Hitachi Proprietary SC01486Z

SIM-RC00-00 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

SIM RC SECTION

SIM-RC00-00
Hitachi Proprietary SC01486Z
SIM-RC00-10 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

Contents

SIM-RC01-10 1. Reference Code

SIM-RC02-10 2. Reference Codes

SIM-RC02-20 2.1 SIM Reference Codes Detected by the Processor
SIM-RC02-410 2.2 SIM Reference Codes Detected by the SVP

SIM-RC03-10 3. SIM Format

SIM-RC00-10
Hitachi Proprietary SC01486Z
SIM-RC01-10 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

1. Reference Code
A six-byte reference code (RC) is provided for a SIM (service information message) to identify an
error and error section. The following shows 32 SIM bytes and reference codes.

Byte 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

SIM SSB 00 90 10 00 00 00 8F E0 44 10 00 04 00 80 04 0C 69 00 00 00 00 02 30 70 05 10 42 C0 F1 00 02 00

SSB13
SSB22, 23
SIM type
Indicates SIM. RC = 307080 F1: DKC SIM
F2: CACHE SIM
FE: DEVICE SIM
FF: MEDIA SIM

SIM-RC01-10
Hitachi Proprietary SC01486Z
SIM-RC02-10 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

2. Reference Codes
SIMs are roughly classified into two types: SIMs detected by the processor and SIMs detected by
the SVP.

SIM-RC02-10
Hitachi Proprietary SC01486Z
SIM-RC02-20 DKC515I
Rev.2 / Jul.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

2.1 SIM Reference Codes Detected by the Processor

SIM Reference Codes Detected by the Processor (1/12)
Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
LCP/FCP/ LCM Hardware error 21 3Z XY F1 Moderate Yes X: CHA PCB# (*1)
HTP error Y: LCP#1 (*3)
Z: LCP#2 (*3)
ADP permanent error 21 70 X0 F1 Moderate Yes X: CHA PCB# (*1)
ADP temporary error 21 71 XY F1 Service No X: CHA PCB# (*1)
Y: PORT# in PCB (*35)
ADP blocking 21 72 XY F1 Moderate Yes X: CHA PCB# (*1)
Y: PORT# in PCB (*35)
AL_PA value conflict 21 90 XY F1 Service No X: CHA PCB# (*1)
Y: PORT# in PCB (*35)
Link failure 1 21 93 XY F1 Serious Yes X: CHA PCB# (*1)
Y: PORT# in PCB (*49)
Link failure 2 21 94 XY F1 Serious Yes X: CHA PCB# (*1)
Y: PORT# in PCB (*48)
HTP hard error 21 A0 XY F1 Moderate Yes X: CHA PCB# (*1)
Y: HTP PATH# (*40)
HTP path temporary error 21 A1 XY F1 Service No X: CHA PCB# (*1)
Y: HTP PATH# (*40)
HTP path blocking 21 A2 XY F1 Moderate Yes X: CHA PCB# (*1)
Y: HTP PATH# (*40)
HTP blocking 21 A3 XY F1 Moderate Yes X: CHA PCB# (*1)
Y: PORT# in PCB (*35)
Optical signal output failure 21 A6 XY F1 Moderate No X: CHA PCB# (*1)
Y: LCP# (*35)
LED status change failure 21 A7 XY F1 Moderate No X: CHA PCB# (*1)
Y: LCP# (*35)
SFP Fail 21 A8 XY F1 Moderate No X: CHA PCB# (*1)
Y: PORT# in PCB (*35)
IP address conflict detection 21 A9 XY F1 Service No X: CHA PCB# (*1)
Y: LCP# (*35)
SFP warning 21 AA XY F1 Service No X: CHA PCB# (*1)
Y: PORT# in PCB (*35)
CHA CHK1A threshold over 30 70 XY F1 Service No X: CHA PCB# (*1)
Processor Y: MP# in PCB
error CHK1B threshold over 30 71 XY F1 Service No X: CHA PCB# (*1)
Y: MP# in PCB
CHK3 threshold over 30 72 XY F1 Service No X: CHA PCB# (*1)
Y: MP# in PCB
Processor blocking 30 73 XY F1 Moderate Yes X: CHA PCB# (*1)
Y: MP# in PCB
FM threshold over 30 74 XY F1 Service No X: CHA PCB# (*1)
Y: MP# in PCB
FM error 30 75 XY F1 Moderate Yes X: CHA PCB# (*1)
Y: MP# in PCB
Incorrect SUM value of FM 30 76 XY F1 (*27) No X: CHA PCB# (*1)
Y: MP# in PCB
Processor Memory 30 77 XY F1 Service No X: CHA PCB# (*1)
Temporary Error Y: MP# in PCB

SIM-RC02-20
Hitachi Proprietary SC01486Z
SIM-RC02-21 DKC515I
Rev.0 / Jan.2006 Copyright © 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor (2/12)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
CHA Processor Memory 30 78 XY F1 Service No X: CHA PCB# (*1)
Processor Temporary Error Y: MP# in PCB
error (ESCON-1 (*55))
Processor Memory 30 79 XY F1 Service No X: CHA PCB# (*1)
Temporary Error Y: MP# in PCB
(FICON-1 (*55))
Processor Memory 30 7A XY F1 Service No X: CHA PCB# (*1)
Temporary Error Y: MP# in PCB
(OPEN Fibre-1 (*55))
Processor Memory 30 7B XY F1 Service No X: CHA PCB# (*1)
Temporary Error Y: MP# in PCB
(NAS, iSCSI-1 (*55))
Processor Memory 30 88 XY F1 Service No X: CHA PCB# (*1)
Temporary Error Y: MP# in PCB
(ESCON-2 (*56))
Processor Memory 30 89 XY F1 Service No X: CHA PCB# (*1)
Temporary Error Y: MP# in PCB
(FICON-2 (*56))
Processor Memory 30 8A XY F1 Service No X: CHA PCB# (*1)
Temporary Error Y: MP# in PCB
(OPEN Fibre-2 (*56))
Processor Memory 30 8B XY F1 Service No X: CHA PCB# (*1)
Temporary Error Y: MP# in PCB
(NAS, iSCSI-2 (*56))
P/S OFF impossible 38 8F 00 F1 Moderate No
P/S OFF impossible (Device 38 9F 00 F1 Moderate No
reserved)
P/S OFF warning (SM 38 C0 00 F1 Moderate No
backup time not assured)

SIM-RC02-21
Hitachi Proprietary SC01486Z
SIM-RC02-30 DKC515I
Rev.3 / Oct.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor (3/12)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
CHA Undefined Package is 39 90 XY F1 Moderate No X: CHA PCB# (*1,*5)
Processor mounted Y: MP# in PCB
error V-R or serial number is 39 91 XY F1 Moderate No X: CHA PCB# (*1)
inconsistent Y: MP# in PCB
Replace failed 39 93 XY F1 Moderate No X: CHA PCB# (*1)
Y: MP# in PCB
Micro-program version up 39 94 X0 F1 Service No X: MP version after
replacing (*23)
Micro-program version up 39 95 XY F1 Service No X: Present MP version (*23)
impossible Y: reason code (*13)
CHF PCB exchange 39 99 XY F1 Service No X: CHA PCB# (*1)
Y: MP# in PCB
Warning of SM DISABLE 39 9A XY F1 Moderate No X: CHA PCB# (*1)
(MPA detected) (*37) Y: 0 = SM Side A Hotline
1 = SM Side B Hotline
SMA slave error 39 9B XY F1 Moderate No X: CHA PCB# (*1)
Y: MP# in PCB
MPA slave error 39 9C XY F1 Moderate No X: CHA PCB# (*1)
Y: MP# in PCB
Injustice DC voltage control 39 9D X0 F1 Moderate No X: CHA PCB# (*1)
(*38)
Injustice CE MODE (*38) 39 9E X0 F1 Moderate No X: CHA PCB# (*1)
CHT PCB exchange 39 9F X0 F1 Moderate No X: CHA PCB# (*1)
impossible
(4GL ↔ 4GS)
CHA patrol check error 39 C0 XY F1 Service No X: CHA PCB# (*1)
Y: MP# in PCB
CHA Memory Correctable 39 C1 XY F1 Service No X: CHA PCB#
error Y: MP# in PCB
Backup/restore SM 61 00 XX F1 Moderate No XX = 00: Backup failed
Information failed (Hardware factor)
01: Backup failed
(Micro factor)
02: Recovery failed

SIM-RC02-30
Hitachi Proprietary SC01486Z
SIM-RC02-40 DKC515I
Rev.2 / Jul.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor (4/12)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
CHA NAS NAS OS Processor Failure AC 82 X0 F1 Moderate Yes X: CHA PCB# (*44)
OS NAS OS Processor AC 83 X0 F1 Moderate Yes X: CHA PCB# (*44)
Processor Environmental Error
Failure NAS OS failure AC 84 X0 F1 Moderate Yes X: CHA PCB# (*44)
NAS OS failure : Occurrence AC 84 01 F1 Moderate Yes
of a failover or a resource
(failure part not reported)
NAS OS failure : Occurrence AC 84 X2 F1 Moderate Yes X: CHA PCB# (*44)
of a failover
NAS OS failure : Occurrence AC 84 X3 F1 Moderate Yes X: CHA PCB# (*44)
of a LVM_volume failure
NAS OS failure : Occurrence AC 84 X4 F1 Moderate Yes X: CHA PCB# (*44)
of a CLU_partition failure
NAS OS failure : Occurrence AC 84 X5 F1 Moderate Yes X: CHA PCB# (*44)
of a NFS_admin failure
NAS OS failure : Occurrence AC 84 X6 F1 Moderate Yes X: CHA PCB# (*44)
of a File system failure
NAS OS failure : Occurrence AC 84 X7 F1 Moderate Yes X: CHA PCB# (*44)
of a NFS failure
NAS OS failure : Occurrence AC 84 X8 F1 Moderate Yes X: CHA PCB# (*44)
of a IP_address failure
NAS OS failure : Occurrence AC 84 X9 F1 Moderate Yes X: CHA PCB# (*44)
of a CIFS failure
NAS OS failure : Occurrence AC 84 XB F1 Moderate Yes X: CHA PCB# (*44)
of a scripts start failure
NAS OS failure : Occurrence AC 84 XC F1 Moderate Yes X: CHA PCB# (*44)
of a GbENIC LinkDown
NAS OS failure : failover AC 84 XE F1 Moderate Yes X: CHA PCB# (*44)
completed (Failure)
NAS OS failure : failover AC 84 XF F1 Moderate Yes X: CHA PCB# (*44)
completed (Success)
NAS OS Bus failure AC 85 X0 F1 Moderate Yes X: CHA PCB# (*44)
Network Port Failure AC 86 XY F1 Moderate Yes X: CHA PCB# (*44)
Y: PORT# of PCB
NAS OS failure : System AC 87 XY F1 Serious No X: CHA PCB# (*44)
Down Y: Part of failure
(classification)
NAS OS failure : Reduction AC 88 XY F1 Moderate No X: CHA PCB# (*44)
Y: Part of failure
(classification)
NAS OS failure : Alert AC 89 XY F1 Service No X: CHA PCB# (*44)
Y: Part of failure
(classification)

