Scribd
Upload
36 views

3C Update Olt and Onu Bin

1. The document describes the steps to upgrade the version of an OLT and the versions of connected ONUs. It involves setting the management address of the OLT, uploading the new OLT software to the OLT flash via TFTP, then updating and committing the new ONU software versions on each ONU port. 2. Upgrading an ONU version involves uploading the new ONU software to the OLT flash, using a command to update the software and reboot an ONU on a specific port, then committing the updated version. 3. Successful version upgrades require restarting affected devices to load the new software versions.

Uploaded by

Joe Iglases
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
36 views

3C Update Olt and Onu Bin

1. The document describes the steps to upgrade the version of an OLT and the versions of connected ONUs. It involves setting the management address of the OLT, uploading the new OLT software to the OLT flash via TFTP, then updating and committing the new ONU software versions on each ONU port. 2. Upgrading an ONU version involves uploading the new ONU software to the OLT flash, using a command to update the software and reboot an ONU on a specific port, then committing the updated version. 3. Successful version upgrades require restarting affected devices to load the new software versions.

Uploaded by

Joe Iglases
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

2.

3 Version Upgrade
2.3.1 OLT Version Upgrade
Step 1: Set the management address of OLT.
Switch_config#int vlan 1
/Create interface vlan1 and enter the interface mode of
interface vlan1.
Switch_config#ip address 192.168.0.1 255.255.255.0 /Set ip 192.168.0.1 for interface vlan1.

Meanwhile, make sure the connectivity of PC and OLTs management address.

Step 2: Enable the TFTP server on a PC and set the upload directory
of the TFTP server.

Step 3: Upload the OLT IOS file from PC to the OLT flash.
Switch_config#copy tftp:BDMSU8508_11.0.1D.bin flash:Switch.bin 192.168.0.2
/Upload the IOS file from TFTP server 192.168.0.2 to the flash.
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################

###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
#######################################################
###############
################################################
TFTP: successfully receive 11793 blocks ,6037711 bytes

2.3.1 ONU Version Upgrade


Step1: Upload the ONU IOS file to the OLT flash.
For details, see section 2.3.1.

Step2: Update the ONU IOS file in the OLT flash.


Switch#epon update onu image IEP1208_10.0.2D5.bin int e3/1:1
/update the software version for the ONU of int e3/1:1
Are you sure to update the ONU image(y/n)?y
Please wait for update.....
Switch#Feb 28 10:43:59 check SLOT 3 IOS consistency..........
Feb 28 10:43:59 [SLOT 3]Start update file:ONU_IMAGE...
Feb 28 10:43:59 IEP1208_10.0.2D5.bin for SLOT 3 is diffrent with MSU, update it.....
Feb 28 10:44:27 successful send 2674305 bytes to SLOT 3
Feb 28 10:44:27 [SLOT 3]Update file ONU_IMAGE finished!
Feb 28 10:44:27 [SLOT 3]The image is downloading to the ONU on E3/1:1, Please wait! The
onu will reboot when downloading finished, and then you can check the software version
after re-registration!
Feb 28 10:44:28 SLOT 3 file syn finished
Feb 28 10:44:28 [SLOT 3]All files update finished!
Feb 28 10:44:28 SLOT 3 update OK,consumed time is 29s
Switch#Feb 28 10:44:59 %EPON-ONUDEREG: ONU 00e0.0fcb.bc6a is deregistered on
E3/1:1.

Feb 28 10:44:59 [SLOT 3]%EPON-ONUDEREG: ONU 00e0.0fcb.bc6a is deregistered on


E3/1:1.

Note: After the update of ONU mirror file, the system will automatically reboot and download the
new mirror file.

Step3: Confirm the updated ONU IOS file.


Switch#epon commit-onu-image-update int e3/1:1
/update the mirror file of int e3/1:1ONU
CTC_OAM_ONU_UPGRADE_COMMIT_IMG_REQ
Switch#Feb 28 10:53:04 [SLOT 3]Commit onu image update successfully on E3/11:3!

Note: After ONU updates the mirror file and downloads the new mirror file and restarts, you need
to confirm the updated mirror; or ONU will download and run the previous mirror file at the next
startup.

You might also like