V i s u a l I n d e x

SCREW CLAMP 35 & 32 MM DIN RAIL, FEED THROUGH

SINGLE LEVEL
CTS2.5U-N CTS4U-N CTS6U CTS10U CTS16U CTS25U

5 mm 6 mm 8 mm 10 mm 12 mm 12 mm
PAGE 12 PAGE 12 PAGE 13 PAGE 13 PAGE 13 PAGE 13

SINGLE LEVEL HIGH CURRENT MULTI CONNECTION DOUBLE LEVEL

CTS35U CTS50U CTS95U CMC1-2 CMC2-2 CDL4U

150 Amp 230 Amp 3 conductor 4 conductor 6 mm

15 mm PAGE 14 PAGE 14 PAGE 15 PAGE 15 PAGE 16
PAGE 14

DOUBLE LEVEL TRIPLE LEVEL

CDL4UI.S ODL4U CTL2.5U-H CTL2.5U CTL2.5U-H(L) CTL2.5U(L)

4 conductor offset for sensor/actuator for motor circuits for sensor/actuator for motor circuits
PAGE 16 PAGE 17 PAGE 18 PAGE 18 PAGE 19 PAGE 19
SCREW CLAMP 35 & 32 MM DIN RAIL
DISTRIBUTION BLOCK
CDB4 CDB4(1) CDB6 CDB10 CMDB4 CMDB6

50 Amp 50 Amp 100 Amp 130 Amp 35 Amp 50 Amp

PAGE 20 PAGE 20 PAGE 21 PAGE 21 PAGE 21 PAGE 22

DISTRIBUTION BLOCK
CMDB10 80A TO 310A (7 TYPES)

65 Amp 80-115 Amp 160-310 Amp 115-175 Amp

PAGE 22 PAGE 23 PAGE 24 PAGE 25

GROUND
CGT4U CGT4N CGT6N CGT10U CGT35U CGMT4

DIN 35 & 32 mm Rail DIN 35 mm Rail DIN 35 mm Rail DIN 35 & 32 mm Rail DIN 35 & 32 mm Rail DIN 15 mm Rail
PAGE 26 PAGE 26 PAGE 27 PAGE 27 PAGE 27 PAGE 27

4 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
SCREW CLAMP 35 & 32 MM DIN RAIL
DISCONNECT
CDTTU CDTTU-SH CKT4U CSDL4U CSDL6U DDDL4U

sliding link sliding link knife contact lever lever double level
PAGE 28 PAGE 28 PAGE 29 PAGE 29 PAGE 29 PAGE 29

FUSE BLOCKS
CSFL4U CSFL4U(L) CAFL4U CAFL4U(L) CAFL4U(N) CSFL6U

Ø5x20, Ø5x25 mm fuse Ø5x20, Ø5x25 mm fuse Ø1/4 inch fuse Ø1/4 inch fuse with LED Ø1/4 inch fuse with Ø5x20, Ø5x25 mm fuse
PAGE 30 with LED PAGE 31 PAGE 31 neon PAGE 31
PAGE 30 PAGE 31

FUSE BLOCKS THERMOCOUPLE

CB1038 DDFL4U DDFL4U(E) DDFL4ULR DDFL4U(E)LR CTT2.5 (4 TYPES)

Ø10x38 mm fuse double level with LED double level with LED temperature measuring
PAGE 32 PAGE 32 PAGE 32 PAGE 33 PAGE 33 PAGE 35

STUD TYPE TERMINAL BLOCKS

CSTSN4U CSTSN5U CSTSB4U CSTSB5U

with nuts with nuts with barrel screws with barrel screws
PAGE 36 PAGE 36 PAGE 37 PAGE 37

INDICATOR/DIODE
CDL4(E)D1/D2 CDL4(E)D3 CDL4U(E)DD1/DD2 CDL4U(E)DD3/DD4 CDL4U(E)D4 CDL4U(E)DD5

for contactors for reverse polarity for lamp testing for lamp testing for lamp testing for lamp testing
and solenoid PAGE 38 PAGE 39 PAGE 39 PAGE 39 PAGE 39
PAGE 38
INDICATOR/DIODE
CDL4U(E)N1 CDL4U(E)LD5 CDL4U(E)LD3 CDL4U(E)LD4 CDL4U(E)LD1/LD2 CDL4U(E)L1/L2 CDL4U(O)

voltage indicator voltage indicator LED voltage indicator LED voltage indicator LED voltage indicator LED voltage indicator LED component carrier
with neon
PAGE 40 PAGE 40 PAGE 41 PAGE 41 PAGE 41 PAGE 41
PAGE 40

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 5
 V i s u a l I n d e x
SURGE SUPPRESSORS
CDL4U(E)LA CDL4U(E)3LA CDL4U(E)MOV CDL4U(E)3SD CDL4U(E)RC

Lightning Arrestor 3 Pole Lightning Arrestor MOV Suppressor Diode RC Circuit

PAGE 42 PAGE 42 PAGE 43 PAGE 43 PAGE 43

TAB CONNECTION TERMINALS CERAMIC TERMINAL BLOCKS

CTC4U CTS4U-TM CDL4U-TM CB4 CB6 CB16

5 connection points Termipoint® Termipoint® for 12 AWG for 10 AWG for 6 AWG
PAGE 44 PAGE 44 PAGE 44 PAGE 45 PAGE 45 PAGE 45

MINI RAIL & PANEL MOUNT

FEED THROUGH SOLDER CONNECTIONS FUSE GROUND
CMT4 CMT4S CMT4SU CSFL4U CSFL4U(L) CGMT4

6 mm 2 solder points 2 uneven solder points Ø5x20, Ø5x25 mm fuse Ø5x20, Ø5x25 mm fuse 6 mm
PAGE 46 PAGE 46 PAGE 47 PAGE 47 with LED PAGE 47
PAGE 47

PANEL MOUNT BUSBAR

CMB4 CENC4/16/35

Custom
6 mm neutral & grounding Assemblies
PAGE 48 PAGE 49
Available

6 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CTS2.5U-N CTS4U-N
FEED-THROUGH
35 or 32mm DIN Rail
Altech “U” Series Universal Rail
Mounting Standard Screw
Clamp Feed through terminals
are the most versatile terminals
for wire-to-wire connection in
control, automation,
instrumentation and power
distribution applications. A
special design feature on the AEx eII EEx eII AEx eII EEx eII
flexible foot enables easy
mounting and dismounting Terminal Width 5 mm 6 mm
from the DIN Rail with the help
Height x Length 45 x 43 mm 45 x 43 mm
of a screwdriver.
Stripping Length 9 mm 9 mm
The terminals with AEx eII
Insulation Material Polyamide 6.6 Polyamide 6.6
EEx eII are explosion proof.
They can be used in Type of Connection 2 screw clamps & 1 tapped hole for cross connection 2screw clamps & 1 tapped hole for cross connection
potentially explosive
atmosphere which may Approvals
C US C US C US C US
occur in chemical and Wire Range 22-12 AWG 0.5-2.5 sq.mm 22-12 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG
petrochemical industry.
These terminals can be used Voltage Rating 600 V 750 V 600 V 600 V 750 V 600 V
in Class 1, Zone 0, 1 & 2
Current Rating 25 A 24 A 25 A 35/40 A* 32 A 35/40A*
hazardous locations. These
terminal blocks comply to Torque 7 lb-in 0.4 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in
En 500019.
Cat. No. Std. Pk. Cat. No. Std. Pk.
Terminal Block CTS2.5U-N 100 CTS4U-N 100

End Plate EP2.5/4UN 50 EP2.5/4UN 50

Isolation Partition PP2.5/4UN 50 PP2.5/4UN 50

Separator Plate SP2.5/4UN 100 SP2.5/4UN 100

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA702 50

COLOR BLOCKS for ordering information CA802 50 CA802 50
refer to page 63
When ordering please add 2 pole
Internal CA721/2 100 CA722/2 100
color suffix to Cat. No. 3 pole
Jumper CA721/3 50 CA722/3 50
4 pole CA721/4 50 CA722/4 50
Example: CTS2.5U-N/R 10 pole CA721/10 10 CA722/10 10
100 pole CA721/100 10 CA722/100 10
Color Ordering
Suffix Insulated 2 pole CA741/2 100 CA742/2 100
Red R Internal 3 pole CA741/3 50 CA742/3 50
Blue BU Jumper 4 pole CA741/4 50 CA742/4 50
10 pole CA741/10 10 CA742/10 10
Black BL
100 pole CA741/100 10 CA742/100 10
Orange O
Green G Current 2 pole CA703/01 100 CA703/1 100
Yellow Y Bars 3 pole CA704/01 100 CA704/1 100
White W 4 pole CA705/01 100 CA705/1 100
10 pole CA731/10 100 CA732/10 100
10 pole (breakable) — CA732/10-A 100
100 pole CA731/100 10 CA732/100 10

Shorting Sleeve & Screw CA 707/S/Q/01 100 CA707/S/Q/01 100

External 2 pole CA717/2 100 CA713/2 100

Jumper 3 pole CA717/3 100 CA713/3 100
4 pole CA717/4 100 CA713/4 50
10 pole CA717/10 25 CA713/10 25

Marking Tags MT5 100 MT6 100

* 35A with one No. 10 AWG and
40A with two No. 12 AWG wires.

12 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CTS6U CTS10U CTS16U CTS25U

AEx eII EEx eII AEx eII EEx eII AEx eII EEx eII

8 mm 10 mm 12 mm 12 mm

47 x 43 mm 47 x 43 mm 47 x 43 mm 56 x 49.5 mm

12 mm 12 mm 16 mm 18 mm

Polyamide 6.6 Polyamide 6.6 Polyamide 6.6 Polyamide 6.6

2 screw clamps & 1 tapped hole for cross connection 2 screw clamps & 1 tapped hole for cross connection 2 screw clamps & 1 tapped hole for cross connection 2 screw clamps & 1 tapped hole for cross connection

C US C US C US C US C US C US C US C US

22-8 AWG 1.5-6 sq.mm 22-8 AWG 22-6 AWG 1.5-10 sq.mm 16-6 AWG 22-6 AWG 2.5-16 sq.mm 20-4 AWG 12-2 AWG 6-25 sq.mm 14-2 AWG

600 V 750 V 600 V 600 V 750 V 600 V 600 V 800 V 600 V 600 V 750 V 600 V

50 A 41 A 50 A 65 A 57 A 65 A 70 A 76 A 85 A 115 A 101 A 115 A

9 lb-in 0.8 Nm 14 lb-in 14 lb-in 1.2 Nm 14 lb-in 14 lb-in 1.2 Nm 14 lb-in 25 lb-in 2.0 Nm 25 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.
CTS6U 100 CTS10U 100 CTS16U 50 CTS25U 50

EP6/10U 50 EP6/10U 50 EP25U 50

PP6/10U 50 PP6/10U 50 PP25U 50

SP6/10U 100 SP6/10U 100 SP6/10U 100

CA702 50 CA702 50 CA702 50 CA702 50

CA802 50 CA802 50 CA802 50 CA802 50

CA723/2 100 CA724/2 100 CA751/2 50 CA725/2 50

CA723/3 50 CA724/3 50 CA751/3 50 CA725/3 25
CA723/4 50 CA724/4 50 CA751/4 50 CA725/4 25
CA723/10 10 CA724/10 10 CA751/10 10 CA725/10 10

CA743/2 100 CA744/2 100 CA761/2 50 CA745/2 50

CA743/3 50 CA744/3 50 CA761/3 50 CA745/3 25
CA743/4 50 CA744/4 50 CA761/4 50 CA745/4 25
CA743/10 10 CA744/10 10 CA761/10 10 CA745/10 10

