator runs the show cdp neighbors command on R3.
The output of this command is displayed.What are two reasons for the
absence of R1 in the output? (Choose two.)
There is a Layer 2 connectivity problem between R1 and R3.
The Fa0/0 interface of R1 is configured with an incorrect IP address.
**The no cdp run command has been run at R1.
**The no cdp enable command has been run at Fa0/1 interface of R3.R1 is
powered off.

20. Refer to the exhibit. A device is required to complete the connection

between router R1 and the WAN. Which two devices can be used for this?
(Choose two.)
** a CSU/DSU device
** a modem
an Ethernet switch
a hub
a bridge

21. In a complex lab test environment, a router has discovered four paths to
192.168.1.0/24 via the use of the RIP routing process. Which route will be
installed in the routing table after the discovery of all four paths?
R 192.168.1.0/24 [120/3] via 192.168.110.1, 00:00:17, Serial 0/1/0
R 192.168.1.0/24 [120/2] via 192.168.200.1, 00:00:17, Serial 0/0/0
** R 192.168.1.0/24 [120/1] via 192.168.100.1, 00:00:17, Serial 0/0/1
R 192.168.1.0/24 [120/4] via 192.168.101.1, 00:00:17, Serial 0/1/1

22. Refer to the exhibit. A network administrator accesses router R1 from the
console port to configure a newly connected interface. What passwords will
the network administrator need to enter to make the connection and the
necessary configuration changes?
the Cisco123 password only
the Cisco789 password only
the Cisco001 password only
** the Cisco001 password and the Cisco789 passwords
the Cisco001 password and the Cisco123 passwords

23. Refer to the exhibit. A network administrator adds this command to

router R1: ip route 192.168.2.0 255.255.255.0 S0/0/0. What is the result of
adding this command?
This route is automatically propagated throughout the network.
The traffic for network 172.16.1.0 is forwarded to network 192.168.2.0.
** A static route is established.
The traffic for all Class C networks is forwarded to 172.16.1.2.

24. Refer to the exhibit. The router receives a packet that is destined for
192.168.5.79. How will the router handle this packet?
It will forward the packet via the Serial0/0/1 interface.
It will forward the packet via the FastEthernet0/0 interface.
It will forward the packet via the Serial0/0/0 interface.
** It will drop the packet.

25. Which two statements are true about classless routing protocols?
(Choose two.)
** They can be used for discontiguous subnets.
** They can forward supernet routes in routing updates.
They cannot implement classful routes in routing tables.
They use only a hop count metric.
They do not include the subnet mask in routing updates.

26. Refer to the exhibit. How many routes are child routes?
1
3
** 4
6

27. A router has EIGRP configured as the only routing protocol. In what two
ways does EIGRP respond if there is no feasible successor route to a
destination network and the successor route fails? (Choose two.)
It broadcasts hello packets to all routers in the network to reestablish
neighbor adjacencies.
** It sends queries to adjacent neighbors until a new successor route is
found.
It immediately sends its entire routing table to its neighbors.
It sends queries to adjacent neighbors until the lost route is unknown to the
neighbors.
** It automatically forwards traffic to a fallback default route until a
successor route is found.

28. Refer to the exhibit. Packets destined to which two networks will require
the router to perform a recursive lookup? (Choose two.)
** 10.0.0.0/8
64.100.0.0/16
128.107.0.0/16
172.16.40.0/24
192.168.1.0/24
** 192.168.2.0/24

29. Refer to the exhibit. Which two statements are true based on the
exhibited output? (Choose two.)
The administrative distance of EIGRP has been set to 50.
** All routes are stable.
** The show ip eigrp topology command has been run on R1.
The serial interface between the two routers is down.
Each route has one feasible successor.

30. Refer to the exhibit. All routers are properly configured with default
configurations and are running the OSPF routing protocol. The network is
fully converged. A host on the 192.168.3.0/24 network is communicating
with a host on the 192.168.2.0/24 network. Which path will be used to
transmit the data?
The data will be transmitted via R3-R2.
** The data will be transmitted via R3-R1-R2.
The traffic will be loadbalanced between two paths — one via R3-R2, and the
other via R3-R1-R2.
The data will be transmitted via R3-R2, and the other path via R3-R1-R2 will
be retained as the backup path.

