Chapter 3

Basic Data Communication

Technology

JKKD MTI UI 2009 1

Physical Layer
 responsible for the establishment,
maintenance and termination of physical
connections between communicating devices.
 transmits and receives a stream of bits.
 no data recognition at the physical layer.
 operation is controlled by protocols that
define the electrical, mechanical, and
procedural specifications for data
transmission

JKKD MTI UI 2009 2

 UTP Specifications
UTP Maximum Data Attenuation / Applications
Category Speed NEXT limit

Cat 1 < 1Mbps   Telephone lines

Cat 2 4 Mbps 4 MHz 4 Mbps Token-Ring over UTP

Cat 3 16 Mbps 16 MHz 10baseT Ethernet. Tested for attenuation and near-end crosstalk up
to 16MHz.
Cat 4 20 Mbps 20 MHz 16 Mbps Token-Ring over UTP. Tested for attenuation and near-end
crosstalk up to 20MHz.
Cat 5 100 Mbps (2 100 MHz 100baseT (fast) Ethernet, 155 Mbps ATM, Gigabit Ethernet
pair)
1 Gbps (4 pair)
Cat 5e 100 Mbps (2 100 MHz 100baseT (fast) Ethernet, 155 Mbps ATM, Gigabit Ethernet
pair) Category 5e cable has a tighter quality control standard than
1 Gbps (4 pair) standard Cat 5 cable
Cat 6 2.5 Gbps (2 pair) 200 MHz None that require cat 6 at the time of this writing. The IEEE is
potentially up to working on a copper 10 Gbps Ethernet standard that would require
1 bps (4 pair) cat 6 if released.

JKKD MTI UI 2009 3

Unshielded Twisted Pair
 Consists of one or more pairs of insulated copper
wire twisted around each other at varying lengths
ranging from two to twelve twists per foot.
 The twisting is used as a mechanism to reduce
interference between pairs and from outside
sources that can cause data errors and
necessitate retransmission.
 These individually twisted pairs are then grouped
together and covered with a plastic or vinyl
jacket, or sheath.

JKKD MTI UI 2009 4

Unshielded Twisted Pair
 All UTP cables are not created equal.
 there are six different categories of UTP as
specified by EIA/TIA 568
 EIA/TIA 568 also specifies:
 The topology, cable types, and connector types to
be used in EIA/TIA 568 compliant wiring schemes
 The minimum performance specifications for
cabling, connectors and components such as wall
plates, punch down blocks and patch panels to be
used in an EIA/TIA 568 compliant installation

JKKD MTI UI 2009 5

Signal Degradation
 Attenuation is the decrease in the power of
signal over a distance in a particular type of
wire or media.
 Near-End Crosstalk (NExT) is signal
interference caused by a strong signal on
one-pair (transmitting) overpowering a
weaker signal on an adjacent pair (receiving).
 Near End Crosstalk and Attenuation to
Crosstalk Ratio (ACR) are both measured in
dB or decibels.
JKKD MTI UI 2009 6
Coaxial Cable
 Coaxial cable, more commonly known as coax
or cable TV cable, has specialized insulators
and shielding separating two conductors
allowing reliable, high speed data
transmission over relatively long distances.
 Coax comes in various thicknesses and has
been historically used in Ethernet network
architectures.
 Modern local area network implementations
rarely use coaxial cable today.
JKKD MTI UI 2009 7
Coaxial Cable

 With the advent of cable modems and the use of the cable
television system as a mechanism to provide high speed Internet
connectivity to homes coaxial cable continues to play an
important role in data communication

JKKD MTI UI 2009 8

Fiber-Optic Cable
 Fiber optic cable is the current reliability and
performance champion of the data
communication world.
 Although the most expensive media choice
currently available, fiber optic media delivers
data transmission speeds measured in
Gigabytes (billions of characters) per second
over distances of measured in miles.

JKKD MTI UI 2009 9

 Fiber-Optic Cable
 Fiber Optic cable is also one of the most
secure of all media:
 it is relatively untappable, transmitting only
pulses of light, unlike all other guided media
which transmit varying levels of electrical
pulses.
 it is immune to electro-magnetic interference
contributing to its high bandwidth and data
transmission capabilities.
JKKD MTI UI 2009 10
Fiber Optic Cable

 Fiber optic cable requires careful handling.

