AN211

SENSOR PRODUCTS

APPLICATION NOTE

APPLICATIONS OF MAGNETIC POSITION SENSORS

ABSTRACT except for a small offset voltage due to manufacturing
tolerances on the AMR elements. With the AMR
Magnetic position sensing using Anisotropic Magneto- elements connected in this fashion to form the
Resistive (AMR) sensors is becoming a popular wheatstone bridge, these side contacts will produce a
method of implementing a non-contacting location of differential voltage (DV) as a function of the supply
motional objects. By affixing a magnet or sensor voltage, MR ratio, and the angle theta (q); which is the
element to a angular or linear moving object with its angle between the element current flow and element
complementary sensor or magnet stationary, the magnetization (M). Figure 2 depicts this sensor bridge.
relative direction of the resulting magnetic field can be
quantified electronically. By utilizing multiple sensors Applied Field Direction
or magnets, the capability of extended angular or
linear position measurements can be enhanced. This M I I M
application note explains the principles of AMR
sensors for positional measurements, and includes R+DR R-DR
several real-life circuit applications to solve +
DV
engineering problems. VS
+ -
I M M I -
PRINCIPLES OF AMR SENSORS

Anisotropic Magnetoresistance occurs in certain R-DR R+DR

ferrous materials and can be applied as a thin strip to
become a resistive element. Honeywell uses a ferrous
material called Permalloy and forms four resistive
elements to become a wheatstone bridge sensor. Figure 2
Each magneto-resistive strip element possesses an AMR Bridge
2
ability to change resistance in a cos q relationship
where q (theta) is the angle between the magnetic To have the element magnetization direction to align
moment (M) vector and the current flow (I). Figure 1 with an externally applied magnetic field, the applied
shows the Permalloy element with field and current field must “saturate” the permalloy material. As
applied. opposed to other AMR sensor elements that operate in
Metal Contact Permalloy a linear mode, position sensing is a saturation mode
Thin Film
(NiFe)
function; meaning that the external magnetic field
M
completely re-orients the material’s magnetization. For
Current Flow q Honeywell’s magnetic position sensors, a minimum of
I
an 80 gauss magnetic field must be applied at the
bridge for the specified performance characteristics to
be met. Fields less than 80 gauss will show some
bridge operation, but the saturation may not be
Applied Field
complete enough to be relied upon.
Figure 1
AMR Element OUTPUT SIGNALS

To create the sensor from the AMR elements, the four The HMC1501 and HMC1512 are Honeywell’s AMR
elements are oriented in a diamond shape with the based magnetic position sensors that contain AMR
ends connected together by metalization to form the sensor bridges to be used in saturation mode. The
wheatstone bridge. Arbitrarily, the top and bottom HMC1501 contains one AMR bridge for a ±45° range
connections of the four identical elements are given a of position sensing, and the HMC1512 contains two
Direct Current (DC) stimulus in the form of a supply AMR bridges for a ±90° range of position sensing. The
voltage (Vs), with the remaining side connections to be bridge differential output voltage (DV) for the
measured. With no magnetic field supplied (0 gauss), HMC1501 is:
the side contacts should be at the same voltage,

Solid State Electronics Center • www.magneticsensors.com • (800) 323-8295 • Page 1

AN211
SENSOR PRODUCTS
DV = -Vs S sin (2q) where: output signal via signal conditioning circuitry. In the
digital solution, the digitized value of the output signal
Vs = Supply Voltage (volts) can be combined with an error correction value.
S = Material Constant (12mV/V)
q = Reference to Magnetic Field Angle Another common error to be accounted for is the drift
(degrees) in the material constant versus temperature. This error
effects both the bridge sensitivity and offset.
With the bridges on the HMC1512 oriented 45° in Coefficients of temperature (tempcos) of the sensitivity
rotation from each other, the differential output voltage and offset are nominally –0.32%/°C and –0.01%/°C
for sensor bridge A is: respectively. If your application should have a large
operating temperature range, consider some
DVA = Vs S sin (2q) temperature monitoring circuitry to produce error
corrections to offset the temperature drift.
And for sensor bridge B, the differential output voltage
is: If you use multiple bridge sensors, another error that
should be compensated for is the part-to-part
DVB = -Vs S cos (2q) tolerance in material constant. This manifests itself as
a change in sensitivity , resulting in varying peak-to-
Using the HMC1512 bridge A signal output plotted peak voltage swings in the DV versus theta plots.
versus theta, figure 3 depicts the two-cycle waveform. Much like the offset error voltage, analog signal
processing or digitized value corrections can be
80 implemented to counter this sensitivity tolerance.
HMC1512
Vs = 5 volts
60
DV Signal Output (millivolts)

