Scribd
Upload
47 views

IP10 CLI Commands

This document provides instructions for configuring an IP-10 device, including how to: 1. Set the device configuration to default values and reset the unit. 2. Show the current alarm status and most severe alarm. 3. Check and update the date and time settings. 4. Enable or disable protection. 5. Set the transmit and receive frequencies. 6. Mute the transmit function. 7. Check transmit and receive signal levels. 8. View radio unit serial number, part number, and software version. 9. Enable radio unit RF loopback and IF loopback tests.

Uploaded by

arunssthoali
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
47 views

IP10 CLI Commands

This document provides instructions for configuring an IP-10 device, including how to: 1. Set the device configuration to default values and reset the unit. 2. Show the current alarm status and most severe alarm. 3. Check and update the date and time settings. 4. Enable or disable protection. 5. Set the transmit and receive frequencies. 6. Mute the transmit function. 7. Check transmit and receive signal levels. 8. View radio unit serial number, part number, and software version. 9. Enable radio unit RF loopback and IF loopback tests.

Uploaded by

arunssthoali
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

IP-10 Quick Startup Guide Doc Rev0.

17
PROPRIETARY
19. Set to Default Configuration
IP-10:/> /management/mng-services/cfg-service/set-to-default

You are about to set the unit configuration to its default values.This operation
will take effect only after a unit reset.Are you sure? (yes/no):no

22. Showing current Alarm


IP-10:/> /management/mng-services/alarm-service/alarm-current/show

Date&Time Severity AlarmName Origin TextIP-10:/> get /management/mngservices/alarm-service/alarm-current/most-severe

cleared
25. Check and update Date and Time
IP-10:/> get management/mng-services/time-service/time-and-date

27-11-2008,11:42:38IP-10:/> set management/mng-services/time-service/timeand-date 27-11-2008,11:50:01

33.Protection Enable Disable


IP-10:/> get platform/mate-idu/protection-admin

disableIP-10:/> set platform/mate-idu/protection-admindisable enableIP-10:/>


set platform/mate-idu/protection-admin enable

IP-10 Quick Startup Guide Doc Rev0.18


PROPRIETARY
35. Set TX/RX Frequency
IP-10:/> get radio/rfu/tx-freq

14515000IP-10:/> set radio/rfu/tx-freq 14515000

IP-10:/> get radio/rfu/rx-freq

14935000IP-10:/> set radio/rfu/rx-freq 14935000

36. Mute TX
IP-10:/> get radio/rfu/mute-tx


disableIP-10:/> set radio/rfu/mute-txdisable enableIP-10:/> set radio/rfu/mute-tx
enable

37. Check TX/RX LEVEL


IP-10:/> get radio/rfu/tx-level-status

22IP-10:/> get radio/rfu/rx-level

-39
38. Check RFU Serial ,Part No and Software
IP-10:/> get radio/rfu/serial-number

FC527553IP-10:/> get radio/rfu/part-number

IP-10:/> get radio/rfu/software-version-number

C1.64_B5
39.RFU RF LooPBack
IP-10:/> get radio/rfu/rfu-rf-loopback

offIP-10:/> set radio/rfu/rfu-rf-loopbackoff onIP-10:/> set radio/rfu/rfu-rf-loopback


on

40.RFU IF LoopBack

IP-10 Quick Startup Guide Doc Rev0.19


PROPRIETARY
IP-10:/> get radio/rfic/if-loopback

OffIP-10:/> set radio/rfic/if-loopbackoff onIP-10:/> set radio/rfic/if-loopback on

You might also like