0% found this document useful (0 votes)

48 views

3 Phaseckt

1) Three-phase systems are used universally for power generation, transmission and distribution due to their constant power delivery to loads and efficient power transmission. 2) Generators are typically Y-connected to avoid circulating currents, while loads can be either Y- or Δ-connected. 3) For Y-connected loads, line voltages are √3 times the phase voltages and lead the phase voltages by 30°. Phase currents are equal to line currents.

Uploaded by

Engr El-j Tsumo

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

48 views

3 Phaseckt

Uploaded by

Engr El-j Tsumo

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 13

Go to Power SyAnalysis Home Page - PSA Publishing

CHAPTER

2
THREE-PHASE SYSTEMS

2.1 BALANCED THREE-PHASE CIRCUITS

The generation, transmission and distribution of electric power is accomplished by
means of three-phase circuits. At the generating station, three sinusoidal voltages
. This is
are generated having the same amplitude but displaced in phase by
called a balanced source. If the generated voltages reach their peak values in the
sequential order ABC, the generator is said to have a positive phase sequence,
shown in Figure 2.11(a). If the phase order is ACB, the generator is said to have a
negative phase sequence, as shown in Figure 2.11(b).
In a three-phase system, the instantaneous power delivered to the external
loads is constant rather than pulsating as it is in a single-phase circuit. Also, threephase motors, having constant torque, start and run much better than single-phase
motors. This feature of three-phase power, coupled with the inherent efficiency of
its transmission compared to single-phase (less wire for the same delivered power),
accounts for its universal use.
A power system has Y-connected generators and usually includes both and Y-connected loads. Generators are rarely -connected, because if the voltages
are not perfectly balanced, there will be a net voltage, and consequently a circulating current, around the . Also, the phase voltages are lower in the Y-connected

120

2.2. Y-CONNECTED LOADS

ECn

EBn

EAn

ECn

(a)

EAn

(b)

FIGURE 2.1
(a) Positive, or ABC, phase sequence. (b) Negative, or ACB, phase sequence.

generator, and thus less insulation is required. Figure 2.2 shows a Y-connected generator supplying balanced Y-connected loads through a three-phase line. Assuming
a positive phase sequence (phase order ABC) the generated voltages are:

= jEpj6 0
= jEpj6 120
ECn = jEp j6 240

EAn
EBn

(2.1)

In power systems, great care is taken to ensure that the loads of transmission lines
are balanced. For balanced loads, the terminal voltages of the generator VAn , VBn
and VCn and the phase voltages Van , Vbn and Vcn at the load terminals are balanced.
For phase A, these are given by
VAn
Van

= EAn
= VAn

ZG Ia
ZL Ia

(2.2)
(2.3)

2.2 Y-CONNECTED LOADS

To find the relationship between the line voltages (line-to-line voltages) and the
phase voltages (line-to-neutral voltages), we assume a positive, or ABC, sequence.
We arbitrarily choose the line-to-neutral voltage of the a-phase as the reference,
thus

= jVpj6 0
= jVpj6 120
Vcn = jVp j6 240

Van
Vbn

(2.4)

20 2. Three-phase Systems

VAn

Van

EAn

.
.
.
.
.
.
.
.
.
.
....
.
.
.
...
.
.
..
.
.
.
.
.........
......
.
...................
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.. ...
...
. ........................
...... ..............
.
.
.
..
.
......
.
.
.
..
..
.
..
.....
......
.
.
.
..
.
.
.
.
.
..
.
......
.
..
......
.
..
......
....
.
.
......
.
.
.
.
.
.
.
.
.
.
......
......
..
.....
.
....
....
....
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
......
.
.
.
.
.
.
.
.
.
......
......
..
.
....
....
.....
.
..............
.
.
.
.
.
.
.
.
.
.
.....
.
.
.
.
.
.
.
.
.
.
.
..
.
.
..........
...
......
..
.....
.
.
..
......... .
.
.
.
.
.
.
.
.
.
.
.
.
...... .........
.
.......
..
.
.
..
..................
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.....
..
... ..........
.
..
.
.....................................
.....
........................ ...... ...... ...... ........
.
.
.
.....
......
.
..
.
.
.
.
.
.
.
.
.
.
.
.............
..............
..... ..... ..... ..... ..
.
.
..
.
.
.
.
.
.
.
..
.
.
.
.
.
.
..
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
..
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
...........................................................................................................................................................................................................................................................................................................................................
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
... ..... ..... .....
..................................
.
.
.
.
.
.
.
.
.
.................................................................................................................................................................................................................................. ..... .... ...................... . . . .................................................................................................................................................................................................................................
.
. . . .

