MELDAS Series

M700 Alarm Parameter Manual

USA-E99090 -006*

MITSUBISHI ELECTRIC AUTOMATION USA

List of Revisions
Rev * Date of Revision 10/27/04 Detail First Edition Created Author TSS

MELDAS Series

M700 Alarm Parameter Manual (IB1500038-E)

USA-E99080 -061*

MITSUBISHI ELECTRIC AUTOMATION USA

List of Revisions
Rev * Date of Revision 10/01/04 Detail First Edition Created Author TSS

MELDAS Series

M700 Series Alarm Parameter Manual

USA-E01091 -004*

MITSUBISHI ELECTRIC AUTOMATION USA

List of Revisions
Rev * Date of Revision 06/16/04 Detail First Edition Created Author TSS

MITSUBISHI CNC 700 Series ALARM/PARAMETER MANUAL

IB(NA)1500038(ENG)

MITSUBISHI CNC is a registered trademark of Mitsubishi Electric Corporation. Other company and product names that appear in this manual are trademarks or registered trademarks of the respective company.

PREFACE
This manual is the alarm/parameter guide required to use the MITSUBISHI 700 Series. This manual is prepared on the assumption that your machine is provided with all of the 700 Series functions. Confirm the functions available for your NC before proceeding to operation by referring to the specification issued by the machine manufacturer.

Notes on Reading This Manual (1) This manual explains general parameters as viewed from the NC. For information about each machine tool, refer to manuals issued from the machine manufacturer. If the descriptions relating to restrictions and allowable conditions conflict between this manual and the machine manufacturer's instruction manual, the later has priority over the former. (2) This manual is intended to contain as much descriptions as possible even about special operations. The operations to which no reference is made in this manual should be considered impossible. (3) The special display unit explained in this manual is the display unit incorporated by the machine manufacturer, and is not the MITSUBISHI standard display unit.

Caution
If the descriptions relating to the restrictions and allowable conditions conflict between this manual and the machine manufacturers instruction manual the latter has priority over the former. The operations to which no reference is made in this manual should be considered impossible. This manual is complied on the assumption that your machine is provided with all optional functions. Confirm the functions available for your machine before proceeding to operation by referring to the specification issued by the machine manufacturer. In some NC system versions there may be cases that different pictures appear on the screen the machine operates in a different way or some function is not activated.

Precautions for Safety

Always read the specifications issued by the machine maker, this manual, related manuals and attached documents before installation, operation, programming, maintenance or inspection to ensure correct use. Understand this numerical controller, safety items and cautions before using the unit. This manual ranks the safety precautions into "DANGER", "WARNING" and "CAUTION".

DANGER WARNING CAUTION

When the user may be subject to imminent fatalities or major injuries if handling is mistaken. When the user may be subject to fatalities or major injuries if handling is mistaken.

When the user may be subject to injuries or when physical damage may occur if handling is mistaken. CAUTION", may lead to major results depending on the situation. In any case,

Note that even items ranked as "

important information that must always be observed is described.

DANGER
Not applicable in this manual.

WARNING
Not applicable in this manual.

CAUTION
1. Items related to product and manual If the descriptions relating to the restrictions and allowable conditions conflict between this manual and the machine manufacturers instruction manual the latter has priority over the former. The operations to which no reference is made in this manual should be considered impossible. This manual is complied on the assumption that your machine is provided with all optional functions. Confirm the functions available for your machine before proceeding to operation by referring to the specification issued by the machine manufacturer. In some NC system versions there may be cases that different pictures appear on the screen the machine operates in a different way on some function is not activated. 2. Items related to faults and abnormalities If the BATTERY LOW alarm is output, save the machining programs, tool data and parameters to an input/output device, and then replace the battery. If the BATTERY alarm occurs, the machining programs, tool data and parameters may be damaged. After replacing the battery, reload each data item. [Continued on next page]

CAUTION
3. Items related to maintenance Do not replace the battery while the power is ON. Do not short-circuit, charge, heat, incinerate or disassemble the battery. Dispose of the spent battery according to local laws. 4. Items related to servo parameters and spindle parameters

[Continued]

With the MDS-C1 Series, only the serial encoder is compatible as the motor end detector. The OHE/OHA type detector cannot be used as the motor end detector. Do not adjust or change the parameter settings greatly as operation could become unstable. In the explanation on bits, set all bits not used, including blank bits, to 0.

CONTENS I
1.

EXPLANATION OF ALARMS
LIST OF ALARMS................................................................................................................................ 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 OPERATION ALARMS............................................................................................................... 1 STOP CODES ............................................................................................................................ 9 SERVO ALARMS ..................................................................................................................... 14 SPINDLE ALARMS .................................................................................................................. 24 MCP ALARM ........................................................................................................................... 29 SYSTEM ALARMS .................................................................................................................. 32 ABSOLUTE POSITION DETECTION SYSTEM ALARMS ...................................................... 36 MESSAGES DURING EMERGENCY STOP .......................................................................... 39 AUXILIARY AXIS ALARMS ...................................................................................................... 41

1.10 COMPUTER LINK ERRORS.................................................................................................... 48 1.11 USER PLC ALARMS ................................................................................................................ 49 2. OPERATION MESSAGES ON SETTING AND DISPLAY UNIT ....................................................... 50 2.1 2.2 OPERATION ERRORS ............................................................................................................ 50 OPERATOR MESSAGES ........................................................................................................ 60 2.2.1 SEARCH AND OPERATION RELATED .................................................................... 60 2.2.2 MDI/EDITING RELATED ............................................................................................ 61 2.2.3 DATA INPUT/OUTPUT RELATED ............................................................................. 62 2.2.4 S-ANALOG OUTPUT ADJUSTMENT RELATED ...................................................... 63 2.2.5 AUXILIARY AXIS ......................................................................................................... 63 2.2.6 PARAMETER BACKUP RELATED ............................................................................. 63 2.2.7 OTHERS ...................................................................................................................... 64

3.

PROGRAM ERROR ........................................................................................................................... 65

-i-

II
1.

EXPLANATION OF PARAMETERS
SCREEN CONFIGURATION ............................................................................................................... 1 1.1 SCREEN TRANSITION CHARTS .............................................................................................. 1

2.

MACHINING PARAMETERS ............................................................................................................... 3 2.1 2.2 2.3 2.4 2.5 PROCESS PARAMETERS ........................................................................................................ 3 CONTROL PARAMETERS ...................................................................................................... 10 AXIS PARAMETERS................................................................................................................ 12 BARRIER DATA ....................................................................................................................... 14 TOOL MEASUREMENT PARAMETERS ................................................................................. 16

3.

I/O PARAMETERS ............................................................................................................................. 17 3.1 3.2 3.3 BASE PARAMETERS .............................................................................................................. 17 I/O DEVICE PARAMETERS..................................................................................................... 18 COMPUTER LINK PARAMETERS .......................................................................................... 20

4. 5. 6.

SETUP PARAMETERS...................................................................................................................... 22 BASE SPECIFICATIONS PARAMETERS ........................................................................................ 23 AXIS SPECIFICATIONS PARAMETERS .......................................................................................... 92 6.1 6.2 6.3 6.4 AXIS SPECIFICATIONS PARAMETERS................................................................................. 92 ZERO POINT RETURN PARAMETERS.................................................................................. 99 ABSOLUTE POSITION PARAMETERS ................................................................................ 102 AXIS SPECIFICATIONS PARAMETERS 2............................................................................ 104

7.

SERVO PARAMETERS ................................................................................................................... 112 7.1 7.2 7.3 MDS-B-SVJ2 .......................................................................................................................... 114 MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE).......................................................... 140 MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE) .............................. 168

- ii -

7.4

SUPPLEMENT ....................................................................................................................... 198 7.4.1 D/A OUTPUT SPECIFICATIONS .............................................................................. 198 7.4.2 ELECTRONIC GEARS .............................................................................................. 204 7.4.3 LOST MOTION COMPENSATION............................................................................ 206

8.

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS ........................................................................... 207 8.1 8.2 8.3 MDS-B-SP/SPH,SPJ2 SPINDLE BASE SPECIFICATIONS PARAMETERS........................ 207 MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS.................................................................. 215 MDS-B-SP/SPH,SPJ2 SUPPLEMENTARY EXPLANATION (FOR D/A OUTPUT FUNCTIONS)......................................................................................... 252

9.

MDS-C1-SP, SPM SPINDLE PARAMETERS ................................................................................. 255 9.1 9.2 9.3 9.4 9.5 MDS-C1-SP SPINDLE BASE SPECIFICATIONS PARAMETERS........................................ 255 MDS-C1-SP SPINDLE PARAMETERS.................................................................................. 262 MDS-C1-SPM SPINDLE PARAMETERS............................................................................... 292 MDS-C1-SP SUPPLEMENTARY EXPLANATION................................................................. 321 MDS-C1-SPM SUPPLEMENTARY EXPLANATION.............................................................. 325

10. MACHINE ERROR COMPENSATION............................................................................................. 329 10.1 FUNCTION OUTLINE............................................................................................................. 329 10.2 SETTING COMPENSATION DATA ....................................................................................... 333 10.3 EXAMPLE IN USING A LINEAR AXIS AS THE BASE AXIS ................................................. 335 10.4 EXAMPLE IN USING A ROTATION AXIS AS THE BASE AXIS ........................................... 339 11. PLC CONSTANTS ........................................................................................................................... 340 11.1 PLC TIMER............................................................................................................................. 340 11.2 PLC COUNTER ...................................................................................................................... 340 11.3 PLC CONSTANTS.................................................................................................................. 341 11.4 SELECTING THE PLC BIT..................................................................................................... 341 12. MACRO LIST.................................................................................................................................... 344

- iii -

13. POSITION SWITCH.......................................................................................................................... 346 13.1 OUTLINE OF FUNCTION ...................................................................................................... 346 13.2 CANCELING THE POSITION SWITCH ................................................................................. 348 14. AUXILIARY AXIS PARAMETER SCREEN ..................................................................................... 349

- iv -

EXPLANATION OF ALARMS

1. 1.1

LIST OF ALARMS OPERATION ALARMS

1.

LIST OF ALARMS

1.1 OPERATION ALARMS

(The bold characters are the messages displayed on the screen.) M01 OPERATION ERROR Alarms occurring due to incorrect operation by the operator during NC operation and those by machine trouble are displayed. Details DOG OVERRUN (Dog overrun) When returning to the reference point the near-point detection limit switch did not stop over the dog but overran the dog. Z-AX NO CRSS One of the axes did not pass the Z-phase during the initial reference point return after the power was turned ON. INVALID RET (Invalid return) When manually returning to the reference point the return direction differs from the axis movement direction selected with the AXIS SELECTION key. EXT INTRLK (External interlock) The external interlock function has activated (the input signal is OFF) and one of the axes has entered the interlock state. INTRL INTRLK (Internal interlock) The internal interlock state has been entered. The absolute position detector axis has been removed. A command for the manual/automatic simultaneous valid axis was issued from the automatic mode. Remedy Increase the length of the near-point dog. Reduce the reference point return speed.

Error No. 0001

0002

Move the detector one rotation or more in the opposite direction of the reference point and repeat reference point return.

0003

The selection of the AXIS SELECTION keys +/ direction is incorrect. The error is canceled by feeding the axis in the correct direction.

0004

As the interlock function has activated release it before resuming operation. Check the sequence on the machine side. Check for broken wires in the interlock signal line. The servo OFF function is valid so release it first. An axis that can be removed has been issued so perform the correct operations. The command is issued in the same direction as the direction where manual skip turned ON so perform the correct operations. During the manual/automatic simultaneous mode the axis commanded in the automatic mode became the manual operation axis. Turn OFF the manual/ automatic valid signal for the commanded axis. Turn ON the power again and perform absolute position initialization.

0005

I-1

1. 1.1

LIST OF ALARMS OPERATION ALARMS

Error No. 0006

Details H/W STRK END (H/W stroke end) The stroke end function has activated (the input signal is OFF) and one of the axes is in the stroke end status. S/W STRK END (S/W stroke end) The stored stroke limit I II IIB or IB function has activated. Chuck/tail-stock barrier stroke end axis found The chuck/tail-stock barrier function turned ON and an axis entered the stroke end state. Reference point return number illegal Return to the No. 2 reference point was performed before return to the No. 1 reference point was completed. Sensor signal illegal ON The sensor signal was already ON when the tool measurement mode (TLM) signal was validated. The sensor signal turned ON when there was no axis movement after the tool measurement mode (TLM) signal was validated. The sensor signal turned ON at a position within 100m from the final entry start position.

Remedy Move the machine manually. Check for broken wires in the stroke end signal wire. Check for trouble in the limit switch. Move it manually. If the stored stroke limit in the parameter is incorrectly set correct it. Reset the alarm with reset and move the machine in the reverse direction.

0007

0008

0009

Execute No. 1 reference point return.

0019

Turn the tool measurement mode signal input OFF, and move the axis in a safe direction. The operation alarm will turn OFF even when the sensor signal is turned OFF. Note) When the tool measurement mode signal input is turned OFF, the axis can be moved in either direction. Pay attention to the movement direction.

0020

Reference point return illegal Return to the reference point was performed before the coordinates had not been established. Zero point return disabled during absolute position detection alarm A zero point return signal was input during an absolute position detection alarm. Zero point return disabled during zero point initialization A zero point return signal was input during zero point initialization of the absolute position detection system.

Execute reference point return

0024

Reset the absolute position detection alarm and then perform zero point return.

0025

Complete zero point initialization and then perform zero point return.

I-2

1. 1.1

LIST OF ALARMS OPERATION ALARMS

Error No. 0050

Details Chopping axis zero point return incomplete The chopping axis has not completed zero point return before entering the chopping mode. All axes interlock will be applied. Synchronization error too large The synchronization error of the master and slave axes exceeded the allowable value under synchronous control. A deviation exceeding the synchronization error limit value was found with the synchronization deviation detection.

Remedy Reset or turn the chopping signal OFF, and then carry out zero point return.

0051

Select the correction mode and move one of the axes in the direction in which the errors are reduced. Increase the allowable value or reset it to 0 (check disabled). When using simple C-axis synchronous control, set the contents of the R435 register to 0. Check the parameter (#2024 synerr). Check for a broken wire in the input mode signal wire. Check for trouble in the mode selector switch. Check the sequence program. Set the switch to a value other than zero to release the error. If the switch is set to a value other than zero check for a short circuit in the signal wire. Check the sequence program. Set the switch to a value other than zero to release the error. If the switch is set to a value other than zero check for a short circuit in the signal wire. Check the sequence program. Set the F1-digit feedrate on the setup parameter screen.

0101

NOT OP MODE (Not operation mode)

0102

OVERRIDE ZERO (Override zero) The cutting feed override switch on the machine operation panel is set to zero.

0103

EX F SPD ZRO (External feed speed zero) The manual feed speed switch on the machine operation panel is set to zero when the machine is in the jog mode or automatic dry run mode. F1 SPD ZRO (F1-digit speed zero) The F1-digit feedrate is set to zero when the F1-digit feed command is being executed. SPINDLE STP (Spindle stop) The spindle stopped during the synchronous feed command.

0104

0105

Rotate the spindle. If the workpiece is not being cut start dry run. Check for a broken wire in the spindle encoder cable. Check the connections for the spindle encoder connectors. Check the spindle encoder pulse.

I-3

1. 1.1

LIST OF ALARMS OPERATION ALARMS

Error No. 0106

Details HNDL FD NOW (Handle feed axis No. illegal) An axis not found in the specifications was designated for handle feed or the handle feed axis was not selected. SPDL RPM EXS (Spindle rotation speed excessive) The spindle rotation speed exceeded the axis clamp speed during the thread cutting command. Fixed point mode feed axis No. illegal: An axis not found in the specifications was designated for the fixed point mode feed or the fixed point mode feedrate is illegal. BLK ST INTLK (Block start interlock) An interlock signal that locks the start of the block has been input. CTBL ST INTLK (Cutting block start interlock) An interlock signal that locks the start of the cutting block has been input. Restart switch ON The restart switch was turned ON before the restart search was completed, and the manual mode was selected. Program Check Mode The automatic start button was pressed during program check or in program check mode. Automatic start during buffer correction The automatic start button was pressed during buffer correction. RESETTING The automatic start button was pressed during resetting or tape rewinding.

Remedy Check for broken wires in the handle feed axis selection signal wire. Check the sequence program. Check the No. of axes listed in the specifications. Lower the commanded spindle rotation speed.

0107

0108

Check for broken wires in the fixed mode feed axis selection signal wire and fixed point mode feedrate wire. Check the fixed point mode feed specifications. Check the sequence program.

0109

0110

Check the sequence program.

0111

Search the block to be restarted. Turn OFF the restart switch.

0112

Press the reset button to cancel the program check mode.

0113

Press the automatic start button after buffer correction is completed.

0115

When rewinding the tape wait for the winding to end or press the reset button to stop the winding and then press the automatic start button. During resetting wait for resetting to end and then press the automatic start button.

I-4

1. 1.1

LIST OF ALARMS OPERATION ALARMS

Error No. 0117

Details PLAYBACK NOT POSSIBLE The playback switch was turned ON during editing or full-character mode (9-inch).

Remedy During editing cancel the function by pressing the input or previous screen key and then turn ON the playback switch. Set the edit screen (9-inch) to the half-character mode and then turn ON the playback switch. Check the program. Set the normal line control axis turning speed. (Parameter #1523 C_feed) Set the C axis turning diameter smaller than the arc radius, or check the setting value of the C axis turning diameter. (Parameter #8041 C rot. R)

0118

Block joint turn stop during normal line control The turning angle at the block joint exceeded the limit during normal line control. Normal line control type I The normal line control axis turning speed (#1523 C_feed) has not been set. Normal line control type II When turning in the inside of the arc, the parameter #8041 C-rot.R setting value is larger than the arc radius.

0120

Synchronization correction mode ON The synchronous correction mode switch was pressed in a non-handle mode. No synchronous control option The synchronous control system (register R435) was set with no synchronous control option. Computer link B The cycle start was attempted before resetting was completed. The operation of the computer link B was attempted in the 2nd part system of the 2-part system.

Select the handle or manual feed mode. Turn OFF the correction mode switch.

0121

Set 0 in register R435.

0123

Perform the cycle start after resetting is completed. Set 0 in #8109 HOST LINK, and then set 1 again before performing the cycle start. The operation of the computer link B cannot be performed in the 2nd part system of the 2-part system. Turn the inclined axis and basic axis start OFF for both axes. (This also applied for manual/automatic simultaneous start.) Invalidate the basic axis compensation, or command one axis at a time.

0124

Simultaneous axis movement prohibited during inclined axis control valid The basic axis corresponding to the inclined axis was started simultaneously in the manual mode while the inclined axis control was valid. Program restart machine lock Machine lock was applied on the return axis while manually returning to the restart position.

0126

Release the machine lock before resuming operations.

I-5

1. 1.1

LIST OF ALARMS OPERATION ALARMS

Error No. 0150

Details Chopping override zero

Remedy Check the chopping override (R135). Check the rapid traverse override (R134). Reset, or turn OFF the chopping signal. When the chopping signal is turned OFF, the axis will return to the reference position, and then the program movement command will be executed.

0151

Command axis chopping axis A chopping axis movement command was issued from the program during the chopping mode. (This alarm will not occur when the movement amount is commanded as 0.) (All axes interlock state will be applied.) Bottom dead center position zero The bottom dead center position is set to the same position as the upper dead center position. Chopping axis handle selection axis Chopping was started when the chopping axis was selected as the handle axis. Axis with no maximum speed set for the outside of the soft limit range Returned from the outside of the soft limit range for the axis with no maximum speed set for the outside of the soft limit range. An attempt was made to execute G114.* during execution of G114.*. G51.2 was commanded when the G51.2 spindle-spindle polygon machining mode was already entered with a separate system.

0153

Correctly set the bottom dead center position.

0154

Select an axis other than the chopping axis as the handle axis, or start chopping after changing the mode to another mode. Set the maximum speed for the outside of the soft limit range. (Parameter #2021 out_f) Change the soft limit range. (Parameter #2013 OT #2014 OT+)

0160

1005

Issue G113 to cancel G114.*. Issue the spindle synchronous cancel signal (Y2E8: SPSYC) to cancel G114.*. Cancel with G50.2. Cancel with the spindle-spindle polygon cancel signal (Y359). Cancel synchronized tapping.

1007

The spindle is being used in synchronized tapping. Spindle C axis and other position control were commanded simultaneously. C axis mode command was issued for polygon machining spindle. C axis mode command was issued for synchronized tapping spindle. Polygon command was issued for synchronized tapping spindle. Spindle is being used as spindle/C axis.

1026

Cancel the C axis command. Cancel the polygon machining command. Cancel the C axis with servo OFF.

I-6

1. 1.1

LIST OF ALARMS OPERATION ALARMS

Error No. 1030

Details Synchronization mismatch Different M codes were commanded in the two systems as the synchronization M codes. Synchronization with the "!" code was commanded in another system during M code synchronization. Synchronization with the M code was commanded in another system during synchronization with the "!" code.

Remedy Correct the program so that the M codes match. Correct the program so that the same synchronization codes are commanded.

1031

The C axis selection signal was changed when multiple C axes could not be selected. An axis that cannot be controlled as the multiple C axes selection was selected.

Check and correct the parameters and program.

1032

Tap return spindle selection illegal during multi-spindle Tap return was executed when a different spindle was selected. Cutting feed will wait until synchronization is completed. Spindle-spindle polygon (G51.2) cutting interlock Cutting feed will wait until synchronization is completed. Cross machining command illegal Cross machining control exceeding the number of control axes was attempted. Cross machining control with duplicated axis addresses was attempted.

Select the spindle for which tap cycle was halted before the tap return signal was turned ON.

1033

Wait for synchronization to end.

1034

Check the parameter settings for cross machining control.

1035

Cross machining control disable modal Cross machining control was commanded for a system in which cross machining control is disabled as shown below. During nose R compensation mode During pole coordinate interpolation mode During cylindrical interpolation mode During balance cut mode During fixed cycle machining mode During facing turret mirror image

Check the program.

I-7

1. 1.1

LIST OF ALARMS OPERATION ALARMS

Error No. 1036

Details Synchronous control designation disable The synchronous control operation method selection (R435 register) was set when the mode was not the C axis mode. The synchronous control operation method selection (R435 register) was set in the zero point not set state. Mirror image disable state The external mirror image or parameter mirror image was commanded during facing turret mirror image.

Remedy Set the R435 register to 0.

Check the program and parameters.

1037

Synchronous control was started or canceled when synchronous control could not be started or canceled. A movement command was issued to a synchronous axis in synchronous control. Spindle synchronous phase calculation illegal The spindle synchronization phase alignment command was issued while the spindle synchronization phase calculation request signal was ON.

Check the program and parameters.

1038

Check the program.

1106

Check the program. Check the sequence program.

(The bold characters are the messages displayed on the screen.) M90 PARAM SET MODE Error No. M90 Messages output when the setup parameter lock function is enabled are displayed. Details Setup parameter lock released The setup parameter lock is released. Automatic start is disabled when setup parameters can be set. Remedy Refer to the manual issued by the machine manufacturer.

I-8

1. 1.2

LIST OF ALARMS STOP CODES

1.2 STOP CODES

These codes indicate a status that caused the controller to stop for some reason. (The bold characters are the messages displayed on the screen.) T01 CANT CYCLE ST Error No. 0101 This indicates the state where automatic operation cannot be started when attempting to start it from the stop state. Details AX IN MOTION (axis in motion) Automatic start is not possible as one of the axes is moving. READY OFF Automatic start is not possible as the NC is not ready. RESET ON Automatic start is not possible as the reset signal has been input. Remedy Try automatic start again after all axes have stopped.

0102

Another alarm has occurred. Check the details and remedy.

0103

Turn OFF the reset input signal. Check that the reset switch is not ON constantly due to trouble. Check the sequence program. Check the FEED HOLD switch. The feed hold switch is the B contact. Check for broken wires in the feed hold signal wire. Check the sequence program. If one of the axis ends is at the stroke end move the axis manually. Check for broken wire in the stroke end signal wire. Check for trouble in the stroke end limit switch. Move the axis manually. If an axis is not at the end check the parameter details. Select the automatic operation mode. Check for broken wires in the automatic operation mode (memory tape MDl) signal wire.

0104

A-OP STP SGL (Automatic operation stop signal ON) The FEED HOLD switch on the machine operation panel is ON (valid).

0105

H/W STRK END (H/W stroke end axis) Automatic start is not possible as one of the axes is at the stroke end.

0106

S/W STRK END (S/W stroke end axis) Automatic start is not possible as one of the axes is at the stored stroke limit. NO OP MODE (NO operation mode) The operation mode has not been selected.

0107

I-9

1. 1.2

LIST OF ALARMS STOP CODES

Error No. 0108

Details OP MODE DUPL (Operation mode duplicated) Two or more automatic operation modes are selected.

Remedy Check for a short circuit in the mode selection signal wire (memory tape MDl). Check for trouble in the switch. Check the sequence program. Return to the original automatic operation mode and start automatic start. Begin automatic start after the tape search is completed.

0109

OP MODE SHFT (Operation mode shift) The automatic operation mode changed to another automatic operation mode. Tape search execution Automatic start is not possible as tape search is being executed. Program restart position return incomplete Automatic start is not possible as the axis has not been returned to the restart position. Thermal alarm Automatic start is not possible because a thermal alarm (Z53 TEMP. OVER) has occurred. In host communication Automatic start cannot be executed as the NC is communicating with the host computer. Disabled start during absolute position detection alarm A start signal was input during an absolute position detection alarm. Disabled start during zero point initialization A start signal was input while initializing the absolute position detectors zero point. Automatic start disabled Automatic start is disabled because setup parameters can be set. Automatic start disabled Automatic start was caused during file deletion or writing.

0110

0112

Manually return to the restart position. Turn the automatic restart valid parameter ON, and then execute automatic start. The NC controller temperature has exceeded the specified temperature. Take appropriate measures to cool the unit. Execute automatic start after the communication with the host computer is completed.

0113

0115

0138

Reset the absolute position detection alarm and then input the start signal.

0139

Complete zero point initialization before inputting the start signal.

0190

Refer to the manual issued by the machine manufacturer.

0191

Cause automatic start after file deletion or writing is completed.

I - 10

1. 1.2

LIST OF ALARMS STOP CODES

T02 FEED HOLD Error No. 0201

The feed hold state been entered due to a condition in the automatic operation. Details H/W STRK END (H/W stroke end axis) An axis is at the stroke end. Remedy Manually move the axis away from the stroke end limit switch. The machining program must be corrected. Manually move the axis. The machining program must be corrected. The program execution position has returned to the start of the program. Execute automatic operation from the start of the machining program. Resume automatic operation by pressing the CYCLE START switch.

0202

S/W STRK END (S/W stroke end axis) An axis is at the stored stroke limit.

0203

RESET SIGNAL ON (Reset signal on) The reset signal has been input.

0204

AUTO OP STOP (Automatic operation stop) The FEED HOLD switch is ON. AUTO MD CHING (Automatic mode change) The operation mode changed to another mode during automatic operation. Acceleration and deceleration time constants too large The acceleration and deceleration time constants are too large. (This problem occurs at the same time as system alarm Z59.) Absolute position detection alarm stop An absolute position detection alarm occurred.

0205

Return to the original automatic operation mode and resume automatic operation by pressing the CYCLE START switch. Increase the set value of the parameter #1206 G1bF. Decrease the set value of the parameter #1207 G1btL. Lower the cutting speed.

0206

0215

Reset the absolute position detection alarm.

I - 11

1. 1.2

LIST OF ALARMS STOP CODES

T03 BLOCK STOP Error No. 0301

This indicates that automatic operation stopped after executing one block of the program. Details Remedy Automatic operation can be resumed by turning the CYCLE START switch ON.

SNGL BLK ON (Single block on) The SINGLE BLOCK switch on the machine operation panel is ON. The single block or machine lock switch changed.

0302

User macro stop The block stop command was issued in the user macro program. Mode change The automatic mode changed to another automatic mode.

Automatic operation can be resumed by turning the CYCLE START switch ON.

0303

Return to the original automatic operation mode and resume automatic operation by turning the CYCLE START switch ON. Set MDI again and turn the CYCLE START switch ON to resume MDl operation. Check the sequence program.

0304

MDI completion The last block of MDI was completed.

0305

Block start interlock The interlock signal that locks the block start is entered. Block cutting start interlock The interlock signal that locks the block cutting start is entered. Offset change of inclined Z-axis during program operation Whether to validate the offset of the inclined Z-axis switched during program operation.

0306

Check the sequence program.

0310

Automatic operation can be restarted by turning ON the cycle start switch.

T04 COLLATION STOP Error No. 0401

Collation stop was applied during automatic operation. Details Remedy Automatic operation can be restarted with automatic start.

Collation stop occurred.

I - 12

1. 1.2

LIST OF ALARMS STOP CODES

T10 FIN WAIT

This indicates the operation state when an alarm did not occur during automatic operation and nothing seems to have happened. Details The error number is displayed while each of the completion wait modes listed in the table below is ON. It disappears when the mode is canceled.
0

Error No. 0

Alarm No.

Unclamp In dwell signal execuwait tion Note 2)

Alarm No.

Door open

Note 1)

Waiting for spindle position to be looped

Alarm No.

Waiting for spindle orientation to complete

Waiting for cutting speed deceleration

Waiting for rapid traverse deceleration

Waiting for MSTB completion

0 1 8 9

0 1 8 9

0 1 2 3 4 5 6 7 8 9 A B C D E F

Note 1: This mode is enabled by the door interlock function. Note 2: The system is waiting for the index table indexing unclamp signal to turn ON or OFF

I - 13

1. 1.3

LIST OF ALARMS SERVO ALARMS

1.3 SERVO ALARMS

These alarms describe errors in the servo system such as the servo drive amplifier motor and encoder. The alarm message alarm No. and Axis Name will display on the alarm message. The No. of the axis where the alarm occurred and the alarm No. will also display on the servo monitor screen. If several alarms have occurred a max. of two errors per axis will display on the servo monitor screen. If S, T, M or N is displayed as an axis name on the alarm message screen, the error is a spindle alarm. Refer to the section Spindle alarms. (The bold characters are the messages displayed on the screen.)

SERVO ALARM

0 0
Axis name Alarm No. Alarm reset class Alarm class

(Note 1) The alarm class and alarm reset class combinations are preset. (Refer to the separate table for S02, S51 and S52.) Alarm class S01 S03 S04 Alarm reset class PR NR AR Resetting methods After removing the cause of the alarm, reset the alarm by turning the NC power ON again. After removing the cause of the alarm, reset the alarm by inputting the NC RESET key. After removing the cause of the alarm, reset the alarm by turning the servo drive unit power ON again.

(Note 2) The resetting method may change according to the alarm class. For example, even if S03 Servo error: NR is displayed, it may be necessary to turn the NC power ON again. (Note 3) Refer to the spindle alarms if the axis name is S, T, M or N. Alarm No. 10 11 Name Insufficient voltage Axis selection error Meaning PN bus voltage dropped to 200 V or lower. The rotary switches for both axes are set to the same axis number when using the 2-axis integrated amplifier. Otherwise, the switches are set to an illegal value. Memory error 1 An error occurred in a memory or FB IC by self-check to be made during driver power-ON. Software processing The S/W process did not end within the specified time. (S/W error 1 operation sequence or timing error) Software processing The control IC is not operating correctly. error 2 Memory error 2 Amplifier self-diagnosis error (The amplifier LED display will be - .)

12 13 14 15

I - 14

1. 1.3

LIST OF ALARMS SERVO ALARMS

Alarm No. 16

17

18

1A

1B

1C

1D 1E

1F

20 21 22 24 25

26

27

An error occurred in the A/D converter for current detection by self-check to be made during driver power-ON. A/D converter variables contain an abnormal value. Motor side detector: The absolute position data was not sent properly with serial data when the power was turned ON. Initial communication error Initial communication with the detector could not be performed. Initial communication with the detector cannot be performed in the Machine side system that uses OHA25K-ET in the machine end detector. detector: Initial communication error In the high-speed serial detector connected to the machine end, an Machine side detector: CPU error error occurred in the data stored in an EEROM. 1 In the high-speed serial detector connected to the machine end, a Machine side deteriorated LED was detected. detector: EEPROM/LED error Machine side In the high-speed serial detector connected to the machine end, an detector: Data error error occurred in a position within one rotation. In the high-speed serial detector connected to the machine end, the Machine side built-in thermal protector functioned. detector: Memory error Machine side In the high-speed serial detector connected to the machine end, detector: communication with the detector stopped. Communication error Motor side detector: An abnormality was detected in the ABZ or UVW phase for the motor No signal 1 end detector. Machine side An abnormality was detected in the ABZ phase in a closed-loop detector: No signal 2 system. LSI error LSI operation error Grounding A grounded motor cable was detected. (Detected only in Ready ON state) Absolute position The absolute position data in the detector was lost. data lost (The backup voltage in the absolute position detector dropped. The absolute position cannot be corrected.) Unused axis error A power module error occurred in the axis set as [F] in the rotary switch. (Alarm issued only for 2-axis amplifier.) The CPU in the machine end absolute position detection linear scale Machine side detector: CPU error is malfunctioning. 2

Name Magnetic pole position detection error A/D converter error

Meaning An error occurred in the U, V, and W phases for polarity position detection.

I - 15

1. 1.3

LIST OF ALARMS SERVO ALARMS

Alarm No. 28

29

2A

2B

2C 2D 2F

30 31 32

33 34

35 36

37 38

39

Name Meaning Machine side The absolute position linear scale moved more than 45 mm/s during detector: Overspeed initialization after the NC power was turned ON. (Alarm output by linear scale.) An error occurred in the scale or scale circuit for the absolute value Machine side linear scale. detector: Absolute (Alarm is output from the linear scale.) position data error The absolute position linear scale has exceeded the maximum Machine side movement speed. detector: Relative (Alarm is output from the linear scale.) position data error Motor side detector: Detector circuit error CPU error 1 In the motor end high-speed serial detector, an error occurred in the data stored in an EEROM. The scale CPU doesnt operate properly. (Alarm is output from the linear scale.) Motor side detector: A deteriorated LED was detected in the detector. EEPROM/LED error Motor side detector: A detector position data error was detected. Data error Motor side detector: Communication with the detector stopped or receive data was abnormal. Communication error Over regeneration Overheating was detected in the regenerative resistor. Overspeed A speed exceeding the motors tolerable rotation speed was detected. Power module The overcurrent protector in the power module functioned. overcurrent An error occurred in the IPM used in the inverter. One of the following factors can be considered. (1) Overcurrent (2) Overheat (3) Drop in control power voltage etc. Overvoltage The PN bus voltage exceeded 400 V. An error occurred in the communication data from the NC. NC-DRV communication: CRC error NC command error The movement command data from the NC is abnormally large in amount. Communication from the NC stopped. NC-DRV communication: Communication error Initial parameter The servo parameter sent from the controller during initialization by error NC power-ON was illegal. There was a protocol error in the communication with the NC. NC-DRV (Frame error) communication: Protocol Error 1 There was a protocol error in the communication with the NC. NC-DRV (Information error) communication: Protocol Error 2

I - 16

1. 1.3

LIST OF ALARMS SERVO ALARMS

Alarm No. 3A 3B 3C 42 43

46 48 49

4A

4B

4F 50

51

52

53

A feedback pulse skip or Z-phase error occurred in the position detector. Feedback error 2 There is an excessive difference in the feedback amount between the motor end detector and the machine end detector during a closed loop. An FB IC error was also detected during semi-closed loop. Motor overheat The motor overheated. Motor side detector: When using the linear servo system, the CPU in the absolute CPU error 2 position linear scale is malfunctioning. Motor side detector: When using the linear servo system, the absolute position linear Overspeed scale detected a speed exceeding 45m/s when the CNC power was turned ON. Motor side detector: When using the linear servo system, the absolute position linear scale detected an error in the scale or scale circuit. Absolute position data error Motor side detector: When using the linear servo system, the absolute position linear scale detected a speed exceeding the maximum movement speed of Relative position the absolute position scale. data error Instantaneous A momentary power interrupt of 50 ms or longer was detected. power interruption Overload 1 Excessive loads were applied for an interval exceeding the specified time. The load level of the servomotor or servo driver can be calculated from the motor current. This load level has reached the overload level that is specified by the overload detection level (sv022: OLL) and overload-time constant (sv021: OLT). Overload 2 Excessive loads are applied, exceeding the specified time. A current command exceeding 95% of the maximum driver capacity continued for 1.0 second or more. Excessive error 1 The difference between the ideal and actual positions has exceeded parameter setting value sv023: OD1 (or sv053: OD3) when the servo was turned ON. Excessive error 2 The difference between the ideal and actual positions has exceeded parameter setting value sv026: OD2 when the servo was turned OFF.

Name Overcurrent Power module overheat Regeneration circuit error Feedback error 1

Meaning The motor drive current is too large. An overheat in the IPM used for the servo drives main circuit was detected. A regeneration transistor or resistor error was detected.

I - 17

1. 1.3

LIST OF ALARMS SERVO ALARMS

Alarm No. 54

Name Excessive error 3

55

External emergency stop error

58 59 5A 5F 61 62 63 65 67 68 69

6A

Collision detection 1: G0 Collision detection 1: G1 Collision detection 2 External contactor welding Power module The regenerative overcurrent alarm was generated on the power overcurrent supply unit side. (Alarm 1 on the power supply unit.) Frequency error A power frequency error was detected in the power supply unit. (Alarm 2 on the power supply unit.) Supplementary The compensating regenerative error alarm was generated on the regeneration error power supply unit side. (Alarm 3 on the power supply unit.) Rush relay error The rush current error alarm was generated on the power supply unit side. (Alarm 5 on the power supply unit.) Phase interruption The open phase alarm was generated on the power supply unit side. (Alarm 7 on the power supply unit.) Watchdog The watch dog alarm was generated on the power supply unit side. (Alarm 8 on the power supply unit.) Grounding The motor ground fault alarm was generated on the power supply unit side. (Alarm 9 on the power supply unit.) For details refer to the descriptions for the power supply units alarms. External contactor External contactor deposition was detected on the power supply welding unit side. (Alarm A on the power supply unit.)

Meaning When an excessive error or alarm 1 is detected, no motor current flows. This error occurs when the power cable is loose or disconnected or no voltage is applied to the bus. No contactor interrupt command is issued in 30 seconds after an external emergency stop signal is input. Check the settings for the emergency stop input signal and sv036 external emergency stop. An interference or system 1 error was detected in G0 modal (rapid traverse feed) mode. An interference or system 1 error was detected in G1 modal (cutting speed) mode. An interference or system 2 error was detected. An outside contact fused.

I - 18

1. 1.3

LIST OF ALARMS SERVO ALARMS

Alarm No. 6B 6C 6D

Name Rush relay welding Main circuit error Parameter error Power supply PCB combination error Memory error Power supply error

6E 6F

71

73 74 75 76 77 7F

80

Instantaneous power interruption/External emergency stop Over regeneration Overregeneration alarm is generated on the power supply unit side. (Alarm J on the power supply unit.) Regenerative Regeneration resistor overheated alarm is generated on the power resistor overheat supply unit side. (Alarm K on the power supply unit.) Overvoltage Overvoltage alarm is generated on the power supply unit side. (Alarm L on the power supply unit.) External emergency External emergency stop setting abnormal alarm is generated on stop setting error the power supply unit side. (Alarm M on the power supply unit.) Power module Power module or PC board overheated alarm is generated on the overheat power supply unit side. (Alarm n on the power supply unit.) An error was detected when the high-gain mode and normal mode Drive unit power was selected. supply reclose Turn the amplifier power ON again. request If this alarm is detected even after the amplifier power is turned ON again after the alarm 7F is detected, there is an error in the EEPROM. Refer to the MELDAS AC Servo Maintenance Manual for details. Detector converting The MDS-B-HR connected to the motor end detected an incorrect connection or broken cable. unit 1: Connection error

Meaning Rush relay deposition was detected on the power supply unit side. (Alarm b on the power supply unit.) Main circuit error was detected on the power supply unit side. (Alarm c on the power supply unit.) Parameter value abnormal was detected on the power supply unit side. (Alarm d on the power supply unit.) An incorrect power PCB and control PCB combination was detected. (Alarm d on the power supply unit.) (MDS-CH-CV Series only) Memory error was detected on the power supply unit side. (Alarm E on the power supply unit.) AD converter error was detected on the power supply unit side. It was recognized that the power supply is not connected. (Alarm F on the power supply unit.) Momentary power failure detection alarm is generated on the power supply unit side. (Alarm H on the power supply unit.)

I - 19

1. 1.3

LIST OF ALARMS SERVO ALARMS

Alarm No. 81

83

84 85 86

88 89

8A

8C

8D 8E

Name Detector converting unit 1: Communication error Detector converting unit 1: Judgment error Detector converting unit 1: CPU error Detector converting unit 1: Data error Detector converting unit 1: Magnetic Pole error Watchdog Detector converting unit 2: Connection error Detector converting unit 2: Communication error Detector converting unit 2: Judgment error Detector converting unit 2: CPU error Detector converting unit 2: Data error

Meaning The MDS-B-HR connected to the motor end detected an error in the communication with the absolute position detection scale.

The MDS-B-HR connected to the motor end could not judge the connected scale's analog wave cycle. The CPU for the MDS-B-HR connected to the motor end is not operating correctly. An error was detected in the analog interpolation data for the MDS-B-HR connected to the motor end. An error was detected in the magnetic pole data of the MDS-B-HR connected to the motor end. Servo system operation is abnormal. The MDS-B-HR connected to the machine end detected an incorrect connection or broken cable. The MDS-B-HR connected to the machine end detected an error in the communication with the absolute position detection scale.

The MDS-B-HR connected to the machine end could not judge the connected scale's analog wave cycle. The CPU for the MDS-B-HR connected to the machine end is not operating correctly. An error was detected in the analog interpolation data for the MDS-B-HR connected to the machine end.

I - 20

1. 1.3

LIST OF ALARMS SERVO ALARMS

An error was found in the parameters transmitted from the S02 INIT PARAM ERR controller to the spindle amplifier Axis name when the power was turned ON. Remove the cause of the alarm, Alarm No. (parameter No.) and then reset the alarm by turning the controller power OFF once. (Note) Refer to the spindle alarms if the axis name is S, T, M or N. Alarm No. Details Remedy 2201 2264 The servo parameter setting data is illegal. Check the descriptions for the appropriate parameters and correct them. The alarm No. is the No. of the servo parameter where the error occurred. The number of constants to be used in the Check that all the related parameters are 2301 specified correctly. following functions is too large: sv001:PC1, sv002:PC2, sv003:PGN1 Electronic gears sv018:PIT, sv019:RNG1, sv020:RNG2 Position loop gain Speed feedback conversion Check that all the related parameters are High-speed serial incremental detector 2302 Parameters for absolute position detection specified correctly. sv017:SPEC, sv025:MTYP are set to ON during OSE104 and OSE105 connection. Set the parameters for absolute position detection to OFF. To detect an absolute position, replace the incremental specification detector with an absolute position detector. Check that all the related parameters are No servo option is found. 2303 The closed loop (including the ball screw- specified correctly. sv025:MTYP/pen end detector) or dual feedback control sv017:SPEC/dfbx function is an option. No servo option is found. Check that all the related parameters are 2304 The SHG control function is an option. specified correctly. sv057:SHGC sv058:SHGCsp No servo option is found. Check that all the related parameters are 2305 The adaptive filtering function is an option. specified correctly. sv027:SSF1/aflt

I - 21

1. 1.3

LIST OF ALARMS SERVO ALARMS

S51

PARAMETER ERROR

Axis name Alarm No. (parameter No.)

A warning appears if a parameter set outside the tolerable range is set. Illegal settings will be ignored. This alarm will be reset when the correct value is set.

(Note) Refer to the spindle alarms if the axis name is S, T, M or N. Alarm No. Details Remedy Check the descriptions for the appropriate 2201 2264 Servo parameter setting data is illegal. The alarm No. is the No. of the servo parameters and correct them. parameter where the warning occurred. The servo warning is displayed.

S52

SERVO WARNING

0 0 Axis name Alarm No. (Warning No.)

(Note) Refer to the spindle alarms N. Alarm No. Name Detector: Initial 90 communication error Detector: 91 Communication error Detector: Protocol 92 error Initial absolute 93 position fluctuation Scale feedback 96 error Scale offset error 97 9B

if the axis name is S, T, M or Meaning Initial communication with the absolute position linear scale cannot be performed. An error occurred in communication with the detector in the absolute position detector. An error occurred in the data from the detector in the absolute position detector. The absolute position data fluctuated when the power was turned ON so the absolute value counter could not be set. There is an excessive difference in the feedback amount between the motor end detector and the MP scale in the absolute position detector. An error occurred in the offset data to be read during initialization by NC power-ON in the absolute position detector of the MP scale. When using the linear servo system, an error was detected in the magnetic pole shift amount set in sv028.

9C

Detector converting unit: Magnetic pole shift warning When using the linear servo system, an error was detected in the Detector magnetic pole data of the MDS-B-HR connected to the MAIN side converting unit: after the Z phase was passed. Magnetic pole warning

I - 22

1. 1.3

LIST OF ALARMS SERVO ALARMS

Alarm No. 9E

9F E0 E1

Name Absolute position detector: Revolution counter error Battery voltage drop Over regeneration warning Overload warning

E3 E4 E6

E8

E9

EA

EB

Absolute position counter warning Set parameter warning Control axis detachment warning Excessive supplementary regeneration frequency Instantaneous power interruption warning In external emergency stop state Over regeneration warning

Meaning An error occurred in the rotation counter in the detector. An error occurred in the rotation counter in OSE104/OSA104/OSE105/OSA105/OSE104-ET/OSA104-ET/OSE1 05-ET/OSA105-ET. The absolute position cannot be corrected. The voltage of the battery supplying to the absolute value detector dropped. An 80% level of the regeneration alarm was detected. (The regeneration alarm may occur if operation is continued.) An 80% level of the overload 1 alarm was detected. This is not an alarm so the servo will not turn OFF but if operation is continued overload 1 alarm may occur. There is a difference between absolute and relative position data. A parameter setting exceeding the setting range was set. A control axis removal command has been issued. (Status display)

The auxiliary regeneration cycle was too high in the power supply unit. (Alarm o from the power supply unit)

A momentary power interrupt of 25 to 50 ms occurred. (Alarm p from the power supply unit.) The power supply enters an emergency stop state by receiving the stop signal from the NC. (Alarm q from the power supply unit) An excessive-regeneration alarm was generated from the power supply unit. (Alarm r from the power supply unit.)

I - 23

1. 1.4

LIST OF ALARMS SPINDLE ALARMS

1.4 SPINDLE ALARMS

These alarms describe errors in the spindle system such as the spindle amplifier motor and encoder. The alarm message, alarm number, and axis name (S: 1st spindle, T: 2nd spindle, M: 3rd spindle, N: 4th spindle) will display on the alarm message screen. If several alarms have occurred, the number of the alarm that occurred last and the other alarm numbers will display on the spindle monitor screen for confirmation. If an axis name other than S, T, M and N is displayed, the alarm is a servo alarm. Refer to the section Servo alarms. (The bold characters are the messages displayed on the screen.)

SERVO ALARM

0 0
Axis name Alarm No. Alarm reset class Alarm class

(Note 1) The alarm class and alarm reset class combinations are preset. (Refer to the separate table for S02, S51 and S52.) Alarm class S01 S03 S04 Alarm reset class PR NR AR Resetting methods After removing the cause of the alarm, reset the alarm by turning the NC power ON again. After removing the cause of the alarm, reset the alarm by inputting the NC RESET key. After removing the cause of the alarm, reset the alarm by turning the servo drive unit power ON again.

(Note 2) The resetting method may change according to the alarm class. For example, even if S03 Servo error: NR is displayed, it may be necessary to turn the NC power ON again. (Note 3) Refer to the servo alarms if the axis name is other than S, T, M and N. Alarm No. 12 13 16 Name Memory error 1 Software processing error 1 Magnetic pole position detection error Meaning A check sum or RAM check error occurred in the ROM of the spindle drives control card. The S/W process did not end within the specified time.

17 20

The start signal was input before the Z-phase of the magnetic pole position was automatically adjusted. Or, the number of initial magnetic pole estimation retry times (10 times or more) was exceeded. (After replacing the spindle amplifier, set parameter (SP205: ZCHS) to 1 from 0, carry out Z phase automatic adjustment, and then turn the power ON again.) A/D converter error The AD converter for current detection did not function normally during initialization. A signal was not input from the PLG or was not at a normal level. Motor side detector: No signal 1

I - 24

1. 1.4

LIST OF ALARMS SPINDLE ALARMS

Alarm No. 21

23

Name Machine side detector: No signal 2 Excessive speed error 1

Meaning A signal was not input from the spindle encoder (for orient C axis) or was not at a normal level. The command speed and motor speed difference was above the specified value and the state continued for the specified time. This may also occur when the coil changeover contactor is not the specified contactor. Overheating was detected in the regenerative resistor. The motor speed exceeded 115% of the set max. speed. A current exceeding the specified value flowed to the spindle drives main circuit. This may also occur when the coil changeover contactor is not the specified contactor. The bus voltage in the driver exceeded 400V. This may also occur when the coil changeover contactor is not the specified contactor. A CRC error occurred in the communication data from the controller.

30 31 32

Over regeneration Overspeed Power module overcurrent

33

Overvoltage

34

35 36

37 38

39

3A 3B 3D

3E

NC-DRV communication: CRC error NC command error The movement command data from the controller is abnormally high during position control. NC-DRV The periodic data transmission from the controller was stopped. communication: Communication error Initial parameter The servo parameter sent from the controller during initialization of the error driver was illegal. NC-DRV There was a protocol error in the communication with the controller. communication: (Frame error) Protocol error 1 NC-DRV There was a protocol error in the communication with the controller. communication: (Information error) Protocol error 2 Overcurrent The command current reached the spindle drive's maximum output current and continued for one second or more. Power module An overheat in the IPM used for the drivers main circuit was detected. overheat Spindle motor A state in which the motor speed did not reach 45r/min or more even locked when the maximum torque command value reached the time set in the parameter SP239 (3 seconds when set to 0) was detected. Spindle speed 1. A state in which the motor was continuously accelerated even overrun when the speed feedback exceeded 112.5% (detection speed) of the commanded speed was detected. (Note that if a speed less than the parameter SP237 (1000r/min when set to 0) setting is commanded, the detection speed will be the speed command value + SP2371.125.) 2. Motor rotation exceeding the value set with parameter SP206 (when set to 0: 10 deg.) was detected even though the speed command was 0 (including when stopped during position control).

