Isometric Layout

Drawing Isometric Offsets

Calculating Isometric Offsets
Isometric Dimensioning & Labeling

Chapter 8

 An isometric drawing is a type of pictorial drawing in which three sides of

an object can be seen in one view.
Its popular within the process piping industry because it can be laid out
and drawn with ease and portrays the object in a realistic view.
Sometimes it is used in lieu of plans and elevations but typically it is
used to supplement the plan drawings
Isometrics are used as fabrication & shop drawings for pipe run
fabrication
Isometrics also provide a drafter with the ability to calculate angular
offsets in the pipe run.

Isometric Layout:
Isometric lines: one vertical & two at 30 from horizontal

Isometric lines can be measured

Non-isometric lines: lines NOT
parallel to the isometric lines
these lines cannot be measured
Example of isometric axis
You will use the isometric axis on ALL of your isometric drawings!

In the example at left, note that all directions of

the pipe match the three isometric axis lines

Scale:
isometrics are seldom drawn to scale
however, pipe lengths should be shown proportionately
many companies draw isometrics on B-size paper (11 x 17)
which is a limited space so sometimes proportion may be sacrificed
because of the lack of scale in an isometric, its IMPORTANT that
the written dimensions are accurate

Direction & location:

location and direction help to properly orient the isometric drawing
a north arrow give direction and should ALWAYS point to the upper-right
corner of the paper
structural reference points that provide location can be shown on isometric
dimensions MUST always be given to points of reference; such as
structures, existing equipmentetc
coordinates should also be shown on the isometric drawing

Isometric planes:
there are three planes that exist in isometric drawings
with three planes, there are a number of ways for valves and
fitting to be shown

the illustration shown above and on page 218 in your book

shows the planes and possible positions of fittings & valves
remember that if pipes or features are parallel in the piping
layout, they theyll be parallel in the isometric view

Fitting symbols and orientation:

when orienting fittings and
valves its important to know that
there are good methods and
poor methods in this orientation
process

Not ice how the flow of the

isometric is continuous
and provides a clear
picture of the pipe run

the general rule for producing

an isometric using GOOD
techniques, is to draw the fittings
so they are parallel to the last
direction change or branch in the
pipe

Not following the general

rule leads to a chaotic
looking isometric it
doesnt look professional

 fittings are drawn the same shape as they

appear on the plan & elevation drawings
EXCEPT theyre at an isometric angle
elbows can be drawn a couple of ways
check with company standards
In this class we will use square corner
elbows
not only is this the most typical
method used, but its also quicker to
draw.

Curved Elbow Representation

Squared Elbow
Representation

Connected piping:
one run of pipe per isometric
drawing

Example of double-line method

showing existing piping

branches of the pipe run or

continuations are placed on other
drawings typically shown as short
portion of dashed line on main pipe
run
usually a note indicates he
name or specification of the
branch line
existing piping is sometimes shown
using double line method or dashed
lines in this class we will use
dashed lines
either method is useful in that
it distinguishes new pipe from
existing piping

Notice spec change between

new and existing pipe & note
for reference drawing

Pg. 220 text

Dashed line showing pipe

continuation and note providing
reference drawing information.

Isometric drawing techniques:

To increase drawing efficiency:
Create a prototype for isometric drawings
set up grid, snap, isometric plane orientation, border and
title block, BOM, text styles & dimension settings
Develop library of isometric symbols
valves, fittings, instruments, equipment common
drawing components
Create dimension styles in all three isometric planes
Construct menus that you can pick symbols from

Drawing Isometric Offsets:

Offset:
indicates that a piece of pipe is shifted from one line of direction to another
is done with a fitting (typically a 45 elbow)
one of the few times you might have artistic license in making a piping
drawing
Horizontal offsets:
If you draw a horizontal pipe with a 45
elbow running form southeast to
northwest technically correct, it would
look like a vertical line to prevent
confusion, the offset is drawn 22
from vertical to give the illusion of the
angle.

Thats why many companies use a squaringin plane within the plane of the offset

Vertical Offsets:
These offsets can get just as confusing as the horizontal
offsets. Using the same techniques; 22 and the squaring
in planes help remedy the visualization of these offsets as
well.