CA703/2 100 CA703/3 100 CA703/8 100 CA703/4 100

CA704/2 100 CA704/3 100 CA704/8 100 CA704/4 100
CA705/2 100 CA705/3 100 CA705/8 100 CA705/4 100
CA733/10 100 CA734/10 100 CA739/10 100 CA735/10 100

CA707/S/Q/1 100 CA707/S/Q/1 100 CA707/S/Q/5 100 CA707/S/Q/2 100

CA710/2 100 CA718/2 100

CA710/3 100 CA718/3 50
CA710/4 100 CA718/4 50
CA710/10 25 CA718/10 25

MT8 100 MT10 100 MT12 100 MT12 100

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 13
 CTS35U CTS50U CTS95U

AEx eII EEx eII

Terminal Width 15 mm 20.5 mm 25 mm

Height x Length 58 x 52.5 mm 75.5 x 71 mm 90 x 83 mm

Stripping Length 18 mm 22 mm 24 mm

Insulation Material Polyamide 6.6 Polyamide 6.6 Polyamide 6.6

Type of Connection 2 screw clamps & 1 tapped hole for cross connection 2 screw clamp connections 2 Allen screw clamp connections

Approvals
C US C US C US C US C US C US

Wire Range 8-2 AWG 10-35 sq.mm 18-1/0 AWG 6-2/0 AWG 16-50 sq.mm 6-2/0 AWG 2-4/0 AWG 16-50 sq.mm 6-2/0 AWG

Voltage Rating 600 V 750 V 600 V 600V 1000 V 600 V 600V 1000 V 600 V

Current Rating 145 A 125 A 145 A 150 A 150 A 150 A 230 A 150 A 150 A

Torque 25 lb-in 2.5 Nm 25 lb-in 60 lb-in 6.8 Nm 60 lb-in 60 lb-in 6.8 Nm 60 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.
Terminal Block CTS35U 50 CTS50U 20 CTS95U 10

End Plate EP35U 50

Isolation Partition PP35U 50
Separator Plate

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA202 50 CA202 50

for ordering information CA102 50 CA102 50
CA802 50
refer to page 63

Internal CA726/2 50
Jumper CA726/3 25
CA726/4 25
CA726/10 10
Insulated CA746/2 50
Internal CA746/3 25
Jumper CA746/4 25
CA746/10 10

Current CA703/5 100

Bars CA704/5 100
CA705/5 100
CA736/10 100

Shorting Sleeve & Screw CA707/S/Q/2 100

Marking Tags MT15 100 MT20 100 MT25 100

14 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CMC1-2 CMC2-2
FEED-THROUGH
MULTI-CONNECTION
35 or 32mm DIN Rail
Connect multiple wires to a
single terminal block and
eliminate reliability problems
encountered when connecting
two wires into a single clamp.
Two versions are available.

Type CMC1-2 features a single

screw-cage clamp for 22-10
AWG wires on one side and Terminal Width 6 mm 6 mm
two clamps on the other side
Height x Length 47 x 46.5 mm 51.5 x 65 mm
for 22-10 AWG wires.
Stripping Length 9 mm 9 mm
Type CMC2-2 has two identical
clamps for 22-10 AWG wires on Insulation Material Polyamide 6.6 Polyamide 6.6
both sides. Type of Connection 3screw clamps & 1 tapped hole for cross connection 4screw clamps & 2 tapped holes for cross connection

Approvals C US C US C US C US

Wire Range 22-10AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG

Voltage Rating 600 V 600 V 600 V 600 V 600 V 600 V

Current Rating 35 A 32 A 35 A 35 A 32 A 35 A

Torque 7 lb-in. 0.5 Nm 7 lb-in. 7 lb-in. 0.5 Nm 7 lb-in.

Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block CMC1-2 100 CMC2-2 50

End Plate EPCMC1-2 50 EPCMC2-2 50

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA702 50

for ordering information CA802 50 CA802 50
refer to page 63

Internal 2 pole CA722/2 100 CA722/2 100

Jumper 3 pole CA722/3 50 CA722/3 50
4 pole CA722/4 50 CA722/4 50
10 pole CA722/10 10 CA722/10 10
100 pole CA722/100 5 CA722/100 5

Insulated 2 pole CA742/2 100 CA742/2 100

Internal 3 pole CA742/3 50 CA742/3 50
Jumper 4 pole CA742/4 50 CA742/4 50
10 pole CA742/10 10 CA742/10 10
100 pole CA742/100 5 CA742/100 5

Current 2 pole CA703/1 100 CA703/1 100

Bars 3 pole CA704/1 100 CA704/1 100
4 pole CA705/1 100 CA705/1 100
10 pole CA732/10 100 CA732/10 100
10 pole (breakable) CA732/10-A 100 CA732/10-A 100
100 pole CA732/100 10 CA732/100 10

Shorting Sleeve & Screw CA707/S/Q/01 100 CA707/S/Q/01 100

External 2 pole CA713/2 100 CA713/2 100

Jumper 3 pole CA713/3 100 CA713/3 100
for use in upper level 4 pole CA713/4 50 CA713/4 50
10 pole CA713/10 25 CA713/10 25

Marking Tags (MT Type) MT6 100 MT6 100

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 15
 CDL4U CDL4U(I.S)
FEED-THROUGH
DOUBLE LEVEL
35 or 32mm DIN Rail
Altech double level terminals
are the answer to high wiring
density problems posed by
certain unavoidable wiring
arrangements. Double level
terminals have the following
advantages:

• Double wiring density Terminal Width 6 mm 6 mm

available without extension 54 x 55.5 mm 54 x 55.5 mm
Height x Length
of mounting rails.
• Interconnection/shorting can Stripping Length 9 mm 9 mm
be done at both levels.
• Marking/identification by Insulation Material Polyamide 6.6 Polyamide 6.6
marking tags possible at 4screw clamps & 2 tapped holes for cross connection 4screw clamps & 1 tapped hole for cross connection
Type of Connection
both levels.
Approvals C US C US
C US C US
CDL4U(I.S) internally shorted
double level terminals are Wire Range 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG
useful for distribution 300V 400 V 600 V 300 V 400 V 600 V
Voltage Rating
applications by using shorting
links at lower levels. Current Rating 35 A 32 A 35 A 35 A 32 A 35 A

Torque 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block CDL4U 100 CDL4U(I.S) 100

End Plate EPCDL4U 50 EPCDL4U 50

Separator Plate SPCDL4U 100 SPCDL4U 100

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA702 50

for ordering information CA802 50 CA802 50
refer to page 63

Internal 2 pole CA727/2 100 CA727/2 100

Jumper 3 pole CA727/3 50 CA727/3 50
4 pole CA727/4 50 CA727/4 50
10 pole CA727/10 10 CA727/10 10
Insulated 2 pole CA747/2 100 CA747/2 100
Internal 3 pole CA747/3 50 CA747/3 50
Jumper 4 pole CA747/4 50 CA747/4 50
10 pole CA747/10 10 CA747/10 10
Current 2 pole CA703/1 100 CA703/1 100
Bars 3 pole CA704/1 100 CA704/1 100
4 pole CA705/1 100 CA705/1 100
10 pole CA732/10 100 CA732/10 100
10 pole (breakable) CA732/10-A 100 CA732/10-A 100
100 pole CA732/100 10 CA732/100 10

Shorting Sleeve & Screw CA607/S/Q 100 CA607/S/Q 100

External 2 pole CA714/2 100 CA714/2 100

Jumper 3 pole CA714/3 100 CA714/3 100
4 pole CA714/4 50 CA714/4 50
10 pole CA714/10 25 CA714/10 25

Marking Tags (MT Type) MT2 100 MT2 100

16 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 ODL4U
FEED-THROUGH
OFFSET DOUBLE LEVEL

Altech Offset Double Level

Terminals, like CDL Double
Level Terminals, provide a
separate connection possibility
at two levels. In ODL, the top
level is offset from the bottom
level by half the thickness of
Terminal Width 6 mm
the terminal.
In ODL terminals, the bottom Height x Length 63 x 68 mm
level screws have better
Stripping Length 9 mm
accessibility for
tightening/loosening. Insulation Material Polyamide 6.6
*It is recommended to use end Type of Connection 4screw clamps & 2 tapped holes for cross connection
plates at both ends of
assembled ODL terminal sets Approvals
C US C US
for flat alignment to enable
effective use of end stops. Wire Range 22-10 AWG 0.5-4 sq.mm 22-10 AWG

Voltage Rating 600 V 600 V 600 V

Current Rating 35 A 32 A 35 A

Torque 7 lb-in 0.5 Nm 7 lb-in

Cat. No. Std. Pk.

Terminal Block ODL4U 50

End Plate* Front EPODL4U 50

Back EP1ODL4U 50

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50

for ordering information CA802 50
refer to page 63

Internal 2 pole CA727/2 10

Jumper 3 pole CA727/3 10
4 pole CA727/4 10
10 pole CA727/10 10
Insulated 2 pole CA747/2 100
Internal 3 pole CA747/3 50
Jumper 4 pole CA747/4 50
10 pole CA747/10 10
Current 2 pole CA703/1 100
Bars 3 pole CA704/1 100
4 pole CA705/1 100
10 pole CA732/10 100
10 pole (breakable) CA732/10-A 100
100 pole CA732/100 10
Shorting Sleeve & Screw CA607/S/Q 100
External 2 pole CA714/2 100
Jumper 3 pole CA714/3 100
4 pole CA714/4 50
10 pole CA714/10 25
Marking Tags (MT Type) MT6 100

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 17
 CTL2.5U-H CTL2.5U
FEED-THROUGH
TRIPLE LEVEL
35 or 32mm DIN Rail
For applications with extreme
space constraints. Only 6mm
(.236”) wide, with three
separate feed-through levels.
Jumpers can be used to
reduce field wiring.

They can also be used in Terminal Width 6 mm 6 mm

control systems where sensors
Height x Length 67 x 61 mm 67 x 84 mm
and actuator applications are
involved. Stripping Length 9 mm 9 mm

CTL2.5U-H - the top level Insulation Material Polyamide 6.6 Polyamide 6.6
provides connecting points for
Type of Connection 4Screw clamps & 3 tapped holes for cross connection 6Screw clamps & 3 tapped holes for cross connection
signal while middle and
bottom level points are used Approvals
for positive and negative C US C US
potentials. CTL2.5U-H(L) and
CTL2.5U(L) are ideal for Wire Range 22-12 AWG 0.5-2.5 sq.mm 22-12 AWG 22-12 AWG 0.5-2.5 sq.mm 22-12 AWG
providing signal indication.
Voltage Rating 300 V 500 V 300 V 300 V 500 V 300 V

Current Rating 25 A 24 A 25 A 25 A 24 A 25 A

Torque 4.5 lb-in 0.4 Nm 4.5 lb-in 4.5 lb-in 0.4 Nm 4.5 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block CTL2.5U-H 50 CTL2.5U 50

End Plate EPCTL2.5U-H 50 EPCTL2.5U 50

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA702 50

for ordering information CA802 50 CA802 50
refer to page 63
2 pole CA722/2 100 CA722/2 100
Internal 3 pole CA722/3 50 CA722/3 50
Jumper 4 pole CA722/4 50 CA722/4 50
10 pole CA722/10 10 CA722/10 10
100 pole CA722/100 5 CA722/100 5

2 pole CA703/1 100 CA703/1 100

Current 3 pole CA704/1 100 CA704/1 100
Bars 4 pole CA705/1 100 CA705/1 100
10 pole CA732/10 100 CA732/10 100
10 pole (breakable) CA732/10-A 100 CA732/10-A 100
100 pole CA732/100 10 CA732/100 10
Shorting Sleeve & Screw CA707/S/Q/01 100 CA707/S/Q/01 100
External 2 pole CA715/2 100 CA715/2 100
Jumper 3 pole CA715/3 100 CA715/3 100
4 pole CA715/4 100 CA715/4 100
10 pole CA715/10 50 CA715/10 50
Marking Tags (MT Type) MT2 100 MT2 100

18 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CTL2.5U-H(L)* CTL2.5U(L)*

6 mm 6 mm

67 x 61 mm 67 x 84 mm

9 mm 9 mm

Polyamide 6.6 Polyamide 6.6

4Screw clamps & 2 tapped holes for cross connection 6Screw clamps & 2 tapped holes for cross connection

C US C US

22-12 AWG 0.5-2.5 sq.mm 22-12 AWG 22-12 AWG 0.5-2.5 sq.mm 22-12 AWG

300 V 500 V 300 V 300 V 500 V 300 V

25 A 24 A 25 A 25 A 24 A 25 A

4.5 lb-in 0.4 Nm 4.5 lb-in 4.5 lb-in 0.4 Nm 4.5 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk.

