C.H.M.M.

COLLEGE FOR ADVANCED STUDIES

Metca Land, Chavarcode, Palayamkunnu P.O
Thrivannathapuram

Seminar Report
On
NIGHT VISION TECHNOLOGY

Presented by
HISHARA.N.S

FOURTH SEMESTER
B.Sc. COMPUTER SCIENCE
ROLL NO: 2
2008-2011
 C.H.M.M. COLLEGE FOR ADVANCED STUDIES
Metca Land, Chavarcode, Palayamkunnu P.O
Thrivannathapuram

DEPARTMENT OF COMPUTER SCIENCE

CERTIFICATE

This is to certify that the report on NIGHT VISION TECHNOLOGY, is a bonafide

record of seminar presented by HISHARA.N.S (Reg.No. ……………) towards
partial fulfillment for the award of the degree in B.Sc. computer Science by the
University of Kerala.

Staff in Charge Head of the Department

Place : Chavarcode
Date :
 Introduction

Night vision technology, by definition, literally allows one to see

in the dark. Originally developed for military use, it has provided the United

States with a strategic military advantage, the value of which can be

measured in lives. Federal and state agencies now routinely utilize the

technology for site security, surveillance as well as search and rescue. Night

vision equipment has evolved from bulky optical instruments in lightweight

goggles through the advancement of image intensification technology.

The first thing you probably think of when you see the words

night vision is a spy or action movie you've seen, in which someone straps on a

pair of night-vision goggles to find someone else in a dark building on a

moonless night. And you may have wondered "Do those things really work? Can

you actually see in the dark?"

The answer is most definitely yes. With the proper night-vision

equipment, you can see a person standing over 200 yards (183 m) away on a

moonless, cloudy night! Night vision can work in two very different ways,

depending on the technology used.

 1 Night vision technology was developed by the US

defense department mainly for defense purposes, but with the development

of technology night vision devices are being used in day to day lives. In this

seminar of mine I wish to bring out the various principles of working of

these devices that have changed the outlook both on the warfront and in our

common lives. Night Vision can work in two different ways depending on the

technology used. 1.Image enhancement- This works by collecting the tiny

amounts of light including the lower portion of the infrared light spectrum,

those are present but may be imperceptible to our eyes, and amplifying it to

the point that we can easily observe the image. 2:Thermal imaging- This

technology operates by capturing the upper portion of the infrared light

spectrum, which is emitted as heat by objects instead of simply reflected as

light. Hotter objects, such as warm bodies, emit more of this light than

cooler objects like trees or buildings.

Image enhancement
This works by collecting the tiny amounts of light, including the lower

portion of the infrared light spectrum, that are present but may be

imperceptible to our eyes, and amplifying it to the point that we can easily

observe the image.

2
3Thermal imaging
This technology operates by capturing the upper portion of the

infrared light spectrum, which is emitted as heat by objects instead of simply

reflected as light. Hotter objects, such as warm bodies, emit more of this

light than cooler objects like trees or buildings.

In this article, you will learn about the two major night-vision

technologies. We'll also discuss the various types of night-vision equipment

and applications. But first, let's talk about infrared light.

The Basics

In order to understand night vision, it is important to understand

something about light. The amount of energy in a light wave is related to its

wavelength: Shorter wavelengths have higher energy. Of visible light, violet

has the most energy, and red has the least. Just next to the visible light

spectrum is the infrared spectrum.

Infrared light can be split into three categories:

1
2
3 Near-infrared (near-IR)

4 Closest to visible light, near-IR has wavelengths that range from 0.7 to 1.3

microns, or 700 billionths to 1,300 billionths of a meter.

5
6 Mid-infrared (mid-IR)

0Mid-IR has wavelengths ranging from 1.3 to 3 microns. Both near-IR and

mid-IR are used by a variety of electronic devices, including remote controls.

7
8 Thermal-infrared (thermal-IR)

0Occupying the largest part of the infrared spectrum, thermal-IR has

wavelengths ranging from 3 microns to over 30 microns.

