Scribd
Upload
525 views

Leoxsys Wireless Router Config Ration

The LEO-300N-3G 3G Router supports the latest IEEE802.11N wireless standard and has a built-in USB 2.0 port to connect USB 2G/3G modems to create a WiFi hotspot. It can be set up by connecting the WAN port to an ADSL modem, LAN port to a computer, and accessing the default IP 192.168.7.1 with username "admin" and password "password". If the default gateway is not reached, the IP configuration can be renewed using ipconfig commands. Dynamic DNS service allows remote access using a hostname from providers like dyndns.com. The router settings can be reset to factory defaults using the

Uploaded by

Priyesh ET
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
525 views

Leoxsys Wireless Router Config Ration

The LEO-300N-3G 3G Router supports the latest IEEE802.11N wireless standard and has a built-in USB 2.0 port to connect USB 2G/3G modems to create a WiFi hotspot. It can be set up by connecting the WAN port to an ADSL modem, LAN port to a computer, and accessing the default IP 192.168.7.1 with username "admin" and password "password". If the default gateway is not reached, the IP configuration can be renewed using ipconfig commands. Dynamic DNS service allows remote access using a hostname from providers like dyndns.com. The router settings can be reset to factory defaults using the

Uploaded by

Priyesh ET
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

1. What is LEO-300N-3G 3G Router?

The LEO-300N-3G Wireless-N 3G Router is compatible with latest IEEE802.11N


standard which supports high data rate.It also supports WPS(WIFI Protected
Setup), 8 Multiple BSSID, QOS-WMM(Wireless Multimedia).

LEO-300N-3G router has a builtin USB 2.0 port, which is not provided in the latest
routers.

Ease to connect USB 2G/3G Modem with LEO-300N-3G and build up personal
WiFi Hotspot to connect computers/laptops/Iphones/Ipods/Wifi enabled mobile
phones.

2.How can I setup router?

Connect the WAN(blue color)port to the ADSL modem and LAN(yellow color)port
to your system. And the following are the default parameters for the setup,

Default Router IP : 192.168.7.1


Default Username : admin
Default Password : password
Default WiFi SSID : leoXsys

When you setup and open the router with the ip address 192.168.7.1 in the browser,
you will get home page of the router.

3.If I dont get home page with the above setup what can I do ?

Go to start menu-->Run. Type cmd or command the press ok. Check ipconfig, if
default gateway is not 192.168.7.1 then follow these steps, Release the connecton
using the command ipconfig /release. Reconnect it using the command ipconfig
/renew , then you will get default gateway 192.168.7.1 Now open the router with the
ip address 192.168.7.1 in the browser.

6.How can I setup DDNS?

Go to www.dyndns.com website and create one account.It will give you User Name
,Password and Hostname.Enter all details to router DDNS config page and submit
it.Once it is registered successfully with LEO-300N-3G router , You can access your
LEO-300N-3G router from anywhere through your Hostname provided by
www.dyndns.com.

11.What are default login username and password?


Default username : admin
Default password : password

13.How can I reset the router?

The device can also be reset back to factory default settings by clicking on
?LoadDefault? button. Use the restore feature only if necessary. This will erase
previously saved settings for the unit. Make sure to save your system settings before
doing a factory restore. Or you can hold the small button reset button ,which is
beside power button in the router, for 5 to 10 seconds then the router will be reset.

15.How can I know the number of users who are connected through wireless?

Go to Wireless-->Station list, here you will get MAC addresses of the systems which
are connected through wireless.

You might also like