2005 Hutchison Harbour Ring Enterprises Limited This device complies with Part 15 of the FCC Rules.

All rights in this publication are reserved and no part may

be reproduced without the prior written permission of
the publisher. The contents of this publication are
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
i.Tech Clip V
believed to be correct at the time of going to press, but including interference that may cause undesired
any information, specifications, products or services operation.
mentioned may be modified, supplemented or Caution: Changes or modifications not expressly
withdrawn without further notice. approved by the party responsible for compliance could
void the user's authority to operate the equipment.
The Stylized i.Tech logos are trademarks owned by
Hutchison Harbour Ring Enterprises Limited or its i.Tech declares under our sole responsibility that the
affiliates. headset is in conformity with the provisions of the
following Council Directives: 1999/5/EC
Bluetooth and the Bluetooth logos are trademarks
®

owned by Bluetooth SIG, Inc, USA and licensed to i.Tech

Dynamic Limited.

01/2006 S3J-51A05054-03
User Guide
 Table of Contents
Voice Dialing from Your Headset ..................................................................................................................... 11
i.Tech Clip V Overview ...................................................................................................................................................... 1 Last Number Redialing from Your Headset ................................................................................................... 12
Getting Started ................................................................................................................................................................. 2 Rejecting a Call (Handsfree Profile ONLY) …………........................................................................................ 12
Charging Your Headset ................................................................................................................................................... 3-5 Transferring a Call (Handsfree Profile ONLY) …………................................................................................... 12
Charging Time ...................................................................................................................................................... 4 Adjusting the Volume ..................................................................................................................................................... 13
Talk and Stand-by Time ..................................................................................................................................... 4 Resetting the Headset ..................................................................................................................................................... 13
Low Battery .......................................................................................................................................................... 5 Care and Maintenance .................................................................................................................................................... 14-15
Turning your Headset On and off ................................................................................................................................ 5-6 Headset ................................................................................................................................................................. 14
Pairing Your Headset ...................................................................................................................................................... 7-9 Built-in Battery .................................................................................................................................................... 15
Using Your Headset ......................................................................................................................................................... 9-12 Charger .................................................................................................................................................................. 15
Answering a Call .................................................................................................................................................. 9 Safety Information ........................................................................................................................................................... 16
Ending a Call ......................................................................................................................................................... 10 Troubleshooting ................................................................................................................................................................ 17-18
Dialing from Your Mobile Handset .................................................................................................................. 10 Product Specifications ..................................................................................................................................................... 19
Muting the Built-in Buzzer …….......................................................................................................................... 10 Declaration of Conformity (DoC) ................................................................................................................................... 20
Muting the Microphone ………........................................................................................................................... 11
00 00
 i.Tech Clip V Overview Getting Started

1
1. Microphone 6 2
2. Volume Key
3. Status Indicator 7 3 To use your i.Tech Clip V (“the headset”), please follow
4. Built-in Buzzer
5. Charging Socket 5 4 these simple steps:
6. Built-in Rechargeable Battery 8 Charge your headset
7. Multi-function Button (MFB)
Pair your headset with a Bluetooth-enabled mobile handset
8. Earphone

01 02
 Charging Your Headset Charging Your Headset
Connect the charger to an AC wall outlet (mains socket) and the charger plug to the headset’s charging socket
(fig.1). The LED will be red while charging.
IMPORTANT Charging indication will be delayed for a few seconds if the headset has not been used for a long
time or the battery is drained.
Charging Time
The Headset comes with a built-in Charging the battery fully is normally within 3 hours. When the battery is fully charged, the LED will turn blue and
Charger
Charging remain on. Disconnect the charger from AC wall outlet (mains socket) and the headset. Press and hold the MFB
rechargeable battery. Prior to using the Socket
(fig.1) for 2 seconds to turn the headset on, please refer to “Turning Your Headset On and Off” .
headset, it is recommendable to charge the Talk & Standby Time
battery fully for the first time. Charger Plug The fully charged battery offers up to 6 hours talk time and up to 120 hours standby time. When no calls are in
progress, the headset remains turned on in standby mode.
(fig.1) (fig.2)
03 04
 Low Battery Turning Your Headset On and Off
When the headset is on and the battery becomes low, the status indicator flashes red and the
headset emits a beep every 1 minute. Please recharge the battery as described above.
If you are setting up the headset and your mobile phone in a noisy environment, we advise
you to put on the earphone first so that the beep will be more audible.

