International Journal of Electrical & Computer Sciences IJECS Vol: 9 No: 10

99310-1414 IJECS-IJENS @ International Journals of Engineering and Sciences IJEN

S
37
Abstract— This paper demonstrates a novel method which enable
users to control their home appliances and systems from remote
using a cell phone-based interface. To access the control unit, the
user should send an authentication code (DTMF) along with the
required/desired function/action to his/her home control system
via Global Sytem for Mobile communication(GSM). Upon being
properly authenticated, the cell phone-based interface at home
(control unit) would relay the commands to a microcontroller
that would perform the required function/action, and return a
function completion code that would be sent to the source of the
original command (user’s cell phone).
Index Terms— Decoder, DTMF, GSM, HACS, Microcontroller.
I. INTRODUCTION
The aim of the proposed system is to develop a cost effective
solution that will provide controlling of home appliances
remotely and enable home security against intrusion in the
absence of homeowner. The system provides availability due
to development of a low cost system. The home appliances
control system with an affordable cost was thought to be built
that should be mobile providing remote access to the
appliances and allowing home security. Though devices
connected as home and office appliances consume electrical
power. These devices should be controlled as well as turn on
/off if required. Most of the times it was done manually. Now
it is a necessity to control devices more effectively and
efficiently at any time from anywhere. In this system, we are
going to develop a cellular phone based home/office appliance
C. K. Das, is a faculty member of the Electrical and Electronic
Engineering(EEE) Department, Chittagong University of Engineering and
Technology, Chittagong-4349, Bangladesh. (e-mail: [email protected]).
M. Sanaullah, is a faculty member of the Electrical and Electronic
Engineering(EEE) Department, Chittagong University of Engineering and
Technology, Chittagong-4349, Bangladesh. (e-mail: [email protected]).
H. M. G. Sarower was the undergraduate student of the Electrical and
Electronic Engineering Department, Chittagong University of Engineering
and Technology, Chittagong-4349, Bangladesh.
(e-mail: [email protected]).
M. M. Hasan was the undergraduate student of the Electrical and
Electronic Engineering Department, Chittagong University of Engineering
and Technology, Chittagong-4349, Bangladesh.
(e-mail: [email protected]).
controller [6], [9]. This system is designed for controlling
arbitrary devices, it includes a cell phone (not included with
the system kit, end user has to connect his/her cell phone to
the system) which is connect to the system via head set. To
active the cellular phone unit on the system a call is to be
made and as the call is answered, in response the user would
enter a two/three digit password to access the system to
control devices. As the caller press the specific password, it
results in turning ON or OFF specific device. The device
switching is achieved by Relays [10]. Security preserved
because these dedicated passwords owned and known by
selected persons only. For instance, our system contains
an alarm unit giving the user a remote on/off
mechanism, which is capable of informing up to five
different numbers over telephony network about the
nature of the event [8].
II. SYSTEM DEVELOPMENT
In this system we developed the overall method in two way.
First one is that the targeted devices can be controlled by
sending DTMF [2] (dual tone multi frequency) sent by user
.Another way is that targeted devices can be controlled by
voice messages.
A. Block Diagram
Figure1: Block diagram of the system using DTMF.
In this system, there is a control unit/module. The control unit
is able to connect to the cellular network automatically, to
receive DTMF [8] and will be able to decode for password
identification and instructions to be sent to the
Development of a cell phone based remote control
system: an effective switching system for controlling
home and office appliances.
C. K. Das, M. Sanaullah, H. M. G. Sarower and M. M. Hassan
International Journal of Electrical & Computer Sciences IJECS Vol: 9 No: 10
99310-1414 IJECS-IJENS @ International Journals of Engineering and Sciences IJEN
S
38
