Chapter 2.

Basic MPLS Configuration

Table of Contents
Basic MPLS Configuration .......................................................................... 1
Frame-Mode MPLS Configuration and Verification ..................................................................................................................... 1
Cell-Mode MPLS over ATM Overview, Configuration, and Verification .................................................................................... 15
Command Reference .................................................................................................................................................................... 45

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 1

Return to Table of Contents

Chapter 2. Basic MPLS Configuration

In the first chapter, you were introduced to the MPLS forwarding model in which labels
are used to forward packets for a certain destination network. You were also provided
details on frame- and cell-mode MPLS operation.
In this chapter, the following topics are covered:

Frame-mode MPLS configuration and verification

Licensed by
Alex Hannah

- Basic frame-mode MPLS configuration and verification

- Frame-mode MPLS over RFC 2684 (obsoletes RFC 1483) routed PVC
Cell-mode MPLS over ATM configuration and verification
- Basic cell-mode MPLS configuration and verification

- Configuring cell-mode MPLS with and without virtual circuit merge (VC-merge)
- MPLS over VP tunnels configuration and verification
- Configuring MPLS over ATM using BPX ATM switch and 7200 as label switch
controller (LSC)

Frame-Mode MPLS Configuration and Verification

In frame mode, MPLS uses a 32-bit label that is inserted between the Layer 2 and Layer 3
headers. Layer 2 encapsulations like HDLC, PPP, Frame Relay, and Ethernet are framebased except for ATM, which can operate either in frame mode or cell mode.

Basic Frame-Mode MPLS Overview, Configuration, and Verification

Figure 2-1 shows a frame-based MPLS provider network providing MPLS services to sites
belonging to Customer A. The frame-based provider's network consists of routers R1, R2,
R3, and R4. R1 and R4 function as Edge Label Switch Routers (LSRs) while R2 and R3
serve as LSRs.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 2

Return to Table of Contents

Figure 2-1. Frame-Mode MPLS Provider Network

Figure 2-2 illustrates the configuration flowchart to implement frame-mode MPLS on the
provider network shown in Figure 2-1. The configuration flowchart assumes that IP
addresses are preconfigured where required.
Figure 2-2. Frame-Mode MPLS Configuration Flowchart

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 3

Return to Table of Contents

Basic Frame-Mode MPLS Configuration Steps

The steps to configure frame-mode MPLS are based on the configuration flowchart
outlined in Figure 2-2. Ensure that IP addresses are configured prior to following these
steps:
Step 1. Enable CEFCEF is an essential component for label switching and is
responsible for imposition and disposition of labels in an MPLS network.
Configure CEF globally on routers R1, R2, R3, and R4 by issuing the ip cef
[distributed] command. Ensure that CEF is not disabled on the interface. If
disabled, enable CEF on the interface by issuing ip route-cache cef in
interface mode. Use the distributed keyword in the global configuration
mode for Cisco platform capable of distributed CEF switching. Example 2-1
highlights the configuration to enable CEF on R2. Similarly enable CEF on R1,
R3, and R4.
Example 2-1. Enable CEF

R2(config)#ip cef distributed

R2(config)#do show running-config interface s0/0 | include cef
no ip route-cache cef
R2(config)#interface s0/0
R2(config-if)#ip route-cache cef

Step 2. Configure IGP routing protocolConfigure the IGP routing protocol; in

this case, OSPF. Enable the interfaces on R1, R2, R3, and R4 that are part of
the provider network in OSPF using networkip-address wild-cardmaskareaarea-id command under the OSPF routing process. Example 2-2
highlights the OSPF configuration on R2. Similarly configure OSPF on R1, R3,
and R4.
Example 2-2. Configure IGP Routing Protocol on R2

R2(config)#router ospf 100

R2(config)#network 10.10.10.0 0.0.0.255 area 0

Enabling the label distribution protocol is an optional step. TDP is deprecated,

and by default, LDP is the label distribution protocol. The command mpls
label protocol {ldp | tdp} is configured only if LDP is not the default label
distribution protocol or if you are reverting from LDP to TDP protocol or vice
versa. The command can be configured in the global as well as in the interface
configuration mode. The interface configuration command will, however,
override the global configuration.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 4

Return to Table of Contents

Step 3. Assign LDP router IDLDP uses the highest IP address on a loopback
interface as the LDP router ID. If there is no loopback address defined, the
highest IP address on the router becomes the LDP router ID. To force an
interface to be an LDP router ID, mpls ldp router-idinterface-type
number command can be used. The loopback interface address is
recommended because it always remains up. Configure the loopback 0
interface on the R2 router to be the LDP router ID as shown in Example 2-3.
Repeat the configuration on R1, R3, and R4, assigning the local loopback
interface as LDP router-id.
Example 2-3. Assign LDP Router ID

R2(config)#mpls ldp router-id loopback 0

Step 4. Enable IPv4 MPLS or label forwarding on the interfaceExample

2-4 demonstrates the step to enable MPLS forwarding on the interface.
Example 2-4. Enable MPLS Forwarding

R2(config)#interface serial 0/0

R2(config-if)#mpls ip
R2(config)#interface serial 0/1
R2(config-if)#mpls ip

Verification of Basic Frame-Mode MPLS Operation

The steps to verify the frame-mode MPLS operation are as follows. All verification steps
were performed on Router R2. Outputs of the commands have been truncated for brevity,
and only pertinent lines are depicted:
Step 1. Example 2-5 verifies whether CEF is globally enabled or disabled on the router
by issuing the show ip cef command. As shown in Example 2-5, CEF is
disabled on R2. Example 2-5 shows if CEF is enabled on the router interfaces.
Example 2-5. CEF Verification

R2#show ip cef
%CEF not running
Prefix
Next Hop
Interface
_____________________________________________________________________
R2#show cef interface serial 0/0
Serial0/0 is up (if_number 5)

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Return to Table of Contents

Page 5

(Output truncated)
IP CEF switching enabled
IP CEF Fast switching turbo vector
(Output Truncated)
_____________________________________________________________________
R2#show cef interface serial 0/1
Serial0/1 is up (if_number 6)
(Output Truncated)
IP CEF switching enabled
IP CEF Fast switching turbo vector

Step 2. Verify MPLS forwarding is enabled on the interfaces by issuing the show
mpls interfaces command. Example 2-6 shows that MPLS is enabled on the
serial interfaces. The IP column depicts Yes if IP label switching is enabled on
the interface. The Tunnel column is Yes if LSP tunnel labeling (discussed later
in Chapter 9, "MPLS Traffic Engineering") is enabled on the interface, and the
Operational column is Yes if packets are labeled on the interface.
Example 2-6. MPLS Forwarding Verification

R2#show mpls interfaces

Interface
IP
Serial0/0
Yes (ldp)
Serial0/1
Yes (ldp)

Tunnel
No
No

Operational
Yes
Yes

Step 3. Verify the status of the Label Distribution Protocol (LDP) discovery process
by issuing show mpls ldp discovery. This command displays neighbor
discovery information for LDP and shows the interfaces over which the LDP
discovery process is running. Example 2-7 shows that R2 has discovered two
LDP neighbors, 10.10.10.101 (R1) and 10.10.10.103 (R3). The xmit/recv field
indicates that the interface is transmitting and receiving LDP discovery Hello
packets.
Example 2-7. LDP Discovery Verification

R2#show mpls ldp discovery

Local LDP Identifier:
10.10.10.102:0
Discovery Sources:
Interfaces:
Serial0/0 (ldp): xmit/recv
LDP Id: 10.10.10.101:0
Serial0/1 (ldp): xmit/recv
LDP Id: 10.10.10.103:0

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 6

Return to Table of Contents

Step 4. Issue show mpls ldp neighbor to verify the status of the LDP neighbor
sessions. Example 2-8 shows that the LDP session between R2 and R1
(10.10.10.101), as well as between R2 and R3 (10.10.10.103), is operational.
Downstream indicates that the downstream method of label distribution is
being used for this LDP session in which the LSR advertises all of its locally
assigned (incoming) labels to its LDP peer (subject to any configured access
list restrictions).
Example 2-8. LDP Neighbor Verification

R2#show mpls ldp neighbor

Peer LDP Ident: 10.10.10.101:0; Local LDP Ident 10.10.10.102:0
TCP connection: 10.10.10.101.646 - 10.10.10.102.11012
State: Oper; PIEs sent/rcvd: 26611/26601; Downstream
Up time: 2w2d
LDP discovery sources:
Serial0/0, Src IP addr: 10.10.10.1
Addresses bound to peer LDP Ident:
10.10.10.101 10.10.10.1
Peer LDP Ident: 10.10.10.103:0; Local LDP Ident 10.10.10.102:0
TCP connection: 10.10.10.103.11002 - 10.10.10.102.646
State: Oper; Msgs sent/rcvd: 2374/2374; Downstream
Up time: 1d10h
LDP discovery sources:
Serial0/1, Src IP addr: 10.10.10.6
Addresses bound to peer LDP Ident:
10.10.10.6
10.10.10.103
10.10.10.9

Control and Data Plane Forwarding in Basic Frame-Mode MPLS

Figure 2-3 shows the control and data plane forwarding operation in frame-mode MPLS.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 7

Return to Table of Contents

Figure 2-3. Frame-Mode MPLS Control and Data Plane Operation

Control Plane Operation in Basic Frame-Mode MPLS

Figure 2-3 shows the control plane operation for prefix 10.10.10.101/32 from R1 to R4.
The following steps are performed in the label propagation process for prefix
10.10.10.101/32:
Step 1. Example 2-9 shows that R1 sends an implicit null or the POP label to R2. A
value of 3 represents the implicit-null label. R1 propagates the implicit-null
label to its penultimate Router R2, which performs the POP function in the
data forwarding from R4 to 10.10.10.101/32. If R1 propagates an explicit-null
label, the upstream LSR R2 does not POP the label but assigns a label value of
0 and sends a labeled packet to R2.
Example 2-9. MPLS Label Bindings on R1

R1#show mpls ldp bindings

<output truncated>
tib entry: 10.10.10.101/32, rev 4
local binding: tag: imp-null
remote binding: tsr: 10.10.10.102:0, tag: 16

Step 2. Example 2-10 shows R2 assigning an LSP label 16 to 10.10.10.101/32. This

label value is propagated to R3. This label value is imposed by R3 in the data
forwarding path (for example, a packet originating from R4 to prefix
10.10.10.101/32 on R1).