ECn

VCn

EBn

VBn

Vbn

Vcn

FIGURE 2.2
A Y-connected generator supplying a Y-connected load.

where jVp j represents the magnitude of the phase voltage (line-to-neutral voltage).
The line voltages at the load terminals in terms of the phase voltages are found
by the application of Kirchhoffs voltage law
Vab
Vbc
Vca

= Van
= Vbn
= Vcn

Vbn
Vcn
Van

= jVpj(16 0 16 120 ) = p3jVppj6 30

= jVpj(16 120 16 240 )p= 3jVpj6 90
= jVpj(16 240 16 0 ) = 3jVpj6 150

(2.5)

The voltage phasor diagram of the Y-connected loads of Figure 2.2 is shown in
Figure 2.3. The relationship between the line voltages and phase voltages is demonstrated graphically.
If the rms value of any of the line voltages is denoted by VL , then one of the
important characteristics of the Y-connected three-phase load may be expressed as
VL

= 3 jVpj6 30

(2.6)

Thus in the case of Y-connected loads, the magnitude of the line voltage is

3 times the magnitude of the phase voltage, and for a positive

phase sequence,

the set of line voltages leads the set of phase voltages by 30 .

The three-phase currents in Figure 2.2 also possess three-phase symmetry and
are given by
Ia

= VZanp = jIpj6

2.3.

Vca

-CONNECTED LOADS

Vab

Vcn

Van

Vbn

Vbc

FIGURE 2.3
Phasor diagram showing phase and line voltages.

Ib
Ic

= VZbnp = jIpj6 120

= VZcn = jIpj6 240
p

(2.7)

where is the impedance phase angle.

The currents in lines are also the phase currents (the current carried by the
phase impedances). Thus
IL Ip
(2.8)

2.3

-CONNECTED LOADS

A balanced -connected load (with equal phase impedances) is shown in Figure 2.4.
It is clear from the inspection of the circuit that the line voltages are the same
as phase voltages.
VL Vp
(2.9)

Consider the phasor diagram shown in Figure 2.5, where the phase current Iab is
arbitrarily chosen as reference. we have

= jIpj6 0
= jIpj6 120
Ica = jIp j6 240
Iab
Ibc

where jIp j represents the magnitude of the phase current.

(2.10)

22 2. Three-phase Systems

b
b
b

Iab

Zp Ica

Ibc

FIGURE 2.4
A -connected load.

Ica

Iab

Ibc

FIGURE 2.5
Phasor diagram showing phase and line currents.

The relationship between phase and line currents can be obtained by applying
Kirchhoffs current law at the corners of .
Ia
Ib
Ic

= Iab
= Ibc
= Ica

Ica
Iab
Ibc

= jIpj(16 0 16 240 ) = pp3jIpj6 30

= jIpj(16 120 16 0 ) = 3jIppj6 150
= jIpj(16 240 16 120 ) = 3jIpj6 90

(2.11)

The relationship between the line currents and phase currents is demonstrated
graphically in Figure 2.5.
If the rms of any of the line currents is denoted by IL , then one of the important characteristics of the -connected three-phase load may be expressed as

= 3jIpj 6 30

(2.12)

Thus in the case of -connected loads, the magnitude of the line current is
times the magnitude of the phase current, and with positive phase sequence, the set
of line currents lags the set of phase currents by .

