Scribd
Upload
793 views

3 1 1 A Vex Inputsoutputs

VEX Activity 3.1. Inputs and Outputs - VEX Procedure 1. Start the "ROBOTC for VEX Cortex and PIC" software. 2. Connect the testbed to the computer using the USB A-A cable. 3. Set up the motors and sensors. 4. Power on the Cortex. 5. View motor and sensor debugger windows.

Uploaded by

api-272055202
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
793 views

3 1 1 A Vex Inputsoutputs

VEX Activity 3.1. Inputs and Outputs - VEX Procedure 1. Start the "ROBOTC for VEX Cortex and PIC" software. 2. Connect the testbed to the computer using the USB A-A cable. 3. Set up the motors and sensors. 4. Power on the Cortex. 5. View motor and sensor debugger windows.

Uploaded by

api-272055202
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

RobotC

Activity 3.1.1 Inputs and Outputs VEX


Procedure
1. Start the ROBOTC for VEX Cortex and PIC software.
2. Connect the testbed to the computer using the USB A-A cable.
3. Set up the motors and sensors.
a. Open a New File
b. Set platform and communications method:
i. Click View > Preferences > Detailed Preferences.
ii. In the Platform tab, click the drop down under Platform Type, choose
VEX 2.0 Cortex. Natural Language should appear in the platform type
window.
iii. Make sure under Communication Port, it says Automatic. Note that this
can be changed to USB to ensure that the PC communicates to the
Cortex through the USB cable.
iv. Click OK.
v. Robot > Platform Type > Natural Language
c. Click File, Save As, select the folder that your teacher designated, then name
the file A3_1_1.
d. Complete the Project Title, Team Members, Date, and Section.
e. Click Motors and Sensors Set up.
i. Under the Standard Models Tab
ii. Select Configuration POE + CIM Testbed

4. Save the file in the same location used earlier, A3_1_1.


5. Obtain the teachers approval before proceeding to the next step.
6. Power on the Cortex.
7. View motor and sensor debugger windows.
a. Click Robot.
b. Click Compile and Download Program. Leave the Debug window
open.
c. Click Robot, Debug Windows, then Motors.
d. If there is not a Sensor and Motors tab available at the bottom of the
window, add them through the next steps. Click Robot, Debug
Windows, then Sensors.
e. Increase the debugger window area at the bottom to view the motor
and sensor values as shown below. Note that this window can be
viewed any time by clicking Robot then Debugger.
8. Fill in the Table
2012 Project Lead The Way, Inc.
POE Activity 3.1.1 Inputs and Outputs VEX Page 1

Directions

Left

Enter several values ranging from -127 to


127, then press Enter on the keyboard or
click away from the value entry window.

Observations
(include threshold power setting for the motor to turn)
Right

Motor/Sensor

Motor
Change the line follower immediate
environment and observe the effect on
the lineFollower value. Use a dark and
light color within 1/4 - 1/8 in. to see the
change in the sensor value.

Line Follower
Change the potentiometer setting and
observe the effect on the potentiometer
value. Rotate the potentiometer to
change the sensor input. Do not force
the potentiometer beyond the CW and
CCW physical stops.

Potentiometer

Calculate the angle change between


whole number values in your
engineering notebook. Use the
protractor below to measure an angle.
Change the limit switch environment and
observe the effect on the limitSwitch
value.

Limit Switch
Change the bumper switch environment
and observe the effect on the
bumpSwitch value.
Bumper Switch
Change the optical encoder environment
and observe the effect on the quad
value. Rotate the optical encoder. Note
that there is no CW or CCW physical
stop therefore it can be turned
indefinitely in a direction.
Optical Encoder
Enter a 0 value, then press Enter on the
keyboard or elsewhere in the dialog
window. Did the LED respond as you
expected?
Green LED

Enter a 1 value, then press Enter on the


keyboard or click away from the value
entry window. Did the LED respond as
you expected?

2012 Project Lead The Way, Inc.


POE Activity 3.1.1 Inputs and Outputs VEX Page 2

Enter several values ranging from -127


to 127, then press Enter on the
keyboard or click away from the value
entry window.
Calculate the angle change between
whole number values in your
engineering notebook. Use the
protractor above to measure an angle.
Servo Motor
Enter several values ranging from -127
to 127, then press Enter on the
keyboard or click away from the value
entry window. This allows the value to
be updated. Note that the flashlight
needs a negative value in the debugger
window.
Flashlight
Change the ultrasonic environment with
a solid object in front of the ultrasonic
sensor. Observe the effect on the sonar
value.

Ultrasonic
Change the light sensors immediate
environment by activating the flashlight
and shine it on the light sensor. Use
your hand to shield the light to the
sensor to change the sensor input.
Observe the effect on the lightSensor
value.
Light Sensor

2012 Project Lead The Way, Inc.


POE Activity 3.1.1 Inputs and Outputs VEX Page 3

You might also like