Scribd
Upload
64 views

Simple Column Base Plates How To

This document discusses the design of column base plates, which connect steel columns to concrete foundations. It describes three loading scenarios that can be applied to base plates: 1) axial load only, 2) axial load and moment that do not cause uplift, and 3) axial load and moment that do cause uplift. For each scenario, it provides equations to calculate the required base plate size and thickness to withstand the loads. Anchor bolts are also designed to resist tensile forces from moments that cause uplift. The document focuses on designing for axial load only using a fillet weld connection between the column and base plate.

Uploaded by

Logeswaran Raji
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
64 views

Simple Column Base Plates How To

This document discusses the design of column base plates, which connect steel columns to concrete foundations. It describes three loading scenarios that can be applied to base plates: 1) axial load only, 2) axial load and moment that do not cause uplift, and 3) axial load and moment that do cause uplift. For each scenario, it provides equations to calculate the required base plate size and thickness to withstand the loads. Anchor bolts are also designed to resist tensile forces from moments that cause uplift. The document focuses on designing for axial load only using a fillet weld connection between the column and base plate.

Uploaded by

Logeswaran Raji
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

STEEL DESIGN

COLUMN BASE PLATES

SFS

How to Design Column Base Plates


The function and purpose of column base plates are to provide a spread and distribution of column loads
from the steel column to the weaker concrete footing. The base plate acts as an intermediate stress
distributor in a similar way the concrete footing distributes load from the footing to the softer soils
below. When the column load contains a moment, the base plate may require design to ensure uplift of
the base plate does not occur which is achieved by designing anchor bolts to resist the tensile forces.
Base plate design typically involves an iterative procedure to solve for unknowns which can be time
consuming without a useful tool such as a formatted spreadsheet.
A wide variety of base plate connection details are possible for the designer to employ, particularly
when detailing a connection required to resist both axial load and moment. To provide focus within this
report, a discussion of possibilities will be presented, however, the spreadsheet developed will focus on
a single connection arrangement with a unidirectional load case.
Base plates typically sit atop a concrete footing, although other possibilities such as masonry, timber,
and stiff soil foundations may be possible. This report considers concrete foundations only. To
accommodate alternate foundation types, the user can easily incorporate modification of the principals
presented.
Three categories of loading are possible on base plates which are conveniently separated for analysis
and programming purposes. Each load scenario requires slightly different methods for calculating
stresses within the steel and concrete and requires attention to specific design issues.

Load Scenario I:
This load scenario involves the application of direct axial load to the base plate with no corresponding
moment in the column. As a result stress acting on the base plate is uniform over the surface and thus is
the simplest case of the three to analyze.

simple_column_base_plates_how_to.docx

3/27/2012

PAGE 1 OF 6

STEEL DESIGN

COLUMN BASE PLATES

SFS

Under this load scenario, we are primarily concerned with sizing the base plate to transfer a uniform
load to the concrete that is low enough to prevent bearing failure of the concrete footing. Additionally,
we require a design check on the stress within the base plate to ensure yielding of the base plate does not
occur at the cantilever support of the base plate.

The stress acting on the concrete (p) is readily calculated by:


p = Cf/Ap
where Cf=factored compression load
Ap=BD=area of the base plate in plan
This stress is checked against the factored bearing resistance of the concrete (fc) which is calculated
from:
fc = 0.85cfc
Where c=resistance factor for concrete
fc=28 day compressive strength of concrete
By equating these two expressions, the area of the base plate can be established from:
Ab = Cf/(0.85cfc)
An approximation of the design stresses can be made to simplify the calculation of the base plate
thickness by treating the concrete stress as uniform load acting over the cantilever portion of the base
plate. The cantilever lengths n and m are assumed fixed at their origin and their lengths are defined as
shown in the diagram below.