microcontroller. The microcontroller [5] within the control
unit will issue the command to the electrical appliances
through a simple control circuit.
B. Circuit Diagram
Figure2:circuit diagram(1) for the system.
Figure3: circuit diagram (2) for the system.
In the circuit diagram, the system’s mechanism has described.
Here, a cell phone is connected in the control unit via headset.
When a call is made the cell phone in the control unit auto
answered. Then password is being pressed. These DTMF
decoded by a dedicated decoder MT-8870 (shown in Figure2:
circuit diagram (1) for the system).Then decoded output sent
to the microcontroller, which issues command to control
devices connected to it(shown in Figure3: circuit diagram (2)
for the system). Device switching is performed by relay.
C. Voice Message Circuit
The circuit diagram for the voice message unit is shown
in Fig4.When the microcontroller detects a triggering
signal from the scanned units, the numbers recorded on
the SIM card of the mobile phone are called sequentially
and the MC activates the voice message unit. The MC
also sends a deactivation signal when the recorded
message is played back. This operation continues in the
same manner until the last call is performed. The
speaker output of the ISD is connected to the cellular
phone speaker so that the recorded message is directly
heard by the receiving end of the phone that has been
called.
Figure4: Circuit diagram for voice message.
D. The DTMF Generation And Decoding
DTMF is Short for Dual Tone Multi frequency and the
system used by touch-tone telephones. DTMF assigns a
specific frequency (consisting of two separate tones) to each
key so that it can easily be identified by a microprocessor.
Figure5: Typical DTMF keypad
International Journal of Electrical & Computer Sciences IJECS Vol: 9 No: 10
99310-1414 IJECS-IJENS @ International Journals of Engineering and Sciences IJEN
S
39
DTMF generation is a composite audio signals of two tones
between the frequency of 697Hz and 1633Hz [2], [3]. The
DTMF keypad is arranged such that each row will have it’s
own unique tone frequency and also each column will have
it’s own unique tone. The figure-5 is a representation of the
typical DTMF keypad and the associated row/column
frequencies. The tone frequencies were selected such that
harmonics and intermodulation products will not cause an
unreliable signal. The DTMF spectrum is shown in figure-6.
Figure6: Dual Tone Multi Frequency(DTMF)spectrum.
As the above frequency spectrum illustrates, each tone must
fall within the proper bandpass before a valid decoding will
take place. If one tone falls outside the bandpass spectrum, the
decoder will become unreliable or not operate at all.
The purpose of DTMF decoding is to detect sinusoidal signals
in the presence of noise. In many cases, the DTMF decoder IC
interfaces with a microcontroller. Here it is logocal that the
microcontroller should not be used to decode the sinusoids.
Because the typical microcontroller based decoder requires an
A/D converter. In addition, the signal processing associated
with the decoding is usually beyond the scope of the
microcontroller s capabilities. So the designer is forced to use
the dedicated IC or upgrade the microcontroller to perhaps a
more costly digital signal processor.
The theory is quite similar to the "classical" signal processing
technique[4]. One brute force way to detect DTMF signals is
to digitize the incoming signal and compute 8 DFT s (discrete
fourier transforms) centered around the 8 DTMF composite
frequencies. DFT s are preferred over FFT s because the
frequencies are not equally spaced (in fact, they are
logarithmically spaced). In its simplest form, the DFT goes
something like so:
N
DFT(x) = Σ x(k) W(k)………………………………(1)
where x(k) are the time samples and W(k) is the infamous
kernal function:
W(k) = e(j2πfk/N) = cos(2πfk/N)+ jsin(2πfk/N)……………(2)
It means that multi
lying the sam
les by sine waves and
cosine waves and adding them together the W(k) can be
found. This will yield eight com
lex numbers. The
magnitudes of these numbers give the information roughly
that how much energy is
resent for each frequency of the
in
ut signal. In other words, we have com
uted the frequency
s
ectrum at the 8 DTMF com
osite frequencies. The reason
why this works so well is because of the "orthogonality" of
the sine waves. In other words, this ha