The key difference between thermal-IR and the other two is that

thermal-IR is emitted by an object instead of reflected off it. Infrared light

is emitted by an object because of what is happening at the atomic level.

Atoms

Atoms are constantly in motion. They continuously vibrate, move and

rotate. Even the atoms that make up the chairs that we sit in are moving

around. Solids are actually in motion! Atoms can be in different states of

excitation. In other words, they can have different energies. If we apply a lot

of energy to an atom, it can leave what is called the ground-state energy

level and move to an excited level. The level of excitation depends on the

amount of energy applied to the atom via heat, light or electricity.

An atom consists of a nucleus (containing the protons and neutrons) and an

electron cloud. Think of the electrons in this cloud as circling the nucleus in

many different orbits. Although more modern views of the atom do not depict

discrete orbits for the electrons, it can be useful to think of these orbits as

the different energy levels of the atom. In other words, if we apply some

heat to an atom, we might expect that some of the electrons in the lower

energy orbitals would transition to higher energy orbitals, moving farther

from the nucleus.

Once an electron moves to a higher-energy orbit, it eventually wants

to return to the ground state. When it does, it releases its energy as a photon

-- a particle of light. You see atoms releasing energy as photons all the time.

For example, when the heating element in a toaster turns bright red, the red

color is caused by atoms excited by heat, releasing red photons. An excited

electron has more energy than a relaxed electron, and just as the electron

absorbed some amount of energy to reach this excited level, it can release

this energy to return to the ground state. This emitted energy is in the form
of photons (light energy). The photon emitted has a very specific wavelength

(color) that depends on the state of the electron's energy when the photon is

released.

Anything that is alive uses energy, and so do many inanimate items

such as engines and rockets. Energy consumption generates heat. In turn, heat

causes the atoms in an object to fire off photons in the thermal-infrared

spectrum. The hotter the object, the shorter the wavelength of the infrared

photon it releases. An object that is very hot will even begin to emit photons

in the visible spectrum, glowing red and then moving up through orange, yellow,

blue and eventually white. Be sure to read How Light Bulbs Work, How Lasers

Work and How Light Works for more detailed information on light and photon

emission.

Thermal Imaging and Image Enhancement

Here's how thermal imaging works:

• A special lens focuses the infrared light emitted by all of the objects in

view.

• The focused light is scanned by a phased array of infrared-detector

elements. The detector elements create a very detailed temperature pattern

called a thermogram. This information is obtained from several thousand

points in the field of view of the detector array.

• The thermogram created by the detector elements is translated into

electric impulses.
• The impulses are sent to a signal-processing unit, a circuit board with a

dedicated chip that translates the information from the elements into data

for the display.

• The signal-processing unit sends the information to the display, where it

appears as various colors depending on the intensity of the infrared emission.

The combination of all the impulses from all of the elements creates the

image.

The basic components of a thermal-imaging system

Types of Thermal Imaging Devices

Most thermal-imaging devices scan at a rate of 30 times per second. They can

sense temperatures ranging from -4 degrees Fahrenheit (-20 degrees Celsius)

to 3,600 F (2,000 C), and can normally detect changes in temperature of

about 0.4 F (0.2 C).

It is quite easy to see everything during the day. ..but at night, you can see very little.

Thermal imaging lets you see again.

There are two common types of thermal-imaging devices:
1
• Un-cooled - This is the most common type of thermal-imaging device.
The infrared-detector elements are contained in a unit that operates

at room temperature. This type of system is completely quiet,

activates immediately and has the battery built right in.

• Cryogenically cooled - More expensive and more susceptible to damage

from rugged use, these systems have the elements sealed inside a

container that cools them to below 32 F (zero C). The advantage of

such a system is the incredible resolution and sensitivity that result

from cooling the elements. Cryogenically-cooled systems can "see" a

difference as small as 0.2 F (0.1 C) from more than 1,000 ft (300 m)

away, which is enough to tell if a person is holding a gun at that

distance!

While thermal imaging is great for detecting people or working in

near-absolute darkness, most night-vision equipment uses image-

enhancement technology.