POSITION SENSING
40
For simple magnetic position sensing, the HMC1501
20 sensor can used to detect the relative motion of a
Offset nearby magnet in linear or angular displacement.
0 Figure 4 shows a typical orientation.
-20 Ref
M
-40 Q

Peak to Peak Value

-60
-180 -90 0 90 180
theta (degrees)
Figure 3 HMC1501
Two Cycle Waveform

As you can see above, the most linear range for this
N
sensor bridge is in the ±45° range about the –180, -90, S
0, 90, and 180 degree points. Of these the 0 and ±180 moving magnet
points have a positive slope, and the ±90 points have Figure 4
a negative slope. These slopes can be taken to full Position Sensing
advantage for angular and linear positioning
applications. With the orientation of the stationary HMC1501, the
magnet can translate to ±45° and stay within a linear
Now that we have a fairly accurate method for slope of DV versus q for position sensing. Given a
magnetic field direction sensing established, it should typical supply voltage of 5 volts (Vs = +5Vdc), the
noted that some errors should be adjusted to enhance HMC1501 will provide about a 120 millivolt swing (± 60
the accuracies of the measurements. The first one is millivolts) on 2.5 volt bias voltage. The reason for the
the offset error voltage as depicted in figure 3 and 2.5 volts is that with the wheatstone bridge supply
mentioned earlier as a byproduct of manufacturing voltages at 0 and +5 volts, the bridge performs a rail
tolerances. To compensate for the offset, either analog splitter function to create two near +2.5 volt sources
signal processing or digital value corrections can be driven apart by DV as created by the magnetic field
used. In the analog signal processing solution, an and the offset error voltage. Figure 5 shows this
opposing error voltage can be summed into the bridge transfer curve.

Solid State Electronics Center • www.magneticsensors.com • (800) 323-8295 • Page 2

AN211
SENSOR PRODUCTS
voltage so that the amplifier output voltage remains at
80
HMC1501
2.5 volts at each 90° rotation in field direction. This can
Vs = 5 volts be done using a trimming potentiometer (trimmer pot)
60
DV Signal Output (millivolts)

with the wiper to Vref and the end positions of the

40 potentiometer towards each supply rail. Figure 7
shows this method.
20
Offset
U1
0 Vbridge .01mf
Vcc 249k
5.0v
10.0k
-20 OUT-
-
TLC072 output
OUT+ +
-40 Linear 10.0k U2
Range
Gnd2
Peak to Peak Value
-60 249k
Gnd1 HMC1501
-180 -90 0 90 180 Offset trim
Vcc
theta (degrees)
1k 1k 1k
Figure 5
Transfer Curve Figure 7
Offset Trimming

To interface with output pins of the HMC1501 (OUT+, Another method of offset error voltage compensation
OUT-), an instrumentation amplifier circuit is typically is to just measure it at production test and subtract that
used. Instrumentation amplifiers can be purchased as value from all future measurements. The advantages
complete integrated circuits, or constructed via of this method is that the circuit component count
combinations of discrete components and integrated remains minimal (like figure 6), and no trimming
circuits; such as operational amplifiers (op-amps). The procedure is required. The disadvantage is that you
purpose of an instrumentation amplifier is to derive the may have to reduce the amplifier gain to
difference signal (OUT+ minus OUT-), and to provide accommodate all the error buildup in offset and
additional signal amplification as desired. Figure 6 sensitivity tolerances, plus tempco changes that are all
shows a typical instrumentation amplifier circuit using multiplied by the amplifier gain.
an op-amp with external discrete components.
WIDER POSITION SENSING
U1
Vbridge .01mf
Vcc 249k
5.0v
10.0k To go from ±45° to ±90° requires two HMC1501
OUT-
-
TLC072 output sensors or a single HMC1512 dual sensor part. By
OUT+
10.0k
+
U2
using two bridges with 45° displacement from each
Gnd2 other, the two linear slopes can be used additively.
Gnd1 HMC1501
249k Figure 8 shows a typical configuration.
Vref ~ Vcc/2