I - 25

1. 1.4

LIST OF ALARMS SPINDLE ALARMS

Alarm No. 3F

Name Excessive speed error 2

40 41

42

43 44

46 4E

50 51 52 5C

Meaning The state in which the speed range set by parameter SP238 (30% when set to 0) was exceeded while rotating at a constant speed with speed control exceeded the time set in parameter SP239 (3 seconds when set to 0). Detector selection The procedure for changing the signal during use of the TK unit is unit switching error wrong. Detector selection Communication with the TK unit during use of the TK unit was incorrect. unit communication error Feedback error 1 1. A PLG error was detected during PLG automatic compensation. 2. The correct Z phase was not detected even when the motor rotated several times during Z phase automatic adjustment. 3. An abnormal number of feedback pulses was continuously detected during normal operation. Feedback error 2 A deviation occurred in the feedback from the spindle encoder and motor built-in encoder. When using the coil changeover motor, the C axis mode was entered Inappropriate when the H coil or M coil was selected. winding selected for C axis Motor overheat The motor overheated and the thermal protector functioned during an overload or when the motor cooling blower stopped. NC command The spindle control mode was selected several times. mode error (If the input was unexpected, the mode will return to the speed control mode, and an alarm will occur.) Overload 1 The time that the motor current exceeded the overload detection level exceeds the detection time constant. Overload 2 The motor output reached the overload level set with the overload detection level and detection time constant. Excessive error 1 The position tracking error exceeded the specified value during position loop operation. Orientation When orientation was completed, the error between the command feedback error and feedback exceeded the value set in the parameters. If the number of orientation retry times parameter SP118 is set, S52 SERVO WARNING 00A9 will occur, and then this alarm will occur. (An alarm will occur if the error exceeds SP114: OPER. This cannot be detected when using magnetic sensor orientation, so set SP114 to 0.)

I - 26

1. 1.4

LIST OF ALARMS SPINDLE ALARMS

Alarm No. 5D

Name Speed monitoring: Input mismatch Speed monitoring: Feedback speed error Power supply alarm Watchdog

5E

Meaning This occurs if the door state of the DI input (CN9 10-20) and the data input (control input 4-bit D) signal from the NC do not match. (Occurs if the state does not match for three seconds.) This occurs if the door is opened when the spindle speed is higher than the speed set in parameter SP223: SPDV. The codes 60 to 6F are power supply alarms. The power supply alarms will be displayed as alarms of the axis to which the power supply is connected. Refer to the section Servo alarms for details. 88 is the watch dog alarm. Refer to the section Servo alarms for details.

61 6F

88

S02 INIT PARAM ERR Axis name Alarm No. (parameter No.)

An error was found in the parameters transmitted from the controller to the spindle amplifier when the power was turned ON. Remove the cause of the alarm, and then reset the alarm by turning the controller power OFF once.

(Note) Refer to the servo alarms if the axis name is other than S, T, M and N. Alarm No. Details Remedy Confirm the spindle parameter for the No. 3201 3584 Parameter error displayed as an error. A parameter value not within the tolerable range was set. The alarm No. is Refer to Spindle Drive Maintenance Manuals the No. of the spindle parameter where Alarm No. 37. the error occurred.

S51 PARAMETER ERROR Axis name Alarm No. (parameter No.)

(Note) Refer to the servo alarms if the axis name is other than S, T, M and N. Alarm No. 3201 3584 Details Parameter warning A parameter value not within the tolerable range was set. The alarm No. is the No. of the spindle where the warning occurred.

A warning appears if a parameter set outside the tolerable range is set. Illegal settings will be ignored. This alarm will be reset when the correct value is set.

Remedy Confirm the details of the spindle parameter for which the No. is displayed.

I - 27

1. 1.4

LIST OF ALARMS SPINDLE ALARMS

S52 SERVO WARNING

0 0 Axis name Alarm No. (Warning No.)

The spindle warning is displayed.

(Note) Refer to the servo alarms if the axis name is other than S, T, M and N. Alarm No. A9 Details Orientation feedback warning The system is retrying when an orientation feedback error occurs. (When SP118: ORCT is set to 0, an alarm (5C) will occur instead of the warning.) Over regeneration warning A level of 80% of the excessiveregeneration alarm was detected (continuing the operation may cause the excessive-regeneration alarm). Overload warning The time that the motor current exceeded the overload detection level was 80% or more of the detection time constant. Set parameter warning A parameter exceeding the setting range was set. The illegal parameter will be ignored and the value before the illegal parameter setting will be retained. Remedy Check the speed detector or encoder shield treatment, and for wire breakage. Check the phase of the A, B and Z phases. (Adjust the waveform)

E0

Refer to the Spindle Drive Maintenance Manual.

E1

Refer to the Spindle Drive Maintenance Manual.

E4

Confirm the spindle parameter.

I - 28

1. 1.5

LIST OF ALARMS MCP ALARM

1.5 MCP ALARM

An error has occurred in the drive amplifier and other interfaces. (The bold characters are the messages displayed on the screen.) Y02 SYSTEM ALARM Error No. 0050 0051 An error occurred in the data transmitted between the MCP and amplifier after the power was turned ON. Details Remedy Background error The software or hardware may be damaged. Contact the service center. 0000 CRC error A communication error has occurred between the controller and amplifier. (10 times/910.2 ms) 0001 CRC error (2 continuous times) Take measures against noise. Check that the communication cable 0002 Reception timing error connector between the controller and (2 continuous times) amplifier and one between the amplifiers are Data ID error 03 tight. (2 continuous times) Check whether the communication cable : Axis No. between the controller and amplifier and one between the amplifiers are No. of reception frames error 04 disconnected. (2 continuous times) A driving amplifier may be faulty. Take a : Axis No. note of the 7-segment LED contents of each driving amplifier and report to the Service Center.

Check the amplifier mounting state. Check the end of the cable wiring. Check the cable for broken wires. The amplifier is not correctly Check the connector insertion. connected The amplifier input power is not being input. The amplifier axis No. switch is illegal. Error No. Details Servo axis amplifier not mounted Alphabet (axis name) PLC axis amplifier not mounted 14 No.1 spindle axis not mounted S No.2 spindle axis not mounted T Y03 AMP. UNEQUIPPED

Y05 INIT PARAM ERR : Error parameter number Details Remedy There is a problem in the value set for the number of axes or Check the value set for the corresponding the number of systems. parameters. #1001 SYS_ON #1002 axisno #1039 spinno

I - 29

1. 1.5

LIST OF ALARMS MCP ALARM

Y06 mcp_no ERROR Error No. 0001 0002 0003 0004

There are differences in the MCP and axis parameters when the NC power is turned ON. Details Remedy There is a skipped number in the channels. Check the values set for the following parameters. The random layout setting is duplicated. #1021 mcp_no The amplifier fixed setting 0000 and #3031 smcp_no random layout setting are both set. #3032 mbmcp_no The spindle/C axis #3031 mcp_no and #3032 smcp_no are set to the same values. A random layout is set for the #1154 pdoor =1 two-system. The channel No. parameter is not within the setting range.

0005 0006

Y51 PARAMETER ERROR Error No. 1

9 12

15

16

101

An error occurred in a parameter that causes an alarm while the control axis was operating. Details Remedy Check #2004 G0tL. LN FEED ABNL (Linear feed abnormal) The time constant has not been set or the setting exceeded the setting range. Check #2007 G1tL. CT FEED ABNL (Cutting feed abnormal) The time constant has not been set or the setting exceeded the setting range. DLY F-F ABNL (Delayed fast feed abnormal) Check #2005 G0t1. The time constant has not been set or the setting exceeded the setting range. Check #2008 G1t1. DLY CUTG ABNL (Delayed cutting feed abnormal) The time constant has not been set or the setting exceeded the setting range. GRID SPACE ERROR Check #2029 grspc. Check spindle parameters #3017 stapt1 to SYNCHRONOUS TAP CYCLE #3020 stapt4. ACCELERATION/DECELERATION TIME CONSTANT ERROR The time constant has not been set or the setting exceeded the setting range. Check #2102 skip_tL. LN SKIP ABNL (Linear skip abnormal) The time constant has not been set or the setting exceeded the setting range. Check #2103 skip_t1. DLY SKIP ABNL (Delayed skip abnormal) The time constant has not been set or the setting exceeded the setting range. ROTARY AXIS GEAR RATIO EXCESSIVE Check #2201 PC1 and #2202 PC2. (ABSOLUTE POSITION DETECTION)

I - 30

1. 1.5

LIST OF ALARMS MCP ALARM

Y90 SP. NON SIGNAL

(Alarm No.) 0 0 No.1 spindle No.2 spindle
Alarm No. 1 2 3 4 5 6 7
Z open phase B open phase A open phase

Alarm No. 0001 0007

Details Remedy Check the spindle encoders feedback There is an error in the spindle encoder cable and the encoder. signal. The data transmission to the servo amplifier and spindle amplifier is stopped when this error occurs.

I - 31

1. 1.6

LIST OF ALARMS SYSTEM ALARMS

1.6 SYSTEM ALARMS

The following messages are displayed with the register at the time when the error occurred if the system stops due to a system error. Message Parity error Bus error Zero divide Details RAM error A non-existing memory was accessed. The division with a 0 denominator was attempted. Watch dog The software process is not functioning error correctly. Illegal The alarm was caused by an illegal exception software function not listed above. Address error An illegal memory was accessed. Illegal The software process is not functioning instruction correctly. Stack overflow Remedy Write down the displayed register and contact the service center.

Z31 DATA SERVER ERROR Warning No. Warning No. 0001 0002 0003 0004 0005 0006 0007 0008 000A Explanation Socket open error (socket) Socket bind error (bind) Connection wait queue error (listen) Connection request acceptance error (accept) Data receive error (socket error) Data receive error (data shortage or disconnection) Data send error (socket error) Data send error (data shortage or disconnection) Socket close error (close)

Note: If warning No. 0001, 0002, 0003, or 000A is displayed, set the parameters, then turn power OFF and turn it ON again. Message Z40 FORMAT NOT MET Details Remedy This appears when the parameter MemVal Either return the MemVal setting, or format is formatted at 0, and MemVal is set to 1. and restart.

I - 32

1. 1.6

LIST OF ALARMS SYSTEM ALARMS

The bold characters are the messages displayed on the screen. Message Z51 EE ROM ERROR 000x Details This occurs when the parameters were not correctly written into the EEROM. Formatting of the machine manufacturer macro program area did not end correctly. The machine manufacturer macro program was not written into the FROM correctly. <Type> Z51 ROM error 0001: Open error Z51 ROM error 0002: Erase error Z51 ROM error 0003: Write error Z51 ROM error 0004: Verify error Z52 BATTERY FAULT TEMP. OVER RIO NOT CONNECT The voltage of the battery inserted in Replace the battery of the NC control unit. the NC control unit has dropped. (The After treating the battery check the battery used to save the internal data) machining program Cooling measures are required. The controller or operation board Turn OFF the controller power or lower temperature has risen above the the temperature with a cooler etc. designated value. (Note 1) This occurs when an error occurs in the communication between the controller and remote l/O unit. Cable breakage Remote l/O unit fault Power supply to remote l/O unit fault (Note 2) Z57 SYSTEM WARNING The program memory capacity setting value cannot be formatted. The expansion cassette (HR437) is not mounted after formatting. An expansion cassette different from the expansion cassette (HR437) mounted during formatting is mounted. (Note 3) Z58 ROM WR UNFIN The machine manufacturer macro Write the machine manufacturer macro program was not written to the FROM program to the FROM. after being registered, edited, copied, * If the operations, such as editing, done condensed, merged, the number while the NC power was OFF can be changed, or deleted. invalidated, the program does not need to be written to the FROM. Check the state of the following items. Program memory capacity Status of expansion cassette (HR437) mounting APLC open option Check and replace the cables. Replace the remote I/O unit. Check the power supply. (existence of supply voltage) Remedy If the same alarm is output by the same operation, the cause is an H/W fault. Contact the Service Center. Reformat the area.

Write to the FROM again.

Z53

Z55

I - 33

1. 1.6

LIST OF ALARMS SYSTEM ALARMS

Message Z59 TIME CONSTANT

Details Acceleration and deceleration time constants are too large. (This alarm is output at the same time as T02 FEED HOLD 0206.)

Remedy Increase the value specified as the #1206 G1bF parameter. Decrease the value specified as the #1207 G1btL parameter. Lower the feedrate.

CAUTION If the battery low warning is issued, save the machining programs, tool data and parameters in an input/output device, and then replace the battery. When the battery alarm is issued, the machining programs, tool data and parameters may be destroyed. Reload the data after replacing the battery. Do not replace the battery while the power is ON. Do not short circuit, charge, heat, incinerate or disassemble the battery. Dispose of the spent battery following local laws. Note 1: Temperature warning If the alarm is displayed when an overheat alarm is detected the overheat signal will be output simultaneously. If the machine is in automatic operation the operation will be continued but restarting will not be possible after resetting or stopping with M02/M30. (Starting will be possible after block stop or feed hold.) The alarm will be reset and the overheat signal will turn OFF when the temperature drops below the specified temperature. Z53 TEMP. OVER 000x 0001 : The temperature in the controller is high. 0002 : The temperature around the communication terminal (setting and display unit) is high. 0003 : The temperature in the controller and around the communication terminal (setting and display unit) is high. The ambient temperature must be lowered immediately when a Z53 TEMP.OVER alarm occurs but if machining must be continued the alarm can be invalidated by turning the following parameter OFF.
76543210 PLC parameter bit selection #6449 Communication terminal (setting and display unit) Controller

0: Detection invalid 1: Detection valid

I - 34

1. 1.6

LIST OF ALARMS SYSTEM ALARMS

Note 2: RIO communication interrupt If communication between the control unit and remote I/O unit fails, the alarm and remote I/O unit number are displayed.
(a)(b)

Z55 RIO NOT CONNECT

Board connection remote I/O communication interrupted station

00
Remote I/O 1st system communication interrupted station Remote I/O 2nd system communication interrupted station

(a) and (b) above indicate the following matters.

Alarm number RIO (seventh station) RIO (sixth station) RIO (fifth station) RIO (fourth station) Alarm number

RIO (third station)

RIO (second station)

RIO (first station)

RIO (0th station)

0 1 2 3 4 5 6 7 8 9 A B C D E F

1 2 3 4 5 6 7 8 9 A B C D E F

This applies for both the remote I/O 1st system communication interrupted station and board connection remote I/O communication interrupted station. Note 3: System warning Z57 SYSTEM WARNING 00xx 0000 001x : When the expansion cassette (HR437) is not mounted, a program memory capacity exceeding 1280m was designated. 002x : When the APLC open option was validated, 5120m was designated for the program memory capacity. 00x1 : After formatting the program memory capacity to 1280m or more, the expansion cassette (HR437) was removed, or an expansion cassette (HR437) not used during formatting was mounted. I - 35

1.7

1. LIST OF ALARMS ABSOLUTE POSITION DETECTION SYSTEM ALARMS

1.7 ABSOLUTE POSITION DETECTION SYSTEM ALARMS

Z70 ABS. ILLEGAL This error is displayed if the absolute position data is lost in the absolute position detection system. Alarm reset Zero point when Servo Remedy initialization power is alarm No. turned OFF Complete zero point Required initialization.

(Error No.) (Axis name) Error No. 0001 Details Zero point initialization is incomplete. Otherwise, the spindle was removed. The absolute position reference point data saved in the NC has been destroyed.

0002

0003

0004 0005

0080

0101

0106

Input the parameters. If the reference point data cannot be restored perform zero point initialization. The parameters used to detect Correctly set the parameters. Turn the the absolute position have power on again and been changed. perform zero point initialization. #1003 iunit #2201 PC1 #1016 iout #2202 PC2 #1017 rot #2218 PIT #1018 ccw #2219 RNG1 #1040 M_inch #2220 RNG2 #2049 type #2225 MTYP The zero point initialization Reperform zero point point is not at the grid position. initialization. Restoration was possible with Turn the power on parameter input in the above again and operation will be possible. No.0002 state. The absolute value data was Replace the detector lost, because the multi-rotation and complete zero point initialization. counter data in the detector was incorrect, etc. Reperform zero point The power was turned ON again after the servo alarm No. initialization. 25 displayed. Reperform zero point The power was turned ON again after the servo alarm No. initialization. E3 displayed.

(Required)

Required

Required Not required

Required

(9E) etc.

Required

(25)

Required

(E3)

Note:

To release alarm Z70 ABS. ILLEGAL, enter the parameter data output when establishing the absolute position and turn ON the power again. For the rotation axis, however, the alarm cannot be released by entering the parameter data.

I - 36

1.7

1. LIST OF ALARMS ABSOLUTE POSITION DETECTION SYSTEM ALARMS

Z71 DETECTOR ERROR (Error No.) (Axis name)

Error No. 0001

Details

Remedy

0003

0004

0005

0006

The backup voltage in the Replace the battery absolute position detector check the cable connections and dropped. check the detector. Turn the power ON again and perform zero point initialization. Communication with the Check and replace the absolute position detector cables card or detector. Turn the was not possible. power ON again and perform zero point initialization. Check and replace the The absolute position cables card or data fluctuated when establishing the absolute detector. Turn the power ON again and position. perform zero point initialization. An error was found in the Check and replace the cables card or serial data from the detector. Turn the absolute position power ON again and detector. perform zero point initialization. Operation is possible Servo alarm E3 Absolute position counter until the power is turned off. warning

This alarm is displayed if an error is found in the detector for the absolute position detection system. Alarm reset Zero point when Servo initialization power is alarm No. turned OFF 25 Required (Z70-0101 displays after power is turned ON again.)

(Required) Only when detector is replaced.

Reset

91

(Required) Only when detector is replaced.

Reset

93

(Required) Only when detector is replaced.

Reset

92

0007

Reset (Required) When power is turned ON (Z70-0106 displays again. after power is turned ON again.) Reset Initial communication with Check and replace the (Required) Only when detector is cables card or the absolute position replaced. detector. Turn the detector was not power ON again and possible. perform zero point initialization.

E3

18

I - 37

1.7

1. LIST OF ALARMS ABSOLUTE POSITION DETECTION SYSTEM ALARMS

Z72 COMPARE ERROR

Alarm No.

This alarm is displayed if an error is detected when (Alarm No.) (Axis name) comparing the detectors absolute position and controller coordinate values in the absolute position system. Details Remedy

Z73 ABS. WARNING Alarm No. 0001

This displays a warning in the absolute position (Warning No.) (Axis name) detection system. Details Remedy Servo alarm 9F The battery voltage dropped or a cable is Battery voltage drop broken. Absolute position initialization is not required.

I - 38

1.8

1. LIST OF ALARMS MESSAGES DURING EMERGENCY STOP

1.8 MESSAGES DURING EMERGENCY STOP

EMG EMERGENCY

Error items Refer to the explanations for details.

Error No. PLC EXIN

Details The user PLC has entered the emergency stop state during the sequence process. The emergency stop input signal is significant (open). An alarm occurred in the servo system causing an emergency stop. The user PLC (ladder sequence) is not running.

SRV STOP

SPIN

Spindle amplifier not mounted The spindle amplifier is not mounted.

PC_H

High-speed PC processing abnormal

PARA

Setting of the door open II fixed device is illegal. The dog signal random assignment parameter setting is illegal.

LINK

If the FROM/TO instruction is not executed within 500 ms, an emergency stop occurs. *

Remedy Investigate and remove the cause of the user PLC emergency stop. Cancel the emergency stop input signal. Check the wiring to see if any wiring is broken. Investigate and remove the cause of the servo alarm. Check if the rotary switch CS2 on the top of the controller front panel is set to 1. Check if the PLC edit file save screen (onboard function) [4RUN/SP] (run/stop) switch is turned ON. Cancel the causes of the other emergency stop. Check emergency stop signal input in the spindle amplifier. Check the sequence program. (To stop monitoring the high-speed PC processing temporarily, set 1 in #1219 aux03 bit1. Disable the monitoring function only as a temporary measure.) Specify the #1155 DOOR_m and #1156 DOOR_s parameters correctly. (When the door open II fixed device is not used, set #1155 DOOR_m and #1156 DOOR_s to 100.) Correctly set the #2073 zrn_dog, #2074 H/W_OT+, #2075 H/W_OT-and #1226 aux 10 bit 5 parameters. Try to execute the FROM or TO instruction one or more times every 500 ms. Measure the time in which no interrupt request is issued from MELSEC and store the result in the R register. R1880: Current time-out counter R1881: Counter for maximum time-out after power-on R1882: Counter for maximum time-out after system start-up (backed up)

I - 39

1.8

1. LIST OF ALARMS MESSAGES DURING EMERGENCY STOP

Error No. LINK

WAIT

XTEN LAD

Details MELSEC is held in error and reset states. The contents of MELSEC-specific code area in buffer memory have been destroyed. PLC serial link communication has stopped. Note: When WAIT is entered for the PLC serial link, only the preparation sequence has been established before the communication stops. Therefore, it is supposed that the basic specification parameters or serial link parameters #1902 and #1903 are incorrect or the #1909 set-time Tout (ini) is too short. The preparation sequence is not sent from the master station. Otherwise, the contents of the received preparation sequence are inconsistent with those of the parameters, so that the usual sequence cannot be started. Note: When LINK is also entered for the PLC serial link, refer to Note in the section, LINK. The HR571 card operates abnormally or the rotary switch is set incorrectly. The user PLC (ladder sequence) has an illegal code.

Remedy Check the MELSEC states. Check the MELSEC states.

Check that HR571 card wiring and external sequencer transmission are normal. Check the diagnostic screen for link communication errors. Check whether the basic specification parameters or serial link parameters are specified correctly.

Check that the HR571 card rotary switch and wiring and the external sequencer transmission are normal. Check the diagnostic screen for link communication errors.

Check the HR571 card rotary switch and replace the HR571 card if required. Check the user PLC (ladder sequence) to see if it uses illegal device numbers or constants.

I - 40

1. 1.9

LIST OF ALARMS AUXILIARY AXIS ALARMS

1.9 AUXILIARY AXIS ALARMS

Display example S01 AUX SERVO ALM

Axis No. 1 to 4
Alarm information (Follows MR-J2-CT alarm information)

(1) S01 AUX SERVO ALM Alarm information 0011 0013 PCB error 1 Details An error occurred in the amplifier's internal PCB. Remedy Replace servo amplifier. Replace servo amplifier.

Software An error occurred in the processing amplifier's internal reference timeout, clock error clock. Motor type, Motor type error detector type error Detector initial communication error.

0016

Use a correct amplifier and motor combination. Connect correctly. Replace the motor. Replace or repair cable. Replace the motor (detector).

Detector CPU error 0017 PCB error (A/D conversion initial error) Absolute position lost

An error occurred in the Replace servo amplifier. amplifier's internal A/D converter. An error occurred in the detector's internal absolute position data. Turn the power ON for 2 to 3 minutes while the alarm is occurring, and then turn the power ON again. Replace the battery, and initialize the absolute position again.

0025

0034 0036

CRC error Communication timeout, NC down

An error occurred in the communication with the NC.

Take countermeasures against noise.

Communication with the NC was Connect correctly. cut off. Turn the NC power ON. Replace the amplifier or NC. The parameter setting value is incorrect. An error occurred in the communication with the NC. Undefined data was transferred from the NC. Set the parameter correctly.

0037

Parameter error (Regenerative resistance error) Frame error INFO error

0038 0039

Take countermeasures against noise. Change the NC software version to a compatible version.

I - 41

1. 1.9

LIST OF ALARMS AUXILIARY AXIS ALARMS

(2) S02 AUX SERVO ALM Alarm information 0011 0013 Details PCB error 1 An error occurred in the (drive circuit error) amplifier's internal PCB. Software An error occurred in the processing amplifier's internal reference timeout, clock error clock. EEROM error PCB error (A/D conversion error) PCB error (LSI error) Detector error A write error occurred to the EEROM in the amplifier. Remedy Replace servo amplifier. Replace servo amplifier.

0015 0017

Replace servo amplifier.

An error occurred in the Replace servo amplifier. amplifier's internal A/D converter. An error occurred in the amplifier's internal LSI. An error occurred in the communication between the servo amplifier and detector. A ground fault of the output was detected when the power was turned ON. Replace servo amplifier. Connect correctly. Replace or repair cable. Repair the ground fault section. Replace the cable or motor.

0018 0020

0024

Ground fault detection

(3) S03 AUX SERVO ALM Alarm information 0010 0030 Undervoltage Details The power voltage is 160V or less. Remedy Review the power supply. Replace the servo amplifier.

Regeneration error The tolerable regeneration power Set the parameter #002 correctly. of the internal regenerative Connect correctly. resistor or external regenerative Lower the positioning frequency. option was exceeded. Change the regenerative option to a larger capacity. Lower the load. Review the power supply. Regenerative transistor error Replace the servo amplifier. Increase the acceleration/ deceleration time constant. Review the gear ratio. Replace the detector. Repair the wiring. Replace the servo amplifier. Take countermeasures against noise.

0031

Overspeed

The motor's rotation speed exceeded the tolerable momentary speed. A current exceeding the servo amplifier's tolerable current flowed.

0032

Overcurrent

I - 42

1. 1.9

LIST OF ALARMS AUXILIARY AXIS ALARMS

Alarm information 0033 Overvoltage

Details The voltage of the converter in the servo amplifier was 400V or more.

Remedy Wire correctly. Replace the servo amplifier. For the internal regenerative resistor, replace the amplifier. For the external regenerative option, replace the regenerative option.

0046 0050

Motor overheating An operation state causing the motor to overheat continued. Overload 1 The servo amplifier or servomotor overload protection function activated.

Reduce the motor load. Review the operation pattern. Reduce the motor load. Review the operation pattern. Change to a motor or amplifier with large output. Change the setting of the automatic tuning response characteristics. Correct the connection. Replace the servomotor.

0051

Overload 2

The max. output current flowed for several seconds due to a machine collision or overload.

Review the operation pattern. Change the setting of the automatic tuning response characteristics. Correct the connection. Replace the servomotor.

0052

Excessive error

A position deflection exceeding the excessive error detection setting value occurred.

Increase the acceleration/ deceleration time constant. Increase the torque limit value. Review the power facility capacity. Review the operation pattern. Replace the servomotor. Connect correctly. Repair or replace the cable.

I - 43

1. 1.9

LIST OF ALARMS AUXILIARY AXIS ALARMS

(4) S52 AUX SERVO WRN Alarm information 0092 Battery voltage drop Details The absolute position detection battery voltage dropped. Remedy Mount a battery. Replace the battery and initialize the absolute position.

00E0

Lower the positioning frequency. Over-regeneration The regeneration power may warning have exceeded the tolerable Change the regenerative option range of the built-in regenerative to a larger one. resistor or external regenerative Lower the load. option. Overload warning Absolute position counter warning The overload alarm 1 could occur. There is an error in the absolute position detector internal data. Refer to the items for S03 0050. Take countermeasures against noise. Replace the servomotor.

00E1 00E3

00E9

Main circuit OFF warning

Turn ON the main circuit power. The servo ON signal was input while the main circuit power was OFF. The contactor operation is faulty.

(5) Z70 AUX POS. ERR Alarm information 0001 Details Zero point initialization incomplete Absolute position data lost Absolute position system related parameter error Cause The zero point (reference point) has not been initialized in the absolute position system. Remedy Initialize the zero point (reference point).

0002

The absolute position coordinate Initialize the zero point (reference point). data in the amplifier has been lost. The absolute position system related parameters have been changed or lost. Correctly set the parameters and then initialize the zero point (reference point).

0003

(6) Z71 AUX DETEC. ERR Alarm information 0001 Details Absolute position memory battery voltage drop Cause Remedy

The data in the detector has been Check the battery and detector cable and then initialize the zero lost. point (reference point). Battery voltage drop. Detector cable wire breakage or looseness.

I - 44

1. 1.9

LIST OF ALARMS AUXILIARY AXIS ALARMS

(7) Z73 AUX SYSTEM WRN Alarm information 0001 Details Absolute position memory battery voltage warning Absolute position counter warning Cause Battery voltage drop. Detector cable wire breakage or looseness. An error occurred in the detector's absolute position counter. Remedy Check the battery and detector cable. The zero point does not need to be initialized. Replace the detector.

0003

(8) M00 AUX OPER. ALM Alarm information 0001 Details Near-point dog length insufficient Cause Remedy

Lower the zero point return speed When executing dog-type or increase the dog length. reference point, the zero point return speed is too fast or the dog length is too short. When executing reference point Move the axis in the correct return, the axis was moved in the direction. opposite of the designated direction. The axis interlock function is valid. An interlock was established by the servo OFF function. The soft limit was reached. Cancel the interlock signal Cancel the servo OFF. Check the soft limit setting and machine position Initialize the absolute position reference point and then fix the absolute position coordinates. Initialize the absolute position reference point and then fix the absolute position coordinates.

0003

Reference point return direction illegal External interlock Internal interlock Soft limit

0004 0005 0007 0024

Reference point return was In absolute executed during an absolute position alarm. position alarm. Reference point return not possible. Reference point return was In initializing absolute position. executed while initializing the absolute position. Reference point return not possible.

0025

I - 45

1. 1.9

LIST OF ALARMS AUXILIARY AXIS ALARMS

(9) M01 AUX OPER. ALM Alarm information 0001 Details Cause Remedy Correctly designate the operation mode.

No operation mode The operation mode is not designated, or the operation mode was changed during axis movement. Feedrate 0 The operation parameter's feedrate setting is zero. The operation parameter feedrate setting is zero. Or, the override is valid, and the override value is zero.

0003

Set a value other than zero in the feedrate setting or override value.

0060

A station No. exceeding the No. Station No. designation illegal. of indexed divisions was designated. Starting not possible. Reference point return incomplete. Starting not possible. In initializing reference point. Starting not possible. In absolute position alarm. Starting not possible. In random positioning mode. Manual operation not possible. Uneven indexing station No. illegal. Starting not possible.

Correctly designate the station No.

0061

Automatic/manual operation was Execute the reference point return. started before reference point return was executed with the incremental system. The start signal was input while initializing the absolute position reference point. Complete the absolute position reference point initialization.

0062

0063

The start signal was input during Initialize the absolute position an absolute position alarm. reference point and then fix the absolute position coordinates. The manual operation mode was Turn the random positioning mode OFF before switching to started during the random the manual operation mode. positioning mode. The commanded station No. was Check the commanded station No. higher than 8 during uneven indexing.

0064

0065

I - 46

1. 1.9

LIST OF ALARMS AUXILIARY AXIS ALARMS

AUXILIARY AXIS MCP ALARMS Y02 AUX SYSTEM ALM Error No. 0050 An error occurred in the data transmitted between the MCP and auxiliary axis amplifier after the power was turned ON. Details Background error Remedy The software or hardware may be damaged. Contact the service center. A communication error has occurred between the controller and amplifier. Take measures against noise. Check that the communication cable connector between the controller and amplifier and one between the amplifiers are tight. Check whether the communication cable between the controller and amplifier and one between the amplifiers are disconnected. A driving amplifier may be faulty. Take a note of the 7-segment LED contents of each driving amplifier and report to the Service Center.

0051

0000 0001 0002 03

CRC error (10 times/910.2ms) CRC error (2 continuous times) Reception timing error (2 continuous times) Data ID error (2 continuous times) : Axis No. No. of reception frames error (2 continuous times) : Axis No.

04

Y03 AUX AMP UNEQU. The amplifier is not correctly connected.

Check the auxiliary axis amplifier mounting state. Check the end of the cable wiring. Check the cable for broken wires. Check the connector insertion. The auxiliary axis amplifier input power is not being input. The auxiliary axis amplifier axis No. switch is illegal.

Error No. Axis No.1 to 4

Details bit correspondence (bit 0 : 1st axis, bit 1: 2nd axis, bit 2: 3rd axis, bit 3: 4th axis)

I - 47

1. 1.10

LIST OF ALARMS COMPUTER LINK ERRORS

1.10 COMPUTER LINK ERRORS

Error Message L01 DNC ERROR Error No. 4 Details
Communication ends with timeout.

Remedy

10

15

16 17

1) Set a greater timeout value in the input/output device parameter. CNC has a 248-byte receive buffer. 2) Recheck the HOST software as to The time during which CNC receives whether or not the HOST transmits data in response to DC1 from CNC 248 bytes exceeds the TIME-OUT (data request). value set in the I/O device parameter. 3) Check whether or not start code of computer link parameter is set to 0. HOST ER (CNC DR) signal is not turned 1) Check whether or not the cable is ON. disconnected from the connector. 2) Check whether or not the cable is broken. 3) Check whether or not the HOST power is turned ON. Communication ends with parity H. 1) Recheck the HOST software as to whether or not the data to be transmitted to CNC is ISO code. Communication ends with parity V. 1) Recheck the data to be transmitted to CNC. Although CNC transmits DC3 (request to 1) Recheck the software as to whether or not the HOST stops transmitting data stop data transfer) to the HOST, it within 10 bytes after receiving DC3. receives data of 10 bytes or more from 2) Recheck the HOST software as to the HOST, thus terminates whether or not the HOST transmits communication. data such as a command or header to When CNC is transmitting data to the CNC during receiving a work program. HOST, it receives data of 10 bytes or more from the HOST.

I - 48

1. 1.11

LIST OF ALARMS USER PLC ALARMS

1.11 USER PLC ALARMS

Message U01 No PLC Sub-status 1 2 Details The ladder is not a GPPW ladder or PLC4B ladder. (Note) Emergency stop (EMG) will be applied. Remedy Download the ladder of the format selected with the PLC environment selection parameters (bit selection #51/bit 4).

U10 Illegal PLC

0x0010 0x0040

Scan time error Edit the ladder size to a The scan time is 1 second or longer. smaller size. Ladder operation mode illegal A ladder different from the designated mode was downloaded. (Note) Emergency stop (EMG) will be applied. GPPW ladder code error (Note) Emergency stop (EMG) will be applied. PLC4B ladder code error An illegal circuit was found in the PLC4B ladder. bit1: PC medium-speed circuit illegal bit2: PC high-speed circuit illegal (Note) Emergency stop (EMG) will be applied. Download the ladder having the same format as when the power was reset or turned ON. Download the correct GPPW format ladder. Download the correct PLC4B format ladder.

0x0080

0x008x

0x0400

Number of Software illegal interrupt ladder steps The ladder process stopped abnormally due to an illegal software command code. (Note) Emergency stop (EMG) will be applied.

Turn the power ON again. If the error is not reset, download the correct ladder.

0x800x

Software exceptional interrupt Number of ladder steps The ladder process stopped abnormally due to a bus error, etc. bit 0: BIN command operation error Refer to the methods for bit 1: BCD command operation error using the BCD and BIN function commands. bit6: CALL/CALLS/RET command error bit7: IRET command execution error (Note) Emergency stop (EMG) is applied for bit 6/7. Turn the power ON again. If the error is not reset, download the correct ladder. Start the ladder.

U50 Stop PLC

The ladder is stopped.

(Note) The number of ladder steps displayed on the screen may not match the actual number of error occurrence steps because of the ladder timing. Use this as a guideline of the occurrence place.

I - 49

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.1 OPERATION ERRORS

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT

If a setting operation error occurs on any setting and display unit screen the error No. EOO and a message describing the details of the error will display in the line above the data setting area or the menu display area.

2.1 OPERATION ERRORS

: Message requiring resetting and restarting : Message requiring restarting after canceling error conditions (The bold characters are the messages displayed on the screen.) Error No. E01 Error message SETTING ERROR Details The setting data is incorrect. An alphabetic character was set when only number can be set etc. Data was input without setting number (#). (Word editing) Even though no retrieval data was set, menu key [ ] or [ ] was pressed. Even though no data is stored in edit buffers, menu key Replace was pressed. One of the following characters was entered as the first character of the retrieval data and edit buffers: 0 to 9, . , (space), +, , =, *, [ ] , and " " . When the incremental detection system was used, the parameter (#0 absolute position setting) was set on the absolute position setting screen. The data input for the standard parameter setting or during execution of formatting is not Y or N. A value from 4 to 10 was specified for #1043 lang. Even though no language data exists, its output and comparison were attempted. Check the numbers (0253 and 0254) of the language data to be output. When the machine manufacturer macro program memory area is the SRAM area, the setup parameter #1060 SETUP was set to 20. When the machine manufacturer macro program memory area is the SRAM area, writing of the machine manufacturer macro program was attempted on PROGRAM COPY screen.

I - 50

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.1 OPERATION ERRORS

Error No. E02

Error message DATA OVER

Details The setting data exceeded the setting range. The compensation data specification exceeded the range when inputting the tool offset data on tape so that block could not be input. Press the INPUT key again while the input screen is displayed and the input will continue from the next block. When workpiece coordinate offsets are measured, the calculation results given by pressing the CALC key are exceeding the specified range. Correctly specify the tool length or the wear data of cutting edges used for the calculation. When there was no option, 2 or more was specified for #1043 lang. Otherwise, an option was added and 23 or more was specified for #1043 lang. The corresponding setting No. (#) was not found. This error occurs if a setting No. not found on the screen was set and input or if a variable No. not found in the specifications was set and input for the common variables. When the tool length was measured manually, a nonexisting tool wear compensation number was specified and the sensor was turned ON. Specify the R register of the offset number correctly. The input/output unit power is not ON. The cable is disconnected. Setting of the transfer speed (baud rate) does not agree.

E03

No. NOT FOUND

E04

DEV. NOT READY

I - 51

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.1 OPERATION ERRORS

Error No. E05

Error message NOT ACCEPTABLE

Details The PLC timer cannot be set from the screen when the program is valid. (When machine parameter bit selection #6449 bit 1 is set to 1.) The PLC counter cannot be set from the screen when the program is valid. (When machine parameter bit selection #6449 bit 0 is set to 1.) The tool registration data setting is prohibited. (When special relay E71 is valid by the PLC.) Setting from the tool life management screen is prohibited. Absolute position setting screens #1 ORIGIN and #2 ZERO cannot be set when #0 INIT SET is invalid. The total of axes set in #1001 SYS_ON #1002 axisno is illegal. Set so that the total No. of axes is within the specifications range for the target model. #1037 cmdtyp is not within the setting range. The INPUT key was pressed to perform search for the program that is in background edit status on the word edit screen. The menu keys (Replace and Insert) on the word edit screen were manipulated when a running program is displayed (PDISP signal: ON). An attempt was made to set MDI data in an MDI setting lock state (the MDI setting lock parameter is specified with 0 and a non-MDI mode is valid). Language data in display selection status was entered. Change the display selection status once before entering the data. (#1043 lang) When the manual value command protection (#1228 aux12/bit7) function is valid, the first monitor screen was manipulated by manual command operation (M, S, and T keys). The menu key for a function not in the specifications was pressed. A parameter not in the specifications was set. A language that was not added as an option was selected. (#1043 lang) Set up parameter #1049 mmac_R was set to 1 when the machine manufacturer macro option was not valid. Set up parameter #1060 SETUP was set to 20 when the machine manufacturer macro option was not valid. Writing of the machine manufacturer macro program with the PROGRAM COPY screen was attempted when the machine manufacturer macro option was not valid.

E06

NO SPEC

I - 52

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.1 OPERATION ERRORS

Error No. E07 E08 E09

Error message RESET END PHYSICAL ERR TIME OUT

Details The input/output operations were forcibly stopped by reset etc. (including EMG). The input/output parameter setting or input/output unit side setting was incorrect. The input/output unit parameter #9116 TIME-OUT SET setting was too short. There is no EOB code in the machining program. The program cannot be written because the memory capacity is exceeded. This error occurs when the MDI data setting on the MDI screen exceeds 500 characters or when saving MDl editing or making a program on the edit screen input on the data input/output screen program copy etc. When registering a machining program in the memory a program with the same No. as the designated program No. was found in the memory. Refer to the program file to find a program No. not being used and reset the program No. A program with the same No. as the machining program to be copied from the memory was found in the IC card. This error occurs during MDI registration in the MDI screen or during creation of a program in the edit screen. When registering a machining program in the memory the No. of programs determined in the specifications is exceeded preventing registration. This error occurs during MDI registration in the MDI screen creation of a program in the edit screen data input in the data input/output screen and program copy. The block with the designated sequence No. or block No. does not exist in the designated program. The designated program is not found in the memory. The corresponding program No. was not found with search of tape memory during graphic check. An operation (edit input/output buffer correction etc.) inhibited for machining program B was attempted. An operation (edit input/output buffer correction etc.) inhibited for machining program C was attempted. A parity H error was detected during data input etc. Check the paper tape or input device. This error may occur if the paper tape is dirtied with oil etc. A parity V error was detected during data input. Check the paper tape to see whether the number of characters in the significant information section of a block is odd. Also check the state (cable wiring noise measures etc.) of the connected equipment.

E10

MEMORY OVER

E11

PROG. No. DUPLI

E12

FILE ENTRY OVER

E13 E14

NB NOT FOUND PROG. NOT FOUND EDIT LOCK B EDIT LOCK C PARITY H ERR

E15 E16 E17

E18

PARITY V ERR

I - 53

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.1 OPERATION ERRORS

Error No. E20

Error message OVER RUN ERR

Details The control method using the DC codes etc. for the input/output operation is incorrect. Check the settings of the input/output unit parameters and the settings on the input/output unit side and reset if necessary. Deletion of a machining program was attempted during operation. Search was attempted during operation. Change of data such as parameters was attempted during operation. Start of graphic check was attempted during operation. When using the two systems, the program being buffer corrected was running with the other system. Erasing or inputting (IC NC) of a program in the IC card being used was attempted. Formatting of the IC card was attempted during automatic start. Accessing to the host computer was attempted during automatic operation. There was an illegal code on the paper tape. Data input/output or comparison was attempted when the PLC was not stopped. Analog output adjustment was attempted when the PLC was not stopped. An attempt was made to input or output language data during PLC execution. When the machine manufacturer macro program memory area was set to the FROM area, formatting of the FROM area (#1060 SETUP 20) was attempted when the PLC was not stopped, writing of the machine manufacturer macro program was attempted on the PROGRAM COPY screen, or input of the macro program was attempted. (Measures) Stop the PLC. Set the control unit rotary switch to 1. Set the onboard file screen RUN/STOP setting to 1. When inputting the tool offset data onto tape an offset type exceeding the specifications range was designated and that block could not be input. If the INPUT key is pressed again in the input screen the input will continue from the next block. The designated character string was not found from the block displayed on the screen to the end of the program when searching with data search in the edit screen. Press the INPUT key again and the search will start at the head of the program. An inconsistency was found in the paper tape and memory data during comparison. Continuous or step graphic check was not possible because the operation mode was illegal.

E21

PROGRAM RUNNING

E22 E24

CODE CHANGE ERR PLC RUN

E25

DATA MEMORY ERR

E26

NO CHARACTERS

E35 E40

COMPARE ERROR OP MODE ERROR

I - 54

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.1 OPERATION ERRORS

Error No. E50 E51 E52 E53 E54 E55 E56 E60

Error message FILE ERR FILE OPEN ERR FILE CLOSE ERR FILE SEEK ERR FILE READ ERR FILE DELETE ERR FILE INSERT ERR

Details If one of these errors occurs the editing or input/output operations cannot be continued. Contact the Service Center. As for E50 a classification No. will display at the end of the message. Inform the service center of this No. as well.

IOP ERR

A classification number is displayed after the message for E60. Refer to the section shown in parentheses and remedy the problem. E60 lOP ERROR 2 (Port already being used) E60 lOP ERROR 4 (E09 TIME OUT) E60 lOP ERROR 5 (E08 PHYSICAL ERR) E60 lOP ERROR 7 (E07 RESET END) E60 lOP ERROR 10 (E04 DEV. NOT READY) E60 lOP ERROR 15 (E17 PARITY H ERR) E60 lOP ERROR 16 (E18 PARITY V ERR) E60 lOP ERROR 17 (E20 OVER RUN ERR) E60 lOP ERROR 18 (E22 CODE CHANGE ERR) E60 IOP ERROR 20 (framing and H/W errors) Setting for the bit length is incorrect. (Baud rate, stop bit, and character length) Check the setting of the I/O device system and its parameters and set it again. Check the situations of the connected devices (cable wiring and noise measures). Data was input/output or the tape search was executed during the host link. Set 0 in #8109 HOST LINK, and then set 1 again before performing the cycle start. (IOP error -2) The host link parameter was turned ON during connecting to the Anshin-net. Turn the Anshin-net valid OFF. (IOP error -2) When #10812 Anshin-net/ Machine builders network system valid is set to 1, the modem connection port of the Anshin-net or machine builders network system is occupied. Perform inputting or outputting using a port other than the modem connection port. (IOP error -2) When connecting the GX Developer (when the bit selection parameter #6451 bit5 is set to 1), the port 2 of the RS232C communication port is always used. Use a port other than the port 2 of the RS232C communication port. (IOP error -2)

I - 55

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.1 OPERATION ERRORS

Error No. E62

Error message I/O PARAM ERR

Details The EIA code data set for I/O parameter is of an unusable code. The unusable codes are those used as the EIA standard codes and the even hole codes. The same No. as the program No. designated for program copy was found in the memory. During tape input the first character of the machining program block is the program No. address O or L. During tape input the same No. as the specified program was found in the memory. During tape input the program No. was not found on the paper tape and a program No. was not designated on the screens data setting area. Set the program No. and input again. Search (operation search) was attempted during program check (continuous or step). Retry search after the program check is completed or after resetting the program search A tool No. already registered was newly registered on the tool life management screen. Registration of data exceeding the max. No. of registerable tools was attempted on the tool life management screen. When inputting the tool offset data onto tape a compensation number exceeding the specifications range was specified and that block could not be input. If the INPUT key is pressed again in the input screen the input will continue from the next block. The coordinate value of the hole center cannot be obtained. Reset the measurement point, which must not applied to the following conditions. The measurement A point is the same as the Y coordinate of the C point. The measurement B is the same as the Y coordinate of the C point. The slope of the line through A and C point is the same as the slope of the line through B and C point. Press the operation menu = Input or + input during the tool measurement. Press the operation menu = Input or + input during the manual value command mode. Press the screen selection menu on which is displayed during the tool measurement. Press the screen selection menu on which is displayed during the manual value command mode.

E64

PROGRAM No. ERR

E65 E66

PROG. No. DUPLl NO PROG. NUMBER PROG. CHECK MODE

E69

E70 E71

TOOL No. DUPLl TOOL ENTRY OVER

E73

CANT CALCULATE

E74

MENU IMPOSSIBLE

I - 56

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.1 OPERATION ERRORS

Error No. E75

Error message TLM ILL. SIGNAL

Details The sensor signal was already ON when the tool measurement mode (TLM) signal was validated. After the tool measurement mode (TLM) signal was validated, the sensor signal turned ON when there was no axis movement. The sensor signal turned ON at a position within 100m from the final entry start position. Turn the tool measurement mode signal input OFF, or turn the sensor signal OFF and move the axis in a safe direction. Note) This display will be erased when another screen is opened. The display will not be erased even if the tool measurement mode signal input is turned OFF, or if the axis is moved in a direction away from the sensor. The offset No. to be used for workpiece coordinate system offset data measurement was invalid. Restart from tool selection. (Correctly specify the R register that contains the offset number.) Zero point return has not been completed for the axis being measured. Return the axis to the zero point. During movement of two or more axes the sensor turned ON and the tool length was measured. Keep off from the sensor and perform the measurement for one axis at a time. The sensor turned on for an axis that has not completed dog-type reference point return and the tool length was measured. Return the axis to the zero point. The program head search (unmodal type search) was not executed before type 2 (standard specification) restart search was executed for program restart. Set the type to unmodal, search for the head of the program, and then search for the restart block with type 2. After completing the type 1 or type 2 search for program restart, the unmodal type, type 1 or type 2 search was attempted again. If program restart is continued (if the axis is return to the restart position with automatic or manual operations), the program will restart from the block searched for first. To search again, cancel the previous search by resetting, and then search again. An attempt was made to input a parameter in the setup parameter locked state. Refer to the manual issued by the machine manufacturer. The parameter #1925 EtherNet of the high-speed program server function is set to 0. When writing data to the IC card, the file name is illegal. (Exceeding 8 characters of file name + 3 characters of extension.)

E76

TOOL No. ERROR

E77 E78

AXIS No. REF-RET AX UNMATCH (TLM)

E79

NO REF-RTN (TLM) TOP SEARCH ERR

E80

E82

ALREADY RESEARCH

E84

CANT IN/OUT

I - 57

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.1 OPERATION ERRORS

Error No. E86

Error message INPUT DATA ERR

Details When inputting the tool offset data the data format was not correct so that block could not be input. If the INPUT key is pressed again in the input screen the input will continue from the next block. When data is read from parameter tape, its format is incorrect. The format of file written to the NC memory is illegal. Playback edit was executed for a fixed cycle subprogram. Playback edit of a fixed cycle subprogram is not possible. Playback edit cannot be executed unless the block being edited with playback is displayed to the end (EOB) on the left side of the machining program display area. Press the cursor key and display the whole block to the end. Then input the data. G90 was set when PB_G90 was OFF. G91 was set when PB_G90 was ON. When restarting the program, the type 3 restart search was attempted with a program containing no T command. Check the program. When restarting the program, the T command corresponding to the type 3 restart search was not found in the program. Check the program. When restarting a program for 2-systems, restart search was performed simultaneously for the 1st and 2nd systems, and then the 2nd system was searched again. If program restart is continued (if the axis is return to the restart position with automatic or manual operations), the program will restart from the block searched for first. To search again, cancel the previous search by resetting, and then search again. When carrying our program restart, type 3 restart search was attempted while the machine was at the negative () side of the restart limit parameters. Manually move the machine to the positive (+) side of the restart limit parameters, and search again. The keys other than Function/Menu/Previous page/Next page were pressed in Auxiliary monitor screen during auxiliary axis operation. An attempt was made to perform background search for the program that is in foreground search status. (Word editing) Operation search was attempted in tape mode. The hardware status cant be read correctly so automatic adjustment was not possible. Check the remote l/O unit. A Z55 RIO NOT CONNECT occurred. Adjust manually. Unit defect (replace unit)

E87 E88

NOT EDIT PROG. CANT ADD BLOCK

E91 E98

MODE ERROR (PBK) CANT RESEARCH

E165

AUX RUNNING

E190 E191 E200

FORE EDITING NOT COM. SEARCH ADJUST ERROR

I - 58

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.1 OPERATION ERRORS

Error No. E201

Error message UNIT NOT EQUIP

Details The analog output unit is not mounted. Confirm the remote l/O unit. Prepare a unit having analog output. Check the connection (power and signal wires) Unit defect (replace unit) A socket connection attempt failed during Ethernet communication. Check the host address, the setting of the port No. and that the host computer is turned ON. A login attempt failed during Ethernet communication. Check the user name and password. Check the account settings, such as the home directory. Transmission of a file with Ethernet communication ended because of timeout. An attempt to read a host file failed during Ethernet communication. An attempt to write to a host file failed during Ethernet communication.

