Exam : Red Hat RH302

Title : Red Hat Certified Engineer

on Redhat Enterprise Linux
5 (Labs)

Version : Demo
1. Change the root Password to redtophat

Answer:

Answer and Explanation:

1.Boot the system in Single user mode

2:Use the passwd command

2. Dig Server1.example.com, Resolve to successfully through DNS Where DNS server is 172.24.254.254

Answer:

Answer and Explanation: #vi /etc/resolv.conf nameserver 172.24.254.254

# dig server1.example.com

#host server1.example.com DNS is the Domain Name System, which maintains a database that can help

your computer translate domain names such as www.redhat.com to IP addresses such as

216.148.218.197. As no individual DNS server is large enough to keep a database for the entire Internet,

they can refer requests to other DNS servers. DNS is based on the named daemon, which is built on the

BIND (Berkeley Internet Name Domain) package developed through the Internet Software Consortium

Users wants to access by name so DNS will interpret the name into ip address. You need to specify the

Address if DNS server in each and every client machine. In Redhat Enterprise Linux, you need to specify

the DNS server into /etc/resolv.conf file. After Specifying the DNS server address, you can verify using host,

dig and nslookup commands.

3. Create the partition having 100MB size and mount it on /mnt/neo

Answer:

Answer and Explanation:

1.Use fdisk /dev/hda-> To create new partition.

2.Type n-> For New partitions

3.It will ask for Logical or Primary Partitions. Press l for logical.

4:It will ask for the Starting Cylinder: Use the Default by pressing Enter Key.

5.Type the Size: +100M-> You can Specify either Last cylinder of Size here.

6.Press P to verify the partitions lists and remember the partitions name.
7.Press w to write on partitions table.

8.Either Reboot or use partprobe command.

9.Use mkfs -t ext3 /dev/hda? Where ? is your partition number

10.Or

11.mke2fs -j /dev/hda? To create ext3 filesystem.

12.mkdir /mnt/neo

13.vi /etc/fstab

14.Write:

15./dev/hda? /mnt/neo ext3 defaults 1 2

16.Verify by mounting on current Sessions also:

17.mount /dev/hda? /mnt/neo

4. Your System is going use as a router for 172.24.0.0/16 and 172.25.0.0/16. Enable the IP Forwarding.

Answer:

Answer and Explanation:

1.echo "1" >/proc/sys/net/ipv4/ip_forward

2.vi /etc/sysctl.conf net.ipv4.ip_forward=1 /proc is the virtual filesystem, containing the information about

the running kernel. To change the parameter of running kernel you should modify on /proc. From Next

reboot the system, kernel will take the value from /etc/sysctl.conf.

5. Some users home directory is shared from your system. Using showmount -e localhost command, the

shared directory is not shown. Make access the shared users home directory.

Answer:

Answer and Explanation:

1. Verify the File whether Shared or not ? : cat /etc/exports

2.Start the nfs service: service nfs start

3.Start the portmap service: service portmap start

4.Make automatically start the nfs service on next reboot: chkconfig nfs on

5.Make automatically start the portmap service on next reboot: chkconfig portmap on

6:Verify either sharing or not: showmount -e localhost

7.Check that default firewall is running on system ? if running flush the iptables using iptables -F and stop

the iptables service.

6. neo user tried by: dd if=/dev/zero of=/home/neo/somefile bs=1024 count=70 files created successfully.

Again neo tried to create file having 70K using following command: dd if=/dev/zero of=/home/neo/somefile

bs=1024 count=70 But he is unable to create the file. Make the user can create the file less then 70K.

Answer:

Answer and Explanation:

Very Tricky question from redhat. Actually question is giving scenario to you to implement quota to neo user.

You should apply the quota to neo user on /home that neo user shouldn't occupied space more than 70K.

1.vi /etc/fstab LABEL=/home /home ext3 defaults,usrquota 0 0 To enable the quota on filesystem you

should mount the filesystem with usrquota for user quota and grpquota for group quota.

2.touch /home/aquota.user ->Creating blank quota database file.

3.mount -o remount /home-> Remounting the /home with updated mount options. You can verify that /home

is mounted with usrquota options or not using mount command.

