Scribd
Upload
401 views

Experiment 08-A2d

The document describes an experiment to convert analog signals to digital signals using an ADC0804 integrated circuit analog-to-digital converter. Key steps include assembling the converter circuit, applying various analog input voltages from 0 to 5.12V to the circuit using a potentiometer, and recording the corresponding 8-bit digital outputs displayed by LEDs. The objective is to verify that the sum of the digital output values equals the analog input voltage, confirming the converter is functioning properly with a resolution of 0.39%.

Uploaded by

api-277396867
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
401 views

Experiment 08-A2d

The document describes an experiment to convert analog signals to digital signals using an ADC0804 integrated circuit analog-to-digital converter. Key steps include assembling the converter circuit, applying various analog input voltages from 0 to 5.12V to the circuit using a potentiometer, and recording the corresponding 8-bit digital outputs displayed by LEDs. The objective is to verify that the sum of the digital output values equals the analog input voltage, confirming the converter is functioning properly with a resolution of 0.39%.

Uploaded by

api-277396867
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Experiment

8
Analog-to-Digital Converter
Objectives
To convert analog signals to digital signals using an IC D/A converter.

Required Materials
(1) Power supply 0 to 5.12 volts

(1) 10fd tantalum capacitor

(1) ADC0804 integrated circuit

(8) 330 resistors

(1) 10K Potentiometer

(1) 150pfd capacitor

(8) LEDs

(1) 10K resistor

Introduction
Eight-bit ADCs in IC form require only eight clock pulses using a register that performs a function
called successive approximation.
Figure 8-1 shows the schematic diagram of the ADC0804 analog-to-digital converter IC. It uses an
internal successive-approximation register (SAR).The circuit is capable of converting an analog voltage into a proportional 8-bit digital output. The voltage range to be converted is determined by
applying the maximum desired voltage to VDC at pin 20. The analog input is applied across VIN(+)
and
VIN(). Since there are 256 (28) different binary digital numbers produced at the eight output leads,
the percent the analog voltage changes is .39 percent (1/255 = .0039 = .39%) before one binary bit
changes.This is called resolution.
The IC contains an internal clock. Its pulses are fed into the IC when an external resistor and capacitor are connected to the CLK R and CLK IN inputs. The conversion begins every time a Low is
applied to WR.At the end of the conversion process, output INTR goes Low.Also, the eight outputs
that represent the analog input voltage will be present at the active-High output lines DB0 to DB7.
Connecting output line INTR to input WR will cause the IC to continually update itself by repeating the conversion process. The conversion process repeats so quickly that the LEDs strobe and
appear to be permanently on. The fast operation also enables the LEDs to immediately change the
digital display when the applied analog input voltage is varied.

Procedure Information
The output voltage range of the ADC in this experiment is 0 to 5.12 volts.A variable analog voltage
is applied to the input by a 10K potentiometer. LEDs at the output leads show the converted binary number.

35

36

Experiment 8

Analog-to-Digital Converter

10 k
1
150 pF
2

CS

VDC

RD

CLK R

WR

DB0

3
4

10 k

Analog
Input
Voltage

5
6
V

7
8
9
10

CLK IN

DB1

INTR

DB2

20
+
19

DB3

10 F Tantalum
LSB

18
330
17
330
16
330

ADC0804

VIN (+)

5.120 VDC

15
330
14

VIN ()

DB4

AGND

DB5

VREF/2

DB6

DGND

DB7 11

13

330
330

12
330
330

Figure 8-1

MSB

A/D Converter Circuit

Step 1
Assemble the circuit shown in Figure 8-1.

Step 2
Turn on the power supply.

Step 3
With one end of a jumper wire connected to ground, momentarily touch the other end to input
WR.

Step 4
Apply the analog voltage listed on the top line of the input section of Table 8-1.
Input
Measured
Analog
Voltage
0V
0.4V
1.0V
1.6V
2.3V
3.5V
4.6V
5.12V

DB7
2.56V

Table 8-1 A/D Converter Test Results


Output
Resolution Values
DB6
DB5
DB4
DB3
DB2
1.28V
0.64V
0.32V
0.16V
0.08V

DB1
0.04V

DB0
0.02V

Resolution
Total

Experiment 8

Analog-to-Digital Converter

Step 5
Fill in the output section to show the logic states of each digital output lead. Place a 1 in the column
if the corresponding LED turns on, and a 0 to indicate an LED that does not light.

Step 6
Add all of the resolution values of each column that has a 1. Place the sum in the column labeled Resolution Total. Does the number equal the applied analog input voltage?

Step 7
Repeat steps 5 and 6 for each of the remaining input analog voltages in Table 8-1.

PROCEDURE QUESTION 1
How should the sum of resolution values and the analog voltages compare with each other?

Experiment Questions
1. How many clock pulses are required by the ADC0804 IC to complete one analog-to-digital conversion?
2. The resolution of the ADC0804 IC is _______ percent.
3. At the end of each analog-to-digital conversion, the INTR lead goes _______ (Low, High).
4. An analog voltage of 1 volt applied to the circuit in Figure 8-1 will produce a digital output of
______.

PROCEDURE QUESTION ANSWER


They should be equal.

37

You might also like