Image Enhancement
Image-enhancement technology is what most people think of when you

talk about night vision. In fact, image-enhancement systems are normally

called night-vision devices (NVDs). NVDs rely on a special tube, called an

image-intensifier tube, to collect and amplify infrared and visible light.

 The image-intensifier tube changes photons to electrons and back again.

Here's how image enhancement works:

1 A conventional lens, called the objective lens, captures ambient light

and some near-infrared light.

2 The gathered light is sent to the image-intensifier tube. In most

NVDs, the power supply for the image-intensifier tube receives power from

two N-Cell or two "AA" batteries. The tube outputs a high voltage, about

5,000 volts, to the image-tube components. The image-intensifier tube has a

photocathode, which is used to convert the photons of light energy into

electrons.

3 As the electrons pass through the tube, similar electrons are released

from atoms in the tube, multiplying the original number of electrons by a

factor of thousands through the use of a microchannel plate (MCP) in the

tube. An MCP is a tiny glass disc that has millions of microscopic holes

(microchannels) in it, made using fiber-optic technology. The MCP is

contained in a vacuum and has metal electrodes on either side of the disc.
Each channel is about 45 times longer than it is wide, and it works as an

electron multiplier.

When the electrons from the photo cathode hit the first electrode of

the MCP, they are accelerated into the glass microchannels by the 5,000-V

bursts being sent between the electrode pair. As electrons pass through the

microchannels, they cause thousands of other electrons to be released in

each channel using a process called cascaded secondary emission. Basically,

the original electrons collide with the side of the channel, exciting atoms

and causing other electrons to be released. These new electrons also collide

with other atoms, creating a chain reaction that results in thousands of

electrons leaving the channel where only a few entered. An interesting fact

is that the microchannels in the MCP are created at a slight angle (about a

5-degree to 8-degree bias) to encourage electron collisions and reduce both

ion and direct-light feedback from the phosphors on the output side.

1 At the end of the image-intensifier tube, the electrons hit a screen

coated with phosphors. These electrons maintain their position in relation to

the channel they passed through, which provides a perfect image since the

electrons stay in the same alignment as the original photons. The energy of

the electrons causes the phosphors to reach an excited state and release

photons.

Night-vision images are known for their eerie green tint

These phosphors create the green image on the screen that has come to

characterize night vision

1 The green phosphor image is viewed through another lens, called the

ocular lens, which allows you to magnify and focus the image. The NVD may

be connected to an electronic display, such as a monitor, or the image may be

viewed directly through the ocular lens.

Generations
Generation 0
The earliest (1950's) night vision products were based on image

conversion, rather than intensification. They required a source of invisible

infrared (IR) light mounted on or near the device to illuminate the target

area.
Generation 1
The "starlight scopes" of the 1960's (Vietnam Era) have three image

intensifier tubes connected in a series. These systems are larger and

heavier than Gen 2 and Gen 3. The Gen 1 image is clear at the center but

may be distorted around the edges. (Low-cost Gen 1 imports are often

mislabeled as a higher generation.

Figure 1 illustrates first-generation night vision. [Not a great topic sentence

but it does has the advantage of calling attention to the figure.] Incoming

light is collimated by fiber optic plates before impacting a photocathode t

which releases electrons, which in turn impact a phosphor screen. The

excited screen emits green light into a second fiber optic plate, and the

process is repeated. The complete process is repeated three times providing

an overall gain of 10,000.

Generation 2
The micro channel plate (MCP) electron multiplier prompted Gen 2

development in the 1970s. The "gain" provided by the MCP eliminated the

need for back-to-back tubes - thereby improving size and image quality. The

MCP enabled development of hand held and helmet mounted goggles.

Second-generation image intensification significantly increased gain

and resolution by employing a microchannel plate. Figure 2 depicts the basic

configuration. [These two sentences could have been combined: "Figure2

depicts how second-generation image ... plate."] The microchannel plate is

composed of several million microscopic hollow glass channels fused into a

disk. Each channel, approximately 0.0125 mm in diameter, is coated with a

special semiconductor which easily liberates electrons. A single electron

entering a channel initiates an avalanche process of secondary emission,

under influence of an applied voltage, freeing hundreds of electrons. These

electrons, effectively collimated by the channel, increase the resolution of

the device. With additional electron optics, details as fine as 0.025 mm can

be realized (half the diameter of a human hair).