SIM-RC02-40
Hitachi Proprietary SC01486Z
SIM-RC02-50 DKC515I
Rev.2 / Jul.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor (5/12)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
DKA CHK1A threshold over 31 70 XY F1 Service No X: DKA PCB# (*1)
Processor Y: MP# in PCB
error CHK1B threshold over 31 71 XY F1 Service No X: DKA PCB# (*1)
Y: MP# in PCB
CHK3 threshold over 31 72 XY F1 Service No X: DKA PCB# (*1)
Y: MP# in PCB
Processor blocking 31 73 XY F1 Moderate Yes X: DKA PCB# (*1)
Y: MP# in PCB
FM threshold over 31 74 XY F1 Service No X: DKA PCB# (*1)
Y: MP# in PCB
FM error 31 75 XY F1 Moderate Yes X: DKA PCB# (*1)
Y: MP# in PCB
Incorrect SUM value of FM 31 76 XY F1 (*27) No X: DKA PCB# (*1)
Y: MP# in PCB
Processor Memory 31 77 XY F1 Service No X: DKA PCB# (*1)
Temporary Error Y: MP# in PCB
Processor Memory 31 78 XY F1 Service No X: DKA PCB# (*1)
Temporary Error Y: MP# in PCB
(DKF-1 (*55))
Processor Memory 31 88 XY F1 Service No X: DKA PCB# (*1)
Temporary Error Y: MP# in PCB
(DKF-2 (*56))
P/S OFF impossible 3C 8F 00 F1 Moderate No
P/S OFF impossible (Device 3C 9F 00 F1 Moderate No
reserved)
P/S OFF warning (SM 3C C0 00 F1 Moderate No
backup time not assured)
Undefined Package is 3D 90 XY F1 Moderate No X: DKA PCB# (*1,*5)
mounted Y: MP# in PCB
V-R or serial number is 3D 91 XY F1 Moderate No X: DKA PCB# (*1)
inconsistent Y: MP# in PCB
Replace failed 3D 93 XY F1 Moderate No X: DKA PCB# (*1)
Y: MP# in PCB
Micro-program version up 3D 94 X0 F1 Service No X: MP version after
replacing (*23)
Micro-program version up 3D 95 XY F1 Service No X: Present MP version (*23)
impossible Y: reason code (*13)
Warning of SM DISABLE 3D 9A XY F1 Moderate No X: DKA PCB# (*1)
(MPA detected) (*37) Y: 0 = SM Side A Hotline
1 = SM Side B Hotline
SMA slave error 3D 9B XY F1 Moderate No X: DKA PCB# (*1)
Y: MP# in PCB
MPA slave error 3D 9C XY F1 Moderate No X: DKA PCB# (*1)
Y: MP# in PCB
Injustice DC voltage control 3D 9D X0 F1 Moderate No X: DKA PCB# (*1)
(*38)
Injustice CE MODE (*38) 3D 9E X0 F1 Moderate No X: DKA PCB# (*1)

SIM-RC02-50
Hitachi Proprietary SC01486Z
SIM-RC02-51 DKC515I
Rev.2 / Oct.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor (6/12)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
DKA FSW LED BUS test 3D AZ XY FE Moderate No X: DKA PCB# (*1)
Processor Y: FCA# in PCB (*36)
error Z: FSW PCB# (*36)
Tachyon error 3D B0 XY FE Service No X: DKA PCB# (*1)
Y: MP# in PCB
DKA patrol check error 3D C0 XY F1 Service No X: DKA PCB# (*1)
Y: MP# in PCB
DKA Memory Correctable 3D C1 XY F1 Service No X: DKA PCB#
error Y: MP# in PCB
Backup/restore SM 61 00 XX F1 Moderate No XX = 00: Backup failed
Information failed (Hardware factor)
01: Backup failed
(Micro factor)
02: Recovery failed

SIM-RC02-51
Hitachi Proprietary SC01486Z
SIM-RC02-60 DKC515I
Rev.2 / Jul.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor (7/12)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
SHSN error Logical path blockade 32 8Z XY F1 Moderate No X: CHA PCB# (*1,*31)
(CHA Processor) Y: MP# in PCB (*45)
Z: PATH#
0: A0 PATH 4: C0 PATH
1: A1 PATH 5: C1 PATH
2: B0 PATH 6: D0 PATH
3: B1 PATH 7: D1 PATH
Logical path blockade 33 8Z XY F1 Moderate No X: DKA PCB# (*1,*31)
(DKA Processor) Y: MP# in PCB (*45)
Z: PATH#
0: A0 PATH 4: C0 PATH
1: A1 PATH 5: C1 PATH
2: B0 PATH 6: D0 PATH
3: B1 PATH 7: D1 PATH
CHSN error Logical path blockade 32 0Z XY F1 Moderate No X: CHA PCB# (*1,*29)
(CHA-DMA0/CL1-CSW) Y: MP# in PCB (*46)
Z: C path bitmap
Logical path blockade 32 1Z XY F1 Moderate No X: CHA PCB# (*1,*29)
(CHA-DMA0/CL2-CSW) Y: MP# in PCB (*46)
Z: C path bitmap
Logical path blockade 32 2Z XY F1 Moderate No X: DKA PCB# (*1,*29)
(CHA-DMA1/CL1-CSW) Y: MP# in PCB (*46)
Z: C path bitmap
Logical path blockade 32 3Z XY F1 Moderate No X: DKA PCB# (*1,*29)
(CHA-DMA1/CL2-CSW) Y: MP# in PCB (*46)
Z: C path bitmap
Logical path blockade 32 4Z XY F1 Moderate No X: CHA PCB# (*1,*29)
(CHA/PMA/CL1-CSW) Y: MP# in PCB (*46)
Z: C path bitmap
Logical path blockade 32 5Z XY F1 Moderate No X: CHA PCB# (*1,*29)
(CHA/PMA/CL2-CSW) Y: MP# in PCB (*46)
Z: C path bitmap
Logical path blockade 33 0Z XY F1 Moderate No X: DKA PCB# (*1,*29)
(DKA/DRR/CL1-CSW) Y: MP# in PCB (*46)
Z: C path bitmap
Logical path blockade 33 1Z XY F1 Moderate No X: DKA PCB# (*1,*29)
(DKA/DRR/CL2-CSW) Y: MP# in PCB (*46)
Z: C path bitmap
Logical path blockade 33 2Z XY F1 Moderate No X: DKA PCB# (*1,*29)
(DKA/FCA0/CL1-CSW) Y: MP# in PCB (*46)
Z: C path bitmap
Logical path blockade 33 3Z XY F1 Moderate No X: DKA PCB# (*1,*29)
(DKA/FCA0/CL2-CSW) Y: MP# in PCB (*46)
Z: C path bitmap
Logical path blockade 33 4Z XY F1 Moderate No X: DKA PCB# (*1,*29)
(DKA/FCA1/CL1-CSW) Y: MP# in PCB (*46)
Z: C path bitmap

SIM-RC02-60
Hitachi Proprietary SC01486Z
SIM-RC02-70 DKC515I
Rev.2 / Jul.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor (8/12)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
CHSN error Logical path blockade 33 5Z XY F1 Moderate No X: DKA PCB# (*1,*29)
(DKA/FCA1/CL2-CSW) Y: MP# in PCB (*46)
Z: C path bitmap
CHA, CHK2 RCHA temporary error 3F 84 X0 F1 Service No X: CHA PCB# (*1)
(processor) RCHA blocking 3F 85 X0 F1 Serious Yes X: CHA PCB# (*1)
DKA CHK2 Pinned slot CF 4X YY F1 Moderate No X: CU# (*34)
(processor) YY: LDEV#
DRR temporary error CF 80 XY F1 Service No X: DKA PCB# (*1)
Y: MP# in PCB
FCA temporary error CF 81 XY F1 Service No X: DKA PCB# (*1)
Y: Port# (*4)
DRR blocking CF 82 XY F1 Moderate Yes X: DKA PCB# (*1)
Y: MP# in PCB
FCA blocking (0-3) CF 83 XY F1 Moderate Yes X: DKA PCB# (*1)
Y: Port# (*4)
Fibre port blocking (Effect of CF 84 XY F1 Moderate No X: DKA PCB# (*1)
PATH INLINE failed) Y: Port# (*4)
Cache data Pinned slot FF 4X YY F2 Moderate No X: CU#
error YY: LDEV#
Cache error Cache Module Blockade FF C2 YX F2 Service Yes X: PCB# (*1)
Processing end Side A:Even, Side B:Odd
Y: Module group# (*10)
Cache Package Blockade FF C3 0X F2 Service Yes X: PCB# (*1)
Processing End Side A:Even, Side B:Odd
CM/CMA patrol check error FF CC 0X F2 Service No X: PCB# (*1)
Side A:Even, Side B:Odd
Area is volatilized FF CD 0X F2 Service No X: 0 = Side A,1 = Side B
(*2)
(*47)
Package is volatilized FF CE 0X F2 Service No X: PCB# (*1)
Side A:Even, Side B:Odd
Module group is volatilized FF CF YX F2 Service No X: PCB# (*1)
Side A:Even, Side B:Odd
Y: Module group# (*10)
Correctable error FF F0 YX F2 Service No X: PCB# (*1)
Side A:Even, Side B:Odd
Y: Module group# (*10)
Cache temporary error FF F1 YX F2 Service Yes X: PCB# (*1)
Side A:Even, Side B:Odd
Y: Module group# (*10)
Module group blocking FF F2 YX F2 Moderate Yes X: PCB# (*1)
Side A:Even, Side B:Odd
Y: Module group# (*10)
Package blocking FF F3 0X F2 Moderate Yes X: PCB# (*1)
Side A:Even, Side B:Odd
Area blocking FF F4 0X F2 Serious Yes X: 0 = Side A, 1 = Side B
(*2)
Both area failed FF F5 0X F2 Moderate No X: PCB# (*1)
Side A:Even, Side B:Odd

SIM-RC02-70
Hitachi Proprietary SC01486Z
SIM-RC02-80 DKC515I
Rev.3 / Oct.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor (9/12)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
Cache error Injustice DC voltage control FF F6 0X F2 Moderate No X: PCB# (*1)
(*38) Side A:Even, Side B:Odd
Injustice CE MODE (*38) FF F7 0X F2 Moderate No X: PCB# (*1)
Side A:Even, Side B:Odd
CMA Memory Correctable FF F8 0X F2 Service No X: PCB#
error Side A:Even, Side B:Odd
Replace failed (*54) FF F9 0X F2 Serious No X: 0 = Side A, 1 = Side B
(*2)
Module group error in On- FF FD YX F2 Moderate No X: PCB# (*1)
demand area Y: Module group#
Shared SMA patrol check error FF DC 0X F1 Service No X: PCB# (*2)
memory Loss of duplicated FF DE XX F1 Service No XX: Lost information type
error information (*25)
One side Area is volatilized FF DF 0X F1 Service No X: PCB# (*2)
Correctable error FF E0 YX F1 Service No X: PCB# (*2)
Y: Module# (*2,*10)
Package blocking FF E1 0X F1 Moderate No X: PCB# (*2)
Area blocking FF E2 0X F1 Serious Yes X: 0 = Side A, 1 = Side B
(*2,*10)
Real memory size FF E3 XY F1 Serious No X: Number of module
inconsistent (side A)
Y: Number of module
(side B)
(*8)
Replace failed (*20) FF E4 0X F1 Serious No X: PCB# (*2)
Both side invalid FF E5 00 F1 Acute No
Configuration information FF E6 00 F1 Acute No
compare error (*22)
Shared memory is FF E7 00 F1 Serious No
volatilized.
Configuration mismatch FF E8 00 F1 Acute No
“DKCMAIN” micro lost FF E9 00 F1 Serious No (*30)
HPAV micro lost FF E9 01 F1 Serious Yes
Recovery of area blocked FF EA 0X F1 Service Yes X: 0 = Side A, 1 = Side B
temporarily was completed (*2)
CHK3 threshold over FF EC 0X F1 Service No X: PCB# (*2)
Area temporary blocking FF EE 0X F1 Service Yes X: 0 = Side A, 1 = Side B
(*19) (*2)
Rebooted without FF EF 00 F1 Service No
volatilization after an
instantaneous down
Injustice DC voltage control FF D6 0X F1 Service No X: PCB# (*2)
Injustice CE MODE FF D7 0X F1 Service No X: PCB# (*2)
Module error in On-demand FF ED YX F1 Service No X: PCB# (*2)
area Y: Module#