E301

CONNECT ERROR

E302

LOGIN ERR

E303 E311 E312 E313

TIME OUT DOWNLOAD ERR UPLOAD ERR NO FILE

The file specified by host receive (host IC) operation during Ethernet communication is not found in the host. The file specified by host send (IC host) operation during Ethernet communication is not found in the IC card. The file name specified to be stored by host receive (host IC) operation during Ethernet communication already exists in the IC card. The file name specified to be loaded by host send (IC host) operation during Ethernet communication already exists in the host. An attempt to write to the IC card failed during Ethernet communication. An attempt to read a file from the IC card failed during Ethernet communication. IC card memory is full. NC memory is full. A host directory contains too many files. An attempt to move a directory failed. In the IC card device, accessing a directory in the nineteenth layer or more was attempted. When backup or writing of the expansion cassette into/from the FROM, the expansion cassette (HR437) was not mounted in CBUS#1 or was incorrectly mounted. When backup or writing of the expansion cassette into/from the FROM, a card other than the expansion cassette (HR437) was mounted in CBUS#1. When the program memory was formatted to 1280m or more, the expansion cassette (HR437) was not mounted in CBUS#1.

E314

FILE DUPLICATE

E315 E316 E317 E318 E319

FILE WRITE ERR FILE READ ERR MEMORY OVER OVER FLOW ERR DIRECTORY ERR

E320

HR437 UNEQU

I - 59

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.2 OPERATION MESSAGES

2.2 OPERATOR MESSAGES

The following messages indicate the status of the setting and display functions and are not operation errors. They are mainly used to show that operation is normal and serve as guides for the following operations. There is no classification by numbers. 2.2.1 SEARCH AND OPERATION RELATED

Message SEARCH EXECUTION SEARCH COMPLET BUFFER EDIT

Message details Search is being executed normally. Search was completed normally. The buffer is being corrected. This appears when the cursor or a tab key is pressed and the buffer correction mode is entered. This is erased when INPUT is pressed. When using 2 systems, the program being buffer corrected is being used by the other system. Buffer correcting of a machine manufacturer macro program was attempted. Buffer correcting is prohibited since the data protection key 3 is valid.

CANT BUF. EDIT

DATA PROTECTING

I - 60

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.2 OPERATION MESSAGES

2.2.2 MDI/EDITING RELATED

Message MDI NO SETTING MDI SETTING COMPLETE MDI ENTRY COMPLETE

Message details Only display of MDI data (no execution) The MDI data setting has been completed (execution is now possible). The MDI data was saved in the memory with the specified program No. The NC is operating with an MDI program and the MDI data cannot be corrected. Status in which no programs to be edited have been called on the editing screen. To edit press the SEARCH or PROGRAM edit key. The details of a program are being edited on the screen. Press INPUT to write the data in the memory. A machining program to be edited is currently being run with memory operation and cannot be edited. Waiting for a key entry (whether to delete the program) in word edit status (when the background search menu is selected) Background edit mode Editing can be performed in foreground edit mode. Editing cannot be performed in foreground edit mode. This state also occurs during feed hold or fixed cycle mode (single-block stop). The word matching the search data was searched on word editing.

MDI RUNNING

PUSH KEY SERCH/PROG

EDITING

PROGRAM RUNNING

DELETE? (Y/N)

BACK GROUND EDITING EDIT POSSIBLE EDIT IMPOSSIBLE

WORD SEARCH FIN

I - 61

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.2 OPERATION MESSAGES

2.2.3 DATA INPUT/OUTPUT RELATED

Message DATA IN EXECUTION DATA WRITING IN PROGRESS

Message details Data is being read without error from the paper tape. Data has been entered normally and the input data is being written to the ROM. Data has been stored without error. Comparison is being executed without error. Comparison has completed without error. Data is being output without error. Data has been output without error. Data is being erased without error. Data has been erased without error. The machining program is being copied without error. The machining program has been copied without error. The machining program is being condensed without error. The machining program has been condensed without error. The machining program is being merged without error. The machining program has been merged without error. The machining program No. is being changed without error. The machining program No. has been changed without error.

DATA IN COMPLETE COMPARE EXECUTION COMPARE COMPLETE DATA OUT EXECUTION DATA OUT COMPLETE ERASE EXECUTION ERASE COMPLETE COPY EXECUTION COPY COMPLETE CONDENSE EXECUTION CONDENSE COMPLETE MERGE EXECUTION MERGE COMPLETE No. CHANGE EXECUTION No. CHANGE COMPLETE

I - 62

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.2 OPERATION MESSAGES

2.2.4 S-ANALOG OUTPUT ADJUSTMENT RELATED

Message ADJUST EXECUTION ADJUST COMPLETE

Message details Analog output adjustment is being executed without error. Analog output adjustment has completed without error.

2.2.5 AUXILIARY AXIS

Message CONTINUE Y/N BACKUP EXECUTION BACKUP COMPLETE

Message details Type Y or N to specify whether to perform operation. The auxiliary axis parameters are being backed up in SRAM. The backup of the auxiliary axis parameters in SRAM has been completed. The auxiliary axis parameters in SRAM is being written to MR-J2-CT. The writing of the auxiliary axis parameters in SRAM to MR-J2-CT has been completed. The absolute position in SRAM has been restored in MR-J2-CT.

AUX. WRITING EXEC. WRITE COMPLETE

ABS POS RESTORED

2.2.6 PARAMETER BACKUP RELATED

Message BACKUP EXEC. Y/N BACKUP EXECUTION BACKUP COMPLTE RESTORE EXEC. Y/N RESTORE EXECUTION RESTORE COMPLETE

Message details Type Y or N to specify whether to perform the operation. The parameters are being backed up. Backup of the parameters has been completed. Type Y or N to specify whether to perform the operation. The parameters are being restored. Restoration of the parameters has been completed.

I - 63

2.

OPERATION MESSAGES ON SETTING AND DISPLAY UNIT 2.2 OPERATION MESSAGES

2.2.7 OTHERS

Message DATA PROTECTING

Message details The data protection key is valid and the various data cannot be set or erased etc. Waiting for the key input of standard parameter setting (Y/N). The standard parameters are being set. Waiting for the key input of execute format (Y/N). Formatting is being executed. The simple setup has been completed. Setup with #1060 SETUP "1" has been completed. Formatting with #1060 SETUP "20" has been completed. Completed without executing simple setup. (When N has been set for both BASE PARA. SET? (Y/N) and EXECUTE FORMAT? (Y/N).) Confirmation for erasing operating time or alarm history. Waiting for the key input of tool length data by manual measurement. Waveform display data cannot be output while waveform is displayed. The system is waiting for a key input to indicate whether to write the macro programs into the FROM. The macro program is being written into the FROM. The macro program has been written into the FROM.

BASE PARA. SET? (Y/N) BASE PARA EXECUTION EXECUTE FORMAT? (Y/N) FORMAT EXECUTION SETUP COMPLETE

NON SETUP

CONFIRM OPE? (Y/N) INPUT? (Y/N) V-ANALIZER EXEC. ROM WRITE? (Y/N) DATA WRITING WRITE COMPLETE

I - 64

3.

PROGRAM ERROR

3.

PROGRAM ERROR
(The bold characters are the message displayed in the screen.) These alarms occur during automatic operation and the causes of these alarms are mainly program errors which occur for instance when mistakes have been made in the preparation of the machining programs or when programs which conform to the specification have not been prepared. Error No. P 10 Details EXCS. AXIS No. The number of axis addresses commanded in the same block exceeds the specifications. AXIS ADR. ERROR The axis address commanded by the program and the axis address set by the parameter do not match. DIVISION ERROR An axis command which cannot be divided by the command unit has been issued. NOT ACCEPT CMND The normal line control command (G40.1, G41.1, G42.1) has been issued during the modal in which the normal line control is not acceptable. PARITY H The number of holes per character on the paper tape is even for EIA code and odd for ISO code. PARITY V The number of characters per block on the paper tape is odd. ADDRESS ERROR An address not listed in the specifications has been used. FORMAT ERROR The command format in the program is not correct. G-CODE ERROR A G code not listed in the specifications has been used. G51.2 or G50.2 was commanded when the rotary tool axis No. (#1501 polyax) was set to 0. G51.2 or G50.2 was commanded when the tool axis was set to the linear axis (#1017 rot 0). Remedy Divide the alarm block command into two. Check the specifications.

P 11

Revise the axis names in the program.

P 20

Check the program.

P 29

Check the program.

P 30

Check the paper tape. Check the tape puncher and tape reader.

P 31

P 32

P 33

Make the number of characters per block on the paper tape even. Set the parameter parity V selection OFF. Check and revise the program address. Check and correct the parameters values. Check the specifications. Check the program.

P 34

Check and correct the G code address in the program. Check the parameter setting values.

I - 65

3.

PROGRAM ERROR

Error No. P 35

Details

Remedy

P 36

P 37

P 39

P 40

P 60

P 62

P 65 P 70

Check the program. CMD-VALUE OVER The setting range for the addresses has been exceeded. Enter the M02 and M30 command at the end PROGRAM END ERR of the program. EOR has been read during tape and Enter the M99 command at the end of the memory operation. subprogram. The program numbers are designated across PROG. NO. ZERO a range from 1 to 99999999. A zero has been specified for program The sequence numbers are designated and sequence numbers. across a range from 1 to 99999. Check the specifications. NO SPEC ERR A non-specified G code was specified. The high-speed program server operation specifications are not provided. Reconsider the program. PREREAD BL. ERR When tool radius compensation is executed there is an error in the pre-read block and so the interference check is disabled. Reconsider the axis address command. OVER CMP. LENG. The commanded movement distance is excessive. (Over 231) The default movement modal command at F-CMD. NOTHING power ON is G01. This causes the machine No feed rate command has been issued. to move without a G01 command if a There is no F command in the cylindrical movement command is issued in the interpolation or pole coordinate program, and an alarm results. Use an F interpolation immediately after the G95 command to specify the feedrate. mode is commanded. Specify F with a thread lead command. Check the high-speed mode III NO G05P3 SPEC specifications. Check the numerical values of the addresses ARC ERROR that specify the start and end points, arc There is an error in the arc start and end center as well as the radius in the program. points as well as in the arc center. Check the + and directions of the The difference of the involute curve through the start point and the end point is address numerical values. large.

I - 66

3.

PROGRAM ERROR

Error No. P 71

Details

Remedy

P 72

P 90

P 93

P100

P111

P112

P113

Check the numerical values of the addresses ARC CENTER in the program. The arc center is not sought during Check whether the start point or end point is R-specified circular interpolation. The curvature center of the involute curve on the inner side of the base circle for involute interpolation. When carrying out tool cannot be obtained. radius compensation, check that the start point and end point after compensation are not on the inner side of the base circle for involute interpolation. Check whether the start point and end point are at an even distance from the center of the base circle for involute interpolation. Check the helical specifications. NO HELICAL SPEC An Axis 3 command was issued by the A helical command has been issued circular interpolation command. If there is no though it is not included in the helical specification, the linear axis is moved specifications. to the next block. Check the specifications. NO THREAD SPEC A thread cutting command has been issued though it is not included in the specifications. Issue the thread cutting command and then SCREW PITCH ERR set the screw pitch command properly. The screw pitch has not been set correctly when the thread cutting command is issued. Check the specifications. NO CYLIND SPEC Cylindrical interpolation was commanded when the cylindrical interpolation specifications were not provided. Before issuing the plane selection PLANE CHG (CR) commands, issue G68 and then G69 Plane selection commands (G17, G18, and G19) were issued when a coordinate (coordinate rotation cancel). rotation command (G68) was issued. Issue the plane selection command after the PLANE CHG (CC) A plane selection command (G17 G18 tool radius compensation command or nose R compensation command has been G19) has been issued when the tool canceled (issue axial movement command radius compensation command (G41 after the G40 cancel command). G42) or nose R compensation command (G41 G42 G46) is issued. The plane selection command was issued when nose R compensation is completed there is no axial movement command after the G40 command and the compensation has not been canceled. Issue arc command on the correctly selected ILLEGAL PLANE plane. The arc command axis is not on the selected plane.

I - 67

3.

PROGRAM ERROR

Error No. P122

Details NO AUTO C-OVR An automatic corner override command (G62) has been issued though it is not included in the specifications. 2nd AUX. ADDR The 2nd miscellaneous function address specified in the program does not match that set by the parameter. NO G96 SPEC (No constant peripheral speed) The constant peripheral speed command (G96) was issued despite the fact that such a command does not exist in the specifications. SPINDLE S = 0 No spindle speed command has been specified. G96 P-No. ERR An invalid constant peripheral speed control axis has been specified. NO C-CMP SPEC Even though there were no tool radius compensation specifications, tool radius compensation commands (G41 and G42) were issued. Even though there were no nose R compensation specifications, nose R compensation commands (G41, G42, and G46) were issued. G2 3 CMP. ERR A compensation command (G40 G41 G42 G43 G44 G46) has been issued in the arc mode (G02 G03).

Remedy Check the specifications. Delete the G62 command from the program.

P130

Check and correct the 2nd miscellaneous function address in the program.

P131

Check the specifications. Change from the constant peripheral speed command (G96) to the rotation speed command (G97).

P132

Reconsider the program.

P133

Reconsider the parameter specified for the constant peripheral speed control axis. Check the specifications.

P150

P151

P152

P153

I.S.P NOTHING In interference block processing during execution of a tool radius compensation (G41 or G42) or nose R compensation (G41 G42 or G46) command the intersection point after one block is skipped cannot be determined. Reconsider the program. I.F ERROR An interference error has arisen while the tool radius compensation command (G41 G42) or nose R compensation command (G41 G42 G46) was being executed.

Issue the linear command (G01) or rapid traverse command (G00) in the compensation command block or cancel block. (Set the modal to linear interpolation.) Reconsider the program.

I - 68

3.

PROGRAM ERROR

Error No. P155

Details

Remedy

P156

P157

P158

P170

P172

P173

P177

The radius compensation mode is F-CYC ERR (CC) established when a fixed cycle command is A fixed cycle command has been issued executed and so the radius compensation in the radius compensation mode. cancel command (G40) should be issued. Change the vector to that with which the BOUND DIRECT At the start of G46 nose R compensation compensation direction is defined. the compensation direction is undefined Exchange with a tool having a different tip point number. if this shift vector is used. Change the G command to that which allows SIDE REVERSED inversion of the compensation direction (G00 During G46 nose R compensation the G28 G30 G33 or G53). compensation direction is inverted. Exchange with a tool having a different tip point number. Turn ON the #8106 G46 inversion error avoidance parameter. Change the tip point number to a legal one. ILLEGAL TIP P. During G46 nose R compensation the tip point is illegal (other than 1 to 8). Add the compensation number command to NO CORR. No. the compensation command block. The compensation number (DOO TOO Check the number of compensation number HOO) command was not given when the sets a correct it to a compensation number radius compensation (G41 G42 G43 command within the permitted number of G46) command was issued. compensation sets. Alternatively the compensation number is larger than the number of sets in the specifications. Check the address L-Number of the G10 G10 L-No. ERR command and correct the number. (G10 L-number error) The L address command is not correct when the G10 command is issued. First check the number of compensation sets G10 P-No. ERR and then set the address P designation to (G10 compensation error) within the permitted number of sets. When the G10 command is issued a compensation number outside the permitted number of sets in the specifications has been commanded for the compensation number command. The tool life management data cannot be LIFE COUNT ACT Registration of tool life management data registered when counting the used data. Turn the used data count valid signal OFF. with G10 was attempted when the used data count valid signal was ON.

I - 69

3.

PROGRAM ERROR

Error No. P178

Details LIFE DATA OVER The No. of registration groups total No. of registered tools or the No. of registrations per group exceeded the specifications range.

Remedy Review the No. of registrations. The maximum No. of registrations is shown below.
System No. of groups No. of tools Per group System 1 80 80 16 System 2 40/40 40/40

P179

P180

P181

P182

P183

P184

P190

GROUP No. ILL. When registering the tool life management data with G10 the group No. was commanded in duplicate. A group No. that was not registered was designated during the T 99 command. An M code command must be issued as a single command but coexists in the same block as that of another M code command. The M code commands set in the same group exist in the same block. NO BORING CYC. A fixed cycle command was issued though there are not fixed cycle (G72 G89) specifications. NO S-CMD (TAP) The spindle rotation speed command has not been issued when the hole drilling fixed cycle command is given. SYN TAP ERROR Connection to the main spindle unit was not established. PTC/THD No. The pitch or thread number command has not been issued in the tap cycle of a hole drilling fixed cycle command. NO PTC/THD CMD The pitch or the number of threads per inch is illegal in the tap cycle of the hole drilling fixed cycle command. NO CUTTING CYC A lathe cutting cycle command was input although the lathe cutting cycle was undefined in the specification.

The group No. cannot be commanded in duplicate. When registering the group data register it in group units. Correct to the correct group No.

Check the specifications. Correct the program.

Issue the spindle rotation speed command (S) when the hole drilling fixed cycle command G84 G74 (G84 G88) is given. Check connection to the main spindle. Check that the main spindle encoder exists. Specify the pitch data and the number of threads by F or E command.

Check the pitch or the number of threads per inch.

Check the specification. Delete the lathe cutting cycle command.

I - 70

3.

PROGRAM ERROR

Error No. P191

Details TAPER LENG ERR In the lathe cutting cycle the specified length of taper section is illegal. CHAMFERING ERR Chamfering in the thread cutting cycle is illegal. NO MRC CYC SPC The fixed cycle for compound lathe I (G70 to G73) was commanded when the fixed cycle for compound lathe I specifications were not provided. PROG. ERR (MRC) When called with a fixed cycle for compound lathe I command, the subprogram contained at least one of the following commands: Reference point return command (G27, G28, G29, G30) Thread cutting (G33, G34) Fixed cycle skip-function (G31) The first move block of the finish shape program in fixed cycle for compound lathe I contains an arc command. BLOCK OVR (MRC) The number of blocks in the shape program of the fixed cycle for compound lathe I is over 50 or 200 (this differs according to the model). CONF. ERR (MRC) The fixed cycle for compound lathe I (G70 to G73) shape program could not cut the work normally because it defined an abnormal shape. VALUE ERR (MRC) A command value of the fixed cycle for compound lathe (G70 to G76) is illegal. NO PAT CYC SPC A fixed cycle for compound lathe II (G74 to G76) command was input although it was undefined in the specification. NO SPECIAL CYC No special fixed cycle specifications are available. NO HOLE (S_CYC) A 0 has been specified for the number of holes in special fixed cycle mode.

Remedy The radius set value in the lathe cycle command must be smaller than the axis shift amount. Set a chamfering amount not exceeding the cycle. Check the specification.

P192

P200

P201

Delete the following G codes from this subprogram that is called with the fixed cycle for compound lathe I commands (G70 to G73): G27 G28 G29, G30 G31 G33 G34, fixed cycle G-code. Remove G2 and G3 from the first move block of the finish shape program in fixed cycle for compound lathe I.

P202

P203

Specify 50 or a less value. The number of blocks in the shape program called by the fixed cycle for compound lathe I commands (G70 to G73) must be decreased below 50 or 200 (this differs according to the model). Check the fixed cycle for compound lathe I (G70 to G73) shape program.

P204

Check the fixed cycle for compound lathe (G70 to G76) command value. Check the specification.

P210

P220

Check the specifications.

P221

Reconsider the program.

I - 71

3.

PROGRAM ERROR

Error No. P222

Details G36 ANGLE ERR A G36 command specifies 0 for angle intervals. G12 G13 R ERR The radius value specified with a G12 or G13 command is below the compensation amount. NO G12 G13 SPC There are no circular cutting specifications. NESTING OVER A subprogram has been called 4 or more times in succession from the subprogram. The program in the IC card contains the M198 command. The program in the IC card has been called more than once (the program in the IC card can be called only once at a time). NO N-NUMBER At subprogram call time the sequence number set at return from the subprogram or specified by GOTO was not set. NO PROGRAM No. The subprogram has not been found when the subprogram is called. NO VARl NUMBER The variable number commanded is higher than the numbers in the specifications. EQL. SYM. MSSG. The = sign has not been commanded when a variable is defined. VARIABLE ERR. An invalid variable has been specified in the left or right side of an operation expression. NO COOD-RT SPC Even though there were no coordinate rotation specifications, a coordinate rotation command was issued. NO MACRO SPEC A macro specification was commanded though there are no such command specifications.

Remedy Reconsider the program.

P223

Reconsider the program.

P224

Check the specifications.

P230

Check the number of subprogram calls and correct the program so that it does not exceed 4 times. When using the IC card, the IC card and the number of IC card program calls.

P231

Specify the sequence numbers in the call block of the subprogram. When using an IC card, check the program and its No. in the IC card. Enter the subprogram. Check the program number in the IC card. Check the specifications. Check the program variable number.

P232

P241

P242

Designate the = sign in the variable definition of the program. Correct the program.

P243

P260

Check the specifications.

P270

Check the specifications.

I - 72

3.

PROGRAM ERROR

Error No. P271

Details NO MACRO INT. A macro interrupt command has been issued though it is not included in the specifications. MACRO ILL. A statement and a macro statement exist together in the same block. MACRO OVERCALL The number of macro call nests exceeded the specifications. MACRO ARG. EX. The number of macro call argument type II sets has exceeded the limit. CALL CANCEL A G67 command was issued though it was not during the G66 command modal. MACRO ALM MESG An alarm command has been issued in #3000. EXC. [ The number of parentheses [ or ] which can be commanded in a single block has exceeded five. [ ] ILLEGAL The number of [ and ] parentheses commanded in a single block does not match. CALC. IMPOSS. The arithmetic formula is incorrect. DIVIDE BY ZERO The denominator of the division is zero. IF SNT. ERROR There is an error in the IF conditional GOTO statement. WHILE SNT. ERR There is an error in the WHILE conditional DO -END statement. SETVN SNT. ERR There is an error in the SETVN statement when the variable name setting was made.

Remedy Check the specifications.

P272

P273

P275

Reconsider the program and place the executable statement and macro statement in separate blocks. Reconsider the program and correct it so that the macro calls do not exceed the limit imposed by the specification. Reconsider the program.

P276

P277

P280

Reconsider the program. The G67 command is the call cancel command and so the G66 command must be designated first before it is issued. Refer to the operator messages on the DIAG screen. Refer to the instruction manual issued by the machine manufacturer. Reconsider the program and correct it so the number of [ or ] does not exceed five.

P281

Reconsider the program and correct it so that [ and ] parentheses are paired up properly. Reconsider the program and correct the formula. Reconsider the program and correct it so that the denominator for division in the formula is not zero. Reconsider the program.

P282 P283

P290

P291

Reconsider the program.

P292

Reconsider the program. The number of characters in the variable name of the SETVN statement must be 7 or less.

I - 73

3.

PROGRAM ERROR

Error No. P293

Details

Remedy

P294

P295

P296

P297

P298

P300

P301

P360

P370

P371

Reconsider the program and correct it so that DO-END EXCESS the number of s in the DO END statement The number of s for DO-END in the does not exceed 27. WHILE conditional DO END statement has exceed 27. Reconsider the program and correct it so that DO-END MMC. the DOs and ENDs are paired off properly. The DOs and ENDs are not paired off properly. During tape operation a program which WHILE/GOTO TPE There is a WHILE or GOTO statement on includes a WHILE or GOTO statement cannot be executed and so the memory the tape during tape operation. operation mode is established instead. Review the program. NO ADR (MACRO) A required address has not been specified in the user macro. Review the program. ADR-A ERR. The user macro does not use address A as a variable. Review the program. PTR OP (MACRO) User macro G200 G201 or G202 was specified during tape or MDI operation. Reconsider the variable names in the VER. NAME ERROR program and correct them. The variable names have not been commanded properly. Correct the program so that the name is not VAR NAME DUPLI duplicated. The name of the variable has been duplicated. Check the specifications. NO PROG.MIRR. A mirror image (G50.1 or G51.1) command has been issued though the programmable mirror image specifications are not provided. Check the specifications. NO OPOS MR SPC The facing turret mirror image specifications are not provided. Check the program. MIRR ILLEGAL Check the parameters. Facing turret mirror image was commanded to an axis for which external mirror image or parameter mirror image is valid. Facing turret mirror image validating mirror image for a rotary axis was commanded.

I - 74

3.

PROGRAM ERROR

Error No. P380

Details NO CORNER R/C A command was issued for corner chamfering/corner rounding though there are no such specifications. NO ARC R/C SPC Corner chamfering/corner rounding was specified in the arc interpolation block although corner chamfering/corner rounding II is unsupported. CORNER NO MOVE The block next to corner chamfering/ corner rounding is not a movement command. CORNER SHORT In the corner chamfering/corner rounding command the movement distance was shorter than the value in the corner chamfering/corner rounding command. CORNER SHORT When the corner chamfering/corner rounding command was input the movement distance in the following block was shorter than the length of the corner chamfering/corner rounding. G0 G33 IN CONR A block with corner chamfering/corner rounding was given during G00 or G33 modal. NO GEOMETRIC A geometric command was issued though there are no geometric specifications. NO GEOMETRIC 2 There are no geometric IB specifications. LES AGL (GEOMT) The angular difference between the geometric line and line is 1 or less. INC ERR (GEOMT) The second geometric block was specified by an incremental value. NO G01 (GEOMT) The second geometric block contains no linear command. NO ADRS (GEOMT) The geometric format is invalid.

Remedy Check the specifications. Remove the corner chamfering/corner rounding command from the program. Check the specifications.

P381

P382

Replace the block succeeding the corner chamfering/corner rounding command by G01 command. Make the corner chamfering/corner rounding less than the movement distance since this distance is shorter than the corner chamfering/ corner rounding. Make the corner chamfering/corner rounding less than the movement distance since this distance in the following block is shorter than the corner chamfering/corner rounding.

P383

P384

P385

Recheck the program.

P390

Check the specifications.

P391 P392

Check the specifications. Correct the geometric angle.

P393

Specify this block by an absolute value.

P394

Specify the G01 command.

P395

Recheck the program.

I - 75

3.

PROGRAM ERROR

Error No. P396

Details PL CHG. (GEOMT) A plane switching command was executed during geometric command processing. ARC ERR (GEOMT) In geometric IB the circular arc end point does not contact or cross the next block start point. NO GEOMETRIC 1B Although the geometric IB specifications are not included a geometric command is given. PRAM. IN ERROR The specified parameter number or set data is illegal. An illegal G command address was input in parameter input mode. A parameter input command was input during fixed cycle modal or nose R compensation. AXIS NOT RET. A command was issued to move an axis which has not returned to the reference point away from that reference point. A command was issued to an axis removal axis. NO 2nd REF. SPC A command for second third or fourth reference point return was issued though there are no such command specifications. COLLATION ERR One of the axes did not return to the start position when the origin point collate command (G27) was executed. G27/M ERROR An M command was issued simultaneously in the G27 command block. G29/M ERROR An M command was issued simultaneously in the G29 command block.

Remedy Execute the plane switching command before geometric command processing.

P397

Recheck the geometric circular arc command and the preceding and following commands.

P398

Check the specifications.

P421

Check the program.

P430

Execute reference point return manually. The command was issued to an axis for which axis removal is validated so invalidate axis removal.

P431

Check the specifications.

P434

Check the program.

P435

P436

An M code command cannot be issued in a G27 command block and so the G27 command and M code command must be placed in separate blocks. An M code command cannot be issued in a G29 command block and so the G29 command and M code command must be placed in separate blocks.

I - 76

3.

PROGRAM ERROR

Error No. P438

Details NOT USE (G52) A local coordinate system command was issued during execution of the G54.1 command. NO CHUCK BARR. The chuck barrier on command (G22) was specified although the chuck barrier was undefined in the specification. TAPE I/O ERROR An error has arisen in the tape reader or alternatively in the printer during macro printing. FILE I/O ERROR A file of the machining program cannot be read.

Remedy Review the program.

P450

Check the specification.

P460

Check the power and cable of the connected devices. Check the I/O device parameters. In memory mode, the programs stored in memory may have been destroyed. Output all of the programs and tool data once and format them. Ensure that the external device (including a floppy disk drive and IC card) that contains the file is mounted. L01 DNC ERROR is displayed simultaneously, so remedy the problem according to the error No. Check the specification.

P461

P462

P480

P481

DNC ERROR A communication error occurred during the BTR operation. NO MILL SPEC Milling was commanded when the milling specifications were not provided. Pole coordinate interpolation was commanded when the pole coordinate interpolation specifications were not provided. Check the program. MILL ILL. G An illegal G code was used during the milling mode. An illegal G code was used during cylindrical interpolation or pole coordinate interpolation. The G07.1 command was issued during the tool radius compensation.

I - 77

3.

PROGRAM ERROR

Error No. P482

Details

Remedy

P484

Check the machining program, parameters MILL ILL. AXIS and PLC I/F signal. A rotary axis was commanded during the milling mode. Milling was executed even though an illegal value was set for the milling axis No. Cylindrical interpolation or pole coordinate interpolation was commanded during mirror image. Cylindrical interpolation or pole coordinate interpolation was commanded before the tool compensation was completed after the T command. G07.1 was commanded when cylindrical interpolation was not possible (there is no rotary axis, or external mirror image is ON). An axis other than a cylindrical coordinate system axis was commanded during cylindrical interpolation. Carry out manual reference point return. MILL AXIS RET. Movement was commanded to an axis that had not completed reference point return during the milling mode. Movement was commanded to an axis that had not completed reference point return during cylindrical interpolation or pole coordinate interpolation.

I - 78

3.

PROGRAM ERROR

Error No. P485

Details MILL ILL. MODAL The milling mode was turned ON during nose R compensation or constant surface speed control. A T command was issued during the milling mode. The mode was switched from milling to cutting during tool compensation. Cylindrical interpolation or pole coordinate interpolation was commanded during the constant surface speed control mode (G96). The command unacceptable in the cylindrical interpolation was issued. A T command was issued during the cylindrical interpolation or pole coordinate interpolation mode. A movement command was issued when the plane was not selected just before or after the G07.1 command. A plane selection command was issued during the pole coordinate interpolation mode. Cylindrical interpolation or pole coordinate interpolation was commanded during tool radius compensation. The G16 plane in which the radius value of a cylinder is 0 was specified. MILLING ERROR The milling command was issued during the mirror image (when parameter or external input is turned ON). Pole coordinate interpolation, cylindrical interpolation or milling interpolation was commanded during facing turret mirror image. The start command of the cylindrical interpolation or polar coordinate interpolation was issued during the normal line control. SYNC CODE ERR Two or more synchronization M codes were commanded in the same block. The synchronization M code and "!" code were commanded in the same block.

Remedy Check the program. Before issuing G12.1, issue G40 or G97. Before issuing G12.1, issue a T command. Before issuing G13.1, issue G40. Specify the radius value of a cylinder other than 0, or specify the X axiss current value other than 0 before issuing G12.1/G16.

P486

Check the program.

P511

Check the program.

I - 79

3.

PROGRAM ERROR

Error No. P600

Details NO AUTO TLM. An automatic tool length measurement command (G37) was execute though there are no such command specifications. NO SKIP SPEC. A skip command (G31) was issued though there are no such command specifications. NO MULTI SKIP A multiple skipping command (G31.1 G31.2 or G31.3) was issued though there are no such command specifications. SKIP SPEED 0 The skip speed is 0. TLM ILL. AXIS No axis or more than one axis was specified in the automatic tool length measurement block. T-CMD IN BLOCK The T code is in the same block as the automatic tool length measurement block. NO T-CMD BEFOR The T code was not yet specified in automatic tool length measurement. TLM ILL. SIGNL Before the area specified by the D command or decelerating area parameter d the measurement position arrival signal went ON. The signal remains OFF to the end. SKIP ERROR (CC) A skip command was specified during radius compensation processing. ILLEGAL PARA. The parameter setting is not correct. G114.1 was commanded when the spindle synchronization with PLC I/F command was selected. G113 was commanded when the spindle-spindle polygon machining option was OFF and the spindle synchronization with PLC I/F command was selected.

Remedy Check the specifications.

P601

Check the specifications.

P602

Check the specifications.

P603 P604

Specify the skip speed. Specify only one axis.

P605

Specify this T code before the block.

P606

Specify this T code before the block.

P607

Check the program.

P608

Specify a radius compensation cancel (G40) command or remove the skip command. Check whether #1549 Iv0vR1 to #1553 Iv0vR5 are set in descending order (in order of large values). Check whether #1554 Iv0rd2 to #1557 Iv0rd5 are set in descending order. Check and correct #1514 expLinax and #1515 expRotax. Check the program. Check the parameter.

P610

I - 80

3.

PROGRAM ERROR

Error No. P612

Details EXP. ERROR A movement command for exponential function interpolation was issued during facing turret mirror image. CMD-VALUE ILL. Spindle synchronization was commanded to a spindle that is not connected serially. NO TANZ. SPEC A normal line control command (G40.1, G41.1, G42.1) was issued when the normal line control specifications were not provided. TAN. AXIS G92 A coordinate system preset command (G92) was issued to a normal line control axis during normal line control. TAN. AXIS LINE The normal line control axis was set to a linear axis. The normal line control axis was set to the linear type rotary axis II axis. The normal line control axis has not been set. The normal line control axis was the same as the plane selection axis. PLANE CHG (TAN) The plane selection command (G17, G18, G19) was issued during normal line control. PREPRO S/W ERR Combining commands that required pre-reading (nose R offset corner chamfering/corner rounding geometric I geometric IB and fixed cycle for compound lathe) resulted in eight or more pre-read blocks.

Remedy Check the program.

P700

Check the program. Check the parameter.

P900

Check the specifications.

P901

Check the program.

P902

Correct the normal line control axis.

P903

Delete the plane selection command (G17, G18, G19) from the program for normal line control. Reduce the number of commands that require pre-reading or delete such commands.

P990

I - 81

II

EXPLANATION OF PARAMETERS

1. 1.1

SCREEN CONFIGURATION SCREEN TRANSITION CHARTS

1.

SCREEN CONFIGURATION

1.1 SCREEN TRANSITION CHARTS

When the function selection key MENU is pressed the following menu appears: TOOL menu is displayed after the power is turned on. To display PARAM menu use menu key on the TOOL screen.

Tool offset menu display (No.1 to 4) Setup parameter menu display (No.1 to 4)

OFFSET WORK

REGIST PROCESS I/O PAR

LIFE SETUP

MENU MENU

Previous page Key

Next page key Menu selection key

PARAM menu No.1 to 4

WORK

PROCESS #8001 to #8018 Machining parameter #8019 to #8059 Machining parameter #8071 to #8086 CONTROL PARAM #8101 to #8124 AXIS PARAM #8201 to #8212 BARRIER PARAM #8300 to #8319

I/O BASE PARAM #9001 to #9014 I/O device parameter #9101 to #9130 . . .

SETUP PARAMETER

Previous page

Next page

#9501 to #9530 Link parameter #9601 to #9630

MENU

TOOL menu

The contents of TOOL menu depends on the system.

II - 1

1. 1.1

SCREEN CONFIGURATION SCREEN TRANSITION CHARTS

Press the menu key SETUP to display the setup selection screen. If the setup parameter menu opening option is specified in this screen, the setup parameters can be set up and displayed.
Parameter menu display (No.1 to 4) Tool offset menu display (No.1 to 4) Setup parameter menu display (No.5 to 8) Setup parameter menu display (No.1 to 4) Base

Work Offset MC-ERR PLC Axis

Process Registration Macro Servo

I/O PAR

Setup Life

MENU MENU

PSW Spindle

MENU MENU

Previous page key Basic specification parameter #1001 to #1024 . . . #1925 to #1936
Previous page Next page

Menu selection key Axis specification parameter #2001 to #2012

Axis specification parameter

Next page key

Setup parameter menu No.1 to 4

Servo specification parameter Servo adjustment parameter Servo parameter #2201 to #2212 . . . #2261 to #2265

Basic specification parameter of spindle

#3001 to #3036 Spindle specification parameter Spindle specification parameter Spindle offset parameter Spindle offset parameter Spindle parameter #3201 to #3212 . . .

#2013 to #2024
Zero point return parameter

#2025 to #2036
Zero point return parameter

#2037 to #2048
Absolute position parameter

#2049 to #2060
Axis specification parameter

#2061 to #2072
Axis specification parameter

#2073 to #2084
Axis specification parameter

#2085 to #2096

#3573 to #3584

Menu switch

Machining error correction Setup parameter menu No.5 to 8 #4000 to #4047 Machining error correction #4051 to #4097 Machining offset data #4101 to #4184 . . . #5109 to #5124

PLC timer #6000 to #6055 . . .

Macro list M macro #7001 to #7103 G macro #7201 to #7313 ASCII macro #7401 to #7415

Position switch #7501 to #7574

Previous page

#6936 to #6999 PLC counter #6200 to #6223 PLC constant #6301 to #6348 #6349 to #6396 Bit selection #6401 to #6460 . . . #6581 to #6596

Next page

II - 2

2. 2.1

MACHINING PARAMETERS PROCESS PARAMETERS

2.

MACHINING PARAMETERS

2.1 PROCESS PARAMETERS

<WRK COUNT> (No. of workpieces machined) # Item 8001 WRK COUNT M Contents Setup range (unit) Set the M code that counts the No. of workpiece 0 to 99 repeated machining. The No. will not be counted when set to 0. The current machining No. is displayed. Set the 0 to 999999 initial value. Set the maximum No. of workpieces machined. 0 to 999999 A signal is output to PLC when the No. of machining times is counted to this limit.

8002 WRK COUNT 8003 WRK LIMIT

<AUTO TLM> (Automatic tool length measurement) # Item 8004 SPEED 8005 ZONE r 8006 ZONE d Contents Setup range (unit) Set the feedrate during automatic tool length 1 to 60000 (mm/min) measurement. Set the distance between the measurement position 0 to 99999.999 (mm) and deceleration start point. Set the tolerable zone of the measurement position. 0 to 99999.999 (mm) If the sensor signal turns ON in front of d before the measurement position or if the signal does not turn ON after d is passed an alarm will occur.

<AUTO CORNER OVR> (Automatic corner override) # Item 8007 OVERRIDE 8008 MAX ANGLE Contents Setup range (unit) Set the override value for automatic corner override. 0 to 100 (%) Set the max. corner opening angle where 0 to 180 () deceleration should start automatically. If the angle is larger than this value deceleration will not start. Set the position where deceleration starts at the 0 to 99999.999 (mm) corner. Designate at which length point before the corner deceleration should start.

8009 DSC. ZONE

<T-TIP OFFSET> (Wear data input) # Item 8010 ABS. MAX. (For L system only) 8011 INC. MAX. (For L system only) Contents Set the max. value when inputting the tool wear compensation amount. A value exceeding this setting value cannot be set. Set the max. value for when inputting the tool wear compensation amount in the addition mode. Setup range (unit) 0 to 99.999 (mm)

0 to 99.999 (mm)

II - 3

2. 2.1

MACHINING PARAMETERS PROCESS PARAMETERS

<FIXED C.> (Fixed cycle) # Item 8012 G73 n (For M system only) 8013 G83 n 8014 CDZ-VALE (For L system only) 8015 CDZ-ANGLE (For L system only) 8016 G71 MINIMUM (For L system only) Contents Set the return amount for G73 (step cycle). Set the return amount for G83 (deep hole drilling cycle). Set the screw cut up amount for G76 G78 (thread cutting cycle). Set the screw cut up angle for G76 G78 (thread cutting cycle). Set the minimum cut amount for the final cutting in G71 G72 (rough cutting cycle). If the final cutting amount is smaller than this value the final cut will not be performed. Set the change amount to the command cut amount D for G71 G72 (rough cutting cycle). Each cut amount will be the value obtained by adding or subtracting this value from command D and thus the amount can be changed each cut. Set up return length m at a G84/G74 pecking tap cycle. Note: Set 0 to specify a usual tap cycle. Setup range (unit) 0 to 99999.999 (mm) 0 to 99999.999 (mm) 0 to 127 (0.1 lead) 0 to 89 () 0 to 99.999 (mm)

8017

DELTA-D (For L system only)

0 to 99.999 (mm)

8018 G84/G74 return (For M system only)

0 to 999.999 (mm)

II - 4

2. 2.1 <PRECISION> (High precision control) # Item 8019 R COMP

MACHINING PARAMETERS PROCESS PARAMETERS

8020 DCC ANGLE

Contents Setup range (unit) Set up a compensation factor for reducing a control 0 to 99 (%) error in the reduction of a corner roundness and arch radius. Indicates a maximum control error (mm) in parentheses. The larger the setup value, the smaller the theoretical error will be. However, since the speed at the corner goes down, the cycle time is extended. Coefficient = 100 setting value Note: This is valid when #8021 COMP CHANGE is set to 0. Set up the minimum value of an angle (external 0 to 30 (degrees) angle) that should be assumed to be a corner. 0: The angle will be When an inter-block angle (external angle) in 5. high-precision mode is larger than the set value, it is determined as a corner and the speed goes down to sharpen the edge.

If the set value is smaller than , the speed goes down to optimize the corner.

8021 COMP CHANGE

8022 CORNER COMP

8023 CURVE COMP

8024 EDGE ANGLE

Note: If 0 is set, it will be handled as 5 degrees. The standard setting value is 0. Select whether to share or separate the compensation coefficient at the corner/curve during the high-accuracy control mode. 0: Share (#8019 R COMP) 1: Separate Corner (#8022 CORNER COMP) Curve (#8023 CURVE COMP) Set the compensation coefficient to further reduce the roundness at the corner during the high-accuracy control mode. Coefficient = 100 setting value Note: This is valid when #8021 COMP CHANGE is set to 1. Set the compensation coefficient to further reduce the radius reduction amount at the curve (arc, involute, spline) during the high-accuracy control mode. Coefficient = 100 setting value Note: This is valid when #8021 COMP CHANGE is set to 1. Not used.

0/1

1000 to 99 (%)

1000 to 99 (%)

II - 5

2. 2.1 <PRECISION> (High precision control) # Item 8025 SPLINE ON (for M system only) 8026 CANCEL ANG. (for M system only)

MACHINING PARAMETERS PROCESS PARAMETERS

8027 Toler-1 (for M system only)

8028 Toler-2 (for M system only)

8029 FairingL (for M system only) 8030 MINUTE LENGTH (for M system only)

8033 Fairing ON (for M system only) 8034 AccClamp ON (for M system only)

8035 AccClampMag 8036 CordecJudge (for M system only)

8037 CorJudgeL (for M system only)

Contents Specify whether to enable the fine spline function. 0: Disable the fine spline function. 1: Enable the fine spline function. When the angle made by blocks exceeds the set value, spline interpolation is canceled temporarily. In consideration of the pick feed, set a value a little smaller than the pick feed angle. Specify the maximum chord error in a block that includes an inflection point. Set the tolerance applicable when the applicable block is developed to fine segments by CAM. (normally about 10 m) When 0.000 is set, the applicable block is linear. Specify the maximum chord error in a block that includes no inflection point. Set the tolerance applicable when the applicable block is developed to fine segments by CAM. (normally about 10 m) When 0.000 is set, the applicable block is linear. Set the length of the block subject to fairing. (Valid when #8033 Fairing ON is set to 1.) When the length of one block exceeds the set value, spline interpolation is canceled temporarily and linear interpolation is performed. Set a value a little smaller than linear block length of the workpiece to be machined. If - 1 is set, spline interpolation is performed regardless of block length. Set whether to use the fairing function. 0: Fairing invalid 1: Fairing valid Set the method for clamping the cutting speed. 0: Clamp with parameter #2002 clamp or the corner deceleration function. 1: Clamp the cutting speed with acceleration judgment. (Valid when #8033 Fairing ON is set to 1.) Not used. Change the conditions for judging a corner. 0: Judge the corner from the angle of the neighboring block. 1: Judge the corner from the angle of the neighboring block, excluding minute blocks. (Valid when #8033 Fairing ON is set to 1.) Set the length of the block to be excluded. (Valid when #8036 CordecJudge is set to 1.)

Setup range (unit) 0/1

0 to 180 0: 180

At 1m 0.000 to 100.000mm At 0.1m 0.0000 to 10.0000mm At 1m 0.000 to 100.000mm At 0.1m 0.0000 to 10.0000mm 0 to 100.000mm 1 to 127mm 0: 1mm

0/1

0/1

0/1

0 to 99999.999 (mm)

II - 6

2. 2.1 <C axis normal line> # Item 8041 C-rot.R

MACHINING PARAMETERS PROCESS PARAMETERS

8042 C-ins.R

Contents Setup range (unit) This is valid with normal line control type II. 0.000 to 99999.999 Set the length from the center of the normal line (mm) control axis to the end of the tool. This is used to calculate the turning speed at the block joint. This is valid with normal line control type I. 0.000 to 99999.999 Set the radius of the arc to be automatically inserted (mm) into the corner during normal line control.

<Fixed cycle> # 8051 G71 8052 8053 G73 8054 8055 8056 G74 8057 G76 8058 Item THICK PULL UP U W R RETRACT LAST-D TIMES Contents Set the amount of cut-in by the rough cutting cycle (G71, G72) Set the amount of recess after cutting by the rough cutting cycle (G71, G72). Set the X-axis cutting margin of the forming rough cutting cycle (G73). Set the Z-axis cutting margin of the forming rough cutting cycle (G73). Set the number of times cutting is performed by the forming rough cutting cycle (G73). Set the amount of retract (amount of cut-up) of the push-cut cycle (G74, G75). Set the amount of final cut-in by the composite threading cycle (G76). Set the number of times the amount of final cut-in (G76 finish margin) is divided in the composite threading cycle (G76). Set the angle (thread angle) of the tool nose in the composite threading cycle (G76). Setup range (unit) 0 to 99999.999 (mm) 0 to 99999.999 (mm) 99999.999 to 99999.999 (mm) 99999.999 to 99999.999 (mm) 0 to 99999 (times) 0 to 99.999 (mm) 0 to 99.999 (mm) 0 to 99 (times)

8059

ANGLE

0 to 99 ()

<Three-dimensional cutter compensation> # Item 8071 3-D CMP (for M system only) Contents Setup range (unit) Value of p in the following denominator constants for 0 to 99999.999 three-dimensional tool radius compensation Vx = i x r/p, Vy = j x r/p, Vz = k x r/p Vx, Vy, Vz: X, Y, and Z axes or vectors of horizontal axes i, j, k: Program command value r: Offset p=

i 2 + j 2 + k 2 when the set value is 0.

II - 7

2. 2.1 < Scale factor> # Item 8072 SCALING P (for M system only)

MACHINING PARAMETERS PROCESS PARAMETERS

Contents Setup range (unit) Set the scale factor for reduction or magnification for 0 to 99.999999 the machining program for which the G50 or G51 command is issued. This parameter is effective when the program specifies no scale factor.

<Tool ID> # Item 8073 OfsetPosition (for M system only) Contents Setup range (unit) Set the tool offset memory number position for 0 to 999 writing the tool information data's tool length offset amount, tool radius compensation amount, tool length wear amount and tool radius wear amount into the tool offset data. Note: If 0 or a value exceeding the number of tool compensation sets is set, the data will not be written into the tool offset data. Set the head position when writing the tool 0 to 999 information data's user areas 4 to 9 in the macro variables.

8074 IDMacroTop (for M system only)

<Spiral interpolation> # Item 8075 SpiralEndErr (for M system only) Contents Setup range (unit) Designate the tolerable error range (absolute value) 0 to 99999.999 (mm) when the end point position commanded with the command format type 2 spiral interpolation or conical interpolation command differs from the end point position obtained from the speed and increment/ decrement amount. Not used.

8076 SpiralMinRad (for M system only) <Involute interpolation> # Item 8077 InvoluteErr (for M system only)

Contents Set the tolerable error value of the involute curve that passes through the start point and the involute curve that passes through the end point during involute interpolation.

Setup range (unit) 0 to 99999.999 (mm)

<Screen saver> # Item 8078 Screen Saver Contents Set the time to turn the screen OFF. The screen saver will not turn ON if 0 is set. (Note) This parameter setting is valid only for the LCD display unit. Setup range (unit) 0 to 60 (min) 0: Do not turn screen OFF.

II - 8

2. 2.1 <Deep hole drilling cycle> # Item 8083 G83S modeM (for M system only) 8084 G83S Clearanse (for M system only) 8085 G83S Forward F (for M system only) 8086 G83S Back F (for M system only)

MACHINING PARAMETERS PROCESS PARAMETERS

Contents Set the M command code for changing to the small diameter deep hole drilling cycle mode. Set the clearance amount for the G83 small diameter deep hole drilling cycle. Set the feedrate from the R point to the cutting start position in the G83 small diameter deep hole drilling cycle. Set the speed for returning from the hole base during the G83 small diameter deep hole drilling cycle.

Setup range (unit) 1 to 99999999 0 to 999.999 (mm) 0 to 99999 (mm/min)

0 to 99999 (mm/min)

II - 9

2. 2.2

MACHINING PARAMETERS CONTROL PARAMETERS

2.2 CONTROL PARAMETERS

# Item 8101 MACRO SINGLE Contents Select the control of the blocks where the user macro command continues. 0: Do not stop while macro block continues. 1: Stop every block during signal block operation. Select the interference (bite) control to the workpiece from the tool diameter during tool radius compensation and nose R compensation. 0: An alarm is output and operation stops when an interference is judged. 1: Changes the path to avoid interference. Select the interference (bite) control to the workpiece from the tool diameter during tool radius compensation and nose R compensation. 0: Performs interference check. 1: Does not perform interference check. Select the edit lock for program Nos. 8000 to 9999. 0: Program can be edited. 1: Editing of above program is prohibited. Select the control for the compensation direction reversal in G46 (nose R compensation). 0: An alarm is output and operation stops when the compensation direction is reversed (G41 G42 G42 G41). 1: An alarm does not occur when the compensation direction is reversed and the current compensation direction is maintained. 0: In arc cutting mode, the machine moves to the inside because of a delay in servo response to a command, making the arc smaller than the command value. 1: In arc cutting mode, the machine compensates the movement to the inside because of a delay in servo response to a command Specify whether to perform arc radius error correction over all axes or axis by axis. 0: Perform correction over all axes. 1: Perform correction over axis by axis. Note: This parameter is effective only when #8107 R COMPENSATION is 1. Setup range (unit) 0/1

8102 COLL. ALM OFF

0/1

8103 COLL. CHK OFF

0/1

8105 EDIT LOCK B

0/1

8106 G46 NO REV-ERR (For L system only)

0/1

8107 R COMPENSATION

0/1

8108 R COMP Select

0/1

II - 10

2. 2.2

MACHINING PARAMETERS CONTROL PARAMETERS

# Item 8109 HOST LINK

8110 G71/G72 POCKET

8111 Milling Radius

8112 DECIMAL PNT-P

8113 MillingInitG16

8114 MillingInitG19

Contents Specify whether to enable computer link B instead of the RS-232C port. 0: Disable computer link B to enable normal RS-232C communication. 1: Enable computer link B to disable normal RS-232C communication. Set the pocket machining if there is a dimple (pocket) in the rough cutting cycle (G71, G72) finishing program. 0: Pocket machining OFF 1: Pocket machining ON Select the diameter and radius of the linear axis for milling (cylindrical/pole coordinate) interpolation. 0: All axes radius command 1: Each axis setting (follows #1019 dia diameter designated axis) Note: This parameter is valid only in the milling (cylindrical/pole coordinate) interpolation mode. 0: The decimal point command for G04 address P is invalidated. 1: The decimal point command for G04 address P is validated. Designate which plane to use for milling machining after the power is turned ON or reset. #8113 #8114 Plane 0 0 G17 plane 0 1 G19 plane 1 0 G16 plane 1 1

Setup range (unit) 0/1

0/1

0/1

0/1

0: Plane other than G16 1: Select G16 plane

0: Plane other than G19 Note: This parameter is valid for the G code system 1: Select G19 plane 2, 3 (#1037 cmdtyp=3, 4).

