Scribd
Upload
43 views10 pages

Kasus 1 1. Gambar Scenario

The document describes the configuration of HDLC and PPP on multiple routers to connect several networks. IP addresses, interfaces, and routing protocols are configured on each router to establish connectivity between the networks.

Uploaded by

Arman Chan
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
43 views10 pages

Kasus 1 1. Gambar Scenario

The document describes the configuration of HDLC and PPP on multiple routers to connect several networks. IP addresses, interfaces, and routing protocols are configured on each router to establish connectivity between the networks.

Uploaded by

Arman Chan
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 10

Kasus 1

1. Gambar scenario

KONFIGURASI HDLC DAN PPP

NO NAMA INTERFACE IP ADDRESS SUBNETMASK GATEWAY

1 PC0 192.168.1.1 255.255.255.0 192.168.1.254

2 PC1 192.168.2.1 255.255.255.0 192.168.2.254

3 PC2 192.168.3.1 255.255.255.0 192.168.3.254

4 Router0 Int fa0/0 192.168.1.254 255.255.255.0 -

Int se0/0/0 192.168.4.5 255.255.255.252 -

Int se0/0/1 192.168.4.9 255.255.255.252 -

5 Router1 Int se0/0/0 192.168.4.6 255.255.255.252 -

Int se0/0/1 192.168.4.13 255.255.255.252 -

6 Router2 Int se0/0/0 192.168.4.14 255.255.255.252 -

Int se0/0/0 192.168.4.29 255.255.255.252 -


7 Router3 Int fa0/0 192.168.3.254 255.255.255.0 -

Int se0/0/0 192.168.4.30 255.255.255.252 -

Int se0/0/1 192.168.4.34 255.255.255.252 -

8 Router4 Int se0/0/0 192.168.4.18 255.255.255.252 -

Int se0/0/1 192.168.4.25 255.255.255.252 -

Int se0/1/0 192.168.4.33 255.255.255.252 -

9 Router5 Int fa0/0/0 192.168.4.10 255.255.255.252 -

Int se0/0/1 192.168.4.17 255.255.255.252 -

Int se0/1/0 192.168.4.21 255.255.255.252 -

10 Router6 Int fa0/0 192.168.2.254 255.255.255.0 -

Int se0/0 192.168.4.22 255.255.255.252 -

Int se0/1 192.168.4.26 255.255.255.252 -

KONFIGURASI R0

Router> en

Router#config t

Router(config)#int fa0/0

Router(config-if)#ip addr 192.168.1.254 255.255.255.0

Router(config-if)#int se0/0/0

Router(config-if)#ip addr 192.168.4.5 255.255.255.252

Router(config-if)#encap hdlc

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial2/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on serial2/0, changed state to up

Router(config-if)#int se0/0/1
Router(config-if)#ip addr 192.168.4.9 255.255.255.252

Router(config-if)#encap hdlc

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial3/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface serial3/0, changed state to up

Router(config-if)#ex

Router(config)# ip route 192.168.0.24.255.255.255.252 192.168.0.6

Router (config)#ip route 192.168.4.12 255.255.255.252 192.168.4.6

Router (config)#ip route 192.168.4.28 255.255.255.252 192.168.4.6

Router (config)#ip route 192.168.3.0 255.255.255.255 192.168.4.6

Router (config)#ip route 192.168.4.16 255.255.255.252 192.168.4.10

Router (config)#ip route 192.168.4.20 255.255.255.252 192.168.4.10

Router (config)#ip route 192.168.4.32 255.255.255.252 192.168.4.10

Router (config)#ip route 192.168.4.24 255.255.255.252 192.168.4.10

Router (config)#ip route 192.168.2.0 255.255.255.255 192.168.4.10

Konfigurasi R1

Router> en

Router#config t

Router(config)#int se0/0/0

Router(config-if)#ip addr 192.168.4.6 255.255.255.252

Router(config-if)#encap hdlc

Router(config-if)#clock rate 64000

Router(config-if)#no shut
%LINK-5-CHANGED: Interface serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on serial0/0/0, changed state to up

Router(config-if)#int se0/0/1

Router(config-if)#ip addr 192.168.4.13 255.255.255.252

Router(config-if)#encap ppp

Router(config-if)#ppp authentication chap pap

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial0/0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface serial0/0/1, changed state to up

Router(config-if)#exit

Router(config)#hostname R1

R1(config)#username R2 password cisco

R1(config)#ip route 192.168.4.8 255.255.255.252 192.168.4.5

R1(config)#ip route 192.168.4.16 255.255.255.252 192.168.4.5

R1(config)#ip route 192.168.4.28 255.255.255.252 192.168.4.14

R1(config)#ip route 192.168.4.32 255.255.255.252 192.168.4.14

R1(config)#ip route 192.168.4.24 255.255.255.252 192.168.4.14

R1(config)#ip route 192.168.3.0 255.255.255.255 192.168.4.14

R1(config)#ip route 192.168.2.0 255.255.255.0 192.168.4.14

R1(config)#ip route 192.168.3.0 255.255.255.0 192.168.4.14

Konfigurasi R2

Router> en
Router#config t

Router(config)#int se0/0/0

Router(config-if)#ip addr 192.168.4.14 255.255.255.252

Router(config-if)#encap ppp

Router(config-if)#ppp authentication chap pap

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on serial0/0/0, changed state to up