 Current image intensifiers incorporate their predecessor's resolution

with additional light amplification. The multialkali photocathode is replaced

with a gallium arsenide photocathode; this extends the wavelength

sensitivity of the detector into the near infrared. The moon and stars

provide light in these wavelengths, which boosts the effectively available

light by approximately 30%, bringing the total gain of the system to around

30,000.

[No topic sentence. Indeed one might have moved this material to the front

in a more dramatic way, perhaps by calling attention to the movie `Silence of

the Lambs.'] slight green tint similar to some sunglasses. The apparent

lighting of the landscape on a dark night is comparable to what the unaided

eye would see on a clear winter night with fresh snow on the ground and a

full moon.
Generation 3
Two major advancements characterized development of Gen 3 in the

late 1970s and early 1980s: the gallium arsenide (GaAs) photocathode and

the ion-barrier film on the MCP. The GaAs photocathode enabled detection
of objects at greater distances under much darker conditions. The ion-

barrier film increased the operational life of the tube from 2000 hours (Gen

2) to 10,000 (Gen 3), as demonstrated by actual testing and not

extrapolation.

Generation 4

For a good explanation of this commonly misunderstood advancement in

night vision technology.

When discussing night vision technology, you also may hear the term

"Omnibus" or "OMNI". The U.S. Army procures night vision devices through

multi-year/multi-product contracts referred to as "Omnibus" - abbreviated

as "OMNI". For each successive OMNI contract, ITT has provided Gen 3

devices with increasingly higher performance. ( See range detection chart

directly below) Therefore, Gen 3 devices may be further defined as OMNI

3, 4, 5, etc. Current Omnibus contract as of 2006 is OMNI 7.

If you're using night vision to find a lost person in the woods, to locate

boats or buoys on the water, or to stargaze into the wilderness, you need

Generation 3 because it creates the best images when there is very little

ambient light. Generation 2 may be the choice in situations with higher levels

of ambient light.
KEY GENERATION DEVELOPMENTS:

GENERATION 1 (Developed in 1960's)

• Vacuum Tube Technology
• Full Moon Operation
• Amplification: 1,000
• Operating Life: 2,000 Hours

GENERATION 2 (Developed in 1970's)

• First Micro channel Plate (MCP) Application
• One-Quarter Moon Operation
• Amplification: 20,000
• Operating Life: 2,500 Hours

GENERATION 2+ (1970s)
• Development increased image tube bias voltage to improve gain.
• Additionally, a glass faceplate was added to improve resolution.

GENERATION 3 (Developed in 1990's)

• Improved MCP & Photocathode
• Starlight Operation
• Amplification: 40,000
• Operating Life: 10,000 Hour

GENERATION 3 Enhanced (2000's)

• Improvements in the photocathode and MCP resulted in increased gain and
resolution.
Characteristics of Night Vision

Using intensified night vision is different from using regular binoculars

and/or your own eyes. Below are some of the aspects of night vision that you

should be aware of when you are using an image intensified night vision

system.

Textures, Light and Dark

Objects that appear light during the day but have a dull surface may

appear darker, through the night vision unit, than objects that are dark

during the day but have a highly reflective surface. For example, a shinny

dark colored jacket may appear brighter than a light colored jacket with a

dull surface.

Depth Perception

Night vision does not present normal depth perception.

Fog and Rain

Night vision is very responsive to reflective ambient light; therefore,

the light reflecting off of fog or heavy rain causes much more light to go

toward the night vision unit and may degrade its performance.

Honeycomb
This is a faint hexagonal pattern which is the result of the manufacturing
process.
Black Spots

A few black spots throughout the image area are also inherent

characteristics of all night vision technology. These spots will remain

constant and should not increase in size or number. See example below of an

image with black spots.

