INSTRUCTION SHEET IS-SX1913

6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445 STYLE NUMBER: SX1913K, SX1913P
www . quoizel . com

PACKAGE CONTENTS ISSUED 04-2010

PART DESCRIPTION QUANTITY

A
A Crossbar 1 pc
1 pc B J
B Green Ground Screw
2 pcs C
C Hex Nut
Nipple 1 pc D
D
E Lock Washer 2 pcs E

F Canopy Chain Loop 1 pc K

F
G Canopy Lock Ring 1 pc
H Fixture Chain 1 pc G

I Ceiling Canopy 1 pc H

J Fixture Loop Assembly 1 pc

I
K Socket Assembly 1 pc

WARNINGS AND CAUTIONS

WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb9s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.

PREPARATION

● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (3) 60W B10 candelabra base bulbs .
● Helpful Tools (not included): Wire strippers.

1 OF 3
INSTALLATION INSTRUCTIONS STYLE NUMBER: SX1913K, SX1913P

STEP 1:
a. Thread the Fixture Loop Assembly onto the Hex
Coupling on the top center of the Socket Assembly.
Hand-tighten until snug. Fixture Loop Assembly

Hex Coupling

Socket Assembly

STEP 2:
a. Secure the Crossbar onto the Outlet Box with Outlet
Box Screws. Tighten until snug. Outlet Box

Crossbar

Outlet Box
Screw

STEP 3:
Pliers is required on this step.
a. Thread one Hex Nut onto top end of the Nipple.
b. Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of Lock Washer
the Crossbar. Crossbar
c. Using pliers, thread the Hex Nut against the Crossbar Hex Nut
and hand-tighten until snug.
d. Thread another Hex Nut onto the bottom end of the
Nipple.
Nipple

Hex Nut

2 OF 3
INSTALLATION INSTRUCTIONS STYLE NUMBER: SX1913K, SX1913P

STEP 4:
a. Adjust the Fixture Chain to your desired length by
removing the links if needed.
Please note that depends on chain material
thickness, you might be required to use chain pliers to Nipple
spread links open. Hex Nut
b. Pull the supply wires through the Fixture Chain
alternating links. And then pull the wires through the Lock Washer
following components in turn:
Canopy Lock Ring, Ceiling Canopy, Canopy Chain
Canopy Chain Loop
Loop, Lock Washer, and Nipple.
c. Place Lock Washer over the end of the Nipple and
thread the Canopy Chain Loop onto the end of the
Nipple.
Ceiling
d. Using pliers, thread the Hex Nut against the Canopy Canopy
Chain Loop and tighten until snug.
e. Attach one end of the Fixture Chain onto the Fixture
Loop and attach the another end of the chain onto the
Canopy Chain Loop. Fixture Chain
f. Refer to STEP 5 - Wire Connections to connect wires.
g. Push the Ceiling Canopy upward over the Outlet Box.
h. Thread the Canopy Lock Ring onto the Canopy Chain
Loop and tighten until snug to secure the Ceiling Canopy Lock Ring
Canopy.

Fixture Loop

STEP 5:
Use Wire Connectors (not supplied) to connect the
WHITE OR RIBBED WHITE OR RIBBED
wires.
a. Connect the House Ground Wire to the Fixture Ground FROM HOUSE FROM FIXTURE
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side). BLACK (OR RED) WIRE BLACK OR SMOOTH
c. Connect the House Black (or Red) Wire to the Fixture FROM FIXTURE
FROM HOUSE
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the GROUND WIRE GROUND WIRE
Outlet Box.
FROM HOUSE FROM FIXTURE

STEP 6:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.

Your installation is completed now. Restore electricity. Retain this sheet for future reference.

3 OF 3