A

Report On

MAGNETO OPTIC CURRENT TRANSDUCER

DEPARTMENT OF ELECTRICAL ENGINEERING

COLLEGE OF TECHNOLOGY & ENGINEERING
(Maharana Pratap University of Agriculture and Technology)
Udaipur (Rajasthan)

SUBMITTED TO: SUBMITTED BY:

Mr. R.R. Joshi Hemendra singh gaur
Prof. and H.O.D.(Electrical Dept) B.E. IV YEAR
C.T.A.E. UDAIPUR Electrical Engg.

1
 INTRODUCTION

An accurate electric current transducer is a key component of

any power system instrumentation. To measure currents power stations

and substations conventionally employ inductive type current

transformers with core and windings. For high voltage applications,

porcelain insulators and oil-impregnated materials have to be used to

produce insulation between the primary bus and the secondary

windings. The insulation structure has to be designed carefully to

avoid electric field stresses, which could eventually cause insulation

breakdown. The electric current path of the primary bus has to be

designed properly to minimize the mechanical forces on the primary

conductors for through faults. The reliability of conventional high-

voltage current transformers have been questioned because of their

violent destructive failures which caused fires and impact damage to

adjacent apparatus in the switchyards, electric damage to relays, and

power service disruptions.

2
 MOCT-PRINCIPLE

The Magneto-Optical current transformer is based on the

Faradays effect. Michael Faraday discovered that the orientation of

linearly polarized light was rotated under the influence of the magnetic

field when the light propagated in a piece of glass, and the rotation

angle was proportional to the intensity of the magnetic field. The

concept of Faraday Effect could be understood from the Fig.1.

Fig. 1

Generally, this phenomenon can be described as follows:

θ = V ∫Β. dl …………Eq(1)

‘θ ’ is the Faraday rotation angle,

3
‘V’ is the Verdet constant of magneto-optical material

‘B’ is the magnetic flux density along the optical path

‘l’ is the optical path

When the linearly polarized light encircles a current carrying

conductor eq(1) can be rewritten as according to Ampere’s law as

θ =nµ VI ………….Eq(2)

‘I ‘is the current to be measured,

‘µ ’ is the permeability of the material,

‘n’ is the number of turns of the optical path.

The Faraday effect outlined in eq(2) is a better format to

apply to an MOCT, because the rotation angle in this case is directly

related to the enclosed electric current. It rejects the magnetic field

signals due to external currents which are normally quite strong in

power system.

4
 Fig. 2

The typical application of the Faraday effect to an MOCT is

clear from fig(2). A polarizer is used to convert the randomly polarized

incident light into linearly polarized light. The orientation of the

linearly polarized light rotates an angle θ after the light has passed

through the magneto-optical material because of Faraday Effect. Then

0
another polarization prism is used as an analyzer, which is 45

oriented with the polarizer, to convert the orientation variation of the

polarized light into intensity variation of the light with two outputs,

and then these two outputs are send to photo detectors. The purpose of

using the analyzer is that photo detectors can only detect the intensity

of light, rather than the orientation of polarizations. The output optical

signals from the analyzer can be described as,

5
 P1 = P 0
(1 + Sin 2θ )
2

P2 = P 0
(1 - Sin 2θ )
2

P0 is the optical power from the light source,

θ is the Faraday rotation angle,

P1 and P2 are the optical power delivered by the detectors.

In order to properly apply Eq(2) in the MOCT design by

making the optical path wrap around the current carrying conductor,

the optical path has to be folded by reflections. Total internal

reflections and metal reflections are good ways to achieve this.

However reflections introduce phase shift; hence change the

polarization state of the light. The optical prism has to be designed to

keep the light going through the MOCT linearly polarized. In order to

stimulate the behavior of the polarized light reflect through the glass

prism of an MOCT, ie to maintain the light traveling through the glass

prism to be linearly polarized and also for the analysis of the effects of

dielectric and metal reflections on the linearly polarized light, a

computer programme is written in FORTARN language. Stimulation

results include information such as polarization state change at each

reflection and the overall responsibility of the optical sensor.