* Do not be concerned if you see this feature-it is an inherent

characteristic found in light amplification night vision systems that

incorporate a microchannel plate in the intensifier

Equipment and Applications

Night-vision equipment can be split into three broad categories:

 Scopes

Normally handheld or mounted on a weapon, scopes are monocular (one

eye-piece). Since scopes are handheld, not worn like goggles, they are good

for when you want to get a better look at a specific object and then return

to normal viewing conditions.

 Goggles

While goggles can be handheld, they are most often worn on the head.

Goggles are binocular (two eye-pieces) and may have a single lens or stereo

lens, depending on the model. Goggles are excellent for constant viewing,

such as moving around in a dark building.

 Cameras

Cameras with night-vision technology can send the image to a monitor

for display or to a VCR for recording. When night-vision capability is desired

in a permanent location, such as on a building or as part of the equipment in a

helicopter, cameras are used. Many of the newer camcorders have night

vision built right in.

Applications
Common applications for night vision include:
• Military
• Law enforcement
• Hunting
• Wildlife observation
• Surveillance
• Security
• Navigation
• Hidden-object detection
• Entertainment

The original purpose of night vision was to locate enemy targets at

night. It is still used extensively by the military for that purpose, as well as

for navigation, surveillance and targeting. Police and security often use both

thermal- imaging and image-enhancement technology, particularly for

surveillance. Hunters and nature enthusiasts use NVDs to maneuver through

the woods at night.

Detectives and private investigators use night vision to watch people

they are assigned to track. Many businesses have permanently-mounted

cameras equipped with night vision to monitor the surroundings.

A really amazing ability of thermal imaging is that it reveals whether an area

has been disturbed -- it can show that the ground has been dug up to bury
something, even if there is no obvious sign to the naked eye. Law

enforcement has used this to discover items that have been hidden by

criminals, including money, drugs and bodies. Also, recent changes to areas

such as walls can be seen using thermal imaging, which has provided

important clues in several cases.

Many people are beginning to discover the unique world that can be

found after darkness falls. If you're out camping or hunting a lot, chances

are that night-vision devices can be useful to you -- just be sure to get the

right type for your needs.

Early Attempts at Night Vision Technology

 Military tacticians throughout history have seen the advantages of

being able to maneuver effectively under the cover of darkness. Historically,

maneuvering large armies at night carried such risks that it was rarely

attempted. During WW II, the United States, Britain, and Germany worked

to develop rudimentary night vision technology. For example, a useful

infrared sniper scope that used near-infrared cathodes coupled to visible

phosphors to provide a near-infrared image converter was fielded. A small

number, perhaps 300 Sniperscopes, were shipped to the Pacific sometime in

1945, but received very little use. Their range was less than 100 yards, and

they were used mainly for perimeter defense. However this device had

several disadvantages. The infrared sniper scope required an active IR

searchlight that was so large it had to be mounted on a flatbed truck. This

active IR searchlight could be detected by any enemy soldier equipped with

similar equipment. The rifle-mounted scope also required cumbersome

batteries and provided limited range. However, the infrared sniper scope

showed that night vision technology was on the

horizon. Military leaders immediately saw many uses for this technology

beyond sniping at the enemy under cover of darkness. An army equipped with

night vision goggles, helmets, and weapons sights would be able to operate

24 hours a day. The Army Corps of Engineers, for example, would be able to

build bridges and repair roads at night providing a measure of safety from

airborne attack. The next challenge in night vision technology would be the

development of passive systems that did not require IR searchlights that

might give away a soldier's position to the enemy.

 The Prescription
1. Manoeuvre

In order for infantry sub-units to move and fight at night, every

soldier requires some type of NVD. These devices allow the soldier to

engage targets at the maximum range of his personal weapon and manoeuvre

across the battlefield with good situational awareness.

The infantry needs to replace all of their current Gen-2 and older

Gen-3 NVD’s with the far superior Gen-3 Omni-5 models. The authors

suggest that the minimum number required by dismounted infantry sections

is one set of NVG’s per fire team. With these, the sect will be able to move

at night as it does in the day. However, as noted earlier, in order to take full

advantage of the technology, leaders and soldiers must wear them at all

times. While the initial training will be difficult and resisted by some

soldiers, the benefits will soon become clear to leaders.