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Return to Table of Contents

Page 8

Example 2-10. Label Allocation and Distribution Verification on R2

R2#show mpls forwarding-table

Local Outgoing
Prefix
tag
tag or VC
or Tunnel Id
16
Pop tag
10.10.10.101/32
17
Pop tag
10.10.10.8/30
18
Pop tag
10.10.10.103/32
19
19
10.10.10.104/32

Bytes tag
switched
0
0
0
0

Outgoing
interface
Se0/0
Se1/0
Se1/0
Se1/0

Next Hop
point2point
point2point
point2point
point2point

Step 3. Example 2-11 shows that on R3, prefix 10.10.10.101/32 has been assigned a
local label of 17 and an outgoing label of 16. The outgoing label is received from
the Router R2. The local label of 17 has been propagated during label
distribution to Router R4. Label 17 is used by R4 in the data forwarding path
for data destined to prefix 10.10.10.101/32 located on R1 from R4.
Example 2-11. Label Allocation and Distribution Verification on R3

R3#show
Local
tag
16
17
18
19

mpls forwarding-table
Outgoing
Prefix
tag or VC
or Tunnel Id
Pop tag
10.10.10.0/30
16
10.10.10.101/32
Pop tag
10.10.10.102/32
Pop tag
10.10.10.104/32

Bytes tag
switched
0
0
0
0

Outgoing
interface
Se0/0
Se0/0
Se0/0
Se1/0

Next Hop
point2point
point2point
point2point
point2point

Data Forwarding Operation in Basic Frame-Mode MPLS

The following steps are performed in the data forwarding path from R4 to prefix
10.10.10.101/32:
1. As shown in Figure 2-3, R4 imposes label 17 on the data packet originating from R4
destined to 10.10.10.101/32.
2. R3 does an LFIB lookup and swaps label 17 for 16 and forwards that data packet to
R2.
3. R2 receives the data packet from R3, does a penultimate hop pop function, removes
label 16, and forwards the data packet to R1.

Final Device Configurations for Basic Frame-Mode MPLS

The pertinent configurations for the devices in the frame-mode MPLS domain are shown
in Examples 2-12 through Example 2-15.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 9

Return to Table of Contents

Example 2-12. R1 Configuration

hostname R1
!
ip cef
!
mpls ldp router-id Loopback0
!
interface Loopback0
ip address 10.10.10.101 255.255.255.255
!
interface Serial1/0
description Connection to R2
ip address 10.10.10.1 255.255.255.252
mpls ip
!
router ospf 100
network 10.10.10.0 0.0.0.255 area 0

Example 2-13. R2 Configuration

hostname R2
!
ip cef
!
mpls ldp router-id Loopback0
!
interface Loopback0
ip address 10.10.10.102 255.255.255.255
!
interface Serial0/0
description Connection to R1
ip address 10.10.10.2 255.255.255.252
mpls label protocol ldp
mpls ip
!
interface Serial0/1
description Connection to R3
ip address 10.10.10.5 255.255.255.252
mpls label protocol ldp
mpls ip
!
router ospf 100
network 10.10.10.0 0.0.0.255 area 0

Example 2-14. R3 Configuration

hostname R3
!
ip cef
!
mpls label protocol ldp
!
interface Loopback0
ip address 10.10.10.103 255.255.255.255
!
interface Serial0/0
description connection to R4
ip address 10.10.10.9 255.255.255.252
mpls ip
!
interface Serial0/1
description connection to R2

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 10

Return to Table of Contents

ip address 10.10.10.6 255.255.255.252

mpls ip
!
router ospf 100
network 10.10.10.0 0.0.0.255 area 0

Example 2-15. R4 Configuration

hostname R4
!
ip cef
!
mpls label protocol ldp
!
interface Loopback0
ip address 10.10.10.104 255.255.255.255
!
interface Serial1/0
Description connection to R3
ip address 10.10.10.10 255.255.255.252
mpls ip
!
router ospf 100
network 10.10.10.0 0.0.0.255 area 0

Frame-Mode MPLS over RFC 2684 Routed PVC

Frame-mode MPLS can be implemented over RFC 2684 (previously RFC 1483) routed
PVCs. When using PVCs, RFC 2684 specifies the following methods of encapsulation to
carry traffic over ATM AAL5:
VC multiplexing A virtual circuit-based multiplexing method in which each VC
carries one protocol. The user, therefore, defines one PVC per protocol.
LLC/SNAP encapsulation This method multiplexes multiple protocols over a
single ATM virtual circuit.

Figure 2-4 shows the network topology for RFC 2684 routed.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 11

Return to Table of Contents

Figure 2-4. Topology: Frame-Mode MPLS Over RFC 2684 Routed PVCs

Figure 2-5 illustrates the flowchart to configure frame-mode MPLS on the provider
network devices shown in Figure 2-4. The configuration flowchart assumes that IP
addresses are pre-configured where needed.
Figure 2-5. Frame-Mode MPLS Configuration Flowchart

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 12

Return to Table of Contents

Figure 2-6 shows the flowchart for configuring the ATM PVC route on the LS1010 ATM
switch.
Figure 2-6. Configuration Flowchart for LS1010 ATM Switch

Configuration Steps for Frame-Mode MPLS Over RFC 2684 Routed PVC
The steps to configure RFC 2684 bridged encapsulation over MPLS on R1 and R2 are as
follows. Ensure that IP addresses are preconfigured on R1 and R2, as illustrated in Figure
2-4:
Step 1. Follow the steps shown in the "Basic Frame-Mode MPLS Configuration
Steps" section. These steps are the same for frame-mode MPLS over RFC 2684
routed PVC. Follow those steps to configure frame-mode MPLS on R1 and R2:
Step 1. Enable CEF
Step 2. Enable IGP routing protocol
Step 3. Assign LDP router ID
Step 2. Enable IPv4 MPLS or label forwarding on the interfaceConfigure
the ATM PVCs 2/200 on each of the appropriate subinterfaces on R1 and R2.
The encapsulation used on the PVC is ATM aal5snap. Example 2-16 highlights
the steps to configure ATM PVC.
Example 2-16. Configure PVCs on R1 and R2

R1(config)#interface ATM2/0.2 point-to-point

R1(config-subif)# pvc 2/200
R1(config-if-atm-vc)# encapsulation aal5snap
R1(config-if-atm-vc)# mpls ip
_____________________________________________________________________
R2(config)#interface ATM2/0.2 point-to-point
R2(config-subif)#pvc 2/200
R2(config-if-atm-vc)#encapsulation aal5snap
R2(config-if-atm-vc)# mpls ip

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 13

Return to Table of Contents

Configuration of the LS1010 ATM Switch

Configure the core ATM switches A1 and A2 to perform VC mapping from one interface to
another. The PVC is a permanent logical connection that you must configure manually,
from source to destination, through the ATM network. After it is configured, the ATM
network maintains the connection at all times. The configuration of an ingress PVC/
interface mapped to an egress PVC/interface needs to be performed only on one of the
ingress or egress interfaces. Therefore, on ATM switch A1, the configuration is performed
on interface ATM1/0/1 mapping PVC 2/200 to interface ATM1/0/0 PVC 2/200. The same
process is repeated on ATM switch A2, shown in Example 2-17.
Example 2-17. Configure PVC Mapping on A1 and A2
A1(config-if)#interface ATM1/0/1
A1(config-if)# description Connection to A2
A1(config-if)# atm pvc 2 200 interface ATM1/0/0 2 200
_____________________________________________________________________
A2(config-if)#interface ATM1/0/1
A2(config-if)# description connection to A1
A2(config-if)# atm pvc 2 200 interface ATM1/0/0 2 200

Verification Steps for Frame-Mode MPLS Over RFC 2684 Routed PVC
The steps to verify frame-mode MPLS over RFC 2684 (previously RFC 1483) routed PVC
are as follows:
Step 1. Verify the operation of MPLS over RFC 2684 by performing a view of the MPLS
forwarding information base (LFIB), as shown in Example 2-18.
Example 2-18. Verification of LFIB

R1#show mpls forwarding-table

Local Outgoing
Prefix
Bytes tag
Outgoing
Next Hop
tag
tag or VC
or Tunnel Id
switched
interface
36
Pop tag
10.10.10.104/32
0
AT2/0.2
point2point
37
Pop tag
10.10.20.128/30
0
AT2/0.2
point2point
R1#
_____________________________________________________________________
R2#show mpls forwarding-table
Local Outgoing
Prefix
Bytes tag
Outgoing
Next Hop
tag
tag or VC
or Tunnel Id
switched
interface
16
Pop tag
10.10.10.101/32
0
AT2/0.2
point2point
18
Pop tag
10.10.20.192/30
0
AT2/0.2
point2point

Step 2. As shown in Example 2-19, verify connectivity by issuing pings.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 14

Return to Table of Contents

Example 2-19. Verify Connectivity

R1#ping 10.10.10.104
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.101, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
R4#
R2#ping 10.10.10.101
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.101, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
R4#

Final Device Configuration for Frame-Mode MPLS Over RFC 2684 Routed PVC
The final device configuration for R1, A1, A2, and R2 is shown in Example 2-20 through
Example 2-23.
Example 2-20. Configuration of R1
hostname R1
!
ip cef
!
interface Loopback0
ip address 10.10.10.101 255.255.255.255
!
interface Ethernet0
ip address 10.10.20.193 255.255.255.252
!
interface ATM2/0
no ip address
!
interface ATM2/0.2 point-to-point
description connection to A1
ip address 10.10.20.1 255.255.255.252
mpls ip
pvc 2/200
encapsulation aal5snap
!
router ospf 100
network 10.10.0.0 0.0.0.255 area 0

Example 2-21. A1 Configuration

hostname A1
!
interface ATM1/0/0
description connection to R1
!
interface ATM1/0/1
description connection to A2
atm pvc 2 200 interface ATM1/0/0 2 200
!