simple_column_base_plates_how_to.docx

3/27/2012

PAGE 2 OF 6

STEEL DESIGN

COLUMN BASE PLATES

SFS

Considering a 1mm wide strip of plate cantilevered over a length of n or m we can show that the
applied load (Mf) is expressed by:
Mf = p m2 (or) p n2
And the element resistance may be expressed as:
Mr = Z Fy
By equating Mf = Mr we can solve for the plate thickness (t) shown as the maximum thickness of:
__________
__________
2
t = (2 p m / Fy) or (2 p n2/ Fy)

Load Scenario II:


Load scenario II is similar to load scenario I but is distinguished by having a moment in the column
which produces a linearly varying load distribution over the surface of the contact area. It is limited to
load distributions that remain in compression over the entire surface of the base plate. In other words, it
is limited to relatively small moments that dont cause uplift of the base plate from the concrete surface
at any point along the base plate. With these definitions in place, we can design base plates falling into
this category in the same manner as category I, with the exception that we need to determine the peak
pressure and distribution of load.
Given a compression load Cf and moment Mf in the column, we can establish the maximum and
minimum bearing pressures on the plate with the following formulae;
pmax = Cf/Ap + Mf/S
pmin = Cf/Ab Mf/S
where S = 1/6 B D2

simple_column_base_plates_how_to.docx

3/27/2012

PAGE 3 OF 6

STEEL DESIGN

COLUMN BASE PLATES

SFS

Once these pressures have been established, we can confirm that this is a Load Scenario II by ensuring
pmin>0.
The plate plan dimensions can be determined by ensuring pmax is less than the allowable bearing stress
in the concrete.
pmax < 0.85 c fc
The required plate thickness can be determined in a similar manner to Load Scenario I, with the
exception of modifying the load as trapezoidal rather than uniform.

Load Scenario III:


Load Scenario III is similar to Load Scenario II with the exception that the moment is large enough to
cause tension or uplift on one side of the base plate. Anchor bolts are required to withstand these tensile
loads and prevent uplift on the bearing plate. The analysis of this load condition is analogous to
reinforced concrete design where the anchor bolts act as the tensile reinforcing and a compressive stress
block of depth a forms a resisting moment couple with the tensile reinforcing.

simple_column_base_plates_how_to.docx

3/27/2012

PAGE 4 OF 6

STEEL DESIGN

COLUMN BASE PLATES

SFS

The tensile capacity of the bolts (Tr) and the compressive resistance of the concrete (Cr), which form the
resisting couple, can be expressed as;
Tr = 0.75 Ab Fu
Cr = 0.85 c fc a B
Summing the forces in the vertical direction gives;
Cf + Tr = Cr
or,
Cf + 0.75 Ab Fu = 0.85 c fc a B
Taking moments about the center line of the bolts gives;
Cf (d-1/2 D) + Mf = Cr (d - a)
or,
Cf (d-1/2 D) + Mf = 0.85 c fc a B (d - a)
The above set of equations represents 2 independent equations and 4 unknowns. A formatted
spreadsheet can be used conveniently to solve the unknowns by first estimating d, B, and D and then

simple_column_base_plates_how_to.docx

3/27/2012

PAGE 5 OF 6

STEEL DESIGN

COLUMN BASE PLATES

SFS

solving for a using the first equation and then substituting a into the second equation and solving for
D. The appropriate value of D can be solved by an iterative method.

ConnectionDetailsandDesign
Several common base plate connection details exist and are largely dependent on the loading condition
required on the base plate. Anchor bolts are typically provided regardless of loading condition, as
erection loads require the use of nominal sized bolts. The connection detail of the base plate to the
column can be, in its simplest form, a fillet weld connecting the two components. When larger moments
are present, a combination of stiffening plates and welds can be used. The figures below demonstrate
some typical connection details.

(A) Typical Details For Moments about Column Strong Axis

(B) Possible Detail for Moments about Column Weak Axis


Because of the large possibility of arrangements, this report will focus the discussion and spreadsheet
calculations to a connection consisting of fillet welds connecting column to base plate and anchor bolts
without stiffeners connecting base plate to concrete.

simple_column_base_plates_how_to.docx

3/27/2012

PAGE 6 OF 6

You might also like