31. A network administrator has enabled RIP on routers B and C in the

network diagram. Which of the following commands will prevent RIP updates
from being sent to Router A?
** A(config)# router rip
A(configrouter)# passiveinterface S0/0
B(config)# router rip
B(configrouter)# network 192.168.25.48
B(configrouter)# network 192.168.25.64
A(config)# router rip
A(configrouter)# no network 192.168.25.32
B(config)# router rip
B(configrouter)# passiveinterface S0/0
A(config)# no router rip

32. Refer to the exhibit. The hosts on the R1 LAN are unable to access the
Internet. What is incorrectly configured?
the IP address of the Fa 0/0 interface at R1
the IP address of the S 0/0/1 interface at R2
** the IP address of the S 0/0/0 interface at R1
the subnet mask of the S 0/0/1 interface at R2

33. Refer to the exhibit. A ping from R1 to 10.1.1.2 is successful, but a ping
from R1 to 192.168.2.0 fails. What is the cause of this problem?
There is no gateway of last resort at R1.
The serial interface between the two routers is down.
** A default route is not configured on R1.
The static route for 192.168.2.0 is incorrectly configured.

34. Refer to the exhibit. The network administrator has run the show ip
protocol command on R1. What can be determined from the exhibited
output?
The router is using RIPv2.
The router is not forwarding routing updates.
The router is receiving updates for both versions of RIP.
** The FastEthernet0/0 interface is down.

35. Refer to the exhibit. All routers are configured to use the EIGRP routing
protocol with default settings, all routes are advertised on all routers, and
the network is fully converged. Which path will the data take to travel
between 172.16.1.0/24 and 192.168.100.0/24?
It will travel via A, B, and C.
** It will travel via A, F, E, D, and C.
It will travel via A, G, H, and C.
The traffic will be loadbalanced on all paths.

36. Refer to the exhibit. All routers are configured for OSPF area 0. The
network administrator requires that R2 always be the DR and maintain
adjacency.Which two configurations can achieve this? (Choose two.)
Change the OSPF area of R2 to a higher value.
Change the router ID for R2 by assigning the IP address 172.16.30.5/24 to
the Fa0/0 interface.
** Change the priority values of the Fa0/0 interfaces of R1 and R3 to 0.
** Configure a loopback interface on R2, with an IP address higher than any
IPaddress on the other routers.
Configure R1 and R3 with an IP address whose value is higher than that of
R2.

37. Refer to the exhibit. Host A is unable to access the Internet, and
troubleshooting has revealed that this is due to an addressing problem.
What is incorrectly configured in this network?
the IP address of the Fa 0/0 interface of R1
the subnet mask of the S 0/0/0 interface of R1
** the IP address of the S 0/0/0 interface of R1
the subnet mask of the S0/0/0 interface of R2

38. Refer to the exhibit. All routes are advertised and fully operational on all
routers. Which statement is true about the path that the data will take from
router A to router B?
** If EIGRP is used with default configurations, the data will be equally
distributed between two paths — A, D, B and A, C, D.
If RIPv1 is used with default configurations, the data will be loadbalanced on
all paths.
If EIGRP and OSPF are both used with default configurations, the data will be
sent through paths learned by the OSPF protocol.
If RIPv2 is used with default configurations, the data will be equally
distributed between two paths — A, D, B and A, C, D.

39. Refer to the exhibit. The interfaces of all routers are configured for OSPF
area 0. R3 can ping R1, but the two routers are unable to establish a
neighbor adjacency. What should the network administrator do to
troubleshoot this problem?
Check if the interfaces of the routers are enabled.
** Check the hello and dead intervals between the routers.
Check the process ID of both routers.
Check if CDP is enabled on all the routers.

40. Refer to the exhibit. What information can be determined from the
highlighted output?
R1 is originating the route 172.30.200.32/28.
** Automatic summarization is disabled.
The 172.30.200.16/28 network is one hop away from R1.
A classful routing protocol is being used.

41. Which two router component and operation pair are correctly described?
(Choose two.)
DRAM loads the bootstrap
RAM stores the operating system
Flash executes diagnostics at bootup
** NVRAM stores the configuration file
ROM stores the backup configuration file
** POST runs diagnostics on hardware modules

42. Which routing protocol by default uses bandwidth and delay to calculate
the metric of a route?
RIPv1
RIPv2
OSPF
** EIGRP

43. Two routers need to be configured within a single OSPF area. Which two
components need to be configured on both routers to achieve this? (Choose
two.)
the same process ID
** the same area ID
** network addresses and wildcard masks
the same router ID
the same loop back address

44. Refer to the exhibit. The networks that are connected to R1 have been
summarized for R2 as 192.168.136.0/21. Which packet destination address
will R2 forward to R1?
192.168.135.1
**192.168.142.1
192.168.144.1
192.168.128.1

45. Refer to the exhibit. R1 is running RIP with default parameters. R1 has
learned four different paths with the same metrics to network 192.168.6.0.
Which path or paths will R1 use to forward a packet that is destined to
192.168.6.10?
** the first path that the router learned.
only the first two of the four paths that the router learned.
the last path that the router learned.
all four paths.