II - 11

2. 2.3

MACHINING PARAMETERS AXIS PARAMETERS

2.3 AXIS PARAMETERS

Set up the parameter required for each axis. # Item 8201 AX. RELEASE Contents Select the function to remove the control axis from the control target. 0: Control as normal. 1: Remove from control target. Select the stored stroke limit II function set in #8204 and #8205. 0: Stored stroke limit II valid 1: Stored stroke limit II invalid When the simple absolute position method (#2049 type is 9) is selected the stored stroke limits I, II (or IIB) and IB will be invalid until the first zero point return is executed after the power is turned ON. 0: Stored stroke limit II valid (according to #8202) 1: Stored stroke limit II invalid Note: Temporary cancel of #8203 soft limit affects all the stored stroke limits. This sets the coordinates of the () direction in the moveable range of the stored stroke limit II or the lower limit coordinates of the prohibited range of stored stroke limit IIB. If the sign and value are the same as #8205, the stored stroke limit II (or IIB) will be invalid. If the stored stroke limit IIB function is selected, the prohibited range will be between two points even when #8204 and #8205 are set in reverse. When II is selected, the entire range will be prohibited. This sets the coordinates of the (+) direction in the moveable range of the stored stroke limit II or the upper limit coordinates of the prohibited range of stored stroke limit IIB. Set the coordinates of the tool change position for G30. n (tool change position return). Set with coordinates in the basic machine coordinate system. Select the shift operation at G76 (fine boring) and G87 (back boring). Specifies the shift direction at G76 and G87. Set the last positioning direction and distance for a G60 (uni-directional positioning) command. Setup range (unit) 0/1

8202 OT-CHECK OFF

0/1

8203 OT-CHECK-CANCEL

0/1

8204 OT-CHECK-N

99999.999 (mm)

8205 OT-CHECK-P

99999.999 (mm)

8206 TOOL CHG. P

99999.999 (mm)

8207 G76/87 IGNR (For M system only) 8208 G76/87 () (For M system only) 8209 G60 SHIFT (For M system only)

0: Shift effective 1: No shift 0: Shift to (+) direction 1: Shift to () direction 99999.999 (mm)

II - 12

2. 2.3

MACHINING PARAMETERS AXIS PARAMETERS

# Item 8210 OT INSIDE

8211 MIRR. IMAGE

Contents Setup range (unit) The stored stoke limit function to be set in #8204 0/1 and #8205 prevents the machine from moving to the inside or outside of the specified range. 0: Inhibits outside area (select stored stroke limit II.) 1: Inhibits inside area (select stored stroke limit II B.) Enable or disable the parameter mirror image 0/1 function. 0: Disable 1: Enable

II - 13

2.

MACHINING PARAMETERS 2.4 BARRIER DATA

2.4 BARRIER DATA

# Item 8300 PO (For L system only) Contents Setup range (unit) Set the reference X-coordinates of the chuck 99999.999 (mm) and the tail stock barrier. Set the center coordinate (Radius value) of workpiece by the basic machine coordinate system. Set the area of the chuck and tail stock barrier. 99999.999 (mm) (Radius value) Set the coordinate value from the center of workpiece for X-axis. Set the coordinate value by basic machine coordinate system for Z-axis.

P1 P2 P3 P4 P5 P6 (For L system only) 8310 Barrier ON (For L system only) 8301 8302 8303 8304 8305 8306

8311 8312

8313 8314

8315

8316

Select the validity of the chuck and tailstock barrier. 0: Invalid (Setting from special display unit valid) 1: Valid Set the area of the left spindle section. P7 P8 X axis: Set the coordinate value from the (For L system only) workpiece center (P0). (radius value) Z axis: Set the coordinates in the basic machine coordinate system. Set the area of the right spindle section. P9 P10 X axis: Set the coordinate value from the (For L system only) workpiece center (P0). (radius value) Z axis: Set the coordinates in the basic machine coordinate system. BARRIER TYPE (L) Set the shape of the left chuck and tailstock (For L system only) barrier. 0: No area 1: Chuck 2: Tailstock BARRIER TYPE (R) Set the shape of the right chuck and tailstock (For L system only) barrier. 0: No area 1: Chuck 2: Tailstock

0/1

99999.999 (mm)

99999.999 (mm)

0/1/2

0/1/2

II - 14

2.

MACHINING PARAMETERS 2.4 BARRIER DATA

# Item 8317 DELIV. AX. NAME (For L system only)

Contents When the right chuck and tailstock barrier is movable, set the name of the delivery axis. When using the 2-system method and the delivery axis is an axis in the other system, designate the system as 1A, 1B or 2A, 2B. If the system is not designated as A and B, the set system will be used. 8318 STOCK ANGLE (L) Set the angle for the left tailstock end section. (For L system only) The angle will be interpreted as 90 if there is no setting (0). 8319 STOCK ANGLE (R) Set the angle for the right tailstock end section. (For L system only) The angle will be interpreted as 90 if there is no setting (0).

Setup range (unit) A/B/.. (axis address) 1A/1B/.. 2A/2B/.. (system designation) 0 (cancel) 0 to 180 () 0: 90 default 0 to 180 ()

II - 15

2. 2.5

MACHINING PARAMETERS TOOL MEASUREMENT PARAMETERS

2.5 TOOL MEASUREMENT PARAMETERS

Set up the parameter of the tool (touch tool sensor), etc, used for measurement. # Item 8701 Tool length 8702 Tool Dia 8703 OFFSET X 8704 8705 RETURN 8706 FEED Y Contents Set the length to the end of the touch tool. Set the spherical diameter of the touch tool end. Set the spindle center deviation amount from the touch tool center in the X axis direction. Set the spindle center deviation amount from the touch tool center in the Y axis direction. Set the return distance to contact the touch tool against the workpiece again. Set the feedrate when contacting the touch tool against the workpiece again. Setup range (unit) 99999.999 (mm) 99999.999 (mm) 99999.999 (mm) 99999.999 (mm) 99999.999 (mm) 1 to 60000 (mm/min)

II - 16

3. 3.1

I/O PARAMETERS BASE PARAMETERS

3.

I/O PARAMETERS
Pressing the menu key PARA displays the I/O BASE PARAM screen. There are basically two types of input/output parameters which must be set when inputting outputting or referring to data or when performing tape operation. One type is the parameters related to the input/output device. The baud rate etc. is set according to each device. Up to five types of input/output devices can be registered. The other type of input/output parameters is the I/O base parameters which determine which device is connected to which channel per input/output application.
I/O

3.1 BASE PARAMETERS

<I/O> # <PORT No.> Specify the board No. to which the serial input/output device is connected to 2. Set 1 to use ch1. Set 2 to use ch2. # <DEV. No.> <DEV. NAME>

DATA IN

DATA OUT

TAPE MODE MACRO PRINT PLC IN/OUT REMOTE PROG IN EXT UNIT

9001 Specify the port for inputting the data such as machine program and parameters. 9003 Specify the port for outputting the data such as machine program and parameters. 9005 Specify the input port for running with the tape mode. 9007 Specify the output port for the user macro DPRINT command. 9009 Specify the port for inputting/outputting various data with PLC. 9011 Specify the port for inputting remote programs. 9013 Specify the port for communication with an external unit.

Set the input/output device No. for each application. The device Nos. are 0 to 4 and correspond to the input/output device parameters. The device name set in the input/output device parameter is also displayed for identification. 9002 Specify the No. of the device that inputs the data. 9004 Specify the No. of the device that outputs the data. 9006 Specify the No. of the device to be run with the tape mode. 9008 Specify the No. of the device for the DPRINT command. 9010 Specify the No. of the device for the PLC input/output. 9012 Specify the number of the device used to input remote programs. 9014 Specify the number of the unit used for communication with an external unit Setup range (unit) 1/2

# Item 9015 PORT NO. (tool ID)

9016 DEV. NO. (tool ID)

Contents Set the number of the port connected with the tool ID. (Either ch1 or ch2 can be used.) Set 1 to use ch1. Set 2 to use ch2. Set the number of the input/output device to be used. (Any device No. can be used.)

(M64) 0 to 4 (M64)

II - 17

3. 3.2

I/O PARAMETERS I/O DEVICE PARAMETERS

3.2 I/O DEVICE PARAMETERS

Parameters for up to five types of input/output devices can be set in DEV <0> to <4>. # Item 9101 DEVICE NAME Contents Set the device name corresponding to the device No. Set a simple name for quick identification. Setup range (unit) Use alphabet characters numerals and symbols to set a name within 3 characters. 0: 19200 (bps) 1: 9600 2: 4800 3: 2400 4: 1200 5: 600 6: 300 7: 150 1: 1 (bit) 2: 1.5 3: 2 0: Parity bit not added 1: Parity bit added 0: Odd parity 1: Even parity 0: 5 (bit) 1: 6 2: 7 3: 8 0 and 3: EOR 1 and 2: EOB or EOR 1: RTS/CTS method 2: No procedure (No handshaking) 3: DC code method 0: No parity to DC code (DC3 = 13H) 1: DC code with parity (DC3 = 93H) DC2 / DC4 0: None / None 1: Yes / None 2: None / Yes 3: Yes / Yes 0: Do not add 1: Add

9102 BAUD RATE

Set the serial communication speed.

9103 STOP BIT

Set the stop bit length used in the start-stop system.

9104 PARITY CHECK 9105 EVEN PARITY 9106 CHR. LENGTH

Specify whether to add the parity check bit to the data during communication. Specify the odd or even parity when it is added to the data. Set the length of the data bit.

9107 TERMINATOR TYPE 9108 HAND SHAKE

The code to terminate data reading can be selected. Specify the transmission control method. The method will be no procedure if a value except 1 to 3 is set. Specify the DC code when the DC code method is selected.

9109 DC CODE PARITY

9111 DC2/DC4 OUTPUT

Specify the DC code handling when outputting data to the output device.

9112 CR OUTPUT

Specify whether to insert the <CR> code just before the EOB (L/F) code during output.

II - 18

3. 3.2

I/O PARAMETERS I/O DEVICE PARAMETERS

# Item 9113 EIA OUTPUT

9114 FEED CHR. 9115 PARITY V

9116 TIME-OUT

9117 DR OFF 9118 DATA ASC II

9119 INPUT FORM

9121 EIA CODE 9122 9123 9124 9125 9126 9127 9128 9201 9301 9401 9501

[ ] # = : $ !

Contents In data output mode, select the ISO or EIA code for data output. In data input mode, the ISO and EIA codes are identified automatically. Specify the length of the tape feed to be output at the start and end of the data during tape output. Specify whether to check the parity of the No. of characters in block during data input. The No. of characters is factory-set so that the check is valid at all times. Set the time out time to detect an interruption in communication. Time out check will not be executed when set to 0 to 30 seconds. Specify whether to check the DR data at the data input/output. 0: Output in ISO/EIA code (Depends on whether #9113, #9213, #9313, #9413, or #9513 EIA output parameter is set up) 1: Output in ASC II code Specify the mode for input (collation). 0: Standard input (Data from the very first EOB is handled as significant information.) 1: EOBs following the first EOB of the input data are skipped until data other than EOB is input. When output with EIA code data can be output using the alternate code in which the special ISO code not included in EIA is specified. Specify the codes which do not duplicate the existing EIA codes by hexadecimal for respective special codes.

Setup range (unit) 0: ISO code output 1: EIA code output

0 to 999 (characters) 0: Do not perform parity V check 1: Perform parity V check 0 to 30 (s)

0: DR valid 1: DR invalid 0/1

0/1

0 to FF (hexadecimal)

Set the same settings for device 1. Set the same settings for device 2. Set the same settings for device 3. Set the same settings for device 4.

II - 19

3.3

3. I/O PARAMETERS COMPUTER LINK PARAMETERS

3.3 COMPUTER LINK PARAMETERS

# Item 9601 BAUD RATE Contents Specify the rate at which data is transferred. Setup range (unit) 0: 19200 (bps) 1: 9600 2: 4800 3: 2400 4: 1200 5: 600 6: 300 7: 110 8: 38400 Specify stop bit length used in start-stop mode. See 1: 1 PARITY EFFECTIVE in #9603. The number of 2: 1.5 characters is adjusted in output mode so that no 3: 2 problems occur if the parity check is enabled. This parameter is set when using a parity bit separately from the data bit.
ON OFF Start bit 1 character b1 b2 b3 b4 b5 b6 Data bit bn Parity bit Stop bit

9602 STOP BIT

9603 PARITY EFFECTIVE

0: No parity bit used in I/O mode 1: Parity bit used in I/O mode

9604 EVEN PARITY

9605 CHR. LENGTH 9606 HAND SHAKE

Set this to match the input/output device specifications. Specify whether even or odd parity is used when parity is used. This parameter is ignored when no parity is used. Specify data bit length. See PARITY EFFECTIVE in #9603. RS-232C transmission control mode DC control mode should be set for computer line B.

0: Odd parity 1: Even parity

9607 TIME-OUT SET

9608 DATA CODE

2: 7 3: 8 0: No control 1: RTS/CTS method 2: No handshaking 3: DC control mode Specify time-out time at which an interruption of data 0 to 999 (1/10s) transfer during data input/output should be detected. If 0 is set, time infinity is specified. Specify the code to be used. 0: ASCII code See PARITY EFFECTIVE in #9603. 1: ISO code

II - 20

3.3

3. I/O PARAMETERS COMPUTER LINK PARAMETERS

# Item 9609 LINK PARAM. 1

Contents Setup range (unit) Bit 1: DC1 output after NAK or SYN 0: Don't output the Specify whether to output the DC1 code after the DC1 code. NAK or SYN code is output. 1: Output the DC1 code. 0: Enable resetting in the computer link. 1: Disable resetting in the computer link Bit 2: Specify the control code parity (even parity for 0: No control code the control code). parity added Set the parity in accordance with the I/O device 1: Control code parity specifications. added Bit 3: Parity V Specify whether to enable checking of parity V in one block in data input mode. Not used Not used Not used Specify the code by which file data transfer begins at first. This parameter is used for a specific user, and set 0 in this parameter for normal operation. Bit 0: NAK output Specify whether to send the NAK code to the host if a communication error occurs in computer link B. 0: Disable 1: Enable Bit 7: Enable/disable resetting Specify whether to enable resetting in the computer link.

9610 LINK PARAM. 2

9611 9612 9613 9614

LINK PARAM. 3 LINK PARAM.4 LINK PARAM.5 START CODE

0: DC1 (11H) 1: BEL (07H)

9615 CTRL. CODE OUT

0: Do not output the NAK code. 1: Output the NAK code.

Bit 1: SYN output 0: Do not output the Specify whether to send the SYN code to the SYN code. host if NC resetting or an emergency stop occurs 1: Output the SYN in computer link B. code. Bit 3: DC3 output 0: Do not output the Specify whether to send the DC3 code to the host DC3 code. when communication ends in computer link B. 1: Output the DC3 code. Not used Not used Not used Not used Not used Not used Not used Not used Not used

9616 9617 9618 9619 9620 9621 9622 9623 9624

CTRL. INTERVAL WAIT TIME PACKET LENGTH BUFFER SIZE START SIZE DC1 OUT SIZE POLLING TIMER TRANS. WAIT TMR RETRY COUNTER

II - 21

4.

SETUP PARAMETERS

4.

SETUP PARAMETERS
Pressing the menu key SETUP displays the OPEN SETUP PARAM screen. The systems basic parameters are normally hidden as setup parameters to prevent mistaken operations and to simplify the display. The setup parameters can be displayed and set by making a declaration to open the setup parameters on this screen.

[OPEN SETUP PARAM]

PARAM 3

Open the menu setup parameter? *YES: Y INPUT *NO: N INPUT

#( WORK

) PROCESS I/O PAR SETUP MENU

1)

Select the setup parameter. Key-in Y in # ( ) and then press INPUT. The basic specification parameter screen appears and the normally hidden setup parameter menu will display. The required menu can be selected to display and set the setup parameters. Cancel the setup parameter selection. Key-in N in # ( ) and then press INPUT. The setup parameter menu will disappear. Note: The setup parameters are not displayed when the power is turned ON.

2)

(Note 1) Refer to 5. Base Specifications Parameters to 13. Position Switch for details on the setup parameters. (Note 2) Be sure to turn OFF the power supply after selecting the setup parameter. (Note 3) If a key other than the screen changeover key is pressed when the setup parameters are locked, the message Data Protected will appear.

II - 22

5.

BASE SPECIFICATIONS PARAMETERS

5.

BASE SPECIFICATIONS PARAMETERS

After setting up the parameter (PR) listed in the table, turn OFF the NC power. To validate the parameter, turn ON the power again. (SETUP PARAM 1. 1/15)

# Items 1001 SYS_ON System (PR) validation setup 1002 axisno Number of (PR) axes

Details Setting range (unit) Specify the existence of the 1st system 2nd system 0: Not used and PLC axis with 1 or 0. 1: Used Set No. of axes in each system and the No. of PLC axes. Specify 6 as the maximum value for each system and 4 as that for the PLC axis so that the total of those values is 6 or less. Specify the input setting value for each system and the PLC axis. The parameter units will follow this specification. Specify each axis name address with an alphabetic character. Use the characters X Y Z U V W A B or C. Do not specify the same address in one system. The same address can be specified for the 1st and 2nd system. The PLC address does not need to be set. (The axis name is displayed as 1 and 2.) When specifying the program movement rates absolute or incremental method with an address specify the incremental command axis name address with an alphabetic character. The address that can be used is the same as #1013 axname. Specify an address that is different from that #1013. Setting is not required if absolute/incremental specification with addresses is not performed (#1076 Abslnc = 0). Specify the minimum unit of the program movement amount. cunit Movement amount for movement command 1 10: 0.001 mm ( 1 m) 100: 0.01 mm ( 10 m) 1000: 0.1 mm (100 m) 10000: 1.0 mm If there is a decimal point in the movement command the decimal point position will be handled as 1mm regardless of this setting. Specify whether the machine system (ball screw pitch position detection unit) is an inch unit system or metric unit system. 0 to 6

1003 iunit (PR) 1013 axname

Input setup unit Axis name

B: 1 m C: 0.1 m Axis addresses such as X, Y, Z, U, V, W, A, B, and C

1014 incax

Increment command axis name

1015 cunit (PR)

Command unit

10 100 1000

1 m 10 m 100 m

10000 1 mm

1016 iout (PR)

Inch output

0: Metric unit system 1: Inch unit system

II - 23

5.

BASE SPECIFICATIONS PARAMETERS

# 1017 rot (PR)

Items Rotational axis

1018 ccw (PR)

Motor CCW

1019 dia (PR)

Diameter specification axis

1020 sp_ax (PR)

Spindle Interpolation

Details Specify whether the axis is a rotary axis or linear axis. For the rotary axis the position display will be 360 and the axis will return to 0. If the position display is to be continuously displayed even with the rotary axis set the axis as a linear axis Specify the direction of the motor rotation to the command direction. 0: Rotates clockwise (looking from motor shaft) with the forward rotation command. 1: Rotates counterclockwise (looking from motor shaft) with the forward rotation command. Specify whether the program movement amount is to be commanded with the diameter dimension or as movement amount. When the movement amount is commanded with the diameter dimensions 5mm will be moved when the command is a movement distance of 10mm. The movement amount per pulse will also be halved during manual pulse feed. Among parameters concerning length the tool length the wear compensation amount and the workpiece coordinate offset are displayed in diameter value when diameter is specified but other parameters are always displayed in radius value. Specify 1 when the NC control axis is used as the spindle.

Setting range (unit) 0: Linear axis 1: Rotary axis

0: Rotates clockwise 1: Rotates counterclockwise

0: Command with movement amount 1: Command with diameter dimension

1021 mcp_no (PR)

Amplifier I/F channel No. (servo)

1022 axname2 2nd axis (PR) name

0: The NC control axis is used as the servo axis. 1: The NC control axis is used as the spindle. Using a 4-digit number, set the amplifier interface 0000 channel No. and which axis in that channel is to be 0101 to 0107 used when connecting an axis amplifier. 0201 to 0207 High-order two digits : Amplifier interface channel No. Low-order two digits : Axis No. When using the conventional fixed layout, set all axes to 0000. Set the name of the axis displayed on the screen Two digits between A to with two characters. (X1, Z2, etc.) Z and 1 to 9 (Setting is cleared when 0 is set)

II - 24

5.

BASE SPECIFICATIONS PARAMETERS

# 1023 (PR)

crsadr

1024 (PR)

crsinc

Items Command address during cross machining Incremental command address during cross machining

Details Setting range (unit) Set the address for issuing a command to this axis A to Z during cross machining control. (Setting is cleared when 0 is set) Set the address for issuing an incremental command to this axis during cross machining control. A to Z (Setting is cleared when 0 is set)

(SETUP PARAM 1. 2/15) # Items 1025 l_plane Initial plane selection Details Setting range (unit) Specify the plane to be selected when the power is 1: X-Y plane (G17 turned ON or reset. command state) When 0 is specified, 1 is assumed (X-Y plane). 2: Z-X plane (G18 command state) 3: Y-Z plane (G19 command state) Specify the basic axis address that composes the Control axis addresses plane. such as X, Y, and Z Specify the axis address set in #1013 axname. If all three items do not need to be specified such as for 2-axis specifications input 0 and the parameter will be blank. Normally when X Y and Z are specified respectively for base_l_J_K the following relation will be established: G17: X-Y G18: Z-X G19: Y-Z Specify the desired address to set an axis address other than the above. If there is an axis parallel to #1026 base_l specify Control axis addresses that axis address. such as X, Y, and Z If there is an axis parallel to #1027 base_J specify Control axis addresses that axis address. such as X, Y, and Z If there is an axis parallel to #1028 base_K specify Control axis addresses that axis address. such as X, Y, and Z

1026 base_l 1027 base_J 1028 base_K

Base axis I Base axis J Base axis K

1029 aux_I 1030 aux_J 1031 aux_K

Flat axis I Flat axis J Flat axis K

II - 25

5.

BASE SPECIFICATIONS PARAMETERS

# Items 1037 cmdtyp Command type

Details Specify the program G code series and compensation type.

cmdtyp 1 G code series System 1 (for M) Compensation type Type A (one compensation amount for one compensation number) Type B (shape and wear amounts for one compensation number) Type C (two kinds of compensation amount of shape and wear per compensation No.) Same as above Same as above Same as above Same as above Same as above

Setting range (unit) 1 to 8

System 2 (for M)

System 2 (for L)

4 5 6 7

System 3 (for L) System 4 (for special L) System 5 (for special L) System 6 (for special L) System 7 (for special L)

1038 plcsel

Ladder selection

1039 spinno

Number of spindles

1040 M_inch (PR) 1041 l_inch (PR) 1042 pcinch (PR)

Constant input (inch) Initial state (inch) PLC axis command (inch)

There are some items in the specifications that can be used or cannot be used according to the value set in this parameter. The file structure may also change depending on the compensation data type. Thus after changing this parameter initialize the system with #1060 SETUP. Specify the PLC type. 0: User custom PLC 1: Standard PLC 2: Exclusive PLC for MELSEC bus link Specify the existence of a spindle. 0: No spindle 1: One spindle 2: Two spindles 3: Three spindles 4: Four spindles Specify the parameter unit system for the position 0: Metric system and length. 1: Inch system Specify the unit system for the program movement 0: Metric system amount when the power is turned ON or reset and for 1: Inch system position display. Designate an internal unit. Specify the unit system for the commands to the PLC 0: Metric system axis. 1: Inch system

II - 26

5.

BASE SPECIFICATIONS PARAMETERS

# 1043 lang

Items Select language displayed

Details Specify the display language. 0: 1: 2: 3: 11: 12: 13: 14: 15: 16: 17: 18: 19: 20: 22: Japanese display English display Third language displayed (Note) Fourth language displayed (Note) Display in German Display in French Display in Italian Display in Spanish Display in Chinese (traditional Chinese) Display in Korean Display in Portuguese Display in Dutch Display in Swedish Display in Hungarian Display in Chinese (simplified Chinese) (Standard) (Standard) (Option) (Option) (Option) (Option) (Option) (Option) (Option) (Option) (Option) (Option) (Option) (Option) (Option)

Setting range (unit) 0 to 3 11 to 22

1044 auxno (PR) 1045 nskno (PR)

Specify the number of NSK megatorque motors 0 to 16 connected. When a value other than 0 is specified, 2nd miscellaneous function data is output as signed binary data. 1049 mmac_R Machine Select the memory area for the machine 0/1 (PR) maker macro manufacturer macro program. RAM-ROM 0: SRAM area changeover 1: FROM area When this parameter is changed, the power must be turned OFF and ON, and the area must be formatted. Note: 1 cannot be set if the machine manufacturer macro option is not valid. Note: Selection of inch and metric unit When set value of #1041 I_inch is changed the unit of length is changed after reset. Among parameters concerning length following items are not changed automatically therefore change the set values to agree with the new unit system when the unit system is changed.

MR-J2-CT Connections Megatorgue motor connections

If no character package is available for a specified language, the screen is displayed in English. Specify the number of MR-J2-CTs connected. 0 to 4

Note:

II - 27

5.

BASE SPECIFICATIONS PARAMETERS

Tool compensation amount (Tool length compensation amount tool wear compensation amount and tool tip compensation amount) Workpiece coordinate offset #8004 SPEED #8027 Toler-1 #8056 G74 RETRACT #8005 ZONE r #8028 Toler-2 #8057 G76 LAST-D #8006 ZONE d #8029 FairingL #8075 SpiralEndErr #8009 DSC. ZONE #8030 MINUTE LENGS #8077 InvoluteErr #8010 ABS. MAX. #8037 CorJudgeL Machining #8011 INC. MAX. #8041 C-rot. R parameter #8084 G83S Clearanse #8012 G73n #8042 C-ins. R #8013 G83n #8051 G71 THICK #8085 G83S Forward F #8016 G71 MINIMUM #8052 PULL UP #8086 G83S Back F #8017 G71 DELTA-D #8053 G73U #8018 G84/G74n #8054 W Axis parameter #8204 OT-CHECK-N #8205 OT-CHECK-P #8206 TOOL CHG.P #8209 G60 Shift Barrier data #8300 #8306, #8311 #8314 Basic specification #1084 RadErr parameter #8004 SPEED is 10 inches/min. unit for the inch system.

II - 28

5.

BASE SPECIFICATIONS PARAMETERS

# Items Details 1050 MemPrg Program area Set the area for saving the program when (#1001 (PR) selection SYS_ON[2]) is set to 1. 2-system 0: Regardless of the system, the program is saved in one area. 1: The program can be saved for each system. Setting MDI 0, 1, 4, 5: MDI data is common for systems. data per 2, 3, 6, 7: MDI data can be set for each system. system (Internally, 200000000 is added to use data for each system.) Changeover to 0 to 3: The machine manufacturer macro use machine program is used commonly in systems. manufacturer 4 to 7: Machine manufacturer macro can be macro registered for each system. Select the commonly for system for registering the macro program systems or for with the system selection signal, and then each system edit. 1051 MemTol Tool 0: Tool compensation memory separate for (PR) compensasystems tion memory 1: Tool compensation memory common for common for systems systems 1052 MemVal No. of 0: Common variables common for system (PR) common (number fixed) variables #100 to : Per system shared in #500 to : Common for systems system 1: Common variables common for system designation (number fixed) #100 to : Designate with V1comN #500 to : Designate with V0comN * When this parameter is changed, the method of reading the file system will change after the power is turned ON, so always reformat again. Setting order
MemVal changeover Format Mismatch displays Turn power ON again

Setting range (unit) 0/1

0 to 7

0 to 7

0/1

0/1

Format

II - 29

5.

BASE SPECIFICATIONS PARAMETERS

# Items 1060 SETUP Activate setup processing

Details Execute the functions required for initializing the system.

Setting range (unit) 1

1: Execute one-touch setup

#(1060) Data( 1)( )
INPUT

"BASE PARA. SET? (Y/N)" is displayed.

To initialize the parameters.

To retain the current parameters.

INPUT

INPUT

The parameters are initialized according to the setting values in #1001 to #1043.

"FORMAT?(Y/N)" is displayed.

To initialize the machining program file and tool offset file.

To retain the current machining program file and tool offset file.

INPUT

INPUT

The above files are initialized and the standard canned cycle program is input.

"SETUP COMPLETE" is displayed.

Note:

Most setup parameters will be initialized with one-touch setup so confirm the data before executing. This parameter will automatically be set to 0 when the power is turned ON.

II - 30

5.

BASE SPECIFICATIONS PARAMETERS

(SETUP PARAM 1. 3/15) # 1061 intabs (PR) Items Manual ABS updating Details Setting range (unit) Defines whether to update the absolute value data 0: Do not update during automatic handle interrupt. (shift coordinates This parameter is valid only when #1145 l_abs is set the amount of the to 1. interruption) 1: Update (same coordinates as when interrupt did not occur will be applied.) Specify whether the tool length offset and wear 0 to 3 compensation is valid during T command execution.

1062 T_cmp

Tool offset function

Setting value 0 1 2 3

Tool length offset Valid Valid Invalid Invalid

Wear compensation Valid Invalid Valid Invalid

1063 mandog

Manual dog-type

1064 svof (PR)

Error correction

The initial return to the reference point is performed 0: High speed return with dog-type return after the power is turned ON and 1: Dog-type the coordinate system is established. Specify the manual reference point return method after the coordinate system is established with this parameter. (This setting is not required when using absolute position detection.) Specify whether to correct the error when the servo is 0: Do not correct the OFF. error 1: Correct the error

II - 31

5.

BASE SPECIFICATIONS PARAMETERS

# Items 1065 JOG_H JOG response type

1066 JOG_HP

1067 JOG_HN

1068 slavno (PR)

Details Set up an improved JOG response type. 0: Conventional specification The system is started and stopped by signal via ladder without reference to external input signals. 1: Type 1 The system is started up and stopped by external signal. 2: Type 2 The system is started up and stopped by performing the AND operation for external signals and those via ladder. 3: Type 3 The system is started up when signals via ladder rise. It is stopped when external signals and those via ladder fall. 4: Type 4 Zero point return mode: The system is started up and stopped by signal via ladder without reference to external input signals (conventional specification). Non-zero point return mode: The system is started up and stopped by performing AND for external signals and those via ladder (type 2). Select JOG Specify the number of the device that inputs +JOG activation signals. The device type is specified by activation (+) device JOG_D in #1071. The effective range of set values vary depending on the device type. A value outside of the effective range is invalid if specified. Select JOG Specify the number of the device that inputs -JOG activation activation signals. The device type is specified by JOG_D in #1071. The effective range of set values () device vary depending on the device type. A value outside of the effective range is invalid if specified. Slave axis Specify the number of the slave axis for synchronous number control. The axis number is an NC number excluding the spindle and PLC axis. Two or more slave axes cannot be set up for one master axis. slaveno cannot be set up for a slave axis. A dual system cannot be set up so that the relationship between the master and slave axes extends over a system.

Setting range (unit) 0 to 4

X: 0000 to 013F (hexadecimal) G: 0000 to 3071 M: 0000 to 5119 (decimal) X: 0000 to 013F (hexadecimal) G: 0000 to 3071 M: 0000 to 5119 (decimal) 0: No slave axis 1 to 4: First to fourth axes 1 to 14: 1st axis to 14th axis (For simple C axis synchronous control)

II - 32

5.

BASE SPECIFICATIONS PARAMETERS

# Items Details Setting range (unit) 1069 no_dsp Axis with no Set up an axis that displays no counter. This option is 0: Displays the (PR) counter valid on the counter display screen (relative value counter 1: Does not display display screen). the counter. 1070 axoff Axis Define an axis that enables axis removal control. 0: Disables axis removal removal. 1: Enables axis removal 1071 J0G_D 0 to 2 J0G Specify the number of the device that inputs J0G (PR) activation activation signals. signal 0: X device device 1: G device 2: M device name Set the JOG_HP (#1066) and JOG_HN (#1067) parameters according to this device specification parameter. 1072 chop_ax Chopping Designate the chopping axis. 0: Non-chopping axis axis 1: Chopping axis

II - 33

5.

BASE SPECIFICATIONS PARAMETERS

(SETUP PARAM 1. 4/15) # Items Details 1073 I_Absm Initial absolute Specify the absolute value/incremental value value mode for when the power is turned ON or reset. Setting range (unit) 0: Incremental value command mode 1: Absolute value command mode 0: Asynchronous feed 1: Synchronous feed

1074 l_Sync

Initial synchronous feed Initial G00

1075 I_G00

1076 Abslnc (For L system only)

ABS/INC address

1077 radius

1078 Decpt2

1079 F1digt

1080 Dril_Z (For D system only)

Incremental command for diameter specification axis Decimal point Specify the unit of position commands that do not type 2 have a decimal point. 0: The min. input command unit is used (follows #1015 cunit) 1: 1mm (or 1inch) unit is used (For the dwell time, 1s unit is used.) Validate F1 Specify whether to execute the F command with a digit 1-digit code command or with a direct numerical command. 0: Direct numerical command (command feedrate during feed per minute or rotation) 1: 1-digit code command (feedrate specified with #1185 spd_F1 #1189 F5) Specify boring Specify a fixed cycle hole drilling axis. axis 0: Use an axis vertical to the selected plane as the hole drilling axis. 1: Use the Z axis as the hole drilling axis regardless of the selected plane.

Specify the feedrate specification mode for when the power is turned ON or reset. 0: Asynchronous feed (feed per minute) 1: Synchronous feed (feed per rotation) Specify the linear command mode for when the power is turned ON or reset. 0: Linear interpolation (G00 command state) 1: Positioning (G01 command state) The absolute value/incremental commands can be issued by using the absolute value address and incremental value address for the same axis. 0: Absolute/incremental with G command 1: Absolute/incremental with address code (The #1013 axname address will be the absolute value command and #1014 incax address will be the incremental value command) Specify if the diameter specification axis (#1019 dia is set to 1) incremental value command uses the diameter value or radius value

0: Linear interpolation 1: Positioning

0: Absolute/ incremental with G command 1: Absolute/ incremental with address code

0: Diameter value 1: Radius value

0: The min. input command unit is used 1: 1mm (or 1inch) unit is used 0: Direct numerical command 1: 1-digit code command

0/1

II - 34

5.

BASE SPECIFICATIONS PARAMETERS

# 1081

1082

1084

1085

1086

1087

1088

1089

Items Details Setting range (unit) Gmac_P Give priority Specify the G code priority relationship during the 0/1 to G code macro call with the G command. parameter 0: G code used in system is priority. 1: Registered G code for call out is priority. Geomet Geometric Specify whether to use the geometric I or IB function. 0/1/2 (For L 0: Do not use. system 1: Use only geometric I. only) 2: Use geometric I and IB. With geometric, specific address codes are used for exclusive meanings. Thus, if A or C is used for the axis address or 2nd miscellaneous command code, the A used for the axis address may function as the geometric's angle designation. Take special care when designating the axis name, etc., when using this function. RadErr Arc error Specify the tolerable error range when a deviation 0 to 1.000 (mm) occurs in the end point and center coordinate in the circular command. G00Drn G00 dry run Specify whether to apply dry run (feed with manual 0: Do not apply to setting speed instead of command feedrate) to the G00 G00 command. 1: Apply to G00 0: Do not apply to G00. (move at rapid traverse rate) 1: Apply to G00. (move at manual set feedrate) 0/1 G0lntp G00 Specify the G00 movement path type 0: Move linearly toward the end point. non-interpol ation (interpolation type) 1: Move to the end point of each axis at the rapid traverse feedrate for each axis. (non-interpolation) G96_G0 Constant Specify how to handle the cycle speed for the G00 0/1 surface command when using the constant surface speed speed control function. control by 0: Calculate the cycle speed constantly even rapid during G00 movement. traverse 1: Calculate the cycle speed at the block end feed point in the G00 command. command G30SL Disable G30 Specify how to handle the soft limit during G30 (2nd 0: Soft limit valid soft limit reference point return) movement. 1: Soft limit invalid 0: Soft limit valid during G30 movement 1: Soft limit invalid during G30 movement Cut_RT Short cut for Specify how to handle the short cut control for the 0: No short cut rotary axis rotary axis (#1017 rot is set to 1). 1: Use short cut 0: No short cut (move toward end point) 1: Use short cut (when using the absolute value command move in the direction where the movement amount will be 180 or less)

II - 35

5.

BASE SPECIFICATIONS PARAMETERS

# 1090 Lin_RT

Items Linear rotary axis

1091 Mpoint

1092 Tchg _A

1093 Wmvfin

1094 Tl_SBK (for L system only)

Details Specify how to handle a command for the rotary axis that exceeds 360. 0: For absolute value commands that exceed 360 the value will be converted into a remainder of 360 and the axis will move. Example: If the command is 420 the applied value will be 60. 1: For absolute value commands that exceed 360 the axis will move in the same manner as a linear axis. Example: If the command is 420 the axis will pass the 360 position and will move to the 60 position. Ignore Specify now to handle the middle point during G28 middle point and G30 reference point return. 0: Move to the reference point after passing the middle point designated in the program. 1: Ignore the middle point designated in the program and move straight to the reference point. Replace tools Specify the movement of the additional axis during for additional tool change position return. axis 0: The additional axis does not move with the tool change position return command. 1: After returning the standard axis with the tool change position return command the additional axis also returns to the tool change position. Inter-system Specify the method for waiting between systems when using two systems. waiting method When the movement command is found in the wait command (!, M) block: 0: Wait before executing movement command 1: Wait after executing movement command Select life Select whether to count the data units to be used for count for a single block when using the tool life management II single block function (L system). 0: Does not count the data units. 1: Count the data units.

Setting range (unit) 0/1

0/1

0/1

0/1

0/1

II - 36

5.

BASE SPECIFICATIONS PARAMETERS

# 1095 T0tfof

Items TF output

1096 T_Ltyp (for L system only) 1097 T1digt

Tool life management type Tool wear compensation number 1-digit command

Details Select how to handle TF for T00 command. 0: TF is output. 1: TF is not output Specify the tool life management type.

Setting range (unit) 0/1

1098 Tlno.

Tool length offset number

1099 Treset

Cancel tool wear compensation amount

Specify the No. of digits in the tool wear compensation No. in the T command. 0: The 2 high-order digits are the tool No. and the 2 Iow-order digits are the wear compensation No. 1: The 3 high-order digits are the tool No. and the 1 Iow-order digit is the wear compensation No. This parameter will be fixed to 0 when tool life management II is selected. Specify the No. of digits in the tool length offset No. 0/1 in the T command. 0: The 2 or 3 high-order digits are the tool No. The 2 or 1 Iow-order digits are the tool length offset and wear compensation Nos. 1: The 2 or 3 high-order digits are the tool No. and tool length offset Nos. The 2 or 1 Iow-order digits are the wear compensation No. Specify how to handle tool compensation vector 0: Clear when resetting system. 1: Save 0: Clear the tool length and wear compensation vectors when resetting. 1: Save the tool length and wear compensation vectors when resetting. When the values are cleared the compensation will not be applied so the axis will move the compensation amount in the next compensation operation. When the values are saved the compensation will be applied so the axis will shift the differential amount of the compensation amount in the next compensation operation.

1: Life management type l 2: Life management type ll 0/1

II - 37

5.

BASE SPECIFICATIONS PARAMETERS

# 1100 Tmove

Items Tool wear compensation

1101 Tabsmv

1102 tlm (For L system only) 1103 T_life

Details Specify the period to perform tool length offset and wear compensation. 0: Compensate when T command is executed. 1: Superimpose and compensate with the movement command in the block where the T command is located. If there is no movement command in the same block compensation will be executed after the movement command is superimposed in the next movement command block. 2: Compensate when the T command is executed. 1: Superimpose and compensate a tool length offset with the movement command in the same block. If there is no movement command in the same block, compensation will be executed after the movement command is superimposed in the next movement command block. Tool wear Specify the type of movement command when #1100 compensation method Tmove is set to 1. 0: Compensate regardless of the movement command type. 1: Compensate only at the movement command in the absolute value command. Manual tool Specify the measurement method for manual tool length measurement l. measuring 0: Align tool with reference position system 1: Input measurement results Validate life Select the usage of the tool life management management function.

Setting range (unit) 0 to 2

0: Compensate regardless of the command type. 1: Compensate only with the absolute value command.

1104 T_Com2 Tool command method 2

0: Reference position method 1: Measured value input method 0: Do not use. 1: Perform tool life management control. Select the command method for when #1103 T_Life 0/1 is set to 1. 0: Handle the program tool command as the group No. 1: Handle the program tool command as the tool No.

II - 38

5.

BASE SPECIFICATIONS PARAMETERS

# 1105 T_Sel2

Items Tool selection method 2

1106 Tcount (For L system only) 1107 Tllfsc (For L system only)

Life management count Split life management display screen

Details Select the tool selection method for when #1103 T_Life is set to 1. 0: Select in order of registered No. from the tools used in the same group. 1: Select the tool with the longest remaining life from tools used in the same group and the unused tools. Specify the function when address N is omitted when inputting data (G10 L3 command) for tool life management function ll.

Setting range (unit) 0/1

1108 TlrectM (For L system only) 1109 subs_M (PR)

Life management re-count M code Validate alternate M code M96 alternate M code M97 alternate M code Validate status trigger system

0: Time specified input 1: No. of times specified input Set up the number of groups to be displayed on the 0 to 2 tool life management II (L system) screen. 0: Displayed group count 1, maximum number of registered tools: 16 1: Displayed group count 2, maximum number of registered tools: 8 2: Displayed group count 4, maximum number of registered tools: 4 Set up the M code for tool life management II (L 0 to 99 system) re-count.

Select the user macro interrupt with the substitute M code.

1110 M96_M 1111 M97_M 1112 S_TRG (PR)

Specify an M code to replace M96 when #1109 subs_M is set to 1. Specify an M code to replace M97 when #1109 subs_M is set to 1. Specify the validity conditions for the user macro interrupt signal. 0: Valid when interrupt signal (UIT) turns OFF to ON. 1: Valid when interrupt signal (UIT) is ON.

1113 INT_2 (PR)

Validate interrupt method type 2

Specify the movement after user macro interrupt signal (UIT) input. 0: Execute interrupt program without waiting for block being executed to end. 1: Execute interrupt program after completing block being executed.

0: Alternate M code invalid 1: Alternate M code valid 3 to 97 (excluding 30) 3 to 97 (excluding 30) 0: Valid when interrupt signal (UIT) turns OFF to ON. 1: Valid when interrupt signal (UIT) is ON. 0/1

II - 39

5.

BASE SPECIFICATIONS PARAMETERS

# 1114 mcrint

Items Macro argument initialization

1115 thwait

1116 G30SLM

1117 H_sens

Waiting for thread cutting Invalidate soft limit (manual operation) Handle response switch

Details Select whether to clear statements other than specified arguments by macro call. Also, select whether to clear local variables by power-ON and resetting. 0: Delete non-specified arguments by macro call. 1: Retain non-specified arguments by macro call. 2: Retain non-specified arguments by macro call and clear local variables by power-ON and resetting. Set the queue number during screw thread cutting when the chamfering is not valid. Enable this function when disabling the soft limit check function from the second to the fourth zero point return by manual operation.

Setting range (unit) 0/1/2

0 to 99 (Approx. 4 ms.) Standard set value: 4

1118 mirr_A (For L system only)

1119 Tmiron (For L system only)

1120 TofVal (PR)

0: Enable soft limit function. 1: Disable soft limit function. Switch the handle response mode when feeding the 0/1 handle. 0: Standard handle response 1: High-speed handle response Select how to Select one of the following two methods: 0/1 set up the Set up the current length of tools on each length of facing turret. tools on Set up a value, assuming that the tools on cutter tables each facing turret are in the same direction as (opposed that of those on the base turret. tables) 0: Current length of the tools on each facing turret 1: Value, assuming that the tools on each facing turret are in the same direction as that of those on the base turret. Select the Select whether to validate the mirror image of each 0: Invalid mirror image facing turret with the T command. 1: Valid of each facing turret with T command Change Specify whether to change the macro variable (tool 0/1 macro offset) numbers for shape compensation and wear variable compensation. 0: Do not change. (Conventional specifications) 1: Change the shape and wear compensation variable numbers each for X, Z, and R.

II - 40

5.

BASE SPECIFICATIONS PARAMETERS

(SETUP PARAM 1. 5/15) # 1121 edlk_c Items Edit lock C Details Specify whether to prohibit editing of program Nos. 9000 to 9999. Note: If #1122 is set to 1 or 2, 1 will be set in #1121 when the power is turned ON. The display and search of program Nos. 9000 to 9999 can be prohibited. Specify whether to prohibit display and search. 0: Display and search is possible. 1: Program details are not displayed. 2: Program details are not displayed and operation search is prohibited. The program details will not be displayed but the program No. and sequence No. will display in the prohibited state. Note: If #1122 is set to 1 or 2, 1 will be set in #1121 when the power is turned ON. Select whether to use the origin zero function. Setting range (unit) 0: Editing possible 1: Editing prohibited

1122 pglk_c (PR)

Program display lock

0 to 2

1123 origin 1124 ofsfix

1125 real_f

1126 PB_G90

1127 DPRINT

Origin zero inhibition Fix tool wear Specify whether to automatically increment the offset No. by 1 with the input or to display the No. as compensation number it is in the setting on the tool offset screen. 0: Increment the # No. by 1 when the input key is pressed. (Same as general parameters) 1: # No. does not change even if INPUT key is pressed. When making settings in sequence 0 is handier. When changing and setting repeatedly while adjusting one offset value 1 is handier Actual Specify the feedrate display on the monitor screen. feedrate display Playback G90 Specify whether the playback movement amount when performing playback editing is to be an absolute value or incremental value. DPRINT Specify the alignment for printing out with the alignment DPRINT function. 0: No alignment data is printed with left justification. 1: Align the minimum digit and output.

0: Use 1: Do not use 0/1

0: Command speed 1: Real movement feedrate 0: Incremental value 1: Absolute value 0/1

II - 41

5.

BASE SPECIFICATIONS PARAMETERS

# Items 1128 RstVCI Clear variables by resetting

1129 PwrVCl

1130 set_t

1131 Fldcc (PR)

Details Specify how to handle the common variables when resetting. 0: Common variables do not change after resetting. 1: The following common variables are cleared by resetting: During variable 100 group specifications: #100 to #149 are cleared. During variable 200 group and 300 group specifications: #100 to #199 are cleared. Clear Specify how to handle the common variables when the variables by power is turned ON. power-ON 0: The common variables are in the same state as before turning the power OFF. 1: The following common variables are cleared when the power is turned ON. During variable 100 group specifications: #100 to #149 are cleared. During variable 200 group and 300 group specifications: #100 to #199 are cleared. Display Specify the tool command value display on the selected tool POSITION screen. number 0: T-modal value of program command is displayed. 1: Tool number sent from PLC is displayed. Feed forward Parameter to suppress acceleration changes with a filter filter when starting acceleration or deceleration Specify the parameter in bits. 7 6 5 4 3 2 1 0

Setting range (unit) 0/1

0/1

0/1

bit1: 7.1 (ms) bit2: 14.2 (ms) bit3: 28.4 (ms) bit4: 56.8 (ms) If bit 1 to bit 4 are all 0 or two or more bits of bit 1 to bit 4 are 1, 3.5 ms is set up. 3 to 3

Feed forward filter 1132 CRT CRT brightness control This parameter adjusts the brightness of the CRT display unit. 3: Highest luminance (Brightest state) 3: Lowest luminance (Darkest state) Adjust this parameter to an appropriate brightness between 3 and 3. The EL display unit does not have brightness adjustment so setting is not required.

II - 42

5.

BASE SPECIFICATIONS PARAMETERS

# Items Details 1133 ofsmem Select how to Select the number stored by previous setup when set up tool selecting the tool wear compensation screen. wear 0: Does not display the number when selecting compensathe screen. tion screen 1: Displays the stored number when selecting the screen. 1134 LCDneg LCD reverse Specify 1 to reverse the display on the 10.4-type display monochrome LCD. 1135 unt_nm Unit name Set up a unit name. Set up the unit name with 4 or less characters consisting of both alphabets and numbers. If 0 is set up, the unit name is not displayed. 1136 optype Operation This parameter validates the operation menu display. menu display Specify the setting method for the tool offset datas valid absolute value or incremental value. 0: Mode selection method (Conventional specification) 1: Menu selection method This parameter is valid on the following screens. TOOL TIP OFFSET screen (L system) TOOL DATA screen (L system) NOSE-R screen (L system) TOOL OFFSET screen type I (M system) TOOL OFFSET screen type II (M system) 1137 Cntsel Coordinate Set the type of the position counter to be displayed on value screen the COORDINATE screen. display counter 0 : MST (Default) select
1 2 3 : Next command : Current value B : Manual interrupt amount

Setting range (unit) 0/1

0: Normal display 1: Reverse display 4 or less characters consisting of both alphabets and numbers 0/1

1st digit : 0 to 3 2nd digit: 0 to 3 (Default : 00)

0 or 1 : Next value (Default) 2 3 : Current value B : Manual interrupt amount

1138 Pnosel

Select screen by parameter number:

Specify whether to enable the function to select a screen by specifying a parameter number.

0: Disable 1: Enable

II - 43

5.

BASE SPECIFICATIONS PARAMETERS

# Items 1139 edtype Edit type selection

Details Set up an edit type. 0: Screen edit type (M50 or equivalent operation) 1: Screen edit type (The screen of EDIT or MDI is changed automatically according to the selected operation mode.) 2: Word edit type (The screen of EDIT or MDI is changed automatically according to the selected operation mode.) 3: Screen edit type (type 0 + retaining cursor position) (Applicable only to M64 D version series) 4: Screen edit type (type 1 + retaining cursor position) (Applicable only to M64 D version series) First number of M code that corresponds to setup number from 100 to 199 First number of M code that corresponds to setup number from 200 to 299 First number of M code that corresponds to setup number from 300 to 399 First number of M code that corresponds to setup number from 400 to 499 Select whether to enable MDI setup in non-MDI mode.

Setting range (unit) 0/1/2/3/4

1140 Mn100 1141 Mn200 1142 Mn300 1143 Mn400 1144 mdlkof 1145 I_abs

1146 Sclamp

1147 smin_V

M code number M code number M code number M code number MDI setup lock Manual ABS Specify how to handle the absolute value data during parameter automatic handle interrupt. 0: Absolute value data is renewed if manual ABS switch is ON. Data is not renewed if switch is OFF. 1: Follows the intabs state when #1061 intabs is valid. Spindle Specify how to handle the spindle rotation speed clamp rotation function with the G92S command. speed 0: G92S command is handled as a clamp command clamp only in the G96 state (during constant surface function speed control). G92S will be handled as normal S command in G97 state (constant surface speed OFF). 1: The S command in the same block as G92 is constantly handled as a clamp command. Minimum Specify the type of spindle min. rotation speed clamp spindle value. rotation 0: Rotation speed setting speed 1: Output voltage coefficient setting clamp type Set the #3023 smini parameter according to this type setting.