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 15

Return to Table of Contents

Example 2-22. A2 Configuration

hostname A2
!
interface ATM1/0/0
description connection to R2
!
interface ATM1/0/1
description connection to A1
atm pvc 2 200 interface ATM1/0/0 2 200
!

Example 2-23. R2 Configuration

hostname R2
!
ip cef
!
interface Loopback0
ip address 10.10.10.104 255.255.255.255
!
interface Ethernet0
ip address 10.10.20.129 255.255.255.252
!
interface ATM2/0
!
interface ATM2/0.2 point-to-point
description connection to A2
ip address 10.10.20.2 255.255.255.252
mpls ip
pvc 2/200
encapsulation aal5snap
!
router ospf 100
log-adjacency-changes
network 10.10.0.0 0.0.255.255 area 0

Cell-Mode MPLS over ATM Overview, Configuration, and

Verification
This section introduces you to cell-mode MPLS over ATM configuration. In MPLS over
ATM networks, routers are connected to ATM-based provider networks consisting of ATM
switches that forward data based on virtual circuits (VCs) provisioned on the ATM
switches. Cell-mode MPLS uses the virtual path identifier/virtual channel identifier (VPI/
VCI) fields in the ATM header as the label value.
ATM VCs exist locally (on a link between two adjacent ATM switches or two CPEs) and
have two identifiers: VPI and VCI. These two identifiers are often referred to as a VPI/VCI
pair. VPI and VCI numbers are part of ATM cell headers, and they are, therefore, carried
in each ATM cell. Because there are two identifiers, you can have two different types of
ATM connections: virtual path and virtual channel. This hierarchy allows aggregation of

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 16

Return to Table of Contents

the number of virtual channels into a single pipe (virtual path) between sites that need a
large number of VCs.
The ATM switch is responsible for switching ATM cells on both the VC and VP. When the
ATM switch is configured to switch cells on a VC, it has to look at both VPI and VCI fields
of the cell in order to make a switching decision. Switching is done based on a table
containing (port, VPI, VCI) tuplets for the input and output side of the VC. On Cisco IOS
ATM switches, you can see this table with the show atm vc command. You can also
configure the ATM switch to switch cells based only on the port and VPI number; this is
called VP switching. For VP switching, the ATM switch uses a table consisting of (port,
VPI) pairs for input and output. You can see this table on Cisco IOS ATM switches with
the show atm vp command. When VP switching, the ATM switch uses only the VPI field
of each ATM cell to make a switching decision, which reduces processing time. The same
holds true for cell header rewrites. In VC switching, both VPI and VCI fields of the cell
header are rewritten and possibly changed. However, in VP switching, only VPI fields can
be changed, and the VCI field remains the same end-to-end.

Basic Cell-Mode MPLS Configuration and Verification

Figure 2-7 shows a basic cell-mode MPLS network in which R1 and R2 perform the ATM
Edge LSR function while LS1010 ATM switches A1 and A2 serve as the ATM LSR.
Figure 2-7. Cell-Mode MPLS Network

Basic Cell-Mode MPLS Configuration Flowchart for Edge LSRs

Figure 2-8 shows the configuration flowchart to set up basic cell-mode configuration on
the Edge LSR R1 and R2.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 17

Return to Table of Contents

Figure 2-8. Basic Cell-Mode MPLS Configuration Flowchart for Edge ATM LSR

Basic Cell-Mode MPLS Configuration Flowchart for LSRs

Figure 2-9 shows the configuration flowchart for LSR A1 and A2.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 18

Return to Table of Contents

Figure 2-9. Basic Cell-Mode MPLS Configuration Flowchart for ATM LSR

Basic Cell-Mode MPLS Configuration Steps

The configurations for basic cell-mode MPLS are based on the configuration flowcharts
outlined in Figure 2-8 and Figure 2-9. The functions of the Edge ATM LSRs are performed
by routers R1 and R2, and the ATM switches A1 and A2 function as ATM LSRs in the cellmode MPLS domain.

Configuration Steps for Edge ATM LSR

This section outlines the steps in the configuration of the Edge ATM LSR R1 for ATM or
cell-mode MPLS. Ensure that loopback and interface IP addresses are preconfigured
before following the steps:
Step 1. Enable CEFAs shown in Example 2-24, enable CEF globally. Repeat the
same steps on R2.
Example 2-24. Enable CEF

R1(config)#ip cef

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 19

Return to Table of Contents

Step 2. Configure the IGP routing protocolAs shown in Example 2-25,

configure OSPF as the IGP routing protocol. Repeat the steps on R2.
Example 2-25. Configure IGP for IP Reachability

R1(config)#router ospf 100

R1(config-router)#network 10.10.0.0 0.0.0.255 area 0

Step 3. Configure MPLS forwarding on the interfaceCreate an MPLS

subinterface on the ATM link to the connected ATM switch. Enable MPLS
forwarding on the ATM subinterface. Example 2-26 demonstrates this step.
Example 2-26. Enable MPLS Forwarding

R1(config)#interface atm2/0.1 mpls

R1(config-subif)#description Connection to A1
R1(config-subif)#ip address 10.10.20.1 255.255.255.252
R1(config-subif)#mpls ip
_____________________________________________________________________
R2(config)#interface atm2/0.1 mpls
R2(config-subif)#description Connection to A2
R2(config-subif)#ip address 10.10.20.10 255.255.255.252
R2(config-subif)#mpls ip

Configuration Steps for ATM LSR

This section demonstrates the steps to configure ATM switches A1 and A2. It is assumed
that CEF is enabled on the switches and IP addresses are configured on the appropriate
interfaces.
Step 1. Configure OSPF as the IGP routing protocolExample 2-27
summarizes the step to configure OSPF on A1. Repeat the step on A2.
Example 2-27. Configure IGP for IP Connectivity

A1(config)#router ospf 100

A1(config-router)#network 10.10.0.0 0.0.255.255 area 0

Step 2. Enable MPLS forwarding on the interfaceEnable MPLS forwarding

on the ATM physical interfaces, as shown in Example 2-28.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 20

Return to Table of Contents

Example 2-28. Enable MPLS Forwarding

A1(config)#interface atm1/0/0
A1(config-if)#mpls ip
A1(config)#interface atm 1/0/1
A1(config-if)#mpls ip

Note that no configuration has been made on the MPLS ATM subinterfaces on the Edge
ATM LSRs or LSRs with regards to the control-vc using the mpls atm control-vc
command. This implies that all the control plane information is propagated and exchanged
using the default control VC VPI/VCI values of 0/32. However, the user can change the
control-vc associated on an interface in a cell-mode MPLS network. Changes made to the
VPI/VCI values associated to the control-vc on an LSR interface must also be made on the
connected LSR's interface to enable proper exchange of control plane information.

Verification of Basic Cell-Mode MPLS Configuration

The following steps outline the verification process for cell-mode MPLS operation. All
verifications outlined were performed on Edge ATM LSR R1 and ATM LSR A1:
Step 1. Verify CEF is enabled on the router interfaces on Edge LSR R1, as shown in
Example 2-29.
Example 2-29. Verify CEF Is Enabled on the Interfaces

R1#show cef interface atm2/0

ATM2/0 is up (if_number 12)
<truncated>
IP CEF switching enabled
IP Feature Fast switching turbo vector
IP Feature CEF switching turbo vector

Step 2. As shown in Example 2-30, verify that MPLS forwarding is enabled on the
appropriate interfaces on R1 and A1.
Example 2-30. Verify MPLS Forwarding

R1#show mpls interfaces

Interface
IP
Tunnel
Operational
ATM2/0.1
Yes No
Yes
(ATM tagging)
_____________________________________________________________________
A1#show mpls interfaces
Interface
IP
Tunnel
Operational
ATM1/0/0
Yes No
Yes
(ATM tagging)
ATM1/0/1
Yes No
Yes
(ATM tagging)

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 21

Return to Table of Contents

Step 3. Verify the status of the LDP discovery process by issuing show mpls ldp
discovery. This command displays neighbor discovery information for LDP
and shows the interfaces over which the LDP discovery process is running.
Example 2-31 shows neighbor discovery information and interfaces where
LDP is running on R1 and A1. The xmit/recv field indicates that the interface
is transmitting and receiving LDP discovery Hello packets.
Example 2-31. Verify MPLS LDP Discovery

R1#show mpls ldp discovery

Local LDP Identifier:
10.10.10.101:0
LDP Discovery Sources:
Interfaces:
ATM2/0.1: xmit/recv
LDP Id: 10.10.20.101:1; IP addr: 10.10.20.2
LDP Id: 10.10.20.102:2; IP addr: 10.10.20.6
_____________________________________________________________________
A1#show mpls ldp discovery
Local LDP Identifier:
10.10.20.101:0
LDP Discovery Sources:
Interfaces:
ATM1/0/0: xmit/recv
LDP Id: 10.10.10.101:1; IP addr: 10.10.20.1
ATM1/0/1: xmit/recv

Step 4. Issue show mpls ldp neighbor to verify the status of LDP neighbor
sessions. Example 2-32 shows that the LDP session between R1 and A1 is
operational. Downstream on demand on R1 indicates the downstream on
demand method of label distribution is used for the LDP session between R1
and A1 in which the LSR (R1) advertises its locally assigned (incoming) labels
to its LDP peer, A1, only when A1 requests them.
Example 2-32. LDP Distribution Protocol Neighbor Verification

R1#show mpls ldp neighbor

Peer LDP Ident: 10.10.20.101:1; Local LDP Ident 10.10.10.101:1
TCP connection: 10.10.20.2.38767 - 10.10.20.1.646
State: Oper; PIEs sent/rcvd: 371/366; ; Downstream on demand
Up time: 05:04:40
LDP discovery sources:
ATM2/0.1
_____________________________________________________________________
A1#show mpls ldp neighbor
Peer LDP Ident: 10.10.20.102:2; Local LDP Ident 10.10.20.101:2
TCP connection: 10.10.20.6.11002 - 10.10.20.5.646
State: Oper; PIEs sent/rcvd: 28096/28083; ; Downstream on demand
Up time: 2w3d

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 22

Return to Table of Contents

LDP discovery sources:

ATM1/0/1
Peer LDP Ident: 10.10.10.101:1; Local LDP Ident 10.10.20.101:1
TCP connection: 10.10.20.1.646 - 10.10.20.2.38767
State: Oper; PIEs sent/rcvd: 365/369; ; Downstream on demand
Up time: 05:03:28
LDP discovery sources:
ATM1/0/0

Step 5. Verify OSPF routing table on R4, as shown in Example 2-33.

