Conca O Thread gauges page 5-23 ‘ Plain gauges for cylindrical fits, ‘taper- and gear toothing gauges, 1 measuring plug gauges page 25 - 46 ‘ Bevel-edged straight edges, 2 bevel-edged squares page 47 - 53 ‘ Fixtures, 3 special gauges page 55 - 59 ‘ 4 Inspection service page 61 - 63 ‘Thread Gaugesww Thread Gauges The perfect inspection of interchangeable ‘and unconditionally combinaing threads is ensured by uso of thread lt gouges Exteinal and internal threads corespond to the standard if they are found to be tolerance when inspected with theed lint gauges according to the stander. rin) thread gaug As far as cambinatng capability is concemed a thread depends on 4 deternining ses © Exemal diameter + Effect (aso pitch ~ or fank -| diameter © Minor derneter # Bich © Halt ange Since effective diameter, half angle and pitch depend geometrically on each ather eros of the pitch and of the half ange abvays become cerceptibe atthe combination of extemal and intemal threads in the effective ameter (mating flank ciameter), According to the prnciple of Taylor the GO-gauges ae carried out always withthe ful profile (form-ieal counteriece), The length of the thread of GO-gauges should amount to at lest 80% of the screw-in length of the thread combination to recagnie pitch eros For the efficient inspection of thveads in the practice are requred: 1. For the internal thea Limit thread plug gauges 2.For the exter thread Limit tread caliper gauges 60 and NG GO thread ring gauges 4. For the setting of tread ima caliper gauges: Limit thresd setting gauges 4. For wear inspection an thread ring gauges: \Wear inspection plug gauges 6. For the inspection ofthe minor diameter on internal threads: Pin pug gauges Thanks tothe introduction of the metric 'SO-tvead the interchangeably ofthe metric threads is ensured. The O-system for thread tolerances provides several ‘ualies for tolerances of the mejor cameter, ofthe effective dmeter and ofthe minor diameter (DIN 13, Sheets 14 and 15) To reduce the numberof gauges and tools it is recommended to preferably use tolerance zones 38 per Table 5 and 6 according to DIN 13, Sheet 14, Te folowing table shows for scren-in group N the standardized fine aed medium ‘coarse tolerance zones forthe tolerance classes fine. medium and coarse, The marked feds should be preferred IF the tolerance zones forthe effective diameter and the major diameter ofthe extemal thread or the effective diameter and the minor diameter ofthe intemal thread are equal itis not necessary to repeat the spectication ofthe tolerance zone, sample: M126H —Toerrce zon forthe efeche and he minor dee For diferent tolerances of the effective cdameter and ofthe major dameter on ‘extemal thes, minor diameter on interned threads respectively MI2-4H 6H 4H Tolerance zone for effective diameter 6H Tolerance zone for For threads without specication of the Serevrin group always Seren group .N applies. elite) DIN 13 Limit thread plug gauge DIN 2280 GO the limt plug gauge DIN 2283, Part 1 and Pas NNO GO thread plug gauge DIN 2288, Part t and Part 2 GO tread ring gauge DIN 2786, Part 1 NO GO thread ring gauge Umit thread caper gauge Limit threed seting gauge Thread wear checking plug gauge DIN 2299, Pat 1 Gauges for fthand thread and sizes ot include in the folowing avenvews ‘oF gauges with tolerance zones not Standsrdized according to DIN 13 are ‘also manufactured on requestIn case of no indication of tolerance of limit throad plug gauges according class in the otder the intensively famed to ANSI B1.2 for Unified inch screw tolerance class of the table becomes threads are supplied with minus supplied. For thread ring gauges of tolerance. Ifa “plus” tolerance is round threads DIN 405 the tolerance required it has to be stated on the class has to be indicated. NO GO order, thread