46. What are two functions of a router? (Choose two.)

** It connects multiple IP networks.
It controls the flow of data via the use of Layer 2 addresses.
** It determines the best path to send packets.
It manages the VLAN database.
It increases the size of the broadcast domain.

47. Refer to the exhibit. Which statement is true about the routing process
for this network?
A packet leaves interface Fa0/0 of R1 with the source MAC address as
000C.3010.9260.
** The packet leaves interface Fa0/0 of R1 with the source MAC address as
000C.3010.9260.
The no shutdown command needs to run on the Fa0/0 interface of R1.
The Fa0/0 interface of R2 could be configured with the IP address
172.16.4.1/24.

48. Refer to the exhibit. A network administrator has run the show interface
command. The output of this command is displayed. What is the first step
that is required to make this interface operational?
Switch the cable with a known working cable.
** Issue the no shutdown command on the interface.
Configure the interface as a loopback interface.
Set the encapsulation for the interface.

49. Refer to the exhibit. R1 is configured properly for a single area OSPF, and
R2 has been recently installed in the network. Which set of commands is
required to configure a single area OSPF for the networks that are connected
to R2?
** R2(config)# router ospf 1
R2(configrouter)# network 192.168.2.0 0.0.0.255 area 0
R2(configrouter)# network 10.1.1.0 0.0.0.3 area 0
R2(config)# router ospf 1
R2(configrouter)# network 192.168.2.0 0.0.0.255 area 0

R2(config)# router ospf 2

R2(configrouter)# network 10.1.1.0 0.0.0.3 area 0
R2(config)# router ospf 1
R2(configrouter)# network 192.168.2.0 0.0.0.255 area 0
R2(configrouter)# network 10.1.1.0 0.0.0.3 area 1
R2(config)# router ospf 1
R2(configrouter)# network 192.168.2.0 0.0.0.255 area 0
R2(configrouter)# network 10.0.0.0 0.0.0.3 area 1

50. Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run
on router R2. What are the two results of this command? (Choose two.)
** A static route will be updated in the routing table.
The traffic from the Internet will be directed to R2.
The traffic from the source network 172.16.0.0/22 will be blocked.
** The route will be specified as the default route for all networks not defined
in the routing table.
All the broadcasts will be forwarded via the S0/0/0 interface of R2.

51. Which three statements are true regarding the encapsulation and
deencapsulation of packets when traveling through a router? (Choose three.)
** The router modifies the TTL field, decrementing it by one.
The router changes the source IP to the IP of the exit interface.
** The router maintains the same source and destination IP.
** The router changes the source physical address to the physical address of
the exit interface.
The router changes the destination IP to the IP of the exit interface.
The router sends the packet out all other interfaces, besides the one it
entered the router on.

52. What are two tasks that must be completed before two routers can use
OSPF to form a neighbor adjacency? (Choose two.)
The routers must elect a designated router.
** The routers must agree on the network type.
** The routers must use the same dead interval.
The routers must exchange link state requests.
The routers must exchange database description packets.

53. Refer to the exhibit. Although both the routers can ping the serial
interface of their neighbors, they are unable to ping the Ethernet interfaces
of other routers. Which two statements are true for this network? (Choose
two.)
The administrative distance has been set to 50 on both routers.
** R2 is learning about network 192.168.1.0.
R1 is learning about network 192.168.2.0.
The network 10.1.1.0 command has not been run on both routers.
** Autosummarization is enabled on both routers.

54. Which two situations require the use of a linkstate protocol? (Choose
two.)
** Fast convergence of the network is critical.
** The network is very large.
The network administrator has limited knowledge to configure and
troubleshoot routing protocols.The network is a flat network.
The capacity of the router is low.

55. Refer to the exhibit. What information can be determined from the
displayed output?
EIGRP packets are waiting to be sent to the neighbors.
The adjacencies between the routers are yet to be established.
The IP address 192.168.10.10 is configured at serial interface S0/0/1 of
router R2.
** Router R2 is receiving hello packets from a neighbor with the IP address
192.168.10.10 via the R2 S0/0/1 interface.
56. Refer to the exhibit. PC1 is unable to access the Internet. What is the
cause of the problem?
An incorrect IP address is configured between the two routers.
No static route is configured on Router2.
** A routing loop has occurred.
No routing protocol is configured on either of the two routers.

