Scribd
Upload
507 views2 pages

Sharp Error l1-00 Al-Ar

This technical bulletin summarizes a parts change for certain Sharp copier models to address an intermittent copy lamp issue. It notes that if an L1-00 trouble occurs, replacing resistor R239 with a new 5.6k ohm type resistor on the MCU PWB should resolve the problem. Technicians are advised to check transistor Q108 when troubleshooting the MCU PWB after replacing the resistor. Part numbers for the replaced resistor and updated MCU PWB are provided, along with notes about model compatibility.

Uploaded by

sydrous
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
507 views2 pages

Sharp Error l1-00 Al-Ar

This technical bulletin summarizes a parts change for certain Sharp copier models to address an intermittent copy lamp issue. It notes that if an L1-00 trouble occurs, replacing resistor R239 with a new 5.6k ohm type resistor on the MCU PWB should resolve the problem. Technicians are advised to check transistor Q108 when troubleshooting the MCU PWB after replacing the resistor. Part numbers for the replaced resistor and updated MCU PWB are provided, along with notes about model compatibility.

Uploaded by

sydrous
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Copier

Technical Bulletin Sharp Electronics Corporation


Services and Support Group
1300 Naperville Drive
Romeoville, IL 60446
Number: AR-153E-007 Date: June 2003

Subject: Parts Change To The MCU PWB (L1-00 Trouble).

1. Model: AL-1215/1530CS/1540CS/1551CS
AR-153E/157E/153EN/157EN

2. Symptom: The Copy Lamp is intermittently turned off which may cause L1-00
trouble.

3. Corrective Action: If L1-00 trouble is experienced, replace the resistor R239 to the
new style (5.6k ohm type).

4. Note: Check the condition of transistor Q108 (PN: VSKTA1281++-1)


when troubleshooting the MCU PWB after replacing R239.

Refer to page 2 for part descriptions and price ranks.

DCE-370 Bulletin #: AR-157E-007 Page 1 of 2


From January 2003 production.
Model P/G Previous Part New Part Price Description Inter-
No. Rank change-
ability
AL-1215
AL-1530CS
30-109
AL-1540CS
VRS-CZ1JD471J VRS-CZ1JD562J AA Resistor R239 3
AL-1551CS
AR-153E
28-109
AR-157E
AL-1215 CPWBX0112QS31 CPWBX0121QS41
BW
AL-1530CS CPWBX0112QS32 CPWBX0121QS42
30-901
AL-1540CS CPWBX0112QS33 CPWBX0121QS43
AL-1551CS CPWBX0112QS34 CPWBX0121QS44
BX MCU PWB 1
AR-153E CPWBX0121QS3C
28-901 CPWBX0112QS3D
AR-157E CPWBX0121QS3D
AR-153EN CPWBX0121QS33
30-901 No Change BY
AR-157EN CPWBX0121QS34
Interchangeability
1. Interchangeable 4. Not interchangeable
2. Current type can be used in place of new type. 5. Interchangeable if replaced with
New type cannot be used in place of current type. same types of related parts in use.
3. Current type cannot be used in place of the new type. 6. Others.
New type can be used in place of current type.

Note 1: When replacing the MCU PWB on the AR-153E/157E/153EN/157EN make sure to
look at the Serial Number Plate on the rear of the machine to determine if you have an “E”
model or “EN” model. The MCU PWB’s are different for these models. On the “E” version
Connector CN106 is 4 pins and on the “EN” version CN106 is 10 pins.

Note 2: On machines produced from January 2003 production resistor R239 has been changed
to the 5.6k ohm type so the new MCU PWB’s will have the new style resistor.

DCE-370 Bulletin #: AR-157E-007 Page 2 of 2

You might also like