0% found this document useful (0 votes)
11 views1 page

90-010001003 R100 RescueStep

The document provides instructions for using the RescueStep Safety Device. It describes 3 steps: 1) creating a pullout loop by opening the Velcro closure, 2) securing the loop to the D-ring on a harness, and 3) pulling out the RescueStep ladder and placing feet in the stirrups to support the body after a fall. The RescueStep is small, lightweight, and stays out of the way until needed to relieve pressure on the body from harness straps. It has webbing rated at 2000 lbs minimum and a working load of 310 lbs maximum.

Uploaded by

Victor
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
11 views1 page

90-010001003 R100 RescueStep

The document provides instructions for using the RescueStep Safety Device. It describes 3 steps: 1) creating a pullout loop by opening the Velcro closure, 2) securing the loop to the D-ring on a harness, and 3) pulling out the RescueStep ladder and placing feet in the stirrups to support the body after a fall. The RescueStep is small, lightweight, and stays out of the way until needed to relieve pressure on the body from harness straps. It has webbing rated at 2000 lbs minimum and a working load of 310 lbs maximum.

Uploaded by

Victor
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

AO Safety/SafeWaze Fall Protection

Technical Data Sheet

RescueStep Safety Device


Step 3

Pull RescueStep loop through lower


slot on D-Ring , then pull bag back
through the loop, cinch loop down.

Step 2

Stirrup

After securing to D-ring, to use


pull out RescueStep ladder, and
allow to drop down, put feet in
stirrup straps to allow relieving pressure on body from harness straps.

R100
Doc 90-010001003

To create pullout loop,


open Velcro closure,
pull out a small
amount of webbing as
a loop, reclose Velcro
fastener. Leave loop
exposed for use.

Step 1
Velcro Closure
and pull out loop
Loop for
Belt attachment
R100 RescueStep with pull out loop created..

RescueStep ladder deployed

Use:

Provides a method of supporting body after a fall.


Place loop on harness D-ring by placing loop
through slot in D-ring, pull bag back through the
loop and cinch it to the side of the D-ring slot.
Open bag by pulling apart the Velcro fastener on
bottom of bag, or pulling on pullout loop, which allows the ladder to be pulled or fall out. Create pullout loop as noted above. Place feet in stirrups of the
ladder for support.
Construction:
-Webbing: 1 Red Polyester Fabric
-Total length of stretched out when used is approx.
70 inches from D-ring attachment point.
Webbing:
-All Webbing is rated at 2000 lbs. minimum.
Specification:
-Working load 310 lbs max.

Features:
Small, lightweight, easily accessed, does not put weight
on body when used. Stays out of way until needed.
Weight:
<0.25 lbs

WARNING!
Failure to read and follow these instructions on the use of this
product could result in serious personal injury or death. Training and instruction review should be repeated at regular intervals. This product must be used in strict compliance with local,
state, and federal OSHA regulations.
1.
2.
3.
4.
5.

Use only with ANSI & OSHA compliant fall arrest systems.
This product is not intended to be permanently
installed.
This product must be installed in accordance with all instructions.
All product must be inspected before and after each use.
All products which have been subjected to a fall or other
damaging incident must be removed from service and destroyed.

8001 Woodland Dr Indianapolis, IN 46278 Customer Service :Phone (800) 560-1094 Fax (800) 560-1275

You might also like