SIM-RC02-80
Hitachi Proprietary SC01486Z
SIM-RC02-90 DKC515I
Rev.3 / Jan.2006, Apr.2006 Copyright © 2005, 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor (10/12)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
Drive error Drive port temporary error DF 6X XX FE Service No XXX: Drive number (*43)
(normal (Drive path: Boundary 0) (*32) (CDEV#:5b+RDEV#:7b)
R/W) Drive port temporary error DF 7X XX FE Service No XXX: Drive number (*43)
(Drive path: Boundary 1) (*32) (CDEV#:5b+RDEV#:7b)
Drive temporary error EF AX XX FE Service No XXX: Drive number (*43)
(*32) (CDEV#:5b+RDEV#:7b)
Drive media error 43 4X XX FF Service No XXX: Drive number (*43)
(*32) (CDEV#:5b+RDEV#:7b)
Drive port blockade DF 8X XX FE Moderate Yes XXX: Drive number (*43)
(Drive path: Boundary 0) (*32) ** (CDEV#:5b+RDEV#:7b)
Drive port blockade DF 9X XX FE Moderate Yes XXX: Drive number (*43)
(Drive path: Boundary 1) (*32) ** (CDEV#:5b+RDEV#:7b)
LDEV blockade DF AX XX FE Serious Yes XXX: Drive number (*43)
(Drive path: Boundary 0/ ** (CDEV#:5b+RDEV#:7b)
Effect of SCSI blockade)
(*15)
LDEV blockade DF BX XX FE Serious Yes XXX: Drive number (*43)
(Drive path: Boundary 1/ ** (CDEV#:5b+RDEV#:7b)
Effect of SCSI blockade)
(*15)
Drive blockade (drive) EF 0X XX FE Serious Yes XXX: Drive number (*43)
(with redundancy) ** (CDEV#:5b+RDEV#:7b)
Drive blockade (drive) EF 1X XX FE Serious Yes XXX: Drive number (*43)
(without redundancy) ** (CDEV#:5b+RDEV#:7b)
Drive blockade (Effect of EF 2X XX FE Service Yes XXX: Drive number (*43)
Dynamic sparing normal ** (CDEV#:5b+RDEV#:7b)
end)
LDEV blockade (Effect of EF 9X XX FE Serious Yes XXX: Drive number (*43)
drive blockade) (*15) ** (CDEV#:5b+RDEV#:7b)
Drive blockade by the EF FF 0X FE Serious No X: DKU position
incorrect set up of a DKU (DKU-R:0, DKU-L:1)
type
Drive blockade (media) 43 BX XX FF Serious Yes XXX: Drive number (*43)
(with redundancy) ** (CDEV#:5b+RDEV#:7b)
Drive blockade (media) 43 CX XX FF Serious Yes XXX: Drive number (*43)
(without redundancy) ** (CDEV#:5b+RDEV#:7b)
Correction copy start (*7) 45 1X XX FE Service Yes XXX: Drive number (*43)
** (CDEV#:5b+RDEV#:7b)
(Source side drive)
Correction copy normal end 45 2X XX FE Service Yes XXX: Drive number (*43)
(*7) ** (CDEV#:5b+RDEV#:7b)
(Source side drive)
Correction copy abnormal 45 3X XX FE Serious Yes XXX: Drive number (*43)
end (*7) ** (CDEV#:5b+RDEV#:7b)
(Source side drive)
Correction copy discontinued 45 4X XX FE Service No XXX: Drive number (*43)
(*7) (CDEV#:5b+RDEV#:7b)
(Source side drive)

SIM-RC02-90
Hitachi Proprietary SC01486Z
SIM-RC02-100 DKC515I
Rev.2 / Jul.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor (11/12)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
Drive error Correction copy warning 45 5X XX FE Service Yes XXX: Drive number (*43)
(normal end* (*7) ** (CDEV#:5b+RDEV#:7b)
R/W) (With blockade LDEV or (Source side drive)
some error)
Dynamic sparing start (*7) 46 1X XX FE Service Yes XXX: Drive number (*43)
(Drive copy) ** (CDEV#:5b+RDEV#:7b)
(Source side drive)
Dynamic sparing normal end 46 2X XX FE Service Yes XXX: Drive number (*43)
(*7) ** (CDEV#:5b+RDEV#:7b)
(Drive copy) (Source side drive)
Dynamic sparing abnormal 46 3X XX FE Moderate Yes XXX: Drive number (*43)
end (Drive copy) (*7) ** (CDEV#:5b+RDEV#:7b)
(Source side drive)
Dynamic sparing 46 4X XX FE Service No XXX: Drive number (*43)
discontinued (*7) (CDEV#:5b+RDEV#:7b)
(Source side drive)
Dynamic sparing warning 46 5X XX FE Service Yes XXX: Drive number (*43)
end* ** (CDEV#:5b+RDEV#:7b)
(With blockade LDEV or (Source side drive)
some error) (Drive copy)
(*7)
Pinned slot EF 4X YY FE Moderate No X: CU#
YY: LDEV#
Drive error Drive temporary error 50 1X XX FE Service No XXX: Drive number (*43)
(ORM) (CDEV#:5b+RDEV#:7b)
Drive media error 50 2X XX FF Service No XXX: Drive number (*43)
(CDEV#:5b+RDEV#:7b)
Drive micro- OEM drive 4A 10 00 FE Service No
program Microprogram exchange start
exchange OEM drive 4A 20 00 FE Service No
(OEM drive) Microprogram exchange
normal end
OEM drive 4A 30 00 FE Service No
Microprogram exchange
abnormal end
OEM drive 4A 40 00 FE Service No
Microprogram exchange
discontinued

*: Warning end : (1) LDEV blockade status is detected, and copy process for the LDEV is
skipped.
(2) Some failures are detected, and copy process is complete.
** : When the drive is 3880 emulation mode, the SIM is not reported to host.
*** : The SIM is not reported to SVP.

SIM-RC02-100
Hitachi Proprietary SC01486Z
SIM-RC02-110 DKC515I
Rev.2 / Jul.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor (12/12)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
Cache Cache Write Pending ratio is 49 10 00 F1 Service No (*53)
Condition over 65%
CSW error Injustice DC voltage control FF 20 0X F1 Moderate No X: CSW PCB# (*1)
(*38)
Injustice CE MODE (*38) FF 21 0X F1 Moderate No X: CSW PCB# (*1)
CARB patrol check error FF 22 0X F1 Service No X: CSW PCB# (*1)
CARB Memory Correctable FF 23 0X F1 Service No X: CSW PCB#
error
SVP Ethernet error for SVP 14 00 X0 F1 Moderate Yes X: CHA PCB# (*1)
interface
error
(CHA side) SIM transfer failure to SVP 14 01 X0 F1 Serious Yes X: CHA PCB# (*1)
SVP Ethernet error for SVP 15 00 X0 F1 Moderate Yes X: DKA PCB# (*1)
interface
error
(DKA side) SIM transfer failure to SVP 15 01 X0 F1 Serious Yes X: DKA PCB# (*1)
Power error HDU power off AC 50 XY F1 Moderate Yes X: DKU number (*12)
Y: HDU number (*12)
HDU power recovered AC 51 XY F1 Service No X: DKU number (*12)
Y: HDU number (*12)
DKC was set to power error AC 60 00 F1 Moderate No
mode
DKC was released from AC 61 00 F1 Service No
power error mode
When DKC was set to power AC 62 00 F1 Service No
error mode, Urgent
Destaging start succeeded.
When DKC was set to power AC 63 00 F1 Moderate No
error mode, Urgent
Destaging start failed.
Power Urgent Destaging start AC 73 00 F1 Moderate No
Power Urgent Destaging AC 74 00 F1 Moderate No
finish
Server error DB Validation error AC 90 00 F1 Serious No (*41)

SIM-RC02-110
Hitachi Proprietary SC01486Z
SIM-RC02-120 DKC515I
Rev.1 / May.2005, Apr.2006 Copyright © 2005, 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor for HRC/HODM (1/2)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
LCP/FCP Logical path(s) on the remote 21 80 XY F1 Moderate Yes X: CHA PCB# (*1)
error copy connections was (*52) Y: PORT# in PCB (*35)
(Remote logically blocked (Due to an
Control error conditions)
Port)
The logical path has been 21 81 XY F1 Service Yes X: CHA PCB# (*1)
recovered from blocked (*52) Y: PORT# in PCB (*35)
condition on the remote copy
conditions.
MCU has received the 21 82 XY F1 Moderate Yes X: CHA PCB# (*1)
notification of (*52) Y: PORT# in PCB (*35)
communication line error
detection from extender.
Pair volume HRC started the initial copy D0 0X YY FE Service Yes X: CU#
status error or out of sync for this (*17) YY:LDEV#
volume.
HRC completed the initial D0 1X YY FE Service Yes X: CU# (*34)
copy for this volume. (*17) YY: LDEV#
HRC for this volume was D0 2X YY FE Service Yes X: CU# (*34)
deleted. (Operation from an (*17) YY: LDEV#
SVP/remote console or a host
processor)
MCU changed volume pair D0 3X YY FE Service No X: CU# (*34)
status. (Operation from an YY: LDEV#
SVP/remote console or a host
processor)
Status of the R-VOL is D1 ZX YY FE Service Yes X: CU# (*34)
changed. (*17) YY: LDEV#
Z: (*16)
RCU changed status of R- D2 0X YY FE Service No X: CU# (*34)
VOL to suspend. (Operation YY: LDEV#
from an SVP/remote console
or a host processor.)
Status of the R-VOL was D2 1X YY FE Service No X: CU# (*34)
changed from suspend to YY: LDEV#
simplex. (Operation from an
SVP/remote console or a host
processor.)
Status of R-VOL was D2 2X YY FE Service No X: CU# (*34)
changed from duplex to YY: LDEV#
simplex. (Operation from an
SVP/remote console or a host
processor.)
Status of the R-VOL was D2 3X YY FE Service No X: CU# (*34)
changed from pendingduplex YY: LDEV#
to simplex. (Operation from
an SVP/remote console or a
host processor.)

SIM-RC02-120
Hitachi Proprietary SC01486Z
SIM-RC02-130 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor for HRC/HODM (2/2)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
Pair volume HODM started the migration D3 0X YY FE Service Yes X: CU# (*34)
status error copy or out of sync for this (*17) YY: LDEV#
volume.
HODM completed the D3 1X YY FE Service Yes X: CU# (*34)
migration copy for this (*17) YY: LDEV#
volume.
HODM for this volume was D3 2X YY FE Service Yes X: CU# (*34)
deleted. (Operation from an (*17) YY: LDEV#
SVP/remote console)
HODM started the erase D3 AX YY FE Service No X: CU# (*34)
operation for the R-VOL. (*17) YY: LDEV#
HODM completed the erase D3 BX YY FE Service No X: CU# (*34)
operation for the R-VOL. (*17) YY: LDEV#
HRC/HODM for this volume D4 0X YY FE Serious Yes X: CU# (*34)
was suspended (Due to an (*17) YY: LDEV#
unrecoverable failure on the
remote copy connections.)
HRC/HODM for this volume D4 1X YY FE Serious Yes X: CU#
was suspended (Due to an (*17) YY: LDEV#
unrecoverable failure on the
M-VOL or the remote copy
connections)
HRC/HODM for this volume D4 2X YY FE Serious Yes X: CU#
was suspended (Due to an (*17) YY: LDEV#
unrecoverable failure on the
R-VOL)
HRC for this volume was D4 3X YY FE Serious Yes X: CU#
suspended (Caused by DFW (*17) YY: LDEV#
to the R-VOL was
prohibited)
HRC for this volume was D4 4X YY FE Serious Yes X: CU#
suspended (Due to an (*17) YY: LDEV#
internal error condition
detected by the RCU)
HRC for this volume was D4 5X YY FE Serious Yes X: CU#
suspended (Caused by Delete (*17) YY: LDEV#
pair operation was issued to
the R-VOL)
Erase operation for this D4 8X YY FE Serious Yes X: CU#
volume was not completed. (*17) YY: LDEV#
(Due to error conditions)
MCU detected a Moderate D4 DX YY FE Moderate Yes X: CU#
Level SIM for RCU. (*18) YY: LDEV#
MCU detected an Acute or D4 EX YY FE Serious Yes X: CU#
Serious Level SIM for RCU. (*18) YY: LDEV#
Status of the M-VOL was not D4 FX YY FE Serious Yes X: CU#
consistent with the R-VOL. (*17) YY: LDEV#

SIM-RC02-130
Hitachi Proprietary SC01486Z
SIM-RC02-140 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor for HRC/HORC (Asynchronous)

(1/2)
Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
Pair volume HRC started the initial copy D5 0X YY FE Service Yes X: CU# (*34)
status error or out of sync for this (*17) YY: LDEV#
volume.
HRC completed the initial D5 1X YY FE Service Yes X: CU# (*34)
copy for this volume. (*17) YY: LDEV#
HRC for this volume was D5 2X YY FE Service Yes X: CU# (*34)
accepted delete pair (*17) YY: LDEV#
operation. (Operation from
an SVP/remote console or a
host processor)
HRC for this volume was D5 3X YY FE Service Yes X: CU# (*34)
accepted suspend pair (*17) YY: LDEV#
operation. (Operation from
an SVP/remote console or a
host processor)
Delete pair operation for this D5 4X YY FE Service Yes X: CU# (*34)
HRC volume has completed. (*17) YY: LDEV#
Suspend pair operation for D5 5X YY FE Service Yes X: CU# (*34)
this HRC volume has (*17) YY: LDEV#
completed.
The R-VOL status has D6 ZX YY FE Service Yes X: CU# (*34)
changed as requested by (*17) YY: LDEV#
MCU. Z: (*16)
The R-VOL has D7 ZX YY FE Service No X: CU# (*34)
accepted/completed state YY: LDEV#
change as requested by Z: (*26)
operation. (Operation from
an SVP/remote console or a
host processor.)
The M-VOL has suspended. DB 0X YY FE Serious Yes X: CU# (*34)
(Due to an unrecoverable (*17) YY: LDEV#
failure on the remote copy
connections.)
The M-VOL has suspended. DB 1X YY FE Serious Yes X: CU# (*34)
(Due to an unrecoverable (*17) YY: LDEV#
failure on the M-VOL or the
remote copy connections)
The M-VOL has suspended. DB 2X YY FE Serious Yes X: CU# (*34)
(Due to an unrecoverable (*17) YY: LDEV#
failure on the R-VOL)
The M-VOL has suspended. DB 3X YY FE Serious Yes X: CU# (*34)
(Caused by DFW to the R- (*17) YY: LDEV#
VOL was prohibited)
The M-VOL has suspended. DB 4X YY FE Serious Yes X: CU# (*34)
(Caused by Suspend pair (*17) YY: LDEV#
operation was issued to the
R-VOL)