plug gauges or NO GO parts Metric ISO-thread DIN 13 Tolerance zones screw-in N° (nora) Gauge dimensions DIN ISO 1502 he) eek 4h 8H blank o* thin phosphate coating for threads 1-1.4 mm for threads 1-1.4 mm 6h 6H blank, phosphorized medium (m) or for thin galvanic for threads more than 1-14 mm for threads more than 1-1.4 mm protection layer 69 6H coarse (9) 89 7H British Standard Withworth threads British Standard fine threads BS 84 Gauge dimensions BS 919 Edternal thread close class medium class? free class* intemal thread medium class normal class normal class * GO thread ring gauges, NO GO thread ring gauges and limit thread caliper gauges as well as limit thread setting gauges for ‘extemal threads up to 3/4” nominal size are supplied in the tolerance classes .medium” and .ffee" and in the outfit .unplated”. tf the outfit .afterlating” is required this has to be indicated separately when ordering. Cylindrical pipe threads DIN ISO 228 Part 1 Gauge dimensions DIN ISO 228 Part 2 Tolerance class intemal thread / bolt ‘medium (m) A coarse (g) B Tolerance class internal thread / nut ‘medium (m) 1SO-metric trapeziodal threads DIN 103 Tolerance zones screw-in group .N Gauge dimensions DIN 103 Part 9 ‘medium (mn) Te 7H coarse (9) Be 9H Round thread DIN 405-1, 405-2 Tolerance zones screw-in group .N" (normal) Gauge dimensions DIN 405-3 Thand 70 7H Unified inch screw threads ANSI B1.1 Gauge dimensions thread plug gauges ANSI B 1.2 UNC-UNF-4 UN-6 UN-12 UN-16 UN-20 UN-28 UN-32 UN-UNS (special thread) ‘Thread ring gauges BS 919 xemal thread (bolt) 1A 2A 3A Intemal thread (nut 18 28 3B TKN 7 > Thread GaugesBy cos cauge Thr 1 gauc ior metric three coarse Lee) Nominal thread @ M 5 x075 M1 0.25) M14 (x25) M 12 025) M414 M16 M 18 M 2 M22 M 26 M 3 M 35 M4 M45 M M M M M M ZESeeseeecce NO GO thread ring gauge Limit thread plug gauge GO thread plug gauge NO GO thread plug gauge GO oF NO GO thread ring gauge Limit thread seting gauge Limit tread caliper gauge M 12-69 it plug gauge for minor diameter ir Limit thread plug gauge from 11mm - 40 mn nominal diameter GO thread plug gauge above 40 mm - 200 mm nerrinal NO GO thread plug gauge above 40 mm - 200 mm nominal diameter GO thread ring gaugeJoqowerp Jou 20} o6ne6 Bryd yw 26ine6 Jaden pent uur) 26neb Bums peasy yw 26ne6 Buu peaisa 0 ON 10 09 o6ne6 Enid peaup OD ON ‘6ne6 Bid peasy yur) o = Limit thread caliper gauge M.26x1-69 Enst Bne6 8rd peartp OD Limit thread setting gauge e]OWeP s0UN 40} 28ne6 Bryd YI ‘26ne6 saci peeiyt HUT 26ne6 Bumjas pean yu ‘6ne6 Buu pean 0 ON 40 09 pitch 0.5 mm Nomina thread O AON Thread gauges for the pitch sizes 0.2 and 0.28 mm on request. Wear inspection plug gauge for GO ring gauge M 20x0,5-69 P-Ap-Gut x035 x036 x035 x035 x035 x035 036 x038 x036 x035 2 22 25 3 35 a 45 5 55 6 65 BEEES55=5=555Jerewep so. 0} 96ne8 Gri! yA ‘26ne6 sedyeo peowyy yur] 2006 Bums pee ORR MOK KKK RK KRM MN MH MXR e606 Buu pang 09 ONO x x x x x x x KX KKK RK RXRKRERERRXEX E s6ne6 Gnd peangQDON << x x x x KKK KKK KKK KKK KK KKK KK KK KK = ebineG Bry peeinp OD x x x x x x x KKK KKK KKK KKK KKK KKK KKK RK KE OKO KK REL TTL 2026 Bd peasy HOO Nominal thread @ SSSSSSSSSSSSSSSSSSSSSESSSSSSESSSSSSSSSSSSSSSSSSSSSS nd Oe {2}9URD JoUUL 30} B66 Boyd UF] x = x {eIOWMP Lou JO} BEB Boyd wx x x x x x x KR KKK KKK oweD 1: x KKK KKK obne6 sedije> pean mur] = x x of ne6 socyeo peang mun x x x x x x x Kx Kx x n XO KKK Ke eGne6 Bumes peamn wy x x x eGne6 Gumes peoun mur) x x x x x x x x x x Kx x ‘atne6 Cui peasgos ONOD = = ee @Gne6 Buu peexa 0D 0N1009 = = = (09.0N x x x . “obi eon 09, x x ROK KK 26ne6 Brid pean ODON x * x 186 Bryd pean OD ON =< x x x x x x x x eGne6 Brid peony gg x x x xxx XXX XXX KKK KKK KKH e6ne6 Bryd pee og = x x 2ne6 Grid peop wu) — = = x ‘96ne6 Brid peana wn i i Bosco ooo SS SS SSS oosscsccees S eee 2 2 RK RR