JKKD MTI UI 2009 11

Light Transmission Modes
 Once a pulse of light enters the core of the fiber optic
cable, it will behave differently depending on the physical
characteristics of the core and cladding of the fiber optic
cable.
 In a Multimode or Multimode Step Index fiber optic
cable, the rays of light will bounce off of the cladding at
different angles and continue down the core while others
will be absorbed in the cladding.
 These multiple rays at varying angles cause distortion and
limit the overall transmission capabilities of the fiber.
 This type of fiber optic cable is capable of high bandwidth
transmission but usually over fairly short distances.

JKKD MTI UI 2009 12

 
 By gradually decreasing a characteristic
of the core known as the refractive
index from the center to the outer
edge, reflected rays are focused along
the core more efficiently yielding higher
bandwidth over several kilometers.
 This type of fiber optic cable is known
as Multimode Graded Index Fiber
JKKD MTI UI 2009 13
Guided Media Characteristics

JKKD MTI UI 2009 14

Point-to-Point Data
Transmission Technologies
 The most basic data communication
technologies are those used to directly
connect two devices.
 These connections can be used to connect a
computer to peripheral devices.
 Operating at layer one of the OSI Network
Reference Model, these technologies provide
a physical connection that can be used to
carry many higher level protocols.
JKKD MTI UI 2009 15
Serial Transmission
Standards
 Serial transmission is the basis of most
data communication between
computers.
 There are several different serial
communication standards available for
use in modern computers including RS-
232, USB, and IEEE 1394 (Firewire).

JKKD MTI UI 2009 16

Serial Transmission
Standards
 Serial transmission is the basis of most
data communication between
computers.
 There are several different serial
communication standards available for
use in modern computers including RS-
232, USB, and IEEE 1394 (Firewire).

JKKD MTI UI 2009 17

RS-232 Serial Connections

JKKD MTI UI 2009 18

RS-232
 RS-232 is currently the most commonly
used serial standard for modem
communication.
 Commonly referred to as a serial port.
 Most commonly implemented using DB-
25 or DB-9 connectors.

JKKD MTI UI 2009 19

Universal Serial Bus (USB)
 has all put replaced RS-232 in all but the most basic
applications.
 a high speed, multi-point serial communications
technology developed to resolve these shortcomings
of RS-232.
 There are two versions of USB currently available:
the original USB 1.1 specification and a newer higher
speed USB 2.0 specification.
 USB 2.0 is backwards compatible with USB 1.1.

JKKD MTI UI 2009 20

USB

 USB can be used to connect several

devices on the same port using hubs.

JKKD MTI UI 2009 21

USB Connector Cable

 There are two styles of USB connector in current widespread

use (A & B). These are also found in male and female forms
when used in extension cables.

JKKD MTI UI 2009 22

IEEE-1394
 IEEE-1394 is a high-speed serial solution ranging in
speed from 400 Mbps (original specification) to 800
Mbps (1394b).
 IEEE-1394 includes support for isochronous
communication.
 Isochronous communication guarantees data delivery
at a constant, pre-determined rate.
 The constant data delivery rate reduces the need to
buffer data thereby greatly reducing the cost of
implementing the technology compared to a
traditional asynchronous solution.

JKKD MTI UI 2009 23

Firewire (IEEE-1394) Cable

 Commonly used to connect multimedia

devices to PC’s

JKKD MTI UI 2009 24

Centronics Cable

 A common means of connecting

printers to PC’s

JKKD MTI UI 2009 25

Wireless Technologies

 There are two technologies that have

been developed as wireless cable
replacements: Infrared (IRDA) and
radio (Bluetooth).

JKKD MTI UI 2009 26

IrDA
 IrDA:
 signals are point-to-point nature,
 have a narrow angle (30 degree cone),
 are limited to around meter, and
 have a throughput of 9600 bps to 4 Mbps
 IrDA has proven to be a popular technology
with compliant ports currently available in an
array of devices including: embedded devices,
pagers, phones, modems, cameras, watches,
computers (PCs) and laptops, PDAs, printers,
and other computer peripherals

JKKD MTI UI 2009 27

Bluetooth
 Bluetooth is the name given to an emerging wireless radio frequency
(RF) communication standard.
 Bluetooth uses radio frequency communication in the unlicensed 2.4-
2.4835 GHz band using frequency hop spread spectrum (FHSS).
 By constantly changing frequency the transmission tends to be less
effected by interference, an especially desirable characteristic for
mobile computing applications.
 Bluetooth offers data speeds of up to 1 Mbps up to 10 meters.
 Unlike IrDA, Bluetooth supports a LAN-like mode where multiple
devices can interact with each other.
 The key limitations of Bluetooth are security and interference with
wireless LANs.
 Devices hitting the market that include Bluetooth include cellular
phones, PDAs, headphones, and mobile gaming platforms.