SIM-RC02-140
Hitachi Proprietary SC01486Z
SIM-RC02-150 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor for HRC/HORC (Asynchronous)

(2/2)
Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
Pair volume The M-VOL has suspended. DB 5X YY FE Serious Yes X: CU# (*34)
status error (Caused by Delete pair (*17) YY: LDEV#
operation was issued to the
R-VOL)
The R-VOL has suspended. DB 6X YY FE Serious Yes X: CU# (*34)
(Due to an unrecoverable (*17) YY: LDEV#
failure on the remote copy
connections)
The R-VOL has suspended. DB 7X YY FE Serious Yes X: CU# (*34)
(Due to an unrecoverable (*17) YY: LDEV#
failure on the R-VOL)
The R-VOL has suspended. DB 8X YY FE Service No X: CU# (*34)
(Due to an MCU power-off YY: LDEV#
event)
MCU detected a Service DB CX YY FE Service Yes X: CU# (*34)
Level SIM for RCU. YY: LDEV#
MCU detected a Moderate DB DX YY FE Moderate Yes X: CU# (*34)
Level SIM for RCU. YY: LDEV#
MCU detected an Acute or DB EX YY FE Serious Yes X: CU# (*34)
Serious Level SIM for RCU. YY: LDEV#
Status of the M-VOL was not DB FX YY FE Serious Yes X: CU# (*34)
consistent with the R-VOL. (*17) YY: LDEV#

Notice : SIM which REF.CODE is DB7XXX may be reported in the following case.
• When the Suspend Pair operation with the Drain option is accepted by the
MCU/RCU under the host I/O.
• When the Delete Pair operation with the Group option is accepted by the RCU
under the host I/O.

SIM-RC02-150
Hitachi Proprietary SC01486Z
SIM-RC02-160 DKC515I
Rev.2 / Oct.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor for

HMRCF/HOMRCF/HIHSM/HXRC/HRCA (1/1)
Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
HMRCF Copy abnormal end 47 DY XX FE Moderate Yes XX: T-Vol#
error or Y: CU# (*34)
HOMRCF ShadowImage-FlashCopy (R) 4B 0Y XX FE Moderate Yes XX: T-Vol#
error Option abnormal end Y: CU# (*34)
All ShadowImage-FlashCopy 47 E6 00 F1 Moderate Yes
(R) Option abnormal end by
SM volatile
ShadowImage-FlashCopy (R) 4B 2Y XX FE Moderate Yes XX: T-Vol#
version2 Option abnormal Y: CU# (*34)
end
All ShadowImage-FlashCopy 47 E5 00 F1 Moderate Yes
(R) version2 Option
abnormal end by SM volatile
Forcible suspend by SM 47 E7 00 FE Moderate Yes
volatile
System Option MODE80 and 47 E0 00 FE Moderate No
HMRCF/HOMRCF settings
are inconsistent.
HIHSM HIHSM Volume Migration 47 FY XX FE Moderate No XX: S-Vol#
error Abnormal End Y: CU# (*34)
HXRC/ Sidefile ‘sleep wait’ 49 0X YY FE Service Yes X: CU# (*34)
HRCA error threshold over YY: LDEV#
SVP MODE 118 ON:
Generate SIM
Hi-Copy Copy abnormal end 4B 1Y XX FE Moderate Yes XX: S-Vol#
error Y: CU#

SIM Reference Codes Detected by the Processor for Pool (1/1)

Error REF CODE SIM Level of Host Corresponding to Remarks
22 23 13 28 error report complete from
WebCon
Pool error Pool utilization60 00 XX F1 Moderate Yes Yes XX: Pool #
threshold excess
Pool blocking 60 01 XX F1 Moderate Yes Yes XX: 00∼7F: Pool #
FF: SM Full

SIM-RC02-160
Hitachi Proprietary SC01486Z
SIM-RC02-170 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor for DCR (1/1)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
DCR Status PreStaging abnormal end 48 21 XX FE Service No XX: Reason code (*11)

SIM-RC02-170
Hitachi Proprietary SC01486Z
SIM-RC02-180 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

SIM Reference Codes Detected by the Processor for External Subsystem

Connection (1/1)
Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
External External Subsystem 21 D0 XY F1 Moderate Yes X:CHA PCB# (*1)
Subsystem Connection Path Failure Y:PORT# in PCB (*35)
Connection (*42)
External Subsystem 21 D1 XY F1 Service No X:CHA PCB# (*1)
Connection Path recovery Y:PORT# in PCB (*35)
(*42)
External Subsystem path 21 D2 XY F1 Service Yes X:CHA PCB# (*1)
response time out threshold Y:PORT# in PCB (*35)
over (*42)
External Subsystem Device EF D0 00 FE Serious Yes (*42)
failure

SIM-RC02-180
Hitachi Proprietary SC01486Z
SIM-RC02-190 DKC515I
Rev.2 / Jan.2006, Apr.2006 Copyright © 2005, 2006, Hitachi, Ltd.

List of Reference Codes of SIMs Detected by UR Processor (1/2)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
LCP/FCP The remote copy logical path 21 80 XY F1 Moderate Yes X:CHA PCB# (*1)
failure was blockaded (owing to a (*52) Y:PORT# in PCB (*35)
(Remote failure). (*33)
control port) Recovery of the remote copy 21 81 XY F1 Service No X:CHA PCB# (*1)
logical path Y: PORT# in PCB (*35)
Reception of a line failure 21 82 XY F1 Moderate Yes X:CHA PCB# (*1)
notice from the extender (*52) Y: PORT# in PCB (*35)
Pair volume A volume to be used by the D8 0X YY FE Service Yes X:CU# (*34)
failure UR was defined (*57) YY:LDEV#
The volume being used by D8 1X YY FE Service Yes X:CU# (*34)
the UR began a copying (*57) YY:LDEV#
The volume being used by D8 2X YY FE Service Yes X:CU# (*34)
the UR completed a copying (*57) YY:LDEV#
The volume being used by D8 3X YY FE Service Yes X:CU# (*34)
the UR received a request for (*57) YY:LDEV#
suspension
The volume being used by D8 4X YY FE Service Yes X:CU# (*34)
the UR completed a (*57) YY:LDEV#
suspension transaction
The volume being used by D8 5X YY FE Service Yes X:CU# (*34)
the UR received a request for (*57) YY:LDEV#
deletion
The volume being used by D8 6X YY FE Service Yes X:CU# (*34)
the UR completed the (*57) YY:LDEV#
deletion
The volume being used by D8 7X YY FE Service Yes X:CU# (*34)
the UR was defined (*57) YY:LDEV#
(placed in the PSUS status
immediately)
A change to an SVOL was D9 ZX YY FE Service Yes X:CU# (*34)
received from the MCU (*57) YY:LDEV#
Z: (*50)
A change to an SVOL was DA ZX YY FE Service No X:CU# (*34)
received from the RCU YY:LDEV#
Z: (*51)

SIM-RC02-190
Hitachi Proprietary SC01486Z
SIM-RC02-200 DKC515I
Rev.4 / Apr.2006, Jun.2006 Copyright © 2005, 2006, Hitachi, Ltd.

List of Reference Codes of SIMs Detected by UR Processor (2/2)

Error REF CODE SIM Level of Host Remarks
22 23 13 28 error report
Pair volume A volume being used by a DC 0X YY FE Serious Yes X:CU# (*34)
failure P-VOL was suspended (*57) YY:LDEV#
(Path recovery was
impossible)
A volume being used by a DC 1X YY FE Serious Yes X:CU# (*34)
P-VOL was suspended (*57) YY:LDEV#
(A failure on the MCU side
was detected)
A volume being used by a DC 4X YY FE Serious Yes X:CU# (*34)
P-VOL was suspended (*57) YY:LDEV#
(Suspension of an S-VOL
was detected)
A volume being used by a DC 5X YY FE Serious Yes X:CU# (*34)
P-VOL was suspended (*57) YY:LDEV#
(Deletion of an S-VOL pair
was detected)
A volume being used by an DC 6X YY FE Serious Yes X:CU# (*34)
S-VOL was suspended (*57) YY:LDEV#
(Path recovery was
impossible)
A volume being used by an DC 7X YY FE Serious Yes X:CU# (*34)
S-VOL was suspended (*57) YY:LDEV#
(A failure on the RCU side
was detected)
A volume being used by an DC 8X YY FE Service No X:CU# (*34)
S-VOL was suspended YY:LDEV#
(P/S OFF on the MCU side
was detected)
UR M-JNL Meta overflow DC E0 AA FE Moderate No AA:JNLG#
warning
UR M-JNL Data overflow DC E1 AA FE Moderate No AA:JNLG#
warning
UR R-JNL Meta overflow DC E2 AA FE Moderate No AA:JNLG#
warning
UR R-JNL Data overflow DC E3 AA FE Moderate No AA:JNLG#
warning
The UR Read JNL was DC F0 AA FE Moderate No AA:JNLG#
interrupted

SIM-RC02-200
Hitachi Proprietary SC01486Z
SIM-RC02-210 DKC515I
Rev.2 / Jun.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

(*1)
CHA PCB#: x‘4’ (Slot 1A), x‘5’ (Slot 1B), x‘c’ (Slot 2F), x‘d’ (Slot 2E) indicates the CHA
PCB number. See the figure below.
DKA PCB#: x‘0’ (Slot 1A) x‘4’ (Slot 2F) indicates the DKA PCB number. See the figure
below.
CSW PCB#: x‘0’ to x‘1’ indicates the CSW PCB number. See the figure below.
Cache PCB#: x‘0’ to x‘1’ indicates the Cache PCB number. See the figure below.
SM PCB#: x‘0’ to x‘1’ indicates the SM PCB number. See the figure below.

(*2) Side A/B: Indicates the side of cache/shared memory. See the figure below.

Boundary 0 (cluster 1) Boundary 1 (cluster 2)

Side A Side B

MIX/ CHA BASE BASE CHA MIX/

CHA (CSW0 + (CSW1 + CHA
SM0 + SM1 +
Cache0) Cache1)
1A 1B 1C 2D 2E 2F

MP# in PCB 0~7 0~7 0~7 0~7

CHA PCB# 4 5 d c
DKA PCB# 0 4
SM PCB# 0 1
Cache PCB# 0 1
CSW PCB# 0 1

SIM-RC02-210
Hitachi Proprietary SC01486Z
SIM-RC02-220 DKC515I
Rev.1 / May.2005, Jun.2005 Copyright © 2005, Hitachi, Ltd.

(*3)
LCP #1: x‘0’ to x‘7’ indicates the LCP number.
LCP #2: x‘8’ to x‘F’ indicates the LCP number.

LCP LCP LCP LCP LCP LCP LCP LCP

LCP#1 0 1 2 3 4 5 6 7
LCP#2 C C D D E E F F

CHP CHP CHP CHP CHP CHP CHP CHP

0 1 2 3 4 5 6 7

CHA-1B/CHA-2E

SIM-RC02-220
Hitachi Proprietary SC01486Z
SIM-RC02-230 DKC515I
Rev.1 / May.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

(*4) Port #: x‘0’ to x‘3’ indicates the FIBRE port number. See the figure below.

DKA

FCA4 FCA5 FCA6 FCA7  FCA# in DKA PCB

0 1 2 3  Number of byte 13 (bit 4-7)
Fibre-xx0 Fibre-xx2 Fibre-xx1 Fibre-xx3  Fibre port#

(*5) The package that is not defined in the configuration information exists.
If it is prepared for new installation, it is necessary to do the new installation procedure.
Otherwise it should be pulled out by executing P/S off.

(*7) Isolate the error according to the procedure shown in TRBL05-210.

(*8) Recover the error according to the procedure shown in TRBL05-360.