FYI: As a drafter, you should always be aware of some of the

confusing qualities inherent to isometric piping drawings and
take measures to ensure the drawings are easily understood.

Calculating Isometric Offsets

Although you can get away with an educated guess as to making an angular offset
easy to see when laying out an isometric, you cant make a guess-ti-mate when it
comes to determining pipe lengths and angles.
So, pull out the old calculator, paper, pencil & a BIG eraser and lets get started.
The basic calculations any pipe drafter uses are those involving
trigonometry and right angles.
Pythagoras, a 6th century B.C. Greek philosopher, came up
with a way to deal with calculations involving right angles
and its called the anyone? . Anyone???
Pythagorean Theorem
Simply, what Pythagoras concluded was that when working
with right angle triangles the square of the hypotenuse is
equal to the sum of the squares of the two sides.
c = a + b

Example: Pythagorean Theorem (p. 223)

1. Start off with whats given or what you can determine
from the pipe drawing itself.
a) We are given an 45 angle rise, that clues us in
on the fact that the two sides of our triangle are
going to be the same length
b) By doing simple subtraction, we can come up
with the length for side B: 11-9 6-3 = 5-6
OR you can subtract the elevations given
and get the same dimension for side A.
c) Since B = A: side A = 5 -6 as well.
2. Now all you have to do is plug the
numbers into your formula:
a) c = (5 -6 ) + (5 -6 )
BREAKING DOWN THE NUMBERS:

b) c = (5.5208) + (5.5208)

FYI: 5 -6 = 5.0 ft.

c) c = 30.4792 + 30.4792
6 = 6/12 = .5 in.
= .25/12 = .0208 in.

= 5.5208 ft.

d) c = 60.9584
e) c = 60.9584
f) c = 7.8075
g) c = 7 -9 11/16

SMOLEYS TABLES:
Before there were calculators there was Constantine K. Smoley, an
educator and civil engineer.
Smoley published a book in 1901 that became the bible for any
professional (engineers and architects) or student that needed to be
able to calculate squares, square roots, logarithms & trig functions.
If we had used the Smoleys Tables to solve the
previous problem:
1. We would have flipped through the pages to
find 5
2. Then we would look for 6 column heading
3. Then in the far left column we would have
looked down to find the row labeled
4. At the intersection of the Square column under
6 and the Row, wed find the square for 56 given in decimal form 30.4796
a) c = 30.4796 + 30.4796
b) c = 60.9592
c) c = 60.9592
d) c = 7.8076

TRIG function formulas:

There are three basic trig function formulas that are frequently used in piping:
SIN = SO/HYP
COS = SA/HYP
TAN = SO/SA
When angle A is used, a is the side opposite (SO) and b is the side adjacent (SA).
When angle B is used, a is the side adjacent (SA) and b is the side opposite (SO).

Get familiar with the formulas for

solving angles and lengths in piping
offsets.

Table on page 227 in your text.

Solving Compound Angles:

When piping has to be snaked through equipment, steel, conduit and other pipe,
the pipe may be rolled along with the offset. This type of piping design is called a
rolling offset and forms a compound angle.

Four terms associated with a rolling offset configuration:

RUN: Length of total offset in direction of pipe run
SET: Depth of offset
ROLL: Breadth of offset
TRAVEL: True length of pipe through offset

FYI: Separate tutorial Working with Offsets

provides in depth detail of solving for lengths of
pipe and angles itll come in handy with some
assignments!

Isometric Dimensioning & Labeling

Two planes are used in dimensioning and labeling-horizontal and vertical.
DIMENSIONING PRACTICES:
1. Best way to dimension a pipe is to its
centerline at the intersection point
2. Try to keep all dimensions outside the
piping view when possible
3. Dimensions should ALWAYS be shown
between points in the same plane
4. One of the extension lines of the
dimension should be a centerline of the
run of pipe
5. Vertical lines of text should always be
parallel with extension lines

Isometric lettering:
Basic guidelines for lettering isometric
drawings:
1. If the pipes vertical, the lettering should
be written vertically and at 30 angle
2. If pipe is in horizontal plane, the lettering
will appear as if it is lying down and will be
oriented on both 30 angles
3. Dimensions appear to be lying down if the
pipe is horizontal or standing on end if the
pipe is vertical.