ens if the DFT is

erformed on two sine waves as shown in the following
equation:
DFT = Σ[sin(f1t) sin(f2t)] ……………………………….(3)
From equation (3), it is clear that we will get the result as a
"large" number if the two frequencies are the same and a
"small" number or zero if they're different.
"DFT" With quare waves[4]
The orthogonality conce
t a

lies equally well to square
waves too. In fact, it's even easy to illustrate with A CII art.
Let us consider the two exam
les as given below:
1)
Figure7: Waveform Of Exam
le1.
2)
Figure8: Waveform Of Exam
le2.
In the first exam
le(figure7), the two square waves have the
same frequency and
hase. When the individual sam
les are
"multi
lied" and summed together, we get a large number:
25. In the second case(figure8), the square waves differ in
frequency by a factor of two. Again as ex
ected, when we
"multi
ly" the individual sam
les and add them u
we get a
small number: 2. If we look closely, we'll notice that the
multi
lication is really an exclusive OR o
eration.
DFT In Quadrature Form[4]
In the DFT, both the sine and cosine waves are used. The two
ty
es of wave are obviously related by 90 degree
hase shift.
An analogously shifted square wave is needed for the DTMF
decoding too. The reason is that it's
ossible to end u
with a
small sum-of-
roducts even if the two waveforms have the
same frequency. This idea can be cleared with the exam
le of
figure-9.
International Journal of Electrical & Com
uter ciences IJEC  Vol: 9 No: 10
99310-1414 IJEC -IJEN  @ International Journals of Engineering and ciences IJEN

40
Figure9: Quadrature Form of Wave.
On the other hand, the DFT o
eration is a dot
roduct
o
eration also. We can imagine the signal and the kernals as
vectors whose indices are the sam
le number. The vectors
could be very large, e.g. 4096 sam
les.
ignal trength Calculation of DFT
If the DFT's are com
uted with sine and cosines, then the
signal strength of a
articular frequency is easily ascertained
with hel
of following equation:
strength ≡√( real(DFT)2 + imaginary(DFT)2) …………..(4)
In other words, the result of a DFT is a com
lex number when
the com
lex kernal is used. And the magnitude of a com
lex
number is the square root of the sum of the real
art squared

lus the imaginary
art squared. This is a cumbersome
o
eration that we would rather avoid. The square root of the
sum of the squares normalization is called the "square norm".
It is a subset of the general class of normed linear s
aces
called the "
-norm". In our case, the linear s
ace consists of
two com
onents: the real and imaginary
arts of the DFT. The

-norm for our case is
strength≡ P√(abs(real(DFT))
+ abs(imaginary(DFT))
) …(5)
And this is the same as the square norm when
is 2.
Now if
is 1, we end u
with an extremely sim
le formula,
the 1-norm:
strength ≡√abs(real(DFT)) + abs(imaginary(DFT))……….(6)
Digitization
rocess of +1 and -1 OR +1 and 0:
o far we've been digitizing to +1 and -1. However, in a real

rogram we'll
robably want to digitize to +1 and 0 since
these are the numbers which are most comfortable for
microcontroller o
eration. The next
oint is how does this
im
act the DFT calculations. u