(*10) Perform error isolation according to the procedure given in the two separate pages attached to
TRBL05-390.
Refer to LOC02-40 and check the DIMM replacement position.

(*11) Reason Code

x‘E1’, x‘10’: No DCR PP
x‘E2’, x‘20’: Subsystem busy
x‘E4’, x‘40’: Staging time over
x‘E5’, x‘50’: Cache or SM blockade
x‘E6’, x‘60’: LDEV Warning
x‘E7’, x‘70’: Staging failure
x‘E8’, x‘80’: P/S OFF
x‘90’: PreStaging canceled
x‘EA’, x‘a0’: Cache over loaded
x‘EB’, x‘b0’: Some MP’s blockade

SIM-RC02-230
Hitachi Proprietary SC01486Z
SIM-RC02-240 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*12) DKU#: x‘0’ to x‘4’ indicates DKU-RK number. See the figure below.
HDU#: x‘0’ to x‘3’ indicates HDU number. See the figure below.

DKU-RK0 DKU-RK1 DKU-RK2 DKU-RK3

DKU# 0 1 2 3

HDU#3 HDU#3 HDU#3 HDU#3

HDU#2 HDU#2 HDU#2 HDU#2

HDU#1 HDU#1 HDU#1 HDU#1

HDU#0 HDU#0 HDU#0 HDU#0

(*13) reason code

x‘0’: Pinned data exist
x‘1’: The shutdown of the power supply was occurred
x‘2’: Invalid Version/Revision exists

(*15) Recover LDEVs according to the procedure shown in TRBL05-420.

(*16) Change pair status number

x‘0’: From simplex to duplex pending
x‘1’: From simplex to duplex
x‘2’: From pending duplex to duplex
x‘3’: From pending duplex to suspend
x‘4’: From duplex to suspend
x‘5’: From duplex to simplex
x‘6’: From pending duplex to simplex
x‘7’: From suspend to simplex
x‘8’: From suspend to duplex pending

SIM-RC02-240
Hitachi Proprietary SC01486Z
SIM-RC02-250 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*17) You can suppress reporting the HRC/HODM Service SIM to the HOST by RCU Option
operation (PPRC support by HOST and Service SIM of HRC/HODM).

• Service level SIM

PPRC support by Service SIM or level of error HRC HODM
HOST HRC/HODM
Report DKC_SIM Host Report Host Report
Yes DEV_SIM Not Host Report Host Report
Not Report DKC_SIM Not Host Report Not Host Report
DEV_SIM Not Host Report Not Host Report
Report DKC_SIM Host Report Host Report
No DEV_SIM Host Report Host Report
Not Report DKC_SIM Not Host Report Not Host Report
DEV_SIM Not Host Report Not Host Report

• Moderate or Serious level SIM

PPRC support by level of error HRC HODM
HOST
Yes DKC_SIM Host Report Host Report
DEV_SIM Not Host Report Host Report
No DKC_SIM Host Report Host Report
DEV_SIM Host Report Host Report

(*18) SIMs which REF.CODE are D4DX, D4EX are reported in case of HODM.
In case of HRC, SIMs reported from RCU are reported to the host by MCU.
Severity Level RC of reported SIM for HRC RC of reported SIM for HODM
Acute or Serious No modification D4EX
Moderate No modification D4DX
Service (Not HRC SIM) No modification Not reported
Service (HRC SIM) Not reported Not reported

(*19) This temporary blocking is to recover the logical table on SM and be automatically recovered.

(*20) In case of the replacement of the BASE PCB on the side having blocked SM (see
REP01-270 work ID = RCA1), insert the removed BASE PCB again.

(*22) The LDEV is blocked because of an error (inconsistency between data on the A and B sides)
of configuration information stored in the SM. Recover the error following the instruction of
the Technical Support Division.

SIM-RC02-250
Hitachi Proprietary SC01486Z
SIM-RC02-260 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*23) X represents the X in a program version “?X-??-??/??”.

(*24) Cache SIMM sizes of sides A and B are different because the replacement of the cache
memory has been performed on one side only. Perform the replacement left referring to the
description in the remark column.

(*25) Type of the lost information is reported according to the bit position. (There may be the case
that two or more bits are set.)

(*26) Change pair status number

x‘0’: Accepted Suspend Pair operation
x‘1’: Accepted Delete Pair operation (The R-VOL is in suspended status)
x‘2’: Accepted Delete Pair operation (The R-VOL is in duplex status)
x‘3’: Accepted Delete Pair operation (The R-VOL is in pending duplex status)
x‘4’: Completed Suspend Pair operation
x‘5’: Completed Delete Pair operation

(*27) In the case that the error is detected in the area of ROM, the level of error is “Moderate” in
other case “Service”.

SIM-RC02-260
Hitachi Proprietary SC01486Z
SIM-RC02-270 DKC515I
Rev.1 / May.2005, Jul.2005 Copyright © 2005, Hitachi, Ltd.

(*29) C path bitmap indicates status of C path. See the figure below.

Byte 23 (Lower 8bit)

C0 or C1 path 0: normal
1: blocade
C2 or C3 path

CHSN Logical path layout

CHA/MIX CHA CHA/MIX CHA
1A 1B 2F 2E

BASE-1C (CL1-CSW) BASE-2D (CL2-CSW)

Path C0 C1 C2 C3 C0 C1 C2 C3
number

BASE-1C (CL1-Cache) BASE-2D (CL2-Cache)

SIM-RC02-270
Hitachi Proprietary SC01486Z
SIM-RC02-280 DKC515I
Rev.1 / May.2005, Jul.2005 Copyright © 2005, Hitachi, Ltd.

(*30) If this reference code is reported, execute the micro-program exchange procedure (On-line) of
the micro type “DKCMAIN”. (MICRO-FC04-10 to 04-150)

(*31) PATH# A0, A1, B0, B1 indicates the SHSN Logical path number. See the figure below.
SHSN Logical path layout
CHA/MIX CHA CHA/MIX CHA
1A 1B 2F 2E

Path
number A0 A1 B0 B1
BASE-1C (CL1-SM) BASE-2D (CL2-SM)

(*32) In the case that there are no redundancy of drive the level of error is “Serious”.

(*33) In the fibre channel connection of the HORC, this SIM may be issued on the MCU side when
the microprogram of the RCU is replaced.

(*34) CU# is detected only lower figure in SIM-RC. (CU# 0x0 ~ 0xF)
Look at the SVP information - Content SIM - Error Location.

SIM-RC02-280
Hitachi Proprietary SC01486Z
SIM-RC02-290 DKC515I
Rev.1 / May.2005, Jul.2005 Copyright © 2005, Hitachi, Ltd.

(*35) PORT#: x‘0’ to x‘F’ in PCB indicates the PORT number in CHA PCB. See the table below.

CL1 CL2
Port# 1B 1A 2F 2E
0 CL1-E CL1-A CL2-A CL2-E
1 CL3-E CL3-A CL4-A CL4-E
2 CL5-E CL5-A CL6-A CL6-E
3 CL7-E CL7-A CL8-A CL8-E
4 CL1-F CL1-B CL2-B CL2-F
5 CL3-F CL3-B CL4-B CL4-F
6 CL5-F CL5-B CL6-B CL6-F
7 CL7-F CL7-B CL8-B CL8-F
8 CL1-G CL2-G
9 CL3-G CL4-G
A CL5-G CL6-G
B CL7-G CL8-G
C CL1-H CL2-H
D CL3-H CL4-H
E CL5-H CL6-H
F CL7-H CL8-H

SIM-RC02-290
Hitachi Proprietary SC01486Z
SIM-RC02-300 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*36) Each one of the FSW PCB# z‘0’ to z‘3’ denotes an FSW number corresponding to each PCB#
or MP# in the PCB.
See the table below.

FSW PCB#
PCB# FCA# FSW#0 FW#1 FSW#2 FSW#3
MIX-1A 4 FSW001-L FSW101-L FSW201-L FSW301-L
5 FSW023-L FSW123-L FSW223-L FSW323-L
6 FSW001-L FSW101-L FSW201-L FSW301-L
7 FSW023-L FSW123-L FSW223-L FSW323-L
MIX-2F 4 FSW001-U FSW101-U FSW201-U FSW301-U
5 FSW023-U FSW123-U FSW223-U FSW323-U
6 FSW001-U FSW101-U FSW201-U FSW301-U
7 FSW023-U FSW123-U FSW223-U FSW323-U

PCB type 4MP PK 2MP

FCA#
4 4 4
5 5 4
6 6 5
7 7 5

SIM-RC02-300
Hitachi Proprietary SC01486Z
SIM-RC02-310 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*37) Recover the error according to the procedure shown in TRBL05-580.

(*38) Recover the error according to the procedure shown in TRBL05-590.

(*39) If this reference code is reported, please conform as shown below.

1. Setting topology
2. HBA/SWITCH (supported or not)

(*40) See the figure below about HTP path number.

CHA PCB

HTP# 0 HTP# 1 HTP# 2 HTP# 3

Path
number

0 1 2 3 4 5 6 7 8 9 A B C D E F
MP MP MP MP MP MP MP MP
0 1 2 3 4 5 6 7

SIM-RC02-310
Hitachi Proprietary SC01486Z
SIM-RC02-320 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*41) The following information of SIM = AC90 is valid.

0 1 2 3 4 5 6 7
byte40
Port number (Eg. CL1-0=0, CL1-B=1)
byte41
byte42
LDEV number
byte43
byte44
byte45
Starting LBA address of CDB
byte46
byte47
byte48
Transfer Length of CDB
byte49
byte4A
byte4B
byte4C
byte4D
World Wide Name (WWN) of the host which issued the write request
byte4E
byte4F
byte50
byte51
byte52 Detected error item(s). Bit-OR of the left items.
Check kind
0x01: Check-F1
0x02: Check-L
0x04: Check-F2
0x08: Check-F3
byte53
~ Not used
byte7F

SIM-RC02-320
Hitachi Proprietary SC01486Z
SIM-RC02-330 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*42) The following information of SIM = 21D0, 21D1, 21D2, EFD0 is valid.

0 1 2 3 4 5 6 7
byte40 Port number
byte41 (Eg. CL1-A=0, CL1-B=1)
byte42
LDEV number
byte43
byte44
~ VDEV number
byte47
byte48
~ Forehand WWN of External Storage connection
byte4F
byte50
~ Product Number of External Storage
byte59
byte5A
~ Vendor Name
byte61
byte62
~ Model name of External Storage
byte71
byte72
External LUN#
byte73
byte74
Loss of Signal Count
byte75
byte76
Bad Received Character Count
byte77
byte78
Loss of Synchronization Count
byte79
byte7A
Received EOFa Count
byte7B
byte7C
Discarded Frame Count
byte7D
byte7E
Bad_CRC Count
byte7F

The case of vendor name “HP” and model name of external storage “MSA”, product number of
external storage is binary form.

SIM-RC02-330
Hitachi Proprietary SC01486Z
SIM-RC02-340 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*43) Drive number XXX indicates the CDEV# / RDEV#. See the table below.

Byte 23 (8bit) Byte 13 (8bit)

CDEV# (5bit) RDEV# (7bit)

Refer to “Physical-Logical Device Matrixes” from THEORY05-10 for CDEV# / RDEV# (C/R#)-
Disk Drive Number correspondence.

Eg.) For SIM-RC EF13-97.