Turning Your Headset On and Off Turning Off the Headset

Press and hold the MFB for approximately 3 seconds until you hear a long beep. The status indicator will stop
Turning On the Headset
flashing.
Press and hold the MFB for 2 seconds until you hear a short beep. The status indicator will then flash blue.
IMPORTANT Press the MFB again after the headset switched on each time you turn on the headset to reactivate IMPORTANT To disconnect the Bluetooth connection, press the MFB firmly to turn off your headset. If you will
pairing so that the connection between the headset and the mobile handset is resumed. For pairing , please refer to not be using the headset for a while, you should consider turning off the Bluetooth function on your mobile
“Pairing Your Headset” on page 7-8. phone as well.
05 06
 Pairing Your Headset Pairing Your Headset

The headset only works with Bluetooth-enabled

mobile phones. Prior to using and pairing your
headset for the first time, please check if your 1. Place the headset and the mobile handset no more then 1 meter apart and ensure there is nothing in between.
mobile phone is Bluetooth-enabled. 2. Ensure the headset is OFF.
3. Press and hold the MFB approximately 8 seconds until the headset status indicator alternately flashes blue and
The pairing instructions for a typical Bluetooth- Up to 1 metre red.
enabled mobile phone are explained on the next 4. Activate your mobile handset’s Bluetooth function by referring to your mobile handset user guide for details.
page. The headset pairing procedure may vary 5. Set the mobile handset to search for Bluetooth devices within 1 meter range as instructed in the mobile handset
depending on the model of your mobile phone. user guide and select “i.Tech Clip V” from the list.
Please contact the manufacturer of your mobile 6. Enter the preprogrammed passkey “0000” and press “OK” to pair your headset and mobile handset. When the
phone or its agent for further information. pairing is complete, the headset status indicator will flash blue rapidly 5 times followed by a long beep.
07 08
 7. Press “Return” to go back to your mobile handset’s main menu. For certain mobile handset models, a headset Ending a Call
icon will be shown on the screen. You should now be able to make and receive calls using your headset.
Press the MFB to end your call or end the call via your mobile handset in the normal way.
IMPORTANT If the pairing cannot be completed within 2 minutes while the pairing mode is activated, the headset
status indicator flashes purple followed by 3 beeps and the headset is turned off. Please repeat the above pairing Dialing from Your Mobile Handset
procedures. Simply make calls on your mobile handset in the normal way.
Muting the Built-in Buzzer
Using Your Headset Press and hold the volume key for two seconds until status indicator flashes RED once to mute the Buzzer and press
and hold the volume key for 3 seconds to deactiveate the muting function while your mobile phone remains in
Answering a Call
standby mode.
When there is an incoming call, you will hear ringing through the earphone and the built-in buzzer. Press the MFB
IMPORTANT: If you do not wish to be disturbed at all, you may consider resetting the mobile phone setting to
to accept the call or answer the call via your mobile handset in the normal way.
restrict incoming calls. Please refer to your mobile phone user guide for set up details.
IMPORTANT ou can stop the buzzer alert by pressing the volume key once. The buzzer will ring again when there is
another incoming call.
09 10
 Using Your Headset
Last Number Redialling from Your Headset
Short press the MFB on your headset twice.
Muting the Microphone IMPORTANT The above functions are only applicable to mobile handsets with Bluetooth Handsfree Profile.
You can put a call on hold by muting the microphone. Functionality varies depending on the mobile handset model you have. Please refer to your mobile handset user
Press and hold the volume key for two seconds until status indicator flashes Red to mute built in Microphone guide for additional information.
and press and hold the volume key for 3 seconds to deactivate the muting function while conversation.
Rejecting a Call (Handsfree Profile ONLY)
Voice Dialling from Your Headset Press and hold the volume key then press and hold the MFB until the incoming call is rejected.
If your mobile handset is equipped with a voice dialling function, simply press the MFB on your headset, and Transferring a Call (Handsfree Profile ONLY)
when you hear a beep say the voice tag. Press and hold the volume then press and hold the MFB until the audio is transferred from headset to your
IMPORTANT Please make sure voice tag into the mobile handset first before using voice dialling function. mobile handset during conversation.
11 12
 Adjusting the Volume Care and Maintenance
Press the Volume Key repeatedly until you reach the desired volume level. The listening volume may be affected Headset
by the volume setting of the caller’s phone as well. Re-adjust the listening volume again when necessary. • Consider turning your headset off before placing it in your pocket or bag. If the MFB is accidentally depressed,
your mobile handset may place an unintended call.
Resetting the Headset • Do not expose the headset to liquid, moisture or humidity as it is not waterproof.
• Do not use abrasive cleaning solvents to clean the headset.
You may reset the headset to its original settings at anytime, in doing this you also clear all current pairing
settings. • Do not expose the headset to extremely high or low temperatures.
1. Ensure the headset is OFF. • Do not dispose of the headset in a fire as it will result in explosion.
2. Press and hold the volume key for 20 seconds until the status indicator flashes Red and Blue. • Do not expose your headset to contact with sharp objects as this will cause scratches and damage.
3. Release the Volume Key. • Do not stick anything inside the headset as this may damage internal components.
4. Press and hold the Volume Key again until you hear 2 beeps. • Do not attempt to disassemble the headset as it does not comtain serviceable components.
5. Recharge the headset for a few seconds. • If you do not use the headset for long periods, be sure to store it in a dry place, free from extreme tempera-
The headset is turned off and returns to the original settings. All current pairings are cleared. tures and dust.
13 14
 Safety Information
Built-in Battery
• Check local laws regarding use of a mobile handset and headset whilst driving. If you use the headset while
• Do not attempt to replace the headset’s battery yourself as it is built into the headset and is not changeable.
• Charge the battery in accordance with the instruction supplied with this user guide.
driving, ensure your attention and focus remain on the road and you drive in a responsible and safe manner.
• Only use the manufacturer supplied charger when charging the headset. • Never allow children to play with the headset – small parts may be a choking hazard.
• Observe all signs that require an electrical device or RF radio product to be switched off in designated areas.
Charger These could include hospitals, blasting areas, and potentially explosive environments.
• Only use the manufacturer supplied charger when charging the headset. • Turn off your headset prior to boarding an aircraft. Do not use your headset in an aircraft.
• Do not disassemble the charger as it may expose you to dangerous voltages or other risks. Incorrect • Never mount or store your headset over any air bag deployment area as serious injury may result when an air
reassembly can cause electric shock when the headset is subsequently used. bag deploys.
• Do not use the charger outdoors or in damp areas. • Do not open or mutilate the built-in battery.
• Only charge the headset’s built-in battery in accordance with the instructuins in this user guide. • Dispose of batteries according to local regulations. Do not dispose as household waste.
• Avoid charging the headset in extremely high or low temperatures. • Dispose of the packaging and this product in accordance with the latest provisions.
15 16
 Troubleshooting Troubleshooting

