IJRET: International Journal of Research in Engineering and Technology

eISSN: 2319-1163 | pISSN: 2321-7308

OPTIMIZATION OF TRIETHYLENE GLYCOL (TEG) DEHYDRATION

IN A NATURAL GAS PROCESSING PLANT
Nmegbu Chukwuma Godwin Jacob
Department of Petroleum Engineering, Rivers State University of Science and Technology, Port Harcourt

Abstract
In optimizing glycol dehydration system for the natural gas processing, several critical parameters that can be varied to achieve
specific dew point depression exist. From HYSYS simulation, a gas plant was placed under investigation with the aim of studying
the effects of variation in glycol flow rates, number of stages (4, 8 and 12 trays) of the absorber, reboiler temperature ( 180oC,
190oC and 200oC) and stripping gas rate on the water content of the gas in a glycol dehydration unit in the Niger Delta. Results
show that an increasing reboler temperature above 200 oC led to the thermal decomposition of glycol and introduction of
stripping gas had a significant effect than increasing the reboiler temperature. Also, the design of the TEG system was adequate
to achieve a dew point of about 5oC at 95bars. This study therefore seeks to proffer solutions for the optimization of the Niger
Delta gas plant dehydration process using the HYSYS simulator.

Keywords: Dehydration, Glycol, Optimization TEG..

--------------------------------------------------------------------***---------------------------------------------------------------------1. INTRODUCTION

2. MATERIALS AND METHODS

Natural gas is a combustible mixture of hydrocarbon gases

and a vital component of the worlds supply of energy. It is
one of the cleanest, safest and most useful of all energy
sources, formed primarily of methane, ethane, propane,
butane and pentane [1]. In Its processing, the presence of
water it poses a great problem and vapors of its water
content can lead to hydrate formation at low temperatures
and high pressures and/or corrosion when it is in contact
with hydrogen sulphide (H2SO4) and carbon dioxide (CO2)
components which are all present in the gas stream [2]. The
removal of the water vapor that exists in these natural gases
requires a complex treatment consisting of treatments with
varying degrees of efficiency involving gas dehydration
processes [3]. Glycol dehydration is the most common
dehydration process used to attain pipeline sales
specifications and field requirements [2], [4]. [5]. For this
process, a liquid desiccant dehydrator serves to absorb water
vapor from the gas system within the contactor. This
desiccant having glycol as its principal agent has the
chemical affinity for water, stripping most water content of
the travelling gas stream. Regeneration of this glycol occurs
in a specialized reboiler designed to vaporize only the water
from the solution [6]. For the past few years, the design of
glycol plants utilizes the rule-of thumb procedures. The
problem of pigging in export plants reveals a significant
wall thickness loss up to about 36% at some points in
pipeline systems.[4], [6], [7] Presence of water in these
systems in reaction with CO2 can cause corrosion. Routine
pigging assessment showed that 4 - 9% of the liquid
recovered from plant in the Niger Delta spur of the gas
transmission system (GTS) as free water. This research is
aimed at optimizing gas plant dehydration systems to meet
the specified sales of gas-water dew point requirements of
5oC at 95bar.

2.1 The Contacting Unit (HPLT)

A glycol contactor is divided into two sections, the smaller
lower section known as the scrubber section (integral
scrubber) and the larger upper section known as the absorber
section consisting of a wire mesh mixed extractor and
separation of these two trays is done by installing a special
section called the Chimney tray. The wet inlet gas stream
enters the integral scrubber tangentially through the gas inlet
for centrifugal separation of liquid accumulation and then
passes through the high capacity, high efficiency mist
extractor for extra trapped liquid contents. The gas stream
undergoes several processes before it comes in contact with
the glycol liquid flowing counter-currently down the
column. As the gas passes through the trays water is
absorbed by these glycol from the gases until the gases
become extremely dehydrated. Incoming glycol from surge
tanks is cooled in a heat exchanger before it enters the top of
the contactor through the contactor vessel by passing across
the trays, stripping more water till it becomes increasingly
enriched with water during the counter flow. Operating
efficiency of these contactors depends on the gas flow rate,
temperature, pressure and also on the lean glycol
concentration and its circulation rate.