Byte 23 (8bit) Byte 13 (8bit)

0 0 0 1 0 0 1 1 1 0 0 1 0 1 1 1
CDEV# (5bit) RDEV# (7bit)
=3 =17

SIM-RC02-340
Hitachi Proprietary SC01486Z
SIM-RC02-350 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

CDEV
0x00 0x01 0x02 0x03
RDEV 0x00 000 080 100 180
0x01 001 081 101 181
0x02 002 082 102 182
0x03 003 083 103 183
0x04 004 084 104 184
0x05 005 085 105 185
0x06 006 086 106 186
0x07 007 087 107 187
0x08 008 088 108 188
0x09 009 089 109 189
0x0A 00A 08A 10A 18A
0x0B 00B 08B 10B 18B
0x0C 00C 08C 10C 18C
0x0D 00D 08D 10D 18D
0x0E 00E 08E 10E 18E
0x0F 00F 08F 10F 18F
0x10 010 090 110 190
0x11 011 091 111 191
0x12 012 092 112 192
0x13 013 093 113 193
0x14 014 094 114 194
0x15 015 095 115 195
0x16 016 096 116 196
0x17 017 097 117 197
0x18 018 098 118 198
0x19 019 099 119 199
0x1A 01A 09A 11A 19A
0x1B 01B 09B 11B 19B
0x1C 01C 09C 11C 19C
0x1D 01D 09D 11D 19D
0x1E 01E 09E 11E 19E
0x1F 01F 09F 11F 19F

SIM-RC02-350
Hitachi Proprietary SC01486Z
SIM-RC02-360 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

CDEV
0x00 0x01 0x02 0x03
RDEV 0x20 020 0A0 120 1A0
0x21 021 0A1 121 1A1
0x22 022 0A2 122 1A2
0x23 023 0A3 123 1A3
0x24 024 0A4 124 1A4
0x25 025 0A5 125 1A5
0x26 026 0A6 126 1A6
0x27 027 0A7 127 1A7
0x28 028 0A8 128 1A8
0x29 029 0A9 129 1A9
0x2A 02A 0AA 12A 1AA
0x2B 02B 0AB 12B 1AB
0x2C 02C 0AC 12C 1AC
0x2D 02D 0AD 12D 1AD
0x2E 02E 0AE 12E 1AE
0x2F 02F 0AF 12F 1AF
0x30 030 0B0 130 1B0
0x31 031 0B1 131 1B1
0x32 032 0B2 132 1B2
0x33 033 0B3 133 1B3
0x34 034 0B4 134 1B4
0x35 035 0B5 135 1B5
0x36 036 0B6 136 1B6
0x37 037 0B7 137 1B7
0x38 038 0B8 138 1B8
0x39 039 0B9 139 1B9
0x3A 03A 0BA 13A 1BA
0x3B 03B 0BB 13B 1BB
0x3C 03C 0BC 13C 1BC
0x3D 03D 0BD 13D 1BD
0x3E 03E 0BE 13E 1BE

SIM-RC02-360
Hitachi Proprietary SC01486Z
SIM-RC02-370 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*44) For CHA NAS OS Processor Failure SIM, perform troubleshoot procedures indicated in “7.4
Troubleshooting Procedures” [NAS07-210] in NAS Software Section.

(*45) SM blocked SIMs (RC = FFE2-0x or FFZ1-0x) reported at the same time, have priority over
this SIM. If SHSN path status return to “normal” after those recovery action, complete this
SIM together.

(*46) CACHE blocked SIMs (RC = FFF4-0x or FFF3-0x) reported at the same time, have priority
over this SIM. If CHSN path status return to “normal” after those recovery action, complete
this SIM together.

SIM-RC02-370
Hitachi Proprietary SC01486Z
SIM-RC02-380 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*47) In case of PS/OFF (normal end), the battery backup to CM will be blocked since the battery
backup to SM will be prioritized.
In case of PS/ON, the SIM may be reported according to the SM/CM status; if it is definitely
caused by the backup blocking as above, please ignore the location that the SIM has indicated.

(*48) SIM = 2194 is valid

0 1 2 3 4 5 6 7
Byte40
0x0000B6AF (Related SSB Code)
Byte43
Byte44
SIM type + Port#
Byte47
Byte48
Starting supervise at time
Byte4B
Byte4C
Starting supervise at MIC_H timer
Byte4F
Byte50
SSB reported count (Comprehensive value)
Byte53
Byte54
Link Failure supervised timer SVP timer
Byte57
Byte58
Link Failure supervised timer (0.96µsec/count)
Byte5B
Byte5C
SSB: B65A reported count
Byte5F
Byte60
SSB: B65C reported count
Byte63
Byte64
SSB: B65D reported count
Byte67
Byte68
SSB: B65E reported count
Byte6B
Byte6C
SSB: B660 reported count
Byte6F
Byte70
SSB: B661 reported count
Byte73
Byte74
SSB: B668 reported count
Byte77
Byte78
SSB: B66A reported count
Byte7B
Byte7C
SSB: DDA1 reported count
Byte7F

SIM-RC02-380
Hitachi Proprietary SC01486Z
SIM-RC02-390 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*49) SIM = 2193 is valid

0 1 2 3 4 5 6 7
Byte40
0x0000B6AF (Related SSB Code)
Byte43
Byte44
SIM type + Port#
Byte47
Byte48
Loss of Signal Counter (Cumulative value for 30 min to before the reporting SIM)
Byte4B
Byte4C
Bad Received Character Counter (Cumulative value for 30 min to before the reporting SIM)
Byte4F
Byte50
Loss of Sync Counter (Cumulative value for 30 min to before the reporting SIM)
Byte53
Byte54
Link Failure Counter (Cumulative value for 30 min to before the reporting SIM)
Byte57
Byte58
Discarded Frame Counter (Cumulative value for 30 min to before the reporting SIM)
Byte5B
Byte5C
Received _EOFa Counter (Cumulative value for 30 min to before the reporting SIM)
Byte5F
Byte60
BAD_CRC Counter (Cumulative value for 30 min to before the reporting SIM)
Byte63
Byte64
OLS/NOS Received Counter (Cumulative value for 30 min to before the reporting SIM)
Byte67
Byte68
LIPf Received Counter (Cumulative value for 30 min to before the reporting SIM)
Byte6B
Byte6C
Bad_ALPA Counter (Cumulative value for 30 min to before the reporting SIM)
Byte6F
Byte70
Link Down detected Counter (Cumulative value for 30 min to before the reporting SIM)
Byte73
Byte74
none
Byte77
Byte78
none
Byte7B
Byte7C
none
Byte7F

SIM-RC02-390
Hitachi Proprietary SC01486Z
SIM-RC02-400 DKC515I
Rev.3 / Jan.2006, Apr.2006 Copyright © 2005, 2006, Hitachi, Ltd.

(*50) Numbers of pair status changes

x‘0’: From Simplex to Duplex Pending
x‘1’: From Simplex to Duplex
x‘2’: From Duplex Pending to Duplex
x‘3’: From Duplex Pending to Suspend
x‘4’: From Duplex to Suspend
x‘5’: From Duplex to Simplex
x‘6’: From Duplex Pending to Simplex
x‘7’: From Suspend to Simplex
x‘8’: From Suspend to Duplex Pending
x‘C’: From Simplex to Suspend

(*51) Numbers of pair status changes

x‘0’: A request for suspension was received.
x‘1’: A suspension transaction was completed.
x‘2’: An instruction to delete a pair was received in the Suspend status.
x‘3’: An instruction to delete a pair was received in the Duplex Pending status.
x‘4’: An instruction to delete a pair was received in the Duplex status.
x‘5’: A pair deletion was completed.

(*52) The DKC emulation type determines whether the SIM will be reported to the host, as
explained below;
• DKC emulation type is 2105 or 2107
You can select the SIM report to the HOST by SYSTEM OPTION.
MODE308 = OFF (Default) : Not Report to the HOST
MODE308 = ON : Report to the HOST
(However, ‘*17’ is higher priority than ‘*52’)
• Others
It is decided by setting ‘*17’.

(*53) Contact T.S.D with dump collected by Auto Dump in type “Detail”.

(*54) Concerned SIM when abnormality occurs in CACHE memory when the BASE P/K
replacement recovers, it is output SIM. When SIM is output, the replacement of BASE P/K is
executed in another service parts.

(*55) Error occurred in normal processing.

(*56) Error occurred in interrupting.

(*57) You can suppress reporting the SIM to the optional operation.
Default is “not report”.

SIM-RC02-400
Hitachi Proprietary SC01486Z
SIM-RC02-410 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

2.2 SIM Reference Codes Detected by the SVP

SIM-RC02-410
Hitachi Proprietary SC01486Z
SIM-RC02-420 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

Error REF code SIM Level of Host Remarks

22 23 13 28 error report
Environmental Back of cabinet BF 10 10 F1 Moderate Yes
error Left Side
Temperature (TH1 detect)
Abnormal Alarm Back of cabinet BF 10 11 F1 Moderate Yes
Right Side
(TH12 detect)
Back of cabinet BF 12 10 F1 Moderate Yes
Left Side
Temperature (TH1 detect)
Abnormal Warning Back of cabinet BF 12 11 F1 Moderate Yes
Right Side
(TH2 detect)
Voltage alarm Cluster-1 BF 20 10 F1 Moderate Yes
Cluster-2 BF 20 11 F1 Moderate Yes
ACDC alarm BF 22 XX F1 Moderate Yes
(*1)
Voltage warning DKCMN1 BF 31 10 F1 Moderate Yes
DKCMN2 BF 31 11 F1 Moderate Yes
PS11 BF 40 10 F1 Moderate Yes
PS21 BF 40 11 F1 Moderate Yes
PS12 BF 41 10 F1 Moderate Yes
P/S warning PS22 BF 41 11 F1 Moderate Yes
PS0 Warning BF 4A XX F1 Moderate Yes
(*1)
PS1 Warning BF 4B XX F1 Moderate Yes
(*1)
48V Voltage fall 1 BF 4E XX F1 Moderate Yes
HDD-PL 48V (*1)
Voltage fall 48V Voltage fall 2 BF 4F XX F1 Moderate Yes
(*1)
BATTERY-11 BF 50 10 F1 Moderate Yes
BATTERY-21 BF 50 11 F1 Moderate Yes
Battery warning BATTERY-12 BF 51 10 F1 Moderate Yes
BATTERY-22 BF 51 11 F1 Moderate Yes
BATTERY-13 BF 52 10 F1 Moderate Yes
BATTERY-23 BF 52 11 F1 Moderate Yes
AC warning Cluster-1 BF 60 E0 F1 Moderate Yes
(1-phase) Cluster-2 BF 60 E1 F1 Moderate Yes

SIM-RC02-420
Hitachi Proprietary SC01486Z
SIM-RC02-430 DKC515I
Rev.1 / May.2005, Oct.2005 Copyright © 2005, Hitachi, Ltd.

Error REF code SIM Level of Host Remarks

22 23 13 28 error report
Environmental FFAN1 BF 70 10 F1 Moderate Yes
(FFAN11)
error FFAN2 BF 70 11 F1 Moderate Yes
(FFAN21)
FFAN1 BF 71 10 F1 Moderate Yes
(FFAN12)
FFAN2 BF 71 11 F1 Moderate Yes
(FFAN22)
RFAN1 BF 72 10 F1 Moderate Yes
(RFAN11)
Fan abnormality RFAN2 BF 72 11 F1 Moderate Yes
(RFAN21)
FAN Warning1 BF 72 XX F1 Moderate Yes
(*1)
RFAN1 BF 73 10 F1 Moderate Yes
(RFAN12)
RFAN2 BF 73 11 F1 Moderate Yes
(RFAN22)
FAN Warning2 BF 73 XX F1 Moderate Yes
(*1)
JP remains DKC Alarm BF 81 A3 F1 Moderate Yes
SVP PS ON/OFF BF 85 A2 F1 Moderate Yes
Environment Environment SSVP/MN BF 90 A0 F1 Moderate No
Monitor monitor (DKCMN1 detect)
failure error (Access error) SSVP/MN BF 90 A1 F1 Moderate No
(DKCMN2 detect)
Environment monitor error (Busy) BF 91 A2 F1 Moderate No
SSVP/MN BF 92 A0 F1 Moderate No
Environment (DKCMN1 detect)
monitor DIAG SSVP/MN BF 92 A1 F1 Moderate No
setting error (DKCMN2 detect)
SSVP/MN BF 92 A2 F1 Moderate No
(SSVP P/K detect)
SSVP/MN BF 93 A0 F1 Moderate No
CEINH Register (DKCMN1 detect)
error SSVP/MN BF 93 A1 F1 Moderate No
(DKCMN2 detect)
Cluster 1 BF 94 XX F1 Moderate No
FSW Access error (*1)
Cluster 2 BF 95 XX F1 Moderate No
(*1)
Cluster 1 BF 98 XX F1 Moderate No
PS ON error (*1)
Cluster 2 BF 99 XX F1 Moderate No
(*1)
SSVP/MN BF 9A A0 F1 Moderate No
Environment (DKCMN1 detect)
monitor PCB error SSVP/MN BF 9A A1 F1 Moderate No
(DKCMN2 detect)

SIM-RC02-430
Hitachi Proprietary SC01486Z
SIM-RC02-440 DKC515I
Rev.1 / May.2005, Apr.2006 Copyright © 2005, 2006, Hitachi, Ltd.