0 to 99999999 0 to 99999999 0 to 99999999 0 to 99999999 0: Disable MDI setup 1: Enable MDI setup 0/1

0/1

0: Rotation speed setting 1: Output voltage coefficient setting

II - 44

5.

BASE SPECIFICATIONS PARAMETERS

# Items 1148 I_G611 Initial high precision 1149 cireft Arc deceleration speed change G00 feed forward filter

1150 F1dc0

Details Specify the default mode after power-ON or resetting. 0: G64 (cutting mode) 1: G61.1 (high precision control mode) Specify whether to enable deceleration at the arc entrance or exit. 0: Disable 1: Enable This parameter is used to filter acceleration changes at the start of rapid acceleration/deceleration. Specify the filters in bit units. 7 6 5 4 3 2 1 0

Setting range (unit) 0/1

0/1

bit1: 7.1 (ms) bit2: 14.2 (ms) bit3: 28.4 (ms) bit4: 56.8 (ms) When bits 1 to 4 are all 0 or when two or more of bits 1 to 4 are 1, 3.5 (ms) is assumed.

G00 feed forward filter Feed forward filter G00/G01 separation 0: Common 1: Separation 1151 rstint

1152 I_G20

1153 FixbDc

Specify whether to initialize various modals by resetting. 0/1 0: Don't initialize. 1: Initialize. Initial Specify whether the default mode after power-ON or 0/1 resetting, inch command or metric command mode. command unit 0: Metric command (G21 command state) 1: Inch command (G20 command state) Valid when reset input is made. Related parameter: Bit 6 Select setting and display unit of #1226 Hole bottom Specify whether to perform a deceleration check or 0 to 2 deceleration in-position check at the hole bottom in the hole drilling check cycle. This parameter is valid only for a hole drilling cycle in which no dwell command can be issued at the hole bottom. 0: Perform no deceleration check and in-position check. 1: Perform a deceleration check. 2: Perform an in-position check.

Reset initial

II - 45

5.

BASE SPECIFICATIONS PARAMETERS

# 1154 pdoor (PR)

Items Details Setting range (unit) Door interlock Specify whether to control door interlock II 0/1 II (for each independently for each of the two systems. When door system) interlock II is controlled for each system of the two systems, system 1 is connected to SV1 (channel 1) of the base I/O unit and system 2 is connected to SV2 (channel 2) of the base I/O unit. Base I/O unit
SV1

AMP

AMP

AMP

System 1

SV2

AMP

AMP

AMP

System 2

When the auxiliary axis (MR-J2-CT) is used, connect it to the SV2 side (after the spindle). This validates door interlock II of system 2. 0: Do not use door interlock II independently for channels. 1: Use door interlock II independently for channels. (Separate systems when using two systems) 2: Use door interlock II independently for channels. (Use independently for system 1 channels) (Use both for system 2) When 0 is specified for this parameter, Signal input device 1 for door interlock II (#1155 DOOR_m) and Signal input device 2 for door interlock II (#1156 DOOR_s) are valid. When 1 is specified, Signal input device 1 for door interlock II: for each system (#1511 DOORPm) and Signal input device 2 for door interlock II: for each system (#1512 DOORPs).

II - 46

5.

BASE SPECIFICATIONS PARAMETERS

# Items 1155 DOOR_m Signal input device 1 for door interlock II

1156 DOOR_s

1157 F0atrn

1158 F0atno

1165 p_trans

Device number 2 for door interlock II signal input F0 automatic running F0 automatic running program Parameter FROM backup

Details Set up a fixed device number (X??) for door interlock II signal input. A device number from X01 to XFF can be set up. Device number 000 is invalid. Set up device number 100 when using no fixed device number for door interlock II signal input. Related parameter: #1154 pdoor Door interlock II (for each system) Set up a fixed device number (X??) for door interlock II signal input. (Set up the same value as that of #1155.) Related parameter: #1154 pdoor Door interlock II (for each system) Not used

Setting range (unit) 000 to 100 (Hexadecimal)

000 to 100 (Hexadecimal)

Not used

1166 fixpro

Fixed cycle editing

1167 e2rom 1168 test

Simulation test

The parameters are written, read and compared. 0: No process 1: The backed up parameters are read from the FROM. 2: The parameters are written into the FROM. 3: The parameters are compared with those backed up in the FROM. Select whether to use the edit, program list and data input/output functions for the fixed cycles, machine manufacturer macro programs or general programs. 0: General programs can be edited, etc. 1: The fixed cycles can be edited, etc. Password No.: The machine manufacturer macro programs can be edited, etc. Not used. Specify the test mode for the control unit. The test mode does not use reference point return and tests with a hypothetical zero point return completed state. This is limited to test operation of the control unit itself and must not be used when connected to the machine.

0 to 3

0 to 99999999

0: Normal operation mode 1: Test mode

II - 47

5.

BASE SPECIFICATIONS PARAMETERS

(SETUP PARAM 1. 6/15) # 1169 system name Items Details System name Set the name of each system. This must be set only when using two systems. This name is displayed on the screen only when the systems must be identified. Use a max. of four alphabetic characters or numerals. 1170 M2name Second Set this address code when using the 2nd miscellanemiscellaneous command. Set an address with A B ous code and C that is not used with #1013 axname or #1014 incax. 1171 taprov Tap return Set the tap return override value for the synchronous override tap. 1172 tapovr Tap return Set the override value when leaving the tap end point override in the synchronous tap cycle. The setting range is 1 to 999 and the unit is %. When a value less than 100 is set it will be judged as 100%. 1173 dwlskp G04 skip Specify the skip signal for ending the G04 (dwell) condition command. Setting range (unit) A max. of four alphabetic characters or numerals.

A, B, C

1 to 100 (%) 1 to 999 (%)

Skip condition 0 to 7
Setting PLC interface input signal Skip 3 Skip 2 Skip 1

0 1 2 3 4 5 6 7

1174 skip_F

G31 skip speed

1175 skip1 1176 1177 1178 1179 1180 1f 2 2f 3 3f

G31.1 skip condition G31.2 skip speed G31.2 skip condition G31.2 skip speed G31.3 skip condition G31.3 skip speed

End when signal is input. Specify the feedrate when there is no F command in 1 to 999999 (mm/min) the program at G31 (skip) command. Specify the skip signal in the G31.1 to G31.3 Skip condition 0 to 7 PLC interface input signal (multi-step skip) command and the feedrate when Setting Skip 3 Skip 2 Skip 1 there is no F command in the program. 0 Skip signal specified at G31.1 1 Skip feedrate at G31.1 Skip signal specified at G31.2 Skip feedrate at G31.2 Skip signal specified at G31.3 Skip feedrate at G31.3
2 3 4 5 6 7

Skip feedrate 1 to 999999 (mm/min)

II - 48

5.

BASE SPECIFICATIONS PARAMETERS

# Items 1181 G96_ax Constant surface speed control

1182 thr_F

Thread cutting speed M code for clamp Dwelling time after outputting M code for unclamp F1 digit feedrate F1 F2 F3 F4 F5 Validate inclinedaxis control Inclination angle

1183 clmp_M 1184 clmp_D

Details Specify the axis to be targeted for constant surface speed control. 0: Program specification will be invalidated and the axis will always be fixed to the 1st axis. 1: 1st axis specification 2: 2nd axis specification 3: 3rd axis specification 4: 4th axis specification The program specification will be the priority for all settings other than 0. Set the screw cut up speed when not using chamfering in the thread cutting cycle. 0: Cutting feed clamp feedrate 1 to 60000 mm/min: Set feedrate Set the M code for C-axis clamp in the hole drilling cycle. Set the dwell time after outputting the M code for C-axis unclamp in the hole drilling cycle.

Setting range (unit) 0 to 4

0 to 60000 (mm/min)

0 to 99999999 0.000 to 99999.999 (s)

1185 1186 1187 1188 1189 1190 (PR)

1191 (PR)

1192 (PR)

spd_F1 spd_F2 spd_F3 spd_F4 spd_F5 s_xcnt (For L system only) s_angl (For L system only) s_zrmv (For L system only)

Specify the feedrate for the F command in the F1-digit command (#1079 F1 digt is set to 1). Feedrate when F1 is issued (mm/min) Feedrate when F2 is issued (mm/min) Feedrate when F3 is issued (mm/min) Feedrate when F4 is issued (mm/min) Feedrate when F5 is issued (mm/min) Specify whether to disable or enable inclined-axis control. 0: Disable inclined-axis control 1: Enable inclined-axis control Specify the inclination angle (). Note: If 0 is specified for this parameter, the angle determined by three-side setting is valid.

1 to 60000 (mm/min)

0/1

80.000 ()

Compensa Specify whether to perform compensation for the tion at base axis corresponding to the inclined axis at origin original return. return 0: Perform compensation. 1: Don't perform compensation.

0/1

II - 49

5.

BASE SPECIFICATIONS PARAMETERS

(SETUP PARAM 1. 7/15) # 1193 inpos Items Details The setting is selected with #1306 InpsTyp Deceleration check specification type. 0: Deceleration check method 1 1: Validate in-position check Deceleration Specify the deceleration check method for G0. check method 0: Command deceleration check 1 1: In-position check Validate Specify the deceleration confirmation method for the in-position positioning or cutting command. check 0: G0, G1+G9 Command deceleration check 1: G0, G1+G9 In-position check Time constant Specify the time constant for the manual handle 0 for handle feed. feed 0: Use time constant for G01 1: Time constant 0 (step) Specify the user macro M S or T command macro call out. Macro call for Macro call out with M command M command Macro call for S Macro call out with S command command Macro call for T command Macro call with 2nd miscellaneous code Select initial spindle control Macro call out with T command Setting range (unit)

0/1

0/1

1194 H_acdc

0/1

0: Invalid 1: Valid

1195 Mmac 1196 1197 Smac 1198 Tmac M2mac

Macro call out with 2nd miscellaneous command

1199 Sselect

1200 G0_acc (PR)

Select the initial condition of spindle control after power is turned ON. 0: 1st spindle control mode (G43.1) 1: Selected spindle control mode (G44.1) 2: All spindle simultaneously control mode (G47.1) Note: Spindle No. when G44.1 is commanded is selected with #1534 SnG44.1. Validate Set up acceleration and deceleration types when a acceleration rapid traverse command is issued and 0: Acceleration and deceleration (conventional) deceleration with time constant with inclination 1: Acceleration and deceleration with inclination angle constant angle constant G0

0: G43.1 1: G44.1 2: G47.1

0: Acceleration and deceleration with time constant 1: Acceleration and deceleration with inclination angle constant

II - 50

5.

BASE SPECIFICATIONS PARAMETERS

# 1201 G1_acc (PR)

1202 mirofs (For L system only) 1203 TmirS1 (For L system only) 1204 TmirS2 (For L system only) 1205 G0bdcc

Items Details Setting range (unit) Validate Set up acceleration and deceleration types when a 0: Acceleration and acceleration liner interpolation command is issued. deceleration with and 0: Acceleration and deceleration (conventional) time constant deceleration with time constant 1: Acceleration and with inclination 1: Acceleration and deceleration with inclination deceleration with constant G1 angle constant inclination angle constant Distance Set up the distance between tools (edges) (between 0 to 99999.999 (mm) between facing facing turrets). turrets Select turrets as facing turrets with T command Select turrets as facing turrets with T command Acceleration and deceleration before G0 interpolation Maximum speed Time constant Set up turrets as shown in the mirror image of 0 to FFFFFFFF facing turrets with the T command that corresponds to tool numbers 1 to 32. Set up turrets as shown in the mirror image of 0 to FFFFFFFF facing turrets with the T command that corresponds to tool numbers 33 to 64. 0: G00 acceleration and deceleration are selected 0/1 as those after interpolation. 1: G00 acceleration and deceleration are selected as those before interpolation. Set up a cutting feedrate when selecting 1 to 999999 (mm/min) acceleration and deceleration before interpolation. Set up a cutting feed time constant when selecting 1 to 5000 (ms) acceleration and deceleration before interpolation.
Speed

1206 G1bF 1207 G1btL

G1bF

G1btL

Time

1208 RCK

Arc radius error compensation factor

An arc radius error compensation can be increased 60.0 to +20.0 (%) and decreased from 60.0 to 20.0%.

II - 51

5.

BASE SPECIFICATIONS PARAMETERS

# 1209 cirdcc

Items Arc decelerati on speed 1210 RstGmd Modal G code reset

Details Specify the deceleration speed at the arc entrance or exit. Specify whether to initialize each G code group modal and the H and D codes when the system is reset. Specify the initialization items in bit correspondence. 0. Initialize. 1: Don't initialize. M system
0 1 2 3 4 5 6 7 8 9 A B C D E F Group 1 Move G modal Group 2 Flat selection modal Group 3 Absolute/increment command modal Group 5 Feed G modal Group 6 Inch/metric modal Group 7 Radius compensation modal Group 8 Length compensation modal Group 10 Fixed cycle return command modal Group 12 Workpiece coordinate system modal Group 13 Cut modal Grpup 15 Normal line control modal

Setting range (unit) 1 to 999999 (mm/min)

Specify a hexadecimal number.

10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F

Group 17 Constant surface speed control command modal Group 18 pole coordinate command modal Group 19 G command mirror modal Group 20 Spindle 2 control modal

H, D codes Spindle clamp rotation speed

The H code indicates the tool length offset number, and the D code indicates the tool radius compensation number. When bit 18 is set to ON, the H and D codes and group 8 G modal area retained. When bit 7 is set to ON, the H code and group 8 G modal are retained. (To be continued to the next page)

II - 52

5.

BASE SPECIFICATIONS PARAMETERS

Items

Details (Continued from the previous page) L system

0 1 2 3 4 5 6 7 8 9 A B C D E F Group 1 Move G modal Group 2 Flat selection modal Group 3 Absolute/increment command modal Group 4 Barrier check modal Group 5 Feed G modal Group 6 Inch/metric modal Group 7 Nose R compensation modal

Setting range (unit) Specify a hexadecimal number.

Group 10 Fixed cycle return command modal Group 12 Workpiece coordinate system modal Group 13 Cut modal

10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F

Group 17 Constant surface speed control command modal Group 18 Balance cut Group 20 Spindle 2 control modal Group 15 Facing turret mirror image

1211 FHtyp

1212 FHno

1213 proaxy (For L system only)

Feed hold stop Specify the type of the external signal used for feed type hold. 0: Disable the external signal. 1: Enable the external signal (contact A) 2: Enable the external signal (contact B) Feed hold Specify the number (X??) of the device used to input external signal the feed hold signal. device Side 1 of Specify the length on the rectangular coordinates of inclination the inclined axis in the triangle made up of the angle inclination angle.

0 to 2

000 to 13F (hexadecimal) 9999.999

II - 53

5.

BASE SPECIFICATIONS PARAMETERS

# Items 1214 macaxy Side 2 of (For L inclination system angle only) 1215 macaxx Side 3 of (For L inclination system angle only) 1216 extdcc External deceleration level

Details Specify the length of the actual base axis corresponding to the inclined axis in the triangle made up of the inclination angle. Specify the length of the actual axis of the inclined axis in the triangle made up of the inclination angle.

Setting range (unit) 9999.999

9999.999

Use an upper limit value at the feedrate indicated 1 to 999999 (mm/min) when validating external deceleration signals. This parameter is valid when #1239 set11/bit6 is set to 0.

II - 54

5.

BASE SPECIFICATIONS PARAMETERS

(SETUP PARAM 1. 8/15) # 1217 aux01 1218 aux02 (bit3) aux02 (bit4) Items Details Not used Parameter Specify a parameter input/output format. input/output 0: Type I format 1: Type II (related to #1218 aux02/bit5) Tool number Specify the R register that contains the tool number selection used for automatic calculation when measuring the coordinate offset of an external workpiece. 0: Conforms to #1130 set_t. 1: Uses the tool number indicated by user PLC Parameter I/O Specify the spindle specification address of parameter II spindle I/O type II. specification 0: C address 1: T This parameter also applies to the spindle specification address for input and collation. Note: This parameter is valid only for parameter I/O type II (bit 3 of aux02 in #1218 is 1). Set No. valid Specify which program No. is selected when inputting operation using #1 MAIN PROGRAM in Data I/O when program input screen. 0: The No. in the input data is valid. 1: The No. set in the data setting area is valid. Input by (1) When inputting operation using #1 MAIN PROGRAM in Data I/O screen, select one of the program overwrite following options when the input program has already been registered: 0: An operation error (E65) occurs. 1: Input by overwrite. (2) When using the high-speed program server, select the operation if the name of the file to be transmitted with transmission (IC host) operations already exists in the host. 0: Overwrite prohibit 1: Overwrite valid Stop highSet 1 to disable the function that stops the system when speed PC the high-speed processing time is extended. monitoring Disable the monitoring function only as a temporary function measure. Improve skip 0: Skip accuracy (conventional specification) coordinate 1: Changes skip accuracy (correct a position in skip accuracy coordinates when entering skip signals). Dog-type Select whether to move to the intermediate point during intermediate automatic dog-type reference point return. point 0: Do not move to intermediate point during dog-type reference point return. 1: Move to intermediate point during dog-type reference point return. Setting range (unit) 0/1

0/1

aux02 (bit5)

0/1

aux02 (bit6)

0/1

aux02 (bit7)

0/1

1219 aux03 (bit1)

0/1

aux03 (bit2) aux03 (bit5)

0/1

0/1

II - 55

5.

BASE SPECIFICATIONS PARAMETERS

# 1220 aux04 (bit 0) (For L system only)

Items Details Tool life check Specify the life check standard applicable when the timing use count is incremented in tool life management II. selection 0: Determine that the tool life is over when the incremented use count exceeds the life count. (Use count > life count)

Setting range (unit) 0/1 (Default: 0)

aux04 (bit1)

aux04 (bit2) aux04 (bit3) aux04 (bit4)

1: Determine that the tool life is over when the incremented use count has reached the life count. (Use count life count) Validity of Validate or invalidate the space code described in the 0/1 space code in comment statements in the machining program in edit comment operation with the special display. (Default: 0) 0: Invalidate the space code in the comment statements of the machining program. 1: Validate the space code in the comment statements of the machining program. Not used. Not used. Data input/ output unit selection Specify the input/output data unit for tool data and user 0/1 parameter input/output. 0: Internal unit (metric) 1: Follows command mode set with #1152 I_G20 Metric when set to 0 Inch when #1152 I_G20 is set to 1 This parameter is valid when initial metric (#1041 I_inch 0) is set and the setting and display unit is the command unit (#1226 aux10 bit6 1). In all other cases, the tool data will be input and output with the internal units.

II - 56

5.

BASE SPECIFICATIONS PARAMETERS

# 1221 aux05 (bit7)

Items Details Setting range (unit) Current value B Select the type of counter to be displayed on the 0/1 valid POSITION screen. 0: Displays a relative value (value that includes tool length offset amount, tool radius compensation amount and workpiece coordinate offset amount) 1: Displays current value B (value that does not include tool length offset amount, tool radius compensation amount and workpiece coordinate offset amount)

aux05/bit7 = 1 aux05/bit7 = 0 Tool offset Workpiece offset

(Note1) When #1221 aux05/bit7 is set to 1, the current value B is selected regardless of the bit type of #1287 ext23. When the current value B is valid, the counter zero or origin zero is invalid. (Note2) The following limits apply to M64A/M64: This is compatible only with the lathe system. The relative value counter on the COORDINATE screen will also display the current value B. When #1287 ext23/bit3 is set to 0, the relative value will be displayed instead of the current value B regardless of this parameter setting. 0: Display no confirmation message when tool 0/1 compensation data is set. 1: Display a confirmation message when tool compensation data is set. (Applicable only to M64 D version series) When 1 is set in this parameter, the axis specified by 0/1 base specification parameter #1028 base_k is measured and no other axes are measured if they move. (Applicable only to M64 D version series)

1222 aux06 (bit0)

aux06 (bit1)

Validity of tool length measurement confirmation message Height axis specification

II - 57

5.

BASE SPECIFICATIONS PARAMETERS

Items aux06 Servo (bit2) waveform display aux06 Enable/disable (bit3) setup parameter lock aux06 Minimum cut-in (bit4) amount selection

aux06 Fixed cycle (bit5) for compound lath command format check selection aux06 Zero point return (bit7) deceleration check method

1223 aux07 Rapid traverse (bit0) inclination constant multi-stage acceleration and deceleration

aux07 Deceleration (bit1) check method 2

Details Specify whether to enable the waveform display function. (Applicable only to M64 D version series) 0: Disable the waveform display function. 1: Enable the waveform display function. Specify whether to enable the setup parameter lock function. 0: Disable 1: Enable Select the minimum cut-in amount command value for the compound thread cutting cycle (G76 command). 0: The minimum cut-in amount (Q) is 0. 1: The minimum cut-in amount (Q) is the CNC internal data. Select the operation to be made if the 1st block of the fixed cycle for compound lathe is omitted when the conventional format is selected (#1265 ext01/bit0 0). 0: Program error (P33) occurs. 1: Parameter setting value is used. Set the deceleration check method used during automatic reference point return. (Applicable only to M64 D version series) 0: In-position check 1: Commanded deceleration check Specify whether to enable the rapid traverse inclination constant multi-stage acceleration/deceleration function. (Applicable only to M64 D version series) 0: Disable 1: Enable Related parameters: #2064 rapid2 Speed 2 #2065 G0tL2 Time constant 2 #2066 rapid3 Speed 3 #2067 G0tL3 Time constant 3 Select the deceleration check method in G1+G9. 0: Command deceleration check in G1+G9 1: In-position check in G1+G9 The deceleration check is not performed except G1+G9. When #1306 InpsTyp deceleration check specification type is set to 1 (Deceleration check specification type 2), this parameter will be invalid.

Setting range (unit) 0/1

0/1

0/1

0/1

0/1

0/1

0/1

II - 58

5.

BASE SPECIFICATIONS PARAMETERS

# aux07 (bit2)

Items Synchronous tap R-point in-position check

Details

aux07 (bit3)

Synchronous tap in-position check improvement

0: Disable the synchronous tap I-point R-point in-position check. 1: Enable the synchronous tap I-point R-point in-position check. (Applicable only to M64 D version series) Note: This parameter is valid only when 1 (in-position check is valid) is set in bit 3 of #1223 aux07 (synchronous tap in-position check improvement). Specify whether to enable the synchronous tap 0/1 in-position check improvement function. (Applicable only to M64 D version series) 0: Disable 1: Enable

Setting range (unit) 0/1

aux07 (bit4)

aux07 (bit5)

aux07 (bit6)

aux07 (bit7)

1224 aux08 (bit0)

Related parameters: #1223 bit 2 Synchronous tap R-point in-position check bit 4 Synchronous tap hole bottom in-position check bit 5 Synchronous tap R-point in-position check 2 Synchronous 0: Disable the synchronous tap hole bottom tap hole bottom in-position check. in-position 1: Enable the synchronous tap hole bottom check in-position check. (Applicable only to M64 D version series) Note: This parameter is valid only when 1 (in-position check is valid) is set in bit 3 of #1223 aux07 (synchronous tap in-position check improvement). Synchronous 0: Disable synchronous tape R-point in-position tap R-point check. in-position 1: Enable synchronous tape R-point in-position check. check 2 (Applicable only to M64 D version series) Note: This parameter is valid only when 1 (in-position check is valid) is set in bit 3 of #1223 aux07 (synchronous tap in-position check improvement). Cancel 0: Retains a spindle rotation speed (, S) when synchronous performing synchronous tap return. tap (,S) return 1: Cancels a spindle rotation speed (, S) by return with G80. Synchronous Specify a synchronous tap method. tap method 0: Synchronous tap (multi-step acceleration and deceleration and rapid return) 1: Conventional type synchronous tap Sampling data Set the validity of the sampling data output. output 0: Sampling output invalid 1: Sampling output valid

0/1

0/1

0/1

0/1

0/1

II - 59

5.

BASE SPECIFICATIONS PARAMETERS

# 1225 aux09 (bit0)

aux09 (bit7)

Items PLC Interface Diagnosis screen changeover Enable/disable spindle rotation speed clamp

1226 aux10 (bit0)

aux10 (bit1)

Tool compensation data for external workpiece coordinate offset measurement Optional block skip type

Details Set this to change to the PLC Interface Diagnosis screen. 0: 40-character compatible screen 1: 80-character compatible screen Specify whether to enable spindle rotation speed clamp by the spindle rotation speed clamp command (G92S, Q) instead of the spindle rotation speed command (R108) specified by the user ladder. 0: Enable 1: Disable Select the tool offset data to be used for external workpiece coordinate offset measurement. 0: Tool length data and tool nose wear data 1: Tool length data

Setting range (unit) 0/1

0/1

0/1

aux10 (bit2)

aux10 (bit3)

aux10 (bit4)

Specify whether to enable optional block skipping in the middle of a block. 0: Enable block skipping only at the beginning of a block. 1: Enable block skipping at the beginning of the block and in the middle of a block. Single block Specify the time at which the single block signal is stop timing activated. 0: When the signal goes ON while automatic operation is starting, the block stops after it is finished. 1: When the signal is ON at the end of the block, the block stops. C-axis Specify the C-axis reference point return type. reference point 0: Origin return is performed by the G28 reference return type point return command or when manual reference point return is activated. The origin dog is used. 1: When the first C-axis command is issued after the C-axis mode is entered in automatic mode, reference point return is performed before execution of the block. Also, reference return is performed by the G28 reference point return command or when manual reference point return is activated. The Z phase of the encoder is used. S command Specify whether to output a strobe signal when the S during constant command is issued in constant surface speed mode. surface speed 0: Output no strobe signal in constant surface speed mode. 1: Output strobe signals in constant surface speed mode.

0/1

0/1

0/1

0/1

II - 60

5.

BASE SPECIFICATIONS PARAMETERS

# aux10 (bit5)

Items Arbitrary allocation of dog signal

aux10 (bit6)

aux10 (bit7)

1227 aux11 (bit0)

aux11 (bit1)

Details Specify whether to enable the arbitrary allocation parameter for the origin dog and H/W OT. 0: Disable arbitrary allocation. (Fixed device) 1: Enable arbitrary allocation. (Device specified by the parameter) Setup and Specify the unit to be used as the setup/display unit or display unit handle feed unit, the command unit or internal unit. The machining program variables (system variables for coordinate system) are changed simultaneously. 0: Internal unit 1: Unit specified by command Note 1: This parameter is valid only in initial millimeter mode (0 is set in 14041 I_inch). The internal unit is always used in initial inch mode (1 is set in 14041 I_inch). Note 2: This parameter is validated immediately after it is set. Note 3: If addition setting is performed for tool and workpiece offset data with the command unit being inch and internal unit being mm, an error may be generated. Note 4: If 1 is set for this parameter and two systems are used, the operation will follow the unit commanded for each system. Note 5: The internal data is an internal unit determined with #1041 I_inch. Note 6: This parameter is not related to the PLC axis. Related parameter: #1152 I_G20 (Initial command unit) Shorten JOG Specify whether to shorten the JOG stop time. stop time 0: Do not shorten the JOG stop time. (Same as before) 1: Shorten the JOG stop time. Select PLC Set up this option when disabling the cutting start signal or interlock by spindle feedrate attained. spindle 0: Cutting start interlock by PLC signal feedrate 1: Cutting start interlock by spindle feedrate attained attained Select H or D Set up this option to validate the data that is set up on code the tool life management screen when issuing the H99 or D99 command. 0: The H and D codes validate the data that is set up on the management setup screen. 1: Validates the data that is set up on the management setup screen when issuing the H99 or D99 command.

Setting range (unit) 0/1

0/1

0/1

0/1

0/1

II - 61

5.

BASE SPECIFICATIONS PARAMETERS

# aux11 (bit2)

aux11 (bit3)

aux11 (bit4)

aux11 (bit5)

aux11 (bit6)

Items Details Measures Select a condition where a relieving operation against tool completes after measurement with tools. setter chattering 0: Sensor signals has stopped for 500 ms or longer. 1: 100 s or longer has passed after sensor signals stopped. Absolute Select whether to display a tool nose position or coordinate coordinate value with the absolute coordinate switching (nose counter. R) 0: Displays the tool nose position. [Special display 1: Displays the position specified by program unit compatible] command. Program Specify whether to simply check the program address check address when the machining program is executed. 0: Don't check the program address. 1: Check the program address. Spindle rotation Specify whether to clamp the rotation in constant speed clamp surface speed mode when the spindle rotation speed clamp command is issued. 0: Clamp the rotation regardless of the constant surface speed mode. 1: Clamp the rotation only in constant surface speed mode. Word edit menu Select the word edit menu format. Set 0 in this parameter to select the following menu format:
LOOK UP DELETE REPLACE COPY
SEARCH

Setting range (unit) 0/1

0/1

0/1

0/1

0/1

INSERT
PROGRAM

MENU MENU

B.G. SRH B.G. END COMMENT RETURN

WORD WORD

STR

STR

RETURN

Set 1 in this parameter to select the following men

COPY LOOK UP DELETE REPLACE
SEARCH PROGRAM MENU MENU

INSERT

B.G. SRH B.G. END COMMENT RETURN

WORD WORD

STR

STR

RETURN

II - 62

5.

BASE SPECIFICATIONS PARAMETERS

# aux11 (bit7)

1228 aux12 (bit0)

aux12 (bit1)

aux12 (bit2)

aux12 (bit3)

aux12 (bit4)

aux12 (bit5) aux12 (bit6)

Items Details Switch the set up the range of tool life data to be input or range of tool life compared. 0: Inputs or compares all of the data output. data to be input 1: Inputs or compares part of the data output (For M system 1) Tool life management I data to be input or only) compared tool number (D), lifetime (E), life count (F), and auxiliary data (B). 2) Tool life management II data to be input or compared Group number (G), method (M), life (E/F), tool number (D), and compensation number (H) Note: When the maintenance function data input/ output #(99) ( ) is set, all data will be input and compared. Switch Set up this option to switch the coordinate value coordinate value screen. screen 0: 80-character screen 1: 40-character screen Switch offset Set up this option to switch the offset and parameter and parameter screen to the parameter screen. screen 0: Displays the offset and parameter screen. 1: Displays the parameter screen. Switch data Set up the range of data protection in data protection in transmission mode. data 0: Protects both send and receive data. transmission 1: Protects receive data only. mode Nose R Select whether to specify the nose R compensation specification by shape or wear number. 0: Specifies the nose R compensation by shape number. 1: Specifies the nose R compensation by wear number. Select operation Specify both block cutting start interlock and cutting start interlock as the operation error or stop code. error or stop code 0: Operation error 1: Stop code Select constant Select constant surface speed coordinates. surface speed 0: Workpiece coordinate value coordinates 1: Absolute coordinate value Switch relative Select whether to preset the relative coordinates with values displayed workpiece coordinate preset (G92.1) or counter preset (G92). 0: Preset relative coordinates. 1: Do not preset relative coordinates.

Setting range (unit) 0/1

0/1

0/1

0/1

0/1

0/1

0/1

0/1

II - 63

5.

BASE SPECIFICATIONS PARAMETERS

# aux12 (bit7)

Items Protection with manual value command

1229 set01 (bit0) set01 (bit1)

Subprogram interrupt Accurate thread cutting E

set01 (bit2)

Radius compensation type B (For M system only)

set01 (bit2)

Nose R compensation type B (For L system only)

set01 (bit3)

Initial constant surface speed

set01 (bit4)

Synchronous tap

set01 (bit5)

Start point alarm

Details Set up this option to protect a manual value command. 0: Does not protect the manual value command (same as before). 1: Protects the manual value command. 0: Specifies the user macro interrupt of macro type. 1: Specifies the user macro interrupt of sub-program type. 0: Address E specifies the number of threads per inch for inch screw cutting. 1: Address E specifies precise reading for inch screw cutting. 0: When the start-up and cancel commands are operated during radius compensation, their blocks are not handled by intersection operation processing; they are handled as offset vectors in the direction vertical to that of the commands. 1: When the start-up and cancel commands are operated during radius compensation, the intersection operation processing of the command block and the next block is executed. 0: When the start-up and cancel commands are operated during nose R and radius compensation, their blocks are not handled by intersection operation processing; they are handled as offset vectors in the direction vertical to that of the commands. 1: When the start-up and cancel commands are operated during nose R and radius compensation, the intersection operation processing of the command block and the next block is executed. 0: The initial state after power-ON is a constant surface speed control cancel mode. 1: The initial state after power-ON is a constant surface speed control mode. 0: Handles the G74 and G84 tap cycles as the tap cycles with a floating tap chuck. 1: Handles the G74 and G84 tap cycles as the tap cycles without a floating tap chuck. Select an operation when the operation start point cannot be found while moving the next block of G117. 0: Enables an auxiliary function after the block has been moved. 1: Outputs an program error (P33) when the operation start point is not found.

Setting range (unit) 0/1

0/1

0/1

0/1

0/1

0/1

0/1

0/1

II - 64

5.

BASE SPECIFICATIONS PARAMETERS

# set01 (bit6)

Items Grid display selection

1230 set02 1231 set03 (bit1)

Switch graphic coordinates

set03 (bit2)

Switch graphic check trace

set03 (bit3)

Hold display range information

set03 (bit4)

Switch zero point mark display position

1232 set04 (bit0)

Switch load monitor

set04 (bit1)

Program format (IC card)

Details Select a grid type to be displayed on the servo monitor screen during dog type reference point return. 0: Selects the distance between dog OFF and zero point (including a grid mask amount). 1: Selects a value given by reducing a grid mask amount from the distance between dog OFF and zero point. Not used. Select whether to draw graphics with the machine coordinate value or the tool position coordinate value (position being machined, obtained by subtracting the tool compensation amount from machine coordinate values) when displaying the trace function. 0: Machine coordinate value (same as conventional method) 1: Tool position coordinate value The counter display and counter name are sequenced with this. Select whether to draw both the machine coordinate value (tool center path) and tool position coordinate value (program path) or draw only the coordinates selected with switch graphic coordinates (#1231 set03/ bit1) when using the program check function. 0: Both machine coordinates and tool position coordinates (same as conventional method) 1: Only coordinates designated with switch graphic coordinates. Select whether to hold the display range information (drawing position and scale value) for graphic displays. 0: Hold. 1: Do not hold. (Initialize each time ... same as conventional method) Select the position for displaying the zero point mark in the graphic display. 0: Machine coordinate zero point (same as conventional method) 1: Workpiece coordinate zero point Select whether to detect the load with the load monitor's load detection, excluding during acceleration/ deceleration. 0: Detect also during acceleration/deceleration. (Conventional) 1: Do not detect during acceleration/deceleration. Select the format of the file output during copying (NC IC). 0: Add % to the head of the file. 1: The head of the file is No. 0.

Setting range (unit) 0/1

0/1

0/1

0/1

0/1

0/1

0/1

II - 65

5.

BASE SPECIFICATIONS PARAMETERS

# 1233 set05 (bit1)

Items Spindle clamp selection

1234 set06 (bit6) set06 (bit7) 1235 set07 (bit0) set07 (bit1)

Details Select whether to validate the spindle override for the spindle speed clamp command (G92 S?). 0: Spindle override invalid 1: Spindle override valid Not used.

Setting range (unit) 0/1

0/1 0/1

Enable/disable MELDASNET

set07 (bit2)

1236 set08 (bit0) set08 (bit1)

set08 (bit2)

set08 (bit7) 1237 set09 (PR) (bit0)

Enable or disable the MELDASNET function. 0: Enable 1: Disable Helical 0: Select normal speed designation also for 3rd interpolation axis speed 2 1: Select arc plane element speed designation File server 0: Set upper limit of program file size to 2 selection for gigabytes. version upgrade 1: Set upper limit of program file size to 16 megabytes. Fixed type When the fixed type compensation value is chopping selected, the method is changed to the compensacompensation value sequential update type after the tion valid only at first four cycles. start 0: Method changeover invalid 1: Method changeover valid Manual rotation Select the unit of manual rotation axis feedrate. axis feedrate unit 0: Fixed to [/min] 1: Same speed as before Spindle speed Select the pulse input source of actual spindle detection rotation speed output (R18/19) when spindle encoder serial connection (#3025 enc-on: 2) is selected. 0: Serial input 1: Encoder input connector Current limit Set whether to cancel the position droop when the droop cancel current limit changeover signal is canceled. invalid 0: Cancel droop. 1: Do not cancel droop. Not used.

0/1 (MAGIC64) 0/1 (MAGIC64)

0/1

0/1

0/1

0/1

0/1

External Set up this function to use the external workpiece 0/1 workpiece offset coordinates by shifting them to the Z axis. 0: Does not reverse the sign of external workpiece offsets (Z shift) (same as before). 1: Reverses the sign of external workpiece offsets (Z shift). Note: When the sign of external workpiece offsets (Z shift) has been reversed, do not measure those external workpiece offsets. However, the external workpiece offsets can be measured by tool pre-setter.

II - 66

5.

BASE SPECIFICATIONS PARAMETERS

# set09 (bit1)

set09 (bit2)

set09 (bit3)

set09 (bit4)

set09 (bit5)

1238 set10 (PR) (bit0)

set10 (bit6)

Details The feedrate display for the special display unit is changed. 0: Display as feed per minute. 1: Change between feed per minute and feed per rotation according to the modal state. Switch PC I/F T The T command display for the special display unit is modal changed. (Only L system) 0: Display tool No. (excluding low-order two digits). 1: Display including the compensation No. Switch PC I/F The dwell time display for the special display unit is remaining changed. distance dwell 0: Display at feedrate display position. time display 1: Display at remaining distance display position. Switch PC I/F The display of the program being executed for the execution special display unit is displayed. program display/ 0: Display as searched state, regardless of comment operation mode. display 1: If operation mode and searched program differ, program is not displayed. Comment is displayed for head block search. Switch PC I/F This parameter is for the special display unit I/F. modal S 0: The S command commanded last is returned. 1: When #1039 spinno is 1 The 1st spindle data is returned. When #1039 spinno is 2 If #1199 Sselect for 2nd system is set to 1 with 2nd system setting, the 2nd spindle data is returned. When another command is issued, the 1st spindle data is returned. Note: When using constant surface speed control (G96 modal), the actual rotation speed command is returned. Switch G36 If a G code system containing the G36 (automatic function tool length measurement X) function is selected, select whether to use G36 for the automatic tool length measurement or arc thread cutting (CCW) function. 0: Automatic tool length measurement 1: Arc thread cutting (CCW) Not used.

Items Switch PC I/F F modal

Setting range (unit) 0/1

0/1

0/1

0/1

0/1

0/1

0/1

II - 67

5.

BASE SPECIFICATIONS PARAMETERS

# set10 (bit7)

1239 set11 (PR) (bit0) set11 (bit1) set11 (bit2) set11 (bit3)

Items Details Switch operation Select whether to validate the NC alarm 5 (AL5) alarm signal output. 0: NC alarm 5 (AL5) invalid All operation alarms are output to NC alarm 4 (AL4). All operation alarms are recorded in the alarm history. 1: NC alarm 5 (AL5) valid The following operation alarms are not output to NC alarm 4 (AL4). These are output to NC alarm 5 (AL5). The operation alarms output to NC alarm 5 (AL5) are not recorded in the alarm history. External interlock axis found Cutting override zero External feedrate zero Block start interlock Cutting block start interlock Cutting interlock for spindle-spindle polygon (G51.2) Coil switching 0: Via PLC. (Y2D7) method 1: NC internal processing. (Y2D7 is invalid.) Not used. Not used. Polygon Select whether to cancel the polygon machining machining mode mode when reset is applied. at reset 0: Do not cancel. 1: Cancel. Invalidate G51.1 Select whether to carry out phase control with the phase command spindle-spindle polygon function. 0: Always validate phase control. * When R is not commanded, it is handled as R0. 1: Validate phase control only at R command Door interlock Select whether to validate the spindle clamp speed spindle speed changeover function by the PLC signal. clamp valid 0: Invalid 1: Valid External Designate the method for setting the external deceleration axis deceleration speed. compliance valid 0: Set speed common for all axes (#1216 extdcc external deceleration speed) 1: Set speed for each axis (#2086 exdcax external deceleration speed)

Setting range (unit) 0/1 (Default: 0)

0/1 0/1 0/1 0/1

set11 (bit4)

0/1

set11 (bit5)

0/1

set11 (bit6)

0/1

II - 68

5.

BASE SPECIFICATIONS PARAMETERS

# set11 (bit7)

1240 set12 (PR) (bit0) set12 (bit1)

Items APLC software working environment setting Handle input pulse Megatorque motor handle feed magnification

Details 0: Run the APLC software with the ROM. 1: Run the APLC software with the RAM.

Setting range (unit) 0/1

Select the handle input pulse. 0: MELDAS standard handle pulse 1: Handle 400 pulse Select the magnification of megatorque motor handle 1 pulse. 0: Double the handle 1 pulse magnification specified by the handle feed magnification signal (Y2C0 to Y2C2). 1: Use the handle 1 pulse magnification specified by the handle feed magnification signal (Y2C0 to Y2C2) as is. When 0.1m is set, the #2027 G28sft reference point shift amount is multiplied by ten.

0/1

0/1

set12 (bit2)

Zero point shift amount 10-fold at 0.1m

0/1

II - 69

5.

BASE SPECIFICATIONS PARAMETERS

(SETUP PARAM 1. 9/15) # 1265 ext01 (PR) (bit0) Items Command format 1 Details Select the command format for the fixed cycle for compound lathe. 0: Conventional format 1: MELDAS special format (1 block command method) Select the command format for the lathe fixed cycle. 0: Conventional format 1: MELDAS special format Select the command format for the hole drilling fixed cycle. 0: Conventional format 1: MELDAS special format Not used. Select the high-speed high-accuracy G code type. 0: Conventional format 1: F format Not used. Not used. Handle C axis Specify whether the rotary axis coordinate before 0/1 coordinate the cylindrical interpolation start command is issued during cylindrical is kept during the cylindrical interpolation or not. interpolation 0: Do not keep 1: keep Mirror image Select the type of mirror image operation. 0/1 operation (Applicable only to M65 and M66) (Default: 0) 0: Type 1 - The program mirror image, external mirror image, and parameter mirror image are exclusive to each other. - An increment command moves the image to the position indicated by the move amount with the sign inverted. 1: Type 2 - Mirror image operation is enabled when the program mirror image (G51.1) command is issued or when the external signal or parameter is ON. - An increment command moves the image to the position determined by applying the mirror image to the absolute program coordinates. Setting range (unit) 0/1

ext01 (bit1) ext01 (bit2)

Command format 2 Command format 3

0/1

0/1

1266 ext02 (PR) 1267 ext03 (PR) (bit0) 1268 (PR) 1269 (PR) 1270 (PR) ext04 ext05 ext06 (bit7)

G code type

0/1

1271 ext07 (PR) (bit0)

II - 70

5.

BASE SPECIFICATIONS PARAMETERS

# ext07 (bit1)

Items Address specifying fixed cycle repetition count (For M system only)

ext07 (bit2)

ext07 (bit3)

ext07 (bit4)

ext07 (bit5)

Details Specify the address that specifies the fixed cycle repetition count. (Applicable only to M65 and M66) 0: Address L only 1: Addresses K and L If addresses K and L are specified simultaneously, the data at address K is used for operation. F-command unit Specify the unit to be used if a thread cutting read command contains on decimal point. (Applicable only to M65 and M66) 0: Type 1 (conventional specifications) F1 1 mm/rev, 1 inch/rev 1: Type 2 F1 0.01 mm/rev, 0.0001 inch/rev G-code group for Specify the G-code group for unidirectional unidirectional positioning. (Applicable only to M65 and M66) positioning (for 0: Unmodal G code (group 00) M system only) 1: Modal G code (group 01) Related parameter: #8209 G60 SHIFT (Set the last positioning direction and distance for each axis applicable when the unidirectional positioning command is issued.) Operation by Specify the mode of canceling radius compensation vector by the independent G40 command. independent G40 command (Applicable only to M65 and M66) (Default: 0) 0: Type 1 (conventional specifications) The independent G40 command cancels the radius compensation vector. 1: Type 2 The radius compensation vector is not canceled by the independent G40 command but is canceled by the next move command for the radius compensation plane. Cut start position Specify the position from where cutting begins in a (For L system fixed cycle for compound lathe. only) 0: Conventional specifications The cut start position is determined by the final shaping program. 1: Extended specifications The cut start position is determined from the cycle start point.

Setting range (unit) 0/1 (Default: 0)

0/1 (Default: 0)

0/1

0/1 (Default: 0)

0/1 (Default: 0)

II - 71

5.

BASE SPECIFICATIONS PARAMETERS

# ext07 (bit6)

ext07 (bit7)

1272 ext08 (PR) (bit0)

ext08 (bit1)

ext08 (bit2)

ext08 (bit3)

Details Specify whether to apply nose R compensation to shapes in a rough cutting cycle. 0: Conventional specifications If nose R compensation is enabled for the final shaping program, the shape obtained after applying nose R compensation to the final shaping program is used as the rough cutting shape. 1: Extended specifications The shape made by the final shaping program, without nose R compensation, is used as the rough cutting shape. Cut amount (For Specify the operation to be performed when the L system only) program-specified cut amount exceeds the cut amount of the final shaping program. 0: Conventional specifications A program error occurs if the program-specified cut amount exceeds the cut amount of the final shaping program. 1: Extended specifications Rough cutting is performed by one cut if the program-specified cut amount exceeds the cut amount of the final shaping program. Switch pocket 0: Conventional specifications Pocket machining is selected with the H machining operation designation. The pull direction when pocket machining is ON is the Z direction. 1: Extended specifications If there is an X and Z axis in the first movement block after the finished shape start block is started, pocket machining will start. The pull direction when pocket machining is ON is the X direction. M function Specify whether to enable the M function synchronous tap synchronous tap cycle. cycle 0: Invalid 1: Valid Spiral/conical Select the command format for spiral interpolation interpolation and conical interpolation. command format 0: Type 1 (conventional specifications) 2 1: Type 2 (spiral speed L designation, increment designation) Switch macro Select whether to shift the argument to the call function subprogram if nests are overlapped when per block call (G66.1) is commanded. 0: Shift argument even if nests are overlapped. 1: Do not shift arguments if nests differ. (Conventional specifications)

Items Nose R compensation (For L system only)

Setting range (unit) 0/1 (Default: 0)

0/1 (Default: 0)

0/1

0/1

0/1

II - 72

5.

BASE SPECIFICATIONS PARAMETERS

# ext08 (bit4) ext08 (bit5)

ext08 (bit6)

ext08 (bit7)

1273 ext09 (PR) (bit0) ext09 (bit1)

ext09 (bit2)

ext09 (bit3)

ext09 (bit4)

Select the tap cycle. 0: Pecking tap cycle 1: Deep hole tap cycle Deep hole tap Select whether to validate override on the pulling cycle override operation during synchronized tapping with the deep selection hole tap cycle. 0: Invalid 1: Valid Switch corner The corner chamfering/corner R command format is chamfering/ extended. corner R 0: Command format I (conventional format) command Issue a command with comma (,C and ,R). format 1: Command format II In addition to command format I, commands can be issued with an address that does not have a comma. Corner chamfering: I/K or C, corner R: R Return position Select the destination to return to after a macro after macro interrupt in the fixed cycle. interrupt in fixed 0: Return to block in fixed cycle. cycle selection 1: Return to block after fixed cycle. Switch ASIN Select the ASIN calculation results range. calculation 0: 90 to 90 results range 1: 90 to 270 Switch system Select the unit for the system variable #3002 (time variable unit during automatic start). 0: 1ms unit 1: 1 hour unit Switch G71, Select whether to determine the cutting direction G72, G73 cutting with the finished shape, or according to the direction commanded finishing allowance and cutting judgment allowance when the longitudinal rough cutting cycle (G71), face rough cutting cycle (G72) or closed loop cutting cycle (G73) is commanded. 0: Conventional specifications Determined according to the finished shape program. 1: Extended specifications Determined according to the finishing allowance and cutting allowance commanded in the program. Facing turret Select the coordinate values of the axis for which mirror image facing turret mirror image is valid. coordinate value 0: Move axis in same direction as machine type value. 1: Move axis in direction opposite machine value. Facing turret Select the axis for which facing turret mirror image is mirror image valid. valid axis 0: Fixed to 1st axis. selection 1: Determined according to plane selected when facing turret mirror image is commanded.

Items Tap cycle selection

Details

Setting range (unit) 0/1

0/1

0/1

0/1

0/1

0/1

0/1

0/1

0/1

II - 73

5.

BASE SPECIFICATIONS PARAMETERS

# 1274 ext10 (PR) (bit7)

Items Word range check

1275 (PR) 1276 (PR) 1277 (PR)

ext11 ext12 ext13 (bit0) Tool life management II count type 2

Details Setting range (unit) Select whether to check that the operation 0/1 expression of the word date in the program is enclosed in brackets ( [ ] ) when the machine program is executed. This check is also applied to the 08000 to 09999 and the machine manufacture macro program. 0: Check valid 1: Check invalid Not used. Not used.

1278 ext14 (PR) (bit0) 1279 ext15 (PR) (bit0)

Specify how and when the mount or use count is incremented in tool life management II. 0: Type 1 The count is incremented when the spindle is used for cutting. 1: Type 2 The count is incremented for the tool used or mounted for one program. The increment is enabled by resetting. Program restart Select the program restart method. method selection 0: Conventional format 1: F format System Select the system synchronization method. synchroniza0: If one system is not in automatic operation, tion method ignore the synchronization command and execute the next block. 1: Operate according to the synchronization ignore signal. If the synchronization ignore signal is set to 1, the synchronization command will be ignored. When set to 0, synchronization will be applied.

0/1 (Default: 0)

0/1

0/1

II - 74

5.

BASE SPECIFICATIONS PARAMETERS

# 1280 ext16 (PR) (bit0)

Items I/F per axis during cross machining control

Details Setting range (unit) 0/1 Set the handling of the following PLC I/F for axes interchanged with cross machining control. Mirror image Manual/automatic interlock Manual/automatic machine lock 0: Follows axis configuration before cross machining control. 1: Follows axis configuration after cross machining control. (Example) Set as follows for the automatic interlock (+) device for X1 when carrying out cross machining with the 1st axis (X1) in the 1st system and 1st axis (X2) in the 2nd system. Setting value 0: Y1A8 (I/F for 1st axis in 1st system) Setting value 1: W28 (I/F for 1st axis in 2nd system) Note: If the number of axes in the system changes with cross machining, the I/F of the target axis may change when this parameter is set to 1. (Example) When 1st system's C axis is moved to 2nd system with a 1st system (X, Z, C, Y) and 2nd system (X, Z) configuration: When setting value is 1: W2A, W12 and W4A, etc., will be the I/F for the C axis moved to the 2nd system. However, Y192, Y1AA and Y1CA, etc., will change to the I/F of the Y axis in the 1st system because the axes following the removed C axis (third place) are shifted up.