NVG’s should have the ability to be mounted to the helmet and flip up in the

same manner as an aviator’s or the US Army's PVS-7Ds. The LAV crew comd

requires NVG’s in addition to the gunner’s thermal sight to enable him to

operate with his head outside of the turret. This would increase his

peripheral vision capabilities and assist him in maintaining situational

awareness; both of these would be lost if he remained inside the turret and

focused on the thermal sight.

A possible alternative to the AN/PVS-7D is the AN/PVS-14. This

monocular’s flexibility is unsurpassed in that it can be used as a hand-held,

helmet-mounted or weapon-mounted NVD. It is currently being issued to US

Ranger battalions. Its great advantage is that in helmet-mounted mode it

leaves one eye unrestricted to allow for increased situational awareness.

An added piece of available equipment to be considered for limited

purchase is the afocal magnifier lens that can be attached to PVS-7D Gen-3

Omni-5 NVGs or PVS-14. It would be useful for soldiers who require long-

range observation capabilities (such as pl comds) who do not necessarily

require a weapon sight. It is especially worthy of consideration because of

its relative low procurement cost.

With a PVS-7D (NVG) and one of these afocal lenses, the user gains dual

NVD capability; he can move at night using the NVGs and then attach the

afocal lens (to be used like conventional hand-held binoculars) upon reaching

a fixed position. US sniper teams have found this combination indispensable.

Such a pairing would also be useful for OP’s

2. Firepower

Seeing is not enough; soldiers must also be able to hit and kill a target.

Canadian infantry units do not have the ability to effectively engage targets

at night without illumination. The only way to gain this capability is by using
NVG’s coupled with an IR pointing device (such as the PAQ-4C) or by using a

weapon night sight such as the British-made Kite sight.

The PAQ-4C (called "Pack – 4" by US forces) is the latest and improved

version of the PAQ-4B, and currently in use by Canadians deployed with

KFOR/SFOR. The AN/PAQ-4C is an infared weapon aiming light that allows

the soldier to aim his weapon while still using NVG’s. The IR light that is

projected from this device is invisible to the naked eye; however, the light

can easily be seen when using image intensification devices. The light

provides a rapid, accurate aiming point from which to engage targets at

night.

With their longer ranges, the C-9 LMG and C-6 GPMG require a night

sight with a corresponding range capability. One option is to employ a night

sight such as the Gen-3 Kite or Maxikite sight (which is also being employed

by Canadian Forces in KFOR/SFOR). This will allow the C-9 and C-6 gunners

to engage targets out to 600m. With the Kite sight the sect would also gain

greater depth in their ability to observe of the battlefield going beyond the

range of their NVGs.

FIBUA and certain other operations require special considerations and

equipment. For a number of years special and police forces have employed

weapon-mounted white light devices in FIBUA-type operations. In addition

to allowing rapid target acquisition, white light has the advantage of blinding

image intensification equipment. It can also temporarily dazzle and disorient

an enemy with unprotected eyesight – even in daylight or lighted rooms.

SureFire lights In addition to optical NVD’s there are pyrotechnic IR

illumination devices. These include Para flares, illumination rounds, pen

flares, and trip flares. To the naked eye, these have the same brightness as

a burning match; however, through NVD’s, they "light up the sky." The US

Army employs them and we should too.

All of these equipment choices beg the question "what is the right

mix?" The answer is not universal and depends on the operation at hand.

However, it is suggested that the scale of issue for the C-9 and C-6 should

be Gen-3 Kite/Maxikite sights. Riflemen should be equipped with NVGs and

PAQ-4C’s. When it is desirable to mount the Kite sights on the C-7s for

pinpoint accuracy, the C-9 gunners would utilize the NVG and PAQ-4C

combination (this is not necessarily a compromise for the latter since it

would reduce washout from muzzle flash). Thus, comds would allot night

vision equipment based on the tasks for his sub-unit. It is clear that other

forces similar in size and composition to our, reflect this same concern for

adequate NVD’s.