57. Refer to the exhibit. What summarization should R2 use to advertise its
LAN networks to R1?
172.16.0.0/24

88************

CCNA 2 - Final Exam (A)

1. Refer to the exhibit. The network administrator issues the command no ip

classless on Router1. What forwarding action will take place on a packet that
is received by Router1 and is destined for host 192.168.0.26?
• The packet will be dropped
• The packet will be forwarded to the gateway of last resort.
• The packet will match the 192.168.0.0 network and be forwarded out
Serial 0/0.
• The packet will most closely match the 192.168.0.8 subnet and be
forwarded out Serial 0/1.
2. Which three statements are true of holddown timers? (Choose three.)
• used by link state routing protocols to prevent routing loops
• prevent update messages from reinstating a route that may have gone
bad
• allow routers to still forward packets to destination networks that are in
holddown
• limit the number of hops a packet can traverse through the network before
it is discarded
• prevent a router advertising a network through the same interface from
which the network was learned
• permit lower metric updates received from any neighboring router to
reinstate the route to a possibly down Network
3. What command would the network administrator apply to a router that is
running OSPF to advertise the entire range of addresses included in
172.16.0.0/19 in area 0?
• R1(config-router)# network 172.16.0.0 0.0.0.255 area 0
• R1(config-router)# network 172.16.0.0 0.0.3.255 area 0
• R1(config-router)# network 172.16.0.0 0.0.15.255 area 0
• *R1(config-router)# network 172.16.0.0 0.0.31.255 area 0
4. Refer to the exhibit. Hosts on the BOS Fa0/0 LAN are able to ping the
Fa0/1 interface on the JAX router and all interfaces on the BOS and ORL
routers. Why would hosts from the 10.0.0.0/24 network not be able to ping
hosts on the Fa0/0 LAN of the JAX router?
• The JAX router has the wrong process ID.
• The JAX router needs the network 10.0.0.0 0.0.0.255 area 0 command.
• The JAX router needs the network 192.168.3.0 0.0.0.255 area 0 command.
• The BOS router needs the network 192.168.3.0 0.0.0.255 area 0 command.
5. Refer to the exhibit. Which path will traffic from the 172.16.1.0/24 network
take to get to the 10.0.0.0/24 network?
• ADC
• ABC
• It will load balance the traffic between ADC and ABC
• It will send the traffic via ABC, and will use ADC as a backup path only
when ABC fails.
6. Refer to the exhibit. Pings are failing between HostA and HostB. The
network administrator discovers that Router1 does not have a route to the
172.16.0.0 network. Assuming Router2 is configured correctly, which two
static routes could be configured on Router1 to enable Host A to reach
network 172.16.0.0? (Choose two.)
• ip route 172.16.0.0 255.255.0.0 S0/0
• ip route 172.16.0.0 255.255.0.0 S0/1
• ip route 172.16.0.0 255.255.0.0 192.168.0.1
• ip route 172.16.0.0 255.255.0.0 192.168.0.2
• ip route 192.168.0.1 172.16.0.0 255.255.0.0 S0/0
• ip route 192.168.0.1 172.16.0.0 255.255.0.0 S0/1
7. What can be determined from the output shown in the exhibit? (Choose
two.)
• Annapolis is a 2611 router that is connected to the S0/0 interface of the
Montgomery router.
• All of the routers are connected to Montgomery through an Ethernet
switch.
• Montgomery has Layer 2 connectivity with Cumberland.
• Layer 3 connectivity is operational for all of the devices listed in the Device
ID column.
• An administrator consoled into the Waldorf router can ping the Brant
router.
• Brant, Fisherman, and Potomac are directly connected to Montgomery.
8. Refer to the exhibit. R1 knows two routes, Path A and Path B, to the
Ethernet network attached to R3. R1 learned Path A to network 10.2.0.0/16
from a static route and Path B to network 10.2.0.0/16 from EIGRP. Which
route will R1 install in its routing table?
• Both routes are installed and load balancing occurs across both paths.
• The route via Path B is installed because the EIGRP route has the best
metric to network 10.2.0.0/16.
• The route via Path A is installed because the static route has the best
metric to network 10.2.0.0/16.
• The route via Path B is installed because the EIGRP route has the lowest
administrative distance to network 10.2.0.0/16.
• The route via Path A is installed because the static route has the lowest
administrative distance to network 10.2.0.0/16.
9. Which two statements are true regarding link-state routing protocols?
(Choose two.)
• They do not work well in networks that require special heirarchical designs.
• They are aware of the complete network topology.
• They pass their entire routing tables to their directly connected neighbors
only.
• They offer rapid convergence times in large networks.
• They rely on decreasing hop counts to determine the best path.
• They do not include subnet masks in their routing updates.
10. A network administrator has configured a default route on Router_A but
it is not being shared with adjacent Router_B and the other routers in the
OSPF area. Which command will save the administrator the time and trouble
of configuring this default route on Router_B and all of the other routers in
the OSPF area?