Error REF code SIM Level of Host Remarks

22 23 13 28 error report
Environment SSVP/MN BF A0 A0 F1 Moderate No
Monitor Alarm disagreement (DKCMN1 detect)
failure
SSVP/MN BF A0 A1 F1 Moderate No
(DKCMN2 detect)
SSVP/MN BF A1 A0 F1 Moderate No
P/S On disagreement (DKCMN1 detect)
SSVP/MN BF A1 A1 F1 Moderate No
(DKCMN2 detect)
SSVP/MN BF A2 A0 F1 Moderate No
P/S Off (DKCMN1 detect)
disagreement SSVP/MN BF A2 A1 F1 Moderate No
(DKCMN2 detect)
MIX PCB- BF A0 XX F1 Moderate No
Cluster 1 (*1)
MIX PCB- BF A1 XX F1 Moderate No
P/K Data Cluster 2 (*1)
disagreement FSW-Cluster 1 BF A8 XX F1 Moderate No
(*1)
FSW-Cluster 2 BF A9 XX F1 Moderate No
(*1)
Duplex SVP Setup fail BF E3 A2 F1 Moderate Yes
SVP CPU FAN Error BF E4 00 F1 Moderate No
SVP HDD FAN Error BF E4 01 F1 Moderate No
SVP PS FAN Error BF E4 02 F1 Moderate No
SVP Temperature Error BF E4 03 F1 Moderate No
HDD Error (SMART) BF E4 04 F1 Moderate No
PS P/L-DKCPNL between Cable BF F2 A0 F1 Moderate No

SIM-RC02-440
Hitachi Proprietary SC01486Z
SIM-RC02-450 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

Error REF code SIM Level of Host Remarks

22 23 13 28 error report
SVP failure Logical inconsistency 70 XX 00 F1 Moderate No
(*2)
HEAP error 71 XX 00 F1 Moderate No
(*2)
File error 72 XX 00 F1 Moderate No
(*2)
LAN error 73 XX 00 F1 Moderate No
(*2)
S-SVP error 74 XX XX F1 Moderate Yes
(*3) (*3)
Windows error 75 XX 00 F1 Moderate No
(*2)
MIX PCB (CHP), 76 00 XY F1 Moderate No
CHA (*5)
CUDG3 detected MX PCB (DKP) 76 01 XY F1 Moderate No
error (*6)
BASE PCB 76 02 00 F1 Moderate No
(Shared Memory)
BASE PCB 76 03 00 F1 Moderate No
(CSW)
BASE PCB 76 04 00 F1 Moderate No
(CACHE)
LCDG3 detected MIX PCB (CHP), 76 10 XY F1 Moderate No
error CHA (*5)
BOOT detected error 79 00 XY F1 Moderate No (*9)
(MIX PCB (CHP), CHA) (*5)
BOOT detected error (MIX PCB (DKP)) 79 01 XY F1 Moderate No (*9)
(*6)
ISDN Router failure 7B 00 03 F1 Moderate Yes
End status of Normal end 7A 00 00 F1 Service No
remote Abnormal end (SVP) 7A 01 00 F1 Service No
microprogram Abnormal end (MP) 7A 02 00 F1 Service No
exchange Version check error 7A 03 XX F1 Service No
(*4)
Sum check error 7A 04 XX F1 Service No
(*4)
LCP patch error 7A 05 XY F1 Service No
(*7)
Warning (Configuration inconsistency) 7A 10 00 F1 Service No
Warning (S-SVP busy) 7A 11 00 F1 Service No
Warning (LCP busy) 7A 12 XY F1 Service No
(*7)
Internet download error 7A 20 00 F1 Service No
Discontinuation by the user 7A 23 00 F1 Service No
Reboot Stop SVP reboot stop (FD Inserted) 7C 00 00 F1 Moderate No
Battery Check Battery life is over 7C 01 00 F1 Moderate No

SIM-RC02-450
Hitachi Proprietary SC01486Z
SIM-RC02-460 DKC515I
Rev.2 / Jul.2005, Apr.2006 Copyright © 2005, 2006, Hitachi, Ltd.

Error REF code SIM Level of Host Remarks

22 23 13 28 error report
Situation Cache Write Pending Ratio Error 7E 00 XX F2 Moderate No XX: CLPR#
Observation Cache Read Hit Ratio Error 7E 01 XX F2 Moderate No XX: CLPR#
Error Cache Side File Use Ratio Error 7E 02 XX F2 Moderate No XX: CLPR#
Async Cache Side File Use Ratio Error 7E 03 XX F2 Moderate No XX: CLPR#
HUR Cache Side File Use Ratio Error 7E 04 XX F2 Moderate No XX: CLPR#
Cache Use Ratio Error 7E 05 XX F2 Moderate No XX: CLPR#
MIX PCB (CHP), 7E 10 XY F1 Moderate No
MP Operating Ratio CHA (*5)
Error MIX PCB (DKP) 7E 11 XY F1 Moderate No
(*6)
Loss Of Signal Count Excess 7E 20 XY F1 Moderate No
(*8)
Bad Received Character Count Excess 7E 21 XY F1 Moderate No
(*8)
Loss Of Synchronization Count Excess 7E 22 XY F1 Moderate No
(*8)
Link Failure Count Excess 7E 23 XY F1 Moderate No
(*8)
Received EOFa Count Excess 7E 24 XY F1 Moderate No
(*8)
Discarded Frame Count Excess 7E 25 XY F1 Moderate No
(*8)
Bad CRC Count Excess 7E 26 XY F1 Moderate No
(*8)
Protocol Error Count Excess 7E 27 XY F1 Moderate No
(*8)
Invalidity Frame Count Excess 7E 28 XY F1 Moderate No
(*8)
SVP failure The term of validity is over 7F F0 00 F1 Serious Yes (*10)
License key
On-demand Cache 7F F0 02 F1 Service No
LUN 7F F0 03 F1 Service No
Pair Failure HRC/HORC/HODM 7F F1 00 F1 Service No
SIM Reduce HRCA/HORCA 7F F1 01 F1 Service No
MRCF/OMRCF 7F F1 02 F1 Service No
HUR 7F F1 03 F1 Service No
COW 7F F1 04 F1 Service No
Dual SVP Standby SVP fail 7F F2 XX F1 Moderate No (*11)
SVP fail over 7F F3 XX F1 Moderate No (*11)
SSVP/MN detection for Duplex SVP 7F F7 00 F1 Moderate No
unsupported
Dump received WCHK1 dump (MIX PCB (CHP), CHA) 30 80 XY F1 Moderate No
(*5)
WCHK1 dump (MIX PCB (DKP)) 31 80 XY F1 Moderate No
(*6)
ABEND dump (MIX PCB (CHP), CHA) 30 81 XY F1 Moderate No
(*5)
ABEND dump (MIX PCB (DKP)) 31 81 XY F1 Moderate No
(*6)
SIM-RC02-460
Hitachi Proprietary SC01486Z
SIM-RC02-470 DKC515I
Rev.1 / May.2005, Jan.2006 Copyright © 2005, 2006, Hitachi, Ltd.

(*1) Error Section (DKU part)

Byte 13 Error Section
60 HDU-RK00
61 HDU-RK01
62 HDU-RK02
63 HDU-RK03
64 HDU-RK10
65 HDU-RK11
66 HDU-RK12
67 HDU-RK13
70 HDU-RK20
71 HDU-RK21
72 HDU-RK22
73 HDU-RK23
74 HDU-RK30
75 HDU-RK31
76 HDU-RK32
77 HDU-RK33

(*2) Contents of byte 23 when a logical error, a HEEP error, a file error, a LAN error or Windows
error occurred
Byte 23 Content
0x00 Dump task
0x01 DKU inline
0x02 Microprogram change (online)
0x03 Information
0x04 LOGOUT
0x05 PATH inline
0x06 Back Ground
0x07 DIAG
0x08 Install
0x09 Online
0x0A Microprogram change (offline)
0x0B Special PCB maintenance
0x0C Common communication function
0xFF Other AP

SIM-RC02-470
Hitachi Proprietary SC01486Z
SIM-RC02-480 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*3) Contents of byte 23 and byte 13 when a S-SVP logical error occurred
Byte23 Byte13 Content
00 01 SSVP ROM SUM Check error (Recovered)
00 02 SSVP RAM RD/WR Error (Recovered)
00 50 Software error (Parameter Error)
10 60 Recovering SVP Communication
10 FF SSVP Failure detected by SVP
50 01 Environment Monitor Register RD/WR error

(*4) Contents of byte 13 when a version check error or sum check error occurred
Byte 13 Micro-program type
00 RAM BOOT
01 DKC MANI
02 LCP
03 MCP
04 LCDG
05 DKU
06 SVP
07 S-SVP
08 CUDG4
09 FCP
10 FOP
20 MAIN DIFF
40 CONFIG
50 HTP
60 FCDG
70 PCDG
80 ROMBOOT

SIM-RC02-480
Hitachi Proprietary SC01486Z
SIM-RC02-490 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*5) Contents of byte 13 when a CHP error occurred.

Content of high byte of Byte 13(X)
High byte of Byte 13 Content
0x4 Basic MIX PCB of cluster 1
0x5 Option CHA of cluster 1
0xC Basic MIX PCB of cluster 2
0xD Option CHA of cluster 2

Content of low byte of Byte 13(Y)

Low byte of Byte 13 Content
0x0 MIX PCB, 1st. CHP of the CHA
0x1 MIX PCB, 2nd. CHP of the CHA
0x2 MIX PCB, 3rd. CHP of the CHA
0x3 MIX PCB, 4th. CHP of the CHA
0x4 5th. CHP of the CHA
0x5 6th. CHP of the CHA
0x6 7th. CHP of the CHA
0x7 8th. CHP of the CHA
In WCHK1 dump and ABEND dump received SIM = 3080XY, 3081XY, the system error code is
indicated on the SIM log detail screen in the format [YYYY] as in Reference Code
3080XY[YYYY].

(*6) Contents of byte 13 when a DKP error occurred.

Content of high byte of Byte 13(X)
High byte of Byte 13 Content
0x0 Basic MIX PCB of cluster 1
0x4 Basic MIX PCB of cluster 2

Content of low byte of Byte 13(Y)

Low byte of Byte 13 Content
0x4 1st. DKP of the MIX PCB
0x5 2nd. DKP of the MIX PCB
0x6 3rd. DKP of the MIX PCB
0x7 4th. DKP of the MIX PCB
In WCHK1 dump and ABEND dump received SIM = 3180XY, 3181XY, the system error code is
indicated on the SIM log detail screen in the format [YYYY] as in Reference Code
3180XY[YYYY].

SIM-RC02-490
Hitachi Proprietary SC01486Z
SIM-RC02-500 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*7) Contents of Byte 13 when a LCP error occurred

Contents of high byte13
High byte of Byte 13 Content
0x4 Basic MIX PCB of cluster 1
0x5 Option CHA of cluster 1
0xC Basic MIX PCB of cluster 2
0xD Option CHA of cluster 2

Contents of low byte 13

Low byte of Byte 13 Content
0x0 MIX PCB, 1st. LCP of the CHA
0x1 MIX PCB, 2nd. LCP of the CHA
0x2 MIX PCB, 3rd. LCP of the CHA
0x3 MIX PCB, 4th. LCP of the CHA
0x4 MIX PCB, 5th. LCP of the CHA
0x5 MIX PCB, 6th. LCP of the CHA
0x6 MIX PCB, 7th. LCP of the CHA
0x7 MIX PCB, 8th. LCP of the CHA
0x8 9th. LCP of the CHA
0x9 10th. LCP of the CHA
0xA 11th. LCP of the CHA
0xB 12th. LCP of the CHA
0xC 13th. LCP of the CHA
0xD 14th. LCP of the CHA
0xE 15th. LCP of the CHA
0xF 16th. LCP of the CHA

SIM-RC02-500
Hitachi Proprietary SC01486Z
SIM-RC02-510 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*8) Content of Byte 13 when a Port error occurred

Contents of high byte 13
High byte of Byte 13 Content
0x4 Basic MIX PCB of cluster 1
0x5 Option CHA of cluster 1
0xC Basic MIX PCB of cluster 2
0xD Option CHA of cluster 2

Contents of low byte 13

Low byte of Byte 13 Content
0x0 MIX PCB, 1st. Port of the CHA
0x1 MIX PCB, 2nd. Port of the CHA
0x2 MIX PCB, 3rd. Port of the CHA
0x3 MIX PCB, 4th. Port of the CHA
0x4 MIX PCB, 5th. Port of the CHA
0x5 MIX PCB, 6th. Port of the CHA
0x6 MIX PCB, 7th. Port of the CHA
0x7 MIX PCB, 8th. Port of the CHA
0x8 9th. Port of the CHA
0x9 10th. Port of the CHA
0xA 11th. Port of the CHA
0xB 12th. Port of the CHA
0xC 13th. Port of the CHA
0xD 14th. Port of the CHA
0xE 15th. Port of the CHA
0xF 16th. Port of the CHA

SIM-RC02-510
Hitachi Proprietary SC01486Z
SIM-RC02-520 DKC515I
Rev.1 / May.2005, Apr.2006 Copyright © 2005, 2006, Hitachi, Ltd.