6
 DESIGN

Fig. 3

Fig (3) shows the structure of this MOCT. The optical sensor

consists of two separate clamp-on parts. In each part of the device,

linearly polarized light is arranged to pass through the optical glass

prism to pickup the Faraday rotation signal. The polarization

7
compensation technique is applied at each corner of the prisms, so that

the light passing through the prism remains linearly polarized. At the

other end of the prism, a silver mirror reflects the light beam so that

light beam comes back to its sending end via the same route while

accumulating the Faraday rotations.

Fig. 4

The two halves can be assembled around the conductor.

Thereby, the rotation angles from the two halves of the sensor

[Fig.4(a)] are added up in the signal processing unit so that the total

rotation angle (θ 1+θ 2 ) is the same as the rotation angle θ from the

optical path shown in Fig4(b), which is two turns around the

conductor.

8
 Fig. 5

Fig. 5 shows the structure of the housing for the clamp-on

MOCT. The optical glass prism polarizes, and lenses are completely

sealed in the housing by epoxy, so that they are free of environmental

hazards such as dust and moisture. This structure avoids the use of

magnetic material to concentrate the magnetic field as found in some

other MOCT design and Hall Effect current measurement devices.

There for it is free from the effect of remanent flux, which could affect

the accuracy of the current measurement.

9
 MAGNETO-OPTICAL SENSOR

Almost all transparent material exhibits the magneto-optical effect or Faraday

Effect, but the effect of some of the material is very temperature dependent, and they are
not suitable for the sensing material. The optical glasses are good candidate for the
sensing material, because the Verdet constants are not sensitive to the temperature
changes, and they have good transparency properties. They are cheep and it is easy to
get large pieces of them. Among the optical glasses SF-57 is the best choice, as it has
larger Verdet constant than most of the other optical glasses. And MOCT made out of
these materials can achieve higher sensitivity. In the MOCT, from Eq (2), the total
internal rotation angle is,

θ ≈ θ 1+ θ 2 ≈ 2µ VI

Where I is the current to be measured,

µ = 4π x 10-7 H/m

V=7.7 x 102 degrees/Tm at a wavelength of 820nm

Therefore θ = 1.9 degrees/ KA.

Different optical fibers are designed for different usage. The

single mode fiber has very wide bandwidth, which is essential for

communication systems, but it is difficult to launch optical power into

the single mode fiber because of it’s very thin size. While large

multimode fiber is convenient for collecting maximum amount of light

from the light source, it suffers from the problem of dispersion which

limits its bandwidth. In the situation of power system instrumentation,

only moderate frequency response is required and in MOCT, the more

optical power received by the detectors the better signal to noise ratio

10
can be achieved. Therefore, the large core multi-mode optical fiber is

used here to transfer the optical signals to and from the optical sensors.

11
 ELECRONIC CIRCUIT FOR THE MOCT

Fig. 6

Fig. 6 shows the schematic diagram of the electronic circuit

for the clamp-on MOCT. In order to make use of the dynamic range of

the digital system as well as the different frequency response

requirements of metering and relaying, metering signal (small signal)

and relaying signal (large signal) are treated differently. Two output

stages have been designed accordingly. One stage, which has 1 KA

dynamic range, is for power system current metering, and other stage,

12
which operate up to 20 KA, provides power system current signals for

digital relay systems.

In each part of the device, the sum of the two receiving

channels signals, which have the same DC bias α I0, differenced at

junction with a reference voltage Vref from the power level adjustment

potentiometer. Then an integrator is used to adjust the LED driver

current to maintain 2α I0 to be the same as the Vref at the junction.

Because the reference voltage Vref is the same for both the sides, the

DC bias α I0 and the sensitivities 2α I0 of the two halves of the

clamp-on MOCT are considered to be stable and identical.