CTL2.5U-H(L)* 50 CTL2.5U(L)* 50

EPCTL2.5U-H 50 EPCTL2.5U 50

Ideal for sensor applications.

CA702 50 CA702 50
CA802 50 CA802 50 See Altech’s Inductive Proximity Sensor
catalog for ordering information.
CA722/2 100 CA722/2 100
CA722/3 50 CA722/3 50
CA722/4 50 CA722/4 50
CA722/10 10 CA722/10 10
CA722/100 5 CA722/100 5

CA703/1 100 CA703/1 100

CA704/1 100 CA704/1 100
CA705/1 100 CA705/1 100
CA732/10 100 CA732/10 100
CA732/10-A 100 CA732/10-A 100
CA732/100 10 CA732/100 10

CA707/S/Q/01 100 CA707/S/Q/01 100

CA715/2 100 CA715/2 100

CA715/3 100 CA715/3 100
CA715/4 100 CA715/4 100
CA715/10 50 CA715/10 50

MT2 100 MT2 100

* Add required voltage to part number as suffix;

i.e. CTL2.5U(L)/24 for 24V DC

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 19
 CDB4 CDB4(1)
DISTRIBUTION BLOCK
Altech CDB Compact
Distribution Blocks are an ideal
choice for a simplified
distribution system. A lug/bolt
secures the incoming cable
and the screw clamp design of
the block provides the
outgoing connections. These
provide easy connect points
and ensure perfect continuity
for distribution. A protective
shield effectively shrouds the
incoming connection. Terminal Width 6 mm 6 mm

Height & Width 45 x 43 mm 45 x 43 mm

Application Information:
Sum of outgoing currents on Stripping Length 9 mm 9 mm
either side of center should
Insulation Material Polyamide 6.6 Polyamide 6.6
not exceed half the maximum
permissible incoming current. Type of Connection Input 1 Lug/bolt connection for ring lug 1 Lug/bolt connection for ring lug

Output Screw clamp connection Screw clamp connection

Sum of total outgoing currents
should not exceed maximum
Approvals
permissible incoming current. C US C US

Wire Range Input 10-8 AWG 6-16 sq.mm 10-8 AWG 10-8 AWG 6-16 sq.mm 10-8 AWG
Connection for higher Output 22-12 AWG 0.5-4 sq.mm 22-10 AWG 22-12 AWG 0.5-4 sq.mm 22-10 AWG
outgoing currents should be
Voltage Rating 600 V 750 V 600 V 600 V 750 V 600 V
done through the terminal
nearest to the incoming Current Rating Input 50 A 50 A 50 A 50 A
connection. Max. Individual Output 25 A 32 A 35 A 25 A 32 A 35 A

CMDB blocks are the modified Torque Input 26 lb-in 2.0 Nm 26 lb-in 26 lb-in 2.0 Nm 26 lb-in
Output 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in
version of CDB terminal blocks
without central incoming
terminal connections. Cat. No. H x W x L (mm) Outputs Cat. No. H x W x L (mm) Outputs
Terminal Block CDB4/1 45 x 43 x 43.8 4 CDB4/2 (1) 45 x 43 x 52 4
CDB4/2 45 x 43 x 55.8 8 CDB4/3 (1) 45 x 43 x 58 6
CDB4/3 45 x 43 x 67.8 12 CDB4/4 (1) 45 x 43 x 64 8
CDB4/4 45 x 43 x 80 16 CDB4/5 (1) 45 x 43 x 70 10
CDB4/5 45 x 43 x 96 20 CDB4/6 (1) 45 x 43 x 76 12
CDB4/10 (1) 45 x 43 x 100 20
CDB4/11 (1) 45 x 43 x 106 22

Cat. No. Std. Pk. Cat. No. Std. Pk.

DIN Rail
for ordering information
refer to page 62

End Stop
CA702 50 CA702 50
for ordering information
refer to page 63 CA802 50 CA802 50

Marking Tags (MT Type) MT6 100 MT6 100

20 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CDB6 CDB10 CMDB4

8 mm 10 mm 6 mm

43 x 47 mm 43 x 47 mm 45 x 43 mm

12 mm 12 mm 9 mm

Polyamide 6.6 Polyamide 6.6 Polyamide 6.6

1 Lug/bolt connection for ring lug 1 Lug/bolt connection for ring lug
Screw clamp connection
Screw clamp connection Screw clamp connection

C US C US

10-6 AWG 6-25 sq.mm 10-2 AWG 7-2 AWG 10-35 sq.mm 8-1/0 AWG
22-10 AWG 0.5-4 sq.mm 22-10 AWG
22-8 AWG 1.5-6 sq.mm 22-8 AWG 15-7 AWG 1.5-10 sq.mm 22-6 AWG

600 V 750 V 600 V 600 V 750 V 600 V 600 V 800 V 600 V

100 A 100 A 125 A 130 A

35 A 32 A 35 A
50 A 41 A 50 A 65 A 57 A 65 A

25 lb-in 3.0 Nm 35 lb-in 53 lb-in 6.0 Nm 53 lb-in

7 lb-in 0.5 Nm 7 lb-in
9 lb-in 0.8 Nm 14 lb-in 14 lb-in 1.2 Nm 14 lb-in

Cat. No. H x W x L (mm) Outputs Cat. No. H x W x L (mm) Outputs Cat. No. H x W x L (mm) Outputs
CDB6/2 43 x 47 x 64 8 CDB10/2 43 x 47 x 72 8 CMDB4/2 45 x 43 x 13.5 4
CDB6/3 43 x 47 x 80 12 CDB10/3 43 x 47 x 92 12 CMDB4/3 45 x 43 x 19.5 6
CDB6/4 43 x 47 x 96 16 CDB10/4 43 x 47 x 112 16 CMDB4/4 45 x 43 x 25.5 8
CMDB4/10 45 x 43 x 61.5 20

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

CA702 50 CA702 50 CA702 50

CA802 50 CA802 50 CA802 50

MT8 100 MT10 100 MT6 100

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 21
 CMDB6 CMDB10

Terminal Width 8 mm 10 mm

Height & Width 43 x 47 mm 43 x 47 mm

Stripping Length 12 mm 12 mm

Insulation Material Polyamide 6.6 Polyamide 6.6

Type of Connection Input

Screw clamp connection Screw clamp connection
Output

Approvals

Wire Range Input

Output 22-8 AWG 1.5-6 sq.mm 22-8 AWG 15-7 AWG 1.5-10 sq.mm 20-6 AWG

Voltage Rating 600 V 800 V 600 V 600 V 800 V 600 V

Current Rating Input

Max. Individual Output 50 A 41 A 50 A 65 A 57 A 65 A

Torque Input 9 lb-in 0.8 Nm 14 lb-in 14 lb-in 1.2 Nm 14 lb-in

Output

Cat. No. H x W x L (mm) Outputs Cat. No. H x W x L (mm) Outputs

Terminal Block CMDB6/2 43 x 48 x 17.5 4 CMDB10/2 43 x 48 x 21.5 4
CMDB6/3 43 x 48 x 25.5 6 CMDB10/3 43 x 48 x 31.5 6
CMDB6/4 43 x 48 x 33.5 8 CMDB10/4 43 x 48 x 41.5 8
CMDB6/10 43 x 48 x 81.5 20 CMDB10/10 43 x 48 x 101.5 20

Cat. No. Std. Pk. Cat. No. Std. Pk.

DIN Rail
for ordering information
refer to page 62

End Stop
for ordering information CA702 50 CA702 50
refer to page 63 CA802 50 CA802 50

Marking Tags (MT Type) MT8 100 MT10 100

22 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 38049 38041
ONE PHASE POWER
DISTRIBUTION BLOCKS
• Speed of mounting and wiring
• IP20 Finger Safe
• DIN Rail or Panel Mount
• Blocks fit with other DIN Rail
mountable modular devices
(height 95mm, depth 44.5mm)
• Accessories increase the
number of outputs with only
one input.

Part Number:
White 38049 38041
Gray (RoHS compliant) DB16 DB35

Approvals
Fork Type Busbar
38045 Current Rating 80A 80A 115A 125A

Voltage Rating 600V AC 690V AC 600V AC 690V AC

No. of Inputs 1 1 1 1
Wire Range 8-4 AWG 6-16mm2 8-2 AWG 10-35mm2
Torque 13.5lb. in. 1.5Nm 31lb. in. (40 for 3.5Nm
38041
No. of Outputs 6 6 6 DB35) 6
Wire Range 2x8-4 AWG 2x6-16mm2 14-6 AWG 2.5-16mm2
Torque 13.5lb. in. 1.5Nm 17.5lb. in. 2Nm
Wire Range 4x14-10 AWG 4x2.5-6mm2
Torque 7.2lb. in. 0.8Nm

Optional
Marking Tag MT2 MT2
(for DB16 ad DB35)

38049
5
5

4
4

Dimensions:
75mm (2.95 in.)
66mm (2.60 in.)

62mm (2.44 in.)

54mm (2.13 in.)

38032 Copper Jumper Bar

3803221

6.5
6 47mm (1.85 in.) 6.5 42.5mm (1.67 in.)
6
27mm
(1.06 in.) 27mm
(1.06 in.)

Accessories 38041
Part Number: Fork Type Busbar
5

38045 to jump 2 Blocks

4

38046 to jump 8 Blocks

75mm (2.95 in.)

62mm (2.44 in.)

can be cut to customer needs

2mm
(0.08 in.)
(0.63 in.)
16mm
(0.20 in.)

15mm
5mm

6.5 42.5mm (1.67 in.)

6 (0.59 in.)

27mm
(1.06 in.)
26.63mm 6mm
(1.05 in.) (0.24 in.)
11.25mm
(0.44 in.)
35 Royal Road, Flemington, NJ 08822-6000 • (tel.) 908-806-9400 • (fax) 908-806-9490 • www.altechcorp.com
(0.33 in.)
8.4mm

44mm (1.73 in.) 38045

205mm (8.07 in.) 38046

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 23
 38032 38020 38019

Part Number: 38032 38020 38019

Approvals

Current Rating 160A 160A 230A 250A 310A 400A

Voltage Rating 600V AC 690V AC 600V AC 690V AC 600V AC 690V AC

No. of Inputs 1 1 1 1 1 1
Wire Range 8-2/0AWG 10-70mm2 2-4/0AWG 35-120mm2 3/0-350kcmil 95-185mm2
Torque 35.5lb. in. 4Nm 170lb. in. 19Nm 230lb. in. 25Nm

No. of Outputs 6 6 11 11 11 11
Wire Range 14-6 AWG 2.5-16mm2 2x 14-2AWG 2.5-35mm2 2x 14-2AWG 2.5-35mm2
Torque 17.5lb. in. 2Nm 31lb. in. 3.5Nm 31lb. in. 3.5Nm
Wire Range 5x 14-6AWG 2.5-16mm2 5x 14-6AWG 2.5-16mm2
Torque 17.5lb. in. 2Nm 17.5lb. in. 2Nm
Wire Range 4x 14-8AWG 2.5-10mm2 4 x 14-8AWG 2.5-10mm2
Torque 17.5lb. in. 2Nm 17.5lb. in. 2Nm

Dimensions:

88mm (3.46 in.)