4.quotacheck -u /home ->Initialization the quota on /home

5.edquota -u neo /home-> Quota Policy editor

See the snapshot

Disk quotas for user neo (uid 500):

Filesystem blocks soft hard inodes soft hard

/dev/mapper/vo-myvol 2 30 70 1 0 0

Can you set the hard limit 70 and soft limit as you think like 30.

Verify using the repquota /home command.

7. One Logical Volume is created named as myvol under vo volume group and is mounted. The Initial Size

of that Logical Volume is 124MB. Make successfully that the size of Logical Volume 245MB without losing

any data. The size of logical volume 240MB to 255MB will be acceptable.

Answer:

Answer and Explanation:

1.First check the size of Logical Volume: lvdisplay /dev/vo/myvol

2.Increase the Size of Logical Volume: lvextend -L+121M /dev/vo/myvol

3.Make Available the size on online: resize2fs /dev/vo/myvol

4.Verify the Size of Logical Volume: lvdisplay /dev/vo/myvol

5.Verify that the size comes in online or not: df -h We can extend the size of logical Volume using the

lvextend command. As well as to decrease the size of Logical Volume, use the lvresize command. In LVM

v2 we can extend the size of Logical Volume without unmount as well as we can bring the actual size of

Logical Volume on online using ext2online command.

8. Quota is implemented on /data but not working properly. Find out the Problem and implement the quota

to user1 to have a soft limit 60 inodes (files) and hard limit of 70 inodes (files).

Answer:

Answer and Explanation: Quotas are used to limit a user's or a group of users' ability to consume disk

space. This prevents a small group of users from monopolizing disk capacity and potentially interfering with

other users or the entire system. Disk quotas are commonly used by ISPs, by Web hosting companies, on

FTP sites, and on corporate file servers to ensure continued availability of their systems. Without quotas,

one or more users can upload files on an FTP server to the point of filling a filesystem. Once the affected

partition is full, other users are effectively denied upload access to the disk. This is also a reason to mount

different filesystem directories on different partitions. For example, if you only had partitions for your root (/)

directory and swap space, someone uploading to your computer could fill up all of the space in your root

directory (/). Without at least a little free space in the root directory (/), your system could become unstable

or even crash. You have two ways to set quotas for users. You can limit users by inodes or by kilobytesized

disk blocks. Every Linux file requires an inode. Therefore, you can limit users by the number of files or by

absolute space. You can set up different quotas for different filesystems. For example, you can set different

quotas for users on the /home and /tmp directories if they are mounted on their own partitions. Limits on disk

blocks restrict the amount of disk space available to a user on your system. Older versions of Red Hat Linux

included LinuxConf, which included a graphical tool to configure quotas. As of this writing, Red Hat no

longer has a graphical quota configuration tool. Today, you can configure quotas on RHEL only through the

command line interface.

1.vi /etc/fstab

/dev/hda11 /data ext3 defaults,usrquota 1 2

2.Either Reboot the System or remount the partition.

Mount -o remount /dev/hda11 /data

3.touch /data/aquota.user

4.quotacheck -ufm /data

5.quotaon -u /data

6.edquota -u user1 /data

and Specified the Soft limit and hard limit on opened file.

To verify either quota is working or not:

Soft limit specify the limit to generate warnings to users and hard limit can't cross by the

user. Use the quota command or repquota command to monitor the quota information.

9. One Logical Volume named lv1 is created under vg0. The Initial Size of that Logical Volume is 100MB.

Now you required the size 500MB. Make successfully the size of that Logical Volume 500M without losing

any data. As well as size should be increased online.

Answer:

Answer and Explanation:

The LVM system organizes hard disks into Logical Volume (LV) groups. Essentially, physical hard disk

partitions (or possibly RAID arrays) are set up in a bunch of equalRH302 sized chunks known as Physical

Extents (PE). As there are several other concepts associated with the LVM system, let's start with some

basic definitions: Physical Volume (PV) is the standard partition that you add to the LVM mix. Normally,

a physical volume is a standard primary or logical partition. It can also be a RAID array. Physical Extent (PE)

is a chunk of disk space. Every PV is divided into a number of equal sized PEs. Every PE in a LV group is

the same size. Different LV groups can have different sized PEs. Logical Extent (LE) is also a chunk of disk

space. Every LE is mapped to a specific PE. Logical Volume (LV) is composed of a group of LEs. You can

mount a filesystem such as /home and /var on an LV. Volume Group (VG) is composed of a group of LVs. It

is the organizational group for LVM. Most of the commands that you'll use apply to a specific VG.