The difference of the two receiving channels signals 2α I0

(2Sinθ 1) and 2α I0 (2Sinθ 2) in each part of the device are added

directly and then fed through an amplifier for the small signals. At the

same time these two signals are processed digitally to do a sin-1

calculation on each and then summed together for the large signal

situation when the non-linearity of the MOCT can no longer be

ignored. The ratio responses of the two output stages of the clamp-on

MOCT are designed as 10V/KA and 0.5V/KA and frequency

responses are 4KHZ and 40 KHZ respectively.

13
 APPLICATION

The MOCT is designed to operate in a transparent manner

with modern electronic meters and digital relays, which have been

adopted for a low energy analog signal interface. Typically, the design

approach is to redefine the interface point as to input the analog to

digital conversion function used by each of these measurement

systems.

14
 ADVANTAGES OF MOCT

1. No risk of fires and explosions.

2. No need to use metallic wires to transfer the signal and so simpler

insulation structure than conventional current transformer.

3. High immunity to electromagnetic interference.

4. Wide frequency response and larger dynamic range.

5. Low voltage outputs which are compatible with the inputs of digital

to analog converters.

DISADVANTAGES OF MOCT

1. Temperature and stress induced linear birefringence in the

sensing material causes error and instability.

2. The accuracy of MOCT is so far insufficient for the use in power

systems.

15
 CONCLUSION

This paper presents a new kind of current transducer known

as magneto optical current transducer. This magneto optical current

transducer eliminates many of the drawbacks of the conventional

current transformers. In an conventional current transformers, there is

a chance of saturation of magnetic field under high current,

complicated insulation and cooling structure, a chance of electro

magnetic interference etc.

By applying Faraday’s principle this transducer provides an

easier and more accurate way of current measurement. This MOCT is

widely used in power systems and substations nowadays. And a new

trend is being introduced, which known as OCP based on adaptive

theory, which make use of accuracy in the steady state of the

conventional current transformer and the MOCT with no saturation

under fault current transients.

16
 REFRENCES

• Farnoosh Rahmatian ;patric p. chavez &Nicholas A.F

“optical voltage transducers using multiple electric field
sensors”. IEEE transactions on power delivery ,vol.17 april
2002

• J C Santos ,M.C Taplama Ciogle and K Hidak

“Pockel’s High Voltage Measurement Systems” IEEE
transactions on power delivery ,vol.15 jan 2000

• http://www.iop.org/EJ/article

• http://www.cris-inst.com/publication/bejing

• Physics for engineers by Premlet

17
 ABSTRACT

An accurate current transducer is a key component of any

power system instrumentation. To measure currents, power stations

and substations conventionally employ inductive type current

transformers. With short circuit capabilities of power system getting

larger and the voltage level going higher the conventional current

transducers becomes more bulky and costly.

It appears that newly emerged MOCT technology provides a

solution for many of the problems by the conventional current

transformers. MOCT measures the rotation angle of the plane

polarized lights caused by the magnetic field and convert it into a

signal of few volts proportional to the magnetic field.

Main advantage of an MOCT is that there is no need to break

the conductor to enclose the optical path in the current carrying circuit

and there is no electromagnetic interference.

18
 CONTENTS

1. INTRODUCTION 1

2. MOCT-PRINCIPLE 4

3. DESIGN 8

4. MAGNETO-OPTICAL SENSOR 11

5. ELECRONIC CIRCUIT FOR THE MOCT 13

6. APPLICATION 15

7. ADVANTAGES OF MOCT 16

8. DISADVANTAGES OF MOCT 16

9. CONCLUSION 17

10. BIBLIOGRAPHY 18

19
 ACKNOWLEDGEMENT

I extend my sincere gratitude towards Prof. P.Sukumaran Head

of Department for giving us his invaluable knowledge and wonderful

technical guidance

I express my thanks to Mr. Muhammed Kutty our group tutor

and also to our staff advisor Ms. Biji Paul for their kind co-operation and

guidance for preparing and presenting this seminar.

I also thank all the other faculty members of AEI department and

my friends for their help and support.

20