81.5mm (3.20 in.)
92mm (3.62 in.)

101mm (3.98 in.)

101mm (3.98 in.)

88mm (3.46 in.)

35mm 49mm (1.93 in.)

(1.38 in.) 45mm 50mm (1.97in.) 45mm 50mm (1.97 in.)
(1.77 in.) (1.77 in.)

Accessories
Part Number: Copper Jumper Bar
3803221 for 2 Blocks
3803231 for 3 Blocks
3803241 for 4 Blocks
can be cut to customer needs
(0.59 in.)
15mm

59mm (2.32 in.) 3803221 4mm

130mm (5.12 in.) 3803241 (0.16 in.)

24 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 38075 38073
THREE PHASE POWER
DISTRIBUTION BLOCKS
• Speed of mounting
and wiring
• IP20 Finger Safe
• DIN Rail or Panel Mount
• Blocks fit with other DIN Rail
mountable modular devices
• Same compact size for 3 Pole
both ratings

Part Number: 38075 38073

Approvals

Current Rating 115A 115A 175A 175A

Voltage Rating 600V AC 690V AC 600V AC 690V AC

No. of Inputs 3x1 3x1 3x1 3x1

Wire Range 8-2AWG 10-35mm2 8-2/0AWG 10-70mm2
Torque 31lb. in. 3.5Nm 35.5lb. in. 4Nm

No. of Outputs 3x6 3x6 3x6 3x6

Wire Range 14-4AWG 2.5-16mm2 14-4AWG 2.5-16mm2
Torque 17.5lb. in. 2Nm 17.5 lb. in. 2Nm

Dimensions:

5.2mm (0.20 in.)

58mm (2.28 in.)
71mm (2.80 in.)

52.5mm (2.07 in.) 43mm (1.69 in.)

80.1mm (3.15 in.)

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 25
 CGT4U CGT4N
GROUND
35 and 32mm DIN Rail
Use ground blocks instead of
grounding studs and wire lugs to
terminate ground wires, saving
installation and wiring time.

Ground blocks clamp mechanically

onto the DIN Rail by tightening the
center mounting screw, making a
reliable electrical connection between
the cage clamp terminals and the DIN AEx eII EEx eII
Rail. The rail serves as a busbar and
Terminal Width 6 mm 6 mm
automatically distributes ground
potential to all other ground terminals Height x Length 48 x 43 mm 45.4 x 54.2 mm
on the same rail.
Stripping Length 9 mm 9 mm
Ground blocks can also be used
as end stops, preventing other Insulation Material Polyamide 6.6 Polyamide 6.6
terminal blocks and components from
moving laterally on the DIN Rail. Type of Connection 2 screw clamps 2 screw clamps

They are supplied with a standard Approvals

C US C US

green/yellow housing for easy

Wire Range 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG
identification and accept standard
marking tags.
Torque 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.8 Nm 7 lb-in

CGT4U, CGT10U and CGT35U can be

mounted on both DIN 32mm and DIN Cat. No. Std. Pk. Cat. No. Std. Pk.
35mm rails.
Terminal Block CGT4U 50 CGT4N 50
CGT4N & CGT6N can be mounted on
35mm DIN rail and have the same top DIN Rail
outer profile as the feed through for ordering information
refer to page 62
blocks (CTS4U-N, CTS2.5U-N, CTS6U,
CTS10U).
Marking Tags
MT6 100 MT6 100
(MT Type)
CGMT4 can be mounted on 15mm
DIN rails and has the same top outer
profile as the CMT4 feed through
blocks.

• High density
• Screw-cage clamp
• Special clamping foot
• Polyamide 6.6
• Color: green/yellow

Assembly for single phase

3 wire circuits.

26 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CGT6N CGT10U CGT35U CGMT4

AEx eII EEx eII

8 mm 10 mm 16 mm 6 mm

47 x 54.5 mm 49.5 x 45 mm 61.5 x 58 mm 28.5 x 27 mm

12 mm 12 mm 18 mm 9 mm

Polyamide 6.6 Polyamide 6.6 Polyamide 6.6 Polyamide 6.6

2 screw clamps 2 screw clamps 2 screw clamps 2 screw clamps

C US C US C US C US

22-8 AWG 1.5-6 sq.mm 22-8 AWG 22-6 AWG 1.5-10 sq.mm 16-8 AWG 8-2 AWG 10-35 sq.mm 8-2 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG

14 lb-in 0.8 Nm 14 lb-in 14 lb-in 1.2 Nm 14 lb-in 25 lb-in 2.5 Nm 25 lb-in 7 lb-in 0.5 Nm 7 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

CGT6U 50 CGT10U 50 CGT35U 20 CGMT4 50

MT8 100 MT10 100 MT15 100 MT2 100

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 27
 CDTTU CDTTU-SH
DISCONNECT
35 or 32mm DIN Rail
Disconnect and test terminals are
an ideal choice for measuring
control and regulatory circuits. The
terminals provide a clear functional
advantage for devices having
utility instruments and associated
transformers.

Five versions of disconnect and

test terminals are available:

• CDTTU - disconnection is
achieved by means of a slide
Terminal Width 8 mm 16 mm
link operated with a screw driver.
Height x Length 57 x 63 mm 57 x 63 mm
• CDTTU-SH - disconnect and test
terminals are ideal for use in Stripping Length 12 mm 12 mm
current transformer applications
Insulation Material Polyamide 6.6 Polyamide 6.6
when it is mandatory to keep the
secondary side shorted at any Type of Connection 2 screw clamps 4 screw clamps
point while taking current
measurements. Approvals
C US C US

• CKT4U - disconnection is Wire Range 16-8 AWG 1.5-6 sq.mm 16-8 AWG 16-8 AWG 1.5-6 sq.mm 16-8 AWG
achieved by lifting the
knife contact lever. Voltage Rating 600 V 750 V 600 V 300 V 300 V 600 V

• CSDL4U - hinged diconnection Current Rating 41 A 41 A 41 A 10 A 10 A 10 A

and testing terminal, Torque 14 lb-in 1.2 Nm 14 lb-in 14 lb-in 1.6 Nm 14 lb-in
incorporates a connecting link in
place of the fuse link.
Cat. No. Std. Pk. Cat. No. Std. Pk.
• CSDL6U - hinged disconnect
Terminal Block CDTTU 50 CDTTU-SH 50
block for 8 AWG size wires.
End Plate EPCDTTU 50 EPCDTTU 50
• DDDL4U - double level
disconnect terminal with hinged Isolation Partition
disconnect in upper level.
DIN Rail
for ordering information
Specially designed socket head refer to page 62
screws act as test/monitoring
points in both CDTTU, CDTTU-SH
End Stop CA702 50 CA702 50
and CKT4U. for ordering information CA802 50 CA802 50
refer to page 63
Important: The disconnecting
device is not suitable for External 2 pole CA710/2 100 CA710/2 100
Jumper 3 pole CA710/3 100 CA710/3 100
interrupting load. The supply must for internal jumpers 4 pole CA710/4 100 CA710/4 100
be switched off before operating refer to page 60 10 pole CA710/10 25 CA710/10 25
the slide link/lever.
MT8 100 MT8 100
Marking Tags (MT Type)
(MT Type on Lever)

28 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CKT4U CSDL4U CSDL6U DDDL4U

6 mm 8 mm 8 mm 8 mm

46 x 46.3 mm 43 x 58 mm 60 x 43 mm 66 x 88 mm

9 mm 9.5 mm 9.5 mm 9.5 mm

Polyamide 6.6 Polyamide 6.6 Polyamide 6.6 Polyamide 6.6

2 screw clamps 2 screw clamps 2 screw clamps 4 screw clamps

C US C US C US C US

22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-8 AWG 1.5-6 sq.mm 22-8 AWG 22-10 AWG 22-10 AWG

600 V 750 V 600 V 600 V 750 V 600 V 300 V 500 V 300 V 600 V 300 V

16 A 16 A 16 A 14 A 6.3 A 14 A 10 A 6.3 A 10 A 14 A 14 / 35 A

7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in 14 lb-in 0.8 Nm 14 lb-in 7 lb-in 7 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

CKT4U 50 CSDL4U 100 CSDL6U 50 DDDL4U 20

EPCKT4U 50 EPCSFL4U 50 EPCSFL6U 50 EPDDFL4U 25

PPCSFL4U 50

CA702 50 CA702 50 CA702 50 CA702 50

CA802 50 CA802 50 CA802 50 CA802 50

CA713/2 100 CA711/2 100 CA710/2 100 CA711/2 100

CA713/3 100 CA711/3 100 CA710/3 50 CA711/3 100
CA713/4 50 CA711/4 50 CA710/4 50 CA711/4 50
CA713/10 25 CA711/10 25 CA710/10 25 CA711/10 25

MT6 100 MT8 100 MT8 100 MT8 100

MT2 100 MT2 100

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 29
 CSFL4U CSFL4U(L)*
FUSE BLOCKS
Certain electrical and control
systems require protection by
fuses. CSFL4U and CSFL6U
have a specially designed space
for cartridge type glass fuse
and accept Ø5 x 20 or Ø5 x 25
mm fuses. CAFL4U accepts
Ø1/4 x 1-1/4 in. fuses. The fuse
can be engaged or disengaged
by the movement of the carrier.
Terminal Width 8 mm 8 mm
Altech fuse terminals are also Height x Length 43 x 58 mm 43 x 58 mm
available with light indication -
CSFL4U(L). A specially designed Stripping Length 9.5 mm 9.5 mm
built-in circuit gives light
Insulation Material Polyamide 6.6 Polyamide 6.6
indication in the event of fuse
blow out. Thus, fault in a circuit Type of Connection 2 screw clamps 2 screw clamps
can be easily located.
Fusion Voltage 24V AC/DC, 48V AC/DC,
110V AC/DC, 220V AC
However, an application of such
terminals must take into Type of Fuse Used Ø5x20, Ø5x25 mm Ø5x20, Ø5x25 mm
consideration residual current
Approvals
flow. C US C US

DDFL4U - Double Level Fuse Wire Range 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG
Terminal with fuse link on the
Voltage Rating 600 V 750 V 600 V 600 V 750 V 600 V
top level has a separate feed
through terminal at the lower Current Rating 6.3 A 6.3 A 8A 6.3 A 6.3 A 8A
level. This eliminates use of an
Torque 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in
additional feed through
terminal. Cat. No. Std. Pk. Cat. No. Std. Pk.

In DDFL4U(E), specially Terminal Block CSFL4U 100 CSFL4U(L)* 50

designed built in circuit gives End Plate EPCSFL4U 50 EPCSFL4U 50
light indication in the event of a
fuse blow out at the top level. Isolation Partition PPCSFL4U 50 PPCSFL4U 50
The terminal provides separate
DIN Rail
feed through connection for ordering information
possibility at the lower level. refer to page 62

DDFL4U(LR): This is a modified

End Stop CA702 50 CA702 50
version of DDFL4U(E) terminal for ordering information CA802 50 CA802 50
where in two equipotential refer to page 63
connection points are available
External 2 pole CA711/2 100 CA711/2 100
on both ends of the terminal. Jumper 3 pole CA711/3 100 CA711/3 100
4 pole CA711/4 50 CA711/4 50
CAFL4U(L) is equipped with a 10 pole CA711/10 25 CA711/10 25
LED for blown fuse indication.
Marking Tags (MT Type) MT8 100 MT8 100
CAFL4U(N) is equipped with a (MT Type on Lever) MT2 100 MT2 100
neon bulb for same application.

CB1038 accepts Ø10 x 38mm

fuse.

Fuses are sold separately

by Altech, see page 34
for details.

