48-71 Steering Column Remove & Install PDF
Uploaded by
mefisto06c48-71 Steering Column Remove & Install PDF
Uploaded by
mefisto06cSteering column, removing and installing
Page 1 of 14
48-71
Steering column, removing
and installing
The steering column is supplied as an assembly
through the Parts Department. The steering
column is serviced by replacement only.
The ignition lock from the faulty steering column
can be refitted page 48-82 .
WARNING!
Before removing the steering wheel:
Observe all safety precautions before
starting work on any part of the airbag
system
page 48-62 .
Disconnect the battery Ground (GND)
strap.
With wheels in the straight-ahead position,
unplug the single-pin connector for the
airbag system power supply.
Non compliance with the above can cause
failure of the airbag system.
Notes:
Removing and installing driver's-side airbag unit
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
Steering column, removing and installing
Page 2 of 14
page 48-64 (for sport steering wheel
48-68 ).
page
Check Diagnostic Trouble Code (DTC) memory
for the airbag system before unplugging the
single-pin connector:
Repair Manual, Body On Board Diagnostic
(OBD), Repair Group 01
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
Steering column, removing and installing
Page 3 of 14
48-72
The red single-pin connector for the airbag system power supply is
located on the right behind the instrument panel cover.
- Open front passenger door, remove cover and disconnect single-pin
connector.
- Unbolt airbag unit from behind at left and right sides of steering wheel
using T30 Torx bit.
Tightening torque: 7 Nm (62 in. lb)
WARNING!
Always observe the safety precautions for airbag systems when
performing any work on the components of the airbag system
Repair Manual, "Body Interior," Repair Group 69 and
Repair
Manual, "Body On Board Diagnostic (OBD), Repair Group 01.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
Steering column, removing and installing
Page 4 of 14
48-73
- Carefully fold back airbag unit.
- Disconnect harness connector from airbag unit and place airbag unit
aside.
- Unbolt steering wheel; when doing this, make sure that spiral spring is
not twisted.
- Remove storage shelf on driver's side:
Repair Manual, Body Interior, Repair Group 70
- Remove steering column switch together with trim:
Repair Manual, Electrical Equipment, Repair Group 94
- Remove all tie wraps (arrows) and disconnect harness connectors.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
Steering column, removing and installing
Page 5 of 14
48-74
Disengaging lock cable
On vehicles equipped with an automatic
transmission, the lock cable must be
disengaged:
- Place transmission selector lever in Park
position.
- Turn ignition key to position -B- (ignition ON).
- Lift locking clip -1- slightly and remove Bowden cable -2- from steering
lock housing.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
Steering column, removing and installing
Page 6 of 14
48-75
Securing steering column prior to removal
- Route safety wire through hole in bottom part of steering column
(arrow) and spring to secure top and bottom parts of steering column
before removing steering column from steering gear pinion.
The steering column can also be secured with a transportation safeguard
page 48-76 .
CAUTION!
The splines between the top and bottom parts of the steering
column must not be separated. If the two halves are separated
and reassembled with the splines no longer in their original
installed positions a rattling noise may result.
Turn the steering wheel to the center position and do not alter
position during repairs, otherwise the airbag unit spiral spring
may be damaged.
- Unscrew nut -1- at universal joint.
- To release eccentric, turn bolt (Torx
T50) clockwise and remove.
- Remove universal joint from steering gear pinion.
- Remove socket head bolts -1- (
remove steering column.
illustration A48-0075 above) and
Removing and installing steering lock housing
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
page 48-82 .
11/20/2002
Steering column, removing and installing
Page 7 of 14
48-76
Installing
1 - Locking clip
2 - Plastic rod
3 - Steering column
New replacement steering columns are supplied with a transportation
safeguard installed. This safeguard must be removed after installing the
steering column in the vehicle.
Note:
It is recommended to save the transportation safeguard components for
subsequent steering column removals.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
Steering column, removing and installing
Page 8 of 14
48-77
Installing
- When installing steering column, always make sure that cap -1- is
installed.
CAUTION!
Cap -1- must always be reinstalled or retrofitted, otherwise the
electrical wiring may become chafed.