Example 2-33. Verify OSPF Routing

R1#show ip route ospf

O
O
O
O
O

10.0.0.0/8 is variably subnetted, 7 subnets, 2 masks

10.10.20.4/30 [110/2] via 10.10.20.2, 05:51:42, ATM2/0.1
10.10.20.8/30 [110/3] via 10.10.20.2, 05:51:42, ATM2/0.1
10.10.10.104/32 [110/4] via 10.10.20.2, 05:51:42, ATM2/0.1
10.10.20.101/32 [110/2] via 10.10.20.2, 05:51:42, ATM2/0.1
10.10.20.102/32 [110/3] via 10.10.20.2, 05:51:42, ATM2/0.1

Step 6. Issue ping to 10.10.10.104 from R1 to ensure reachability, as displayed in

Example 2-34.
Example 2-34. Verify Reachability

R1#ping 10.10.10.104
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.104, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms

Control and Data Forwarding Operation in Basic Cell-Mode MPLS Configuration

Figure 2-10 shows the control and data plane forwarding operation in cell-mode MPLS.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Return to Table of Contents

Page 23

Figure 2-10. Control and Data Plane Operation in Cell-Mode MPLS

Control Plane Operation in Basic Cell-Mode MPLS Configuration

The control plane operation shows the label propagation for prefix 10.10.10.101/32 from
R1 to R4. The following steps are performed in the label propagation process for prefix
10.10.10.101/32:
Step 1. Edge ATM LSR R4 requests a label for the 10.10.10.101/32 prefix using the
LDP label mapping request from its downstream neighbor, ATM LSR A2. A2
requests a label for the 10.10.10.101/32 prefix using the LDP label mapping
request from its downstream neighbor, ATM LSR A1. A1 in turn requests a
label for the 10.10.10.101/32 prefix using the LDP label mapping request from
its downstream neighbor, Edge ATM LSR R1. Edge ATM LSR R1 allocates a
label to 10.10.10.101/32, which corresponds to its inbound VPI/VCI value
1/34, modifies the entry in the LFIB corresponding to 10.10.10.101/32, and
sends it to A1 using an LDP reply. Example 2-35 shows the output of show
mpls atm-ldp bindings.
Example 2-35. Label Allocation and Distribution Verification on R1

R1#show mpls forwarding-table

Local Outgoing
Prefix
tag
tag or VC
or Tunnel Id
18
1/35
10.10.10.104/32
25
1/37
10.10.20.8/30
26
1/36
10.10.20.4/30
27
1/38
10.10.20.101/32

Bytes tag
switched
0
0
0
0

Outgoing
interface
AT2/0.1
AT2/0.1
AT2/0.1
AT2/0.1

Next Hop
point2point
point2point
point2point
point2point

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Return to Table of Contents

Page 24

28
1/39
10.10.20.102/32
0
AT2/0.1
point2point
_____________________________________________________________________
R1#show mpls atm-ldp bindings
Destination: 10.10.10.104/32
Headend Router ATM2/0.1 (3 hops) 1/35 Active, VCD=19
Destination: 10.10.20.4/30
Headend Router ATM2/0.1 (1 hop) 1/36 Active, VCD=13
Destination: 10.10.20.8/30
Headend Router ATM2/0.1 (2 hops) 1/37 Active, VCD=15
Destination: 10.10.20.101/32
Headend Router ATM2/0.1 (1 hop) 1/38 Active, VCD=14
Destination: 10.10.20.102/32
Headend Router ATM2/0.1 (2 hops) 1/39 Active, VCD=16
Destination: 10.10.10.101/32
Tailend Router ATM2/0.1 1/34 Active, VCD=18

Step 2. A1 uses the VPI/VCI 1/34 received from R1 as its outbound VPI/VCI value,
allocates a free VC that is mapped to the local inbound VPI/VCI 1/45, and
modifies the LFIB entry for 10.10.10.101/32. A1 then sends VPI/VCI value
1/45 to A2 via an LDP reply. Example 2-36 shows the output of show mpls
atm-ldp bindings. ATM LSR A1 prefix 10.10.10.104/32 has been assigned
a local tag of 1/35 and an outgoing tag of 1/43. The outgoing tag is received
from the downstream ATM LSR A2. During label distribution, the local tag of
1/35 has been propagated upstream to Router R1, which functions as the
outgoing tag for the specific prefix 10.10.10.104/32 on R1.
Example 2-36. Label Allocation and Distribution Verification on A1

A1#show mpls atm-ldp bindings

Destination: 10.10.20.101/32
Tailend Switch ATM1/0/1 1/42
Tailend Switch ATM1/0/0 1/38
Destination: 10.10.20.0/30
Tailend Switch ATM1/0/1 1/43
Destination: 10.10.10.104/32
Transit ATM1/0/0 1/35 Active
Destination: 10.10.20.4/30
Tailend Switch ATM1/0/0 1/36
Destination: 10.10.20.8/30
Transit ATM1/0/0 1/37 Active
Destination: 10.10.20.102/32
Transit ATM1/0/0 1/39 Active
Destination: 10.10.10.101/32
Transit ATM1/0/1 1/45 Active

Active -> Terminating Active

Active -> Terminating Active
Active -> Terminating Active
-> ATM1/0/1 1/43 Active
Active -> Terminating Active
-> ATM1/0/1 1/44 Active
-> ATM1/0/1 1/45 Active
-> ATM1/0/0 1/34 Active

Step 3. A2 uses the VPI/VCI 1/45 received from A1 as its outbound VPI/VCI value,
allocates a free VC that is mapped to the local inbound VPI/VCI 1/44, and
modifies the LFIB entry for 10.10.10.101/32. A2 then sends VPI/VCI value
1/44 to R2 via an LDP reply. Example 2-37 shows the output of show mpls

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Return to Table of Contents

Page 25

atm-ldp bindings. As shown in Example 2-37, ATM LSR A2 prefix

10.10.10.104/32 has been assigned a local tag of 1/43 and an outgoing tag of
1/35. The outgoing tag is received from the downstream Router R4. The local
tag of 1/43 is propagated upstream to ATM LSR A1 and functions as the nexthop tag or outgoing tag for prefix 10.10.10.104/32 on ATM LSR A1.
Example 2-37. Label Allocation and Distribution Verification on A2

A2#show mpls atm-ldp bindings

Destination: 10.10.20.4/30
Tailend Switch ATM1/0/0 1/33
Destination: 10.10.20.101/32
Transit ATM1/0/0 1/34 Active
Destination: 10.10.20.102/32
Tailend Switch ATM1/0/0 1/35
Tailend Switch ATM1/0/1 1/45
Destination: 10.10.20.0/30
Transit ATM1/0/0 1/36 Active
Destination: 10.10.10.104/32
Transit ATM1/0/1 1/43 Active
Destination: 10.10.20.8/30
Tailend Switch ATM1/0/1 1/44
Destination: 10.10.10.101/32
Transit ATM1/0/0 1/44 Active

Active -> Terminating Active

-> ATM1/0/1 1/42 Active
Active -> Terminating Active
Active -> Terminating Active
-> ATM1/0/1 1/43 Active
-> ATM1/0/0 1/35 Active
Active -> Terminating Active
-> ATM1/0/1 1/45 Active

Step 4. Edge ATM LSR R2 uses VPI/VCI value 1/44 received from A2 as its outbound
VPI/VCI value and modifies the entry in the LFIB. Example 2-38 shows the
output of show mpls atm-ldp bindings. As shown in Example 2-38 on
Edge ATM LSR R2, the mpls atm-ldp bindings show the local tag of 1/35
assigned to prefix 10.10.10.104/32. This local tag is propagated upstream to
ATM LSR A2 and functions as the next-hop tag or outgoing tag for prefix
10.10.10.104/32 on A2.
Example 2-38. Label Allocation and Distribution Verification on R2

R2#show mpls forwarding-table

Local Outgoing
Prefix
Bytes tag Outgoing
Next Hop
tag
tag or VC
or Tunnel Id
switched interface
16
1/36
10.10.20.0/30
0
AT2/0.1
point2point
17
1/33
10.10.20.4/30
0
AT2/0.1
point2point
18
1/44
10.10.10.101/32
0
AT2/0.1
point2point
19
1/34
10.10.20.101/32
0
AT2/0.1
point2point
20
1/35
10.10.20.102/32
0
AT2/0.1
point2point
_____________________________________________________________________
R2#show mpls atm-ldp bindings
Destination: 10.10.20.0/30
Headend Router ATM2/0.1 (2 hops) 1/36 Active, VCD=16
Destination: 10.10.20.4/30
Headend Router ATM2/0.1 (1 hop) 1/33 Active, VCD=13

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 26

Return to Table of Contents

Destination: 10.10.20.101/32
Headend Router ATM2/0.1 (2 hops) 1/34 Active, VCD=15
Destination: 10.10.20.102/32
Headend Router ATM2/0.1 (1 hop) 1/35 Active, VCD=14
Destination: 10.10.10.101/32
Headend Router ATM2/0.1 (3 hops) 1/44 Active, VCD=18
Destination: 10.10.10.104/32
Tailend Router ATM2/0.1 1/35 Active, VCD=14

Data Forwarding Operation in Basic Cell-Mode MPLS Configuration

The following steps are performed in the data forwarding path from R4 to prefix
10.10.10.101/32:
Step 1. R4 imposes label 1/44 on the AAL5 cell originating from R4 and destined to
10.10.10.101/32.
Step 2. A2 does an LFIB lookup and swaps label 1/44 with 1/45 and forwards that
AAL5 cell to A1.
Step 3. A1 receives the data packet from A2, does an LFIB lookup, swaps label 1/45
with 1/34, and forwards that AAL5 cell to R1. Penultimate hop popping is not
supported on ATM devices because the label is part of the ATM cell payload
and cannot be removed by ATM switching hardware. Therefore, A1, which is
an ATM device, does not perform any penultimate hop popping function.