2.4.

-Y TRANSFORMATION

2.4

For analyzing network problems, it is convenient to replace the -connected circuit with an equivalent Y-connected circuit. Consider the fictitious Y-connected
circuit of ZY /phase which is equivalent to a balanced -connected circuit of
Z /phase, as shown in Figure 2.6.

(a)

b b
b

(b)

FIGURE 2.6
(a) to (b) Y-connection.

For the

-connected circuit, the phase current Ia is given by

Vab
Vac
Vab + Vac
Ia =
+
=
Z
Z
Z

(2.13)

Vab

Vcn

Van

Vac

Vbn

FIGURE 2.7
Phasor diagram showing phase and line voltages.

The phasor diagram in Figure 2.7 shows the relationship between balanced phase
and line-to-line voltages. From this phasor diagram, we find
Vab

+ Vac = 3 jVan j6 30 + 3 jVan j6 30

= 3Van

(2.14)
(2.15)

24 2. Three-phase Systems

Substituting in (2.13), we get

= 3ZVan

or
Van

= Z3 Ia

(2.16)

Now, for the Y-connected circuit, we have

Van

= ZY Ia

(2.17)

Thus, from (2.16) and (2.17), we find that

= Z3

(2.18)

2.5 PER-PHASE ANALYSIS

The current in the neutral of the balanced Y-connected loads shown in Figure 2.2
is given by
In Ia Ib Ic
(2.19)

= + + =0

Since the neutral carries no current, a neutral wire of any impedance may be replaced by any other impedance, including a short circuit and an open circuit. The
return line may not actually exist, but regardless, a line of zero impedance is included between the two neutral points. The balanced power system problems are
then solved on a per-phase basis. It is understood that the other two phases carry
identical currents except for the phase shift.
We may then look at only one phase, say phase A, consisting of the source
VAn in series with ZL and Zp , as shown in Figure 2.8. The neutral is taken as datum
and usually a single-subscript notation is used for phase voltages.
If the load in a three-phase circuit is connected in a , it can be transformed
into a Y by using the -to-Y transformation. When the load is balanced, the
impedance of each leg of the Y is one-third the impedance of each leg of the , as
given by (2.18), and the circuit is modeled by the single-phase equivalent circuit.

2.6 BALANCED THREE-PHASE POWER

Consider a balanced three-phase source supplying a balanced Y- or
load with the following instantaneous voltages
van

= 2jVpj cos(!t + v )

- connected

2.6. BALANCED THREE-PHASE POWER

FIGURE 2.8
Single-phase circuit for per-phase analysis.

= p2jVpj cos(!t + v 120 )

vcn = 2jVp j cos(!t + v 240 )
vbn

(2.20)

For a balanced load the phase currents are

= p2jIpj cos(!t + i)

ib = 2jIp j cos(!t + i 120 )
p
ic = 2jIp j cos(!t + i 240 )

(2.21)

where jVp j and jIP j are the magnitudes of the rms phase voltage and current, respectively. The total instantaneous power is the sum of the instantaneous power of
each phase, given by
p3 van ia vbn ib vcn ic
(2.22)

Substituting for the instantaneous voltages and currents from (2.20) and (2.21) into
(2.22)
p3

= 2jVpjjIp j cos(!t + v )cos(!t + i)

+2jVpjjIpj cos(!t + v 120 )cos(!t + i 120 )
+2jVpjjIpj cos(!t + v 240 )cos(!t + i 240 )

Using the trigonometric identity (??)