1.Verify the size of Logical Volume: lvdisplay /dev/vg0/lv1

2.Verify the Size on mounted directory: df -h or df -h mounted directory name

3.Use : lvextend -L+400M /dev/vg0/lv1

4.resize2fs /dev/vg0/lv1 to bring extended size online.

5.Again Verify using lvdisplay and df -h command.

10. Create one partitions having size 100MB and mount it on /data.

Answer:

Answer and Explanation:

1. Use fdisk /dev/hda ->To create new partition.

2. Type n-> For New partitions

3. It will ask for Logical or Primary Partitions. Press l for logical.

4. It will ask for the Starting Cylinder: Use the Default by pressing Enter Key.

5. Type the Size: +100M ->You can Specify either Last cylinder of Size here.

6. Press P to verify the partitions lists and remember the partitions name.

7. Press w to write on partitions table.

8. Either Reboot or use partprobe command.

9. Use mkfs -t ext3 /dev/hda?

Or

mke2fs -j /dev/hda? To create ext3 filesystem.

10. vi /etc/fstab

Write:

/dev/hda? /data ext3 defaults 1 2

11: Verify by mounting on current Sessions also:

mount /dev/hda? /data

11. You are new System Administrator and from now you are going to handle the system and your main

task is Network monitoring, Backup and Restore. But you don't know the root password. Change the root

password to redhat and login in default Runlevel.

Answer:

Answer and Explanation:

When you Boot the System, it starts on default Runlevel specified in /etc/inittab:

Id:?:initdefault:

When System Successfully boot, it will ask for username and password. But you don't
know the root's password. To change the root password you need to boot the system into

single user mode. You can pass the kernel arguments from the boot loader.

1. Restart the System.

2. You will get the boot loader GRUB screen.

3. Press a and type 1 or s for single mode ro root=LABEL=/ rhgb queit s

4. System will boot on Single User mode.

5.Use passwd command to change.

6.Press ctrl+d

12. There are more then 400 Computers in your Office. You are appointed as a System Administrator. But

you don't have Router. So, you are going to use your One Linux Server as a Router. How will you enable IP

packets forward?

Answer:

Answer and Explanation:

1./proc is the virtual filesystem, we use /proc to modify the kernel parameters at running time. # echo "1"

>/proc/sys/net/ipv4/ip_forward

2. /etc/sysctl.conf when System Reboot on next time, /etc/rc.d/rc.sysinit scripts reads the file

/etc/sysctl.conf.-> To enable the IP forwarding on next reboot also you need to set the parameter.

net.ipv4.ip_forward=1 Here 0 means disable, 1 means enable.

13. You Completely Install the Redhat Enterprise Linux 5 on your System. While start the system, it's giving

error to load X window System. How will you fix that problem and make boot successfully run X Window

System.

Answer:

Answer and Explanation:

Think while Problems occurred on booting System on Runlevel 5 (X Window).

1./tmp is full or not

2.Quota is already reached

3.Video card or resolution or monitor is misconfigured.

4.xfs service is running or not. Do These:

1.df -h /tmp /tmp is full remove the unnecessary file

2.quota username if quota is already reached remove unnecessary file from home directory.

3.Boot the System in runlevel 3. you can pass the Kernel Argument from boot loader.

4.Use command: system-config-display It will display a dialog to configure the monitor, Video card,

resolution etc.

5.Set the Default Runlevel 5 in /etc/inittab id:5:initdefault:

6.Reboot the System you will get the GUI login Screen.

14. There are two different networks, 192.168.0.0/24 and 192.168.1.0/24. Your System is in 192.168.0.0/24

Network. One RHEL 5 Installed System is going to use as a Router. All required configuration is already

done on Linux Server. Where 192.168.0.254 and 192.168.1.254 IP Address are assigned on that Server.

How will make successfully ping to 192.168.1.0/24 Network's Host?