ose we have two square
waves that are digitized to +1 and - 1. What will ha

en to
their dot
roduct if we digitize them to +1 and 0 instead. Let
f1 and f2 be the two square waves as like below:
f1 = -1 or +1 and f2 = -1 or +1
For the conversion from +1 and – 1 to 1's and 0's:
q1 = (f1 + 1)/2 => f1 = 2q1 –
1……………………………….(7)
q2 = (f2 + 1)/2 => f2 = 2q2 –
1……………………………….(8)
o, q1 and q2 re
resent the re-digitized f1 and f2 square
waves. Now the dot
roduct:
DFT = Σ f1.f2 ≡Σ(2q1 - 1) .(2q2 - 1)
= (4q1q2 - 2q2 - 2q1 + 1)
= 4 Σq1q2 - 2 Σq2 - 2 Σq1 + Σ 1………………..(9)
The last term evaluates N. In other words, 1+1+1+ ... +1 = N.
The middle two terms require a closer examination. Assume
that f1 and f2 contain no DC com
onent:
N
Σ f1 = 0………………………………………………(10)
0
Then the sum of q1 is:
Σq1 = Σ (f1 + 1)/2
= 0 + N/2 = N/2…………………………………(11)
imilarly, the sum of q2 is N/2. Combining these results it can
be shown that:
f1.f2 = 4 Σ q1.q2 - Σ2N/2 - Σ2N/2 + N
= Σ4(q1.q2) - N………….………………………….(12)
Therefore, in conclusion, we can say that the digitization with
0's and 1's is essentially the same as digitizing with +1's and -
1's. But a new "DC" term of N has been introduced and the
dot
roduct has been scaled which are the only differences [4].
Decoding Process
In DTMF there are 16 distinct tones. Each tone is the sum of
two frequencies: one from a low and one from a high
frequency grou
[2], [3]. There are four different frequencies
in each grou
. Most of our
hones only use 12 of the
ossible
16 tones. If we observe our
hone, there are only 4 rows (R1,
R2, R3 and R4) and 3 columns (C1, C2 and C3). In case of
some mobile
hones, it may be vary. The rows and columns
select frequencies from the low and high frequency grou

res
ectively. The exact value of the frequencies are listed in
Table bellow:
TABLE I
Low and High Frequencies election
Each key is s
ecified by its row and column locations. For
exam
le the "2" key is row 0 (R1) and column 1 (C2). Thus
using the above table, "2" has a frequency of 697 + 1336 =
2033 Hz. The "9" is row 2 (R3) and column 2 (C3) and has a
frequency of 852 + 1477 = 2329 Hz.
E. The Program Flowcharts
The main
rogram executed on the MC
(microcontroller) includes three units. The PIC 16F84A
International Journal of Electrical & Com
uter ciences IJEC  Vol: 9 No: 10
99310-1414 IJEC -IJEN  @ International Journals of Engineering and ciences IJEN

41
microcontroller [7] is used to control the whole system. The
first unit contains the initializations and sequential
monitoring of the equi

ed sensor devices. The second

art of the
rogram
erforms the tele
hone calls. Finally,
the last
art contains the interru
t subroutine. When the
main
rogram starts to execute, the MC’s serial
communication band is set to the cellular phone’s
communication rate (i.e. 9600 bit/sec). Afterwards a
password and control sequence is accepted from the
calling user. At the same time, the ports, which will be,
used as either input or output ports are along with the
identification of the registers. Afterwards the system
enters a loop to wait alarm activation. Details of this can
be observed in Fig. 10.
Figure10: Main program flowchart
In the main program, the user can also be directed to
switching subroutine that performs switch-on and switchoff
for three different home appliances.
Figure: Main program flowchart
Figure11: Device control subroutine.
In Fig. 11 the operation structure of switching device
control flowchart is given. In the event of an alarm, -a
burglar’s entrance either to the premises or detection of
a fire- the initial response of the system is activation of a
buzzer. Alarm calls subroutine shown in figure 12.
Figure12: Alarm calls subroutine.
International Journal of Electrical & Computer ciences IJEC  Vol: 9 No: 10
99310-1414 IJEC -IJEN  @ International Journals of Engineering and ciences IJEN