= jVpjjIpj[cos(v i) + cos(2!t + v + i)]

+jVpjjIpj[cos(v i) + cos(2!t + v + i 240 )]
+jVpjjIpj[cos(v i) + cos(2!t + v + i 480 )]

(2.23)

The three double frequency cosine terms in (2.23) are out of phase with each other
and add up to zero, and the three-phase instantaneous power is
by

120

= 3jVpjjIpj cos

(2.24)

26 2. Three-phase Systems

v i is the angle between phase voltage and phase current or the impedance
angle.
Note that although the power in each phase is pulsating, the total instantaneous power is constant and equal to three times the real power in each phase. Indeed, this constant power is the main advantage of the three-phase system over the
single-phase system. Since the power in each phase is pulsating, the power, then,
is made up of the real power and the reactive power. In order to obtain formula
symmetry between real and reactive powers, the concept of complex or apparent
power (S ) is extended to three-phase systems by defining the three-phase reactive
power as
Q3
jVpjjIpj
(2.25)

sin

Thus, the complex three-phase power is

= P3 + jQ3

(2.26)

= 3VpIp

(2.27)

Equations (2.24) and (2.25) are sometimes expressed in terms of the rms
magnitude of the line voltage and the rms magnitude
of the line current. In a Yp
connected load the phase voltage jVp j jVL j=p and the phase current Ip IL .
In the -connection Vp VL and jIp j jIL j= . Substituting for the phase voltage and phase currents in (2.24) and (2.25), the real and reactive powers for either
connection are given by
p
P3
jVLjjIL j
(2.28)

=
=

= 3

and

3
3

cos

= 3jVLjjIL j sin

(2.29)

A comparison of the last two expressions with (2.24) and (2.25) shows that the
equation for the power in a three-phase system is the same for either a Y or a
connection when the power is expressed in terms of line quantities.
When using (2.28) and (2.29) to calculate the total real and reactive power,
remember that is the phase angle between the phase voltage and the phase current.
As in the case of single-phase systems for the computation of power, it is best to
use the complex power expression in terms of phase quantities given by (2.27).
The rated power is customarily given for the three-phase and rated voltage is the
line-to-line voltage. Thus, in using the per-phase equivalent circuit,
p care must be
.
taken to use per-phase voltage by dividing the rated voltage by

Example 2.7
A three-phase line has an impedance of

2 + j 4
as shown in Figure 2.9.

2.6. BALANCED THREE-PHASE POWER

aj j = 2072 +85 4
a
a
a
a
a
30

. . . .
.... .... .... ....
................................................................................................. ... ... ... .....................................................................................................................................................................................
.
.
... .
.
.
.
... ............. .
.
.
.
.
.. ..
.
.
.
.
.
.
....... ..
.
.
.
.
.
...... ..
.....
.
..
.
.........
.
.
.
.
.
.
.
.
.
.
.
.
.
.....
........ ..
.
.
.
.
.
.
.
.
.
.
.
.
........
.
.....
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
........
..
..
................................................................................................. ..... ..... ..... ........................................................................................
.............
.
.
.
...... .
.
.
.
...
.
........ .
.
.
.
.
.
.. ..
.
.
.
....
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
....
.
.
.
. ........... .
..
.
.
.
...... .
..
........
.
.
........
.
..
.
.
........
.
.
. ..
.
.
.
......
....
.
.
.
.
.
.
.
.
.
.
. ....... .
.
.
..
.
.
. . . .
.
.
... ... ... ...
...........................................................................................
.
................................................................................................. ..... ..... ..... ..........................................................................................
........
.
.
.
.
.
...
.
.
...
.
.
..
.
...........
.
..
.
.
..
.......
.
.
.
.
.
.
...
.
.
...
.
.........
.
...
.
.
.
.
.
.
..
....
.
.
..
.
.
.
.
.......
.
....
.
.
...
.
....
.
.
.
.
.
.
.
..
.
....
.
.
.
.
.
.
.
.
.
.
...
.
.
.
.
..
.
.................
.
.
..
.
.
.
.
.
.........
.
........ .
...
.
.
.
.
.
.
.
...... ..
.
...
.
.
....
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
... ...
......
.
..
.. .
.
.
.
.
.
.
.
.
.
.
.
.
.
.. ......
.
.
..
.
.
. .
.
......
........ .... .
.
.
.
.
.
.
. .....
..

j 45

FIGURE 2.9
Three-phase circuit diagram for Example 2.7.

