Scribd
Upload
163 views

PID Controller

The mCS 5000 series are single loop PID controllers that can be configured on-site to accept various input types and provide precise control of linear or non-linear processes. Key features include autotuning, universal inputs, optional communication and retransmission outputs, alarms, and cutout sizes. The controllers can be programmed for internal or external setpoints with ratio and bias controls and support P, PI, and PID control modes.

Uploaded by

aharish_iitk
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
163 views

PID Controller

The mCS 5000 series are single loop PID controllers that can be configured on-site to accept various input types and provide precise control of linear or non-linear processes. Key features include autotuning, universal inputs, optional communication and retransmission outputs, alarms, and cutout sizes. The controllers can be programmed for internal or external setpoints with ratio and bias controls and support P, PI, and PID control modes.

Uploaded by

aharish_iitk
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Single Loop PID Controllers

Series
Series :: mCS
mCS 5000
5000
SALIENT FEATURES
6
6
6
6
6
6
6
6
6
6
6
6

Autotuning provided
Universal Input
Communication Port provided optional
Bargraphs / Digital Read-out for deviation, output and set-point
Remote Set Point (Cascade Input) provided
Isolated 4 to 20 mA Control Output
SCR output / Relay output for controlling motorised valves
Optional retransmission output
Two alarms provided on Process Variable, Set-point, Deviation, Output
Built-in two-wire transmitter supply
Various Cutouts and sizes
Single Chip design for ruggedness and low cost

The mCS 5000 series Single Loop PID Controllers are instruments used for precise controlling of various linear /
non linear processes. The same unit can be configured at site to accept inputs from two-wire, three-wire or
four-wire transmitters or temperature sensors. The thermocouples and RTDs are linearised.
The unit can be configured for internal / external set-point with ratio control and biasing facility. Other functions such
as Ramp, Soak, Profile etc. are available on request.
TECHNICAL SPECIFICATIONS
Input

: 1) 4 to 20 mA DC, 0 to 20 mA DC (Input Impedance < 200 ohm)


2) 1 to 5 V DC, 0 to 5 V DC (Input Impedance > 2K ohm)
3) RTD, PT-100, 3 wire
4) Thermocouples J type, K type (others on request) (Input Impedance > 1M ohm)
Range
: Calibrated as per customers requirement from front key pad
Display
: 1) 4 digit, LED for Process Value
2) 4 digit, LED for Set-point, Output
3) 3 digirt, 0.3 LED or 21 segment bargraph for output
Set-point
: Internal / external programmable
Control Output
: 4 to 20 mA in max 600 ohm load (or Relays)
Modes
: Auto / Manual (bumpless transfer provided)
Control Action
: Forward / Reverse programmable
Control Modes
: P+I+D
Proportional Band (P)
: 2% to 1000%
Integral Action Time
(I) : 1 to 9999 seconds
Derivative Action Time (D) : 1 to 9999 seconds
Alarms
: Two alarms provided on Process Variable, Set-point, Deviation, Output
Output Relays
: 1 NO + 1 NC per alarm, rated at 230 V AC, 5 A resistive load
Transmitter Supply
: 24 V DC, 30 mA
Retransmission Output
: 4 to 20 mA (Isolated) optional (max load 600 ohm)
Programming
: All parameters programmable by splash proof front key pad
Accuracy
: < +/- 0.2% of FSD
Supply
: 230 V AC, 50 Hz (others on request)
Mounting
: Flush on panel
Dimensions
: Cutout
Bezel
1) 92mm X 92mm
1) 96mm X 96mm
2) 138mm(H) X 68mm(W) 2) 144mm(H) X 72mm(W)
Depth
: less than 200mm
Operating Temperature
: 0 to 50 deg C
Temperature Coefficient
: 0.015% / deg C
Humidity
: 90% maximum (non-condensing)

NISHKO INSTRUMENTS PVT. LTD.


EI-5, Electrocnic Zone, MIDC Bhosari, Pune 411026.
Phone : 020-27121066, 27127620, 27122304, Fax : 020-27122888
E-mail : [email protected] Web site : www.nishko.com

You might also like