42
III. RE ULT AND ANALY I 
A. uccessful Authentication With G M Network
The G M [1] receiver has tested for successful
communication with network. This test will includes
automation and consistency of the connection and will be
conducted in the following way:
1) The cellular phone dials the G M receiver’s number
2) Once connection is established a DTMF will be sent to
the G M receiver.
3) The G M receiver will e given DTMF to be transferred
to the decoder
The DTMF received will be observed on both end to verify its
consistency.
Result: The G M receiver and transmitter both established a
successful communication over G M network.
B. Proper Decoding
Proper decoding of the remote user’s command and issuance
of the equivalent command to the controlled device will be
perfomed. A simulated instruction will be feed to the
microcontroller communication port.
1) The output command at the input/output interface with
the corresponding controlled device will be observed.
2) The i/o (input/output) command’s voltage will be tested
to meet the levels required to actuate the individual
devices.
Result: Proper decoding of DTMF have completed and
microcontroller causes the proper voltage to be observed at
the desired devices control interfaces.
C. Password Authentication
The password will test for proper operation.
1) A simulated mix of correct and incorrect password will
be sent to the microcontroller.
2) The response of the microcontroller will be observed for
each of the inputted passwords.
Result: Microcontroller grants access to all the right
passwords.
Figure13: (HAC ) Home and Office appliance control system.
An standard Home and Office appliance control system
(HAC ) is shown in figure8.
IV. CAPABILITY OF IMPLEMENTATION IN BANGLADE H
In Bangladesh, almost one fifth of the total population use
cell phone. Moreover, the G M service providers in this
country provide their services at cheap rate. Considering this
cell phone can be an effective element so that the home and
office appliances may be controlled by wireless
device.Devices are directly connected to the power system
causes a huge power loss because they are not controlled
(turning on./off) properly. As usual, devices connected as
home and office appliances are controlled manually most of
the time. Each devices being turned on/off by a individual
switch. Therefore, operator will needed to control them. This
would time consuming and not reliable switching because of
forgetful mind of human being. Users will be capable to use
system this to control their home appliances by using their
wireless devices (cell phone).Though the user can remote
access to the system, which ensures proper controlling of
devices thereby saving of power. Moreover, Users are
comprised of owners, who own the system; administrators,
who are responsible for managing and configuring the system
and the police/fire department personnel, who are contacted in
case of an emergency can utilizes this system as an effective
method.
V. FACTOR  TO BE CON IDERED TO IMPLEMENT THE Y TEM
1) The receiver must reside in a location where a signal
with sufficient strength can be obtained
2) The only person who can communicate with the control
module is the person who will be successfully
authenticated
3) Only devices with electrical controlling input ports will
be possible targets for controlling.
4) The receiver must have a power source (12V) attached at
all times.
5) Operation of the controlling unit is only possible through
a cell phone with DTMF capabilities and voice message.
V. EVALUATING THE Y TEM REGARDING THE CO T
TABLE II
Cost evaluation of the system
Component name Number Cost in TK
Resistance 12 12.00
Capacitance 4 8.00
Diode 4 6.00
LED 4 8.00
Cristal oscilator 2 20.00
IC Regulator 1 12.00
AC/DC Adapter 1 120.00
Microcontroller 1 220
Connecting wire 1feet 3.00
Relay 1 30.00
Cell phone set NOKIA-1650 3300.00
Breadboard 2 480.00
Total =4219.00Tk only
= $ 62 (in dollar)
International Journal of Electrical & Computer ciences IJEC  Vol: 9 No: 10
99310-1414 IJEC -IJEN  @ International Journals of Engineering and ciences IJEN