From Figure 8, as the shaft rotates around, magnetic

Figure 6 flux from a magnet placed at the end of the shaft exits
Instrumentation Amplifier the north pole and returns to the south pole. With a
HMC1512 placed on the shaft axis, just above the
With a nominal 120 milli-volts peak-to-peak signal magnet, the flux passing through the sensor bridges
swing at the bridge outputs, the above circuit will retain the orientation of the magnet. From this
schematic shows an instrumentation amplifier with a rotation, the output of the two bridges will create sine
voltage gain of about 25. This will permit an output and cosine waveforms as shown in Figure 9.
voltage swing of about 3 volts peak-to-peak centered
up on about 2.5 volts (1 to 4 volts). Since the bridge
offset specification is ±7mV/V, a 5 volt supply applied
to the bridge yields ±35mV. After the instrumentation
amplifier gain, this offset is ±850mV which will stay
within the power supply rails when combined with the
amplified signal.

One method of countering the offset error voltage at

the bridge is to change the value of Vref at the
instrumentation amplifier from 2.5 volts to a nearby

Solid State Electronics Center • www.magneticsensors.com • (800) 323-8295 • Page 3

AN211
SENSOR PRODUCTS
Because most trigonometric functions are performed
as memory maps in microcontroller integrated circuits,
MAGNET
these kinds of special case conditions are easily dealt
with. The resultant angle theta (q) is the relative
position of the magnetic field with respect to the
sensor. It should be noted that if rotation is permitted

S
SHAFT beyond ±90°, the theta calculation will replicate again
Rotation N
N with postive and negative 90° readings jumping at the
end points. Further performance to 360° or ±180° can
HMC1512
be mapped into a microcontroller by using this circuit
plus a Hall Effect sensor to determine which side of
the shaft is being positionally measured via magnetic
Figure 8
polarity detection. Figure 10 shows the basic circuit
Wide Position Sensing
interface for the HMC1512.

Sensor A: V = A*sin (2*theta) + offset U1

Sensor B: V = A*cos (2*theta) + offset Vcc
Vbridge A .01mf
249k
5.0v
80 10.0k
Sensor A OUT-
- TLC072
Sensor B AN0
+
60 OUT+
10.0k U2
DV Signal Output (millivolts)

Gnd A PIC12CE674
40 249k Microcontroller

Vref ~ Vcc/2
U3
20
U1
Vbridge B .01mf
Vcc 249k
5.0v
0 10.0k
OUT-
- TLC072
AN1
-20 OUT+ +
10.0k U2
Gnd B
-40 249k
HMC1512
Vref ~ Vcc/2
-60
-180 -90 -45 0 45 90 180 Figure 10
theta (degrees) HMC1512 Circuit
Figure 9
Sine, Cosine Waveforms LINEAR DISPLACEMENT SENSING

Because the sine (sensor bridge A) and cosine For extended length linear position sensing, multiple
(sensor bridge B) will match after the offset error sensor bridges can be lined up next to a traveling
voltages are subtracted, the ratio of bridge A to bridge magnet sliding past the bridges. For best resolution
B creates a tangent 2q function and the amplitude A and linearity, the ±45° range should be backed down a
values cancel. Thus the angle theta (q) is described bit to around ±30°. As part calculating how many
as: linearly arrayed bridges are needed for fixed amount
travel (displacement), the magnet to bridge standoff
q = 0.5 * arctan (DVa / DVb) distance should be determined. For common magnets
like ceramic and AlNiCo types with under a kilo-gauss
However because there are some trigonometric of magnetic field strength at the pole face, a maximum
nuances with the arctangent function when q gets of about 0.25 inches of standoff distance will be
close to ±45° and beyond, these special cases apply: reasonable; so that the nearest two to three bridges
will be in saturation (>80 gauss) from the magnet. For
For DVa = 0, q = 0° rare earth magnets, such as Neo-dymium types, with
pole face fields around 3 kilo-gauss or more; a
For DVb = 0 and DVa = <0, q = -45° standoff distance of 0.5” can be achieved. Figure 11
shows a typical array of four HMC1501 single bridge
For DVb = 0 and DVa = >0, q = +45° sensors with nominal magnet displacement ranges.