If you are unable to connect your headset with your mobile handset or Bluetooth enabled device, please try the
following:
• Ensure your headset is turned on and is properly charged.
• Ensure the headset is paired with your mobile handset.
• Ensure your mobile handset’s Bluetooth feature is activated.Please refer to your mobile handset user guide for
specific instruction. The i.Tech Clip V Headset is compliant with and adopts the Bluetooth Specification 1.2. However, interoperability
• Ensure the headset is within a maximum of 10 meters of your mobile handset(s) and there are no obstructions, between the device and other Bluetooth-enabled products is not guaranteed because it depends on
such as walls or other electronic devices in between. compatibility. For more information on the compatibility between the device with other Bluetooth-enabled
products, please check with the manufacturer or browse:
If the above suggestions do not solve your problem, please recharge the headset and remove your mobile phone
battery for a while. Then start pairing again. http://www.itechdynamic.com
17 18
 Product Specifications Declaration of Conformity ( DoC )

We, i.Tech Dynamic Ltd., declare that the following product:

Bluetooth Specification: Version 1.2 Class 2
Bluetooth Profile Supported: Headset and Handsfree Product Name: i.Tech Clip V
Model No.: C51-A05054-XX
Range of Frequency: 2.4GHz Spectrum
Talk Time*: up to 6 hours
Is in conformity with the following essential requirements of Council Directive 1999/5/EC ( referred to as
R&TTE Directive ) : Article 3.1a, 3.1.b and 3.2. and the product is manufactured in accordance with Annex II of
Standby Time* : up to 120 hours above directive.
Nominal Charging Time: Within 3 hours
Dimensions: 46(L) x 18(W) x 22.5(H) mm * May vary due to users’ operation A copy of the Declaration of Conformity can be found at:
Weight: 16.7 grams mode and mobile phone settings. http://www.itechdynamic.com
19 20