The line feeds two balanced three-phase loads that are connected in parallel. The
j
per phase. The second
first load is Y-connected and has an impedance of
j
. The line is energized
load is -connected and has an impedance of
: V.
at the sending end from a three-phase balanced supply of line voltage
Taking the phase voltage Va as reference, determine:
(a) The current, real power, and reactive power drawn from the supply.
(b) The line voltage at the combined loads.
(c) The current per phase in each load.
(d) The total real and reactive powers in each load and the line.

30+ 40

60 45

207 85

(a) The -connected load is transformed into an equivalent Y. The impedance per
phase of the equivalent Y is
Z2

= 60 3 j 45 = 20

The phase voltage is

= 207p:385 = 120 V

The single-phase equivalent circuit is shown in Figure 2.10.

The total impedance is
Z

j 40)(20 j 15)
= 2 + j 4 + (30(30++j 40)
+ (20 j 15)
= 2 + j 4 + 22 j 4 = 24

With the phase voltage Van as reference, the current in phase a is

= VZ1 = 12024 0 = 5 A
6

28 2. Three-phase Systems

V1
n

2 + j 4

= 1206 0 V

j 40

j 15

FIGURE 2.10
Single-phase equivalent circuit for Example 2.7.

The three-phase power supplied is

= 3V1 I = 3(1206 0 )(56 0) = 1800 W

(b) The phase voltage at the load terminal is

= 1206 0 (2 + j 4)(56 0 ) = 110 j 20

= 111:86 10:3 V

The line voltage at the load terminal is

V2ab

= 3 6 30 V2 = 3 (111:8)6 19:7 = 193:646 19:7 V

(c) The current per phase in the Y-connected load and in the equivalent Y of the
load is
j 20
= ZV2 = 110
= 1 j 2 = 2:2366 63:4 A
1 30 + j 40
V2
110 j 20 = 4 + j 2 = 4:4726 26:56 A
I2 =
=
Z2
20 j 15
The phase current in the original -connected load, i.e., Iab is given by
I2
4:p4726 26:56 = 2:5826 56:56 A
Iab = p
=
36 30
36 30
I1

(d) The three-phase power absorbed by each load is

= 3V2 I1 = 3(111:86

S2 = 3V2 I2 = 3(111:86
S1

10:3 )(2:2366 63:4 ) = 450 W + j 600 var

10:3 )(4:4726 26:56 ) = 1200 W j 900 var

The three-phase power absorbed by the line is

= 3(RL + jXL )jI j2 = 3(2 + j 4)(5)2 = 150 W + j 300 var

2.6. BALANCED THREE-PHASE POWER

It is clear that the sum of load powers and line losses is equal to the power delivered
from the supply, i.e.,
S1

+ S2 + SL = (450 + j 600) + (1200

= 1800 W + j 0 var

Example 2.8

900) + (150 + j 300)

0 4+ 2 7

A three-phase line has an impedance of :

j :
per phase. The line feeds two
balanced three-phase loads that are connected in parallel. The first load is absorb: kVA at :
power factor lagging. The second load absorbs
kW at
ing
unity power factor. The line-to-line voltage at the load end of the line is
: V.
Determine:

560 1

0 707

132
3810 5

(a) The magnitude of the line voltage at the source end of the line.
(b) Total real and reactive power loss in the line.
(c) Real power and reactive power supplied at the sending end of the line.
(a) The phase voltage at the load terminals is
V2

p :5 = 2200 V
= 3810
3

The single-phase equivalent circuit is shown in Figure 2.11.

0:4 + j 2:7

V1
n

= 22006 0

FIGURE 2.11
Single-phase equivalent diagram for Example 2.8.

