HI-8573, HI-8574, HI-8575

September 2006 Quad CMOS Op Amp / Comparator

DESCRIPTION FEATURES
The HI-8573, HI-8574 and HI-8575 devices are designed
using low power CMOS technology. The operating current
! Single or dual power supply. +3 to 15Vdc
or ±1.5 to ±7.5Vdc
! Wide input voltage range
is externally programmable with a resistor to give the
optimum tradeoff between power dissipation and slew

! Common mode range 0 to VCC-2V single

rate. The operational amplifiers are internally
compensated.

All three versions offer a high degree of versatility and are

supply
well suited for both line-powered and battery-powered
systems. Features include a typical offset voltage of ! Adjustable current / slew rate
±5 mV, high input impedance and low current drain.
Either single or dual power supply operation may be ! Typical offset ±5 mV
used up to 15V DC. The comparators are CMOS and
TTL compatible. The three devices are direct ! Internally compensated op amps
replacements for the Motorola/ON-Semiconductor
MC14573, MC14574 and MC14575 respectively. ! High input impedance
! CMOS and TTL compatible comparators
APPLICATIONS
! Direct replacements for Motorola / On
Semiconductor MC14573, MC14574 and
MC14575
! Oscillators
! Function generators
PIN CONFIGURATION
! Active filters
! Logic level converters
! Voltage reference Output A 1 16 Output D

! Zero crossing detectors

Input A - 2 15 Input D -

Input A + 3 14 Input D +

! Instrumentation VCC 4 13 VEE

Input B + 5 12 Input C +

Input B - 6 11 Input C -

Output B 7 10 Output C

ISET A, B 8 9 ISET C, D

16 Pin Plastic DIP & SOIC packages

HOLT INTEGRATED CIRCUITS

(DS8573 Rev. B) www.holtic.com 09/06
 HI-8573, HI-8574, HI-8575

PIN DESCRIPTIONS

PIN SYMBOL FUNCTION DESCRIPTION

HI-8573 HI-8574 HI-8575
1 Output A Analog output Amplifier A Comparator A Amplifier A
2 Input A- Analog input Amplifier A Comparator A Amplifier A
3 Input A+ Analog input Amplifier A Comparator A Amplifier A
4 VCC Power Positive supply voltage
5 Input B+ Analog input Amplifier B Comparator B Amplifier B
6 Input B- Analog input Amplifier B Comparator B Amplifier B
7 Output B Analog output Amplifier B Comparator B Amplifier B
8 ISET A, B Analog input Bias control for A and B
9 ISET C, D Analog input Bias control for C and D
10 Output C Analog output Amplifier C Comparator C Comparator C
11 Input C- Analog input Amplifier C Comparator C Comparator C
12 Input C+ Analog input Amplifier C Comparator C Comparator C
13 VEE Power Negative supply voltage
14 Input D+ Analog input Amplifier D Comparator D Comparator D
15 Input D- Analog input Amplifier D Comparator D Comparator D
16 Output D Analog output Amplifier D Comparator D Comparator D

PROGRAMMING CURRENT
The programming current ISET is fixed by an external re- It should be noted that increasing ISET for comparators
sistor RSET connected between VEE and either one or will decrease propagation delay for that comparator.
both of the ISET pins (8 and 9). When two external pro-
gramming resistors are used, the set currents for each op For operational amplifiers, the maximum obtainable out-
amp pair or comparator are given by: put voltage (VOH) for a given load resistor connected to
VEE is given by:
ISET (mA) @ (VCC-VEE-1.0)/RSET (MW)
-3
VOH = (4 x 10 ISET)RL - 0.05V
Pins 8 and 9 may be tied together for use with a single pro-
-3
gramming resistor. The set currents for each op amp or if (4 x 10 ISET) RL < VCC
comparator pair are then given by:
where, RL is in KW, ISET is in mA
ISET (mA) @ (VCC-VEE-1.0)/2 RSET (MW)
Typical op amp slew rates are given by:
If a pair of op amps or comparators are not used, the ISET
pin for that pair may be tied to VCC for minimum power SR @ 0.05 ISET (V/ms).
consumption.
where, ISET is in mA

HOLT INTEGRATED CIRCUITS

2
 HI-8573, HI-8574, HI-8575

ABSOLUTE MAXIMUM RATINGS RECOMMENDED OPERATING CONDITIONS

Supply voltage (VCC) -0.5 V to +18 V Supply Voltage
Input voltage. All inputs -0.5 V to VCC+0.5 V VCC-VEE .......................... +3.0 to +15 V
DC input current, per pin ±10 mA Temperature Range
Programming current range 2.0 mA Industrial Screening.........-40°C to +85°C
Storage temperature range -60 to +150 °C
NOTE: Stresses above absolute maximum
Solder Temperature (Leads) 275°C for 10 sec ratings or outside recommended operating
Solder Temperature (Body) 220°C conditions may cause permanent damage to the
device. These are stress ratings only. Operation
at the limits is not recommended.