2.2 The TEG Regeneration Unit (HTLP)

This unit is conditioned with removal of dissolved gases,
liquid hydrocarbon, solids and water from the glycol. Rich
glycol leaves the contactor and reaches the lean-rich glycol
heat exchanger to warn the glycol in order to its viscosity
and accelerate glycol-liquid-gas separation in the flash
drum, proceeding to the cartridge filters solid particles are
removed to prevent plugging in heat exchangers foaming,
pigging/fouling, cell corrosion and hot spots on the fire
tubes downstream of the cartridge filters. The cooled filtered

_______________________________________________________________________________________
Volume: 03 Issue: 06 | Jun-2014, Available @ http://www.ijret.org

346

IJRET: International Journal of Research in Engineering and Technology

glycol solution is routed through shell side of the HE to
warm the glycol in order to reduce fuel consumption in the
reboiler before entering the Still Column which operates at
atmospheric pressure mounted on the reboiler at a fixed
point. Glycol flows downward through the still column
towards the reboiler contacting hot glycol vapor, water
vapor and stripping gas. The temperature control (heater) in
the reboiler operates a fuel gas motor valve to maintain the
proper temperature in the glycol to reduce potential glycol
degradation at about 374 oF on the condition that TEG
decomposes at a temperature of 404oF. After a series of
other glycol purification process, stripping gas is added to
the reboiler to provide extra-dry glycol. TEG recovered
from the reboiler which also increases glycol concentrations
by providing counter-current contact of the glycol and the
stripping gas.. hot regenerated glycol passes through a tube
from the stripping column to cool thereby increasing its
absorption capacity and its tendency to flash in the
contactor.

2.3

Model

Formulation

Optimum

Operation

(Design of the Dehydrating Unit)

The following steps are requisite for the proposed design;
1. Obtain design information.
2. Select an appropriate combination of lean glycol,
circulation rate absorber trays or packing balance.
3. Establish the required balance i.e material balance,
energy balance.
The maximum and minimum gas flow rates were taken into
account, among others are the gas composition and expected
water dew point/ water content of the outlet gas. Obtaining
the above parameters, the minimum concentration of TEG in
the lean solution entering the top of the absorber required to
meet outlet gas water specification. The required lean TEG
rate needed to pick-up the necessary amount of water from
the gas to meet the outlet gas water content specification.
Also, the amount of absorber contact required to produce the
necessary equilibrium in the above at any circulation rate
will be considered. Other important considerations such as
safety, utilities and environmental regulations for
discharging stripper overhead are also evaluated.

2.4 Process Simulation of Gas Plant-X using

HYSYS
This study analyses the results of a plant simulation
performed using the HYSYS simulator. This all-purpose
simulator incorporates objective oriented programing
techniques to provide an objective linking and embedded
(OLE) technology responsible for creating a common
interactive interface between HYSYS and other
applications. Also providing increased functionality
framework in integrating a broad range of technologies
under a common look and feel. This simulator offers a
unique attribute to support the implementation and solution
of a wide range of applications in the chemical,
petrochemical, oil and gas industry.

eISSN: 2319-1163 | pISSN: 2321-7308

3. RESULTS AND DISCUSSION

In order to investigate the important design variables, we
obtained plots or residual water content versus circulation
rates and they were presented. Among the plots made were
for common values of such parameters like numbers of trays
in the contactor, glycol circulation rate through the
contactor, temperature of the recoiled in the regenerator and
the amount of stripping gas used.

3.1 The Effects of Number of Equilibrium Stages in

the Absorber
Figure 1 illustrates the effect of the number of equilibrium
contact trays on residual water content using a 200oC
reboiler. Fig 2 presents a similar response comparing the
dew point dispersion in place of actual water content.
Increasing water content allows the gas to attain equilibrium
with the lean circulation rate. Considering a typical glycol
circulation rate of approximately 3galTEG/lb of water
removed, fig 1 and 2 illustrates that a 12 tray contactor is
virtually in equilibrium with the inlet glycol. For an 8-tray
contactor a circulation rate of about 5 6 gal TEG/lb water
could be required to attain equilibrium.

3.2 Effects of Reboiler on Temperature

Increasing reboiler temperature to 204oC will result in a
thermal decomposition of TEG. Even at 200 oC reboiler,
glycol decomposition can occur due to higher film
temperature and as such, temperature of about 180 oC, 190oC
and 200oC were simulated Fig 3, 4 and 5 illustrates the
overhead water content using a fixed number of trays at
reboiler temperatures of 180oC, 190oC and 200oC for 8 or 12
contactor contactor trays, pipeline quality gas containing
less than 71lb water/MMSCF gas could be produced using
either the 190oC or 200oC reboiler temperature. At 190oC
approximately 4.5gal TEG/lb water circulation would be
needed with 8-tray contactor as opposed to approximately
2gal TEG/lb-water with 12-tray contactor. Similarly, at
200oC, approximately 3gal TEG/lb water circulation would
be needed with 8-tray contactor as opposed to 1.5gal TEG/lb
water with 12-tray contactor, noting that the deduced results
for the gas inlet temperature of 35, 36, 37, 38 and 39 oC were
also carried out. This gave a temperature differential ( lean
glycol temperature inlet gas temperature) for 3oC. reboiler
temperature influences the overhead water content by
changing the purity of the lean glycol. Glycol purity values
of 96.0, 97.0 and 98.0wt% were obtained at 180oC, 190oC
and 200oC respectively at pressure of about 1atm.