Final Device Configurations for Basic Cell-Mode MPLS

Example 2-39 through Example 2-42 outline the pertinent configurations for all the
devices in the cell-mode MPLS domain.
Example 2-39. R1 Configuration
hostname R1
!
ip cef
!
interface Loopback0
ip address 10.10.10.101 255.255.255.255
!
interface ATM2/0
!
interface ATM2/0.1 mpls
description Connection to A1
ip address 10.10.20.1 255.255.255.252
mpls ip
!
router ospf 100
log-adjacency-changes
network 10.10.0.0 0.0.255.255 area 0

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 27

Return to Table of Contents

Example 2-40. A1 Configuration

hostname A1
!
interface ATM1/0/0
description Connection to R1
ip address 10.10.20.2 255.255.255.252
mpls ip
!
interface ATM1/0/1
description Connection to A2
ip address 10.10.20.5 255.255.255.252
mpls ip
!
router ospf 100
network 10.10.0.0 0.0.255.255 area 0

Example 2-41. A2 Configuration

hostname A2
!
interface ATM1/0/0
description connection to R2
ip address 10.10.20.9 255.255.255.252
mpls ip
!
interface ATM1/0/1
description connection to A1
ip address 10.10.20.6 255.255.255.252
mpls ip
!
router ospf 100
network 10.10.0.0 0.0.255.255 area 0
!

Example 2-42. R2 Configuration

hostname R2
!
ip cef
!
interface Loopback0
ip address 10.10.10.104 255.255.255.255
!
interface ATM2/0
!
interface ATM2/0.1 mpls
description connection to A2
ip address 10.10.20.10 255.255.255.252
mpls ip
!
router ospf 100
log-adjacency-changes
network 10.10.0.0 0.0.255.255 area 0

Configuring Cell-Mode MPLS with VC-Merge

The VC-merge feature in cell-mode MPLS allows an ATM LSR to aggregate multiple
incoming flows with the same destination address into a single outgoing flow. Therefore,
Chapter 2. Basic MPLS Configuration
MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 28

Return to Table of Contents

when two Edge LSRs are sending packets to the same destination, the ingress label
mapping to the two Edge LSRs are mapped to a single outgoing label. The number of VCs
required for label switching is greatly reduced as the ATM switch maintains just one
outgoing VC label for each destination prefix. VC-merge reduces the label space that needs
to be maintained by sharing labels for flows toward the same FEC or prefix.
Figure 2-11 shows a cell-mode MPLS network. This is the same as the network shown in
Figure 2-10 except the new Router R3 is added, which is connected to A1. Edge LSRs R1
and R3 share the same label space for the same destination prefixes on Edge ATM LSR
R2.
Figure 2-11. Cell-Mode MPLS Topology for VC-Merge

Configuration Flowchart for Cell-Mode MPLS with VC-Merge

The configuration flowchart for Edge ATM LSR for cell-mode MPLS with VC-merge
remains the same as what was shown for basic cell-mode MPLS (refer to Figure 2-8). The
only difference in the basic cell-mode MPLS configuration block and cell-mode MPLS with
VC-merge for ATM LSR is the inclusion of the command shown in Example 2-43.
Example 2-43. Enabling ATM VC-Merge
A1(config)#mpls ldp atm vc-merge

Depending upon the hardware, the ATM VC-merge capability is enabled by default;
otherwise, this feature is disabled. Please check Cisco Documentation at cisco.com.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 29

Return to Table of Contents

Configuration Steps for Cell-Mode MPLS with VC-Merge on Edge ATM LSR
The configuration steps for cell-mode MPLS with VC-merge on Edge ATM LSR are the
same as what was shown earlier in section "Configuration Steps for Edge ATM LSR."

Configuration Steps for Cell-Mode MPLS with VC-Merge on ATM LSR

The configuration steps for cell-mode MPLS with VC-merge on ATM LSR are the same as
those shown in the section "Configuration Steps for ATM LSR," except that A1 is enabled
with the VC-merge command mpls ldp atm vc-merge.

Final Configuration for Devices in Cell-Mode MPLS with VC-Merge

The configurations for R1, R2, and A2 remain the same as what was shown in the
section "Final Device Configurations for Basic Cell-Mode MPLS." The configurations for
R3 and A1 are shown in Example 2-44 and Example 2-45. Note that the configuration for
A1 does not depict the mpls ldp atm vc-merge command, which implies that the ATM
LSR A1 supports VC-merge functionality by default.
Example 2-44. R3 Configuration (Truncated)
hostname R3
!
ip cef
!
interface Loopback0
ip address 10.10.10.105 255.255.255.255
!
interface ATM2/0
!
interface ATM2/0.1 mpls
description connection to A1
ip address 10.10.20.13 255.255.255.252
mpls ip
!
router ospf 100
network 10.10.0.0 0.0.255.255 area 0

Example 2-45. A1 Configuration (Truncated)

hostname A1
!
interface Loopback0
ip address 10.10.20.101 255.255.255.255
!
interface ATM1/0/0
description Connection to R1
ip address 10.10.20.2 255.255.255.252
mpls ip
!
interface ATM1/0/1
description Connection to A2
ip address 10.10.20.5 255.255.255.252
mpls ip
!
interface ATM1/0/2
description connection to R5
ip address 10.10.20.14 255.255.255.252
mpls ip

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Return to Table of Contents

Page 30

!
router ospf 100
network 10.10.0.0 0.0.255.255 area 0

Verification Steps for Cell-Mode MPLS with VC-Merge on ATM LSR

The following steps outline the verification procedure for cell-mode MPLS over ATM
implementation with VC-merge on the ATM LSRs:
Step 1. Verify if ATM VC-merge is enabled on the ATM LSR by issuing the show mpls
atm-ldp capability command on the ATM LSR. The output of this command
is shown in Example 2-46.
Example 2-46. ATM VC-Merge Capability

A1#show mpls atm-ldp capability

ATM1/0/0
Negotiated
Local
Peer

VPI
Range
[1 - 1]
[1 - 1]
[1 - 1]

VCI
Range
[33 - 16383]
[33 - 16383]
[33 - 65530]

Alloc
Scheme
UNIDIR
UNIDIR
UNIDIR

Odd/Even
Scheme

VC-Merge
IN
OUT
EN
EN
-

ATM1/0/1
Negotiated
Local
Peer

VPI
Range
[1 - 1]
[1 - 1]
[1 - 1]

VCI
Range
[33 - 16383]
[33 - 16383]
[33 - 16383]

Alloc
Scheme
UNIDIR
UNIDIR
UNIDIR

Odd/Even
Scheme

VC-Merge
IN
OUT
EN
EN

Step 2. When VC-merge is implemented on A1, destinations reachable by R1 and R3

via A1 are provided the same next-hop labels. When a lookup of the label
bindings for prefixes on ATM LSR A1 is performed, the same outgoing label
is used for two different incoming labels from two different flows that map to
the same destination prefix. This is shown in Example 2-47. The ATM LSR A1
maps two incoming labels, 1/35 and 1/34, from Edge ATM LSRs R1 and R5,
respectively, to the same outgoing label 1/43 for the destination prefix
10.10.10.104/32 located on R1.
Example 2-47. A1 VC-Merge Verification

A1#show mpls atm-ldp bindings 10.10.10.104 255.255.255.255

Destination: 10.10.10.104/32
Transit ATM1/0/0 1/35 Active -> ATM1/0/1 1/43 Active
Transit ATM1/0/2 1/34 Active -> ATM1/0/1 1/43 Active

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 31

Return to Table of Contents

Configuring MPLS Over ATM Without VC-Merge

In MPLS over ATM without VC-merge, each path (with the same ingress router and same
Forwarding Equivalent Class [FEC]) consumes one label VC on each interface along the
path. This results in unnecessary exhaustion of the already scarce label space.
The network topology remains the same as what was shown in the section "Configuring
Cell-Mode MPLS with VC-Merge." All configurations remain the same except, as shown
in Figure 2-11, where VC-merge is disabled on A1. Example 2-48 highlights the
configuration to disable VC-merge.
Example 2-48. Disabling VC-Merge on A1
A1(config)#no mpls ldp atm vc-merge

Verify MPLS Over ATM Without VC-Merge

As shown in Example 2-49, when VC-merge is disabled on ATM LSR A1, flows to the same
destination are assigned different outgoing VC labels. show mpls atm-ldp bindings on
A1 shows two different outgoing labels, 1/33 and 1/36, are assigned to the data flows from
R3 and R1, respectively, to destination prefix 10.10.10.104/32. Because VC-merge is not
used, one VC is allocated per route as determined by the prefix in the routing table.
Example 2-49. A1: Disabled VC-Merge Verification
A1#show mpls atm-ldp bindings 10.10.10.104 255.255.255.255
Destination: 10.10.10.104/32
Transit ATM1/0/2 1/34 Active -> ATM1/0/1 1/33 Active
Transit ATM1/0/0 1/33 Active -> ATM1/0/1 1/36 Active