The total complex power is

SR(3)

= 560:1(0:707 + j 0:707) + 132 = 528 + j 396

= 6606 36:87 kVA

With the phase voltage V2 as reference, the current in the line is

S
; 0006
36:87 = 1006 36:87 A
= 3RV(3) = 6603(2200
6 0 )
2

30 2. Three-phase Systems

The phase voltage at the sending end is

= 22006 0 + (0:4 + j 2:7)1006 36:87 = 2401:76 4:58 V

The magnitude of the line voltage at the sending end of the line is

p
p
jV1 Lj = 3jV1 j = 3(2401:7) = 4160 V

(b) The three-phase power loss in the line is

SL(3)

= 3RjI j2 + j 3X jI j2 = 3(0:4)(100)2 + j 3(2:7)(100)2

= 12 kW + j 81 kvar

(c) The three-phase sending power is

SS (3)

= 3V1I = 3(2401:76 4:58 )(1006 36:87 ) = 540 kW + j 477 kvar

It is clear that the sum of load powers and the line losses is equal to the power
delivered from the supply, i.e.,
SS (3)

= SR(3) + SL(3) = (528 + j 396) + (12 + j 81) = 540 kW + j 477 kvar

Ell100: Introduction To Electrical Engg.: 3 Phase AC Power Circuits
No ratings yet
Ell100: Introduction To Electrical Engg.: 3 Phase AC Power Circuits
38 pages
ESO 210 Introduction To Electrical Engineering: Lecture-12 Three Phase AC Circuits
No ratings yet
ESO 210 Introduction To Electrical Engineering: Lecture-12 Three Phase AC Circuits
45 pages
CH12
No ratings yet
CH12
27 pages
Three Phase System
No ratings yet
Three Phase System
41 pages
Ch-5 Introduction To Poly Phase System
No ratings yet
Ch-5 Introduction To Poly Phase System
27 pages
Three Phase 14.05.23
No ratings yet
Three Phase 14.05.23
22 pages
Three Phase System
No ratings yet
Three Phase System
53 pages
Three Phase Systems_v1
No ratings yet
Three Phase Systems_v1
40 pages
3-Phase Volt
No ratings yet
3-Phase Volt
14 pages
Chapter 1: Three-Phase Circuits: Objectives
No ratings yet
Chapter 1: Three-Phase Circuits: Objectives
13 pages
Lecture 2: Three-Phase System
No ratings yet
Lecture 2: Three-Phase System
30 pages
Electrical Circuit II Prof Masud RUET 2021
No ratings yet
Electrical Circuit II Prof Masud RUET 2021
63 pages
Lecture 8
No ratings yet
Lecture 8
36 pages
ESO 210 Introduction To Electrical Engineering: Lecture-13 Three Phase AC Circuits
No ratings yet
ESO 210 Introduction To Electrical Engineering: Lecture-13 Three Phase AC Circuits
34 pages
PE351 Lect4 2020
No ratings yet
PE351 Lect4 2020
31 pages
Three Phase System
No ratings yet
Three Phase System
20 pages
L4
No ratings yet
L4
66 pages
Chapter 7
No ratings yet
Chapter 7
16 pages
Multiphase A.C. Emfs (Produced by Multiple Windings)
No ratings yet
Multiphase A.C. Emfs (Produced by Multiple Windings)
6 pages
Multiphase A.C. Emfs (Produced by Multiple Windings)
No ratings yet
Multiphase A.C. Emfs (Produced by Multiple Windings)
6 pages
Multiphase A.C. Emfs (Produced by Multiple Windings)
No ratings yet
Multiphase A.C. Emfs (Produced by Multiple Windings)
6 pages
Fee 8
No ratings yet
Fee 8
31 pages
Three Phase Circuits
No ratings yet
Three Phase Circuits
17 pages
Three Phase Networks
No ratings yet
Three Phase Networks
12 pages
3_phase_Balanced_circuit
No ratings yet
3_phase_Balanced_circuit
67 pages
CH 12
No ratings yet