• Router_A(config-router)# ospf redistribute default-route
• Router_B(config-router)# ospf redistribute default-route
• Router_A(config-router)# default-information originate
• Router_B(config-router)# default-information originate
• Router_A(config-router)# ip ospf update-default
• Router_B(config-router)# ip ospf update-default
11. Refer to the exhibit. What are the effects of the exhibited commands on
the router?
All passwords are encrypted.
• Only Telnet sessions are encrypted.
• Only the enable password is encrypted.
• Only the enable password and Telnet session are encrypted.
• Enable and console passwords are encrypted.
12. When presented with multiple valid routes to a destination, what criteria
does a router use to determine which routes to add to the routing table?
• The router selects the routes with the best metric. All routes that have the
same best metric are added to the routing table.
• The router first selects routes with the lowest administrative distance. The
resulting routes are then prioritized by metric and the routes with the best
metric are added to the routing table.
• The router selects the routes with the lowest administrative distance. All
routes with the same lowest administrative distance are added to the routing
table.
• The router installs all routes in the routing table but uses the route with the
best metric most when load balancing.
13. Which statement is true regarding routing metrics?
• All routing protocols use the same metrics.
• EIGRP uses bandwidth as its only metric.
• Routers compare metrics to determine the best route.
• The larger metric generally represents the better path.
14. A router has learned about a network through static and dynamic routing
processes. Which route will be used to reach network 192.168.168.0?
• D 192.168.168.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Ethernet0
• O 192.168.168.0/24 [110/1012] via 192.168.200.1, 00:00:22, Ethernet0
• R 192.168.168.0/24 [120/1] via 192.168.200.1, 00:00:17, Ethernet0
• S 192.168.168.0/24 [1/0] via 192.168.200.1
15. Which three statements are true regarding the encapsulation and de-
encapsulation of packets when traveling through a router? (Choose three.)
• The router modifies the TTL field, decrementing it by one.
• The router changes the source IP to the IP of the exit interface.
• The router maintains the same source and destination IP.
• The router changes the source physical address to the physical address of
the exit interface.
• The router changes the destination IP to the IP of the exit interface.
• The router sends the packet out all other interfaces, besides the one it
entered the router on.
16. When the show cdp neighbors command is issued from Router C, which
devices will be displayed in the output?
• D, SWH-2
• A, B, D
• SWH-1, SWH-2
• B, D
• SWH-1, A, B
• A, B, D, SWH-1, SWH-2
17. Refer to the exhibit. A network administrator is trying to determine why
router JAX has no OSPF routes in its routing table. All routers are configured
for OSPF area 0. From the JAX router, the administrator is able to ping its
connected interfaces and the Fa0/1 interface of the ORL router but no other
router interfaces. What is a logical step that the network administrator
should take to troubleshoot the problem?
• Reboot the routers.
• Change the OSPF process ID on all of the routers to 0.
• Check to see if the cable is loose between ORL and JAX.
• Check to see if CDP packets are passing between the routers.
• Use show and debug commands to determine if hellos are propagating.
18. Using default settings, what is the next step in the router boot sequence
after the IOS loads from flash?
• Perform the POST routine.
• Search for a backup IOS in ROM.
• Load the bootstrap program from ROM.
• Load the running-config file from RAM.
• Locate and load the startup-config file from NVRAM.
19. Refer to the exhibit. What summary address can Router2 advertise to
Router1 to reach the three networks on Routers 3, 4, and 5 without
advertising any public address space or overlapping the networks on
Router1?
• 172.16.0.0/8
• 172.16.0.0/10
• 172.16.0.0/13
• 172.16.0.0/20
• 172.16.0.0/24
20. The network shown in the diagram is having problems routing traffic. It is
suspected that the problem is with the addressing scheme. What is the
problem with the addressing used in the topology?
• The address assigned to the Ethernet0 interface of Router1 is a broadcast
address for that subnetwork.
• The subnetwork configured on the serial link between Router1 and Router2
overlaps with the subnetwork
assigned to Ethernet0 of Router3.
• The subnetwork assigned to the Serial0 interface of Router1 is on a
different subnetwork from the address for
Serial0 of Router2.
• The subnetwork assigned to Ethernet0 of Router2 overlaps with the
subnetwork assigned to Ethernet0 of Router3.
21. Refer to the exhibit. A new PC was deployed in the Sales network. It was
given the host address of 192.168.10.31 with a default gateway of
192.168.10.17. • The PC is not communicating with the network properly.
What is the cause?
• The address is in the wrong subnet.
• 192.168.10.31 is the broadcast address for this subnet.
• The default gateway is incorrect.