MPLS Over VP Tunnels Configuration and Verification

A VP tunnel is a method of linking two private ATM networks across a public network that
does not support SVCs. The VP tunnel provides a permanent path through the public
network. VP tunnels are multiplexing/demultiplexing multiple VCs from multiple
interfaces, or from the same interface, to the VP tunnel interface. When multiplexing, it
changes the VPI field of VCs that goes through the VP to the same as the VPI number on
the VPs. VCI numbers, though, can be arbitrary. However, for specific VCs, the VCI
numbers on both VP tunnel interfaces (originating and terminating) need to be the same.
In this section, you configure VP tunnels on the ATM switches to carry label information
for MPLS over ATM VP tunnels. Figure 2-12 shows an MPLS network using VP tunnels.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 32

Return to Table of Contents

Figure 2-12. MPLS Over VP Tunnels Topology

Configuration Flowchart for MPLS over VP Tunnels on Edge ATM LSR

The basic configuration flowchart for MPLS over VP tunnel is the same as what was shown
in the section "Basic Cell-Mode MPLS Configuration and Verification" (refer to Figure
2-8).

Configuration Flowchart for Creating an ATM PVP on ATM Switch

The configuration flowchart for creating an ATM PVP is shown in Figure 2-13.
Figure 2-13. Configuration Flowchart for MPLS Over VP Tunnel on ATM LSR

Configuration Steps for MPLS over VP Tunnels

Ensure necessary IP addresses are configured prior to following these steps. The steps to
configure MPLS over VP tunnels are as follows:
Step 1. A VP connection is like a bundle of VCs, transporting all cells with a common
VPI, rather than a specific VPI and VCI. A PVP is a permanent VP (like PVC).
Example 2-50 shows how to configure the internal cross-connect (within the
switch router) PVP on switch A1 between interface 1/0/0, VPI = 2 and interface
1/0/1, VPI = 2, and switch A2 between interface 1/0/0, VPI = 2 and interface
1/0/1, VPI = 2.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 33

Return to Table of Contents

Example 2-50. Configure VP Tunnels on ATM Switches

A1(config)#interface ATM1/0/1
A1(config-if)# description Connection to A2
A1(config-if)# no ip address
A1(config-if)# atm pvp 2 interface ATM1/0/0 2
_____________________________________________________________________
A2(config)#interface ATM1/0/1
A2(config-if)# description connection to A1
A2(config-if)# no ip address
A2(config-if)# atm pvp 2 interface ATM1/0/0 2

Step 2. Configure the VP tunnel using mpls atm vp-tunnelvpivc-range {start-ofvci-range-end-of-vci-range} under the MPLS ATM subinterface. Enable
MPLS on the created subinterface, as shown in Example 2-51.
Example 2-51. Configure VP Tunnel on ATM MPLS Subinterface

R1(config)#interface ATM2/0.1 mpls

R1(config-subif)# description Connection to A1
R1(config-subif)# ip address 10.10.20.1 255.255.255.252
R1(config-subif)# mpls atm vp-tunnel 2 vci-range 33-65535
R1(config-subif)#mpls ip
_____________________________________________________________________
R2(config)#interface ATM2/0.1 mpls
R2(config-subif)# description connection to A2
R2(config-subif)# ip address 10.10.20.2 255.255.255.252
R2(config-subif)# mpls atm vp-tunnel 2 vci-range 33-65535
R2(config-subif)#mpls ip

Step 3. Configure IGP for IP connectivity across the VP tunnel on R1 and R2, as shown
in Example 2-52.
Example 2-52. Configure IGP

R1(config)#router ospf 100

R1(config-router)# network 10.10.0.0 0.0.255.255 area 0

Verification Steps for MPLS over VP Tunnels

The steps to verify MPLS over VP tunnels are as follows:
Step 1. Verify operation of PVP on the ATM switches, as shown in Example 2-53.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 34

Return to Table of Contents

Example 2-53. Verify PVP Status

A1#show atm vp
Interface
VPI
Type X-Interface
X-VPI
Status
ATM1/0/0
2
PVP
ATM1/0/1
2
UP
ATM1/0/1
2
PVP
ATM1/0/0
2
UP
_____________________________________________________________________
A2#show atm vp
Interface
VPI
Type X-Interface
X-VPI
Status
ATM1/0/0
2
PVP
ATM1/0/1
2
UP
ATM1/0/1
2
PVP
ATM1/0/0
2
UP

Step 2. Verify OSPF routes on R1 by issuing show ip route ospf. Example 2-54
shows the networks received on R1 from R2.
Example 2-54. Verify OSPF Routes

R1#show ip route ospf

10.0.0.0/8 is variably subnetted, 7 subnets, 2 masks
O
10.10.20.2/32 [110/1] via 10.10.20.2, 00:12:25, ATM2/0.1
O
10.10.10.104/32 [110/2] via 10.10.20.2, 00:12:25, ATM2/0.1
O
10.10.20.128/30 [110/11] via 10.10.20.2, 00:12:25, ATM2/0.1

Step 3. Verify connectivity across the VP tunnel using the ping command, as shown
in Example 2-55.
Example 2-55. Verify Connectivity Using Ping

R1#ping ip 10.10.20.129 source 10.10.20.193

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.20.129, timeout is 2 seconds:
Packet sent with a source address of 10.10.20.193
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms

Final Device Configurations for MPLS over VP Tunnels

The final device configuration for R1, A1, A2, and R2 is shown in Example 2-56 through
Example 2-59.
Example 2-56. R1 Configuration
hostname R1
!
ip cef
!
interface Loopback0
ip address 10.10.10.101 255.255.255.255
!

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 35

Return to Table of Contents

interface Ethernet0
ip address 10.10.20.193 255.255.255.252
!
interface ATM2/0
!
interface ATM2/0.1 mpls
description Connection to A1
ip address 10.10.20.1 255.255.255.252
mpls ip
mpls atm vp-tunnel 2 vci-range 33-65535
!
router ospf 100
network 10.10.0.0 0.0.255.255 area 0

Example 2-57. A1 Configuration

hostname A1
!
interface ATM1/0/0
description Connection to R1
!
interface ATM1/0/1
description Connection to A2
atm pvp 2 interface ATM1/0/0 2
!

Example 2-58. A2 Configuration

hostname A2
!
interface ATM1/0/0
description connection to R2
!
interface ATM1/0/1
description connection to A1
atm pvp 2 interface ATM1/0/0 2
!

Example 2-59. R2 Configuration

hostname R2
!
ip cef
!
interface Loopback0
ip address 10.10.10.104 255.255.255.255
!
interface Ethernet0
ip address 10.10.20.129 255.255.255.252
!
interface ATM2/0
!
interface ATM2/0.1 mpls
description connection to A2
ip address 10.10.20.10 255.255.255.252
mpls ip
mpls atm vp-tunnel 2 vci-range 33-65535
!

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 36

Return to Table of Contents

router ospf 100

network 10.10.0.0 0.0.255.255 area 0

Implementing Cell-Mode MPLS with BPX8600 and 7200 as Label Switch Controller
Cell-mode MPLS can also be implemented by separating the control and data plane
functions of an ATM LSR. The control plane function is performed by a device called the
LSC or label switch controller, and the data plane function can be performed by an ATM
switch such as the BPX8600 Series ATM switches. In the BPX with LSC design, the LSC
is connected to the BPX ATM switch by trunks that can carry PVCs, SVCs, or MPLS Label
VCs (LVCs). The control software is physically located in the LSC that is connected to the
ATM switch by a physical connection also called the virtual switch interface (VSI) control
link. The VSI control link could be an STM-1 link connected to a single port of a broadband
switching module (BXM) linecard on the BPX8600. This is shown in Figure 2-14.
Figure 2-14. BPX with LSC as LSR

In Figure 2-14, the functions control plane is implemented using a BPX+LSC. The figure
outlines a connection from each of the Edge ATM LSRs to the LSC connected to the BPX
switch using LVCs. These signaling LVCs are maintained per LSR that the BPX+LSC is
connected to. In addition, VSI control links are maintained per card on the BPX.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 37

Return to Table of Contents

From a data plane perspective, data label VCs bypass the LSC and are switched using the
BPX ports. Therefore, in the data plane, the traffic via the ATM label switch router traverses
only the BPX ATM switch and not the LSC.
The signaling label VCs are on VPI/VCI values of 0/32 by default and will be crossconnected to a different VCI on the switch control link between the BPX and LSC. One key
thing to note is that the LSC functions as the VSI master and the BPX functions as the VSI
slave.