- Mount steering column onto crossmember with four socket-head bolts 1-.
- Attach universal joint to steering gear pinion.
- Insert clamping bolt (Torx T50) through bottom part and engage by
turning counterclockwise. Install nut + washer and tighten to 40 Nm (30
ft lb).
CAUTION!
The splines between the top and bottom parts of the steering column
must not be separated. If the two halves are separated and
reassembled with the splines no longer in their original installed
positions a rattling noise may result.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
Steering column, removing and installing
Page 9 of 14
48-78
Engaging lock cable on vehicles with
automatic transmission
Ignition key must be in position -B- (ignition ON) to engage lock cable
- Move selector lever to park position.
- Insert lock cable -2- into steering lock housing.
- Make sure locking clip -1- engages.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
Steering column, removing and installing
Page 10 of 14
48-79
Checking function of lock cable
Applies only to vehicles with automatic
transmission.
- Turn ignition key to position -B- (ignition ON).
It must be possible to move selector shift lever smoothly out of
Park position
It must only be possible to remove ignition key with selector lever
in Park position
- Move selector lever to park position.
Ignition lock must function smoothly
It must not be possible to move selector lever with ignition key in
position -A- (ignition OFF). Ignition key can be removed
Lock cable, removing, installing and adjusting:
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 37
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
Steering column, removing and installing
Page 11 of 14
48-80
Installing, continued for all vehicles
- Remove safety wire between top and bottom parts of steering column.
- Install steering column switch with trim:
Repair Manual, Electrical Equipment, Repair Group 94
- Align steering column relative to trim and make sure joints (gaps) are
even.
- Tighten socket-head bolts -1-.
Tightening torque: 22.5 Nm (17 ft lb)
- Install storage shelf on driver's side:
Repair Manual, Body Interior, Repair Group 70
- Install steering wheel and airbag unit:
Repair Manual, Body Interior, Repair Group 69
WARNING!
Make sure that no person is in the vehicle when re-connecting the
battery Ground strap.
Observe all safety precautions (
Repair Manual, Body Interior,
Repair Group 69 ) whenever working on an airbag equipped
vehicle.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
Steering column, removing and installing
Page 12 of 14
48-81
Steering column, checking for damage
Determining if steering column must be replaced
following an accident:
Visual check
- Check all steering column components for
damage.
Functional check
- Make sure steering column turns easily without
jerking.
- Make sure steering column can be adjusted for
height and reach.
- Check gap (dimension -A-) between slide and mounting bracket.
If dimension -A- is larger than 0.5 mm (0.20 in.), steering column is
damaged and must be replaced
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
Steering column, removing and installing
Page 13 of 14
48-82
Steering lock housing, removing and
installing
WARNING!
Before removing the steering column, make
sure the wheels are in the straight-ahead
position.
Observe the safety precautions for working
on airbags page 48-62 .
Non compliance with the above can cause
failure of the airbag system.
- Remove steering column
page 48-71 .
Notes:
The steering column must be removed and
clamped in a vise to chisel off the shear bolts. If
the shear bolts are chiseled off with the steering
column installed the steering column mounting
bracket will be damaged.
Do not clamp the steering column in a vise at
the mounting bracket otherwise the plastic
coating will be damaged.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
Steering column, removing and installing
Page 14 of 14
48-83
Chiselling open shear bolts
Shear torque of new bolts is
20 Nm (15 ft lb).
- Make sure that cap -1- is installed to avoid risk of chafing electrical
wiring when installing.
- Remove lock cylinder:
Repair Manual, Electrical Equipment, Repair Group 94
- On vehicles with automatic transmission, disengage lock cable
48-74 .
page
Installing
- Install new shear bolts.
- Tighten shear bolts until head shears off.
- On vehicles with automatic transmission, engage lock cable
48-78 .
- Check function of lock cable
page
page 48-79 .
- Install lock cylinder and ignition switch:
Repair Manual, Electrical Equipment, Repair Group 94
- Make sure turn signal lever is in neutral position (to avoid damaging
reset cam of switch) and install steering wheel.
- Install airbag unit
page 48-64 .
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.48.11
11/20/2002
