NUMBER NAME DEFAULT CHANGED TO

d001 Output Freq d001 READ ONLY

d002 Commanded Freq d002 READ ONLY
d003 Output Current d003 READ ONLY
d004 Output Voltage d004 READ ONLY
d005 DC Bus Voltage d005 READ ONLY
d006 Drive Status d006 READ ONLY
d007 Fault 1 Code d007 READ ONLY
d008 Fault 2 Code d008 READ ONLY
d009 Fault 3 Code d009 READ ONLY
d010 Process Display d010 READ ONLY
d012 Control Source d012 READ ONLY
d013 Contrl In Status d013 READ ONLY
d014 Dig In Status d014 READ ONLY
d015 Comm Status d015 READ ONLY
d016 Control SW Ver d016 READ ONLY
d017 Drive Type d017 READ ONLY
d018 Elapsed Run Time d018 READ ONLY
d019 Testpoint Data d019 READ ONLY
d020 Analog In 0-10V d020 READ ONLY
d021 Analog In 4-20mA d021 READ ONLY
d024 Drive Temp d024 READ ONLY
P031 Motor NP Volts P031 DRIVE RATING
P032 Motor NP Hertz P032 "60.0"
P033 Motor OL Current P033 2XDRIVE RATING
P034 Minimum Freq P034 0.0 Hz
P035 Maximum Freq P035 60 Hz.
P036 Start Source P036 "0" KEYPAD
P037 Stop Mode P037 "0" RAMP, C.F.
P038 Speed Reference P038 "0" DRIVE POT
P039 Accel Time 1 P039 10.0 SEC.
P040 Decel Time 1 P040 10.0 SEC.
P041 Reset To Defalts P041 IDLE State
A051 Digital In1 Sel A051 PRESET FREQ
A052 Digital In2 Sel A052 PRESET FREQ
A055 Relay Out Sel A055 READY/FAULT
A056 Relay Out Level A056 "0.0"
A067 Accel Time 2 A067 20.0 SEC
A068 Decel Time 2 A068 20.0 SEC
A069 Internal Freq A069 60.0 Hz.
A070 Preset Freq 0 A070 0.0 Hz.
A071 Preset Freq 1 A071 5.0 Hz.
A072 Preset Freq 2 A072 10.0 Hz.
A073 Preset Freq 3 A073 20.0 Hz.
A078 Jog Frequency A078 10.0 Hz.
A079 Jog Accel/Decel A079 10.0 Sec.
A080 DC Brake Time A080 0.0 Sec.
A081 DC Brake Level A081 Drive Rated x 0.05
A082 DB Resistor Sel A082 "0" Disabled
A083 S Curve % A083 "0" Disabled
A084 Boost Select A084 "8"5%;ex.5 HP"7"2.5%
A088 Maximum Voltage A088 Drive Rating
A089 Current Limit A089 Drive Rating x 1.5
A090 Motor OL Select A090 "0" no derate
A091 PWM Frequency A091 4.0 kHz.
A092 Auto Rstrt Tries A092 "0" Disabled
A093 Auto Rstrt Delay A093 1.0 Sec.
A094 Start At PowerUp A094 "0" Disabled
A095 Reverse Disable A095 "0" Reverse Enabled
A096 Flying Start En A096 "0" Disabled
A097 Compensation A097 "1" Electrical
A098 SW Current Trip A098 0.0 Disabled
A099 Process Factor A099 "30.0"
A100 Fault Clear A100 "0" Ready/Idle
A101 Program Lock A101 "0" Unlocked
A102 Testpoint Sel A102 "400"
A103 Comm Data Rate A103 "3" 9600
A104 Comm Node Addr A104 "100"
A105 Comm Loss Action A105 "0" Fault
A106 Comm Loss Time A106 5.0 Sec.
A107 Comm Format A107 "0" RTU 8-N-1
A110 Anlg In 0-10V Lo A110 "0%"
A111 Anlg In 0-10V Hi A111 "100%"
A112 Anlg In 4-20mA Lo A112 "0.0%"
A113 Anlg In 4-20mA Hi A113 "100%"
A114 Slip Hertz @ FLA A114 2 Hz.
A115 Process Time Lo A115 "0.0"
A116 Process Time Hi A116 "0.0"
NUMBER NAME DEFAULT CHANGED TO
d001 Output Freq d001 READ ONLY
d002 Commanded Freq d002 READ ONLY
d003 Output Current d003 READ ONLY
d004 Output Voltage d004 READ ONLY
d005 DC Bus Voltage d005 READ ONLY
d006 Drive Status d006 READ ONLY
d007 Fault 1 Code d007 READ ONLY
d008 Fault 2 Code d008 READ ONLY
d009 Fault 3 Code d009 READ ONLY
d010 Process Display d010 READ ONLY
d012 Control Source d012 READ ONLY
d013 Contrl In Status d013 READ ONLY
d014 Dig In Status d014 READ ONLY
d015 Comm Status d015 READ ONLY
d016 Control SW Ver d016 READ ONLY
d017 Drive Type d017 READ ONLY
d018 Elapsed Run Time d018 READ ONLY
d019 Testpoint Data d019 READ ONLY
d020 Analog In 0-10V d020 READ ONLY
d021 Analog In 4-20mA d021 READ ONLY
d022 Output Power READ ONLY
d023 Output Power Factor READ ONLY
d024 Drive Temp d024 READ ONLY
d025 Counter Status READ ONLY
d026 Timer Status READ ONLY
d028 Stp. Logic Status READ ONLY
P031 Motor NP Volts P031 DRIVE RATING
P032 Motor NP Hertz P032 "60.0"
P033 Motor OL Current P033 2XDRIVE RATING
P034 Minimum Freq P034 0.0 Hz
P035 Maximum Freq P035 60 Hz.