KR KR RR RRR eae 1° e s wer moCENPZESrSeRZaNageegares ne oot 5 3 5 i gos E zs = sss 285k e eee eee sess eee eee E Rl 10 seBnep peayysabnep peal S&S {B}OWIEP 20UNU 10} 26NEB Bod WX ‘26ne6 BUMS POEM UI] x ‘6ne6 Buu PeeAN OD ON 1009 x x XXX KKK KKK KKK KKK OE ‘206 Bred BEER ODON Xx XH 2 KO OO RR (M0 Bod PECAN OD. x x xX x XH KKK KK KKH KOK MOK KKM rN E a ee RRR RK NNN RWW WHR KKK KRM M HR KKK HR HMM REM E © 2 5 GB PERNRRSSSSSISSSSSSSISBR KER SSSRSSSSRLARS LES SARKK RARER G 8 sssssscssssssssssssssssssssssssssssssssssssssssssssssss {JoFOUUIP JOU 40} @BMEB BOYS YW dy u 2 HAN ~ rical fits, taper- and gear toothing gauges, “ja measuring gauges Gauges for cylijing gauges, =4 measuring gauges I fits, taper- and gear toothii Gauges for cyli eae limit plug range 3 mm - 80 mm made from wear-resistant ‘gauge steel, hardened, aged ‘measuring surfaces super finished NO GO part with 2 measuring surfaces Executions: €0 and NO GO por hardened gauge stel 60 and NO GO part 3 rard enrmed ‘On orders please indicate: Nominal size and fit or tolerance of workpiece eg. SW 10 H 10 or sw 10°" Next to those standard sizes ‘we also manufacture special sizes after customer drawings, Hexagon ring gauges on request. 30 Construction dimensions (works s' ee ed fo 1 32 25 628 65 4 abwe 32 to 4 25 ca 8 6 ‘abe 4 to 88 4 73 8 5 above 65 to 9 4 765 10 65 above 9 to 105 85 88 10 8 ‘above 105 to 12 7 7 10 8 ‘above 12 to 14 7 99 12 8 above 1410 17 9 110 12 8 above 17 10 21 12 124 12 8 ‘above 2110 32 12 130) 16 0 represented SW < d. u 2 L t GO part NO GO part s represented SW > dy —u | e Leae yauges for the nominal size range 0.5 mm - 5 mm ‘Measuring surfaces hardened, ground and lapped Executions: GO and NO GO part hardened gauge steel LE CO and NO GO part KYB hate chromed Limit ave for the nominal size range 0.5 mm - 5 mm ‘Measuring surfaces hardened, ‘ground and lapped Executions GO and NO GO part hardened gauge steel No, 1230 No. 1210 Limit for the nominal size range 3 mm - 100 mm. ‘Measuring surfaces hardened, ground and lapped blank forged Executions: GO ard NO GO part hardened gauge stee! GO and NO GO part hard chromed GO and NO GO pant tungsten carbide ing gauges, “.q measuring gauges Gauges for cylindrical fits, taper and gear toothirical fits, taper- and gear toothing gauges, sy measuring gauges Gauges for cyli Limit snap gauges single sided for the nominal size range 2 mm - 214 mm Forged execution ace. DIN 2231 ‘gauge steel, measuring surfaces hardened, ground and lapped Executi ies Pato} No. ea) Pr SE wngsten carbide rx} hardened gauge steel No. 1260 32 for the nominal size range 2 mm - 520 mm ta EPRI: Measuring surfaces hardened, 3- 10 | 3 | ‘ground and lapped | above 10- 50 | 4 | above 50- 90 6 Construction sizes: above 90- 160 a from 2 - 100 mm ace. DIN 2235 0 above 100 mm ace. works standard Executions: PEGE Novvinal size 2 - 50 rm Pe LE Nominal BPee size 50-520 mm No. 1200 No. 1200for the nominal size range 2 mm - 50 mm Measuring surfaces hardened, ‘ground and lapped No. 1208 Limit s econ nominal diameter 1.2 - 100 mm Measuring surfaces offset for grooves Measuring surfaces hardened, ground and lapped Dimensions acc. DIN 2235 Executions: For GO and NO GO pection of groove diameters On orders please indicate: Nominal size and tolerance for the groove diameter and for the wadth of the groove. eg. 20h8 x2 Se 33 Gauges for cylindrical fits, taper- and gear toothing gauges, “4 measuring gaugesGauges for cylindrical fits, taper- and gear toothing gauges, s44 measuring gauges ove diameters width Recon for the nominal range 1.2 - 100 mm Measuring surfaces hardened, ground and lapped Executions: For GO and NO GO inspection of ‘groove dismeters and ‘groove widths On order please indicate Nominal size and tolerance for the ‘groove diameter and for the with of the groove: eg, 20N8 