Scribd
Upload
238 views1 page

Title: WQ 482 Welding Procedure Specification (WPS) : Supersedes

This document provides a welding procedure specification for manufacturing canisters using shielded metal arc welding with carbon steel material. It specifies the joint preparation and cleaning required, as well as filler metal, base metal thickness, welding positions, techniques, and electrical characteristics including current, voltage, and wire size. Temperatures for interpass and postweld heat treatment are also outlined.

Uploaded by

dethamrn
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
238 views1 page

Title: WQ 482 Welding Procedure Specification (WPS) : Supersedes

This document provides a welding procedure specification for manufacturing canisters using shielded metal arc welding with carbon steel material. It specifies the joint preparation and cleaning required, as well as filler metal, base metal thickness, welding positions, techniques, and electrical characteristics including current, voltage, and wire size. Temperatures for interpass and postweld heat treatment are also outlined.

Uploaded by

dethamrn
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 1

SUPERSEDES :

TITLE :
WQ 482 WELDING PROCEDURE SPECIFICATION (WPS)
This Welding Procedure Specification is propose for Manufacture Canister material AISI 1041 Carbon steel
using Sheilded metal Arc Welding
Typical welding deposit as specified in PQR No:
Preparation should be taken as follow:
-Remove all oils, greases,paint,dirts and all foreign material by using grinding and/or MEK(methil ethil keton)
-Followed by wiping with clean lint free until no more soil can be removed.

JOINTS (QW-402) POSTWELD HEATTREATMENT (QW-407)


Groove Design : Butt V groove Tempetarure : NONE
Backing : NO Time Range N/A
Backing Material (Type) : N/A Other Welding wrap part and slow coll
Other : N/A temper bead technique if possible

BASE METALS (QW-403) GAS (QW-408)


P No. :1 Shielding Gas : N/A
Percent Composition (mixtures) :-

Thickness Range : Variation Flow Rate :


Pipe Diameter Range : N/A Gas Backing : N/A
Other : carbon steel Trailing Shielding Gas Composition : N/A

Other : N/A

FILLER METALS (QW-404) ELECTRICAL CARACTERISTICS (QW-409)


F No. : 1 Other Current (AC/DC) : DC Polarity revercse
A No. :4 Other Amps (range) : WP Volts(range) : WP
Spec No. (SFA) : 5.5 Others Parameters setting :
AWS No. (Class) : A 5.5
Size of Electrode : WELDER PREFERENCE
Size of Filler : 3 mm Weld wire Current Voltage
Electode Flux : N/A mm inch ampere volts
Consumable Insert : N/A 3 1/8" 90-140 22-26
Other : N/A

POSITION (QW-405) TECHNIQUE (QW-410)


Position of Groove : WELDER PREFERENCE String or weave Bead : String
Welding Progression : WELDER PREFERENCE Oriffice or Gas Cup Size : N/A
Other : N/A Initial & Interpass Cleaning (Brushing, Grinding etc.)
: wire brush and sand blasting
Methode of Back Gouging : N/A
Oscilation : N/A
PREHEAT (QW-406) Contact Tube to Work Distance : N/A
Preheat Temperature : N/A Multiple/Single Electodes : SINGLE
Interpass Temperature : 200-350oC (400-650°F) Multiple/Single Pass (per side): MULTIPLE
Preheat Maintenance : N/A
Other : N/A Travel Speed (Range): WELDING PREFERENCE
Other

You might also like