P036 Start Source P036 "0" KEYPAD
P037 Stop Mode P037 "0" RAMP, C.F.
P038 Speed Reference P038 "0" DRIVE POT
P039 Accel Time 1 P039 10.0 SEC.
P040 Decel Time 1 P040 10.0 SEC.
P041 Reset To Defalts P041 IDLE State
A051 Digital In1 Sel A051 PRESET FREQ
A052 Digital In2 Sel A052 PRESET FREQ
A053 Digital In3 Sel A053 LOCAL
A054 Digital In4 Sel A054 JOG FORWARD
A055 Relay Out Sel A055 READY/FAULT
A056 Relay Out Level A056 "0.0"
A058 Opto Out 1 Sel A058 MOTOR RUNNING
A059 Opto Out 1 Level A059 "0.0"
A061 Opto Out 2 Sel A061 AT FREQUENCY
A062 Opto Out 2 Level A062 "0.0"
A064 Opto Out Logic A064 "0"
A065 Analog Out Sel A065 "0"
A066 Analog Out High A066 "100%"
A067 Accel Time 2 A067 20.0 SEC
A068 Decel Time 2 A068 20.0 SEC
A069 Internal Freq A069 60.0 Hz.
A070 Preset Freq 0 A070 0.0 Hz.
A071 Preset Freq 1 A071 5.0 Hz.
A072 Preset Freq 2 A072 10.0 Hz.
A073 Preset Freq 3 A073 20.0 Hz.
A074 Preset Freq 4 A074 30.0 Hz
A075 Preset Freq 5 A075 40.0 Hz
A076 Preset Freq 6 A076 50.0 Hz
A077 Preset Freq 7 A077 60.0 Hz.
A078 Jog Frequency A078 10.0 Hz.
A079 Jog Accel/Decel A079 10.0 Sec.
A080 DC Brake Time A080 0.0 Sec.
A081 DC Brake Level A081 Drive Rated x 0.05
A082 DB Resistor Sel A082 "0" Disabled
A083 S Curve % A083 "0" Disabled
A084 Boost Select A084 "8"5%;5 HP"7"2.5
A085 Start Boost "2.5%"
A086 Break Voltage "25%"
A087 Break Frequency 15 Hz.
A088 Maximum Voltage A088 Drive Rating
A089 Current Limit A089 Drive Rating x 1.5
A090 Motor OL Select A090 "0" no derate
A091 PWM Frequency A091 4.0 kHz.
A092 Auto Rstrt Tries A092 "0" Disabled
A093 Auto Rstrt Delay A093 1.0 Sec.
A094 Start At PowerUp A094 "0" Disabled
A095 Reverse Disable A095 "0" Reverse Enabled
A096 Flying Start En A096 "0" Disabled
A097 Compensation A097 "1" Electrical
A098 SW Current Trip A098 0.0 Disabled
A099 Process Factor A099 "30.0"
A100 Fault Clear A100 "0" Ready/Idle
A101 Program Lock A101 "0" Unlocked
A102 Testpoint Sel A102 "400"
A103 Comm Data Rate A103 "3" 9600
A104 Comm Node Addr A104 "100"
A105 Comm Loss Action A105 "0" Fault
A106 Comm Loss Time A106 5.0 Sec.
A107 Comm Format A107 "0" RTU 8-N-1
A108 Language "!" ENGLISH
A110 Anlg In 0-10V Lo A110 "0%"
A111 Anlg In 0-10V Hi A111 "100%"
A112 Anlg In 4-20mA Lo A112 "0.0%"
A113 Anlg In 4-20mA Hi A113 "100%"
A114 Slip Hertz @ FLA A114 2 Hz.
A118 Current Limit 2 DR.RATED x 1.5
A119 Skip Frequency 0 Hz.
A120 Skip Freq. Band 0 Hz.
A121 Stall Fault Time "0" 60 Sec.
A122 Analog In Loss "0" DISABLED
A123 10V Bipolar Enbl. "0" Uni-Polar
A124 Var. PWM Disable "0" Enabled
A125 Torque Perf. Mode V/Hz
A126 Motor NP FLA DRIVE RATED
A127 Autotune "0" Ready/Idle
A128 IR Voltage Drop Dr. Rating Based
A129 Flux Current Ref. Dr. Rating Based
A130 PID Trim High "60.0"
A131 PID Trim Lo "0.1"
A132 PID Ref Select "0" Disabled
A133 PID Feedback Sel "0" 0-10v Input
A134 PID Prop Gain "0.01"
A135 PID Integ Time 0.1 Sec
A136 PID Diff Rate 0.0% 1/Sec
A137 PID Setpoint "0.0"
A138 PID Deadband "0.0"
A139 PID Preload 0.0 Hz.
A140 Stp Logic 0 00F1
A141 Stp Logic 1 00F1
A142 Stp Logic 2 00F1
A143 Stp Logic 3 00F1
A144 Stp Logic 4 00F1
A145 Stp Logic 5 00F1
A146 Stp Logic 6 00F1
A147 Stp Logic 7 00F1
A150 Stp Time 0 30 Sec
A151 Stp Time 1 30 Sec
A152 Stp Time 2 30 Sec
A153 Stp Time 3 30 Sec
A154 Stp Time 4 30 Sec
A155 Stp Time 5 30 Sec
A156 Stp Time 6 30 Sec
A157 Stp Time 7 30 Sec