* Add required voltage to part number

as a suffix. i.e. CSFL4U(L)/24 for 24V AC/DC.

30 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CAFL4U CAFL4U(L)* CAFL4U(N) CSFL6U

9 mm 9 mm 9 mm 8 mm

50 x 72 mm 50 x 70 mm 50 x 70 mm 60 x 43 mm

12 mm 12 mm 12 mm 12 mm

Polyamide 6.6 Polyamide 6.6 Polyamide 6.6 Polyamide 6.6

2 screw clamps 2 screw clamps 2 screw clamps 2 screw clamps

24V AC/DC, 48V AC/DC, 110-220V AC

110V AC/DC, 220V AC, 300V AC
Ø1/4x1 in., Ø1/4x11/4 in. Ø1/4x1 in., Ø1/4x11/4 in. Ø1/4x1 in., Ø1/4x11/4 in. Ø5x20, Ø5x25 mm

C US C US C US C US

22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-8 AWG 1.5-6 sq.mm 22-8 AWG

600 V 600 V 600 V 600 V 600 V 600 V 600 V 600 V 600 V 300 V 500 V 300 V

16 A 6.3 A 12 A 16 A 6.3 A 12 A 16 A 6.3 A 12 A 10 A 6.3 A 10 A

7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in 14 lb-in 0.8 Nm 14 lb-in
Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

CAFL4U 25 CAFL4U(L)* 25 CAFL4U(N) 25 CSFL6U 50

EPCAFL4U 50 EPCAFL4U 50 EPCAFL4U 50 EPCSFL6U 50

CA702 50 CA702 50 CA702 50 CA702 50

CA802 50 CA802 50 CA802 50 CA802 50

CA716/2 50 CA716/2 50 CA716/2 50 CA710/2 100

CA716/3 50 CA716/3 50 CA716/3 50 CA710/3 100
CA716/4 50 CA716/4 50 CA716/4 50 CA710/4 100
CA716/10 25 CA716/10 25 CA716/10 25 CA710/10 25

MT9 100 MT9 100 MT9 100 MT8 100

* Add required voltage to part number as a suffix.

i.e. CAFL4U(L)/24 for 24V AC/DC.

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 31
 CB1038 DDFL4U DDFL4U(E)*

Terminal Width 17.5 mm 8 mm 8 mm

Height x Length 77 x 63.5 mm 66 x 88 mm 66 x 88 mm

Stripping Length 11 mm 9.5 mm 9.5 mm

Insulation Material Aculon ® Polyamide 6.6 Polyamide 6.6

Type of Connection 2 screw clamps 4 screw clamps 4 screw clamps

Fusion Voltage 24V AC/DC, 48V AC/DC,

110V AC/DC, 220V AC
Type of Fuse Used Ø10 x 38 mm Ø5x20, Ø5x25 mm Ø5x20, Ø5x25 mm

Approvals
C US
C US C US

Wire Range 24-4 AWG 1.5-25sq.mm 24-4 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG

Voltage Rating 600 V 400 V** 600 V 600 V 600 V 600 V 600 V 600 V 600 V

Current Rating Top Level 30A 32A** 30A 6.3 A 6.3 A 8A 6.3 A 6.3 A 8A
Bottom Level 35 A 32 A 35 A 35 A 32 A 35 A

Torque 31 lb-in 2-2.5 Nm 31 lb-in 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block CB1038-1 1 DDFL4U 20 DDFL4U(E)* 20

available up to 4 pole

End Plate EPDDFL4U 25 EPDDFL4U 25

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA702 50 CA702 50

for ordering information CA802 50 CA802 50 CA802 50
refer to page 63
2 pole
Internal CA729/2 100 CA729/2 100
3 pole
Jumper CA729/3 50 CA729/3 50
4 pole
10 pole CA729/4 50 CA729/4 50
CA729/10 10 CA729/10 10
Insulated 2 pole CA749/2 100 CA749/2 100
Internal 3 pole CA749/3 50 CA749/3 50
Jumper 4 pole CA749/4 50 CA749/4 50
10 pole CA749/10 10 CA749/10 10
Current 2 pole
3 pole CA703/6 100 CA703/6 100
Bar CA704/6 100 CA704/6 100
4 pole
10 pole CA705/6 100 CA705/6 100
CA737/10 100 CA737/10 100
Shorting Sleeve & Screw CA707/S/Q/3 100 CA707/S/Q/3 100

External 2 pole CA711/2 100 CA711/2 100

Jumper 3 pole CA711/3 100 CA711/3 100
4 pole CA711/4 50 CA711/4 50
10 pole CA711/10 25 CA711/10 25

Marking Tags (MT Type) MT8 100 MT8 100

(MT Type on Lever) MT2 100 MT2 100

*Add required voltage to part number as a suffix. i.e. DDFL4U(E)/24 for 24V AC/DC. ** 25A @ 500 V, 10A @ 690V, 16A @ 500V for fast blow.

32 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 DDFL4ULR DDFL4U(E)LR*

Terminal Width 8 mm 8 mm

Height x Length 66 x 88 mm 66 x 88 mm

Stripping Length 9.5 mm 9.5 mm

Insulation Material Polyamide 6.6 Polyamide 6.6

Type of Connection 4 screw clamps 4 screw clamps

Fusion Voltage 24V AC/DC, 48V AC/DC,

110V AC/DC, 220V AC
Type of Fuse Used Ø5x20, Ø5x25 mm Ø5x20, Ø5x25 mm

Approvals
C US C US

Wire Range 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG

Voltage Rating 600 V 600 V 600 V 600 V 600 V 600 V

Current Rating Top Level 6.3 A 6.3 A 6.3 A 6.3 A 6.3 A 6.3 A
Bottom Level 35 A 1 32 A 1 35 A 1 35 A 1 32 A 1 35 A 1

Torque 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block DDFL4ULR 20 DDFL4U(E)LR* 20

End Plate EPDDFL4U 20 EPDDFL4U 20

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA702 50

for ordering information CA802 50 CA802 50
refer to page 63
2 pole CA729/2 100 CA729/2 100
Internal
3 pole CA729/3 50 CA729/3 50
Jumper
4 pole CA729/4 50 CA729/4 50
10 pole CA729/10 10 CA729/10 10

Insulated 2 pole CA749/2 100 CA749/2 100

Internal 3 pole CA749/3 50 CA749/3 50
Jumper 4 pole CA749/4 50 CA749/4 50
10 pole CA749/10 10 CA749/10 10

Current 2 pole CA703/6 100 CA703/6 100

Bar 3 pole CA704/6 100 CA704/6 100
4 pole CA705/6 100 CA705/6 100
10 pole CA737/10 100 CA737/10 100

Shorting Sleeve & Screw CA707/S/Q/3 100 CA707/S/Q/3 100

External 2 pole CA711/2 100 CA711/2 100

Jumper 3 pole CA711/3 100 CA711/3 100
4 pole CA711/4 50 CA711/4 50
10 pole CA711/10 25 CA711/10 25

Marking Tags (MT Type) MT8 100 MT8 100

(MT Type on Lever) MT2 100 MT2 100

*Add required voltage to part number as a suffix. i.e. DDFL4U(E)LR/24 for 24V AC/DC. 1 Left or right side connection.

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 33
 5 X 20 5 X 25 6.3 X 32
MINIATURE FUSES
Miniature Fuses are typically
used to protect electronic
devices, laboratory and
measurement instruments,
stereos, TV’s, VCR’s etc. They
are available in four sizes
with a current range of 20mA
to 20 Amps. Miniature Fuses upon request upon request
are manufactured according
to VDE 0820 part 1, VDE 0820
part 2, IEC publication 127,
CEE publication 4 and actual
DIN standards.
The 5x20, 5x25 fuses can be
used in the CSFL4U series
terminal blocks. The 6.3x32
fuse can be used in the
CAFL4U series terminal
blocks.
Operating Class:
Slow, Typical Marking: “T”
Medium, Typical Marking:
“M”
Fast, Typical Marking: “F”
Voltage 250V AC/DC Voltage 250V AC/DC Voltage 250V AC/DC
DIN 41662 DIN 41571-2 DIN 41661 DIN 41571-2
IEC-127-2/III IEC-127-2/II

Cat. No. Cat. No. Cat. No.

Current Slow Medium Fast Medium Slow Fast

20mA 0.02M5x20M
32mA 0.032M5x20M 0.032M5x25M 0.032M6.3x32Tv
40mA 0.04M5x25M 0.04M6.3x32Tv
50mA 0.05M5x20T4 0.05M5x20M 0.05M5x20F4 0.05M5x25M 0.05M6.3x32T4 0.05M6.3x32F
63mA 0.063M5x20M 0.063M5x25M 0.063M6.3x32T4 0.063M6.3x32F
80mA 0.08M5x20T4 0.08M5x20M 0.08M5x25M 0.08M6.3x32T4 0.08M6.3x32F
100mA 0.1M5x20T4 0.1M5x20M 0.1M5x20F4 0.1M5x25M 0.1M6.3x32T4 0.1M6.3x32F
125mA 0.125M5x20T4 0.125M5x20M 0.125M5x20F4 0.125M5x25M 0.125M6.3x32T4 0.125M6.3x32F
160mA 0.16M5x20T4 0.16M5x20M 0.16M5x20F4 0.16M5x25M 0.16M6.3x32T4 0.16M6.3x32F
200mA 0.2M5x20T4 0.2M5x20M 0.2M5x20F4 0.2M5x25M 0.2M6.3x32T4 0.2M6.3x32F
250mA 0.25M5x20T4 0.25M5x20M 0.25M5x20F4 0.25M5x25M 0.25M6.3x32T4 0.25M6.3x32F
315mA 0.315M5x20T4 0.315M5x20M 0.315M5x20F4 0.315M5x25M 0.315M6.3x32T4 0.315M6.3x32F

400mA 0.4M5x20T4 0.4M5x20M 0.4M5x20F4 0.4M5x25M 0.4M6.3x32T4 0.4M6.3x32F

500mA 0.5M5x20T4 0.5M5x20M 0.5M5x20F4 0.5M5x25M 0.5M6.3x32T4 0.5M6.3x32F
630mA 0.63M5x20T4 0.63M5x20M 0.63M5x20F4 0.63M5x25M 0.63M6.3x32T4 0.63M6.3x32F
700mA 0.7M5x20T4 0.7M5x20M 0.7M5x20F4 0.8M5x25M 0.7M6.3x32T4 0.7M6.3x32F
800mA 0.8M5x20T4 0.8M5x20M 0.8M5x20F4 0.8M6.3x32T4 0.8M6.3x32F
1.0A 1.0M5x20T4 1.0M5x20M 1.0M5x20F4 1.0M5x25M 1.0M6.3x32T4 1.0M6.3x32F4
1.25A 1.25M5x20T4 1.25M5x20M 1.25M5x20F4 1.25M5x25M 1.25M6.3x32T4 1.25M6.3x32F4
1.4A 1.4M5x20T4 1.4M5x20M 1.6M5x25M
1.6A 1.6M5x20T4 1.6M5x20M 1.6M5x20F4 1.6M6.3x32T4 1.6M6.3x32F4
2.0A 2.0M5x20T4 2.0M5x20M 2.0M5x20F4 2.0M5x25M 2.0M6.3x32T4 2.0M6.3x32F4
2.5A 2.5M5x20T4 2.5M5x20M 2.5M5x20F4 2.5M5x25M 2.5M6.3x32T4 2.5M6.3x32F2,4

3.15A 3.15M5x20T4 3.15M5x20M 3.15M5x20F4 3.15M5x25M 3.15M6.3x32T4 3.15M6.3x32F2,4

4.0A 4.0M5x20T4 4.0M5x20M 4.0M5x20F4 4.0M5x25M 4.0M6.3x32T4 4.0M6.3x32F2,4
5.0A 5.0M5x20T4 5.0M5x20M 5.0M5x20F4 5.0M5x25M 5.0M6.3x32T4 5.0M6.3x32F3,4
6.3A 6.3M5x20T4 6.3M5x20M 6.3M5x20F4 6.3M5x25M 6.3M6.3x32T4 6.3M6.3x32F3,4
1 Not standard rating. 7.0A 7.0M6.3x32T4 7.0M6.3x32F3
2 Rated Voltage 150V. 8.0A 8.0M5x20T1 8.0M5x20M 8.0M5x20F1 8.0M6.3x32T4 8.0M6.3x32F3
10.0A 10.0M5x20T1 10.0M5x20M 10.0M5x20F1 8.0M5x25M1 10.0M6.3x32T4 10.0M6.3x32F3
3 Rated Voltage 60V.
12.5A 12.5M5x20T1 12.5M5x20M1 12.5M5x20F1 10.0M5x25M1 12.5M6.3x32T4 12.5M6.3x32F3
4 UL recognized version 16.0A 16.0M5x20T1 16.0M5x20M1 16.0M5x20F1 16.0M5x25M1 16.0M6.3x32T4 16.0M6.3x32F3
available upon request. 20.0A 20.0M5x20T1 20.0M5x20M1 20.0M5x20F1 20.0M6.3x32T4 20.0M6.3x32F3

Std. Pk. 10 Std. Pk. 10 Std. Pk. 10

34 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CTT2.5UK/J/T/E
THERMOCOUPLE
TERMINAL BLOCK
Altech thermocouple
terminal blocks are designed
for use in temperature
measuring circuits.