(*9) Execute the following procedures according to the error code of initialization function which is
shown in 5C-5Fth byte of the SSB with error code 3309. Also, the SSB is the relative log of
SIM with the reference code 7900xx or 7901xx.
Code (4-bytes) Procedures Note
21000041 P/K Replace Replace the package with another new one.
31000041 MP-Install Execute it when the P/S OFF is executed with
Shut Down Jumpers to install the micro-
programs.
P/S OFF Execute them when you have forgotten to pull
Pull out the Shut Down Jumpers out Shut Down Jumpers in the normal P/S
P/S ON ON.
42000041 P/K Replace Replace the package with another new one.
48000041 MP-Install Use the same package in .
In the case that the package is
the same as the type of the
package which you specified in
the define configuration:
(a) MP-Install
(b) P/K Replace (Use the same
package)
In the case that the package is
not same as the type of the
package that you specified in
the define configuration
information:
(a) MP-Install
P/K Replace Replace the package with another new one.
SVP Replace Use the same package in .
MP-Install
P/K Replace
others MP-Install Use the same package in .
P/K Replace
Never fail to make sure the installed micro program version and the each processor’s status by
displaying the status (Status display) after the above procedures is finished.
Then, for the micro program version, “Currently running Microprogram Version” and “Stored
Microprogram Version per Processor” must be confirmed.

Reference address are as follows.

P/K Replace REP01-270
SVP Replace REP01-290 (Work ID : RT7)
MP-Install MICRO-FC05-10
SSB with the error code 3309 SSBLOG05-1250

(*10) Confirm the Program Product Installation status at the ‘License Key’ window of Storage
Navigator.

(*11) REF CODE 13XX

00: Basic SVP
01: Option SVP

SIM-RC02-520
Hitachi Proprietary SC01486Z
SIM-RC03-10 DKC515I
Rev.1 / May.2005, Jul.2005 Copyright © 2005, Hitachi, Ltd.

3. SIM Format
SIM Format (DKC SIM SSB28 = x‘F1’)

0 1 2 3 4 5 6 7
0 x‘00’
1 Permanent ‘0’ ‘1’ x‘0’
Error
2 ‘0’ ‘1’ x‘0’
3
4 x‘000000’
5
6 Serial # Device Track ‘0’ Format (x‘F’)
valid address address
valid valid
7 SIM sense record ID (x‘E0’)
8 Range subject to the error (*1) Range affected by repair (*2)
9 Level of error (*3) Number of Number of Number of Number of Status (*8) 0
faulty SPs SPs in faulty affected
(*4) SSID (*5) SSIDs (*6) SSIDs (*7)
10 Resend (‘0000000’)
SIM (*9)
11 Hardware level (*10)
12 Hardware level (*10)
13 Isolation code (*11)
14 SSB ID SIM sequence number (SIM log record #) SVP ID
(*12) (*13)
15
16
17 DKC serial number
18 (x‘0CA5’+DKC sequence number)
19
20 SSID of self subsystem
21
22 Symptom code (*14)
23
24 Logging and Message Control (*15)
25 Program action code (x‘10’)
26 Dual Frame EDCC ‘00’ Asynchro- Serial Report ‘0’
Mode nous channel output (1)
operation
27 ‘0’ ‘0000’ Extension Fenced
path storage path
configu-
ration
28 x‘F1’
29 Affected SSID
30
31 x‘00’

SIM-RC03-10
Hitachi Proprietary SC01486Z
SIM-RC03-20 DKC515I
Rev.1 / May.2005, Jul.2005 Copyright © 2005, Hitachi, Ltd.

SIM Format (CACHE SIM SSB28 = x‘F2’)

0 1 2 3 4 5 6 7
0 x‘00’
1 Permanent ‘0’ ‘1’ x‘0’
Error
2 ‘0’ ‘1’ x‘0’
3
4 x‘000000’
5
6 Serial # Device Track ‘0’ Format (x‘F’)
valid address address
valid valid
7 SIM sense record ID (x‘E0’)
8 Range subject to the error (*1) Range affected by repair (*2)
9 Level of error (*3) Number of Number of Number of Number of Status (*8) 0
faulty SPs SPs in faulty affected
(*4) SSID (*5) SSIDs (*6) SSIDs (*7)
10 Resend (‘0000000’)
SIM (*9)
11 Hardware level (*10)
12 Hardware level (*10)
13 Isolation code (*11)
14 SSB ID SIM sequence number (SIM log record #) SVP ID
(*12) (*13)
15
16
17 DKC serial number
18 (x‘0CA5’+DKC sequence number)
19
20 SSID of self subsystem
21
22 Symptom code (*14)
23
24 Logging and Message Control (*15)
25 Program action code (x‘10’)
26 Dual Frame EDCC ‘00’ Asynchro- Serial Report ‘0’
Mode nous channel output
operation
27 ‘0’ ‘0000’ Extension Fenced storage path
path
configu-
ration
28 x‘F2’
29 Affected SSID
30
31 x‘00’

SIM-RC03-20
Hitachi Proprietary SC01486Z
SIM-RC03-30 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

SIM Format (DEVICE SIM SSB28 = x‘FE’)

0 1 2 3 4 5 6 7
0 x‘0000’
1
2 Storage Control Type (x‘06’)
3 x‘00’
4 Affected SP Device Address
5 Device Type
6 Serial # Device Track ‘0’ Format (x‘F’)
valid address address
valid valid
7 SSB ID SIM Sequence ID SVP ID
(*12) (*13)
8 Device Exception (x‘1’) Service Message (*16)
9 Level of error (*3) ‘000000’
10 Resend (‘0000000’)
SIM (*9)
11 Exception Class Fru List Code (x‘80’)
12 Hardware and Microcode Corequisite Indicator (x‘01’)
13 Device Address (See reference code)
14 Action Flag (x‘05’)
15
16
17 Drive serial number
18 (x‘0CA5’+DKU sequence number)
19
20 SSID of self subsystem
21
22 Symptom code (*14)
23
24 Logging & Message Control (*15)
25 Program Action Code (x‘10’)
26 Dual Frame EDCC x‘0’ x‘0’ Asynchro- Serial ‘1’ ‘0’
Mode nous Channel
operation
27 x‘0’ x‘0’ Extension Storage path
path
configu-
ration
28 x‘FE’
29
30 x‘000000’
31

SIM-RC03-30
Hitachi Proprietary SC01486Z
SIM-RC03-40 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

SIM Format (MEDIA SIM SSB28 = x‘FF’)

0 1 2 3 4 5 6 7
0 x‘0000’
1
2 Storage Control Type (x‘06’)
3 x‘00’
4 Affected SP Device Address
5 Device Type
6 Serial # Device Track ‘0’ Format (x‘F’)
valid address address
valid valid
7 SSB ID SIM Sequence ID SVP ID
(*12) (*13)
8 Device Exception (x‘1’) Service Message (x‘1’)
9 Level of error (*3) Media Maintenance Procedure Number
(correctable: x‘07’, uncorrectable: x‘05’)
10 Resend (‘0000000’)
SIM (*9)
11 Exception Class Fru List Code (x‘80’)
12 Hardware and Microcode Corequisite Indicator (x‘01’)
13 Device Address (See reference code)
14 Correctable: x‘87’, uncorrectable: x‘85’
15
16
17 Drive serial number
18 (x‘0CA5’+DKU sequence number)
19
20 SSID of self subsystem
21
22 Symptom code (*14)
23
24 Logging & Message Control (*15)
25 Program Action Code (x‘10’)
26 Dual Frame EDCC x‘0’ x‘0’ Asynchro- Serial ‘1’ ‘0’
Mode nous Channel
operation
27 x‘0’ x‘0’ Extension Storage path
path
configu-
ration
28 x‘FF’
29 Cylinder Address High
30 Cylinder Address Low
31 Head Address

SIM-RC03-40
Hitachi Proprietary SC01486Z
SIM-RC03-50 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*1) Range subject to the error

When byte 28 is x‘F1’ (DKC SIM) When byte 28 is x‘F2’ (CACHE SIM)
x‘0’: Not used x‘0’: Not used
x‘1’: Error range not known x‘1’: Error range not known
x‘2’: SP error x‘2’: Error between SP and CACHE
x‘3’: CHL-I error x‘3’: CACHE error
x‘4’: Not affect performance x‘4’: DC/FW error
x‘5’ to x‘F’: Not used x‘5’: FW error
x‘6’ to x‘F’: Not used

(*2) Range affected by repair

When byte 28 is x‘F1’(DKC SIM) When byte 28 is x‘F2’ (CACHE SIM)
x‘0’: Not used x‘0’: Not used
x‘1’: Repair range not known x‘1’: Repair range not known
x‘2’: Repair does not affect performance x‘2’: Repair does not affect performance
x‘3’: SP disabled during repair x‘3’: CACHE error
x‘4’: SSID disabled during repair x‘4’: DC/FW error
x‘5’ to x‘F’: Not used x‘5’: FW error
x‘6’ to x‘F’: Not used

(*3) Level of error

B‘00’: Service SIM
B‘01’: Moderate SIM
B‘10’: Serious SIM
B‘11’: Acute SIM

(*4) Number of faulty SPs

B‘0’: 1 SP
B‘1’: 2 SPs

(*5) Number of SPs in SSID

B‘0’: 2 SPs
B‘1’: 4 SPs

(*6) Number of faulty SSIDs

B‘0’: 1
B‘1’: 2

(*7) Number of affected SSIDs

B‘0’: 1
B‘1’: 2

SIM-RC03-50
Hitachi Proprietary SC01486Z
SIM-RC03-60 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*8) Status
B‘0’: Degeneration
B‘1’: Stop

(*9) Resend SIM

B‘0’: Not resent SIM
B‘1’: Resent SIM

(*10) Hardware level

Bit 0: ESCON hardware level

[When bit 0 is 0] [When bit 0 is 1]

Bit 1: Not used Bit 1: Not used
Bits 2-3: Report storage path Bits 2-3: Error storage path
Bits 4-5: Number of channels per Bits 4-7: Number of channels per
cluster cluster
B‘00’ = 4 0000: Metal = 4, ESCON = 0
B‘01’ = 8 0001: Metal = 8, ESCON = 0
B‘10’ = Not used 0010: Metal = 4, ESCON = 2
B‘11’ = Not used 0100: Metal = 4, ESCON = 4
Bit 6: NVS 0110: Metal = 0, ESCON = 2
B‘0’ = No NVS 1000: Metal = 0, ESCON = 4
B‘1’ = NVS provided 1010: Metal = 0, ESCON = 8
Bit 7: Not used 1100: Metal = 0, ESCON = 6
Bits 8-10: Cache size Bit 8: Dual frame
000: Non cache 0: Dual frame
001: 256MB 1: Modular power
010: 512MB Bits 9-11: Cache size
011: 768MB 000: Non cache
100: 1024MB 001: 256MB
101: 1280MB 010: 512MB
110: 1536MB 011: 768MB
111: Over 1536MB 100: 1024MB
Bits 11-13: Cluster hardware level 101: 1280MB
Bits 14-15: Cache/NVS hardware level 110: 1536MB
111: Over 1536MB
Bits 12-13: Cluster hardware level
Bits 14-15: Cache/NVS hardware level

(*11) Isolation code

Byte 13 ≠ X‘00’ Bytes 22 and 23 are a symptom code.
Byte 13 = X‘00’ Bytes 22 and 23 are an isolation code. This byte is byte 2 of the
association code.

SIM-RC03-60
Hitachi Proprietary SC01486Z
SIM-RC03-70 DKC515I
Rev.0 / May.2005 Copyright © 2005, Hitachi, Ltd.

(*12) SSB ID
B‘0’ = SVP
B‘1’ = SP

(*13) SVP ID
B‘0’ = SVP1
B‘1’ = SVP2

(*14) Symptom code

See bytes 22 and 23 of the reference codes listed in Sections 2.1 and 2.2.

(*15) Logging and Message control

Bit 0 - 3: Not used
Bit 4 - 5: Logging
B‘00’: Do not log
B‘01’: Unconditional log
B‘10’: Log only once
B‘11’: Log only if persistent
Bit 6 - 7: Operator message
B‘00’: No message
B‘01’: Unconditional message
B‘10’: Send only once
B‘11’: Send only if persistent

(*16) Service Message

x‘1’: Action
x‘C’: No action

SIM-RC03-70