JKKD MTI UI 2009 28

Connecting to the Internet

JKKD MTI UI 2009 29

Public Switched Telephone
Network (PSTN)

 The public dial-up network is accessed

using a dial-up modem.

JKKD MTI UI 2009 30

Connecting to the PSTN

 The PSTN provides a switched circuit.

JKKD MTI UI 2009 31

Modems and the PSTN
 modem is actually a contraction for
Modulator/demodulator
 Most local loops that are used for connection to the
PSTN to supply switched, dial-up phone service are
physically described as two-wire circuits.
 Since one of these two wires serves as a ground wire
for the circuit, that leaves only one wire between the
two ends of the circuit for data signaling.
 Dial-up or switched two-wire circuits generate a dial-
tone

JKKD MTI UI 2009 32

Full-duplex
 Full-duplex transmission supports
simultaneous data signaling in both
directions.
 Full-duplex transmission might seem to be
impossible on two-wire circuits.
 Modems manufactured to the CCITT's V.32
standard (and the later V.34 standard) can
transmit in full-duplex mode, thereby
receiving and transmitting simultaneously
over dial-up two-wire circuits.
JKKD MTI UI 2009 33
Error Prevention
 Data transmission errors occur when
received data is misinterpreted due to
noise or interference on the phone lines
over which the data message traveled.
 Errors can be prevented by:
 Reducing the amount of noise or
interference on a given transmission line
 Employing modulation techniques that are
able to adapt to and overcome noisy lines
JKKD MTI UI 2009 34
 Modem Standards
Modem Standard Transmission Rate Baud Rate Data Compression Error Correction Modulation Method
V.90 56 Kbps down, 28.8 3200, 3000, V.42bis/MNP5 V.42/MNP4 Digital downlink & 9QAM
Kbps up 2400, &TCM uplink
2743,
2800,
3429, baud
V.34 28.8 Kbps 3200, 3000, V.42bis/MNP5 V.42/MNP4 9QAM &TCM
33.6 Kbps (optional) 2400,
2743,
2800,
3429, baud
V.32 ter 19.2 Kbps 2400 baud V.42bis/MNP5 V.42/MNP4 8QAM & TCM
V.32 bis 14.4 Kbps 2400 baud V.42bis/MNP5 V.42/MNP4 6QAM & TCM
V.32 9.6 Kbps 2400 baud V.42bis/MNP5 V.42/MNP4 4QAM & TCM

V.22 bis 2400 bps 600 baud V.42bis/MNP5 V.42/MNP4 4QAM & TCM

Bell 212A 1200 bps 600 baud 4PSK

Bell 103 300 bps 300 baud FSK

JKKD MTI UI 2009 35

V.90 Implementation

 V.90 has asymetrical data transmission

(up/down) transmission rates.
JKKD MTI UI 2009 36
Digital Subscriber Line (DSSL)

 Frequency Division Multiplexing in DSL

JKKD MTI UI 2009 37

DSL
 One of the faster broadband technologies
currently available is Digital Subscriber Line
(DSL).
 DSL provides an “always on” connection to
the Internet over the same copper wires that
provide dial-up telephone service.
 DSL uses the same copper loop as a POTS
line.

JKKD MTI UI 2009 38

DDL Standards and
Technology

 Unlike dial-up modems, there is little standardization

in the DSL world.
 Different vendors have developed different solutions
that use different frequencies and modulation
schemes.
 The only two devices that have to agree on the DSL
technology used are the DSL modem and the DSLAM.
 Most DSL service providers require customers to rent
or purchase DSL modems directly from them.

JKKD MTI UI 2009 39

DSL Architecture

JKKD MTI UI 2009 40

Cable Modems
 A provider of high bandwidth connectivity to
customer premises is the television cable
company.
 The cable provider’s infrastructure offers a
significantly higher bandwidth to the
consumer than the local loop provided by the
telephone company due to the coaxial cable
media used for cable television transmission

JKKD MTI UI 2009 41

Cable Modem Connection

JKKD MTI UI 2009 42

Cable Data Network

JKKD MTI UI 2009 43

 Copyright 2004 John Wiley &
Sons, Inc.
All rights reserved. Reproduction or translation of this
work beyond that permitted in section 117 of the 1976
United States Copyright Act without express permission
of the copyright owner is unlawful. Request for further
information should be addressed to the Permissions
Department, John Wiley & Sons, Inc. The purchaser
may make back-up copies for his/her own use only and
not for distribution or resale. The Publisher assumes no
responsibility for errors, omissions, or damages caused
by the use of these programs or from the use of the
information herein
JKKD MTI UI 2009 44