x 240.1 No. 1120 ting gauges Nominal diameter from 1 - 500 mm for inspection of shaft diameters especially for easily formable parts, in gauge steel, hardened, ground and lapped Form C GO ring gauges DIN 2250, Form G Executi GO ring gauges DIN 2250 in the execution with dimensions to DIN 2250, No. NO GO ring gauges REGEN 2254 No. 1140Setting ring gauges STU ae] ring gauges alm Nominal diameter Nominal diameter from 1 - 100 mm from 1 - 500 mm Dimensions to DIN 2250, Form C Executions: Executions: Gauge stee! Setting rings for Satting rings above 100 mm @ x hardened ground 4 ‘application to DIN 2250 can be supplied in wooden box. and lapped Form C in gauge steel hardened, ground and lapped The nominal size of the bore of the setting ring for reamers lies at 22/3 of the tolerance zone for the bore of the workpiece calculated to DIN 22% fom the minimum size on (GO pan} Form 8 in gauge stee! Seiting rings for pneumatic length me: uring instruments hardened, ground and lapped The marking is carried out with the Delivery of sets in a storage container ‘actual size down to 3 decimal points. is possible. at No. 35Gauges for cylindrical fits, taper- and gear toothing gauges, ",4 measuring gauges In the machine building key joints {keys and splines) are frequently used to ensure a positive connection when transmitting higher forces. The connecting parts have to be fitted for that reason in a key slot without backash. ‘With these gauges itis possible to cheek: ‘© width of the stat on GO and NO GO © concentric postion of the slot and ‘© depth of the slot in shatts and hubs Each keyseat gauge is provided for a bigger range of diameters. The sliders for the slot widths as appearing in each diameter range can be exchanged easily ‘As normal outit sliders for standardized slot widths according to DIN 685 (6886 and 6887 are supplied (compare table). Sliders for other slot widths and tolerances are manufactured in special production after specification of the required sizes 36 Discreet eke Se eee Coir ee oe) gauge body for shatt-O-rang 1410.30 over 10 30 foimseT@ ERIE HERE GEES 1410 75 over 30-78 10 12 141618 1410..150 over 76 - 150 2 2% 32 6 1410..230__ over_160 - 230 a) 1410..330__over_230 - 330 566370. Inspection of keyseats with the keyseat gauge 1. Setting of the keyseat gauge The gauge is set onto the full fraction Of the shaft. The slider is moved down to the shaft and clamped. In that position the zero graduation of the depth measuring scale is brought in coincidence with the zero mark of the verier Afterwards the measuring scale is damped and the screw of the slider is loosened, 2. Inspection with the keyseat gauge The gauge is set onto the shaft and the slider is moved until reaching the ground of the slot. The depth of the slot can be read from the mm groduation of the depth scale, By that also the width of the slot he been checked for GO and for the concentriity’. The NO GO inspection Of the slot width is carried out by the with .A” signed side of the sliderge body for shaft-O-range 1420.17, 10-17 1420.30 over_17- 30 ee soe kc ea eed tolerance zones P9, JS9, PB or D10 1420.60 _over_30- 60 1420.75 over 60-78 1420..110 over 75 - 10 1420..150__over_110 - 160 1420..230 _over_160 - 230 1420..290__ over 230 - 290 1420..323 over 290 - 330 Inspection of keyseats of hubs with the keyseat gauge 3 4 5 6 & 10 12 14 6 18 20. 