Router(config-if)#int se0/0/1

Router(config-if)#ip addr 192.168.4.29 255.255.255.252

Router(config-if)#encap ppp

Router(config-if)#ppp authentication chap pap

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial0/0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface serial0/0/1, changed state to up

Router(config-if)#exit

Router(config)#hostname R1

R1(config)#username R2 password cisco

R1(config)#username R3 password cisco

R1(config)#ip route 192.168.4.8 255.255.255.252 192.168.4.5

R1(config)#ip route 192.168.4.16 255.255.255.252 192.168.4.5

R1(config)#ip route 192.168.4.28 255.255.255.252 192.168.4.14

R1(config)#ip route 192.168.4.32 255.255.255.252 192.168.4.14


R1(config)#ip route 192.168.4.24 255.255.255.252 192.168.4.14

R1(config)#ip route 192.168.3.0 255.255.255.255 192.168.4.14

R1(config)#ip route 192.168.2.0 255.255.255.0 192.168.4.14

R1(config)#ip route 192.168.3.0 255.255.255.0 192.168.4.14

Konfigurasi R3

Router> en

Router#config t

Router(config)#int fa0/0

Router(config-if)#ip addr 192.168.3.254 255.255.255.0

Router(config-if)#int se0/0/0

Router(config-if)#ip addr 192.168.4.30 255.255.255.252

Router(config-if)#encap ppp

Router(config-if)#ppp authentication chap pap

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial2/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on serial2/0, changed state to up

Router(config-if)#int se0/0/1

Router(config-if)#ip addr 192.168.4.34 255.255.255.252

Router(config-if)#encap hdlc

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial3/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface serial3/0, changed state to up


Router(config-if)#exit

Router(config)#hostname R3

R1(config)#username R2 password cisco

R3(config)#ip route 192.168.4.8 255.255.255.252 192.168.4.5

R3(config)#ip route 192.168.4.16 255.255.255.252 192.168.4.5

R3(config)#ip route 192.168.4.28 255.255.255.252 192.168.4.14

R3(config)#ip route 192.168.4.32 255.255.255.252 192.168.4.14

R3(config)#ip route 192.168.4.24 255.255.255.252 192.168.4.14

R3(config)#ip route 192.168.3.0 255.255.255.255 192.168.4.14

R3(config)#ip route 192.168.2.0 255.255.255.0 192.168.4.14

R3(config)#ip route 192.168.3.0 255.255.255.0 192.168.4.14

Konfigurasi R4

Router> en

Router#config t

Router(config)#int se0/0/0

Router(config-if)#ip addr 192.168.4.18 255.255.255.252

Router(config-if)#encap ppp

Router(config-if)#ppp authentication chap pap

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on serial0/0/0, changed state to up

Router(config-if)#int se0/0/1

Router(config-if)#ip addr 192.168.4.25 255.255.255.252


Router(config-if)#encap hdlc

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial0/0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface serial0/0/1, changed state to up

Router(config-if)#int se0/1/0

Router(config-if)#ip addr 192.168.4.33 255.255.255.252

Router(config-if)#encap hdlc

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial0/1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface serial0/0/1, changed state to up

Router(config-if)#exit

Router(config)#hostname R4

R1(config)#username R5 password cisco

R4(config)#username R3 password cisco

R4(config)#ip route 192.168.4.8 255.255.255.252 192.168.4.5

R4(config)#ip route 192.168.4.16 255.255.255.252 192.168.4.5

R4(config)#ip route 192.168.4.28 255.255.255.252 192.168.4.14

R4(config)#ip route 192.168.4.32 255.255.255.252 192.168.4.14

R4(config)#ip route 192.168.4.24 255.255.255.252 192.168.4.14

R4(config)#ip route 192.168.3.0 255.255.255.255 192.168.4.14

R4(config)#ip route 192.168.2.0 255.255.255.0 192.168.4.14

R4(config)#ip route 192.168.3.0 255.255.255.0 192.168.4.14


Konfigurasi Router5

Konfigurasi R4

Router> en

Router#config t

Router(config)#int se0/0/0

Router(config-if)#ip addr 192.168.4.10 255.255.255.252

Router(config-if)#encap dhlc

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on serial0/0/0, changed state to up

Router(config-if)#int se0/0/1

Router(config-if)#ip addr 192.168.4.17 255.255.255.252

Router(config-if)#encap hdlc

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial0/0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface serial0/0/1, changed state to up

Router(config-if)#int se0/1/0

Router(config-if)#ip addr 192.168.4.21 255.255.255.252

Router(config-if)#encap hdlc

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface serial0/1/0, changed state to up


%LINEPROTO-5-UPDOWN: Line protocol on Interface serial0/0/1, changed state to up

Router(config-if)#exit

Router(config)#hostname R5

R5(config)#username R4 password cisco

R5(config)#username R3 password cisco

R5config)#ip route 192.168.4.8 255.255.255.252 192.168.4.5

R5(config)#ip route 192.168.4.16 255.255.255.252 192.168.4.5

R5(config)#ip route 192.168.4.28 255.255.255.252 192.168.4.14

R5(config)#ip route 192.168.4.32 255.255.255.252 192.168.4.14

R5(config)#ip route 192.168.4.24 255.255.255.252 192.168.4.14

R5(config)#ip route 192.168.3.0 255.255.255.255 192.168.4.14

R5(config)#ip route 192.168.2.0 255.255.255.0 192.168.4.14

R5(config)#ip route 192.168.3.0 255.255.255.0 192.168.4.14

You might also like