3.3 Effects of Stripping Gas

Applications requiring high dew point depressions will
always utilize stripping gas in the regenerator. A low dew
point cannot simply be achieved by using the minimum 98%
obtainable with 200oC reboiler temperature at atmospheric
pressure. These low dew points will require up to 99.99wt%
glycol in the absorber. Stripping gas poses a much greater
effect than just increasing reboiler temperature. For a
maximum efficiency, stripping gas must be introduced in a

_______________________________________________________________________________________
Volume: 03 Issue: 06 | Jun-2014, Available @ http://www.ijret.org

347

IJRET: International Journal of Research in Engineering and Technology

short column after the hot glycol is removed in the reboiler.
They may be placed directly in the reboiler but high water
partial pressures in the vapor phase limits its mass transfer
driving force. Fig 6 and Fig 7 illustrates the stripping gas
effects on the residual water content and dew point
depression of the dry gas. As seen, at a small stripping gas
rate of 1sc/gal circulation rate, dry gas will contain about
half the water of the same process without stripping gas.
Increasing the stripping gas rate beyond 2 - 3scf/gal will
have a minimal impact on the dew point depression.
Table 1 Deduced Values for water content and circulation
rates for 4, 8 and 12 trays
Outlet
gas
water
content
(lb/MMSCF)
TEG
rate(gal/lb
water)

N=4

N=8

N = 12

7.6

9.4

7.2

9.6

5.2

5.0

10

5.2

5.0

5
4

11
12

5.2
5.8

5.0
5.0

14

7.0

5.0

19

9.0

6.0

1.5

23

11.2

7.5

13

9.0

eISSN: 2319-1163 | pISSN: 2321-7308

Table 2 Deduced dew point depression for 4, 8 and 12 trays

Dew point depression (oC)
TEG
rate(gal/lb
water)
7.6

N=4

N=8

N = 12

7.2

14.16

22.50

23.06

13.33

522.10

23.06

11.94

21.589

22.89

10.00

20.88

22.77

7.778

19.44

22.50

3.889

16.389

21.38

1.5

0.2778

12.77

18.89

10.00

16.38

14.444

1.25

1.25

0.6

7.50

dew point depression (C)

25

N=4

20

N=8

15
10
5
0
0

0.6

10

15
TEG circulation rate (gas/lb-water)
Fig 2 Effects of the number of contactor trays on the dew
point depression of natural gas with reboiler temperature
200oC
Table 3 Overhead water content using a Fixed number of
contactor trays at different rebioler temperature (4 trays)
Outlet
gas
water content
(lb/mmscf)
TEG
Treb
Treb =190oC
Treb= 200oC
o
rate(gal/lb
=180 C
water)

Fig 1 Effects of number of equilibrium stages in the

contactor on water content of a stream of natural gas with
reboiler temperature of 200oC

7.6

11.8

10

12

10

9.2

12.7

11

10.2

14

12

11.1

15.7

14

12.8

_______________________________________________________________________________________
Volume: 03 Issue: 06 | Jun-2014, Available @ http://www.ijret.org

348

IJRET: International Journal of Research in Engineering and Technology

Table 5 Overhead water content using a Fixed number of

contactor trays at different rebioler temperature (12 trays)
Outlet gas water content(lb/mmscf)

17.8

16

15

21.5

20

19

1.5

25

24

23.6

Treb
=180C

water content (lb

water/MMscf)

25

Treb
=190C

20
15
10
5
0
0

TEG circulation rate (gal/lb-water)

Fig 3 Water content of a natural gas stream heated by a 4tray contactor
Table 4 Overhead water content using a Fixed number of
contactor trays at different rebioler temperature (8 trays)
Outlet gas water content (lb/mmscf)
TEG
Treb
Treb =190oC Treb=
o
rate(gal/lb
=180 C
200oC
water)
7.8
8.2
7.5
8.22
6.8
7.2
8.3
6.82
5.35
6.0
8.5
6.95
5.5
5.0
8.8
7.0
5.65
4.0
9.0
7.4
6.0
3.0
9.8
8.0
6.85
2.0
11.5
9.5
8.45
1.2
14.8
13.4
12
Treb=180

14

Treb=190

12

Treb=200

water content

16

10
8
6

TEG
rate(gal/lb
water)

Treb
=180oC

7.8

8.0

7.4

6.2

7.2

6.2

5.0

6.25

5.0

6.25

5.0

8.15

6.4

5.1

8.3

6.52

5.25

8.89

7.1

5.7

1.6

9.5

7.6

6.7

Treb
=190oC

Treb=
200oC

10
water content (lbwater/MMSCF)

