DRILL LIMASTER 3/8 INCH CORDLESS DRILL 12 VOLT ASSEMBLY AND OPERATING INSTRUCTIONS KEYLESS CHUCK KEYED CHUCK PASC ® 23 “TOOLS wii, ———_—_— em 3491 Mission Oaks Bivd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright © 2000 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts, please call 1-800-444-3353ne FB rrr 46443 SKU 46442/ 46443 Page 1Specifications TEM. DESCRIPTION 12 VDC; Speed: 0 to 500 RPM Drill Variable speed switch Forward / Reverse Button 318 inch keyed chuck - Model 46443, 3/8 inch keyless chuck - Model 46442 Torque Settings [1 ~ 15, and Drill 3 ~ 5 hour recharge Battery Charger _| Input voltage: 120 VAC, 60 Hz, 94 mA, Output voltage: 15 VDC, 400 mA, Battery 12 VDC, 1.3 amp-hour (N-Cd) Total Weight 3.55 Lbs. (with battery) Chuck Save This Manual ‘You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram, Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Safety Warnings and Precautions WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this tool! 1. Keep work area clean. Cluttered areas invite injuries. 2. Observe work area conditions. Do not use machines or power tools in damp or wet locations. Don't expose to rain. Keep work area well lighted. Do not use electrically powered tools in the presence of flammable gases or liquids. 3. Keep children away. Children must never be allowed in the work area. Do not let them handle machines, tools, or extension cords. 4. Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children, 5. Do not force tool. It will do the job better and more safely at the rate for which it was intended. Do not use inappropriate attachments in an attempt to exceed the tool capacity. 6. Use the right too! for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. Do not modify this tool and do not use this tool for a purpose for which it was not intended. SKU 46442/ 46443 Page 210. 11. 12. 13. 14. 15. 16. “Le Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if you are producing metal flings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines. : Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and, if damaged, have them repaired by an authorized technician The handles must be kept clean, dry, and free from oil and grease at all times. Disconnect power. Unplug charger when not in use. Avoid unintentional starting. Be sure the switch is in the Off position when not in use. Do not carry any tool with your finger on the trigger. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you are tired Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts. or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if any switch does not turn On and Off properly. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. Take caution as some woods contain preservatives such as copper chromium arsenate (CCA) which can be toxic. When driling these materials extra care should be taken to avoid inhalation and minimize skin contact. Note: Performance of this tool may vary depending on the battery charge level. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be under- stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SKU 46442/ 46443 Page 3Unpacking When unpacking, check to make sure that all parts are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. SP Pnanae Cordless Drill with keyless chuck shown = = Uf, Model 46442 with Keyed chuck (not shown) will also come with chuck key a2 Battery Battery Charger Battery Precautions Read all instructions and warnings on the battery before charging the battery. To avoid accidents, charge the supplied battery only. Do not use a different charger with this battery. Do not expose the battery to rain or wet conditions. To avoid damage of cable and plug, never pull the cable to disconnect the charger. Do not use the charger if the cable or plug are damaged. Repairs should be carried out by a qualified technician only. Do not touch the battery poles with any conductive source, Do not store the battery in a box with other metal objects. Do not throw the battery in a fire. Charging Battery ‘The Battery does not come charged from the factory. Charge before using. Refer to top photos on next page. 1. ae Push the two side buttons in on the Battery, then slide the Battery off the Drill handle. Slide the Battery into the Charger Base. The battery can only insert one way using the guide tabs. Plug the Charger Adapter output cord into the Battery Charger connector. Plug the Charger Adapter line cord into an electrical outlet. SKU 46442/ 46443 Page4Verify on the Charger Base that the green power indicator and the red charging indicator light come on. If they do not come on, check the power connection or try a different wall outlet. Charge the new battery for 8 hours. Subsequent charges will take 3 to 5 hours. Power light (green) 97 J ARR ~ U Caution: The charger will not automatically switch off when the battery is fully charged. The red charging indicator light will remain on. Avoid battery damage by removing power to the charger after the desired charge time. Drill Torque Selector The Torque Selector dial is indicated by the number 1 through 15; Lowest torque: position #1. Highest torque: position #15. For example, position #1 (low torque) is appropriate for driving screws into wood without stripping the screw, but would not provide enough torque for drilling. Position #10 and up (high torque) are appropriate for drilling. Chuck Sleeve Chuck Forward / Reverse Switch Torque Selector Variable Speed Switch Battery Battery Release Buttons SKU 46442/ 46443 Page 5Drill Operation 1. _ Insert drill or screw bit into the Chuck and hand tighten clockwise (with keyless chuck) or use chuck key with keyed chuck. 2. Press the Forward/Reverse Switch to desired position. Fonward position: drill or fasten (clockwise rotation). Reverse position: removing fasteners or freeing bits (counterclockwise rotation), 3. Set the Torque Selector to the desired position. 4. Press (and hold) the Variable Speed Switch to turn drill on. This Switch varies the speed depending on how far in it is pressed. If the clutch ratchet rattles and does not move, use a higher torque setting Avoid overloading the drill. Always use sharpened drill bits. Do not apply excessive pressure to the drill while drilling. If the drill speed drops abnormally, decrease pressure immediately. {f the bit stops abruptly, or the bit becomes stuck, release Switch at once. Removing Battery 1, Press (and hold) on the Battery Release Buttons. 2. Slide the Battery out of the Drill handle. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activites, contain chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: + Lead from lead-based paints + Crystalline cilica from bricks and cement or other masonry products + Arsenic and chromium from chemically treated lumber Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code 25249.5, et seq. ) Maintenance 1. Keep tools clean by wiping with a damp cloth. 2. Store tools in carrying case when not using; avoid storing in high temperature areas. 3. When the battery becomes weak, and the tool loses power, keep the tool tured On until the battery is completely drained before recharging. This will ensure a full recharge. : 4, Recharge battery monthly when not in use to maintain battery life. Using a rag and light oil, wipe drill bits and other steel parts to keep them from rusting SKU 46442/ 46443 Page 6