Answer:

Answer and Explanation:

1. vi /etc/sysconfig/network

GATEWAY=192.168.0.254 OR vi /etc/sysconf/network-scripts/ifcfg-eth0

DEVICE=eth0

BOOTPROTO=static

ONBOOT=yes

IPADDR=192.168.0.?

NETMASK=255.255.255.0

GATEWAY=192.168.0.254

2. service network restart

Explanation: Gateway defines the way to exit the packets. According to question System working as a

router for two networks have IP Address 192.168.0.254 and 192.168.1.254. To get the hosts on

192.168.1.0/24 should go through 192.168.0.254.

15. Make a swap partition having 100MB. Make Automatically Usable at System Boot Time.

Answer:

Answer and Explanation:

1.Use fdisk /dev/hda ->To create new partition.

2.Type n-> For New partition

3.It will ask for Logical or Primary Partitions. Press l for logical.

4.It will ask for the Starting Cylinder: Use the Default by pressing Enter Key.

5.Type the Size: +100M ->You can Specify either Last cylinder of Size here.

6.Press P to verify the partitions lists and remember the partitions name. Default System ID is 83 that

means Linux Native.

7.Type t to change the System ID of partition.

8.Type Partition Number

9.Type 82 that means Linux Swap.

10.Press w to write on partitions table.

11.Either Reboot or use partprobe command.

12.mkswap /dev/hda? ->To create Swap File system on partition.

13.swapon /dev/hda? ->To enable the Swap space from partition.

14.free -m ->Verify Either Swap is enabled or not.

15.vi /etc/fstab/dev/hda? swap swap defaults 0 0

16:Reboot the System and verify that swap is automatically enabled or not.

16. You are a System administrator. Using Log files very easy to monitor the system.

Now there are 50 servers running as Mail, Web, Proxy, DNS services etc. You want to centralize the logs

from all servers into on LOG Server. How will you configure

the LOG Server to accept logs from remote host ?

Answer:

Answer and Explanation:

By Default system accept the logs only generated from local host. To accept the Log

from other host configure:

1.vi /etc/sysconfig/syslog SYSLOGD_OPTIONS="-m 0 -r" Where -m 0 disables 'MARK' messages. -r

enables logging from remote machines -x disables DNS lookups on messages recieved with -r 2. service

syslog restart
17. You are giving the debug RHCT exam. The examiner told you that the password of root is redhat. When

you tried to login displays the error message and redisplayed the login screen. You changed the root

password, again unable to login as a root.

How will you make Successfully Login as a root.

Answer:

Answer and Explanation:

When root unable to login into the system think:

1.Is password correct? 2. Is account expired? 3. Is terminal Blocked? Do these Steps:

Boot the System on Single user mode.

Change the password

Check the account expire date by using chage -l root command. If account is expired, set net expire date:

chage -E "NEVER" root 1.Check the file /etc/securetty Which file blocked to root login from certain terminal.

2.If terminal is deleted or commented write new or uncomment.

3.Reboot the system and login as a root.

18. You are giving RHCT Exam and in your Exam paper there is a question written, make successfully ping

to 192.168.0.254.

Answer:

Answer and Explanation:

In Network problem thinks to check:

1. IP Configuration: use ifconfig command either IP is assigned to interface or not?

2. Default Gateway is set or not?

3. Hostname is set or not?

4. Routing problem is there?

5. Device Driver Module is loaded or not?

6. Device is activated or not?

Check In this way:

1. use ifconfig command and identify which IP is assigned or not.

2. cat /etc/sysconfig/network What, What is written here. Actually here are these

parameters.
NETWORKING=yes or no

GATEWAY=x.x.x.x

HOSTNAME=?

NISDOMAIN=?

- Correct the file

3. Use vi /etc/sysconfig/network-scirpts/ifcfg-eth0 and check the proper options DEVICE=eth0

ONBOOT=yes BOOTPROTO=static IPADDR=x.x.x.x NETMAKS=x.x.x.x

GATEWAY=x.x.x.x

4. Use service network restart or start command

19. Set the Hostname station?.example.com where ? is your Host IP Address.

Answer:

Answer and Explanation:

1. hostname station?.example.com This will set the host name only for current session. To set hostname

permanently.