30

eISSN: 2319-1163 | pISSN: 2321-7308

8
6
4

Treb =180C

Treb =190C
Treb= 200C

0
0

5
10
TEG ciculation rate (gal/lb-water)
Fig 5 Water content of a natural gas stream heated by a 12tray contactor
Table 6 Deduced values showing the effects of stripping gas
rate on water content and glycol circulation rate
Outlet gas water content (kg/h)
TEG
rate(gal/mmscf)

0scf/gal

1scf/gal

3scf/gal

6scf/gal

6.6

5.35

2.1

1.4

0.9

5.4

2.2

1.5

5.5

2.5

1.7

1.1

3.0

1.5

6.8

2.8

2.2

8.5

5.5

4.7

4.5

1.2

13.0

10.5

12.4

11

11

2
4
6
8
10
TEG circulation rate (gal/lb-water)
Fig 4 Water content of a natural gas stream heated by a 8tray contactor

_______________________________________________________________________________________
Volume: 03 Issue: 06 | Jun-2014, Available @ http://www.ijret.org

349

water content (lb-water/mmscf)

IJRET: International Journal of Research in Engineering and Technology

14

0scf/gal

12

1scf/gal

10

3scf/gal

6scf/gal

6
4
2
0
0

2
4
6
8
TEG circulation rate (gal/lb-water)
Fig 6 Effects of stripping gas rate on water content of
natural gas streams
Table 7 Relationship between dew point depression and
stripping gas rate
Stripping
gas
rate Dew point depression (oC)
(gal/mmscf)
6
32
3.2
30
1
26
0
18

35
Dew point depression (C)

30
25
20
15
10
5
0
0

Strpping gas rate (scf/gal TEG)

Fig 7 Effects of stripping gas on dew point depression

4. CONCLUSIONS
The design review involved a review of the TEG
dehydration systems generally and in comparison to the
proposed design, the Niger Delta plant is adequate and
robust enough to condition the gas to comfortably achieve a
water dew point of 5oC at 95bar. It is highly recommended
that regular inspection of glycol contactor internals are
conducted at intervals so as to check components of the
system if they are in good condition and still operates
properly. Also regular dew point measurements and
validation from the moisture analyzers installed on the gas
processing trains will be a lot easier with reverse

eISSN: 2319-1163 | pISSN: 2321-7308

calculations using HYSYS. Operational review process

involved spot checks of key process parameters in the TEG
dehydration systems and plant is operated in a satisfactory
manner within the design envelop.

NOMENCLATURE

GTS
HPLT
LPHT
Treb

Triethylene Glycol
Gas Transport Systems
High
Pressure
Low
Low Pressure High Temperature
reboiler Temperature

Temperature

ACKNOWLEDGEMENTS
The author highly appreciates the insurmountable efforts of
Daniel Dasigha Pepple and Ohazuruike V. Lotanna in the
fruitiness of this Study. Among other Such as Family,
Friends and colleagues highly recognized.

REFERENCES
[1]. Arnold, K and Stewart, M. Surface Production
Operations, Vol 2, Design of Gas Handling Systems and
Facilities, 1999.
[2]. Lyons, W. C.: Standard Handbook of Petroleum and
Natural Gas Engineering, Vol. 3, 1994
[3]. Katz D.L Handbook of Natural Gas Engineering,
Production and Storage , McGraw-Hill Book Co., Inc
1990.
[4]. Hernandez, V., Hainvinka, M. W. and Bullin, J. A.:
Designing Glycol Units For Maximum Efficiency. Bryan
Research and Engineering, Inc. 2001
[5]. Campbell, J. M.: Gas Conditioning and Processing
Vol 2, Campbell and Company 2001.
[6]. McLeod, W.R : Prediction and control of natural gas
pipeline. SPE8137 presented at the European offshore
petroleum conference and exhibition in London 24-27
October, 1978, pp.1-8
[7]. Rossi, L.F. and Gas paretto, C. A .1991 Prediction of
hydrate formation in natural gas system, paper SPE 22715
presented at the 66th Annual Technical Conference
exhibition of the SPE held in Dallas, TX ,October 69,1991.pp. 1-7..
[8]. Sloan, E.D. Natural gas hydrate, SPE 23562, Journal
of Petroleum Technology, 1991. pp 1-4.
[9]. Ikoku, C. U Natural gas Engineering Pennwell
Publishing Company, Tulsa, Oklahoma 1980
[10]. Bhangole, A. Y. , Zhu, T., Mc Grail, B. P. and White,
M. D. 2006 A model to predict gas hydrate equilibrium and
gas hydrate in the process media including mixed CO2
CH4 Hydrates, paper SPE 99759 paper presented at the
2006 SPE/DOE symposium on improved oil recovery held
in Tulsa, Oklahoma,22-26,April 2006, Pp. 1-7.

_______________________________________________________________________________________
Volume: 03 Issue: 06 | Jun-2014, Available @ http://www.ijret.org

350