The current carrying part of

the terminal blocks have the
same material (according to
DIN437134 and DIN43714)
which is used for
compensating cables in the
Terminal Width 10 mm
temperature measurement
circuit (up to 200°C). Thus Height x Length 45 x 43 mm
fulfilling the norms stated in
DIN EN60584. Stripping Length 9 mm

The terminal block is marked Insulation Material Polyamide 6.6

for the respective type of
thermocouple which enables Current Carrying Material Chromel/Alumel
easy identification for wiring. (NiCr/NiAl)

• CTT2.5UK ‘K’ type - Type of Connection 4 screw clamps

Chromel (NiCr)
Ratings:
Alumel (NiAl)
Wire Range 22-12 AWG
• CTT2.5UJ ‘J’ type -
Iron (Fe) Voltage Rating 300 V
Constantan (CuNi)
Current Rating 10 A
• CTT2.5UT ‘T’ type -
Copper (Cu) Torque 7 lb-in
Constantan (CuNi)

• CTT2.5UE ‘E’ type - Cat. No. Std. Pk.

Chromel (NiCr)
Constantan (CuNi) Terminal Block CTT2.5UK 50
CTT2.5UJ 50
CTT2.5UT 50
CTT2.5UE 50

End Plate EP2.5/4UN 50

Isolation Plate PP2.5/4UN 50

DIN Rail
for ordering information
refer to page 63

End Clamp CA802 100

CA702 100

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 35
 Stud Type CSTSN4U CSTSN5U
Terminal Blocks
Altech DIN rail mounting Stud
Type Terminal Blocks are
preferred for the connections
that are subjected to very severe
vibrations.

The wire is crimped to a ring /

fork type lug and is screwed on
to the flat current bar in
terminal. The range includes
terminal blocks for wires of size
22-4 AWG.

Jumpering can be achieved with Terminal Width 17 mm 17 mm

the aid of external jumpers. The
Height x Length 44.5 x 50 mm 44.5 x 50 mm
jumpers are insulated to make
them shock proof. The terminal Stripping Length 12 mm 12 mm
blocks have marker holding
recess to accommodate MT type Insulation Material Polyamide 6.6 Polyamide 6.6
marking tags.
Type of Connection 2 screw connection 2 screw connection
for M4 ring/fork lugs for M5 ring/fork lugs
It is recommended to use
protective covers in transparent Approvals 1 1
plastic because assemblies of C US C US

these terminals blocks are not

Wire Range 22-6 AWG 1.5-10 sq.mm 22-6 AWG 22-4 AWG 1.5-16 sq.mm 22-4 AWG
fully covered.
Voltage Rating 600 V 800 V 600 V 600 V 800 V 600 V

Current Rating 65 A 57 A 65 A 80 A 76 A 80 A

Torque 14 lb-in 1.2 Nm 14 lb-in 17.5 lb-in 2.0 Nm 17.5 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block CSTSN4U 100 CSTSN5U 100

End Plate EPCSTSN5U 50 EPCSTSN5U 50

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA702 50

for ordering information CA802 50 CA802 50
refer to page 63

Protective Cover 2 Terminal CSTSPC1 100 CSTSPC1 100

for covering 3 Terminal CSTSPC1-1 100 CSTSPC1-1 100

Protective Cover 100 mm CSTSPC1-2 10 CSTSPC1-2 10

in Length 200 mm CSTSPC1-3 10 CSTSPC1-3 10
300 mm CSTSPC1-4 10 CSTSPC1-4 10

Insulated Removable 2 way CA514/1-2 100 CA514/1-2 100

Jumpers 3 way CA514/1-3 50 CA514/1-3 50
4 way CA514/1-4 50 CA514/1-4 50

Insulated Permanent 2 way CA514/3-2 100 CA514/3-2 100

Jumpers 3 way CA514/3-3 50 CA514/3-3 50
4 way CA514/3-4 50 CA514/3-4 50

Marking Tags (MT Type) MT2 100 MT2 100

1 Approval pending.

36 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CSTSB4U CSTSB5U

Terminal Width 17 mm 17 mm

Height x Length 44.5 x 50 mm 44.5 x 50 mm

Stripping Length 12 mm 12 mm

Insulation Material Polyamide 6.6 Polyamide 6.6

Type of Connection 2 screw connection 2 screw connection

for M4 ring/fork lugs for M5 ring/fork lugs

Approvals 1 1
C US C US

Wire Range 22-6 AWG 1.5-10 sq.mm 22-6 AWG 22-4 AWG 1.5-16 sq.mm 22-4 AWG

Voltage Rating 600 V 800 V 600 V 600 V 800 V 600 V

Current Rating 65 A 57 A 65 A 80 A 76 A 80 A

Torque 14 lb-in 1.2 Nm 14 lb-in 17.5 lb-in 2.0 Nm 17.5 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block CSTSB4U 100 CSTSB5U 100

End Plate EPCSTN5U 50 EPCSTN5U 50

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA702 50

for ordering information CA802 50 CA802 50
refer to page 63

Protective Cover 2 Terminal CSTSPC1 100 CSTSPC1 100

for covering 3 Terminal CSTSPC1-1 100 CSTSPC1-1 100

Protective Cover 100 mm CSTSPC1-2 10 CSTSPC1-2 10

in Length 200 mm CSTSPC1-3 10 CSTSPC1-3 10
300 mm CSTSPC1-4 10 CSTSPC1-4 10

Insulated Removable 2 way CA514/1-2 100 CA514/1-2 100

Jumpers 3 way CA514/1-3 50 CA514/1-3 50
4 way CA514/1-4 50 CA514/1-4 50

Insulated Permanent 2 way CA514/3-2 100 CA514/3-2 100

Jumpers 3 way CA514/3-3 50 CA514/3-3 50
4 way CA514/3-4 50 CA514/3-4 50

Marking Tags (MT Type) MT2 100 MT2 100

1 Approval pending.

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 37
 CDL4U(E)D1/D2 CDL4U(E)D3
INDICATOR/ DIODE
CIRCUITS
35 or 32mm DIN Rail
Altech offers different types of
terminals incorporating
electronic components for
signal converting, circuit
protection and status
indication. Based on customer
requirements, specially
With arc suppression circuit for Diode circuit for
assembled terminals are contactors and solenoid valves - DC reverse polarity protection
offered.
Terminal Width 6 mm 6 mm
CDL4U(O) - Double level
terminal with open lower Height x Length 54 x 55.5 mm 54 x 55.5 mm
current bar to accommodate Terminal Voltage 300 V~ 300 V~
electronic components like
diodes, resistors, LEDs, etc. Stripping Length 9 mm 9 mm

Approvals C US C US
Diode Specifications
Wire Range 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG
Diode 1N 4007
Diode Reverse Voltage 1000 V Voltage Rating 600 V 400 V 600 V 600 V 400 V 600 V

Diode Current 1A Current Rating 25 A 32 A 35 A 25 A 32 A 35 A

Torque 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block CDL4U(E)D1 100 CDL4U(E)D3 100

CDL4U(E)D2 100

End Plate EPCDL4U 50 EPCDL4U 50

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA702 50

for ordering information CA802 50 CA802 50
refer to page 63
2 pole CA727/2 10 CA727/2 10
Internal 3 pole CA727/3 10 CA727/3 10
Jumper 4 pole CA727/4 10 CA727/4 10
10 pole CA727/10 10 CA727/10 10

2 pole CA703/1 100 CA703/1 100

Current 3 pole CA704/1 100 CA704/1 100
Bars 4 pole CA705/1 100 CA705/1 100
10 pole CA732/10 100 CA732/10 100
10 pole (breakable) CA732/10-A 100 CA732/10-A 100
100 pole CA732/100 10 CA732/100 10
Shorting Sleeve & Screw CA607/S/Q 100 CA607/S/Q 100
Marking Tags (MT Type) MT2 100 MT2 100

1 2 1 2

3 4 3 C 4

D1 D3
1 2

C
3 4

D2

38 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CDL4U(E)DD1/DD2 CDL4U(E)DD3/DD4 CDL4U(E)D4 CDL4U(E)DD5

Diode circuit for lamp testing Diode circuit for lamp testing Diode circuit for lamp testing with Diode circuit for lamp testing with
LED series resistance LED series resistance

6 mm 6 mm 6 mm 6 mm

54 x 55.5 mm 54 x 55.5 mm 54 x 55.5 mm 54 x 55.5 mm

300 V~ 300 V~ 24 V– 24 V~

9 mm 9 mm 9 mm 9 mm

C US C US C US C US

22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V 600 V 400 V 600 V 600 V 400 V 600 V 600 V 400 V 600 V

25 A 32 A 35 A 25 A 32 A 35 A 25 A 32 A 35 A 25 A 32 A 35 A

7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

CDL4U(E)DD1 100 CDL4U(E)DD3 100 CDL4U(E)D4 100 CDL4U(E)DD5 100

CDL4U(E)DD2 100 CDL4U(E)DD4 100

EPCDL4U 50 EPCDL4U 50 EPCDL4U 50 EPCDL4U 50

CA702 50 CA702 50 CA702 50 CA702 50

CA802 50 CA802 50 CA802 50 CA802 50

CA727/2 10 CA727/2 10 CA727/2 10 CA727/2 10

CA727/3 10 CA727/3 10 CA727/3 10 CA727/3 10
CA727/4 10 CA727/4 10 CA727/4 10 CA727/4 10
CA727/10 10 CA727/10 10 CA727/10 10 CA727/10 10

CA703/1 100 CA703/1 100 CA703/1 100 CA703/1 100

CA704/1 100 CA704/1 100 CA704/1 100 CA704/1 100
CA705/1 100 CA705/1 100 CA705/1 100 CA705/1 100
CA732/10 100 CA732/10 100 CA732/10 100 CA732/10 100
CA732/10-A 100 CA732/10-A 100 CA732/10-A 100 CA732/10-A 100
CA732/100 10 CA732/100 10 CA732/100 10 CA732/100 10

CA607/S/Q 100 CA607/S/Q 100 CA607/S/Q 100 CA607/S/Q 100

MT2 100 MT2 100 MT2 100 MT2 100

1 2 1 2 1 2 1 2

C C C C
C
3 C +4 +3 +4 3 +4 3 C +4

DD1 DD3 D4 DD5

1 2 1 2

C C C

3 C -4 +3 +4

DD2 DD4

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 39
 CDL4U(E)N1 CDL4U(E)LD5* CDL4U(E)LD3*