• The host address and default gateway are swapped.
22. Refer to the exhibit. The network is running the RIP routing protocol.
Network 10.0.0.0 goes down. Which statement is true regarding how the
routers in this topology will respond to this event?
• Router4 will learn about the failed route 30 seconds later in the next
periodic update.
• Split horizon will prevent Router4 from forwarding packets to the 10.0.0.0
network until the holddown timer expires.
• Router5 immediately flushes the unreachable route from its routing table.
• Router5 will send Router4 a triggered update with a metric of 16 for
network 10.0.0.0.
23. Refer to the exhibit. Which three statements are true of the routing table
for Router1? (Choose three.)
• The route to network 172.16.0.0 has an AD of 156160.
• Network 192.168.0.16 can best be reached using FastEthernet0/0.
• The AD of EIGRP routes has been manually changed to a value other than
the default value.
• Router1 is running both the EIGRP and OSPF routing process.
• Network 172.17.0.0 can only be reached using a default route.
• No default route has been configured.
24. Refer to the exhibit. What is the most efficient summarization of the
routes attached to router R1?
• 198.18.0.0/16
• 198.18.48.0/21
• 198.18.32.0/22
• 198.18.48.0/23
• 198.18.49.0/23
• 198.18.52.0/22
25. What is the purpose of the TTL field within an IP packet header?
• clears an unreachable route from the routing table after the invalid timer
expires
• prevents regular update messages from inappropriately reinstating a route
that may have gone bad
• removes an unreachable route from the routing table after the flush timer
expires
• limits the period of time or number of hops a packet can traverse through
the network before it should be
discarded
• used to mark the route as unreachable in a routing update that is sent to
other routers
26. Refer to exhibit. Given the topology shown in the exhibit, what three
commands are needed to configure EIGRP on the Paris router? (Choose
three.)
• Paris(config)# router eigrp 100
• Paris(config)# router eigrp
• Paris(config-router)# network 192.168.6.0
• Paris(config-router)# network 192.168.7.0
• Paris(config-router)# network 192.168.8.0
• Paris(config-router)# network 192.168.9.0
27. What does RIP use to reduce convergence time in a larger network?
• It reduces the update timer to 15 seconds if there are more then 10 routes.
• It uses triggered updates to announce network changes if they happen in
between the periodic updates.
• It uses random pings to detect if a pathway is down and therefore is
preemptive on finding networks that
are down.
• It uses multicast instead of broadcast to send routing updates.
28. Refer to the exhibit. What two statements are true based on the output
shown? (Choose two.)
• the reported distance to network 172.16.1.0 is 2172416
• 192.168.10.5 and 192.168.10.9 are feasible successors
• neighbors 192.168.10.9 and 192.168.10.5 have auto summary disabled
• router 3 is load balancing traffic to the 172.16.3.0 network across its serial
interfaces
• all interfaces shown on Router3 are in the passive state and will not send
EIGRP advertisements
29. Refer to the exhibit. The network is using the RIPv2 routing protocol. If
network 10.0.0.0 goes down, what mechanism will prevent Router1 from
advertising false routing information back to Router2?
• triggered updates
• poison reverse
• holddown timers
• split horizon
30. What is the function of the OSPF LSU packet?
• used to confirm receipt of certain types of OSPF packets
• used to establish and maintain adjacency with other OSPF routers
• used to request more information about any entry in the BDR
• used to announce new OSPF information and to reply to certain types of
requests
31. Refer to the exhibit. The routers in the exhibit are running the EIGRP
routing protocol. What statement is true regarding how packets will travel
from the 172.16.1.0/16 network to the 192.168.200.0/24 network?
• The router chooses the first path that it learned and installs only that route
in the routing table.
• The router chooses the path with the lowest administrative distance and
installs only that route in the routing table.
• The router chooses the highest routing ID based on the advertised network
IP addresses and installs only that
route in the routing table.
• The router installs all the equal cost paths in the routing table but sends
packets out only one, holding the others
in reserve in case the primary route goes down.
• The router installs all the equal cost paths in the routing table and
performs equal cost load balancing to send
packets out multiple exit interfaces.
32. Refer to the exhibit. A packet enters Router1 with a destination IP of
172.16.28.121. Which routing table entry will be used to forward this packet
to the destination address?
• 172.16.0.0/16 [1/0] via 192.168.0.1
• 172.16.0.0/20 [1/0] via 192.168.0.9
• 172.16.16.0/20 [1/0] via 192.168.0.17
• 0.0.0.0/0 is directly connected, Serial0/0/1
33. Refer to the exhibit. Routers 1 and 2 are directly connected over a serial
link. Pings are failing between the two routers. What change by the
administrator will correct the problem?