Configuring BPX+LSC as ATM LSR

This section deals with the configuration of a BPX+LSC as an ATM LSR to implement cellmode MPLS. The topology used to implement this configuration is shown in Figure 2-15.
Figure 2-15. BPX and LSC as ATM LSR: Topology

Figure 2-15 shows the physical connections for this section in which two Edge ATM LSRs
are connected to a BPX 8600 switch. The LSC (7200 router) is also connected on the same
switch. The numbers 2.1, 2.2, and 2.3 in Figure 2-15 pertain to slot.port on the BPX 8600
switch. The only IP addresses shown in this figure are those of the loopbacks on the LSR
and ELSRs. Figure 2-16 shows the Edge ATM LSRs connected to the LSC in the control
plane using the VSI control VCs as well as the signaling LVCs that originate from an
mpls subinterface on the Edge ATM LSR and terminate on an XtagATM interface on the
LSC. The XtagATM interface controls the trunks on the BPX that are connected to other
LSRs.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Return to Table of Contents

Page 38

Figure 2-16. BPX and LSC as ATM LSR: Control Plane

Configuring the BPX

The steps to configure the BPX are as follows:
Step 1. Verify the cards on the BPX by issuing dspcds command. As shown in Example
2-60, the BXM-155 card connects and configures the trunks on the BPX as well as
the appropriate resources on the ports.
Example 2-60. Viewing Cards on BPX

bpxa

1
2
3
4
5
6
7
8

TRM

cisco:1

FrontCard
BackCard
Type
Rev Type Rev
BME-622 KMB SM-2 BD
BXM-155 FJL MM-8 BB
BXM-T3 FJL TE3-12BA
BXM-622 FML SM-2 BD
BXM-155 FAL SM-4 BB
BXM-622 FPH SM-2 BE
BCC-4
HDM LM-2 AC
Empty reserved for Card

BPX 8620
Status
Standby
Active
Active
Standby
Standby
Standby
Active

9
10
11
12
13
14
15

9.2.30

FrontCard
Type
Rev
Empty
Empty
Empty
Empty
Empty
Empty
ASM
ACC

Oct. 8 2004

15:18 MST

BackCard
Type Rev

Status

LMASM AC

Active

Last Command: dspcds

Next Command:

Step 2. Enable the trunks on the ports 2.1, 2.2, and 2.3. This is as shown in Example
2-60. Example 2-61 shows only the command to be used in the "next command"
section to enable the three trunks connecting to the two Edge ATM LSRs as well as
the LSC.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Return to Table of Contents

Page 39

Example 2-61. Configuring Trunks on the BPX (Commands)

Next Command: uptrk 2.1

Next Command: uptrk 2.2
Next Command: uptrk 2.3

When the trunks are configured, view the trunk configuration using the dsptrks
command, as shown in Example 2-62.
Example 2-62. Viewing Trunk Configuration

bpxa
TRK
2.1
2.2
2.3

TRM
Type
OC3
OC3
OC3

cisco:1
Current
Clear Clear Clear -

BPX 8620

9.2.30

Line Alarm Status

OK
OK
OK

Oct. 8 2004

15:26 MST

Other End
-

Last Command: dsptrks

Next Command:

Step 3. Configuration of resources applied to the trunks already configured is performed

using the cnfrsrc command on the BPX, as shown in Example 2-63.
Example 2-63. Configuring Resources

bpxa
TRM
Port/Trunk : 2.1
Maximum PVC LCNS:
Partition 1
Partition State :
Minimum VSI LCNS:
Maximum VSI LCNS:
Start VSI VPI:
End VSI VPI :
Minimum VSI Bandwidth :
VSI ILMI Config
:
VSI Topo Dsc
:

cisco:1

BPX 8620
256
Enabled
600
1500
240
255
105000
0
0

9.2.30

Oct. 8 2004

15:29 MST

Maximum PVC Bandwidth:247207

(Statistical Reserve: 1000)

Maximum VSI Bandwidth :

105000

VSI Ses Ctrlr Id

255

Last Command: cnfrsrc 2.1 256 247207 y 1 e 600 1500 240 255 105000 105000

The command in Example 2-63 can be explained as "configure resources for trunk
2.1 where the maximum PVC LCNs are 256, the maximum PVC bandwidth is
247207; editing of VSI information is enabled, Partition ID is 1 and is enabled; the
maximum VSI LCNs are 600 and the maximum VSI LCNs are 1500; the VSI VPIrange is configured to be between 240255 and the minimum and maximum VSI
bandwidths is 105000."

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Return to Table of Contents

Page 40

Repeat this command to configure resources for trunks 2.2 and 2.3. However, all
trunks need to be part of the same partition (1). When completed, a dsprsrc issued
for the appropriate trunk and partition IDs, as shown in Example 2-64, shows the
resources allocated to the trunk.
Example 2-64. Display Configured Resources

bpxa
TRM
Port/Trunk : 2.2
Maximum PVC LCNS:

cisco:1

BPX 8620
256

Partition 1
Partition State :
Minimum VSI LCNS:
Maximum VSI LCNS:
Start VSI VPI:
End VSI VPI :
Minimum VSI Bandwidth :
VSI ILMI Config
:
VSI Topo Dsc
:

Enabled
512
1500
240
255
105000
0
0

9.2.30

Oct. 8 2004

15:37 MST

Maximum PVC Bandwidth:247207

(Statistical Reserve: 1000)

Maximum VSI Bandwidth :

105000

VSI Ses Ctrlr Id

255

Last Command: dsprsrc 2.2 1

Step 4. MPLS labeled packets use the queues 1014 on each port (one queue per class). To
enable MPLS packet forwarding, configure the queues using the cnfqbin
command. Example 2-65 shows the command to configure the qbin 10 on BPX
trunk 2.2 as well as the output of the configuration.
Example 2-65. Configuring Qbin's on BPX Ports for MPLS

bpxa

TRM

cisco:1

Qbin Database 2.2 on BXM qbin 10

BPX 8620

9.2.30

Oct. 8 2004

15:43 MST

(Configured by User)
(EPD Enabled on this qbin)

Qbin State:
Enabled
Discard Threshold:
65536 cells
EPD Threshold:
95%
High CLP Threshold:
100%
EFCI Threshold:
40%
Last Command: cnfqbin 2.2 10 e n 65536 95 100 40

Step 5. Finally, add an LSC shelf as a VSI master using the addshelf command. In
Example 2-66, the first "1" after "VSI" is the VSI controller ID, which must be set
the same on both the BPX 8650 and the LSC. The default controller ID on the LSC
is "1." The second "1" after "VSI" is the partition ID that indicates this is a controller
for partition 1. The "v" stands for a VSI controller.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Return to Table of Contents

Page 41

Example 2-66. Adding VSI Master Shelf

bpxa

TRM

Trunk

Name

2.2

VSI

cisco:1
BPX 8620 9.2.30
Oct. 8 2004 15:48 MST
BPX 8620 Interface Shelf Information
Type
Part Id
Ctrl Id
Control_VC
Alarm
VPI
VCIRange
VSI
1
1
0
40-54
OK

Last Command: addshelf 2.2 v 1 1 0 40

To verify, perform a dsptrks, and the trunk 2.2 appears with VSI on the other end
column to show that a VSI master systems or device is connected on trunk 2.2, as
shown in Example 2-67.
Example 2-67. Verification of VSI

a
TRK
2.1
2.2
2.3

TRM
Type
OC3
OC3
OC3

cisco:1
Current
Clear Clear Clear -

BPX 8620
Line Alarm Status
OK
OK
OK

9.2.30

Oct. 8 2004

15:51 MST

Other End
VSI(VSI)
-

Configuration of the Label Switch Controller

Configuration of the LSC involves enabling the 7200/7500 series as a LSC for the BPX
shelf and configuration of XTagATM interfaces to control the trunks on the BPX shelf:
Step 1. Configure the ATM interface connected to the BPX trunk 2.2 to be the VSI
control link between the BPX and the 7200/7500. See Example 2-68.
Example 2-68. Configure 7200/7500 Port as a LSC Port

LSC(config)#interface ATM1/0
LSC(config-if)# no ip address
LSC(config-if)# tag-control-protocol vsi

Step 2. Configure the XTagATM interfaces as control links for the trunks 2.1 and 2.3
on the BPX using the extended port command on the LSC, as displayed in
Example 2-69. Note that the numbering of the XTagATM interfaces maps to
the actual trunk ports that they control on the BPX shelf. Therefore, XTagATM
interface 21 controls BPX trunk 2.1, and XTagATM interface 23 controls BPX
trunk 2.3.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Return to Table of Contents

Page 42

Example 2-69. Configure Control Links Using XTagATM Interfaces on LSC

LSC(config)#interface ATM1/0
LSC(config-if)# no ip address
LSC(config-if)# tag-control-protocol vsi
LSC(config-if)#interface XTagATM21
LSC(config-if)# ip address 10.10.10.2 255.255.255.252
LSC(config-if)# extended-port ATM1/0 bpx 2.1
LSC(config-if)# mpls ip
LSC(config-if)#interface XTagATM23
LSC(config-if)# ip address 10.10.10.6 255.255.255.252
LSC(config-if)# extended-port ATM1/0 bpx 2.3
LSC(config-if)# mpls ip

Step 3. Configure OSPF as the IGP on the LSC, and include all interfaces for OSPF
routing. See Example 2-70.
Example 2-70. Configure IGP (OSPF) on LSC

LSC(config)#router ospf 100

LSC(config-router)# log-adjacency-changes
LSC(config-router)# network 10.10.10.0 0.0.0.255 area 0

Step 4. Verify the operation of the VSI control interfaces using the show controllers
vsi status command on the LSC. See Example 2-71.
Example 2-71. Verify VSI Controller Status

LSC#show controllers vsi status

Interface Name
XTagATM21
switch control port
XTagATM23

IF Status
up
n/a
up

IFC State
ACTIVE
ACTIVE
ACTIVE

Physical Descriptor
0.2.1.0
0.2.2.0
0.2.3.0

Configuration of Edge ATM LSRs

The configuration of the Edge ATM LSRs contains the same configuration as that of Edge
ATM LSRs when implementing basic cell-mode MPLS, involving configuration of an MPLS
subinterface under the ATM physical interface and other ATM-TDP parameters. OSPF is
the IGP routing protocol. See Example 2-72.
Example 2-72. Configuration of Edge ATM LSR
ELSR1(config)#interface ATM3/0
ELSR1(config-if)# no ip address
ELSR1(config-if)#interface ATM3/0.1 mpls
ELSR1(config-subif)# ip address 10.10.10.1 255.255.255.252
ELSR1(config-subif)# mpls atm vpi 240-255

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 43

Return to Table of Contents

ELSR1(config-subif)# mpls ip
ELSR1(config)#router ospf 100
ELSR1(config-router)# router-id 10.10.10.101
ELSR1(config-router)# network 10.10.10.0 0.0.0.255 area 0
_____________________________________________________________________
ELSR2(config)#interface ATM1/0
ELSR2(config-if)# no ip address
ELSR2(config-if)#interface ATM1/0.1 mpls
ELSR2(config-subif)# ip address 10.10.10.5 255.255.255.252
ELSR2(config-subif)# mpls atm vpi 240-255
ELSR2(config-subif)# mpls ip
ELSR2(config-subif)#router ospf 100
ELSR2(config-router)# network 10.10.10.0 0.0.0.255 area 0

The key command to be added in Example 2-72 is mpls atm vpi, which defines the VPI
range to be used for the LVCs. This needs to match the configuration of the BPX, as shown
in Example 2-64.