3. Command and Control

Commanding dismounted infantry during normal daylight operations is

an intricate task; to attempt the same during reduced visibility operations is

infinitely more challenging. Even after NVD’s are obtained, there must be a

means for leaders to guarantee control and thus reduce the risk of

fratricide.

The most important infantry night command aid is the Ground

Commander's Pointer (GCP). This device is an IR laser with a range of 8 km+.

It allows comds to direct soldiers equipped with NVD’s by indicating both

targets and boundaries. For example, a pl comd could indicate trenches to

his sect comds and the OC, subsequently giving his arcs for the

consolidation. Recce Pl could then mark depth objectives for attack

helicopters.

The GCP-1 comes in two versions: the GCP-1/2A (50mW) and the

longer range GCP-1/2B (100mW). The GCP-1’s are hand held, and the GCP-2’s

can be mounted on a weapon. If the GCP-2A/B are employed, the PAQ-4C is

not required.

Soldiers and comds must have a means to establish positive combat

identification at night in order to prevent fratricide; "Warrior Glotape" is a

very inexpensive solution. To the naked eye, it appears as black duct tape in

both finish and texture. When illuminated by normal visible light it exhibits

no special reflective characteristics. However, when illuminated by an IR

source (for example, GCP’s, PAQ-4C’s, or LAV-3 IR spotlights) the tape

glows brightly. "Warrior Glotape" could be placed on the back of a soldier’s

helmet and on the forestock of his weapon. An obvious criticism of this

system is that NVD equipped enemy forces would also see our forces during

IR illumination. This is true; however, illumination by comds would take place

only seconds before engagement as a final confirmation of identity. Thus,

the safeguard against fratricide far outweighs the risk of detection.

The Phoenix IR beacon is a longer-range device that should be used in

addition to glow tape. The IR beacon - when activated - emits a strobe,

which can only be detected by NVD’s. The programmable nature of this

device means it lends itself to marking different friendly locations during

the conduct of patrols, link up operations, and other night operations. It can

be also be used to mark vehicles, routes, attack positions, rolling

replenishments, and landing zones.

The problem of control and identification remains during the use of

thermal sights, so an item to meet this requirement needs investigation. It

must be remembered that thermal sights prevent one from seeing visible

white light or IR light sources, such as chem lights. Thermal panel markers

are a useful and cost-effective solution. They will assist in the marking of a

variety of operationally significant locations (such as identifying obstacle

breach sites for LAV-3 drivers using thermal viewers) and help to prevent

fratricide. The Thermal Identification Panel (TIP - manufactured by NVEC)

is a thermal reflective marker designed for use with thermal sights and

viewers. TIPs work by showing the contrast between their cold spots and

the warmer background temperature.

 CONCLUSION

It will be useful to address this problem by examining the three

following combat functions: manoeuvre, fire power and command. All three

of these are affected by the shortfalls that exist in our NVD stores. It is

important to keep in mind, however, that more equipment alone is not the

solution to all of our problems. The correct attitude of individual soldiers

about the employment of NVD’s must also be guaranteed; it is unacceptable

to see night vision goggles (NVG’s) dangling around soldiers’ necks instead of

being mounted to a head harness or helmet. The optimistic news is that one

estimate shows an entire battalion could be outfitted with the ability to

"own the night" for less than two million dollars (roughly the price of one

LAV-3).
 References

1. www.answer.com

2. www. night vision.com

3. www.google.com

4.www.wikipedia.org
 ACKNOWLEDGEMENT

I extend my sincere gratitude towards Prof. SHIJIN.M Head of Department

for giving us his invaluable knowledge and wonderful technical guidance

I express my thanks to Mr. SAM RAJ our Computer Lab Instructor and also
to our staff advisor Ms. SAJIMOL for their kind co-operation and guidance for
preparing and presenting this seminar.

I also thank all the other faculty members of AEI department and my friends
for their help and support.

With gratitude
HISHARA.N.S