• Set the encapsulation on both routers to PPP.
• Decrease the bandwidth on Serial 0/1/0 on router 2 to 1544.
• Change the cable that connects the routers to a crossover cable.
• Change the IP address on Serial 0/1/0 on router 2 to 192.168.0.1/30.
34. Which two router component and operation pair are correctly described?
(Choose two.)
• DRAM - loads the bootstrap
• RAM - stores the operating system
• Flash - executes diagnostics at bootup
• NVRAM - stores the configuration file
• ROM - stores the backup configuration file
• POST - runs diagnostics on hardware modules
35. The network administrator configures the router with the ip route
172.16.1.0 255.255.255.0 172.16.2.2 command.
How will this route appear in the routing table?
• C 172.16.1.0 is directly connected, Serial0/0
• S 172.16.1.0 is directly connected, Serial0/0
• C 172.16.1.0 [1/0] via 172.16.2.2
• S 172.16.1.0 [1/0] via 172.16.2.2
36. Refer to the exhibit. How many routes are both level 1 and qualify for
use as an ultimate route?
•1
•2
•3
•4
•5
•6
37. Refer to the exhibit. All router interfaces are configured with an IP
address and are operational. If no routing protocols or static routes are
configured, what information will be included in the show ip route command
output for router A?
• All of the 192.168.x.0 networks will be in the routing table.
• Routes to networks 192.168.1.0/24, 192.168.2.0/24, and 192.168.3.0/24
will be in the routing table.
• The routing table will be empty because routes and dynamic routes have
not been configured.
• A default route is automatically installed in the routing table to allow
connectivity between the networks.
38. Which three statements about routing protocols are true? (Choose
three.)
• OSPF elects designated routers on multiaccess links.
• RIP does not support classless routing.
• EIGRP supports unequal cost load balancing.
• EIGRP uses broadcast traffic to establish adjacencies with its neighbors.
• RIP does not advertise a route beyond a hop count of 15.
• OSPF can convergence more quickly because it can find a feasible
successor in its topology table when a successor route goes down.
39. Refer to the exhibit. What will happen if interface Serial0/0/1 goes down
on Router1?
• The Dijkstra algorithm will calculate the feasible successor.
• DUAL will query neighbors for a route to network 192.168.1.0.
• Neighbor 172.16.3.2 will be promoted to the feasible successor.
• Traffic destined to the 192.168.1.0 network will be dropped immediately
due to lack of a feasible successor.
40. Refer to the exhibit. Which statement is true concerning the routing
configuration?
• Using dynamic routing instead of static routing would have required fewer
configuration steps.
• The 10.1.1.0/24 and 10.1.2.0/24 routes have adjacent boudaries and
should be summarized.
• The static route will not work correctly.
• *Packets routed to the R2 ethernet interface require two routing table
lookups.
41. A network administrator has enabled RIP on routers B and C in the
network diagram. Which of the following commands will prevent RIP updates
from being sent to Router A?
• A(config)# router rip
A(config-router)# passive-interface S0/0
• B(config)# router rip
B(config-router)# network 192.168.25.48
B(config-router)# network 192.168.25.64
• A(config)# router rip
A(config-router)# no network 192.168.25.32
• B(config)# router rip
B(config-router)# passive-interface S0/0
A(config)# no router rip
42. Which of the following could describe the devices labeled “?” in the
graphic? (Choose three.)
• DCE
• CSU/DSU
• LAN switch
• modem
• hub
43. Which of the following are required when adding a network to the OSPF
routing process configuration? Choose three.)
• network address
• loopback address
• autonomous system number
• subnet mask
• wildcard mask
• area ID
44. The Suffolk router is directly connected to the networks shown in the
graphic and has a default route that points to the Richmond router. All
interfaces are active and properly addressed. However, when the
workstation on network 172.29.5.0/24 sends a packet to destination address
172.29.198.5, it is discarded by the Suffolk router. What can be a reason for
this result?
• The ip classless command is not enabled on the Richmond router.
• The route was ignored if the Richmond router did not include the
172.29.198.0/24 network in its routing updates.
• The Richmond router is in a different autonomous system than the Suffolk
router.
• The ip subnet-zero command was not configured on the Suffolk router.
• The ip classless command is not enabled on the Suffolk router.
45. Refer to the exhibit. When troubleshooting a network, it is important to
interpret the output of various router
commands. On the basis of the exhibit, which three statements are true?
(Choose three.)
• The missing information for Blank 1 is the command show ip route.
• The missing information for Blank 1 is the command debug ip route.
• The missing information for Blank 2 is the number 100.
• The missing information for Blank 2 is the number 120.
• The missing information for Blank 3 is the letter R.
• The missing information for Blank 3 is the letter C.
46. Refer to exhibit. A company network engineer enters the following