Verification of Cell-Mode MPLS with BPX+LSC Operation

Step 1. Verify TDP neighbor discovery and neighbor status on ELSR1, ELSR2, and LSC.
Note that, because the LSC is only capable of ATM-TDP, the peering process
appears as a TDP neighbor relationship and not a ATM-LDP neighbor
relationship. See Example 2-73.
Example 2-73. TDP Neighbor Verification

ELSR1#show mpls ldp neighbor

Peer TDP Ident: 10.10.10.100:1; Local TDP Ident 10.10.10.101:1
TCP connection: 10.10.10.2.11375 - 10.10.10.1.711
State: Oper; PIEs sent/rcvd: 813/809; Downstream on demand
Up time: 11:39:02
TDP discovery sources:
ATM3/0.1, Src IP addr: 10.10.10.2
_____________________________________________________________________
ELSR1#show mpls ldp discovery
Local LDP Identifier:
10.10.10.101:0
Discovery Sources:
Interfaces:
ATM3/0.1 (tdp): xmit/recv
TDP Id: 10.10.10.100:1; IP addr: 10.10.10.2
_____________________________________________________________________
ELSR2#show mpls ldp neighbor
Peer TDP Ident: 10.10.10.100:2; Local TDP Ident 10.10.10.102:1
TCP connection: 10.10.10.6.11376 - 10.10.10.5.711
State: Oper; PIEs sent/rcvd: 813/813; Downstream on demand
Up time: 11:39:47
TDP discovery sources:
ATM1/0.1, Src IP addr: 10.10.10.6
_____________________________________________________________________
ELSR2#show mpls ldp discovery

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 44

Return to Table of Contents

Local LDP Identifier:

10.10.10.102:0
Discovery Sources:
Interfaces:
ATM1/0.1 (tdp): xmit/recv
TDP Id: 10.10.10.100:2; IP addr: 10.10.10.6
_____________________________________________________________________
LSC#show tag-switching tdp neighbor
Peer TDP Ident: 10.10.10.101:1; Local TDP Ident 10.10.10.100:1
TCP connection: 10.10.10.1.711 - 10.10.10.2.11375
State: Oper; PIEs sent/rcvd: 813/816; ; Downstream on demand
Up time: 11:42:08
TDP discovery sources:
XTagATM21
Peer TDP Ident: 10.10.10.102:1; Local TDP Ident 10.10.10.100:2
TCP connection: 10.10.10.5.711 - 10.10.10.6.11376
State: Oper; PIEs sent/rcvd: 816/815; ; Downstream on demand
Up time: 11:42:06
TDP discovery sources:
XTagATM23
_____________________________________________________________________
LSC#show tag-switching tdp discovery
Local TDP Identifier:
10.10.10.100:0
TDP Discovery Sources:
Interfaces:
XTagATM21: xmit/recv
TDP Id: 10.10.10.101:1; IP addr: 10.10.10.1
XTagATM23: xmit/recv
TDP Id: 10.10.10.102:1; IP addr: 10.10.10.5

Step 2. Verify MPLS label exchange on the Edge LSRs, as shown in Example 2-74.
Example 2-74. MPLS Label Mapping/Exchange Verification

ELSR1#show mpls atm-ldp bindings

Destination: 10.10.10.4/30
Headend Router ATM3/0.1 (1 hop) 240/38 Active, VCD=21
Destination: 10.10.10.100/32
Headend Router ATM3/0.1 (1 hop) 240/40 Active, VCD=22
Destination: 10.10.10.102/32
Headend Router ATM3/0.1 (2 hops) 240/42 Active, VCD=23
Destination: 10.10.10.101/32
Tailend Router ATM3/0.1 240/33 Active, VCD=19
Tailend Router ATM3/0.1 240/35 Active, VCD=20
_____________________________________________________________________
ELSR2#show mpls atm-ldp bindings
Destination: 10.10.10.0/30
Headend Router ATM1/0.1 (1 hop) 240/38 Active, VCD=22
Destination: 10.10.10.100/32
Headend Router ATM1/0.1 (1 hop) 240/40 Active, VCD=23
Destination: 10.10.10.101/32
Headend Router ATM1/0.1 (2 hops) 240/42 Active, VCD=24
Destination: 10.10.10.102/32

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Return to Table of Contents

Page 45

Tailend Router ATM1/0.1 240/33 Active, VCD=20

Tailend Router ATM1/0.1 240/35 Active, VCD=21

Step 3. Verify IGP connectivity, as illustrated in Example 2-75.

Example 2-75. Verification of IGP Connectivity

ELSR1#show ip route ospf

10.0.0.0/8 is variably subnetted, 6 subnets, 3 masks
O
10.10.10.4/30 [110/3] via 10.10.10.2, 12:14:50, ATM3/0.1
O
10.10.10.102/32 [110/4] via 10.10.10.2, 12:14:50, ATM3/0.1
O
10.10.10.100/32 [110/2] via 10.10.10.2, 12:14:50, ATM3/0.1
__________________________________________________________________________
ELSR2#show ip route ospf
10.0.0.0/8 is variably subnetted, 5 subnets, 2 masks
O
10.10.10.0/30 [110/3] via 10.10.10.6, 12:15:17, ATM1/0.1
O
10.10.10.100/32 [110/2] via 10.10.10.6, 12:15:17, ATM1/0.1
O
10.10.10.101/32 [110/4] via 10.10.10.6, 12:15:17, ATM1/0.1
__________________________________________________________________________
LSC#show ip route ospf
10.0.0.0/8 is variably subnetted, 5 subnets, 2 masks
O
10.10.10.102/32 [110/3] via 10.10.10.5, 12:15:37, XTagATM23
O
10.10.10.101/32 [110/3] via 10.10.10.1, 12:15:37, XTagATM21

Step 4. Confirm connectivity using ping between ELSRs, as shown in Example 2-76.
Example 2-76. Verification of Reachability

LSR1#ping 10.10.10.102
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.102, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4

Command Reference
Command
Router(config)#ip cef [distributed]

Router(config-if)#ip route-cache cef

Description
Enables CEF operation. Use the
distributed keyword for distributed
switching platforms in which line cards
maintain an identical copy of the FIB and
adjacency tables. The line cards perform
the forwarding function between port
adapters, relieving the route processor of
involvement in the switching operation.
Enables CEF on the interface.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.

Chapter 2. Basic MPLS Configuration

Page 46

Command
Router(config-if)#mpls ip
Router(config)#router ospfprocess-id
Router(config-router)#networkip-address wild-card maskareaarea-id
Router(config-router)#no auto-summary
Router(config)#router isisprocess-id
Router(config-router)#netnetwork-entity-title
Router(config)#interfacetype number
Router(config-if)#ip router isisprocess-id
Router(config)#mpls label protocol {ldp | tdp}
Router(config-if)#mpls label protocol {ldp | tdp}

Return to Table of Contents

Description
Enables MPLS forwarding on the
interface.
OSPF IGP configuration.

ISIS IGP configuration.

Enables the preferred label distribution

protocol as either TDP or LDP on the
chassis or per interface.
Router(config)#no mpls ip propagate-ttl [forwarded | local]
Disables IP to label TTL mapping when a
packet enters an MPLS-enabled domain.
Router(config)#mpls ldp router-id {interface | ip-address} [force]
Configuring the IP address or a specific
interface as the router ID for the label
distribution protocol. Use the force
keyword for the configuration to take
effect on a router to override earlier
router ID selection or configuration.
Router(config)#mpls label rangemin-label-value max-label-value [staticmin- Defining label range.
label-value max-label-value]
Router(config-if)#mpls mtubytes
Defining the MPLS MTU per interface.
Router(config)#interface atmnumber.sub-interface-numbermpls
Configuring a tag-switching subinterface
on an Edge ATM LSR for cell-mode MPLS
label forwarding.
Router(config-subif)# mpls atm control-vcvpi-value vci-value
Configuring the control-vc parameters
for protocol information exchange
(control plane). Default value for controlvc is VPI/VCI of 0/32.
Router(config-subif)# mpls atm vpistart-vpi-value [-vci-value]
Configuring MPLS ATM VPI range
(default: 1-1).
Router(config)#mpls atm ldp vc-merge
Enabling VC-merge on ATM LSR.
Router(config)#tag-switching atm maxhopsvalue
Sets maximum hops for bindings from
ATM cell-mode domain.
Router(config)#mpls atm vp-tunnelvpi-value [vci-value-range]
Identifies the subinterface as a VP tunnel
with specified VPI values.

Chapter 2. Basic MPLS Configuration

MPLS Configuration on Cisco IOS Software By Umesh Lakshman, Lancy Lobo, - CCIE No.
Prepared for Alex Hannah, Safari ID: [email protected]
4690 ISBN: 1587051990 Publisher: Cisco Press
Print Publication Date: 2005/10/17
User number: 1727602
2008 Safari Books Online, LLC. This PDF is made available for personal use only during the relevant subscription term, subject to the Safari Terms of Service. Any other use
requires prior written consent from the copyright owner. Unauthorized use, reproduction and/or distribution are strictly prohibited and violate applicable laws. All rights reserved.