AC voltage indicator with neon lamp AC voltage indicator with LED AC/ DC voltage indicator with LED

Terminal Width 6 mm 6 mm 6 mm

Height x Length 54 x 55.5 mm 54 x 55.5 mm 54 x 55.5 mm

Terminal Voltage 100 V~ to 220 V 24 V~, 48 V~, 120V~, 220V~ 12 V~, 24 V~

Stripping Length 9 mm 9 mm 9 mm

Approvals
C US C US C US

Wire Range 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG

Voltage Rating 600 V 400 V 600 V 600 V 400 V 600 V 600 V 400 V 600 V

Current Rating 25 A 32 A 35 A 25 A 32 A 35 A 25 A 32 A 35 A

Torque 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block CDL4U(E)N1 50 CDL4U(E)LD5* 50 CDL4U(E)LD3* 50

End Plate EPCDL4U 50 EPCDL4U 50 EPCDL4U 50

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA702 50 CA702 50

for ordering information CA802 50 CA802 50 CA802 50
refer to page 63

Internal 2 pole CA727/2 10 CA727/2 10 CA727/2 10

Jumper 3 pole CA727/3 10 CA727/3 10 CA727/3 10
4 pole CA727/4 10 CA727/4 10 CA727/4 10
10 pole CA727/10 10 CA727/10 10 CA727/10 10
Current 2 pole CA703/1 100 CA703/1 100 CA703/1 100
Bars 3 pole CA704/1 100 CA704/1 100 CA704/1 100
4 pole CA705/1 100 CA705/1 100 CA705/1 100
10 pole CA732/10 100 CA732/10 100 CA732/10 100
10 pole (breakable) CA732/10-A 100 CA732/10-A 100 CA732/10-A 100
100 pole CA732/100 10 CA732/100 10 CA732/100 10

Shorting Sleeve & Screw CA607/S/Q 100 CA607/S/Q 100 CA607/S/Q 100

Marking Tags (MT Type) MT2 100 MT2 100 MT2 100

1 2 1 +1

3 4 3 C 4 +3 +4

N1 LD5 LD3

* Add required voltage to part number as a suffix

i.e. CDL4U(E)LD5/110 is for 110V.

40 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CDL4U(E)LD4* CDL4U(E)LD1/LD2 CDL4U(E)L1/L2* CDL4U(O)

AC/ DC voltage indicator with LED DC voltage indicator with LED DC voltage indicator with LED Electronic Component Carrier

6 mm 6 mm 6 mm 6 mm

54 x 55.5 mm 54 x 55.5 mm 54 x 55.5 mm 54 x 55.5 mm

24 V~ 24 V– 6 V–, 24 V–, 60 V– –

9 mm 9 mm 9 mm 9 mm

C US C US C US C US

22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V 600 V 400 V 600 V 600 V 400 V 600 V 600 V 400 V 600 V

25 A 32 A 35 A 25 A 32 A 35 A 25 A 32 A 35 A 25 A 32 A 35 A

7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

CDL4U(E)LD4* 50 CDL4U(E)LD1 50 CDL4U(E)L1* 50 CDL4U(O) 100

CDL4U(E)LD2 50 CDL4U(E)L2* 50

EPCDL4U 50 EPCDL4U 50 EPCDL4U 50 EPCDL4U 50

CA702 50 CA702 50 CA702 50 CA702 50

CA802 50 CA802 50 CA802 50 CA802 50

CA727/2 10 CA727/2 10 CA727/2 10 CA727/2 10

CA727/3 10 CA727/3 10 CA727/3 10 CA727/3 10
CA727/4 10 CA727/4 10 CA727/4 10 CA727/4 10
CA727/10 10 CA727/10 10 CA727/10 10 CA727/10 10

CA703/1 100 CA703/1 100 CA703/1 100 CA703/1 100

CA704/1 100 CA704/1 100 CA704/1 100 CA704/1 100
CA705/1 100 CA705/1 100 CA705/1 100 CA705/1 100
CA732/10 100 CA732/10 100 CA732/10 100 CA732/10 100
CA732/10-A 100 CA732/10-A 100 CA732/10-A 100 CA732/10-A 100
CA732/100 10 CA732/100 10 CA732/100 10 CA732/100 10

CA607/S/Q 100 CA607/S/Q 100 CA607/S/Q 100 CA607/S/Q 100

MT2 100 MT2 100 MT2 100 MT2 100

-1 +1 +1 1 2

C
C

+3 +4 -3 -4 -3 -4 3 4

LD4 LD1 L1
-1 -1

C
+3 +4 +3 +4

LD2 L2 * Add required voltage to part number as a suffix

i.e. CDL4U(E)LD5/110 is for 110V.

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 41
 SURGE SUPPRESSOR CDL4U(E)LA CDL4U(E)3LA
TERMINAL BLOCKS
In applications where circuit
protection against transient
overvoltage is required, Altech
Surge Suppressor Terminal
Blocks with built-in electronic
components are
recommended.
Lightning Arrestor 3 Pole Lightning Arrestor
These terminals are designed
to protect a single line against
Terminal Width 12 mm 18 mm
a longitudinal (line / earth)
surge, thereby protecting Height x Length 54 x 55.5 mm 54 x 55.5 mm
distribution and inputs.
Stripping Length 9 mm 9 mm

Insulation Material Polyamide 6.6 Polyamide 6.6

Type of Connection 4 screw clamps 4 screw clamps

Ratings

Wire Range 22-10 AWG 22-10 AWG

Voltage Rating 75, 90, 240, 600, 1000 V DC 90, 250, 350, 450 V DC

Nominal Discharge Current 20 KA (8/20 µs) 10 KA (8/20 µs)

Peak Current – –

Response Time 100 ns 100 ns

Nominal Current 10A 5A

Capacitance <1.5 pf <1.0 pf

Application For coarse line protection of For simultaneous protection of lines

measuring, distributing or data against transversal (line/line) and
communication interfaces. longitudinal (line/earth) surge.

Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block CDL4U(E)LA* 20 CDL4U(E)3LA* 20

End Plate EPCDL4U 50 EPCDL4U 50

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA702 50

for ordering information CA802 50 CA802 50
refer to page 63

Marking Tags (MT Type) MT2 100 MT2 100

* Add required voltage to part number as a suffix

i.e. CDL4U(E)LA/75 is for 75V.

42 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CDL4U(E)MOV1 CDL4U(E)SD CDL4U(E)RC

MOV Suppressor Diode RC Circuit

12 mm 12 mm 18 mm

54 x 55.5 mm 54 x 55.5 mm 54 x 55.5 mm

9 mm 9 mm 9 mm

Polyamide 6.6 Polyamide 6.6 Polyamide 6.6

4 screw clamps 4 screw clamps 4 screw clamps

22-10 AWG 22-10 AWG 22-10 AWG

130 V AC* 12-48V DC / 12-160V AC** 250 V AC / 330 V DC

– 1.5 KA (8/20 µs) 20A

2kA-6.5kA (8/20 µs) – –

<25ns 1 ns DC / 5 ns AC –

10A 10A 10A

2
100-20,000 pf – 0.1 µf or 0.22 µf

For protection from voltage For fine protection of data interfcaes, For protection of DC solenoid valves
surge, spikes sensors, contacts, etc. and contactors

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

CDL4U(E)MOV 20 CDL4U(E)SD 20 CDL4U(E)RC 10

EPCDL4U 50 EPCDL4U 50 EPCDL4U 50

CA702 50 CA702 50 CA702 50

CA802 50 CA802 50 CA802 50

MT2 100 MT2 100 MT2 100

1 A fuse block is recommended to protect MOV terminals by disconnecting the faulted varistor. See pages 28-30 for fuse blocks.
* Other voltages available upon request. Call Altech for voltage selection.
** Phase to Phase / Phase to ground. Call Altech for voltage selection.

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 43
 TAB, TERMI-POINT® CTC4U CTS4U-TM CDL4U-TM
TERMINAL BLOCKS
CTC4U Tab Connection Connection Points
terminals offer quick
connection. Connection is
achieved by pushing the
lug onto the tab blade of
the terminal block. The
terminal housing is so
designed that the wall
protrudes beyond the tab
blades.

The CTS4U-TM single level Terminal Width 6 mm 6 mm 6 mm

and the CDL4U-TM double Height x Length 49.5 x 47 mm 67 x 43 mm 84 x 55.5 mm
level terminal blocks have a
provision for clip Stripping Length 9 mm 9 mm 9 mm
connection according to
DIN 41611-4. Three wires Insulation Material Polyamide 6.6 Polyamide 6.6 Polyamide 6.6
(0.5 sq. mm) can be Type of Connection 5 tab connection points and 1 srew connection and 1 blade for 2 srew connections and 2 blades
connected with a clip onto 1 tapped hole for cross connection 3 (0.5 sq. mm) connections for 6 (0.5 sq. mm) connections
the pin using a special tool Approvals
(contact Altech for
information). These terminal
Rated Cross Section 0.5-4 sq.mm 22-12 AWG 0.5-4 sq.mm 22-12 AWG 0.5-4 sq.mm 22-12 AWG
blocks provide high wiring
density without extension Voltage Rating 250 V 300 V 250 V 300 V 250 V 300 V
of the mounting rail.
Current Rating 32 A 25 A 10 A 10 A 10 A 10 A
CTC4U is used primarily in
Tab Blade Size (mm) 6.3 x 0.8 6.3 x 0.8 0.8 x 1.6 0.8 x 1.6 0.8 x 1.6 0.8 x 1.6
railway systems. The
CTS4U-TM and the CDL4U-
TM is used mostly in the Cat No. Std. Pk. Cat No. Std. Pk. Cat No. Std. Pk.
telecommunications
industry. Terminal Block CTC4U 100 CTS4U-TM 100 CDL4U-TM 100

End Plate EPCTC4U 50 EP2.5/4UN 50 EPCDL4U 50

DIN Rail
for ordering information
refer to page 62

End Stop
for ordering information CA702 50 CA702 50 CA702 50
refer to page 63 CA802 50 CA802 50 CA802 50
Internal 2 way CA727/2 100 CA722/2 100 CA727/2 10
Jumper 3 way CA727/3 50 CA722/3 50 CA727/3 10
4 way CA727/4 50 CA722/4 50 CA727/4 10
10 way CA727/10 10 CA722/10 10 CA727/10 10
Insulated 2 way CA747/2 100 CA742/2 100 CA747/2 100
Internal 3 way CA747/3 50 CA742/3 50 CA747/ 50
Jumper 4 way CA747/4 50 CA742/4 50 CA747/ 50
10 way CA747/10 10 CA742/10 10 CA747/10 10
Current 2 way CA703/1 100 CA703/1 100 CA703/1 100
Bars 3 way CA704/1 100 CA704/1 100 CA704/1 100
4 way CA705/1 100 CA705/1 100 CA705/1 100
10 way CA732/10 100 CA732/10 100 CA732/10 100
10 pole (breakable) CA732/10-A 100 CA732/10-A 100 CA732/10-A 100
100 pole CA732/100 10 CA732/100 10 CA732/100 10
Shorting Sleeve & Screw CA607/S/Q 100 CA707/S/Q/01 100 CA607/S/Q 100
External 2 pole CA713/2 100 CA714/2 100
Jumper 3 pole CA713/3 100 CA714/3 100
4 pole CA713/4 50 CA714/4 50
10 pole CA713/10 25 CA714/10 25

