Scribd
Upload
272 views

ASME VIII Calc - Shell - Heads

The document contains calculations to determine the minimum required thickness of a vessel shell and head according to ASME VIII Division 1 codes. For the shell, the minimum thickness is calculated to be 0.307 inches not at a weld and 0.361 inches at a weld. For the head, the minimum thickness is calculated to be 0.307 inches not at a weld and 0.362 inches at a weld. The corrosion allowance is 0.125 inches for both, resulting in total minimum thicknesses of 0.432 inches for the shell and 0.487 inches for the head.

Uploaded by

Muh Safaat
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
272 views

ASME VIII Calc - Shell - Heads

The document contains calculations to determine the minimum required thickness of a vessel shell and head according to ASME VIII Division 1 codes. For the shell, the minimum thickness is calculated to be 0.307 inches not at a weld and 0.361 inches at a weld. For the head, the minimum thickness is calculated to be 0.307 inches not at a weld and 0.362 inches at a weld. The corrosion allowance is 0.125 inches for both, resulting in total minimum thicknesses of 0.432 inches for the shell and 0.487 inches for the head.

Uploaded by

Muh Safaat
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 4

ASME VIII Division 1, UG-27 Thickness of Shells Under Internal Pressure

Plant ID
Plant
Equipment Number: 1234
Equipment Name:
Chemelectric Treater
Equipment Type:
Vessel
Date:
21st January 2015
Design
Material:
SA 516-70
Year 1970
Nominal Thickness:
0.5 in
Corrosion Allowance: 0.125 in
MAWP:
75 psig
Outside Diameter:
144 in
Design Code:
ASME VIII
P&ID Dwg:
55-007.COL.PI.10-0326
Minimum required thickness of shell (t)
Reference: ASME VIII, Division 1, UG-27 (c)(1)

t=

PR
SE - 0.6P

where
t = minimum required thickness of shell, inches
P = internal design pressure, psi
R = inside radius of shell course under consideration, inches
S = maximum allowable stress value, psi (ASME II, part D, subpart 1)
E = joint efficiency
Not at weld
P=
R=
S=
E=
t=

75 psi
71.375 in
17500 psi
1
0.307 in

At weld
P=
R=
S=
E=
t=

75 psi
71.375 in
17500 psi
0.85

Joint Efficiency for Sp

0.361 in

ASME VIII, Table UW1

Minimum required thickness of shell (t) + corrosion allowance (c)

tm = t + c
where
tm = pressure design wall thickness + c, inches
c = corrosion allowance
Not at weld
t=
ca =
tm =

0.307 in
0.125 in
0.432 in

At weld
t=
ca =
tm =

0.361 in
0.125 in
0.486 in

Joint Efficiency for Spot RT


ASME VIII, Table UW12 (1) (b)

ASME VIII Division 1, UG-32 Thickness of Heads Under Internal Pressure


Plant ID
Plant
Equipment Number: 1234
Equipment Name:
Chemelectric Treater
Equipment Type:
Vessel
Date:
21st January 2015
Design
Material:
SA 516-70
Year 1970
Nominal Thickness:
0.5 in
Corrosion Allowance: 0.125 in
MAWP:
75 psig
Outside Diameter:
144 in
Design Code:
ASME VIII
P&ID Dwg:
55-007.COL.PI.10-0326
Minimum required thickness of head (t)
Reference: ASME VIII, Division 1, UG-32 (d)

t=

PD
2SE - 0.2P

where
t = minimum required thickness of head after forming, inches
P = internal design pressure, psi
D = inside diameter of head, inches
S = maximum allowable stress value, psi (ASME II, part D, subpart 1)
E = joint efficiency
Not at weld
P=
D=
S=
E=
t=

75 psi
143.375 in
17500 psi
1
0.307 in

At weld
P=
D=
S=
E=
t=

75 psi
143.375 in
17500 psi
0.85

Joint Efficiency for Sp

0.362 in

ASME VIII, Table UW1

Minimum required thickness of head (t) + corrosion allowance (c)

tm = t + c
where
tm = pressure design wall thickness + c, inches
c = corrosion allowance
Not at weld
t=
ca =
tm =

0.307 in
0.125 in
0.432 in

At weld
t=
ca =
tm =

0.362 in
0.125 in
0.487 in

Joint Efficiency for Spot RT


ASME VIII, Table UW12 (1) (b)

You might also like