43
If we take 69 Taka per U.  dollar then we can find the
approximate cost estimation of the system in international
currency. The cost estimation of our system in Bangladeshi
currency is around 4219.00 BD Taka. o if we convert it to
U.  dollars, it would be around 62 U.  dollar ($) which is
very reasonable.
_____________________________
 U  dollar ($) 1 = Taka (Tk) 69
VI. FURTHER TUDY
1) Possibility of confirming the devices initial condition
(status) using short messaging system( M )
2) Though mobile in the control panel required to be
charged, therefore charging system should be automated
which meant a timer can be implemented so that mobile
can be charged after a certain period and disconnected
from the charger when not required.
3) The system can be expanded to provide such control over
the GPR . In this way, the capabilities of the internet can
be combined with the capabilities of our physical line
free communication system. Furthermore, by adding a
closed loop control facility, the system capabilities can be
improved.
VII. CONCLU ION
Mobile phones have become an indispensable part of our life.
Our system uses a controller and a cellular phone for its
operations. The systems can be used as a test bed for any
application that requires on-off switching based applications.
Wireless controlled home appliances in the comforts of any
environment will revolutionize our way of living. Controlling
appliances remotely by a cell phone will one day become a
reality and one should give thanks to the capabilities of
HAC . HAC  might one day become a standard system in
the new homes to come.
ACKNOWLEDGMENT
The authors would like express gratitude to all the persons
who gave their kind assistance during the experiment specially
to Dr. Al Mansur , assistant professor Dept. of Electrical and
Electronic Engineering and Technology (CUET), Chittagong,
Bangladesh.
REFERENCE 
[1] G M Y TEM URVEY , tudent text, EN/LZT 1233321, R5B
revised upgrade edition. p. 192.
[2] Dual-tone multi-frequency, Available:
http://en.wikipedia.org/wiki/Dual-tone_multi-frequency
[3] chenker, L., “Pushbutton Calling with a Two-Group Voice-Frequency
Code” - The Bell system technical journal (I N 0005-8580) vol:39
iss:1 pp:235-255, 1960
[4] DTMF decoding, Available:
http://www.dattalo.com/technical/theory/dtmf.html
[5] “Microcontroller Technology:16F84A”, prentice hall , 7th edition,
page32, 2002
[6] I. Coskun and H. Ardam, “A Remote Controller for Home and Office
Appliances by Telephone”, IEEE Trans. Consumer Electron. , vol. 44,
no. 4, pp. 1291- 1297, November 1998
[7] PIC16F84A microcontroller data sheet, Available:
http://ww1.microchip.com/downloads/en/devicedoc/35007b.pdf
[8] Daldal Nihat, “G M Based ecurity and Control ystem” (In Turkish),
M. c. Term Project, Gazi University, Ankara, 2003.
[9] E. Wong, “A Phone-Based Remote Controller For Home And Office
Automation”, IEEE Trans.Consumer Electron. , vol. 40, no. 1, pp. 28-
33, February 1995.
[10] Relay Information, Available:
http://en.wikipedia.org/wiki/Relay
[1]
C. K. DA  (Choton Kanti Das) was born at
Chittagong in Bangladesh on 5th september,
1982. He obtained his B. c. Degree from
Electrical and Electronic Engineering (EEE)
Department of Chittagong University of
Engineering and Technology (CUET),
Chittagong-4349, Bangladesh, in January,
2006.
He was the LECTURER of the Electrical and Electronic Engineering (EEE)
department in Premier University (PU), Chittagong, Bangladesh, from 13,
March 2006 to 13, January 2008. After then he joined as a LECTURER at the
Electrical and Electronic Engineering (EEE) department of Chittagong
University of Engineering and Technology (CUET), Chittagong, Bangladesh.
Now he is working as a faculty member of EEE department in CUET. He has
interest in the Microprocessor Application in control system.
Mr. Das is now Associate Member of the Engineers Institution, Bangladesh
(IEB).
[2] M. anaullah was born at Kishoreganj in
Bangladesh on 27th March, 1986. He obtained
his B. c. Degree from the department of
Electrical and Electronic Engineering (EEE)
of Chittagong University of Engineering and
Technology (CUET), Chittagong-4349,
Bangladesh, in August, 2008.
He joined as a LECTURER at the Electrical
and Electronic Engineering (EEE) department
of Chittagong University of Engineering and
Technology (CUET), Chittagong, Bangladesh
at 2nd eptember, 2008. Now he is working as a faculty member of EEE
department in CUET. He’s field of interest is Digital ystem Design.
Mr. anaullah is now Associate Member of the Engineers Institution,
Bangladesh (IEB).
[3] H. M. G. arower Obtained his B. c. Degree from the Electrical and
Electronic Engineering Department, Chittagong University of Engineering
and Technology, Chittagong-4349, Bangladesh. He has interest in control
system.
[4] M. M. Hasan is the undergraduate student of the Electrical and Electronic
Engineering Department, Chittagong University of Engineering and
Technology, Chittagong-4349, Bangladesh. He is very much interested in
control system.