For DVa < 0 and DVb < 0, subtract 90° from q From Figure 11, a single bridge sensor produces a DV
versus position in a linear position arrangement. This
For DVa > 0 and DVb < 0, add 90° from q will create a waveform much like figures 3 and 5
except that the end points of displacement fall away

Solid State Electronics Center • www.magneticsensors.com • (800) 323-8295 • Page 4

 DV Signal Output (millivolts)
AN211
SENSOR PRODUCTS
from the sinusoidal pattern if the magnetic field will or more positive slope values; and that will be the
continue to maintain saturation levels at the bridges. If linear range value to be used. Figure 13 depicts the
the levels fall away from saturation quickly, distant combined bridge waveforms plotted with the magnet
bridge DV’s may still be left near the peaks of the approximately centered up on the second bridge
sinusoidal pattern until the magnet travel returns to re- sensor.
saturate the bridges. Figure 12 depicts this linear 60
displacement waveform for a single sensor.
HMC1501
40 Vs = 5 volts

DV Signal Output (millivolts)

0.5” Travel

S 20
NdFeB
N 0
S 0.5”
Standoff -20
AlNiCo N
0.25”
-40
Sensor#1
Sensor#2
-60 Sensor#3
0.5” Spacing Sensor#4
(for NdFeB Magnets) -80
-2 -1 0 1 2
Figure 11
HMC1501 Array Position (inches)

60 Figure 13
HMC1501 Combined Bridge Waveforms
DV Signal Output (millivolts)

40 Vs = 5 volts

20 Once the routine has ascertained the correct bridge

and its analog value, a final value can be chosen to
0
relate the position to a number. For example, if each
-20 bridge is connected to an 8-bit Analog-to-Digital
Converter (8-bit ADC), then 256 possible values (1 to
-40
256 points) can represent a magnet position in its
-60 displacement range. With an array of four sensors, a
number from one to 1024 points can represent the
-80
-3 -2 -1 0 1 2 3
entire travel range. If sensor #2 is chosen with the
value of 132 points, then a point value of 388 would
Position (inches)
represent the relative position (256 points for sensor
Figure 12 #1 plus 132 points for sensor #2) of the magnet.
Linear Displacement Waveform
Two notes on the above description you should be
The above figures show a design for about a 2 inch aware of. One is that the slopes can be inverted if the
displacement sensor system. Typical resolution of sensors are rotated ±90° so that you would look for
position is around 2 mils (0.002”) with an accuracy of negative slopes instead of positive slopes. The second
0.1% largely dependant on the supporting interface is that ADC resolution increases can bring much more
electronics. precision if needed. The above example is 8-bit, but
10, 12, and 16 bit ADC devices can be used. Figure 14
In interpreting the DV signals from each sensor bridge, shows a typical circuit for the above example design.
each bridge is calibrated by cancelling out the offset
error voltage, and by measuring the peak-to-peak MOTOR SHAFT POSITION SENSING
bridge waveform and creating a scaling factor for each
bridge’s output so that the final adjusted peak-to-peak Not all motors have the conveinence of having the end
range is the same. Once calibrated, each sensor of a shaft available for magnet placement. For those
voltage value is collected and a comparision routine is applications where the magnets must be placed along
started. The routine takes the calibration corrected the circumference of the shaft, several approaches are
values and creates a “slope” value in-between available. The “wider position sensing” section covers
adjacent sensors. From figure 12, note that the bridges the sensor at the end of the shaft, but two HMC1512
with the magnet closest to them will demonstrate a could be positioned 180° on each side of the shaft with
positive slope on one or both sides of the measured a split magnet located above or below the sensors to
DV. The routine then locates the smallest DV with one come close to the end position sensing. However,

Solid State Electronics Center • www.magneticsensors.com • (800) 323-8295 • Page 5