22 25 28 32 36, 40 46 50 56 63 70 1. Setting of the hub - keyseat gauge The gauge is set onto the front end of the workpiece. During this the ends stop pins are touching to the left and to the right of the slot in the bore Aiterwards the slider is moved t0 the board of the bore, clamped and the zero mark of the depth scale is brought in coincidence with the zero mark of the vernier on the slider The measuring scale is clamped and the screw of the slider is loosened, 2. Inspection with the hub ~ keyseat gauge The gauge is set onto the front end of the workpiece (end stop pins opposite the slot) and the slider is moved to the ground of the sot. The depth of the slot can be read now on the depth scale. By that at the same time the width of the keyway is checked for GO and for .concentrcity” The inspection for NO GO of the width of the slot is carried out by the with .A” signed side of the slider rical fits, taper- and gear toothing gauges, saa measuring gauges Gauges for cylirical fits, taper- and gear toothing gauges, =,q measuring gauges Gauges for cyli (block gauges) in wear resistant gauge steel hardened, aged, measuring surfaces super finished Limit flat gauges serve for inspection of fat fits particularly of slots in shafts and hubs, Executions: rs GO and NO GO part 1400 hardened gauge steel 03 60 an NO GO pat hard chromed On order please indicate: Nominal size and fit or the tolerance of the workpiece, eg. 8P9 or ate eaedincc eed ot ek uta 2 13 1» 8 “tt o 10 010 mo <0 Boe 10 w 18 7 3 700 aoe 18 6 0 ommana woe We Be woe 60 w 8a) aoe Ww 88810 doe 8) we 10a) 10 doe 12) 6 18) 10 Chengesrsoved 13 J 2] =| 0. SH7 +12 outfit up to nominal size 6mm 38 ul 12 0 +18 1SH7 Fo outfit above 6 to 150mmre )oime ce) in gauge steel, hardened, ground, tapered surfaces lapped For ingpection of tapered shafts and bores on tools and machine tools, For Morse tapers: No. 0.1, 2.3.4, 5,6 Executions: Taper plug gauge without tang, DIN 229 Taper sleeve gauge without tang, short, DIN 229 Taper sleeve gouge wath tang, long, DIN 324 a EG EG A EG g Taper plug gauge BERL win tang, DIN 230 Taper sleeve gauge with single-sided tang sleeve, but separately too. in gauge steel, hardened, ground tapered surfaces lapped for metic tapers No, 4, 6, 80, 100, 120 No, 80, 100, 120 Taper plug gauge wathout tang, DIN 234 No. 1301 N ‘Taper sleeve gauge EKER without tang, DIN 234 Taper plug ga vith tang, DIN 235, ‘Taper sleeve gauge with tang, DIN 235, (DIN 234) (DIN 235) ee, DIN 230, A MK C2 AAA DIN 229 Mc No, 1300 DIN 280 No. 1311 Ba KAN CIN 220 39 ling gauges, “ay measuring gauges ‘ical fits, taper- and gear toothii Gauges for cyliDrill chuck taper gauc in gauge steel, hardened, ground, in gauge steel, hardened, ground tapered surfaces lapped tapered surfaces lapped For inspection of spindle heads DIN 2221 and DIN 2222 ‘according to DIN 2079 and tapered stats according DIN 2080 Drill chuck tapers: No. B6, B10, B12, B16, B18, B22 824 BP Step tapers: No. 30, 40, 45, 50, 86, 60, 65 ist Executions: Execution Taper pag spina BO raver soove gauge 3 Teper ring Taper plug gauge, DIN 2221 auge for s, DIN 2079 gauge, DIN 2222 No. 1341 BETA for tapered shatts, DIN 2080 No. 1340 DIN 2079°— 30 B16 DIN 2221 No. 1351 fv OIN 2229) No, 1380, Gauges for cylindrical fits, taper- and gear toothing gauges, sq Measurifor diameter range from 0.1 to 20 mm ‘gauges are carefully hardened, aged, ground and lapped From diameter 3 mm onwards the marking is on the front end. The delivry is carried out separately or in boxed sets in steps of 0.1. 0.05 and 0.01mm. Further compositions on request UG Oe Bi We ak fo er Git 3mm 30 mm 05 um above 3 8 mm 351m 205 um above 10 to _20_mm 50mm =item O16 1 099mm 20mm =i om 7 10 mm 70m =1 om Corre cic ee eer er BEE rical fits, taper- and gear toothing gauges, s,q measuring gauges Gauges for cylitGauges for cylindrical fits, taper- and gear toothing gauges, “44 measuring gauges in wear - resistant steel, superfinished and lapped Suitable for inspection of squares and for acceptance tests of machine tools. Cr aes oe 2000200 90 x 200 72000250 90 x 250 78 22 72000300 90x 300 1 25 "2000360 ‘90 x 350 T04 28 2000-400 30x 400 116 3 a 2 TAN‘The test bars serve for the inspection and for the acoeptance test of machine