II - 75

5.

BASE SPECIFICATIONS PARAMETERS

# 1280 ext16 (PR) (bit1)

Items Cross machining control cancel with reset

ext16 (bit2)

ext16 (bit3)

Details Select whether to cancel the cross machining control when reset is applied. 0: Cancel cross machining control with reset. 1: Do not cancel cross machining control with reset Interchange Set whether to interchange (or move) the coordinate coordinate value values when displaying. display This setting will be followed when the axes are interchanged and when the axes are moved. 0: Interchange (or move) coordinate values with cross machining control, and display. 1: Display coordinate values for cross machining control without interchanging (or moving). (Example) When 1st system's C axis is moved to 2nd system with a 1st system (X, Z, C, Y) and 2nd system (X, Z) configuration: 1st system: X, Z and Y coordinate values are displayed. 2nd system: X, Z and C coordinate values are displayed. Reset operation Select whether to cancel synchronization/ for synchroniza- superimposition control with resetting. tion/super0: Cancel. imposition 1: Do not cancel. control

Setting range (unit) 0/1

0/1

0/1

II - 76

5.

BASE SPECIFICATIONS PARAMETERS

# 1281 ext17 (PR) (bit0)

Items Zero point return operation changeover parameter

ext17 (bit1) 1282 ext18 (PR) 1283 ext19 (PR) 1284 ext20 (PR)

Tool offset addition axis selection

Details Setting range (unit) (Zero point setting operation) 0/1 The Operation error 1036 will occur regardless of this parameter, and regardless of manual or automatic operation. (High-speed zero point return) 0: <During manual operation> The master axis and slave axis will simultaneously start zero point return. Even if one of the axes reaches the zero point, the other axis will continue to move until it reaches the zero point. Thus, if the difference of the master axis and slave axis feedback position before zero point return is larger than the tolerable synchronization error amount, the error Operation error 0051 will occur during zero point return. <During automatic operation> The master axis and slave axis will simultaneously start zero point return. When the master axis reaches the zero point, the slave axis will stop. Thus, the positional relation of the master axis and slave axis established before zero point return is maintained. 1: <During manual operation> <During automatic operation> The master axis and slave axis will simultaneously start zero point return. When the master axis reaches the zero point, the slave axis will stop. Thus, the positional relation of the master axis and slave axis established before zero point return is maintained. 0: Follows Tchg34 0/1 1: Plane selection Base J setting name is set as the 3rd axis compensation axis. Not used. Not used. Not used.

II - 77

5.

BASE SPECIFICATIONS PARAMETERS

# 1285 ext21 (PR) (bit0)

Items Multi-system program generation and operation

ext21 (bit1)

1286 ext22 (PR) (bit0)

ext22 (bit1)

1287 ext23 (PR) (bit0)

ext23 (bit3)

Details 0: When a machining program is newly registered, it is registered as a program for the selected system. 1: When a program is newly registered, a system common program No. is generated unconditionally. If there are no contents in the subprogram when a subprogram is called during automatic operation, the program will be searched for and executed from $1. Changeover of 0: Select the program in the selected system method to select with operation search. operation 1: Select a common system program with program operation search. (A common system program No. will be selected.) Program 0: Only the programs in the selected system are input/output input/output. method selection 1: The designated programs are output for all systems. The systems are delimited with the $ mark. The programs delimited with the $ mark are assigned and input into each system. (If the program does not have a $ mark, it will be handled as system 1.) Tool data 0: The tool data is input/output in a batch for all systems. input/output method selection 1: Only the tool data for the selected system is input/output with the system selection switch. Workpiece Select the mode of displaying the workpiece coordinate counter. coordinate display 0: Dont update the display immediately after workpiece coordinate data is changed. 1: Update the display immediately after workpiece coordinate data is changed. Counter display 0: Display the command value that does not expanded consider the tool length offset amount or function workpiece coordinate offset amount. selection 1: The counter display expanded function is validated. (bit4 to bit7)

Setting range (unit) 0/1

0/1

0/1

0/1

0/1

0/1

(Version D, M65)

II - 78

5.

BASE SPECIFICATIONS PARAMETERS

# ext23 (bit4)

Items Relative coordinate display

Details (M system) 0: Display the actual position including tool length offset. 1: Display the machining position in terms of a program command excluding tool length offset. (L system) 0: Display the actual position including tool shape compensation. 1: Display the machining position in terms of a program command excluding tool shape compensation. (M system) 0: Display the actual position including tool radius compensation. 1: Display the machining position in terms of a program command excluding tool radius compensation. (L system) 0: Display the actual position including nose R compensation. 1: Display the machining position in terms of a program command excluding nose R compensation. (M system) 0: Display the actual position including tool length offset. 1: Display the machining position in terms of a program command excluding tool length offset. (L system) 0: Display the actual position including tool shape compensation. 1: Display the machining position in terms of a program command excluding tool shape compensation.

Setting range (unit) 0/1

(Version D, M65) 0/1

ext23 (bit5)

Relative coordinate display

ext23 (bit6)

Absolute coordinate display [Special display unit compatible]

(Version D, M65) 0/1

(Version D, M65)

II - 79

5.

BASE SPECIFICATIONS PARAMETERS

# ext23 (bit7)

Items Absolute coordinate display [Special display unit compatible]

Details

1288 ext24 (PR) (bit0)

MDI program clear

1289 (PR) 1290 (PR) 1291 (PR) 1292 (PR) 1293 (PR) 1294 (PR) 1295 (PR) 1296 (PR) 1297 (PR) 1298 (PR)

ext25 ext26 ext27 ext28 ext29 ext30 ext31 ext32 ext33 ext34

(M system) 0: Display the actual position including tool radius compensation. 1: Display the machining position in terms of a program command excluding tool radius compensation. (L system) 0: Display the actual position including nose R compensation. 1: Display the machining position in terms of a program command excluding nose R compensation. With the L system, the effect onto the nose R compensation's absolute coordinate counter is also affected by the L system coordinate changeover parameter (#1227 aux11/bit 3 absolute coordinate changeover (nose R)). In actual use, if this parameter is set to 1, or if #1227 aux 11/bit 3 is set to 1, the position in the program commands will be displayed with the absolute coordinate counter. (Version D, M65) Select whether to initialize the MDI buffer when MDI 0/1 operation ends, the power is turned ON again, reset is input, or emergency stop is canceled. 0: Do not clear programs registered with MDI. 1: Clear programs registered with MDI, and save only % programs. Not used. Not used. Not used. Not used. Not used. Not used. Not used. Not used. Not used. Not used.

Setting range (unit) 0/1

II - 80

5.

BASE SPECIFICATIONS PARAMETERS

# 1299 ext35 (PR) 1300 ext36 (PR) (bit0) ext36 (bit7)

Items Not used. Multiple spindle control II Spindle synchronization command method

Details

Setting range (unit)

Select multiple spindle control I or II. 0/1 0: Multiple spindle control I 1: Multiple spindle control II (select from ladder) Select the spindle synchronization command 0/1 method. 0: Spindle synchronization with PLC I/F 1: Spindle synchronization with G command

II - 81

5.

BASE SPECIFICATIONS PARAMETERS

(SETUP PARAM 1. 10/15) # 1301 nrfchk Items Origin neighboring check method Details Select the high-speed check method of the origin neighboring signal. 0: Do not check positions near the origin at high speeds. (Conventional specifications) 1: Check positions near the origin at high speeds using command machine positions. 2: Check positions near the origin at high speeds using detector feedback positions. Automatic 0: Return the system to the restart position return by manually and then restart the program. program restart 1: For program restarting, the first activation automatically moves the system to the restart position. No. of #100 Set the number of common variables common for address the system starting from address #100. system common variables No. of #500 Set the number of common variables common for address the system starting from address #500. system common variables Corner Select whether to judge corner deceleration with a deceleration polygon shape or tangent during helical interpolation tangent and spiral interpolation. judgment 0: Polygon judgment Helical interpolation is interpreted as polygonal, and the corner deceleration is judged with the approximate vector. 1: Tangent judgment The vector is calculated from the center of the helical interpolation, the start point and the end point, and corner deceleration is judged. Deceleration Select the parameter specification type for the G0 or check G1 deceleration check. specification 0: Deceleration check specification type 1 type G0 is specified with #1193 inpos, and G1+G9 with #1223 aux07/BIT1. 1: Deceleration check specification type 2 G0 or G1+G9 is specified with #1193 inpos. Minimum value Set the minimum value for the M code. When 0 is for set, the synchronization M code will be invalid. synchronization M code Setting range (unit) 0 to 2

1302 AutoRP

0/1

1303 V1comN (PR)

0 to 100

1304 V0comN (PR)

0 to 500

1305 corjug

0/1

1306 InpsTyp

0/1

1310 WtMmin

0, 100 to 99999999

II - 82

5.

BASE SPECIFICATIONS PARAMETERS

# Items 1311 WtMmax Maximum value for synchronization M code 1312 T_base Tool life management standard number

Details Setting range (unit) Set the maximum value for the M code. When 0 is 0, 100 to 99999999 set, the synchronization M code will be invalid.

1313 TapDw1

1314 TapInp

1324 Chop_R

When the T code command is issued while specifying a value that exceeds the value set in this parameter, the value obtained by subtracting the set value from the command value is used as the tool group number for tool life management. The value specified by the T code command is equal to or less than the value set in this parameter, the T code is handled as a normal T code and not subjected to tool life management. When 0 is set in this parameter, the T code command always specifies a group number. (This parameter is valid for M-system tool life management II.) Synchronous Specify the hole bottom wait time for synchronous tap hole tapping. bottom wait When the P address is specified, the greater value time is used as the hole bottom wait time. When an in-position check is performed at the hole bottom, dwelling for the specified time is completed after the in-position check is complete. (Applicable only to the M64 D version series) Note: This parameter is valid only when 1 is set in #1223 aux07 bit 3 (synchronous tap in-position check improvement). Synchronous Specify the hole bottom in-position check width for tap in-position synchronous tapping. (Applicable only to the M64 D check width version series) (tap axis) Note: This parameter is valid only when 1 is set in #1223 aux07 bit 3 (synchronous tap in-position check improvement). Chopping Head number of the R register used as the compensacompensation amount save area during fixed tion value compensation amount method. fixing method

0 to 9999

0 to 999 (ms)

1 to 32767 (1m steps)

1900 to 2782

II - 83

5.

BASE SPECIFICATIONS PARAMETERS

(SETUP PARAM 1. 11/15) # 1501 polyax (For L system only) Items Rotational tool axis number Details Setting range (unit) Specify the number of the rotational tool axis (servo 0 to controlled axis axis) used for polygon machining (G51.2). Set 0 when number not using polygon machining (spindle-servo axis), or when using spindle-spindle polygon machining. A value exceeding the base specification parameter #1002 axisno cannot be specified. This parameter is valid when the G code system is 6 or 7 (7 or 8 is set in base specification parameter #1037 cmdtyp). 0: Do not perform a deceleration check when the 0/1 move direction is changed from G1 to G0. 1: Perform a deceleration check when the move direction is changed from G1 to G0. (Applicable only to the M64 D version series) 0: Do not perform a deceleration check when the 0/1 move direction is changed from G1 to G1. 1: Perform a deceleration check when the move direction is changed from G1 to G1. (Applicable only to the M64 D version series) 0/1

1502 G0Ipfg

G1 G0 deceleration check

1503 G1Ipfg

G1 G1 deceleration check

1505 ckref2

1506

1507

1510

1511

Second origin Specify the trigger for a check at the specified position return check in manual second original return mode. 0: Completion of spindle orientation 1: Generation of second origin return interlock signal F1_FM Upper limit of Specify the maximum value up to which the F1 digit feedrate can be changed. F1 digit feedrate (Applicable only to M65 and M66) F1_K F1 digit Specify the constant that determines the speed feedrate change rate per manual handle graduation in F1 digit change feedrate change mode. constant (Applicable only to M65 and M66) DOOR_H Shorten door Specify whether to shorten the time during which the axis is stopped when the door is opened. interlock II axis stop time 0: Use the conventional axis stop time. 1: Shorten the axis stop time. Note: When the door interlock II signal is input via a ladder, the conventional axis stop time is used. DOORPm Signal input Specify the fixed device number (X??) for door device 1 for interlock II signal input for each system. door interlock A device number from X01 to XFF can be specified. II: for each Device number 000 is invalid. system Specify device number 100 when using no fixed device number for door interlock II signal input. Related parameter: #1154 pdoor (Door interlock II for each system)

0 to 60000 (mm/min)

0 to 32767

0/1

000 to 100 (hexadecimal)

II - 84

5.

BASE SPECIFICATIONS PARAMETERS

# Items 1512 DOORPs Signal input device 2 for door interlock II: for each system 1513 stapM M code for synchronous tap selection

1514 expLinax

1515 expRotax

1516 mill_ax

Exponential function interpolation linear axis Exponential function interpolation rotary axis Milling axis name

Details Specify the fixed device number (X??) for door interlock II signal input for each system. (Specify the same value as that of #1155.) Related parameter: #1154 pdoor (Door interlock II for each system) Select the synchronous tap mode using the miscellaneous function code of the value set in this parameter. The M function command can be issued immediately before the tap command or in the same block. This function is valid only when 1 is set in #1272 ext08/bit 1 (Enable/disable M-function synchronous tap cycle). Note: Do not use M00, 01 02, 30, 98, and 99. Set the axis address name for the linear axis used in exponential function interpolation.

Setting range (unit) 000 to 100 (hexadecimal)

0 to 99999999

A to Z

Set the axis address name for the rotary axis used in exponential function interpolation.

A to Z

1517 mill_C

Milling interpolation hypothetical axis name

1518 polm

1519 pols

1520 Tchg34 (PR)

1521 C_min

Spindlespindle polygon Workpiece spindle No. Spindlespindle polygon Tool spindle No. Additional axis tool compensation operation Minimum turning angle

Set the name of the rotary axis used in milling interpolation. Only one rotary axis can be set. When there is no E command in issuing the G12.1 command, this parameter will be followed. Select the hypothetical axis command name for milling interpolation. When there is no D command in issuing the G12.1 command, this parameter will be followed. 0: Y axis command 1: Command rotary axis name. Set the number of the workpiece spindle used in spindle-spindle polygon machining. Note: The 1st spindle will be selected when 0 is set.

A to Z

0/1

0 to number of spindles

Set the number of the tool spindle used in spindlespindle polygon machining. Note: The 2nd spindle will be selected when 0 is set. Select whether to carry out the additional axis' tool compensation function with the 3rd axis or 4th axis. 0: Select 3rd axis. 1: Select 4th axis. Set the minimum turning angle of the normal line control axis at the block joint during normal line control.

0 to number of spindles

0/1

0.000 to 360.000 ()

II - 85

5.

BASE SPECIFICATIONS PARAMETERS

# 1522 C_axis (PR)

Items Normal line control axis

Details Set the number of the axis for normal line control. Designate a rotary axis.

1523 C_feed

1524 C_type

Normal line This is valid with normal line control type I. control axis Designate the turning speed of the normal line turning speed control axis at the block joint during normal line control. Set a value that does not exceed the normal line control axis' clamp speed (#2002 clamp). Normal line Set the normal line control type. control type

Setting range (unit) 0: Normal line control disabled 1 to 6: Axis No. (number of control axes) 0 to 1000000 (/min)

0: Normal line control type I 1: Normal line control type II

1525 laxlen 1526 raxlen 1527 flclen

1528 rflch

1529 laxcmp

1530 raxcmp

1531 flccmp

1532 G01rsm

1533 millPax

L axis length R axis length Distance between support points R point support point height L axis compensation amount R axis compensation amount Distance between support point compensation amount G00 L/R interpolation simultaneous reach Pole coordinate linear axis name

Special function Special function Special function

Special function

Special function

Special function

Special function

Special function

Set the linear axis used for pole coordinate interpolation.

Control axis address such as X, Y or Z

II - 86

5.

BASE SPECIFICATIONS PARAMETERS

# Items 1534 SnG44.1 Spindle No. for G44.1 command

Details Set the selected spindle No. for the G44.1 command. #1199 0:G43.1 1:G44.1 #1534 Not used. 0 1 2 3 4 Not used. Selected spindle 1st spindle 2nd spindle 1st spindle 2nd spindle 3rd spindle 4th spindle All spindles

2:G47.1 1535 C_leng Minimum turning movement amount Cross machining control axis

Set the minimum turning movement amount of the normal line control axis at the block joint during normal line control. Set the axis to be interchanged during cross machining control. Using two digits, set the name of the axis interchanged with that where the cross machining control request signal is input, or that moves to the position where the signal is input.

Setting range (unit) 0: 2nd spindle 1: 1st spindle 2: 2nd spindle 3: 3rd spindle 4: 4th spindle If a spindle that does not exist is set, the 2nd spindle will be used. Note that if there is only one spindle, the 1st spindle will be used. 0.000 to 99999.999 (mm)

1537 crsax[1] to to 1544 crsax[8]

Two digits between A to Z and 1 to 9 (Setting is cleared when 0 is set)

(SETUP PARAM 1. 12/15) # 1549 Iv0vr1 Items Details Override 1 start Set the override 1 start curvature radius for curvature radius executing involute interpolation with the high-speed high-accuracy II mode. Override 2 start Set the override 2 start curvature radius for curvature radius executing involute interpolation with the high-speed high-accuracy II mode. Override 3 start Set the override 3 start curvature radius for curvature radius executing involute interpolation with the high-speed high-accuracy II mode. Override 4 start Set the override 4 start curvature radius for curvature radius executing involute interpolation with the high-speed high-accuracy II mode. Override 5 start Set the override 5 start curvature radius for curvature radius executing involute interpolation with the high-speed high-accuracy II mode. Setting range (unit) 0.001 to 99999.999 (mm) 0.001 to 99999.999 (mm) 0.001 to 99999.999 (mm) 0.001 to 99999.999 (mm) 0.001 to 99999.999 (mm)

1550 Iv0vr2

1551 Iv0vr3

1552 Iv0vr4

1553 Iv0vr5

II - 87

5.

BASE SPECIFICATIONS PARAMETERS

# 1554 Iv0rd2

Items Involute interpolation override 2

1555 Iv0rd3

Involute interpolation override 3

1556 Iv0rd4

Involute interpolation override 4

1557 Iv0rd5

Involute interpolation override 5

1558 Iv0Min

Involute interpolation override lower limit value Involute interpolation maximum acceleration rate

1559 IvAMax

1560 IvFMin

Involute interpolation minimum feedrate

1572 Cirorp

Arc command overlap

Details Set the override value at the curvature radius Iv0vR2 for executing involute interpolation with the high-speed high-accuracy II mode. Note: If the override value is not set (setting value: 0), the setting will be invalid, and the override will be 100%. Set the override value at the curvature radius Iv0vR3 for executing involute interpolation with the high-speed high-accuracy II mode. Note: If the override value is not set (setting value: 0), the setting will be invalid, and the override will be 100%. Set the override value at the curvature radius Iv0vR4 for executing involute interpolation with the high-speed high-accuracy II mode. Note: If the override value is not set (setting value: 0), the setting will be invalid, and the override will be 100%. Set the override value at the curvature radius Iv0vR5 for executing involute interpolation with the high-speed high-accuracy II mode. Note: If the override value is not set (setting value: 0), the setting will be invalid, and the override will be 100%. Set the lower limit value of the involute interpolation override. Note: If the override value is not set (setting value: 0), the setting will be invalid, and the override will be 100%. Set the maximum acceleration rate of the constant acceleration control for executing involute interpolation with the high-speed high-accuracy II mode. Note: If this parameter is not set (setting value: 0), the setting will be invalid, and the normal acceleration rate (#1207 G1btL) will be applied. Set the minimum feedrate of the constant acceleration control for executing involute interpolation with the high-speed high-accuracy II mode. (Valid when executing compensation with the accuracy coefficient.) Note: If this parameter is not set (setting value: 0), the feedrate will not be clamped. Fluctuation of the speed at the arc and linear or arc and arc joints will be eliminated during the high-speed high-accuracy II mode. 0: Do not overlap arc command blocks. 1: Overlap arc command blocks. (Eliminate the speed fluctuation)

Setting range (unit) 1 to 100 (%)

1 to 100 (%)

1 to 100 (%)

1 to 100 (%)

1 to 100 (%)

1 to 32767 (ms)

1 to 32767 (ms)

0/1

II - 88

5.

BASE SPECIFICATIONS PARAMETERS

(SETUP PARAM 1. 13/15) # 1801 Hacc_c 1802 Macc_c 1803 Lacc_c 1811 Hcof_A 1812 Hcof_B 1813 Mcof_A 1814 Mcof_B 1815 Lcof_A 1816 Lcof_B 1817 mag_C 1821 Hcof_A 1822 Hcof_B 1823 Mcof_A 1824 Mcof_B 1825 Lcof_A 1826 Lcof_B 1827 mag_C Items Details Arc radius clam acceleration Setting range (unit) -99999999 to +99999999 Acceleration check at middle speed -99999999 to +99999999 Acceleration check at low speed -99999999 to +99999999 -99999999 to X-axis high acceleration coefficient +99999999 -99999999 to X-axis high acceleration coefficient +99999999 -99999999 to X-axis middle acceleration coefficient +99999999 -99999999 to X-axis middle acceleration coefficient +99999999 -99999999 to X-axis low acceleration coefficient +99999999 -99999999 to X-axis low acceleration coefficient +99999999 -99999999 to X-axis change magnification [%] +99999999 Set 0 when no compensation or change is executed. -99999999 to Y-axis high acceleration coefficient +99999999 -99999999 to Y-axis high acceleration coefficient +99999999 -99999999 to Y-axis middle acceleration coefficient +99999999 -99999999 to Y-axis middle acceleration coefficient +99999999 -99999999 to Y-axis low acceleration coefficient +99999999 -99999999 to Y-axis low acceleration coefficient +99999999 -99999999 to Y-axis change magnification [%] +99999999 Set 0 when no compensation or change is executed.

II - 89

5.

BASE SPECIFICATIONS PARAMETERS

(SETUP PARAM 1. 14/15) # Items 1901 station addr (PR) 1902 Din size (PR) 1903 Dout size (PR) 1904 data length (PR) 1905 baud rate (PR) Details Set up a station address number (the NC is the n-th slave station). Set up the size of the data to be transferred from the PC to the NC (from the master station to the slave station) in bytes (8 points). Set up the size of the data to be transferred from the NC to the PC (from the slave station to the master station) in bytes (8 points). Set up the data length of a character. Setting range (unit) 1 to 7 0 to 32 (bytes (8 bits)) 0 to 32 (bytes (8 bits))

1906 (PR) 1907 (PR) 1908 (PR) 1909 (PR) 1910 (PR)

stop bit parity check even parity Tout (ini)

(run)

0 to 2 : 7 bits 3 : 8 bits Set up a data transfer rate. The transfer rate differs Clock: 6 MHz/ according to operation clock rates 10 MHz 0: 38400 / 57600 1: 19200 / 28800 2: 9600 / 14400 3: 4800 / 7200 4: 2400 / 3600 5: 1200 / 1800 6: 600 / 900 (bps) Set up the stop bit length. 0 and 1: 1 bit 2 and 3: 2 bits Select whether to make a parity check. 0: Invalid 1: Valid Select the odd or even parity bit. If no parity check is 0: Odd parity specified, this parameter is ignored. 1: Even parity (ini) specifies a time-out from when the connection 0 to 999 (0.1 s) check sequence finishes to when the first usual sequence (input) finishes. (run) specifies a time-out from when the NC (slave station) outputs usual sequence data to when the next usual sequence data is input. If the time-out is exceeded, an emergency stop occurs and the system waits for the preparation sequence to start. If the set value is 0, no time-out occurs or no communication stop can be detected. Select an operation cycle.

1911 clock select (PR)

0: 6 MHz 1: 10 MHz

II - 90

5.

BASE SPECIFICATIONS PARAMETERS

(SETUP PARAM 1. 15/15) # Items Details 1925 EtherNet Start of service Start or stop the Ethernet communication function. 0: Stop 1: Start 1926 IP IP address Specify the NC IP address address 1927 Subnet mask 1928 Gateway address 1929 Port number 1930 Host address 1931 Host number Subnet mask Gateway Port No. Host address Host No. Specify the subnet mask. Specify the gateway IP address. Set the port No. for the service function. Set the host's IP address. Set the host's port No. Setting range (unit) 0/1

Set these parameters in accordance with the network rules in the connection environment. 1 to 9999 1 to 255 1 to 9999

II - 91

6. 6.1

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS

6.

AXIS SPECIFICATIONS PARAMETERS

6.1 AXIS SPECIFICATIONS PARAMETERS

After setting up the parameter (PR) listed in the table, turn OFF the NC power. To validate the parameter, turn ON the power again. (SETUP PARAM 2. 1/8) # 2001 rapid Details Setting range (unit) Set up the rapid traverse feedrate for each axis. 1 to 999999 (mm/min) The maximum value to be set differs with mechanical systems. Cutting feedrate Define the maximum cutting feedrate for each axis. 1 to 999999 (mm/min) for clamp Even if the feedrate in G01 exceeds this value the function clamp will be applied at this feedrate. Acceleration and Specify acceleration and deceleration control modes. deceleration F E D C B A 9 8 7 6 5 4 3 2 1 modes
O T3 O T2 O T1 C 3 C1 LC R3 R1

Items Rapid traverse rate

2002 clamp

2003 smgst (PR)

Specify the modes in hexadecimal notation.

0
LR

Note: Set 0 in null bits. Rapid traverse feed acceleration and deceleration types LR: Linear acceleration/deceleration R1: Primary delay R3: Exponential acceleration and linear deceleration Note: Designate F with bits 0 to 3 for rapid traverse with acceleration/deceleration by software. Cutting feed acceleration and deceleration types LC: Linear acceleration/deceleration C1: Primary delay C3: Exponential acceleration and linear deceleration Note: Designate F with bits 4 to 7 for cutting feed with acceleration/deceleration by software. (To be continued to the next page)

II - 92

6. 6.1

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS

Items

Details (Continued from the previous page) <Combination of acceleration and deceleration patterns>
Primary delay

Setting range (unit)

R1=1 (C1=1)
Command speed Linear to linear

LR=1 (LC=1)
Step

LR=0 (LC=0)
Parameters in parentheses are for cutting feed.

Exponential to linear

R3=1 (C3=1)
Step

R1-R3=0 (C1-C3=0)

R1 > R3 when both R1 and R3 contain 1. <Stroke end stop types> Type Linear deceleration Position loop step stop Speed loop step stop Position loop step stop OT1 0 1 OT2 0 1 0 1 OT3 0 0 1 1

Deceleration by G0t1 Deceleration by 2 G0t1

Stroke end signal

Speed

Time G0t1 G0t1 2 G0t1(OT1=1) (OT1=0)

OT1 is valid under the following conditions (valid for dog type zero point return): Stop type: Linear deceleration Acceleration mode: Exponential Deceleration mode: Linear

II - 93

6. 6.1

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS

# 2004 G0tL

Items Details Setting range (unit) G0 time constant Set up a linear control time constant for rapid traverse 1 to 4000 (ms) (linear) acceleration and deceleration. The time constant is validated when LR (rapid traverse feed with linear acceleration or deceleration) or F (acceleration or deceleration by software) is selected in acceleration or deceleration mode #2003 smgst.
Speed Time G0tL G0tL

2005 G0t1

G0 time constant Set up a primary-delay time constant for rapid 1 to 5000 (ms) traverse acceleration and deceleration. (primary delay) The time constant is validated when R1 (rapid traverse feed with primary delay) or R3 (exponential acceleration and linear deceleration) is selected in acceleration or deceleration mode #2003 smgst. Second-step time constant for acceleration and When acceleration or deceleration by software is deceleration by selected, the second-step time constant is used. software
<Rapid traverse feed with primary delay>
Speed Time G0t1 G0t1

<Rapid traverse feed with exponential acceleration and linear deceleration>

Speed Time G0t1 2 G0t1

2006 G0t2

Not used.

II - 94

6. 6.1

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS

# 2007 G1tL

Items G1 time constant (linear)

Details Setting range (unit) Set up a linear control time constant for cutting 1 to 4000 (ms) acceleration and deceleration. The time constant is validated when LC (cutting feed with linear acceleration and deceleration) or F (acceleration and deceleration by software) is selected in acceleration or deceleration mode #2003 smgst.
Speed Time G1tL G1tL

2008 G1t1

Set up the primary delay time constant for cutting G1 time 1 to 5000 (ms) acceleration and deceleration. constant (primary delay) The time constant is validated when C1 (cutting feed with the primary delay) or C3 (cutting feed with exponential acceleration and linear deceleration) is selected in acceleration or deceleration mode #2003 smgst. Second stage When acceleration or deceleration by software is time constant for acceleration selected, the second stage time constant is used. and deceleration by <Cutting feed with primary time constant> software
Speed Time G1t1 G1t1

<Cutting feed with exponential acceleration and linear deceleration>

Speed Time G1t1 2 G1t1

2009 G1t2

Not used.

II - 95

6. 6.1

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS

# 2010 fwd_g

Items Feed forward gain

2011 G0back

G0 backlash G1 backlash

2012 G1back

Details Set up a feed forward gain for pre-interpolation acceleration and deceleration. The larger the set value, the smaller the theoretical control error will be. However, if a mechanical vibration occurs, the set value must be reduced. Set up the backlash compensation amount when the direction is reversed with the movement command in rapid traverse feed mode or in manual mode. Set up the backlash compensation amount when the direction is reversed with the movement command in cutting mode.

Setting range (unit) 0 to 100 (%)

9999 to 9999 (command unit / 2) 9999 to 9999 (command unit / 2)

II - 96

6. 6.1

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS

(SETUP PARAM 2. 2/8) # 2013 0T 2014 0T + Items Soft limit I soft limit I + Details Setting range (unit) Set up a soft limit area with reference to the zero point 99999.999 (mm) of the basic mechanical coordinates. For the movable area of stored stroke limit 1, set the coordinate in the negative direction in #2013 and the coordinate in the positive direction in #2014. To narrow the available range in actual use, use the parameters #8204 OT- and #8205 OT+. When the same value (other than 0) is set in #2013 and #2014, this function is disabled.

Basic mechanical coordinates OT- (X) Movable area M OT+ (X)

OT+ (Z)

OT- (Z)

2015 t1m1

Negative direction sensor of tool setter or TLM standard length

Set up a sensor position in the negative direction 99999.999 (mm) when using the tool setter. When the TLM is used, set up the distance of a tool replacement point (reference point) for measuring the tool length from the zero point to the measurement reference point (surface). 99999.999 (mm)

2016 t1m1+

2017 tap_g

2018 no_srv

Set up the sensor position in the positive direction Positive when using the tool setter. direction sensor of tool setter Axis servo gain Set the position loop gain for special operations (synchronized tapping, interpolation with spindle C axis, etc.) The setting range is 1.00 to 200.00rad/s. in 0.25 increment units. The standard setting is 10. Operation with Set when performing test operation without connecting the drive amplifier and motor. no servo 0: Specify normal operation. control 1: Operation is possible even if units are not connected as the drive system alarm will be ignored. This is for test operation during start up and is not used normally. If 1 is set during normal operation errors will not be detected even if they occur.

1.00 to 200.00 (rad/s)

0/1

II - 97

6. 6.1

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS

# 2019 revnum

Items Return steps

2020 o_chkp

Spindle orientation completion check during second zero point return 2021 out_f Maximum speed outside soft limit range 2022 G30SLX Validate soft limit (automatic and manual)

Details Set up the steps required for reference point return for each axis. 0: Does not execute reference point return. 1 to max. number of NC axes: Sets up the steps required for reference point return. Set up the distance from the second zero point to the position for checking that the spindle orientation has completed during second zero point return. If the set value is 0, the above check is omitted.

Setting range (unit) 0 to max. number of NC axes

0 to 99999.999 (mm)

Set up the maximum speed outside the soft limit range.

0 to 999999

2023 ozfmin

2024 synerr

Set up this function to disable a soft limit check during the second to the fourth zero point return in both automatic and manual operation modes. 0: Enables soft limit check. 1: Disables soft limit check. Set up the minimum speed outside the soft limit Set up ATC range during the second to the fourth zero point speed lower return in both automatic and manual operation limit modes. Allowable error Set up the following for the master axis: the maximum synchronization error that is allowed to check for synchronization errors When 0 is set up, the error check is not carried out.

0/1

0 to 999999

0 to 99999.999 (mm) During spindle C axis synchroniza tion control: 0 to 99999.999 ()

II - 98

6. 6.2

AXIS SPECIFICATIONS PARAMETERS ZERO POINT RETURN PARAMETERS

6.2 ZERO POINT RETURN PARAMETERS

After setting up the parameter (PR) listed in the table, turn OFF the NC power. To validate the parameter, turn ON the power again. (SETUP PARAM 2. 3/8) # Items 2025 G28rap G28 rapid traverse rate 2026 G28crp G28 approach speed Details Set up a rapid traverse rate for dog type reference point return command. Set up the speed of approach to the reference point in the reference point return command. This speed is attained after the system stops with deceleration by dog detection. Note) The G28 approach speed unit is (10/min) only when using the Z-phase type encoder (#1226 aux10 bit3=1) for the spindle/C-axis reference point return type. The same unit is used for both the micron and sub-micron specifications. Set up the distance from the electrical zero-point detection position to the actual machine reference point during reference point return. Set up a distance where the grid point is ignored when near-point dog OFF signals are close to that grid point during reference point return. Setting range (unit) 1 to 999999 (mm/min) 1 to 60000 (mm/min)

2027 G28sft

2028 grmask

Reference point shift distance Grip mask amount

0 to 65535 (m)

0 to 65535 (m) Even for the specifications in sub-microns, set up the value in units of m.

2029 grspc

Grid interval

The grid mask is valid by one grid. Set up a detector grid interval. 32767 to 999 (mm) Generally, set up the value equal to the ball screw pitch. However, if the detector grid interval is not equal to the screw pitch when measured with a linear scale, set up the detector grid interval. To reduce the grid interval, use its divisors. To use 0.001 mm as minimum setup units, set up the negative value. Example) Setup value 1 1.000 mm () 1 0.001 mm () Even when the specifications in sub-microns are used, 0.001 mm is specified for the minimum setup units.

II - 99

6. 6.2

AXIS SPECIFICATIONS PARAMETERS ZERO POINT RETURN PARAMETERS

# 2030 dir () (PR)

Items Reference point direction ()

Details Set which side of the near-point dog the reference point is at during reference point return. <For dog type reference point return>

Setting range (unit) 0: Positive direction 1: Negative direction

Direction in which zero point is established as viewed from the near-point dog Negative direction Near-point dog dir(-)=0 Positive direction

dir(-)=1

2031 noref

2032 nochk

2033 zp_no

Axis without Specify the axis that does not have a reference point. 0: Normal controlled axis reference point Before automatic operation starts, reference point 1: Axis without return is not required. reference point 0: Reference point The absolute and incremental commands can be Whether return completion reference point executed even if dog type (or Z phase pulse system) is checked. reference point return is not completed. return is 1: Reference point completed not Specify whether to check that the reference point return completion return is completed. checked is not checked. 0: Dog type Z phase pulse The reference point return is performed with the Z phase pulse of the spindle encoder. Set the spindle 1 to 4: Spindle No. system reference point encoder No. to be used. return spindle encoder No.

II - 100

6. 6.2

AXIS SPECIFICATIONS PARAMETERS ZERO POINT RETURN PARAMETERS

(SETUP PARAM 2. 4/8) # 2037 2038 2039 2040 G53ofs #2_rfp #3_rfp #4_rfp Items Reference point #1 to #4 Details Setting range (unit) Set up the position of the first, second, third, and fourth 999999.999 (mm) reference points from the zero point of the basic mechanical coordinates.

Basic mechanical coordinates Reference point #1 M

Reference point #2

Reference point #3

Reference point #4

II - 101

6. 6.3

AXIS SPECIFICATIONS PARAMETERS ABSOLUTE POSITION PARAMETERS

6.3 ABSOLUTE POSITION PARAMETERS

(SETUP PARAM 2. 5/8) # 2049 type (PR) Items Absolute position detection method Details Specify the absolute position zero point alignment method. 0: Not absolute position detection 1: Stopper method (push with mechanical stopper) 2: Origin point alignment method (align with marked point) 3: Dog-type (align with dog and proximity switch) 4: Reference point alignment method II (align to alignment mark) (Type that does not return grid after reference alignment) 9: Simple absolute position (Not absolute position detection but the position when the power is turned off is registered.) Automatic initial setting is valid only when the stopper method is selected. Base point Set the direction of the absolute position reference point (grid point immediately before) seen from the machine of Z reference point for when using reference point direction alignment. Check Set the tolerable range for the movement amount (deviation amount) when the power is turned OFF. 0: Not checked 1 to 99999.999mm: If the difference of the position when the power is turned OFF and turned ON again is larger than this value an alarm will be output. Not used. Not used. Current limit Set up the current limit value for the initial setting when (%) detecting an absolute position with a dog-less system. The setup value is the ratio of the current limit value to the rated value. Push speed Set the feedrate for the automatic initial setting during stopper method. Approach Set the approach distance for the automatic initial setting in the push method. Approach distance: After using stopper once the tool returns this distance and then use stopper again. When set to 0 the reference point coordinates set in #2037 G53ofs will be used as the approach start position. Setting range (unit) 0 to 9

2050 absdir

0: Positive direction 1: Negative direction 0 to 99999.999 (mm)

2051 check

2052 absg28 2053 absm02 2054 clpush

0 to 100 (%)

2055 pushf 2056 aproch

1 to 999 (mm/min) 0 to 999.999 (mm)

II - 102

6. 6.3

AXIS SPECIFICATIONS PARAMETERS ABSOLUTE POSITION PARAMETERS

# 2057 nrefp

Items Near zero point +

2058 nrefn

2059 zerbas

Details Set the width where the near-reference-point signal is output. (Positive direction width) When set to 0 the width is equivalent to the grid width setting. Near zero Set the width where the near-reference-point signal is output. (Negative direction width) point When set to 0 the width is equivalent to the grid width setting. Specify the position to be the zero point coordinate Select zero during absolute position initial setting. point 0: Position that was stopped during stopper parameter method and reference Specify the coordinates of the alignment mark point position when using the reference point method. 1: Grid point just before stopper Specify the coordinates of the grid point just before the alignment mark.

Setting range (unit) 0 to 32.767 (mm)

0 to 32.767 (mm)

0/1

II - 103

6. 6.4

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS 2

6.4 AXIS SPECIFICATIONS PARAMETERS 2

(SETUP PARAM 2. 6/8) # Items Details 2061 0T_1B Soft limit IB Set up the coordinates of the lower limit of the inhibited area of stored stroke limit IB. Specify a value in the basic mechanical coordinates system. If the same value (non-zero) with the same sign as that of #2062 0T_IB+ is specified, the stored stroke limit IB function is disabled. 2062 0T_1B+ Soft limit IB+ Set up the coordinates of the upper limit of the inhibited area of stored stroke limit IB. Specify a value in the basic mechanical coordinates system. 2063 0T_1B Soft limit IB Select 0T_IB or 0T_IC in which 0T_IB+/ is used in type type stored stroke limit I. 0: Soft limit IB valid 1: Soft limit IB invalid 2: Soft limit IC valid 3: When using the inclined axis specifications, the soft limit is checked with the program coordinate system. Note: This is invalid for axes other than the inclined axis' base axis and inclined axis. 2064 rapid2 Speed 2 Specify the speed applicable to the speed area for 2-stage acceleration/deceleration. If the following conditions are not satisfied, inclination constant acceleration/deceleration is used for operation. (0 < rapid2 < rapid and rapid3 = 0 and 0 < G0tL2 <G0tL and G0tL3 = 0) (Applicable only to M64 D version series) Related parameters: #1223 aux07 bit 0 (Rapid traverse content multistage acceleration/deceleration) #2065 G0tL2 (Time constant 2) 2065 G0tL2 Time Specify the time constant applicable to the speed area constant 2 for 2-stage acceleration/deceleration. If the following conditions are not satisfied, inclination constant acceleration/deceleration is used for operation. (0 < rapid2 < rapid and rapid3 = 0 and 0 < G0tL2 <G0tL and G0tL3 = 0) (Applicable only to M64 D version series) Related parameters: #1223 aux07 bit 0 (Rapid traverse content multistage acceleration/deceleration) #2064 rapid2 (Speed 2) Setting range (unit) 99999.999 (mm)

99999.999 (mm)

0/1/2/3

0 to 999999 (mm/min) 0: No setting

1 to 4000 (ms) 0: No setting

II - 104

6. 6.4

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS 2

# 2066 rapid3

Items Speed 3

2067 G0tL3

2068 G0fwdg

2069 Rcoeff

2070 div_RT (PR)

Details Specify the speed applicable to the speed area for 2-stage or 3-stage acceleration/deceleration. If the following conditions are not satisfied, inclination constant acceleration/deceleration is used for operation. (0 < rapid3 < rapid2 < rapid and 0 < G0tL3 <G0tL2 < G0tL) (Applicable only to M64 D version series) Related parameters: #1223 aux07 bit 0 (Rapid traverse content multistage acceleration/deceleration) #2067 G0tL3 (Time constant 3) Time Specify the time constant applicable to the speed area constant 3 for 2-stage or 3-stage acceleration/deceleration. If the following conditions are not satisfied, inclination constant acceleration/deceleration is used for operation. (0 < rapid3 < rapid2 < rapid and 0 < G0tL3 <G0tL2 < G0tL) (Applicable only to M64 D version series) Related parameters: #1223 aux07 bit 0 (Rapid traverse content multistage acceleration/deceleration) #2066 rapid3 (Speed 3) Specify the feed forward gain applicable to G00 feed acceleration/deceleration before G00 interpolation. forward The greater the set value, the shorter the positioning gain time during in-position checking. If machine vibration occurs, decrease the set value. The amount of arc radius error correction can be Axis arc radius error increased or decreased between -100% to +100% for correction each axis. efficient Rotational Specify the number of divisions of one turn of the rotational axis for purpose of control. axis Example: When 36 is set, one turn is supposed to be division 36.000. count Note 1: When 0 is set, the normal rotational axis (360.000 degrees for one turn) is assumed. Note 2: If this parameter is changed when the absolute position detection specification is used, absolute position data is lost. Initialization must be performed again.

Setting range (unit) 0 to 999999 (mm/min) 0: No setting

1 to 4000 (ms) 0: No setting

0 to 200 (%)

-100.0 to +100.0 (%)

0 to 999

II - 105

6. 6.4

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS 2

# Items 2071 s_axis Inclined axis selection (For L system only)

2072 rslimt

Restart limit

Details Setting range (unit) Select the axis subjected to inclined-axis control or the 0 to 2 base axis corresponding to the inclined axis. 0: Axis not subjected to inclined-axis control 1: Inclined axis 2: Base axis corresponding to inclined axis Note: Set 1 or 2 for only one axis. If it is set for two or more axes, inclined-axis control does not work. If the machine is positioned on the minus (-) side of the 9999.999 (mm) set value in T-command restart mode, restart search in type 3 is disabled.

II - 106

6. 6.4

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS 2

(SETUP PARAM 2. 7/8) # Items Details 2073 zrn_dog Origin dog Under the standard specifications, the origin dog signal is assigned to a fixed device. When it is desired to assign the origin dog signal to a position other than the fixed device, specify the input device in this parameter. Note 1: This parameter is valid when 1 is set in #1226 aux10 bit 5. Note 2: When this parameter is valid, do not set the same device number. If the same device number exists, an emergency stop occurs. However, no device number check is performed for an axis to which a signal that ignores the near-point dog signal (R157) is input. 2074 H/W_OT+ H/W OT+ Under the standard specifications, the OT (+) signal is assigned to a fixed device. When it is desired to assign the OT (+) g signal to a position other than the fixed device, specify the input device in this parameter. Note 1: This parameter is valid when 1 is set in #1226 aux10 bit 5. Note 2: When this parameter is valid, do not set the same device number. If the same device number exists, an emergency stop occurs. However, no device number check is performed for an axis to which a signal that ignores the OT signal (R156) is input. 2075 H/W_OT- H/W OT- Under the standard specifications, the OT (-) signal is assigned to a fixed device. When it is desired to assign the OT (-) g signal to a position other than the fixed device, specify the input device in this parameter. Note 1: This parameter is valid when 1 is set in #1226 aux10 bit 5. Note 2: When this parameter is valid, do not set the same device number. If the same device number exists, an emergency stop occurs. However, no device number check is performed for an axis to which a signal that ignores the OT signal (R156) is input. Setting range (unit) 00 to FF (HEX)

00 to FF (HEX)

00 to FF (HEX)

II - 107

6. 6.4

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS 2

# Items 2076 index_x Index table indexing axis

2077 G0inps

G0 in-position width

2078 G1inps

G1 in-position width

2079 chcomp

2080 chwid

Chopping compensation coefficient Bottom dead center position width Maximum chopping speed

Details Specify the index table indexing axis. 0: Normal axis 1: Index table indexing axis Note: This parameter is valid only for the NC axis. The parameter is invalid if specified for the PLC axis. When an in-position check is performed for G0, this parameter is valid. (Comparison of SV024 and this parameter, the parameter that the in-position width is wider is applied.) When 0 is set, this parameter is invalid. (Applicable only to SV024) When an in-position check is performed for G1, this parameter is valid. (Comparison of SV024 and this parameter, the parameter that the in-position width is wider is applied.) When 0 is set, this parameter is invalid. (Applicable only to SV024) Set the coefficient applied on the compensation amount for the insufficient amount caused by servo delay during chopping. Set the tolerance between the commanded stroke and actual stroke. During chopping, if the (command width - maximum stroke of top/bottom dead center position /2) is within this tolerance, compensation will be applied. Set the chopping axis clamp speed applied during chopping.

Setting range (unit) 0/1

0 to 32767 (m) M64 specifies a 0.5 m unit.

0 to 32767 (m) M64 specifies a 0.5 m unit.

0 to 10 (standard value: 8)

2081 chclsp

2082 a_rstax

Designate the order for automatically returning to the Restart restart position. position 0: Do not return. return order When 0 is designated for all axes, all of the axes will return simultaneously.

Micron: 0 to 10000 (m) Sub-micron: 0 to 10000 (0.1 m) Micron: 0 to 60000 (mm/min) Sub-micron: 0 to 60000 (0.1 mm)/min 0 to 6

II - 108

6. 6.4

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS 2

# 2083 rot_2

Items Linear type rotary axis II

Details Setting range (unit) 0/1 The linear type rotary axis II is validated. 0: Invalidate linear type rotary axis II. 1: Validate linear type rotary axis II. Note that this is valid only when the power is turned ON, and the rotary axis parameters must be validated. The axis type is determined by the combination with the existing rotary axis parameters (#1017 rot rotary axis). If #1017 is set to 0, the linear axis will be applied. When #1017 is set to 1 and this parameter is set to 0, the rotary axis will be applied, and when set to 1, the linear type rotary axis II will be applied. <Related parameters> #1089: Cut_RT Short cut for rotary axis #1090: Lin_RT Linear type rotary axis #2070: div_RT Rotary axis division count #2076: index_x Index table indexing axis Note: These parameters are invalid when the linear type rotary axis II is set. 0/1 Select the unidirectional positioning with G00. Select the axis for carrying out the positioning per time operation when the positioning command is issued regardless of the unidirectional positioning command and modal. 0: Carry out unidirectional positioning according to the command and modal. 1: When the positioning command (G00) is issued, carry out unidirectional positioning regardless of the command and modal. <Related parameters> #8209 G60 SHIFT: The final positioning direction and distance for the unidirectional positioning command is set for each axis. #2076 Index table indexing axis: Set the indexing axis for each axis.

2084 G60_ax

Unidirectional positioning operation selection

II - 109

6. 6.4

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS 2

(SETUP PARAM 2. 8/8) # 2086 exdcax Items External deceleration speed Details Setting range (unit) Set the upper limit of the feedrate for each axis when 1 to 999999 (mm/min) the external deceleration signal is valid. This parameter is valid when the #1239 set11/bit6 external deceleration axis compliance valid is set to 1. 0 to FF BIT0: Polarity of synchronous axis in respect to reference axis 0: Polarity with reference axis is positive 1: Polarity with reference axis is negative (hexadecimal) 1st character: A to Z 2nd character: A to Z, 1 to 9 1st character: A to Z 2nd character: A to Z, 1 to 9 1 to 999999 (mm/min)

2087 syncnt

Synchronization/superimposition control setting for each axis Reference axis for synchronous control Reference axis for superimposition control Rapid traverse rate for superimposition control Cutting feed clamp speed for superimposition control G0 time constant for superimposition control (linear) G0 time constant for superimposition control (primary delay) G1 time constant for superimposition control (linear)

2088 bsax_sy

Set the reference axis for synchronous control with the 2nd axis name (axname2).

2089 bsax_pl

Set the reference axis for superimposition control with the 2nd axis name (axname2).

2090 plrapid

Set the rapid traverse rate for superimposition control. (Equivalent to #2001 rapid (rapid traverse rate).)

2091 plclamp

Set the cutting feed clamp speed for superimposition 1 to 999999 (mm/min) control. (Equivalent to #2002 clamp (cutting feed clamp speed).) Set the G0 time constant (linear) for superimposition 1 to 4000 (ms) control. (Equivalent to #2004 G0tL (G0 time constant (linear).) Set the G0 time constant (primary delay) for superimposition control. (Equivalent to #2005 G0t1 (G0 time constant (primary delay).) 1 to 5000 (ms)

2092 plG0tL

2093 plG0t1

2094 plG1tL

Set the G1 time constant (linear) for superimposition 1 to 4000 (ms) control. (Equivalent to #2007 G1tL (G1 time constant (linear).)

II - 110

6. 6.4

AXIS SPECIFICATIONS PARAMETERS AXIS SPECIFICATIONS PARAMETERS 2

# 2095 plG1t1

Items G1 time constant for superimposition control (primary delay) 2096 crncsp Minimum corner deceleration speed 2099 igConr Axis excluded from corner angle calculation 2102 skip_tL Skip time constant linear

Details Set the G1 time constant (primary delay) for superimposition control. (Equivalent to #2008 G1t1 (G1 time constant (primary delay).)

Setting range (unit) 1 to 5000 (ms)

Set the minimum clamp speed for corner deceleration during the high-accuracy control mode.

0 to 1000000 (mm/min)

Set the axis excluded from the corner angle calculation. 0/1 For example, set this for the Cs axis during spring machining.