AN211
SENSOR PRODUCTS
there are new magnet designs available from various
manufacturers that can create ring shaped magnets
that can create north or south pole magnetized pie
SHAFT
sections for shaft position sensing.
S RING MAGNET
Vcc N
5.0v U1
N
INV A
NINV A
OUT- - S
HMC1501 AN0
OUT+ +
U6
S
U1 N
HMC1501
INV B
NINV B
N S
HMC1501
U5 U7

4:1 MUX MPU

U1
INV C
NINV C Figure 15
HMC1501
Ring Magnet Design
U1
INV D
360 DEGREE ROTATION SENSING
NINV D
HMC1501
To create a full 360° rotational position sensing
solution, the HMC1512 sensor can be combined with a
Figure 14 hall effect sensor. Most hall effect sensors use silicon
Array Circuit semiconducting materials to create a proportional
voltage output as a magnetic field vector slices
With sectioned ring magnets, at least two ways could orthogonally through the slab material with a bias
be envisioned to locate motor shaft position. The first current flowing through it. Figure 16 shows this
is to locate one or two narrow pie section pole faces principal.
and wrap an array of HMC1501 sensors; much like the
previous linear position sensor section described. M

Then each sensor gets a portion of shaft rotation to

Magnetic Field
operate on. The second way is to conserve on sensors
and use a multi-section ring magnet to provide a Hall Effect Sensor
repeating pattern of north and south magnet poles. For
example, a ring magnet of 6 to 8 sections and two
HMC1501 sensors could offer precise shaft position.
BIAS
CURRENT
To keep accuracy high the ring magnet needs to keep
the pole faces in smaller increments than when using
Hall Effect sensors in a linear (amplitude) mode of
+ -
operation. Also some forced spacing between north M
and south poles is required to ensure that no gaps in M Hall Effect Voltage

saturating magnetic fields are small. Figure 15 shows Figure 16

a typical ring magnet design of shaft position sensing. Hall Effect
As you can see, the two HMC1501 sensors do not Although hall effect sensors do not offer the sensitivity
cover the whole rotation of the shaft, but concentrate or precision for accurate position sensing, they are
on one location. This is to best group the sensor used for 360° position sensing as “polarity” detectors
assembly for practical packaging reasons and to to determine which half of the HMC1512’s rotation a
consider the need of magnetic shielding from motor magnet is in. Figures 17 and 18 show a typical
field coils in close proximity. Another item to note is orientation and resulting waveforms for 360° position
that there is pattern overlap in the placement of the sensing.
two sensors so that one or the other will be in
saturation and that the one sensor who’s DV is closest
to zero will be the best measurement.

Solid State Electronics Center • www.magneticsensors.com • (800) 323-8295 • Page 6

AN211
SENSOR PRODUCTS
HALL EFFECT SENSOR
MINIMALIST POSITION SENSING
HMC1512
To make one sensor handle larger linear or angular
ranges than specified, is to be creative with magnet
N S designs to force in-specification field directions during
a complete linear translation or a whole one-turn
rotation of the shaft. For the linear application, Figure
19 shows a typical method.

SENSOR

ROTATING SHAFT MAGNETS

Figure 17
360° Position Sensing
N
As the magnetic flux rotates about the HMC1512 and SENSOR S
the hall effect sensor, the hall effect sensor’s voltage DISPLACEMENT
PATH
will reverse its polarity at the flux vector changes from
back-to-front to front-to-back through the silicon slab. Figure 19
Tilting Magnets Method
80
Sensor A
Sensor B The above figure shows two magnets tilted slightly
60 Hall from each other while maintaining a consistent gap in
DV Signal Output (millivolts)

40
spacing in which a sensor will travel between the
magnets. In the near position, a downward angled flux
20 path is produced, with a horizontal direction at mid-
travel, and an upward angle at the far position. Thus a
0 single bridge’s linear sensing range is spread out
through a fairly long displacement length. Either the
-20
magnets or the sensor itself can be made to move
-40
relative to the other.

