Scribd
Upload
132 views1 page

1127 Man

1. The document provides instructions for installing batteries in a remote control transmitter and receiver, programming the receiver to the transmitter, and using the basic on/off functions. 2. It explains that the receiver plugs into a wall socket, and the transmitter uses two button cell batteries, which are installed by removing the cover on the back of the transmitter. 3. The receiver is programmed to the transmitter by pressing the learn button on the receiver while simultaneously pressing a channel button on the transmitter, and this can be repeated for additional receivers.

Uploaded by

Ahmad Faris
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
132 views1 page

1127 Man

1. The document provides instructions for installing batteries in a remote control transmitter and receiver, programming the receiver to the transmitter, and using the basic on/off functions. 2. It explains that the receiver plugs into a wall socket, and the transmitter uses two button cell batteries, which are installed by removing the cover on the back of the transmitter. 3. The receiver is programmed to the transmitter by pressing the learn button on the receiver while simultaneously pressing a channel button on the transmitter, and this can be repeated for additional receivers.

Uploaded by

Ahmad Faris
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

RC270+TR430 GETTING STARTED battery installation LEARN FUNCTION TROUBLESHOOTING

Indoor Remote Control Set


Batteries are not required in the
RC270 receiver. Two button cell
3 1 Plug receiver into wall socket LEARN
ON/OFF problem solution
OWNERS batteries are included for the TR430
2 Press LEARN on receiver while Transmitter stops turning Use the LEARN function to
transmitter 2 4 receiver on and off. reprogram the receiver
MANUAL simultaneously pressing the desired
Congratulations on your ON/OFF 1 remove the battery cover from 2 channel button on the transmitter or
Check the battery
the back of the transmitter Repeat 1 and 2 for any additional
purchase of a UPM
remote control set. Please
LEARN
3 receivers (available at your local
take the time to read and place two button cell batteries
understand this manual so 2 between terminals observing retailer)
you can begin to enjoy the
convenience this product proper polarity then replace cover 1 4 If LEARN is completed successfully,
3 FCC COMPLIANCE
can offer. the LED on the receiver should light This device complies with Part 15 of the FCC Rules of Operation and is
the green LED will light up
FEATURES 3 with any key press once the
up when ON is pressed subjected to the following two conditions:
battery is installed correctly
! 433 MHz RF technology 1. this device may not cause harmful interference, and
! Control up to 4 remote button descriptions ON/OFF FUNCTION 2. this device must accept any interference received,
receivers ON/OFF including interference that may cause undesired operation.
! ON/OFF function ON/OFF LEARN
ON/OFF
LED Indicator 2
1 Power On/Off by using the ON/OFF
LEARN

! 15A / 1800W resistive LEARN - used when


! Transmission range of CH 1 ON CH 1 OFF keys on the transmitter
programming receiver
up to 130 feet in open
area channel
CH 2 ON CH 2 OFF
2 The ON/OFF button on the receiver TECHNICAL SPECIFICATIONS
CH 3 ON CH 3 OFF also turns power on and off 1
CH 4 OFF Ratings: 120 V AC
CH 4 ON
ALL OFF If you have more than one receiver set up, Maximum Load: 1800W resistive; 600W tungsten
ALL ON
* you can use the ALL ON or ALL OFF Transmission Range: up to 130 feet in open area
Receiver Transmitter button to simultaneously turn ALL the * Transmission Frequency: 433.92 MHz
receivers ON or OFF.

You might also like