Set up a linear control time constant for variable speed 1 to 4000 (ms) skip acceleration and deceleration. The time constant is validated when LC (cutting feed with linear acceleration and deceleration) or F (acceleration and deceleration by software) is selected in acceleration or deceleration mode #2003 smgst. Set up a primary-delay time constant for variable speed 1 to 5000 (ms) 2103 skip_t1 Skip time skip acceleration and deceleration. constant primary delay The time constant is validated when C1 (cutting feed with primary delay) or C3 (exponential acceleration and acceleration linear deceleration) is selected in acceleration or and deceleration deceleration mode #2003 smgst. When acceleration or deceleration by software is by software second stage selected, the second-step time constant is used.

II - 111

7.

SERVO PARAMETERS

7.

SERVO PARAMETERS
The parameters can be changed from any screen. The valid servo parameters will differ according to the motor type. The setting values and meanings may also differ. Follow the correspondence table given below, and set the correct parameters. Refer to each Instruction Manual or the following manuals for details on each motor. MELDAS AC Servo/ Spindle MDS-A Series MDS-B Series Specification Manual................ BNP-B3759 MELDAS AC Servo MDS-B-SVJ2 Series Specification and Instruction Manual...................... BNP-B3937 MELDAS AC Servo/ Spindle MDS-C1 Series Specification Manual...................................... BNP-C3000 Corresponding model MDS-C1-Vx MDS-C1-Vx MDS-B-SVJ2 (High-gain) (Standard) (MDS-B-Vx4) (MDS-B-Vx)

Parameter SV001 SV002 SV003 SV004 SV005 SV006 SV007 SV008 SV009 SV010 SV011 SV012 SV013 SV014 SV015 SV016 SV017 SV018 SV019 SV020 SV021 SV022 SV023 SV024 SV025 SV026 SV027 SV028 SV029 SV030 SV031 SV032 Motor side gear ratio Machine side gear ratio Position loop gain 1 Position loop gain 2 Speed loop gain 1 Speed loop gain 2 Speed loop delay compensation Speed loop lead compensation Current loop q axis lead compensation Current loop d axis lead compensation Current loop q axis gain Current loop d axis gain Current limit value Current limit value in special control Acceleration rate feed forward gain Lost motion compensation 1 Servo specification selection Ball screw pitch Position detector resolution Speed detector resolution Overload detection time constant Overload detection level Excessive error detection width during servo ON In-position detection width Motor/Detector type Excessive error detection width during servo OFF Servo function selection 1 Linear motor magnetic pole shift length Speed at the change of speed loop gain Voltage dead time compensation Overshooting compensation 1 Torque offset

II - 112

7.

SERVO PARAMETERS

Parameter SV033 SV034 SV035 SV036 SV037 SV038 SV039 SV040 SV041 SV042 SV043 SV044 SV045 SV046 SV047 SV048 SV049 SV050 SV051 SV052 SV053 SV054 SV055 SV056 SV057 SV058 SV059 SV060 SV061 SV062 SV063 SV064 SV065 Servo function selection 2 Servo function selection 3 Servo function selection 4 Regenerative resistor type Load inertia scale Notch filter frequency 1 Lost motion compensation timing Non-sensitive band in feed forward control Lost motion compensation 2 Overshooting compensation 2 Disturbance observer filter frequency Disturbance observer gain Frictional torque Notch filter frequency 2 Inductive voltage compensation gain Vertical axis drop prevention time Position loop gain 1 in spindle synchronous control Position loop gain 2 in spindle synchronous control Dual feedback control time constant Dual feedback control non-sensitive band Excessive error detection width in special control Overrun detection width in closed loop control Max. gate off delay time after emergency stop Deceleration time constant at emergency stop SHG control gain SHG control gain in spindle synchronous control Collision detection torque estimating gain Collision detection level D/A output channel 1 data No. D/A output channel 2 data No. D/A output channel 1 output scale D/A output channel 2 output scale Tool end compensation spring constant

Corresponding model MDS-C1-Vx MDS-C1-Vx MDS-B-SVJ2 (High-gain) (Standard) (MDS-B-Vx4) (MDS-B-Vx)

II - 113

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

7.1 MDS-B-SVJ2
(1) Details for servo parameters For parameters marked with a (PR) in the table, turn the NC power OFF after setting. After the power is turned ON again, the parameter is validated.

! CAUTION
!

In the explanation on bits, set all bits not used, including blank bits, to 0. Items Details Setting range

No. 2201 SV001 (PR) PC1 2202 SV002 (PR) PC2 2203 SV003 PGN1

Motor side gear Set the motor side and machine side gear ratio. 1 to 32767 ratio For the rotary axis, set the total deceleration (acceleration) ratio. Machine side 1 to 32767 Even if the gear ratio is within the setting range, the gear ratio electronic gears may overflow and cause an alarm. Position loop gain 1 Set the position loop gain. The standard setting is 33. The higher the setting value is, the more precisely the command can be followed and the shorter the positioning time gets, however, note that a bigger shock is applied to the machine during acceleration/deceleration. When using the SHG control, also set SV004 (PGN2) and SV057 (SHGC). When using the SHG control, also set SV003 (PGN1) and SV057 (SHGC). When not using the SHG control, set to 0. 1 to 200 (rad/s)

2204 SV004 PGN2 2205 SV005 VGN1

Position loop gain 2 Speed loop gain

0 to 999 (rad/s)

Set the speed loop gain. 1 to 999 Set this according to the load inertia size. The higher the setting value is, the more accurate the control will be, however, vibration tends to occur. If vibration occurs, adjust by lowering by 20 to 30%. The value should be determined to be 70 to 80% of the value at the time when the vibration stops. Not used. Set to 0. Not used. Set to 0. 0 0 1 to 9999

2206 2207 2208 SV008 VIA Speed loop lead compensation

Set the gain of the speed loop integration control. The standard setting is 1364. During the SHG control, the standard setting is 1900. Adjust the value by increasing/decreasing it by about 100 at a time. Raise this value to improve contour tracking precision in high-speed cutting. Lower this value when the position droop vibrates (10 to 20Hz).

2209 SV009 IQA 2210 SV010 IDA 2211 SV011 IQG 2212 SV012 IDG

Current loop q axis lead compensation Current loop d axis lead compensation Current loop q axis gain Current loop d axis gain

Set the gain of current loop. 1 to 20480 As this setting is determined by the motors electrical characteristics, the setting is fixed for each type of motor. 1 to 20480 Set the standard values for all the parameters depending on each motor type. 1 to 2560 1 to 2560

II - 114

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No. 2213 SV013 ILMT

Items Current limit value

Details Set the normal current (torque) limit value. (Limit values for both + and - direction.) When the value is 500 (a standard setting), the maximum torque is determined by the specification of the motor.

Setting range 0 to 500 (Stall [rated] current %)

2214 SV014 ILMTsp

Current limit Set the current (torque) limit value in a special value in special control (initial absolute position setting, stopper control control, etc). (Limit values for both of the + and directions.) Set to 500 when not using. Acceleration rate feed forward gain

0 to 500 (Stall [rated] current %)

2215 SV015 FFC

When a relative error in the synchronous control is 0 to 999 large, apply this parameter to the axis that is (%) delaying. The standard setting value is 0. For the SHG control, set to 100. To adjust a relative error in acceleration/ deceleration, increase the value by 50 to 100 at a time. Set this when the protrusion (that occurs due to the non-sensitive band by friction, torsion, backlash, etc) at quadrant change is too large. This compensates the torque at quadrant change. This is valid only when the lost motion compensation (SV027 (SSF1/lmc)) is selected. Type 1: When SV027 (SSF1)/ bit9, 8 (lmc)=01 Set the compensation amount based on the motor torque before the quadrant change. The standard setting is 100. Setting to 0 means the compensation amount is zero. Normally, use Type 2. -1 to 200 (%)

2216 SV016 LMC1

Lost motion compensation 1

Type 2: When SV027 (SSF1)/ bit9, 8 (lmc)=10 -1 to 100 Set the compensation amount based on the stall (Stall [rated] (rated) current of the motor. current %) The standard setting is double of the friction torque. Setting to 0 means the compensation amount is zero. When you wish different compensation amount depending on the direction When SV041 (LMC2) is 0, compensate with the value of SV016 (LMC1) in both of the + and -directions. If you wish to change the compensation amount depending on the command direction, set this and SV041 (LMC2). (SV016: + direction, SV041: direction. However, the directions may be opposite depending on other settings.) When -1 is set, the compensation wont be performed in the direction of the command.

II - 115

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No. 2217 (PR)

Items SV017 Servo SPEC specification selection F 7 abs bit 0 1 2 3 4 5 E 6

Details D C 5 vdir 4

B 3 mc

A 2

Setting range 9 8 1 0 dmk

Meaning when 0 is set Deceleration control stop dmk (SVJ2 standard)

Meaning when 1 is set Dynamic brake stop

mc Contactor control output invalid Contactor control output valid HA053N to HA33N motor vdir Detector installation position standard (A, C) HA053N to HA33N motor Detector installation position 90 degrees (B, D)

6 7 8 9 A B C D E F 2218 (PR) 2219 (PR) SV018 Ball screw PIT pitch SV019 Position RNG1 detector resolution

abs Incremental control

Absolute position control

(Note) Set to 0 for bits with no particular description. Set the ball screw pitch. Set to 360 for the rotary axis. For both parameters, set the number of pulses per one revolution of the motor detector. Motor model name 2220 (PR) SV020 Speed RNG2 detector resolution HC*-E42/A42/A47, HC*R-E42/A42/A47 HA*N-E42/A42 HC*-E33/A33, HC*R-E33/A33 HA*N-E33/A33 HC-SF, HC-RF HA-FF, HC-MF 2221 Setting value SV019 SV020 100 25 16 8 100 25 16 8 1 to 32767 (mm/rev) 8 to 100 (kp/rev)

SV021 Overload Set the detection time constant of Overload 1 (Alarm 50). 1 to 300 OLT detection time Set to 60 as a standard. (For machine tool builder (s) constant adjustment.) SV022 Overload OLL detection level Set the current detection level of Overload 1 (Alarm 50) in 50 to 180 respect to the stall (rated) current. Set to 150 as a (Stall [rated] standard. (For machine tool builder adjustment.) current %)

2222

II - 116

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No. 2223 SV023 OD1

Items

Details

Setting range 0 to 32767 (mm)

Excessive Set the excessive error detection width when servo ON. error <Standard setting value> detection Rapid traverse rate width during (mm/min) servo ON OD1=OD2= /2 (mm) 60*PGN1 When 0 is set, the excessive error detection will not be performed.

2224 SV024 INP

In-position detection width

Set the in-position detection width. Set the accuracy required for the machine. The lower the setting is, the higher the positioning accuracy gets, however, the cycle time (setting time) becomes longer. The standard setting is 50.

0 to 32767 (m)

II - 117

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No. 2225 (PR) SV025 MTYP

Items Motor/ Detector type F 7 E pen 6

Details D C 5 4 mtyp

B 3

A ent 2

Setting range 9 8 1 0

Explanation Set the motor type. Set1 0x 1x 2x 3x 4x 5x 6x ting 2 x0 HA40N 3 mtyp x1 HA80N 4 x2 HA100N 5 x3 HA200N 6 x4 7 x5 x6 x7 x8 x9 xA xB xC xD xE xF 0 Setting x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC HC-MF053 xD HC-MF13 xE HC-MF23 xF 9x HC-MF43 HC-MF73 Ax Bx Cx

bit

7x HA-FF43 HA-FF63

8x HA43N HA83N HA103N

HA93N HA-FF053 HA-FF13 HA-FF23 HA-FF33 Dx HA053N HA13N HA23N HA33N Ex Fx

HC52 or HC53 or HC-SF52 HC-SF53 HC102 or HC103 or HC-SF102 HC-SF103 HC152 or HC153 or HC-SF152 HC-SF153 HC202 or HC203 or HC-SF202 HC-SF203 HC352 or HC-SF353 HC-SF352

HC103R or HC-RF103 HC153R or HC-RF153 HC203R or HC-RF203

(To be continued to the next page)

II - 118

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No.

Items

Details (Continued from the previous page) bit Explanation Set the speed detector type. 8 Set to 2. 9 ent A B Set the position detector type. C Set to 2. D pen E F

Setting range

2226 SV026 OD2

Excessive error detection width during servo OFF Servo function selection 1

2227

SV027 SSF1

Set the excessive error detection width when servo ON. 0 to 32767 For the standard setting, refer to the explanation of (mm) SV023 (OD1). When 0 is set, the excessive error detection will not be performed. F E D C B A 9 8 aflt zrn2 ovs lmc 7 6 5 vfct bit Meaning when 0 is set 4 3 2 1 0 zup

0 zup Vertical axis lift-up control stop 1 2 3

Meaning when 1 is set Vertical axis lift-up control start

Set the jitter compensation No. of compensation pulses with a vfct binary. 5 00: Jitter compensation invalid 01: Jitter compensation 1 pulse 10: Jitter compensation 2 pulses 11: Jitter compensation 3 pulses 6 7 Set the compensation amount with SV016 (LMC1) and SV041 8 lmc (LMC2). 9 00: Lost motion compensation stop 01: Lost motion compensation type 1 10: Lost motion compensation type 2 11: Setting prohibited Set the compensation amount with SV031 (OVS1) and SV042 A ovs (OVS2). B 00: Overshooting compensation stop 01: Overshooting compensation type 1 10: Overshooting compensation type 2 11: Setting prohibited C D E zrn2 Set to 1. F aflt Adoptive filter stops Adoptive filter starts 4 (Note) Set to 0 for bits with no particular description. 2228 SV028 2229 SV029 Not used. Set to 0. Not used. Set to 0. 0 0

II - 119

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No. 2230 SV030 IVC

Items Voltage dead time compensation

Details

Setting range

When 100% is set, the voltage equivalent to the logical 0 to 200 non-energized time will be compensated. (%) Adjust in increments of 10% from the default value 100%. If increased too much, vibration or vibration noise may be generated. When not using, set to 0. Set this if overshooting occurs during positioning. This compensates the motor torque during positioning. This is valid only when the overshooting compensation SV027 (SSF1/ovs) is selected. Type 1: When SV027 (SSF1)/ bit11, 10 (ovs)=01 Set the compensation amount based on the motors stall (rated) current. Increase by 1% and determine the amount that overshooting doesnt occur. In Type 1, compensation during the feed forward control during circular cutting wont be performed. Type 2: When SV027 (SSF1)/ bit11, 10 (ovs)=10 Use this if you perform the overshooting compensation during the feed forward control during circular cutting. The setting method is the same in Type 1. When you wish different compensation amount depending on the direction When SV042 (OVS2) is 0, compensate with the value of SV031 (OVS1) in both of the + and -directions. If you wish to change the compensation amount depending on the command direction, set this and SV042 (OVS2). (SV031: + direction, SV042: - direction. However, the directions may be opposite depending on other settings.) When -1 is set, the compensation wont be performed in the direction of the command. -1 to 100 (Stall [rated] current %)

2231 SV031 OVS1

Overshooting compensation 1

2232 SV032 TOF

Torque offset

Set the unbalance torque of vertical axis and inclined axis.

-100 to 100 (Stall [rated] current %)

II - 120

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No. 2233 SV033 SSF2

Items Servo function selection 2 F 7 E 6

Details D C 5 fhz2 4

B 3

A afs 2 nfd

Setting range 9 8 1 0

bit Meaning when 0 is set Meaning when 1 is set 0 Set the filter depth for Notch filter (SV038: FHz1). 1 The control is stabilized by making the filter shallower. 2 nfd Value 0 2 4 6 8 A C E Depth Infntly 3 -18.1 -12.0 -8.5 -6.0 -4.1 -2.5 -1.2 (dB) deep Deep Shallow 4 Set the operation frequency of Notch filter 2. fhz2 5 00: No operation 01:2250Hz 10:1125Hz 11:750Hz 6 7 Set the vibration sensitivity of the adaptive filter. If the filter depth 8 is not deep enough (generally 70% or more) and the vibration 9 afs cannot be sufficiently eliminated, raise the value. A B C D E F (Note) Set to 0 for bits with no particular description.

II - 121

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No. 2234 SV034 SSF3

Items Servo function selection 3 F 7 daf2 bit E 6 daf1

Details D C 5 dac2 4 dac1

B 3

A 2 mon

Setting range 9 8 1 0

Meaning when 0 is set Meaning when 1 is set NC servo monitor MAX current display data changeover Set1 MAX current 1 MAX current 2 ting Max. current command Max. current command mon 2 0 value when power is value for one second (%) turned ON (%) Max. current command Max. current FB value for 3 1 value for one second (%) one second (%) Max. current FB value Max. current FB value for 2 when power is turned ON one second (%) (%) 3 Load inertia rate (%) Adaptive filter operation Adaptive filter operation 4 frequency (Hz) gain (%) PN bus voltage (V) Regenerative operation 5 frequency monitor (The number of times/sec) Estimated max. torque Max. current FB value for 6 for one second (%) one second (%) Estimated max. torque Max. disturbance torque 7 for one second (%) for two seconds (%) 8 to F Setting prohibited 0 4 5 6 7 8 9 A B C D E F dac1 dac2 daf1 daf2 D/A output ch.1 overflow setting D/A output ch.2 overflow setting D/A output ch.1 no filter D/A output ch.2 no filter D/A output ch.1 clamp setting D/A output ch.2 clamp setting D/A output ch.1 filter setting D/A output ch.2 filter setting

(Note) Set to 0 for bits with no particular description.

II - 122

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No. 2235 SV035 SSF4

Items Servo function selection 4 F cl2n 7 E 6

Details D C clG1 5 4

B 3

A 2

Setting range 9 8 1 0

bit 0 1 2 3 4 5 6 7 8 9 A B C D

Meaning when 0 is set

Meaning when 1 is set

Collision detection method 1 Set the collision detection level during cutting feed (G1). clG1 The G1 collision detection level=SV060*clG1. When clG1=0, the collision detection method 1 during cutting feed E wont function. Collision detection method 2 Collision detection method 2 F cl2n valid invalid (Note) Set to 0 for bits with no particular description.

II - 123

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No. 2236 (PR) SV036 PTYP

Items Regenerative resistor type F 7 E amp 6 emgx bit 0 1 2 3 4

Details D C 5 4

B 3

A rtyp 2

Setting range 9 8 1 0

Explanation Always set to 0(0000).

Set the external emergency stop function. (Setting is prohibited for values with no description.) Set5 emgx Explanation ting 6 0 External emergency stop invalid 7 4 External emergency stop valid 8 9 A B Set the regenerative resistor type. SetExplanation ting rtyp Drive unit standard built-in resistor (SVJ2-01 0 doesnt have a built-in resistor) 1 Setting prohibited 2 MR-RB032 3 MR-RB12 or GZG200W390HMK MR-RB32 or GZG200W1200HMK: 3 units 4 connected in parallel MR-RB30 or GZG200W390HMK: 3 units 5 connected in parallel MR-RB50 or GZG300W390HMK: 3 units 6 connected in parallel 7 to F Setting prohibited Always set to 0(0000). amp

C D E F

II - 124

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No.

Items

Details Set the motor inertia + motor axis conversion load inertia in respect to the motor inertia. SV037 (JL) = Jl+Jm Jm *100

Setting range 0 to 5000 (%)

2237 SV037 JL Load inertia scale

Jm: Motor inertia Jl: Motor axis conversion load inertia 2238 SV038 FHz1 2239 SV039 LMCD 2240 SV040 LMCT Notch filter frequency 1 Lost motion compensation timing Set the vibration frequency to suppress if machine vibration occurs. (Valid at 72 or more) When not using, set to 0. Set this when the lost motion compensation timing doest not match. Adjust by increasing the value by 10 at a time. 0 to 3000 (Hz) 0 to 2000 (ms) 0 to 100 (m)

Non-sensitive Set the non-sensitive bad of the lost motion band in feed compensation and overshooting compensation forward control during the feed forward control. When 0 is set, the actual value that will be set is 2m. Adjust by increasing by 1m. Lost motion compensation 2 Overshooting compensation 2 Disturbance observer filter frequency Set this with SV016 (LMC1) only when you wish to set the lost motion compensation amount to be different depending on the command directions. Set to 0 as a standard. Set this with SV031 (OVS1) only when you wish to set the overshooting compensation amount to be different depending on the command directions. Set to 0 as a standard.

2241 SV041 LMC2

-1 to 200 (Stall [rated] current %) -1 to 100 (Stall [rated] current %)

2242 SV042 OVS2

2243 SV043 OBS1

Set the disturbance observer filter band. 0 to 1000 The standard setting is 300. Lower the setting by (rad/s) 50 at a time if vibration occurs. To use the disturbance observer, also set SV037 (JL) and SV044 (OBS2). When not using, set to 0. Set the disturbance observer gain. The standard 0 to 1000 setting is 100 to 300. (%) To use the disturbance observer, also set SV037 (JL) and SV043 (OBS1). When not using, set to 0. Set the frictional torque when using the collision detection function. Not used. Set to 0. 0 to 100 (Stall [rated] current %) 0

2244 SV044 OBS2

Disturbance observer gain

2245 SV045 TRUB 2246 SV046 2247 SV047 EC

Frictional torque

Inductive voltage compensation gain

Set the inductive voltage compensation gain. Set to 0 to 200 100 as a standard. (%) If the current FB peak exceeds the current command peak, lower the gain.

2248 SV048 EMGrt

Vertical axis Input a length of time to prevent the vertical axis from 0 to 2000 drop prevention dropping by delaying Ready OFF until the brake (ms) time works when the emergency stop occurs. Increase the setting by 100ms at a time and set the value where the axis does not drop.

II - 125

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No. 2249 SV049 PGN1sp

Items Position loop gain 1 in spindle synchronous control

Details Set the position loop gain during the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). Set the same value as the value of the spindle parameter, position loop gain in synchronous control. When performing the SHG control, set this with SV050 (PGN2sp) and SV058 (SHGCsp).

Setting range 1 to 200 (rad/s)

2250 PGN2sp

Position loop gain 2 in spindle synchronous control

Set this with SV049 (PGN1sp) and SV058 0 to 999 (SHGCsp) if you wish to perform the SHG control in (rad/s) the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). When not performing the SHG control, set to 0. Not used. Set to 0. Not used. Set to 0. 0 0 0 to 32767 (mm)

2251 SV051 2252 SV052 2253 SV053 OD3 Excessive error detection width in special control

Set the excessive error detection width when servo ON in a special control (initial absolute position setting, stopper control, etc.). If 0 is set, excessive error detection wont be performed when servo ON during a special control. Not used. Set to 0. Not used. Set to 0.

2254 SV054 2255 SV055 2256 SV056 EMGt Deceleration time constant at emergency stop SHG control gain SHG control gain in spindle synchronous control Collision detection torque estimating gain

0 0 0 to 5000 (ms)

Set the time constant used for the deceleration control at emergency stop. Set a length of time that takes from rapid traverse rate (rapid) to stopping. Normally, set the same value as the rapid traverse acceleration/deceleration time constant.

2257 SV057 SHGC 2258 SV058 SHGCsp

When performing the SHG control, set this with S003 0 to 999 (PGN1) and SV004 (PGN2). (rad/s) When not performing the SHG control, set to 0. Set this with SV049 (PGN1sp) and SV050 (PGN2sp) 0 to 999 if you wish to perform the SHG control in the spindle (rad/s) synchronous control (synchronous tapping, synchronous control with spindle/C axis). When not performing the SHG control, set to 0. To use the collision detection function, set the torque 0 to 5000 estimating gain. In the case of MDS-B-SVJ2, the (%) value is the same as the load inertia ratio that includes the motor inertia. (=SV037:JL) If acceleration/deceleration is performed after setting SV034.mon=3 and SV060=0, the load inertia ratio will be displayed on the NC monitor screen. 0 to 200 (Stall [rated] current %)

2259 SV059 TCNV

2260 SV060 TLMT

Collision When using the collision detection function, set the detection level collision detection level during the G0 feeding. If 0 is set, none of the collision detection function will work.

II - 126

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

No. 2261 SV061 DA1NO 2262 SV062 DA2NO 2263 SV063 DA1MPY 2264 SV064 DA2MPY 2265 SV065

Items D/A output channel 1 data No. D/A output channel 2 data No. D/A output channel 1 output scale D/A output channel 2 output scale

Details Input the data number you wish to output to D/A output channel.

Setting range 0 to 102

When 0 is set, output is done with the standard -32768 to output unit. 32767 Set other than 0 when you wish to change the unit. Set the scale with a 1/256 unit. When 256 is set, (Unit: 1/256) the output unit will be the same as the standard output unit. Not used. Set to 0. 0

II - 127

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

(2) Initial setting value (a) HC**/HC**R series HC 52 06 33 0 50 0 0 1364 8192 8192 512 512 500 500 0 0 0000 60 150 50 22B0 4000 0 0 0 0 0 HC 102* 07 33 0 80 0 0 1364 4096 4096 256 256 500 500 0 0 0000 60 150 50 22B1 4000 0 0 0 0 0 HC 102 10 33 0 50 0 0 1364 8192 8192 384 384 500 500 0 0 0000 60 150 50 22B1 4000 0 0 0 0 0 HC 152* 10 33 0 80 0 0 1364 4096 4096 256 256 500 500 0 0 0000 60 150 50 22B2 4000 0 0 0 0 0 HC 152 20 33 0 50 0 0 1364 8192 8192 384 384 500 500 0 0 0000 60 150 50 22B2 4000 0 0 0 0 0 HC 202* 10 33 0 115 0 0 1364 2048 2048 256 256 500 500 0 0 0000 60 150 50 22B3 4000 0 0 0 0 0 HC 202 20 33 0 80 0 0 1364 4096 4096 384 384 500 500 0 0 0000 60 150 50 22B3 4000 0 0 0 0 0 HC 352* 20 33 0 130 0 0 1364 2048 2048 256 256 500 500 0 0 0000 60 150 50 22B4 4000 0 0 0 0 0

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 SV007 SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 SV030 IVC SV031 OVS1 SV032 TOF

II - 128

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 SV052 SV053 OD3 SV054 SV055 SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065

HC 52 06 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 102* 07 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 102 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 152* 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 152 20 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 202* 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 202 20 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 352* 20 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 129

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 SV007 SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 SV030 IVC SV031 OVS1 SV032 TOF

HC 53 06 33 0 80 0 0 1364 4096 4096 256 256 500 500 0 0 0000 60 150 50 22C0 4000 0 0 0 0 0

HC 103 10 33 0 80 0 0 1364 4096 4096 256 256 500 500 0 0 0000 60 150 50 22C1 4000 0 0 0 0 0

HC 153 20 33 0 80 0 0 1364 4096 4096 256 256 500 500 0 0 0000 60 150 50 22C2 4000 0 0 0 0 0

HC 203* 20 33 0 100 0 0 1364 2048 2048 200 200 500 500 0 0 0000 60 150 50 22C3 4000 0 0 0 0 0

HC 103R 10 33 0 10 0 0 1364 8192 8192 384 384 500 500 0 0 0000 60 150 50 22E1 4000 0 0 0 0 0

HC 153R 10 33 0 10 0 0 1364 8192 8192 384 384 500 500 0 0 0000 60 150 50 22E2 4000 0 0 0 0 0

HC 203R 20 33 0 10 0 0 1364 8192 8192 256 256 500 500 0 0 0000 60 150 50 22E3 4000 0 0 0 0 0

II - 130

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 SV052 SV053 OD3 SV054 SV055 SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065

HC 53 06 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 103 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 153 20 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 203* 20 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 103R 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 153R 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 203R 20 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 131

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

(b) HA**N series HA 40N 06 33 0 90 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 50 2200 4000 0 0 0 0 0 HA 80N 10 33 0 150 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 50 2201 4000 0 0 0 0 0 HA HA HA 100N 200N* 053N 20 33 0 150 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 50 2202 4000 0 0 0 0 0 20 33 0 220 0 0 1364 2048 2048 200 200 500 500 0 0 0000 60 150 50 2203 4000 0 0 0 0 0 01 33 0 35 0 0 1364 2048 2048 256 256 500 500 0 0 0000 60 150 50 228C 4000 0 0 0 0 0 HA 13N 01 33 0 35 0 0 1364 2048 2048 256 256 500 500 0 0 0000 60 150 50 228D 4000 0 0 0 0 0 HA 23N 03 33 0 35 0 0 1364 2048 2048 256 256 500 500 0 0 0000 60 150 50 228E 4000 0 0 0 0 0 HA 33N 03 33 0 35 0 0 1364 2048 2048 256 256 500 500 0 0 0000 60 150 50 228F 4000 0 0 0 0 0 HA 43N 06 33 0 120 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 50 2280 4000 0 0 0 0 0 HA 83N 10 33 0 150 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 50 2281 4000 0 0 0 0 0 HA 103N* 20 33 0 180 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 50 2282 4000 0 0 0 0 0

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 SV007 SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 SV030 IVC SV031 OVS1 SV032 TOF

II - 132

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 SV052 SV053 OD3 SV054 SV055 SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065

HA 40N 06 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 80N 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA HA HA 100N 200N* 053N 20 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 20 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 01 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 13N 01 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 23N 03 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 33N 03 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 43N 06 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 83N 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 103N* 20 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 133

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

(c) HC-SF series HC-SF HC-SF HC-SF HC-SF HC-SF HC-SF HC-SF HC-SF HC-SF HC-SF 52 102 152 202 352 53 103 153 203 353 06 33 0 80 0 0 1364 8192 8192 500 500 500 500 0 0 0000 16 16 60 150 50 22B0 4000 0 0 0 0 0 07 33 0 80 0 0 1364 4096 4096 300 300 500 500 0 0 0000 16 16 60 150 50 22B1 4000 0 0 0 0 0 10 33 0 80 0 0 1364 4096 4096 300 300 500 500 0 0 0000 16 16 60 150 50 22B2 4000 0 0 0 0 0 10 33 0 120 0 0 1364 2048 2048 300 300 500 500 0 0 0000 16 16 60 150 50 22B3 4000 0 0 0 0 0 20 33 0 130 0 0 1364 2048 2048 250 250 500 500 0 0 0000 16 16 60 150 50 22B4 4000 0 0 0 0 0 06 33 0 90 0 0 1364 4096 4096 250 250 500 500 0 0 0000 16 16 60 150 50 22C0 4000 0 0 0 0 0 07 33 0 90 0 0 1364 4096 4096 250 250 500 500 0 0 0000 16 16 60 150 50 22C1 4000 0 0 0 0 0 10 33 0 130 0 0 1364 2048 2048 200 200 500 500 0 0 0000 16 16 60 150 50 22C2 4000 0 0 0 0 0 10 33 0 180 0 0 1364 2048 2048 200 200 500 500 0 0 0000 16 16 60 150 50 22C3 4000 0 0 0 0 0 20 33 0 180 0 0 1364 2048 2048 200 200 500 500 0 0 0000 16 16 60 150 50 22C4 4000 0 0 0 0 0

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 SV007 SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 SV030 IVC SV031 OVS1 SV032 TOF

II - 134

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 SV052 SV053 OD3 SV054 SV055 SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065

HC-SF HC-SF HC-SF HC-SF HC-SF HC-SF HC-SF HC-SF HC-SF HC-SF 52 102 152 202 352 53 103 153 203 353 06 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 07 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 20 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 06 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 07 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 20 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 135

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

(d) HC-RF/HA-FF series HC-RF 103 10 33 0 10 0 0 1364 8192 8192 384 384 500 500 0 0 0000 16 16 60 150 50 22E1 4000 0 0 0 0 0 HC-RF 153 10 33 0 10 0 0 1364 8192 8192 384 384 500 500 0 0 0000 16 16 60 150 50 22E2 4000 0 0 0 0 0 HC-RF 203 20 33 0 10 0 0 1364 8192 8192 256 256 500 500 0 0 0000 16 16 60 150 50 22E3 4000 0 0 0 0 0 HA-FF 053 01 33 0 10 0 0 1364 8192 8192 500 500 500 500 0 0 0000 8 8 60 150 50 227C 4000 0 0 0 0 0 HA-FF 13 01 33 0 13 0 0 1364 4096 4096 300 300 500 500 0 0 0000 8 8 60 150 50 227D 4000 0 0 0 0 0 HA-FF 23 03 33 0 13 0 0 1364 4096 4096 700 700 500 500 0 0 0000 8 8 60 150 50 227E 4000 0 0 0 0 0 HA-FF 33 03 33 0 18 0 0 1364 4096 4096 500 500 500 500 0 0 0000 8 8 60 150 50 227F 4000 0 0 0 0 0 HA-FF 43 04 33 0 20 0 0 1364 4096 4096 700 700 500 500 0 0 0000 8 8 60 150 50 2270 4000 0 0 0 0 0 HA-FF 63 06 33 0 20 0 0 1364 4096 4096 700 700 500 500 0 0 0000 8 8 60 150 50 2271 4000 0 0 0 0 0

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 SV007 SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 SV030 IVC SV031 OVS1 SV032 TOF

II - 136

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 SV052 SV053 OD3 SV054 SV055 SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065

HC-RF 103 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC-RF 153 10 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC-RF 203 20 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA-FF 053 01 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA-FF 13 01 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA-FF 23 03 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA-FF 33 03 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA-FF 43 04 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA-FF 63 06 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 137

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

(e) HC-MF series HC-MF 053 01 33 0 6 0 0 1364 4096 4096 200 200 500 500 0 0 0000 8 8 60 150 50 229C 4000 0 0 0 0 0 HC-MF 13 01 33 0 6 0 0 1364 4096 4096 300 300 500 500 0 0 0000 8 8 60 150 50 229D 4000 0 0 0 0 0 HC-MF 23 03 33 0 6 0 0 1364 4096 4096 400 400 500 500 0 0 0000 8 8 60 150 50 229E 4000 0 0 0 0 0 HC-MF 43 04 33 0 6 0 0 1364 4096 4096 300 300 500 500 0 0 0000 8 8 60 150 50 2290 4000 0 0 0 0 0 HC-MF 73 07 33 0 8 0 0 1364 4096 4096 300 300 500 500 0 0 0000 8 8 60 150 50 2291 4000 0 0 0 0 0

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 SV007 SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 SV030 IVC SV031 OVS1 SV032 TOF

II - 138

7.

SERVO PARAMETERS 7.1 MDS-B-SVJ2

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 SV052 SV053 OD3 SV054 SV055 SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065

HC-MF 053 01 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC-MF 13 01 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC-MF 23 03 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC-MF 43 04 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC-MF 73 07 0 0 0 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 139

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

7.2 MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

(1) Details for servo parameters For parameters marked with a (PR) in the table, turn the NC power OFF after setting. After the power is turned ON again, the parameter is validated.

! CAUTION
!

In the explanation on bits, set all bits not used, including blank bits, to 0. Items Details Setting range

No. 2201 SV001 (PR) PC1 2202 SV002 (PR) PC2 2203 SV003 PGN1

Motor side gear Set the motor side and machine side gear ratio. 1 to 32767 ratio For the rotary axis, set the total deceleration (acceleration) ratio. Machine side 1 to 32767 Even if the gear ratio is within the setting range, the gear ratio electronic gears may overflow and cause an alarm. Position loop gain 1 Set the position loop gain. The standard setting is 33. The higher the setting value is, the more precisely the command can be followed and the shorter the positioning time gets, however, note that a bigger shock is applied to the machine during acceleration/deceleration. When using the SHG control, also set SV004 (PGN2) and SV057 (SHGC). (If 201 or bigger is set, the SHG control cannot be used.) When using the SHG control, also set SV003 (PGN1) and SV057 (SHGC). When not using the SHG control, set to 0. 1 to 200 (In case of MDS-B-Vx4, 1 to 400) (rad/s)

2204 SV004 PGN2 2205 SV005 VGN1

Position loop gain 2 Speed loop gain 1

0 to 999 (rad/s)

Set the speed loop gain. 1 to 999 Set this according to the load inertia size. The higher the setting value is, the more accurate the control will be, however, vibration tends to occur. If vibration occurs, adjust by lowering by 20 to 30%. The value should be determined to be 70 to 80% of the value at the time when the vibration stops. If the noise is bothersome at high speed during rapid -1000 to 1000 traverse, etc, lower the speed loop gain. As in the right figure, set the speed loop gain of the speed 1.2 times as fast as the motors rated speed, and use this with SV029 (VCS). When not using, set to 0.

2206 SV006 VGN2

Speed loop gain 2

VGN1 VGN2 0 VCS VLMT (Rated speed*1.2)

II - 140

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2207 SV007 VIL

Items Speed loop delay compensation

Details

Setting range

Set this when the limit cycle occurs in the full-closed 0 to 32767 loop, or overshooting occurs in positioning. Select the control method with SV027 (SSF1)/bit1, 0 (vcnt). Normally, use Changeover type 2. When you set this parameter, make sure to set the torque offset (SV032 (TOF)). When not using, set to 0. No changeover When SV027 (SSF1)/ bit1, 0 (vcnt)=00 The delay compensation control is always valid. Changeover type 1 When SV027 (SSF1)/ bit1, 0 (vcnt)=01 The delay compensation control works when the command from the NC is 0. Overshooting that occurs during pulse feeding can be suppressed. Changeover type 2 When SV027 (SSF1)/ bit1, 0 (vcnt)=10 The delay compensation control works when the command from the NC is 0 and the position droop is 0. Overshooting or the limit cycle that occurs during pulse feeding or positioning can be suppressed.

2208 SV008 VIA

Speed loop lead compensation

Set the gain of the speed loop integration control. The standard setting is 1364. During the SHG control, the standard setting is 1900. Adjust the value by increasing/decreasing it by about 100 at a time. Raise this value to improve contour tracking precision in high-speed cutting. Lower this value when the position droop vibrates (10 to 20Hz).

1 to 9999

2209 SV009 IQA 2210 SV010 IDA 2211 SV011 IQG 2212 SV012 IDG 2213 SV013 ILMT

Current loop q axis lead compensation Current loop d axis lead compensation Current loop q axis gain Current loop d axis gain Current limit value

Set the gain of current loop. 1 to 20480 As this setting is determined by the motors electrical characteristics, the setting is fixed for each type of motor. Set the standard values for all the parameters depending on each motor type. 1 to 4096 (In case of MDS-B-Vx4, 1 to 8192) Set the normal current (torque) limit value. (Limit values for both + and - direction.) When the value is 500 (a standard setting), the maximum torque is determined by the specification of the motor. 0 to 999 (Stall [rated] current %)

2214 SV014 ILMTsp

Current limit Set the current (torque) limit value in a special value in special control (initial absolute position setting, stopper control control, etc). (Limit values for both of the + and directions.) Set to 500 when not using.

0 to 999 (Stall [rated] current %)

II - 141

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No.

Items

Details

Setting range

2215 SV015 Acceleration FFC rate feed forward gain

When a relative error in the synchronous control is large, 0 to 999(%) apply this parameter to the axis that is delaying. The standard setting value is 0. For the SHG control, set to 100. To adjust a relative error in acceleration/deceleration, increase the value by 50 to 100 at a time. Set this when the protrusion (that occurs due to the non-sensitive band by friction, torsion, backlash, etc) at quadrant change is too large. This compensates the torque at quadrant change. This is valid only when the lost motion compensation (SV027 (SSF1/lmc)) is selected. Type 1: When SV027 (SSF1)/ bit9, 8 (lmc)=01 -1 to 200 Set the compensation amount based on the motor torque (%) before the quadrant change. The standard setting is 100. Setting to 0 means the compensation amount is zero. Normally, use Type 2. Type 2: When SV027 (SSF1)/ bit9, 8 (lmc)=10 -1 to 100 Set the compensation amount based on the stall (rated) (Stall [rated] current of the motor. current %) The standard setting is double of the friction torque. Setting to 0 means the compensation amount is zero. When you wish different compensation amount depending on the direction When SV041 (LMC2) is 0, compensate with the value of SV016 (LMC1) in both of the + and -directions. If you wish to change the compensation amount depending on the command direction, set this and SV041 (LMC2). (SV016: + direction, SV041: - direction. However, the directions may be opposite depending on other settings.) When -1 is set, the compensation wont be performed in the direction of the command.

2216 SV016 Lost motion LMC1 compensation 1

II - 142

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2217 (PR)

Items SV017 Servo SPEC specification selection F 7 abs bit E spm 6

Details D C 5 vdir 4 fdir

B drvall 3 vfb

A drvup 2 seqh

Setting range 9 8 mpt3 mp 1 0 dfbx fdir2

Meaning when 1 is set Speed feedback reverse polarity Dual feedback control start READY/Servo ON time high 2 seqh READY/Servo ON time normal speed Speed feedback filter stop Speed feedback filter stop 3 vfb (2250Hz) Position feedback forward Position feedback reverse 4 fdir polarity polarity 5 vdir Standard setting HA motor (4 pole motor) Detector installation position 90 degrees (B, D) 6 7 abs Incremental control Absolute position control 8 mp MP scale 360P (2mm pitch) MP scale 720P (1mm pitch) MP scale ABS detection type 1, MP scale ABS detection type 3 9 mpt3 2 A drvup Standard setting Possible to connect a drive unit whose capacity is 1 rank higher/lower than the standard one. B drvall Setting for normal use Possible to connect a drive unit with any capacity. 0 : Setting for normal use C 1 : When using the S type drive unit (Only in the case of D spm MDS-C1-Vx) E 2 to F : Setting prohibited F (Note 1) Set to 0 for bits with no particular description. (Note 2) bit3 (vfb) is only for MDS-C1-Vx.

Meaning when 0 is set Speed feedback forward 0 fdir2 polarity 1 dfbx Dual feedback control stop

II - 143

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2218 (PR) 2219 (PR) SV018 PIT SV019 RNG1

Items Ball screw pitch Position detector resolution

Details Set the ball screw pitch. Set to 360 for the rotary axis. In the case of the semi-closed loop control Set the same value as SV020 (RNG2). (Refer to the explanation of SV020.) In the case of the semi-closed loop control Set the same value as SV020 (RNG2). (Refer to the explanation of SV020.) Detector model name OHE25K-ET, OHA25K-ET OSE104-ET, OSA104-ET OSE105-ET, OSA105-ET RCN723 (Heidenhain) Relative position detection scale AT41 (Mitsutoyo) FME type, FLE type (Futaba) MP type (Mitsubishi Heavy Industries) AT342 (Mitsutoyo) AT343 (Mitsutoyo) LC191M (Heidenhain) Resolution 100,000(p/rev) 100,000(p/rev) 1,000,000(p/rev) 8,000,000(p/rev) Refer to specification manual for each detector 1 (m/p) Refer to specification manual for each detector Refer to specification manual for each detector 0.5 (m/p) 0.05 (m/p) Refer to specification manual for each detector Refer to specification manual for each detector

Setting range 1 to 32767 (mm/rev) 1 to 9999 (kp/rev) 1 to 9999 (kp/pit)

SV019 setting 100 100 1000 8000 PIT/Resolution (m)

The same as SV018 (PIT) PIT/Resolution (m)

PIT/Resolution (m)

Twice as big as SV018 (PIT) 20 times as big as SV018 (PIT) PIT/Resolution (m)

LC491M (Heidenhain)

PIT/Resolution (m)

2220 (PR)

SV020 Speed RNG2 detector resolution

Set the number of pulses per one revolution of the motor 1 to 9999 end detector. (kp/rev) Detector model name OSE104, OSA104 OSE105, OSA105 SV020 setting 100 1000

2221

SV021 Overload Set the detection time constant of Overload 1 (Alarm 50). 1 to 999 OLT detection Set to 60 as a standard. (For machine tool builder (s) time constant adjustment.) SV022 Overload OLL detection level Set the current detection level of Overload 1 (Alarm 50) in 110 to 500 respect to the stall (rated) current. Set to 150 as a (Stall [rated] standard. (For machine tool builder adjustment.) current %)

2222

II - 144

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2223 SV023 OD1

Items

Details

Setting range 0 to 32767 (mm)

Excessive Set the excessive error detection width when servo ON. error <Standard setting value> detection Rapid traverse rate width during (mm/min) servo ON OD1=OD2= /2 (mm) 60*PGN1 When 0 is set, the excessive error detection will not be performed.

2224 SV024 INP

In-position detection width

Set the in-position detection width. Set the accuracy required for the machine. The lower the setting is, the higher the positioning accuracy gets, however, the cycle time (setting time) becomes longer. The standard setting is 50.

0 to 32767 (m)

II - 145

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2225 (PR) SV025 MTYP

Items Motor /Detector type F 7 E pen 6

Details D C 5 4 mtyp

B 3

A ent 2

Setting range 9 8 1 0

bit 0 1 2

Explanation

Set the motor type. Set this along with SV017 (SPEC)/spm. 1) When SV017/spm=0 (Normal drive unit) Set0x 1x 2x 3x 3 ting x0 HA40N HA50L HA53L 4 mtyp x1 HA80N HA100L HA103L 5 x2 HA100N HA200L HA203L 6 x3 HA200N HA300L HA303L 7 x4 HA300N HA500L HA503L x5 HA700N x6 HA900N x7 HA-LH11K2 x8 HA-LH15K2 x9 xA HA150L HA153L xB xC xD HA-LF15K2 xE xF Setting x0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF 8x HA43N HA83N HA103N HA203N HA303N HA703N 9x Ax Bx HC52 HC102 HC152 HC202 HC352 HC452 HC702 HC902 Cx HC53 HC103 HC153 HC203 HC353 HC453 HC703

4x 5x 6x 7x

Dx

Ex HC103R HC153R HC203R HC353R HC503R

Fx

HA93N HA053N HA13N HA23N HA33N

(Continued to the next page)

II - 146

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No.

Items

Details (Continued from the previous page) bit Explanation

2) When SV017/spm=1 (S type drive unit) Set8x 9x Ax Bx Cx ting x0 x1 x2 x3 x4 HC353 x5 HC452 HC453 x6 HC702 x7 x8 x9 xA xB xC xD xE xF Dx

Setting range

Ex

Fx

Set the detector type. Set the position detector type for pen, and the speed detector type for ent. In the case of the semi-closed loop control, set the same value for A ent pen and ent. pen ent setting Detector model name B setting 0 0 OSE104 C pen 1 1 OSA104 D 2 2 OSE105, OSA105 E 3 3 F 4 Setting OHE25K-ET, OSE104-ET impossible 5 Setting OHA25K-ET, OSA104-ET impossible 6 Setting OSE105-ET, OSA105-ET, RCN723 impossible (Heidenhain) 7 Setting impossible 8 Setting Relative position detection scale, MP type impossible (Mitsubishi Heavy Industries) 9 Setting AT41 (Mitsutoyo), FME type, FLE type impossible (Futaba) A Setting AT342,AT343 (Mitsutoyo), impossible LC191M/491M (Heidenhain), MDS-B-HR B Setting impossible The setting of the slave axis in the C C (Current speed/current synchronization control. synchroni- When the master axis is the semi-closed control. zation) The setting of the slave axis in the D E (Current speed/current synchronization control. synchroni- When the master axis is the full-closed control. (Current synchronization control is only for zation) MDS-C2-Vx.) E Setting impossible

8 9

Setting impossible

II - 147

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2226 SV026 OD2

Items Excessive error detection width during servo OFF Servo function selection 1

Details

Setting range

2227

SV027 SSF1

Set the excessive error detection width when servo ON. 0 to 32767 For the standard setting, refer to the explanation of (mm) SV023 (OD1). When 0 is set, the excessive error detection will not be performed. F E D C B A 9 8 aflt zrn2 afse ovs lmc 7 6 5 4 3 2 1 0 omr zrn3 vfct upc vcnt Meaning when 0 is set Meaning when 1 is set Set the execution changeover type of the speed loop delay 0 vcnt compensation. 1 00: Delay compensation changeover invalid 01: Delay compensation changeover type 1 10: Delay compensation type 2 11: Setting prohibited Start torque compensation Start torque compensation 2 upc invalid valid 3 Set the number of compensation pulses of the jitter 4 vfct compensation. 00: Jitter compensation invalid 5 01: Jitter compensation 1 pulse 10: Jitter compensation 2 pulses 11: Jitter compensation 3 pulses 6 zrn3 ABS scale: Set to 1 in using AT342, AT343, LC191M/491M. Machine end compensation Machine end compensation 7 omr invalid valid Set the compensation amount with SV016 (LMC1) and SV041 8 lmc (LMC2). 00: Lost motion compensation stop 9 01: Lost motion compensation type 1 10: Overshooting compensation type 2 11: Setting prohibited Set the compensation amount with SV031 (OVS1) and SV042 A ovs (OVS2). B 00: Overshooting compensation stop 01: Overshooting compensation type 1 10: Overshooting compensation type 2 11: Overshooting compensation type 3 C 00: Adoptive filter sensitivity standard afse 11: Adoptive filter sensitivity increase (Set 2bits at a time) D E zrn2 Set to 1. F aflt Adoptive filter stop Adoptive filter start (Note) Set to 0 for bits with no particular description. bit

2228 SV028 2229 SV029 Speed at the change of speed loop gain

Not used. Set to 0.

If the noise is bothersome at high speed during rapid 0 to 9999 traverse, etc, lower the speed loop gain. (r/min) Set the speed at which the speed loop gain changes, and use this with SV006 (VGN2). (Refer to SV006.) When not using, set to 0.

II - 148

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No.

Items

Details

Setting range 0 to 32767 0 to 255 (%)

2230 The higher order 8bits and lower order 8bits are used for different functions. The setting value of SV030 = (Icx*256) + IVC SV030 IVC (Low order) Voltage dead time compensation When 100% is set, the voltage equivalent to the logical non-energized time will be compensated. When 0 is set, a 100% compensation will be performed. Adjust in increments of 10% from the default value 100%. If increased too much, vibration or vibration noise may be generated. Set to 0 as a standard. Use this in combination with SV040 and the high order 8bits of SV045. Set this if overshooting occurs during positioning. This compensates the motor torque during positioning. This is valid only when the overshooting compensation SV027 (SSF1/ovs) is selected. Type 1: When SV027 (SSF1)/ bitB, A (ovs)=01 Set the compensation amount based on the motors stall current. This compensates overshooting that occurs during pulse feeding. Normally, use Type 2. Type 2: When SV027 (SSF1)/ bitB, A (ovs)=10 Set the compensation amount based on the motors stall current. Increase by 1% and determine the amount that overshooting doesnt occur. In Type 2, compensation during the feed forward control during circular cutting wont be performed. Type 3: When SV027 (SSF1)/ bitB, A (ovs)=11 Use this to perform the overshooting compensation during circular cutting or the feed forward control. The setting method is the same in Type 2. When you wish different compensation amount depending on the direction When SV042 (OVS2) is 0, compensate with the value of SV031 (OVS1) in both of the + and -directions. If you wish to change the compensation amount depending on the command direction, set this and SV042 (OVS2). (SV031: + direction, SV042: direction. However, the directions may be opposite depending on other settings.) When -1 is set, the compensation wont be performed in the direction of the command. 2232 SV032 TOF Torque offset

SV030 Icx (High order) 2231 SV031 OVS1

Current bias 1

0 to 127

Overshooting compensation 1

-1 to 100 (Stall [rated] current %)

Set the unbalance torque of vertical axis and inclined -100 to 100 axis. (Stall [rated] current %)

II - 149

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2233 SV033 SSF2

Items Servo function selection 2 F 7 E dos 6 nfd2

Details D C 5 4 nf3

B 3

A 2 nfd1

Setting range 9 8 hvx svx 1 0 zck

bit Meaning when 0 is set Meaning when 1 is set 0 zck Z phase check valid (Alarm 42) Z phase check invalid 1 Set the filter depth for Notch filter 1 (SV038). 2 Value 000 001 010 011 100 101 110 111 nfd1 Depth Infntly 3 -18.1 -12.0 -8.5 -6.0 -4.1 -2.5 -1.2 (dB) deep Deep Shallow 4 nf3 Notch filter 3 stop Notch filter 3 start (1125Hz) 5 Set the operation frequency of Notch filter 2 (SV046). 6 Value 000 001 010 011 100 101 110 111 nfd2 Depth Infntly 7 -18.1 -12.0 -8.5 -6.0 -4.1 -2.5 -1.2 (dB) deep Deep Shallow Set the performance mode of the servo control. 8 svx (Only for MDS-C1-Vx) 9 hvx 00: By current loop gain 01: MDS-B-Vx compatible mode selected 10: High gain mode selected 11: High gain mode selected A B C Digital signal output selection 0 : MP scale absolute position detection, offset demand D signal output dos E 1 : Specified speed signal output F 2 to F : Setting prohibited (Note) Set to 0 for bits with no particular description.