-60 For angular position, Figure 20 shows two ring

-180 -90 -45 0 45 90 180 magnets on a rotating shaft. Each ring magnet is
theta (degrees) eccentric to the shaft and magnetized parallel to the
Figure 18 shaft. Each magnet is 180 degree eccentric from each
360° Sensing Waveform other and has a gap for the sensor to reside into. Two
position sensors are placed 90 degrees apart to
By placing a comparator on the hall effect sensor perform a total 360 degree position sensing
analog output, a digital representation of half rotation arrangement.
polarity is achieved. When combined with ±90°
sensing circuits of the HMC1512, the sensing range is One note to mention is that only the outer area of the
doubled providing a complete ±180° or 360° rotational eccentrics are magnetized so that the flux direction will
sensor of high accuracy. One note is to mechanically create a “cage” of lines that bend inward or outward
ensure that the hall sensor is nearly perfectly depending on shaft position.
orientated with respect to the HMC1512, so that the
arctangent equation deriving the heading arrives at the KEY SENSOR SPECIFICATIONS
end positions just as the hall sensor output achieves a
zero volt output. (Patent Pending, Patent Application In choosing appropriate interface circuitry to sensor
Number H0003321) bridges, certain key specifications should be
emphasized. The first specification to be noted is the
bridge resistance. Since the HMC1501 and HMC1512
have different bridge resistances (5000 and 2100
ohms respectively), the user may favor over the other
Solid State Electronics Center • www.magneticsensors.com • (800) 323-8295 • Page 7
AN211
SENSOR PRODUCTS

THE HUMAN RESPONSE

When working with position sensing that interacts to

human manual inputs, note that there is a minimum
latency that can be tolerated when eye-hand
coordination is desired. This typically is percieved as
20 position updates per second, or about 50
milliseconds per update. So when allocating time for
S SENSOR analog-to-digital conversion, ensure extra budgeted
N time for computation and display settling times. This is
SENSOR
especially true when using Liquid Crystal Displays in
cooler environments.
S
N
THE AMR VALUE PROPOSITION
RING
MAGNETS
The use of Anisotropic Magneto-Resistive sensors
SHAFT provides a contactless method of achieving angular or
linear position sensing. Unlike Hall Effect Devices that
require kilo-gauss level magnetic fields from rare earth
magnets, the HMC1501 and HMC1512 provide a
Figure 20 higher resolution sensor with much less field strength.
Eccentric Ring Magnets The dominant limiting factor on resolution is typically
the analog to digital converter bit size over the
based on power consumption or noise performance. If boltzman noise of the resistive elements..
power consumption is of primary importance, the user
has the option of gating or “duty cycling” the sensor Linear sensing ranges of the HMC1501 and HMC1512
bridge power supply to lower the total energy demand. can be easily extended by using multiple sensors and
If low noise performance is the utmost criteria, then component counts can be minimized by multiplexing
lower bridge resistance favors lower noise voltages. sensor output signals to one or more analog to digital
converter ICs. Multiplexing can also be utilized to
Bridge sensitivity is another key specification that reduce sensor power consumption in energy limited
should be examined by users. Both the HMC1501 and applications.
HMC1512 exhibit a 1.8 to 2.1 millivolts per degree
sensitivity in their most linear regions of performance. Both sensor types are available in small SOIC-8
Given a nominal ±120 millivolt output voltage and sub packages or in raw die form by special request. These
micro-volt noise floors, allows for better than tenths of plastic encapsulated silicon sensor die are inherently
a degree angular resolution. By choosing the right insensitive to mechanical shock and vibration.
signal conditioning bandwidth and the amount of
effective bits of analog-to-digital converter resolution, DEMONSTRATION PRODUCTS
the user can play into the strengths of these AMR
sensors. For further interest, check out Honeywell’s
demonstration products; the HMR4001 and the
Another key speification is the bandwidth of the sensor HMR4007. The HMR4001 uses a single HMC1512
bridge. While the HMC1501 and HMC1512 promise up sensor for linear or angular position sensing
to 5 Mega-Hertz of bandwidth, careful attention to applications. The HMR4007 uses seven HMC1501
magnetic and electronic design practices must be paid sensors to permit extended range linear position
when position sensing at high shaft speeds. Particular sensing.
emphasis should be made to keep bridge to signal
conditioning layouts tight to minimize stray
capacitance that may eat up precious system
bandwidth. This becomes very critical when using
multipole magnets in angular rotation.

900281 01-02 Rev -

Solid State Electronics Center • www.magneticsensors.com • (800) 323-8295 • Page 8