commands in the routers:
R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2
R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1
When the engineer enters the show ip route command on R1, the routing
table does not display the static route
to the 10.1.1.0 network. All R1 and R2 interfaces are correctly addressed per
the graphic. What is a logical next
step that the engineer could take in order to make the static route display in
the routing table in R1?
• Enter default routes in R1 and R2.
• Enable the R1 and R2 serial interfaces.
• Configure the static route to use an exit interface instead of a next-hop
address.
• Enter the copy run start command to force the router to recognize the
configuration.
47. Refer to the exhibit. The network administrator is testing network
connectivity by issuing the tracert command from host A to host B. Given the
exhibited output on host A, what are two possible routing table issues on the
network? (Choose two.)
• Router1 is missing a route to the 172.16.0.0 network
• Router1 is missing a route to the 192.168.1.0 network
• Router2 is missing a route to the 10.0.0.0 network
• Router2 is missing a route to the 172.16.0.0 network
• Router3 is missing a route to the 10.0.0.0 network
• Router3 is missing a route to the 192.168.0.0 network
48. What are two tasks that must be completed before two routers can use
OSPF to form a neighbor adjacency?Choose two.)
• The routers must elect a designated router.
• The routers must agree on the network type.
• The routers must use the same dead interval.
• The routers must exchange link state requests.
• The routers must exchange database description packets.
49. Refer to the routing table shown in the exhibit. What is the meaning of
the highlighted value 192?
• It is the value assigned by the Dijkstra algorithm that designates the
number of hops in the network.
• It is the value used by the DUAL algorithm to determine the bandwidth for
the link.
• It is the metric, which is cost.
• It is the administrative distance.
50. Refer to the exhibit. The results of the show ip route command are
displayed in the graphic for Router R2. Which route will be selected for a
packet with a destination address of 10.1.4.1?
• static route to 10.1.0.0/22
• RIP route to 10.1.0.0/23
• RIP route to 10.1.0.0/24
• 0.0.0.0/0 via 192.168.0.1
51. Refer to the exhibit. Packets destined to which two networks will require
the router to perform a recursive lookup? (Choose two.)
• 10.0.0.0/8
• 64.100.0.0/16
• 128.107.0.0/16
• 172.16.40.0/24
• 192.168.1.0/24
• 192.168.2.0/24
52. Which of the following are primary functions of a router? (Choose two.)
• packet switching
• microsegmentation
• domain name resolution
• path selection
• flow control
53. What are three features of CDP? (Choose three.)
• tests Layer 2 connectivity
• provides a layer of security
• operates a OSI layers 2 and 3
• enabled by default on each interface
• used for debugging Layer 4 connectivity issues
• provides information on directly connected devices that have CDP enabled
54Refer to the exhibit. All routers in the network are running RIPv2 and
EIGRP with default routing protocol settings and have interfaces configured
with the bandwidths that are shown in the exhibit. Which protocol will be
used and how will traffic between the Router1 LAN and Router5 LAN be
routed through the network?
• RIPv2 will load balance across both paths between Router1 and Router5.
• EIGRP will load balance across both paths between Router1 and Router5.
• RIPv2 traffic will use the path Router1, Router2, Router5 because it has the
least hops.
• EIGRP traffic will use the path Router1, Router3, Router4, Router5 because
it has the best metric.
55. Which three statements describe the operation of routing with EIGRP?
(Choose three.)
• As new neighbors are discovered, entries are placed in a neighbor table.
• If the feasible successor has a higher advertised cost than the current
successor route, then it becomes the primary route.
• If hello packets are not received within the hold time, DUAL must
recalculate the topology.
• The reported distance is the distance to a destination as advertised by a
neighbor.
• EIGRP maintains full knowledge of the network topology in the topology
table and exchanges full routing information with neighboring routers in
every update.
• EIGRP builds one routing table that contains routes for all configured
routed protocols.
56. Which of the following should be considered when troubleshooting a
problem with the establishment of neighbor relationships between OSPF
routers? (Choose three.)
• OSPF interval timers mismatch
• gateway of last resort not redistributed
• interface network type mismatch
• no loopback interface configured
• administrative distance mismatch
• inconsistent authentication configuration
57. What is the first step OSPF and IS-IS routers take in building a shortest
path first database?
• learn about directly connected networks
• send hello to discover neighbors and form adjacencies
• choose successors and feasible successors to populate the topology table
• flood LSPs to all neighbors informing them of all known networks and their
link states