2.vi /etc/sysconfig/network HOSTNAME=station?.example.com

3.service network restart

20. The System you are using is for NFS (Network File Services). Some important data are shared from

your system. Make automatically start the nfs and portmap services at boot time.

Answer:

Answer and Explanation: We can control the services for current session and for next boot time also. For

current Session, we use service servicename start or restart or stop or status. For automatically on next

reboot time:

1.chkconfig servicename on or off eg: chkconfig nfs on chkconfig portmap on or ntsysv Select the nfs and

portmap services.

2.Reboot the system and identify whether services are running or not.

21. There is one partition /dev/hda14 mounted on /data. The owner of /data is root user and root group. And

Permission is full to owner user, read and execute to group member and no permission to others. Now you
should give the full permission to user user1 without changing pervious permission.

Answer:

Answer and Explanation: We know that every files/directories are owned by certain user and group. And

Permissions are defines to owner user, owner group and other. -rwxr-x----> Full permission to owner user,

read and write to owner group and no permission to others. According to question: We should give the full

permission to user user1 without changing the previous permission. ACL (Access Control List), in ext3 file

system we can give permission to certain user and certain group without changing previous permission. But

that partition should mount using acl option. Follow the steps

1.vi /etc/fstab /dev/hda14 /data ext3 defaults,acl 0 1

2.Either Reboot or use: mount -o remount /data

3.setfacl -m u:user1:rwx /data

4.Verify using: getfacl /data

22. There are two different networks 192.168.0.0/24 and 192.168.1.0/24. Where 192.168.0.254 and

192.168.1.254 IP Address are assigned on Server. Verify your network settings by pinging 192.168.1.0/24

Network's Host.

Answer:

Answer and Explanation:

1.vi /etc/sysconfing/network

NETWORKING=yes

HOSTNAME=station?.example.com

GATEWAY=192.168.0.254

2. service network restart Or

1. vi /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 ONBOOT=yes BOOTPROTO=static

IPADDR=X.X.X.X

NETMASK=X.X.X.X

GATEWAY=192.168.0.254

2. ifdown eth0

3. ifup eth0
23. Your system is giving error while booting on Runlevel 5 . Make successfully boot your system in runlevel

5.

Answer:

Answer and Explanation:

While you load the X Window System, you will get the problem. To troubleshoot follow the following steps:

1.Check the /tmp is full

2.Check your quota, hard limit is already crossed

3.Check xfs service is running

4.Boot the system on runlevel 3 and execute the system-config-display command

5.Edit the /etc/inittab to set default runlevel 5. id:5:initdefault:

24. Your System is configured in 192.168.0.0/24 Network and your nameserver is 192.168.0.254. Make

successfully resolve to server1.example.com.

Answer:

Answer and Explanation:

Very Easy question, nameserver is specified in question,

1. vi /etc/resolv.conf nameserver 192.168.0.254

2. host server1.example.com

Explanation: DNS is the Domain Name System, which maintains a database that can help your computer

translate domain names such as www.redhat.com to IP addresses such as 216.148.218.197. As no

individual DNS server is large enough to keep a database for the entire Internet, they can refer requests to

other DNS servers. DNS is based on the named daemon, which is built on the BIND (Berkeley Internet

Name Domain) package developed through the Internet Software Consortium Users wants to access by

name so DNS will interpret the name into ip address. You need to specify the Address if DNS server in each

and every client machine. In Redhat Enterprise Linux, you need to specify the DNS server into

/etc/resolv.conf file. After Specifying the DNS server address, you can verify using host, dig and nslookup

commands. #host server1.example.com

25. One Package named zsh is dump on ftp://server1.example.com under /pub/updates directory and your

FTP server is 192.168.0.254. Install the package zsh.

Answer:

Answer and Explanation:

1. rpm -ivh ftp://server1/example.com/pub/updates/zsh-* or

1. Login to ftp server : ftp ftp://server1.example.com using anonymous user.

2. Change the directory: cd pub and cd updates

3. Download the package: mget zsh-*

4. Quit from the ftp prompt : bye

5. Install the package

6. rpm -ivh zsh-*

7. Verify either package is installed or not : rpm -q zsh

26. Add a new logical partition having size 100MB and create the /data which will be the mount point for the

new partition.

