Scribd
Upload
3K views

VOIP On Packet Tracer PDF

This document discusses configuring Voice over IP (VoIP) on Packet Tracer. It describes VoIP and its associated terms. The steps to make a VoIP call are outlined, including digitization, encoding, packetization and transmission of voice over IP networks. The document then provides instructions for setting up IP phones on Packet Tracer, including powering on the phones, assigning IP addresses via DHCP, configuring VoIP on the router and switch interfaces, and assigning phone numbers so calls can be placed between the IP phones.

Uploaded by

Head Bang
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
3K views

VOIP On Packet Tracer PDF

This document discusses configuring Voice over IP (VoIP) on Packet Tracer. It describes VoIP and its associated terms. The steps to make a VoIP call are outlined, including digitization, encoding, packetization and transmission of voice over IP networks. The document then provides instructions for setting up IP phones on Packet Tracer, including powering on the phones, assigning IP addresses via DHCP, configuring VoIP on the router and switch interfaces, and assigning phone numbers so calls can be placed between the IP phones.

Uploaded by

Head Bang
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

VOIP on Packet Tracer

Voice over IP (VoIP, or voice over Internet Protocol) commonly refers to the
communication protocols, technologies, methodologies, and transmission techniques
involved in the delivery of voice communications and multimedia sessions over Internet
Protocol (IP) networks, such as the Internet. Other terms commonly associated with VoIP
are IP telephony,Internet telephony, voice over broadband (VoBB), broadband telephony,
IP communications, and broadband phone.
Internet telephony refers to communications services voice, fax, SMS, and/or voicemessaging applications that are transported via the Internet, rather than the public
switched telephone network (PSTN). The steps involved in originating a VoIP telephone
call are signaling and media channel setup, digitization of the analog voice signal, encoding,
packetization, and transmission as Internet Protocol (IP) packets over a packet-switched
network. On the receiving side, similar steps (usually in the reverse order) such as
reception of the IP packets, decoding of the packets and digital-to-analog conversion
reproduce the original voice stream. Even though IP telephony and VoIP are used
interchangeably, IP telephony refers to all use of IP protocols for voice communication by
digital telephony systems, while VoIP is one technology used by IP telephony to transport
phone calls

Let us apply it on packet tracer.

This IP Phone is displayed below. And when we try to go to any other mode its give us error
and ask us to switch it on first.

For that, go to Physical mode and put the power adapter (in the bottom right corner) into
the phone as shown in figure.

Now, we have inserted the antenna into IP phone. Repeat it for other phones as well.

Now, we see that interface of IP phone is UP.

Now, go to router and assign IP address.

We will have to set DHCP server on router to assign IP addresses to IP phones.

We will have to give an additional command for voip.


Router(dhcp-config)#option 150 ip 192.168.1.1

Now, let us apply commands to the router for voip. You might have noticed we took 2811
series router because it facilitates the following commands.

Continued.

Now, we will go to the switch and make the interfaces support voip as follows.

After that, we will have to assign phone number to our IP phone by applying following
commands.

Continued

Now, we can see that in GUI mode of Phone, we have a phone number available.

This means that we can call from one phone to the other. Lets do that.

And when we pick up the reciever, it says that we are connected.

Commands on Router for VOIP


Router(config)#ip dhcp pool voice
Router(dhcp-config)#option 150 ip 192.168.1.1
Router(dhcp-config)#exit
Router(config)#telephony-service
Router(config-telephony)#max-dn 5
Router(config-telephony)#max-ephones 5
Router(config-telephony)#ip source-address 192.168.1.1 port 2000
Router(config-telephony)#auto assign 1 to 9
Router(config-telephony)#exit
Router(config)#ephone-dn 1
%LINK-3-UPDOWN: Interface ephone_dsp DN 1.1, changed state to up
Router(config-ephone-dn)#number 12345
Router(config-ephone-dn)#exit
%IPPHONE-6-REGISTER: ephone-1 IP:192.168.1.2 Socket:2 DeviceType:Phone has
registered.
Router(config)#ephone-dn 2
%LINK-3-UPDOWN: Interface ephone_dsp DN 2.1, changed state to up
Router(config-ephone-dn)#number 123
Router(config-ephone-dn)#exit
Router(config)#ephone-dn 3
%LINK-3-UPDOWN: Interface ephone_dsp DN 3.1, changed state to up
Router(config-ephone-dn)#number 11111
Router(config-ephone-dn)#exit
Commands on Switch for VOIP
Switch(config)#interface range fastEthernet 0/1 - fastEthernet 0/10
Switch(config-if-range)#switchport mode access
Switch(config-if-range)#switchport voice vlan 1

You might also like