CH 12
22 pages
Network Theory by Sreekanth
No ratings yet
Network Theory by Sreekanth
15 pages
Introduction To Three-Phase Systems
No ratings yet
Introduction To Three-Phase Systems
17 pages
Electrical Machines - AC - Circuits
No ratings yet
Electrical Machines - AC - Circuits
15 pages
3 Phase Notes
No ratings yet
3 Phase Notes
13 pages
Three Phase System
No ratings yet
Three Phase System
34 pages
Three-Phase Systems: M. I - Elsaid
No ratings yet
Three-Phase Systems: M. I - Elsaid
25 pages
Chapter 1
No ratings yet
Chapter 1
64 pages
Ch-12-Three Phase
No ratings yet
Ch-12-Three Phase
16 pages
Eee 18
No ratings yet
Eee 18
34 pages
EE353 Electric Power System: Three Phase Circuits
No ratings yet
EE353 Electric Power System: Three Phase Circuits
25 pages
c3 PDF
No ratings yet
c3 PDF
25 pages
LMH - Chapter4-Three Phase Circuit
No ratings yet
LMH - Chapter4-Three Phase Circuit
83 pages
Pages From Cir2 - Lect - 8 - Introduction - To - Poly - Phase PDF
No ratings yet
Pages From Cir2 - Lect - 8 - Introduction - To - Poly - Phase PDF
33 pages
Circuit Theory (Eceg-1081) : Addis Ababa University Addis Ababa Institute of Technology (Aait)
No ratings yet
Circuit Theory (Eceg-1081) : Addis Ababa University Addis Ababa Institute of Technology (Aait)
19 pages
Unit 3 - 3 Phase Circuits Basics
No ratings yet
Unit 3 - 3 Phase Circuits Basics
18 pages
Poly-Phase Circuits
No ratings yet
Poly-Phase Circuits
19 pages
Three-Phase Power Circuits: Lecture Notes: EEE Instructor: Dr. U D Dwivedi
No ratings yet
Three-Phase Power Circuits: Lecture Notes: EEE Instructor: Dr. U D Dwivedi
39 pages
ESO 210 Lecture-14 - 2014
No ratings yet
ESO 210 Lecture-14 - 2014
39 pages
Basic Elec Chapter 5
No ratings yet
Basic Elec Chapter 5
19 pages
Signals and Systems Chapter 12
No ratings yet
Signals and Systems Chapter 12
34 pages
Three Phase Circuits
No ratings yet
Three Phase Circuits
15 pages
Beee MC & TC
No ratings yet
Beee MC & TC
47 pages
Chapter Four Part1
No ratings yet
Chapter Four Part1
12 pages
12B Three-Phase Circuit
No ratings yet
12B Three-Phase Circuit
28 pages
Ch4 - Three-Phase Circuits Magnetically Coupled Circuits
No ratings yet
Ch4 - Three-Phase Circuits Magnetically Coupled Circuits
39 pages
ELL 100 Introduction To Electrical Engineering:: T - P ACC
No ratings yet
ELL 100 Introduction To Electrical Engineering:: T - P ACC
87 pages
CH 6
No ratings yet
CH 6
31 pages
Electrical Engineering: Three-Phase System
No ratings yet
Electrical Engineering: Three-Phase System
50 pages
E04-038 - Three-Phase Power Systems - US
No ratings yet
E04-038 - Three-Phase Power Systems - US
28 pages
Three Phase Circuits: Unit-V
100% (2)
Three Phase Circuits: Unit-V
43 pages
CamScanner 05-09-2021 14.26
No ratings yet
CamScanner 05-09-2021 14.26
28 pages
Three Phase Circuits
No ratings yet
Three Phase Circuits
82 pages
Electrostatic Kinetic Energy Harvesting
From Everand
Electrostatic Kinetic Energy Harvesting
Philippe Basset
No ratings yet
Exercises of Optics and Electromagnetism
From Everand
Exercises of Optics and Electromagnetism
Simone Malacrida
No ratings yet