Answer:

Answer and Explanation:

1.Use fdisk /dev/hda ->To create new partition.

2. Type n-> For New partitions

3. It will ask for Logical or Primary Partitions. Press l for logical.

4. It will ask for the Starting Cylinder: Use the Default by pressing Enter Key.

5. Type the Size: +100M ->You can Specify either Last cylinder of Size here.

6. Press P to verify the partitions lists and remember the partitions name.

7. Press w to write on partitions table.

8. Either Reboot or use partprobe command.

9. Use mkfs -t ext3 /dev/hda?

10. Or

11. mke2fs -j /dev/hda? To create ext3 filesystem.

12. vi /etc/fstab

13. Write:

14. /dev/hda? /data ext3 defaults 0 0

11. Verify by mounting on current Sessions also:

15. mount /dev/hda? /data

27. There is a server having 172.24.254.254 and 172.25.254.254. Your System lies on 172.24.0.0/16. Make

successfully ping to 172.25.254.254 by Assigning following IP: 172.24.0.x Where x is your station number.

Answer:

Answer and Explanation:

1.vi /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=static ONBOOT=yes

IPADDR=x.x.x.x

NETMASK=x.x.x.x

2. Enter the IP Address as given station number by your examiner: example: 172.24.0.1

3. Enter Subnet Mask

4. Enter Default Gateway and primary name server

5. press on ok

6. ifdown eth0

7. ifup eth0

8. verify using ifconfig In the lab server is playing the role of router, IP forwarding is enabled. Just set the

Correct IP and gateway, you can ping to 172.25.254.254.

28. Successfully resolv to server1.example.com where your DNS server is 172.24.254.254

Answer:

Answer and Explanation:

1.vi /etc/resolv.conf nameserver 172.24.254.254 2. host server1.example.com

Explanation: DNS is the Domain Name System, which maintains a database that can help your computer

translate domain names such as www.redhat.com to IP addresses such as 216.148.218.197. As no

individual DNS server is large enough to keep a database for the entire Internet, they can refer requests to

other DNS servers. DNS is based on the named daemon, which is built on the BIND (Berkeley Internet

Name Domain) package developed through the Internet Software Consortium Users wants to access by

name so DNS will interpret the name into ip address. You need to specify the Address if DNS server in each

and every client machine. In Redhat Enterprise Linux, you need to specify the DNS server into

/etc/resolv.conf file. After Specifying the DNS server address, you can verify using host, dig and nslookup
commands. #host server1.example.com

29. Make Successfully Resolve to server1.example.com where DNS Server is 192.168.0.254.

Answer:

1. vi /etc/resolv.conf Write : nameserver 192.168.0.254

Explanation: DNS is the Domain Name System, which maintains a database that can help your computer

translate domain names such as www.redhat.com to IP addresses such as 216.148.218.197. As no

individual DNS server is large enough to keep a database for the entire Internet, they can refer requests to

other DNS servers. DNS is based on the named daemon, which is built on the BIND (Berkeley Internet

Name Domain) package developed through the Internet Software Consortium Users wants to access by

name so DNS will interpret the name into ip address. You need to specify the Address if DNS server in each

and every client machine. In Redhat Enterprise Linux, you need to specify the DNS server into

/etc/resolv.conf file. After Specifying the DNS server address, you can verify using host, dig and nslookup

commands. #host server1.example.com

30. One Logical Volume is created named as myvol under vo volume group and is mounted. The Initial Size

of that Logical Volume is 400MB. Make successfully that the size of Logical Volume 200MB without losing

any data. The size of logical volume 200MB to 210MB will be acceptable.

Answer:

Answer and Explanation: 1.First check the size of Logical Volume: lvdisplay /dev/vo/myvol

2.Make sure that the filesystem is in a consistent state before reducing: # fsck -f /dev/vo/myvol

3.Now reduce the filesystem by 200MB. # resize2fs /dev/vo/myvol 200M

4.It is now possible to reduce the logical volume. #lvreduce /dev/vo/myvol -L 200M

4.Verify the Size of Logical Volume: lvdisplay /dev/vo/myvol

5.Verify that the size comes in online or not: df -h