Marking Tags (MT Type) MT6 100 MT6 100 MT2 100

44 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CSC2.5T CSC4T CSC6T
FEED-THROUGH
Spring Clamp
Terminals
These terminal blocks
offer a time saving
alternative to the
popular screw clamp
connection. They can be
mounted on 35 mm
DIN rails. Insulated
push-in type jumpers
offer a quick and shock Terminal Width 5 mm 6 mm 8 mm
proof solution for most
cross-connection Height x Length 36 x 58 mm 42 x 65 mm 45 x 72 mm
applications.
Stripping Length 9 mm 9 mm 12 mm

Insulation Material Polyamide 6.6 Polyamide 6.6 Polyamide 6.6

MULTI-CONNECTION
Spring Clamp Type of Connection 2 spring clamps & 2 slots for interconnection 2 spring clamps & 2 slots for interconnection 2 spring clamps & 2 slots for interconnection

Terminals Approvals
C US C US C US
Altech Multiple
Wire Range 22-14 AWG 0.5-2.5 sq.mm 22-14 AWG 22-12AWG 0.5-4 sq.mm 22-12 AWG 22-8AWG 0.5-8sq.mm 22-8AWG
connection Spring
Clamp terminals offer Voltage Rating 600 V 750 V 600 V 600 V 750 V 600 V 600 V 750 V 600 V
a reliable solution for
problems posed by Current Rating 20 A 24 A 20 A 25 A 32 A 25 A 50 A 41 A 50 A
multiple voltage
connections. The
terminal eliminates
conventional method Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.
.
of cross connection /
Terminal Block CSC2.5T 100 CSC4T 100 CSC6T 50
looping, saving
additional space. End Plate EPCSC2.5T 50 EPCSC4T 50 EPCSC6T 50
The terminals provide
of further multiplication Partition Plate PPCSC2.5T 50 PPCSC4T 50 PPCSC6T 50
connections through DIN Rail
bridging. The Multiple for ordering information
Connection Terminal refer to page 62
Blocks can even be
bridged to Standard End Stop
for ordering information
CA702 50 CA702 50 CA702 50
Feed Through Spring refer to page 63 CA802 50 CA802 50 CA802 50
Clamp Terminal Block of
Jumpers Adjacent CA801/1 100 CA801/2 100 CA801/3 100
respective wire size Alternate
(CSC2.5T / CSC4T / CA801/1-3 100 CA801/2-3 100 CA801/3-3 100
CSC6T). Push in type CA901/1 100 CA901/2 100 CA901/3 100
wire jumper

Marking Tags MT5 100 MT6 100 MT8 100

(MT Type)

50 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CSC10T CSC2.5T1-2 CSC2.5T2-2 CSC4T1-2

10 mm 5 mm 5 mm 6 mm

50 x 75 mm 36 x 74 mm 36 x 90 mm 42 x 85 mm

12 mm 9 mm 9 mm 9 mm

Polyamide 6.6 Polyamide 6.6 Polyamide 6.6 Polyamide 6.6

2 spring clamps & 2 slots for interconnection 3 spring clamps & 2 slots for interconnection 4 spring clamps & 2 slots for interconnection 3 spring clamps & 2 slots for interconnection

* *
C US C US C US C US

16-6 AWG 1.5-10 sq.mm. 16-6AWG 22-14 AWG 0.5-2.5 sq.mm. 22-14 AWG 22-14 AWG 0.5-2.5 sq.mm. 22-14 AWG 22-12 AWG 0.5-4 sq.mm. 22-12 AWG

600 V 800 V 600 V 600V 750 V 600 V 600V 750 V 600 V 600V 750 V 600 V

65 A 57 A 65 A 20A 24 A 20 A 20A 24 A 20 A 25A 32 A 25 A

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

CSC10T 100 CSC2.5T1-2 100 CSC2.5T2-2 50 CSC4T1-2 50

EPCSC10T 50 EPCSC2.5T1-2 50 EPCSC2.5T2-2 50 EPCSC4T1-2 50

CA702 50 CA702 50 CA702 50 CA702 50

CA802 50 CA802 50 CA802 50 CA802 50

CA801/4 100 CA801/1 100 CA801/1 100 CA801/2 100

CA801/1-3 100 CA801/1-3 100 CA801/2-3 100

CA901/1 100 CA901/1 100 CA901/2 100

MT10 100 MT5 100 MT5 100 MT6 100

*UL& CSA pending.

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 51
 CSC4T2-2 CSC6T1-2 ADL2.5

Terminal Width
6 mm 8 mm 5 mm
Height x Length
42 x 105 mm 45 x 94 mm 50 x 79.5 mm
Stripping Length
9 mm 12 mm 9 mm
Insulation Material
Polyamide 6.6 Polyamide 6.6 Polyamide 6.6
Type of Connection
4 spring clamps & 2 slots for interconnection 3 spring clamps & 2 slots for interconnection 4 spring clamps & 4 slots for interconnection
Approvals * * * *
C US C US C US
Wire Range
22-12 AWG 0.5-4 sq.mm. 22-12 AWG 22-8 AWG 0.5-6 sq.mm. 22-8 AWG 22-14 AWG 2.5 sq.mm. 22-14 AWG
Voltage Rating
600 V 750 V 600 V 600 V 800 V 600 V 600 V 500 V 600 V
Current Rating
25 A 32 A 25 A 50 A 41 A 50 A 20 A 24 A 20 A

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block CSC4T2-2 50 CSC6T1-2 50 ADL2.5 50

End Plate EPCSC4T2-2 50 EPCSC6T1-2 50 EPADL2.5 50

DIN Rail
for ordering information
refer to page 62

End Stop
for ordering information
CA702 50 CA702 50 CA702 50
refer to page 63 CA802 50 CA802 50 CA802 50

Jumpers Adjacent CA801/2 100 CA801/3 100 CA801/1 100

Alternate CA801/2-3 100 CA801/3-3 100 CA801/1-3 100

Push in type CA901/2 100 CA901/3 100 CA901/1 100

wire jumper

Marking Tags MT6 100 MT8 100 MT5 100

(MT Type)

*UL & CSA pending.

52 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 ASF4 ASF4(L)*
Spring Clamp Fuse
Terminal Blocks
Altech offers ‘Screwless’ Spring
Clamp Fuse Terminal Blocks.
The terminal has a moving type
hinged carrier that has specially
designed space for cartridge
type glass fuse of size Ø 5 x 20
or Ø 5 x 25 mm. The fuse can
be engaged or disengaged by
the movement of the carrier.
Terminal Width 8 mm 8 mm
Cross connection is possible
with specially designed push-in Height x Length 60 x 80 mm 60 x 80 mm
type jumpers.
Stripping Length 9 mm 9 mm

Insulation Material Polyamide 6.6 Polyamide 6.6

Type of Connection 2 spring clamps & 2 slots for interconnection 2 spring clamps & 2 slots for interconnection

Tyoe of fuse used Ø5x20, Ø5x25mm Ø5x20, Ø5x25mm

Fusion Voltage 24V AC/DC, 48V AC/DC

110V AC/DC, 220V AC
1 1 1 1
Approvals
C US C US

Wire Range 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG

Voltage Rating 600 V 500 V 600 V 600 V 500 V 600 V

Current Rating 8A 6.3 A 8A 8A 6.3 A 8A

Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block ASF4 100 ASF4(L)* 100

End Plate EPASF4 50 EPASF4 50

DIN Rail
for ordering information
refer to page 62

End Stop CA702 50 CA702 50

for ordering information CA802 50 CA802 50
refer to page 63
Insulated Jumper CA801/7 100 CA801/7 100
(2 pole)

Marking Tags
(MT Type) MT8 100 MT8 100

1
UL & CSA pending.
* Add required voltage to part number as a suffix. i.e. ASF4(L)/24 for 24V AC/DC.

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 53
 CSCG2.5T CSCG4T
Spring Clamp Ground (Earth)
Terminal Blocks
Altech offers ‘Screwless’ Spring
Clamp Ground Terminal Blocks.
Specially designed alloy feet
helps inachieving very low
contact resistance and vibration
proof grounding.
CSCG series terminals can be
mounted on Din 35 rail along
with other terminal blocks of
CSC series. The terminal block Terminal Width 5 mm 6 mm
profile matches with that of CSC
Height x Length 36 x 58 mm 42 x 65 mm
terminal block of same wire size.
Special features of CSCG Stripping Length 9 mm 9 mm
terminal blocks are:
Insulation Material Polyamide 6.6 Polyamide 6.6
• Vibration proof grounding
Type of Connection 2 spring clamp connection, 2 spring clamp connection,
• Very low contact resistance grounding through alloy feet grounding through alloy feet
because of special alloy feet
* *
Approvals
• Drop-on grounding connection C US C US

• Spring clamp to accept solid Wire Range 22-14 AWG 0.5-2.5 sq.mm 22-14 AWG 22-12 AWG 0.5-4 sq.mm 22-12 AWG
and stranded wire
Voltage Rating 800 V 800 V

Current Rating 24 A 32 A

Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block CSCG2.5T 100 CSCG4T 100

DIN Rail
for ordering information
refer to page 62

Marking Tags
(MT Type) MT5 100 MT6 100

*UL & CSA pending.

54 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 CSCG6T CSCG10T

Terminal Width 8 mm 10 mm

Height x Length 45 x 72 mm 50 x 75 mm

Stripping Length 12 mm 12 mm

Insulation Material Polyamide 6.6 Polyamide 6.6

Type of Connection 2 spring clamp connection, 2 spring clamp connection,

grounding through alloy feet grounding through alloy feet
* * * *
Approvals C US C US

Wire Range 22-8 AWG 0.5-6 sq.mm 22-8 AWG 16-6 AWG 0.5-10 sq.mm 16-6 AWG

Voltage Rating 800 V 800 V

Current Rating 41 A 57 A

Cat. No. Std. Pk. Cat. No. Std. Pk.

Terminal Block CSCG6T 50 CSCG10T 50

DIN Rail
for ordering information
refer to page 62

Marking Tags
(MT Type) MT8 100 MT10 100

*UL & CSA pending.

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 55
 CSCP2.5T CSCP2.5T2
PANEL MOUNT SPRING
CLAMP TERMINALS

Altech “screwless”
spring clamp panel
mount terminal blocks
are an excellent solution
for extremely compact
wiring applications.
These terminal blocks are
“add-on” type and can
be combined to form
multi-pole assemblies. Terminal Width 5 mm 10 mm
The stacked assembly is
Height x Length 27 x 35 mm 27 x 35 mm
fitted with mounting end
sections on both ends for Stripping Length 9 mm 9 mm
easy installation on to
the panel. Insulation Material Polyamide 6.6 Polyamide 6.6
The terminal has marker 2 spring clamp connections 4 common spring clamp connections
Type of Connection
holding recessess on
three sides to accept Approvals
marking tags. Cross C US C US

connection can be Wire Range 22-14 AWG 0.5-2.5 sq.mm 22-14 AWG 22-14 AWG 0.5-2.5 sq.mm 22-14 AWG
achieved with the aid of
insulated jumpers. Voltage Rating 600 V 750 V 600 V 600 V 750 V 600 V

The CSCP2.5T2 panel Current Rating 20 A 24 A 20 A 20 A 24 A 20 A

mount terminal blocks
have two connection
points on each side all
with the same potential. Cat. No. Std. Pk. Cat. No. Std. Pk.
The terminals provide CSCP2.5T 100 CSCP2.5T2 100
Terminal Block
possibility of further
multiplication through End Section EPCSCP2.5T 50 EPCSCP2.5T 50
jumpering. (set of left and right)

Insulated Jumper CA803/1 100 CA803/1 100

(2 pole)

Operating Tool SCA2-5 1 SCA2-5 1

Marking Tags MT4 100 MT3 100

(MT Type)

EPCSCP2.5T CSCP2.5T2

EPCSCP2.5T

CSCP2.5T

56 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
 Custom
Assemblies
Available
• Most competitive in industry
• Made to your specifications
• Large inventory of parts
• Variety of colors available
• Shipped in 2-3 weeks

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 57