ELECTRICAL CHARACTERISTICS - OPERATIONAL AMPLIFIER

VEE = 0 V, TA = 25°C (unless otherwise specified).
PARAMETER SYMBOL VCC MIN TYP MAX UNITS

Input common mode voltage range (ISET = 200 mA) 5 0 3

VICR 10 0 8 Vdc
15 0 13

Output voltage range (ISET = 50 mA) 5 1.05 4

(RL = 100 KW connected to VEE) VOR 10 1.05 9 Vdc
15 1.05 14

Input offset voltage VIO 10 ±5 ±25 mVdc

Average temperature coefficient of VIO DVIO/DT 20 mV/°C

Input bias current IIB 10 1 nA

Input offset current IIO 10 200 pA

Open loop voltage gain (ISET = 50 mA) AVOL 10 90 dB

Power supply rejection ratio PSRR 10 70 dB

Common mode rejection ratio CMRR 10 80 dB

Channel separation 10 -100 dB

Slew rate SR 10 2.5 V/ms

Phase margin FM 10 45 Degrees

Supply current, per pair (RSET = 1 MW) 5 50

ICC 10 100 mA
15 150

Supply current, per pair (RSET = 100 KW) 5 0.5

ICC 10 1.2 mA
15 1.8

Gain x Bandwidth product GBP 10 1.4 MHz

HOLT INTEGRATED CIRCUITS

3
 HI-8573, HI-8574, HI-8575

ELECTRICAL CHARACTERISTICS - COMPARATOR

VEE = 0V, TA = 25°C (unless otherwise specified).
PARAMETER SYMBOL VCC MIN TYP MAX UNITS

Input common mode voltage range (ISET = 200 mA) 5 0 3

VICR 10 0 8 V
15 0 13

Output low voltage "0" level 5 0 0.05

VOL 10 0 0.05 V
15 0 0.05

Output high voltage "1" level 5 4.95 5

VOH 10 9.95 10 V
15 14.95 15

Output source current (VOH = 2.5 V) 5 -0.24 -0.42

(VOH = 4.6 V) 5 -0.51 -0.88
IOH mAdc
(VOH = 9.5 V) 10 -1.3 -2.25
(VOH = 13.5 V) 15 -3.4 -8.8

Output sink current (VOL = 0.4 V) 5 1.25 2.25

(VOL = 0.5 V) IOL 10 3.25 5.6 mAdc
(VOL = 1.5 V) 15 8.5 20

Input offset voltage (ISET = 50 mA) VIO 10 ±5 ±25 mVdc

Average temperature coefficient of VIO DVIO/DT 20 mV/°C

Input bias current IIB 10 1 nA

Input offset current IIO 10 200 pA

Open loop voltage gain (ISET = 50 mA) AVOL 10 96 dB

Power supply rejection ratio PSRR 10 70 dB

Common mode rejection ratio CMRR 10 80 dB

Channel separation 10 -100 dB

Output rise and fall time (CL = 50 pF) tTLH

10 100 ns
tTHL

Propagation delay time, (ISET = 50 mA, CL = 50 pF)

tD 10 1000 ns
5 mV overdrive

Supply current, per pair (RSET = 1 MW) 5 50

ICC 10 100 mA
15 150

Supply current, per pair (RSET = 100 KW) 5 0.45

ICC 10 1.0 mA
15 1.5

NOTE: Unused inputs should always be tied to either VCC or VEE

HOLT INTEGRATED CIRCUITS

4
 HI-8573, HI-8574, HI-8575

POWER OPTIONS
VCC VCC

1.5 to 7.5 V

3.0 to 15 V

1.5 to 7.5 V

VEE VEE

Single Supply Split Supply

CIRCUIT DIAGRAMS

VCC VCC

ISET ISET

INPUT (+) INPUT (+)

INPUT (-) INPUT (-) OUTPUT

OUTPUT

VEE VEE

Operational Amplifier Comparator

HOLT INTEGRATED CIRCUITS

5
 HI-8573, HI-8574, HI-8575

ORDERING INFORMATION
HI - 857x xx I x

PART LEAD
NUMBER FINISH
Blank Tin / Lead (Sn / Pb) Solder
F 100% Matte Tin (Pb-free, RoHS compliant)

PART TEMPERATURE FLOW BURN

NUMBER RANGE IN
I -40°C TO +85°C I NO

PART PACKAGE
NUMBER DESCRIPTION
PD 16 PIN PLASTIC DIP
PS 16 PIN PLASTIC SOIC - NB

PART FUNCTION
NUMBER
8573 QUAD OP AMP
8574 QUAD COMPARATOR
8575 DUAL OP AMP / DUAL COMPARATOR

Legend: NB - Narrow Body

HOLT INTEGRATED CIRCUITS

6
 PACKAGE DIMENSIONS
inches (millimeters)

16-PIN PLASTIC DIP

Package Type: 16P

.777 ±.033
(19.736 ±.838)

.250 ±.010
(6.350 ± .254)

.305 ±.015
(7.747 ±.381)

.160 ±.025 .135 ±.015

(4.064 ±.635) 7° TYP. (3.429 ±.381)

.130 ±.020 0° ~ 15°

(3.302 ±.508)
.019 ±.004
.100 ±.010
(.483 ±.102)
(3.540 ±.254) .340 ±.040
.055 ±.010 (8.636± 1.016)
(1.397± .254)

16-PIN PLASTIC SMALL OUTLINE - NB

(Narrow Body) Package Type: 16HN

.00865 ± .00115
.3898 ± .0039 (.220 ± .029)
(9.901 ± .099)

.236 ±.008
.008 .1535 ± .0035
Top View
(6.00 ±.20)
.20) (3.899 ± .089)

Detail A
.0165 ± .0035
(.419 ± ..089) .061 ± .007
(1.549 ± .178)

0° to 8° .0069 ± .0029
(.175 ± .074)
.050 ±.010
.010 .033 ± .017 Detail A
(1.270 ±.254)
.254) (.838 ± .432)

HOLT INTEGRATED CIRCUITS

7