tools and are produced with Morse taper, metric taper or steep taper from high-grade gauge steel. The surface is hardened and superfinished. Test bars th morse Catone lec Execution: Without drawn thread but with external thread and forcing-off nut and with 4 index lines on the front tend and on the rear fraction of the cylinder each. The marks on the front end are numbered fram 1 to 4, Manufacturing tolerances: (Cylindrical form error <3 um Concenticity error <3 um. Straighiness error < 3 um. d-mm Pe Morse 1 12 75 Morse 2 24 150 Morse 2 200 Morse 4 40 Morse 6 40 2101.80 metric 80 ing gauges, sw measuring gauges Gauges for cylindrical fits, taper- and gear toothirical fits, taper- and gear toothing gauges, “aq measuring gauges Gauges for cyli Execution: With drawn thread but without extemal thread with 4 index lines on the front end and on the rear fraction of the eyiinder each. The marks on the front end are numbered from 1 10 4 2102.20 Sk 20 24 180 Ce 2102.30.200. ‘Sk 30 32 200 0280300 $20, w 00 Ee 2102-40 320 «0 00 21049 ska 710246 sK46 o 200 | a a | | 2i01s0s00 SK © 60 aciae]e in wearresistant steel, hardened and superfinished. Concentricity <2 wm Straightness < 2 um These test bars are required for Poss Paseo cconcentrcity tess between centres ‘on machine tools ecc. The length of 2103.30 30 x 250 the clamping journal is 15 mm. aoa) a0 2103 50-400. 50 x 400. 2103.40.50. 40 x 600 2103.50.600. 50 x 600 2103.60 60 x 600 44 TN iReievea DIN 54 Gauges hardened, ground and lapped Kerb 26 x 30 DIN 5481 HAA Thanks to the higher number of engaged teeth serrated profiles offer the advantage that hub or shaft can bp adjusted in smallr distances tooth by tooth around the circumferential, direction Executions: Limit plug gauge for serratn GO plug gauge for serration 1NO GO plug gauge for serration BEE 0 ring gauge Te] for serration DE N0 GO ring gauge 0E8 for serration rea 7x 8 | 6x 65 8x 10 | 65 x 70 . 10x 12 70 x 75 7 24x25. SN 503 Gut 12x 1 | 7 x 8 1B x 17 | 80 x 85 17x 2 | 8 x 9 ax 24 | 9 x 96 26 x 30 | 95 x 100 30 x 34 | 100 x 105 36 x 40 | 105 x 110 40x 44 | NO x 15 45 x 50 | 15 x 120 50 x 55 | 120 x 125 85 x 60 Special sizes on raquest WAN 46 rical fits, taper- and gear toothing gauges, “aq measuring gauges Gauges for cyliGauges for cylindrical fits, taper- and gear toothing gauges, “a4 measuring gauges Gauge oan shafts and hut Gauges hardened, superfinished and lapped For the transmission of high and inteerittendly acting torques profiled shafts and bores are parcticularely suited Thanks to the symmetrical design of the profiles a single-sided drive is ‘avoided as in case of fited keys and, in adaition to that. exact centring of profiled shafts and hubs is ensured. Exeou By CO plug gauges PALO or spine protile hubs Nominal se range 12-145 mm GO ring gauges PALWA for spline protie shafts Nominal size range 12-145 mm On orders please indicate: Number of splines, nominal sizes {or extemal and internal diameters, 28 well as spline wadth. Spline profiles For the spline profile two centring poss: bilities are preferably used: Minor diameter fit (Hub is seated with the minor ciameter on the minor diameter of the shaft profile) © Flank diameter fit (Shaft and hub profile engage Cony along the flanks) 23 H7 x 28 Hil x OF 10 WAN 3 Be RUC a CUT Solined shalt and splined hub profiles, parallel- flanked, torque calculation pi Dimensions, light - weight series 5 with 6, 8 and 10 spines OE eeel eee Dimensions, medium - weight series nan with 6, 8 and 10 splines Cae Dimensions, heavy ~ weight series with 10 and 16 splines ee i Dimensions, light - weight series DIN 5641 DIN 5464 with 4 splines IN 5471 Dimensions, medium - weight series . with 6 splines DIN 5472, Splined shaft and splined hub profiles Splinad shaft and splined hub profil on sane Tolerances TAN