II - 150

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2234 SV034 SSF3

Items Servo function selection 3 F 7 E ovsn 6 os2

Details D C 5 zeg 4

B 3

A 2 mohn

Setting range 9 8 1 has2 0 has1

Meaning when 0 is set Setting for normal use 0 has1 (Except for HC) 1 has2 Setting for normal use (Except for HC)

bit

Meaning when 1 is set HAS control 1 valid (HC: High acceleration rate support) HAS control 2 valid (HC: Overshooting support)

moh MDS-B-HR motor thermal MDS-B-HR motor thermal ignored n valid

3 4 5 zeg Z phase normal edge detection (Setting for normal use) Setting for normal use 6 os2

Z phase reverse edge detection (Valid only when SV027/bit6=1) Overspeed detection level changeover

7 8 9 A B Set the non-sensitive band of the overshooting compensation type C 3 in increments of 2m at a time. D ovsn In the feed forward control, the non-sensitive band of the model E position droop is set, and overshooting of the model is ignored. F Set the same value as the standard SV040. (Note) Set to 0 for bits with no particular description.

II - 151

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2235 SV035 SSF4

Items Servo function selection 4 F clt 7 ckab bit 0 1 2 tdt 3 4 5 6 iup 7 ckab cltq 9 A clet 8 E 6 iup

Details D C clG1 5 4

B cl2n 3 tdt

A clet 2

Setting range 9 8 cltq 1 0

Meaning when 0 is set Meaning when 1 is set Td creation time setting Set to 0. (For machine tool builder adjustment)

B cl2n C D clG1 E F clt

Set to 1 when using any of motors from HC152 to HC702 and from HC153 to HC453. Setting for normal use No signal 2 (Alarm 21) special detection Set the retracting torque for collision detection in respect to the maximum torque of the motor. 00: 100% 01: 90% 10: 80% (Standard) 11: 70% Setting for normal use The disturbance torque peak of the latest two seconds is displayed in MPOS of the servo monitor screen. Collision detection method 2 Collision detection method 2 valid invalid Collision detection method 1 Set the collision detection level during cutting feed (G1). The G1 collision detection level=SV060*clG1. When clG1=0, the collision detection method 1 during cutting feed wont function. Setting for normal use The guide value of the SV059 setting value is displayed in MPOS of the servo monitor screen.

(Note) bit7 (ckab) is only for MDS-C1-Vx.

II - 152

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2236 SV036 (PR) PTYP

Items Power supply type F 7 E amp 6

Details D C 5 4 ptyp

B 3

A rtyp 2

Setting range 9 8 1 0

Explanation When the CN4 connector of the drive unit and the power supply are connected, setting below is necessary. To validate the external emergency stop function, add 40h. Set3 0x 1x 2x 3x 4x 5x 6x 7x 8x ting ptyp Not 4 x0 CV-300 used 5 x1 CV-110 CR-10 6 x2 CV-220 CR-15 7 x3 CR-22 x4 CV-37 CR-37 x5 CV-150 CV-450CV-550 x6 CV-55 CV-260 CR-55 x7 CV-370 x8 CV-75 CR-75 x9 CV-185 CR-90 0 1 2 Set the regenerative resistor type when MDS-A-CR is used. SetRegenerative resistor Resistance 9 Capacity ting model name value rtyp MDS-C1-CV (Setting when using power supply A 0 regeneration) B 1 GZG200W260HMJ 80W 26 2 150W GZG300W130HMJ2 26 3 MR-RB30 300W 13 4 MR-RB50 500W 13 5 350W GZG200W200HMJ3 6.7 6 500W GZG300W200HMJ3 6.7 7 R-UNIT-1 700W 30 8 R-UNIT-2 700W 15 9 R-UNIT-3 2100W 15 A to F No setting Always set to 0. C D amp E F 2237 SV037 JL Load inertia scale Set the motor inertia + motor axis conversion load inertia in respect to the motor inertia. SV037 (JL) = Jl+Jm Jm *100 0 to 5000 (%) 8

bit

Jm: Motor inertia Jl: Motor axis conversion load inertia 2238 SV038 FHz1 Notch filter frequency 1 Set the vibration frequency to suppress if machine vibration occurs. (Valid at 36 or more) When not using, set to 0. 0 to 9000 (Hz)

II - 153

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2239 SV039 LMCD

Items Lost motion compensation timing

Details Set this when the lost motion compensation timing doest not match. Adjust by increasing the value by 10 at a time.

Setting range 0 to 2000 (ms) 0 to 32767 0 to 100 (m)

2240 The higher order 8bits and lower order 8bits are used for different functions. Setting value of SV040 = (Icy*256) + LMCT SV040 LMCT (Low order) SV040 Icy (High order) 2241 SV041 LMC2 Lost motion compensation non-sensitive band Current bias 2 Set the non-sensitive band of the lost motion compensation in the feed forward control. When 0 is set, the actual value that is set is 2m. Adjust by increasing by 1m at a time. Normally, set to 40 if you use HC202 to HC902, HC203 to HC703. Use this in combination with SV030 and the high order 8bits of SV045. Set this with SV016 (LMC1) only when you wish to set the lost motion compensation amount to be different depending on the command directions. Set to 0 as a standard. Set this with SV031 (OVS1) only when you wish to set the overshooting compensation amount to be different depending on the command directions. Set to 0 as a standard.

0 to 127

Lost motion compensation 2 Overshooting compensation 2 Disturbance observer filter frequency Disturbance observer gain

-1 to 200 (Stall [rated] current %) -1 to 100 (Stall [rated] current %)

2242 SV042 OVS2

2243 SV043 OBS1

Set the disturbance observer filter band. 0 to 1000 Set to 100 as a standard. (rad/s) To use the disturbance observer, also set SV037 (JL) and SV044 (OBS2). When not using, set to 0. Set the disturbance observer gain. The standard 0 to 500 setting is 100 to 300. (%) To use the disturbance observer, also set SV037 (JL) and SV043 (OBS1). When not using, set to 0. 0 to 32767 0 to 100 (Stall [rated] current %) 0 to 127

2244 SV044 OBS2

2245 The higher order 8bits and lower order 8bits are used for different functions. Setting value of SV045 = (Icy*256) + LMCT SV045 TRUB (Low order) SV045 Ib1 (High order) 2246 SV046 FHz2 2247 SV047 EC Frictional torque When you use the collision detection function, set the frictional torque.

Current bias 3

Set to 0 as a standard. Use this in combination with SV030 and the high order 8bits of SV040. Set the vibration frequency to suppress if machine vibration occurs. (Valid at 36 or more) When not using, set to 0.

Notch filter frequency 2 Inductive voltage compensation gain

0 to 9000 (Hz)

Set the inductive voltage compensation gain. Set to 0 to 200 100 as a standard. (%) If the current FB peak exceeds the current command peak, lower the gain.

2248 SV048 EMGrt

Vertical axis Input a length of time to prevent the vertical axis from 0 to 20000 drop prevention dropping by delaying Ready OFF until the brake (ms) time works when the emergency stop occurs. Increase the setting by 100ms at a time and set the value where the axis does not drop.

II - 154

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2249 SV049 PGN1sp

Items Position loop gain 1 in spindle synchronous control

Details Set the position loop gain during the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). Set the same value as the value of the spindle parameter, position loop gain in synchronous control. When performing the SHG control, set this with SV050 (PGN2sp) and SV058 (SHGCsp).

Setting range 1 to 200 (rad/s)

2250 PGN2sp

Position loop gain 2 in spindle synchronous control

Set this with SV049 (PGN1sp) and SV058 0 to 999 (SHGCsp) if you wish to perform the SHG control in (rad/s) the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). When not performing the SHG control, set to 0. 0 to 9999 (ms)

2251 SV051 DFBT

Dual feed back Set the control time constant in dual feed back. control time When 0 is set, the actual value that is set is 1ms. constant The higher the time constant is, the closer it gets to the semi-closed control, so the limit of the position loop gain is raised. Dual feedback control non-sensitive band Excessive error detection width in special control Set the non-sensitive band in the dual feedback control. Set to 0 as a standard. Set the excessive error detection width when servo ON in a special control (initial absolute position setting, stopper control, etc.). If 0 is set, excessive error detection wont be performed when servo ON during a special control.

2252 SV052 DFBN

0 to 9999 (m)

2253 SV053 OD3

0 to 32767 (mm)

II - 155

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. SV054 ORE

Items Overrun detection width in closed loop control

Details Set the overrun detection width in the full-closed loop control. If the gap between the motor end detector and the linear scale (machine end detector) exceeds the value set by this parameter, it is judged to be overrun and Alarm 43 will be detected. When -1 is set, the alarm detection wont be performed. When 0 is set, overrun is detected with a 2mm width.

Setting range -1 to 32767 (mm)

2254 When SV035 (SSF4)/ bitF (ckab)=0

When SV035 (SSF4)/ bitF (ckab)=1 (Note) This applies to only MDS-C1-Vx. The higher order 8bits and lower order 8bits are used for different functions. Setting value of SV054 =(NSE*256)+ORE SV054 ORE (Low order) Overrun detectionwidth in closed loop control

0 to 32767

Set the overrun detection width in the full-closed loop 0 to 255 control. (mm) If the gap between the motor end detector and the linear scale (machine end detector) exceeds the value set by this parameter, it is judged to be overrun and Alarm 43 will be detected. When 255 is set, the alarm detection wont be performed. When 0 is set, overrun is detected with a 2mm width.

SV054 NSE (High order) 2255 SV055 EMGx

Special When SV035 (SSF4)/ bitF (ckab) =1, this setting is 0 to 127 detection width valid. Set the special detection width for No signal 2 (m) for No signal 2 (Alarm 21). When 0 is set, overrun is detected with a 15m width. Max. gate off delay time after emergency stop Set a length of time from the point when the 0 to 20000 emergency stop is input to the point when READY (ms) OFF is compulsorily executed. Normally, set the same value as the absolute value of SV056. In preventing the vertical axis from dropping, the gate off is delayed for the length of time set by SV048 if SV055s value is smaller than that of SV048. In the vertical axis drop prevention time control, set -20000 to 20000 the time constant used for the deceleration control at (ms) emergency stop. Set a length of time that takes from rapid traverse rate (rapid) to stopping. Normally, set the same value as the rapid traverse acceleration/deceleration time constant. When executing the synchronous operation, put the minus sign to the settings of both of the master axis and slave axis. When performing the SHG control, set this with S003 0 to 1200 (PGN1) and SV004 (PGN2). (rad/s) When not performing the SHG control, set to 0. Set this with SV049 (PGN1sp) and SV050 (PGN2sp) 0 to 1200 if you wish to perform the SHG control in the spindle (rad/s) synchronous control (synchronous tapping, synchronous control with spindle/C axis). When not performing the SHG control, set to 0.

2256 SV056 EMGt

Deceleration time constant at emergency stop

2257 SV057 SHGC 2258 SV058 SHGCsp

SHG control gain SHG control gain in spindle synchronous control

II - 156

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

No. 2259 SV059 TCNV

Items Collision detection torque estimating gain

Details

Setting range

Set the torque estimating gain when using the -32768 to 32767 collision detection function. After setting as SV035/bitF(clt)=1 and performing acceleration/deceleration, set the value displayed in MPOS of the NC servo monitor screen. Set to 0 when not using the collision detection function. When using the collision detection function, set the collision detection level during the G0 feeding. If 0 is set, none of the collision detection function will work. 0 to 999 (Stall [rated] current %)

2260 SV060 TLMT

Collision detection level

2261 SV061 DA1NO 2262 SV062 DA2NO 2263 SV063 DA1MPY 2264 SV064 DA2MPY 2265 SV065 TLC

D/A output Input the data number you wish to output to D/A -1 to 127 channel 1 data output channel. No. In the case of MDS-C1-V2, set the axis on the side to which the data will not be output to -1. D/A output channel 2 data No. D/A output channel 1 output scale D/A output channel 2 output scale Tool end Set the spring constant of the tool end compensation compensation. spring constant In the semi-closed loop control, the tool end compensation amount is calculated with the following equation. Compensation amount= F (mm/min)2*SV065 R (mm)*109 (m) -32768 to 32767 Set the scale with a 1/256 unit. When 0 is set, output is done with the standard output unit. -32768 to 32767 (Unit: 1/256)

F: Commanded speed R: Radius When not using, set to 0.

II - 157

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

(2) Initial setting value (a) HC**/HC**R series HC 52 05 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxB0 6 4000 0 0 0 0 0 HC 102 10 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxB1 6 4000 0 0 0 0 0 HC 152 20 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxB2 6 4000 0 0 0 0 0 HC 202 20 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxB3 6 4000 0 0 0 0 0 HC 352 35 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxB4 6 4000 0 0 0 0 0 45s 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 1000 60 150 6 50 xx95 6 4000 0 0 0 0 0 HC 452 45 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxB5 6 4000 0 0 0 0 0 70s 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 1000 60 150 6 50 xx96 6 4000 0 0 0 0 0 HC 702 70 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxB6 6 4000 0 0 0 0 0 HC 902 90 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxB7 6 4000 0 0 0 0 0

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 VGN2 SV007 VIL SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 VCS SV030 IVC SV031 OVS1 SV032 TOF

II - 158

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 FHz2 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 DFBT SV052 DFBN SV053 OD3 SV054 ORE SV055 EMGx SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065 TLC

HC 52 05 0000 0003 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 102 10 0000 0003 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 152 20 0000 0003 0040 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 202 20 0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 352 35 0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 45s

HC 452 45 0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 70s

HC 702 70 0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 902 90 0000 0003 0000 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 159

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 VGN2 SV007 VIL SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 VCS SV030 IVC SV031 OVS1 SV032 TOF

HC 53 05 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxC0 6 4000 0 0 0 0 0

HC 103 10 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxC1 6 4000 0 0 0 0 0

HC 153 20 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxC2 6 4000 0 0 0 0 0

HC 203 35 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxC3 6 4000 0 0 0 0 0 45s

HC 353 45 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxC4 6 4000 0 0 0 0 0 70s

HC 453 70 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxC5 6 4000 0 0 0 0 0

HC 703 90 47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xxC6 6 4000 0 0 0 0 0

47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 1000 60 150 6 50 xxA4 6 4000 0 0 0 0 0

47 0 200 0 0 1364 4096 4096 768 768 500 500 0 0 1000 60 150 6 50 xxA5 6 4000 0 0 0 0 0

II - 160

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 FHz2 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 DFBT SV052 DFBN SV053 OD3 SV054 ORE SV055 EMGx SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065 TLC

HC 53 05 0000 0003 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 103 10 0000 0003 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 153 20 0000 0003 0040 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 203 35 0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 45s

HC 353 45 0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 70s

HC 453 70 0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 703 90 0000 0003 0000 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 161

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 VGN2 SV007 VIL SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 VCS SV030 IVC SV031 OVS1 SV032 TOF

HC 103R 10 33 0 15 0 0 1364 4096 4096 256 512 500 500 0 0 0000 60 150 6 50 xxE1 6 4000 0 0 0 0 0

HC 153R 10 33 0 15 0 0 1364 4096 4096 256 512 500 500 0 0 0000 60 150 6 50 xxE2 6 4000 0 0 0 0 0

HC 203R 20 33 0 20 0 0 1364 4096 4096 256 512 500 500 0 0 0000 60 150 6 50 xxE3 6 4000 0 0 0 0 0

HC 353R 35 33 0 40 0 0 1364 4096 4096 256 512 500 500 0 0 0000 60 150 6 50 xxE4 6 4000 0 0 0 0 0

II - 162

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 FHz2 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 DFBT SV052 DFBN SV053 OD3 SV054 ORE SV055 EMGx SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065 TLC

HC 103R 10 0200 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 153R 10 0200 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 203R 20 0200 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 353R 35 0200 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 163

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

(b) HA**N series HA 40N 05 33 0 150 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx00 6 4000 0 0 0 0 0 HA 80N 10 33 0 150 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx01 6 4000 0 0 0 0 0 HA 100N 20 33 0 150 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx02 6 4000 0 0 0 0 0 HA 200N 35 33 0 150 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx03 6 4000 0 0 0 0 0 HA 300N 45 33 0 150 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx04 6 4000 0 0 0 0 0 HA 700N 70 25 0 250 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx05 6 4000 0 0 0 0 0 HA 900N 90 25 0 250 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx06 6 4000 0 0 0 0 0

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 VGN2 SV007 VIL SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 VCS SV030 IVC SV031 OVS1 SV032 TOF

II - 164

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 FHz2 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 DFBT SV052 DFBN SV053 OD3 SV054 ORE SV055 EMGx SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065 TLC

HA 40N 05 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 80N 10 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 100N 20 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 200N 35 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 300N 45 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 700N 70 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 900N 90 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 165

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 SV007 SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 SV030 IVC SV031 OVS1 SV032 TOF

HA 43N 05 33 0 150 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx80 6 4000 0 0 0 0 0

HA 83N 10 33 0 150 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx81 6 4000 0 0 0 0 0

HA 93N 20 33 0 150 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx8A 6 4000 0 0 0 0 0

HA 103N 35 33 0 150 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx82 6 4000 0 0 0 0 0

HA 203N 45 33 0 150 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx83 6 4000 0 0 0 0 0

HA 303N 70 33 0 150 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx84 6 4000 0 0 0 0 0

HA 703N 90 25 0 250 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx85 6 4000 0 0 0 0 0

HA 053N 01 33 0 70 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx8C 6 4000 0 0 0 0 0

HA 13N 01 33 0 70 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx8D 6 4000 0 0 0 0 0

HA 23N 03 33 0 100 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx8E 6 4000 0 0 0 0 0

HA 33N 03 33 0 100 0 0 1364 4096 4096 768 768 500 500 0 0 0000 60 150 6 50 xx8F 6 4000 0 0 0 0 0

II - 166

7.2

7. SERVO PARAMETERS MDS-C1-Vx HIGH-GAIN (MDS-B-Vx4 COMPATIBLE)

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 FHz2 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 DFBT SV052 DFBN SV053 OD3 SV054 ORE SV055 EMGx SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065 TLC

HA 43N 05 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 83N 10 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 93N 20 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 103N 35 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 203N 45 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 303N 70 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 703N 90 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 053N 01 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 13N 01 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 23N 03 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 33N 03 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 167

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

7.3 MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

(1) Details for servo parameters For parameters marked with a (PR) in the table, turn the NC power OFF after setting. After the power is turned ON again, the parameter is validated.

! CAUTION
!

In the explanation on bits, set all bits not used, including blank bits, to 0. Items Details Setting range

No. 2201 SV001 (PR) PC1 2202 SV002 (PR) PC2 2203 SV003 PGN1

Motor side gear Set the motor side and machine side gear ratio. 1 to 32767 ratio For the rotary axis, set the total deceleration (acceleration) ratio. Machine side 1 to 32767 Even if the gear ratio is within the setting range, the gear ratio electronic gears may overflow and cause an alarm. Position loop gain 1 Set the position loop gain. The standard setting is 33. The higher the setting value is, the more precisely the command can be followed and the shorter the positioning time gets, however, note that a bigger shock is applied to the machine during acceleration/deceleration. When using the SHG control, also set SV004 (PGN2) and SV057 (SHGC). When using the SHG control, also set SV003 (PGN1) and SV057 (SHGC). When not using the SHG control, set to 0. 1 to 200 (rad/s)

2204 SV004 PGN2 2205 SV005 VGN1

Position loop gain 2

0 to 999 (rad/s)

Speed loop gain Set the speed loop gain. 1 to 999 1 Set this according to the load inertia size. The higher the setting value is, the more accurate the control will be, however, vibration tends to occur. If vibration occurs, adjust by lowering by 20 to 30%. The value should be determined to be 70 to 80% of the value at the time when the vibration stops. Speed loop gain If the noise is bothersome at high speed during rapid -1000 to 1000 2 traverse, etc, lower the speed loop gain. As in the right figure, set the speed loop gain of the speed 1.2 times as fast as the motors rated speed, and use this with SV029 (VCS). When not using, set to 0.

2206 SV006 VGN2

VGN1 VGN2 0 VCS VLMT (Rated speed*1.2)

II - 168

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No. 2207 SV007 VIL

Items Speed loop delay compensation

Details

Setting range

Set this when the limit cycle occurs in the full-closed 0 to 32767 loop, or overshooting occurs in positioning. Select the control method with SV027 (SSF1)/bit1, 0 (vcnt). Normally, use Changeover type 2. When you set this parameter, make sure to set the torque offset (SV032 (TOF)). When not using, set to 0. No changeover When SV027 (SSF1)/ bit1, 0 (vcnt)=00 The delay compensation control is always valid. Changeover type 1 When SV027 (SSF1)/ bit1, 0 (vcnt)=01 The delay compensation control works when the command from the NC is 0. Overshooting that occurs during pulse feeding can be suppressed. Changeover type 2 When SV027 (SSF1)/ bit1, 0 (vcnt)=10 The delay compensation control works when the command from the NC is 0 and the position droop is 0. Overshooting or the limit cycle that occurs during pulse feeding or positioning can be suppressed.

2208 SV008 VIA

Speed loop lead compensation

Set the gain of the speed loop integration control. The standard setting is 1364. During the SHG control, the standard setting is 1900. Adjust the value by increasing/decreasing it by about 100 at a time. Raise this value to improve contour tracking precision in high-speed cutting. Lower this value when the position droop vibrates (10 to 20Hz).

1 to 9999

2209 SV009 IQA 2210 SV010 IDA 2211 SV011 IQG 2212 SV012 IDG 2213 SV013 ILMT

Current loop q axis lead compensation Current loop d axis lead compensation Current loop q axis gain Current loop d axis gain Current limit value

1 to 20480 Set the gain of current loop. As this setting is determined by the motors electrical characteristics, the setting is fixed for each type of motor. 1 to 20480 Set the standard values for all the parameters depending on each motor type. 1 to 2560 1 to 2560 Set the normal current (torque) limit value. (Limit values for both + and - direction.) When the value is 500 (a standard setting), the maximum torque is determined by the specification of the motor. 0 to 999 (Stall [rated] current %)

2214 SV014 ILMTsp

Current limit Set the current (torque) limit value in a special value in special control (initial absolute position setting, stopper control control, etc). (Limit values for both of the + and directions.) Set to 500 when not using.

0 to 999 (Stall [rated] current %)

II - 169

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No. 2215 SV015 FFC

Items Acceleration rate feed forward gain

Details

Setting range

When a relative error in the synchronous control is 0 to 999 large, apply this parameter to the axis that is (%) delaying. The standard setting value is 0. For the SHG control, set to 100. To adjust a relative error in acceleration/deceleration, increase the value by 50 to 100 at a time. Set this when the protrusion (that occurs due to the non-sensitive band by friction, torsion, backlash, etc) at quadrant change is too large. This compensates the torque at quadrant change. This is valid only when the lost motion compensation (SV027 (SSF1/lmc)) is selected. Type 1: When SV027 (SSF1)/ bit9, 8 (lmc)=01 Set the compensation amount based on the motor torque before the quadrant change. The standard setting is 100. Setting to 0 means the compensation amount is zero. Normally, use Type 2. -1 to 200 (%)

2216 SV016 LMC1

Lost motion compensation 1

Type 2: When SV027 (SSF1)/ bit9, 8 (lmc)=10 -1 to 100 Set the compensation amount based on the stall (Stall [rated] (rated) current of the motor. current %) The standard setting is double of the friction torque. Setting to 0 means the compensation amount is zero. When you wish different compensation amount depending on the direction When SV041 (LMC2) is 0, compensate with the value of SV016 (LMC1) in both of the + and -directions. If you wish to change the compensation amount depending on the command direction, set this and SV041 (LMC2). (SV016: + direction, SV041: direction. However, the directions may be opposite depending on other settings.) When -1 is set, the compensation wont be performed in the direction of the command.

II - 170

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No. 2217 (PR) SV017 SPEC

Items Servo specification selection F 7 abs bit 0 1 E 6

Details D C 5 vdir 4 fdir

B 3 spwv

A 2 seqh

Setting range 9 8 mpt3 mp 1 dfbx 0 fdir2

Meaning when 0 is set Speed feedback forward fdir2 polarity dfbx Dual feedback control stop

2 seqh 3 spwv 4 5 6 7 8 fdir vdir

Meaning when 1 is set Speed feedback reverse polarity Dual feedback control start READY/Servo ON time high READY/Servo ON time normal speed High gain servo synchronous Normal mode mode Position feedback forward Position feedback reverse polarity polarity HA motor (4 pole motor) Detector installation position Standard setting 90 degrees (B, D) Absolute position control MP scale 720P (1mm pitch) MP scale ABS detection type 3

abs Incremental control mp MP scale 360P (2mm pitch) MP scale ABS detection type 9 mpt3 1, 2 A B C D E F 2218 (PR) SV018 PIT Ball screw pitch

(Note) Set to 0 for bits with no particular description. Set the ball screw pitch. Set to 360 for the rotary axis. 1 to 32767 (mm/rev)

II - 171

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No. 2219 SV019 (PR) RNG1

Items Position detector resolution

Details In the case of the semi-closed loop control Set the same value as SV020 (RNG2). (Refer to the explanation of SV020.) In the case of the full-closed loop control Set the number of pulses per ball screw pitch. Detector model name OHE25K-ET, OHA25K-ET OSE104-ET, OSA104-ET OSE105-ET, OSA105-ET Relative position detection scale AT41 (Mitsutoyo) FME type, FLE type (Futaba) MP type (Mitsubishi Heavy Industries) AT342 (Mitsutoyo) Resolution 100,000(p/rev) 100,000(p/rev) 1,000,000(p/rev) Refer to specification manual for each detector 1 (m/p) Refer to specification manual for each detector Refer to specification manual for each detector 0.5 (m/p)

Setting range 1 to 9999 (kp/rev) 1 to 9999 (kp/pit) SV019 setting 100 100 1000 PIT/Resolution (m) The same as SV018 (PIT) PIT/Resolution (m) PIT/Resolution (m) Twice as big as SV018 (PIT)

2220 SV020 (PR) RNG2

Speed detector resolution

Set the number of pulses per one revolution of the motor 1 to 9999 end detector. (kp/rev) Detector model name Equipped to HA053, HA13 (Only for MDS-B-Vx) OHE25K, OHA25K (Only for MDS-B-Vx) OSE104, OSA104 OSE105, OSA105 SV020 setting 10 100 100 1000

2221 SV021 OLT 2222 SV022 OLL 2223 SV023 OD1

Overload Set the detection time constant of Overload 1 (Alarm 50). 1 to 999 detection Set to 60 as a standard. (For machine tool builder (s) time constant adjustment.) Overload detection level Excessive error detection width during servo ON Set the current detection level of Overload 1 (Alarm 50) in 110 to 500 respect to the stall (rated) current. Set to 150 as a (Stall [rated] standard. (For machine tool builder adjustment.) current %) Set the excessive error detection width when servo ON. <Standard setting value> Rapid traverse rate (mm/min) OD1=OD2= 60*PGN1 /2 (mm) When 0 is set, the excessive error detection will not be performed. 0 to 32767 (mm)

II - 172

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No. 2224 SV024 INP

Items In-position detection width

Details

Setting range

2225 (PR)

SV025 MTYP

Motor/ Detector type

Set the in-position detection width. 0 to 32767 Set the accuracy required for the machine. (m) The lower the setting is, the higher the positioning accuracy gets, however, the cycle time (setting time) becomes longer. The standard setting is 50. F E D C B A 9 8 pen ent 7 bit 6 5 4 mtyp Explanation Set the motor type. Set1 0x 1x 2x 3x 4x 5x 6x 7x ting 2 x0 HA40N HA50L HA53L 3 mtyp x1 HA80N HA100L HA103L 4 x2 HA100N HA200L HA203L 5 x3 HA200N HA300L HA303L 6 x4 HA300N HA500L HA503L 7 x5 HA700N x6 HA900N x7 HA-LH11K2 x8 HA-LH15K2 x9 xA HA150L HA153L xB xC xD xE xF 0 Set8x 9x Ax Bx Cx Dx Ex Fx ting x0 HA43N HC52 HC53 x1 HA83N HC102 HC103 HC103R x2 HA103N HC152 HC153 HC153R x3 HA203N HC202 HC203 HC203R x4 HA303N HC352 HC353 HC353R x5 HA703N HC452 HC453 HC503R x6 HC702 HC703 x7 HC902 x8 x9 xA HA93N xB xC HA053(N) xD HA13(N) xE HA23N xF HA33N (To be continued to the next page) 3 2 1 0

II - 173

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No.

Items

Details

Setting range

(Continued from the previous page) bit Explanation Set the detector type. Set position detector type for pen, and 8 speed detector type for ent. In the case of the semi-closed 9 ent loop control, set the same value for pen and ent. A B pen setting ent setting C Detector model name OHE25K (Only for D 0 0 MDS-B-Vx), OSE104 pen OHA25K (Only for E 1 1 MDS-B-Vx), OSA104 F 2 3 4 5 6 7 8 9 A B 2 3 Setting impossible Setting impossible Setting impossible Setting impossible Setting impossible Setting impossible Setting impossible Setting impossible C (Current synchronization) Setting impossible Setting impossible Setting impossible The setting of the slave axis in the speed/current synchronization control. When the master axis is the semi-closed control. Relative position detection scale, MP type (Mitsubishi Heavy Industries) AT41 (Mitsutoyo), FME type, FLE type (Futaba) AT342 (Mitsutoyo) OSE105, OSA105 Equipped to HA053, HA13 (Only for MDS-B-Vx) OHE25K-ET, OSE104-ET OHA25K-ET, OSA104-ET OSE105-ET, OSA105-ET

D E F

2226 SV026 OD2

Excessive error detection width during servo OFF

Set the excessive error detection width when servo ON. 0 to 32767 For the standard setting, refer to the explanation of (mm) SV023 (OD1). When 0 is set, the excessive error detection will not be performed.

II - 174

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No. 2227 SV027 SSF1

Items Servo function selection 1 F aflt 7 E zrn2 6 zrn3

Details D C afse 5 vfct 4

B ovs 3

A 2 upc

Setting range 9 8 lmc 1 vcnt 0

bit 0 vcnt 1

2 upc 3 4 5 vfct

Meaning when 0 is set Meaning when 1 is set Set the execution changeover type of the speed loop delay compensation. 00: Delay compensation changeover invalid 01: Delay compensation changeover type 1 10: Delay compensation type 2 11: Setting prohibited Start torque compensation Start torque compensation invalid valid Set the number of compensation pulses of the jitter compensation. 00: Jitter compensation invalid 01: Jitter compensation 1 pulse 10: Jitter compensation 2 pulses 11: Jitter compensation 3 pulses ABS scale: Set to 1 in using AT342, AT343, LC191M/491M. Set the compensation amount with SV016 (LMC1) and SV041 (LMC2). 00: Lost motion compensation stop 01: Lost motion compensation type 1 10: Lost motion compensation type 2 11: Setting prohibited Set the compensation amount with SV031 (OVS1) and SV042 (OVS2). 00: Overshooting compensation stop 01: Overshooting compensation type 1 10: Overshooting compensation type 2 11: Overshooting compensation type 3 00: Adoptive filter sensitivity standard 11: Adoptive filter sensitivity increase (Set 2bits at a time) Set to 1. Adoptive filter stops Adoptive filter starts 0

6 zrn3 7 8 9 lmc

A B

ovs

C afse D E zrn2 F aflt 2228 SV028 2229 SV029 VCS Speed at the change of speed loop gain

(Note) Set to 0 for bits with no particular description. Not used. Set to 0. If the noise is bothersome at high speed during rapid 0 to 9999 traverse, etc, lower the speed loop gain. (r/min) Set the speed at which the speed loop gain changes, and use this with SV006 (VGN2). (Refer to SV006.) When not using, set to 0.

II - 175

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No.

Items

Details

Setting range 0 to 32767

2230 The higher order 8bits and lower order 8bits are used for different functions. The setting value of SV030 = (Icx*256) + IVC

SV030 Voltage dead IVC time (Low compensation order)

When 100% is set, the voltage equivalent to the logical 0 to 255 non-energized time will be compensated. (%) When 0 is set, a 100% compensation will be performed. Adjust in increments of 10% from the default value 100%. If increased too much, vibration or vibration noise may be generated. Set to 0 as a standard. 0 to 127 Use this in combination with SV040 and the high order 8bits of SV045. Set this if overshooting occurs during positioning. This -1 to 100 compensates the motor torque during positioning. (Stall [rated] This is valid only when the overshooting compensation current%) SV027 (SSF1/ovs) is selected. Type 1: When SV027 (SSF1)/ bitB, A (ovs)=01 Set the compensation amount based on the motors stall current. This compensates overshooting that occurs during pulse feeding. Normally, use Type 2. Type 2: When SV027 (SSF1)/ bitB, A (ovs)=10 Set the compensation amount based on the motors stall current. Increase by 1% and determine the amount that overshooting doesnt occur. In Type 2, compensation during the feed forward control during circular cutting wont be performed. Type 3: When SV027 (SSF1)/ bitB, A (ovs)=11 Use this to perform the overshooting compensation during circular cutting or the feed forward control. The setting method is the same in Type 2. When you wish different compensation amount depending on the direction When SV042 (OVS2) is 0, compensate with the value of SV031 (OVS1) in both of the + and -directions. If you wish to change the compensation amount depending on the command direction, set this and SV042 (OVS2). (SV031: + direction, SV042: - direction. However, the directions may be opposite depending on other settings.) When -1 is set, the compensation wont be performed in the direction of the command.

SV030 Current bias 1 Icx (High order) 2231 SV031 Overshooting OVS1 compensation 1

II - 176

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No. 2232 SV032 TOF 2233 SV033 SSF2

Items Torque offset Servo function selection 2

Details Set the unbalance torque of vertical axis and inclined axis. F 7 E 6 D dos 5 fhz2 4 3 2 nfd 1 C B A

Setting range -100 to 100 (Stall [rated] current %) 9 hvx 0 zck 8 svx

bit 0 zck 1 nfd1 2 3

Meaning when 0 is set

Meaning when 1 is set

Z phase check valid (Alarm 42) Z phase check invalid Set the filter depth for Notch filter 1 (SV038). Value Depth (dB) Deep 0: Invalid 1: 2250Hz 2: 1125Hz 000 Infntly deep 001 -18.1 010 -12.0 011 -8.5 100 101 110 111 -1.2

-6.0 -4.1 -2.5

Shallow 3: 750Hz 4: 563Hz 5: 450Hz 6: 375Hz 7: 321Hz 8 to F: 281Hz

4 5 6 7 8 svx 9 hvx fhz2

Set the operation frequency of Notch filter 2.

Set the performance mode of the servo control. (Only for MDS-C1-Vx) 00: By current loop gain 01: MDS-B-Vx compatible mode selected 10: High gain mode selected 11: High gain mode selected

A B C D E F dos Digital signal output selection 0 : MP scale absolute position detection, offset demand signal output 1 : Specified speed signal output 2 to F : Setting prohibited

(Note) Set to 0 for bits with no particular description.

II - 177

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No. 2234 SV034 SSF3

Items Servo function selection 3 F 7 E ovsn 6 os2

Details D C 5 zeg 4

B 3

A 2

Setting range 9 8 1 has2 0 has1

bit Meaning when 0 is set 0 has1 Setting for normal use (Except for HC)

1 has2 Setting for normal use (Except for HC) 2 3 4 Z phase normal edge detection Z phase reverse edge 5 zeg detection (Setting for normal use) (Valid only when SV027/bit6=1) Setting for normal use Overspeed detection level 6 os2 changeover 7 8 9 A B C Set the non-sensitive band of the overshooting compensation type 3 in increments of 2m at a time. D E ovsn In the feed forward control, the non-sensitive band of the model position droop is set, and overshooting of the model is ignored. F Set the same value as the standard SV040. (Note) Set to 0 for bits with no particular description.

Meaning when 1 is set HAS control 1 valid (HC: High acceleration rate support) HAS control 2 valid (HC: Overshooting support)

II - 178

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No. 2235 SV035 SSF4

Items Servo function selection4 F clt 7 E 6 iup

Details D C clG1 5 4

B cl2n 3 tdt

A clet 2

Setting range 9 8 cltq 1 0

bit 0 1 2 3 4 5 6 7

Meaning when 0 is set Meaning when 1 is set Td creation time setting Set to 0. (For machine tool builder adjustment)

tdt

iup

Set to 1 in the case of any motors from HC152 to HC702 and from HC153 to HC453.

Set the retracting torque for collision detection in respect to the cltq maximum torque of the motor. 9 00: 100% 01: 90% 10: 80% (Standard) 11: 70% Setting for normal use A The disturbance torque peak of the clet latest two seconds is displayed in MPOS of the servo monitor screen. 8 Collision detection method 2 Collision detection method 2 invalid valid Collision detection method 1 C Set the collision detection level during cutting feed (G1). D clG1 The G1 collision detection level=SV060*clG1. When clG1=0, the collision detection method 1 during cutting E feed wont function. Setting for normal use The guide value of the SV059 F clt setting value is displayed in MPOS of the servo monitor screen. (Note) Set to 0 for bits with no particular description. B cl2n

II - 179

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No. 2236 SV036 (PR) PTYP

Items Power supply type F 7 E amp 6

Details D C 5 4 ptyp

B 3

A rtyp 2

Setting range 9 8 1 0

Explanation When the CN4 connector of the drive unit and the power supply are connected, setting below is necessary. To validate the external emergency stop function, add 40h. Set3 0x 1x 2x 3x 4x 5x 6x 7x 8x ting ptyp Not CV-300 4 x0 used 5 x1 CV-110 CR-10 6 x2 CV-220 CR-15 7 x3 CR-22 x4 CV-37 CR-37 x5 CV-150 CV-450 CV-550 x6 CV-55 CV-260 CR-55 x7 CV-370 x8 CV-75 CR-75 x9 CV-185 CR-90 0 1 2 Set the regenerative resistor type when MDS-A-CR is used. SetRegenerative resistor Resistance 9 Capacity ting model name value rtyp MDS-C1-CV (Setting when using power supply A 0 regeneration) B 1 GZG200W260HMJ 80W 26 2 150W GZG300W130HMJ2 26 3 MR-RB30 300W 13 4 MR-RB50 500W 13 5 350W GZG200W200HMJ3 6.7 6 500W GZG300W200HMJ3 6.7 7 R-UNIT-1 700W 30 8 R-UNIT-2 700W 15 9 R-UNIT-3 2100W 15 A to No setting F Always set to 0. C D amp E F 8

bit

II - 180

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No.

Items

Details Set the motor inertia + motor axis conversion load inertia in respect to the motor inertia. SV037 (JL) = Jl+Jm Jm *100

Setting range 0 to 5000 (%)

2237 SV037 JL Load inertia scale

Jm: Motor inertia Jl: Motor axis conversion load inertia 2238 SV038 FHz1 2239 SV039 LMCD Notch filter frequency 1 Lost motion compensation timing Set the vibration frequency to suppress if machine vibration occurs. (Valid at 72 or more) When not using, set to 0. Set this when the lost motion compensation timing doest not match. Adjust by increasing the value by 10 at a time. 0 to 3000 (Hz) 0 to 2000 (ms) 0 to 32767 0 to 100 (m)

2240 The higher order 8bits and lower order 8bits are used for different functions. Setting value of SV040 = (Icy*256) + LMCT SV040 LMCT (Low order) (High order) 2241 SV041 LMC2 Lost motion compensation 2 Overshooting compensation 2 Disturbance observer filter frequency Disturbance observer gain Lost motion compensation non-sensitive band Set the non-sensitive band of the lost motion compensation in the feed forward control. When 0 is set, the actual value that is set is 2m. Adjust by increasing by 1m at a time. Normally, set to 40 if you use HC202 to HC902, HC203 to HC703. Use this in combination with SV030 and the high order 8bits of SV045. Set this with SV016 (LMC1) only when you wish to set the lost motion compensation amount to be different depending on the command directions. Set to 0 as a standard. Set this with SV031 (OVS1) only when you wish to set the overshooting compensation amount to be different depending on the command directions. Set to 0 as a standard.

SV040 Icy Current bias 2

0 to 127

-1 to 200 (Stall [rated] current %) -1 to 100 (Stall [rated] current %)

2242 SV042 OVS2

2243 SV043 OBS1

Set the disturbance observer filter band. 0 to 1000 Set to 100 as a standard. (rad/s) To use the disturbance observer, also set SV037 (JL) and SV044 (OBS2). When not using, set to 0. Set the disturbance observer gain. The standard 0 to 500 setting is 100 to 300. (%) To use the disturbance observer, also set SV037 (JL) and SV043 (OBS1). When not using, set to 0. 0 to 32767 0 to 100 (Stall [rated] current %) 0 to 127

2244 SV044 OBS2

2245 The higher order 8bits and lower order 8bits are used for different functions. Setting value of SV045 = (Icy*256) + LMCT SV045 TRUB (Low order) SV045 Ib1 (High order) Frictional torque When you use the collision detection function, set the frictional torque.

Current bias 3

Set to 0 as a standard. Use this in combination with SV030 and the high order 8bits of SV040.

II - 181

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No. 2246 SV046 2247 SV047 EC

Items Not used. Set to 0. Inductive voltage compensation gain

Details 0

Setting range

Set the inductive voltage compensation gain. Set to 0 to 200 100 as a standard. (%) If the current FB peak exceeds the current command peak, lower the gain.

2248 SV048 EMGrt

Vertical axis Input a length of time to prevent the vertical axis from 0 to 20000 drop prevention dropping by delaying Ready OFF until the brake (ms) time works when the emergency stop occurs. Increase the setting by 100ms at a time and set the value where the axis does not drop. Position loop gain 1 in spindle synchronous control Set the position loop gain during the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). Set the same value as the value of the spindle parameter, position loop gain in synchronous control. When performing the SHG control, set this with SV050 (PGN2sp) and SV058 (SHGCsp). 1 to 200 (rad/s)

2249 SV049 PGN1sp

2250 PGN2sp

Position loop gain 2 in spindle synchronous control

Set this with SV049 (PGN1sp) and SV058 0 to 999 (SHGCsp) if you wish to perform the SHG control in (rad/s) the spindle synchronous control (synchronous tapping, synchronous control with spindle/C axis). When not performing the SHG control, set to 0. 0 to 9999 (ms)

2251 SV051 DFBT

Dual feed back Set the control time constant in dual feed back. control time When 0 is set, the actual value that is set is 1ms. constant The higher the time constant is, the closer it gets to the semi-closed control, so the limit of the position loop gain is raised. Dual feedback control non-sensitive band Excessive error detection width in special control Overrun detection width in closed loop control Set the non-sensitive band in the dual feedback control. Set to 0 as a standard. Set the excessive error detection width when servo ON in a special control (initial absolute position setting, stopper control, etc.). If 0 is set, excessive error detection wont be performed when servo ON during a special control.

2252 SV052 DFBN

0 to 9999 (m)

2253 SV053 OD3

0 to 32767 (mm)

2254 SV054 ORE

Set the overrun detection width in the full-closed loop -1 to 32767 control. (mm) If the gap between the motor end detector and the linear scale (machine end detector) exceeds the value set by this parameter, it is judged to be overrun and Alarm 43 will be detected. When -1 is set, the alarm detection wont be performed. When 0 is set, overrun is detected with a 2mm width. Set a length of time from the point when the 0 to 20000 emergency stop is input to the point when READY (ms) OFF is compulsorily executed. Normally, set the same value as the absolute value of SV056. In preventing the vertical axis from dropping, the gate off is delayed for the length of time set by SV048 if SV055s value is smaller than that of SV048.

2255 SV055 EMGx

Max. gate off delay time after emergency stop

II - 182

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

No. 2256 SV056 EMGt

Items Deceleration time constant at emergency stop

Details

Setting range

In the vertical axis drop prevention control, set the -20000 to 20000 time constant used for the deceleration control at (ms) emergency stop. Set a length of time that takes from rapid traverse rate (rapid) to stopping. Normally, set the same value as the rapid traverse acceleration/deceleration time constant. When executing the synchronous operation, put the minus sign to the settings of both of the master axis and slave axis. When performing the SHG control, set this with S003 0 to 999 (PGN1) and SV004 (PGN2). (rad/s) When not performing the SHG control, set to 0. Set this with SV049 (PGN1sp) and SV050 (PGN2sp) 0 to 999 if you wish to perform the SHG control in the spindle (rad/s) synchronous control (synchronous tapping, synchronous control with spindle/C axis). When not performing the SHG control, set to 0. Set the torque estimating gain when using the -32768 to 32767 collision detection function. After setting as SV035/bitF(clt)=1 and performing acceleration/deceleration, set the value displayed in MPOS of the NC servo monitor screen. Set to 0 when not using the collision detection function. 0 to 999 (Stall [rated] current %)

2257 SV057 SHGC 2258 SV058 SHGCsp

SHG control gain SHG control gain in spindle synchronous control Collision detection torque estimating gain

2259 SV059 TCNV

2260 SV060 TLMT

Collision When using the collision detection function, set the detection level collision detection level during the G0 feeding. If 0 is set, none of the collision detection function will work. D/A output channel 1 data No. D/A output channel 2 data No. D/A output channel 1 output scale D/A output channel 2 output scale Not used. Set to 0.

2261 SV061 DA1NO 2262 SV062 DA2NO 2263 SV063 DA1MPY 2264 SV064 DA2MPY 2265 SV065

Input the data number you wish to output to D/A -1 to 127 output channel. In the case of MDS-C1-V2, set the axis on the side to which the data will not be output to -1.

Set the scale with a 1/256 unit. When 0 is set, output is done with the standard output unit.

-32768 to 32767 (Unit: 1/256)

II - 183

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

(2) Initial setting value (a) HC**/HC**R series HC 52 05 33 0 100 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xxB0 6 4000 0 0 0 0 0 HC 102 10 33 0 100 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xxB1 6 4000 0 0 0 0 0 HC 152 20 33 0 100 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xxB2 6 4000 0 0 0 0 0 HC 202 20 33 0 100 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xxB3 6 4000 0 0 0 0 0 HC 352 35 33 0 100 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xxB4 6 4000 0 0 0 0 0 HC 452 45 33 0 100 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xxB5 6 4000 0 0 0 0 0 HC 702 70 33 0 150 0 0 1364 2048 2048 200 256 500 500 0 0 0000 60 150 6 50 xxB6 6 4000 0 0 0 0 0 HC 902 90 33 0 150 0 0 1364 2048 2048 200 256 500 500 0 0 0000 60 150 6 50 xxB7 6 4000 0 0 0 0 0

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 VGN2 SV007 VIL SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 VCS SV030 IVC SV031 OVS1 SV032 TOF

II - 184

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 DFBT SV052 DFBN SV053 OD3 SV054 ORE SV055 EMGx SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065

HC 52 05 0000 0003 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 102 10 0000 0003 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 152 20 0000 0003 0040 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 202 20 0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 352 35 0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 452 45 0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 702 70 0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 902 90 0000 0003 0040 0000 0 0 0 10240 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 185

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 VGN2 SV007 VIL SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 VCS SV030 IVC SV031 OVS1 SV032 TOF

HC 53 05 33 0 100 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xxC0 6 4000 0 0 0 0 0

HC 103 10 33 0 100 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xxC1 6 4000 0 0 0 0 0

HC 153 20 33 0 100 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xxC2 6 4000 0 0 0 0 0

HC 203 35 33 0 100 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xxC3 6 4000 0 0 0 0 0

HC 353 45 33 0 100 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xxC4 6 4000 0 0 0 0 0

HC 453 70 33 0 100 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xxC5 6 4000 0 0 0 0 0

HC 703 90 33 0 100 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xxC6 6 4000 0 0 0 0 0

HC 103R 10 33 0 15 0 0 1364 4096 4096 256 512 500 500 0 0 0000 60 150 6 50 xxE1 6 4000 0 0 0 0 0

HC 153R 10 33 0 15 0 0 1364 4096 4096 256 512 500 500 0 0 0000 60 150 6 50 xxE2 6 4000 0 0 0 0 0

HC 203R 20 33 0 20 0 0 1364 4096 4096 256 512 500 500 0 0 0000 60 150 6 50 xxE3 6 4000 0 0 0 0 0

HC 353R 35 33 0 40 0 0 1364 4096 4096 256 512 500 500 0 0 0000 60 150 6 50 xxE4 6 4000 0 0 0 0 0

II - 186

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 SV041 SV042 SV043 SV044 SV045 SV046 SV047 SV048 SV049 SV050 SV051 SV052 SV053 SV054 SV055 SV056 SV057 SV058 SV059 SV060 SV061 SV062 SV063 SV064 SV065 LMCT LMC2 OVS2 OBS1 OBS2 TRUB EC EMGrt PGN1sp PGN2sp DFBT DFBN OD3 ORE EMGx EMGt SHGC SHGCsp TCNV TLMT DA1NO DA2NO DA1MPY DA2MPY

HC 53 05 0000 0003 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 103 10 0000 0003 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 153 20 0000 0003 0040 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 203 35 0000 0003 0040 0000 0 0 0 1024 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 353 45 0000 0003 0040 0000 0 0 0 1024 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 453 70 0000 0003 0040 0000 0 0 0 1024 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 703 90 0000 0003 0040 0000 0 0 0 1024 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 103R 10 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 153R 10 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 203R 20 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HC 353R 35 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 187

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

(b) HA**N series Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 VGN2 SV007 VIL SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 VCS SV030 IVC SV031 OVS1 SV032 TOF HA 40N 05 33 0 150 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xx00 6 4000 0 0 0 0 0 HA 80N 10 33 0 150 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xx01 6 4000 0 0 0 0 0 HA 100N 20 33 0 150 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx02 6 4000 0 0 0 0 0 HA 200N 35 33 0 150 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx03 6 4000 0 0 0 0 0 HA 300N 45 33 0 150 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx04 6 4000 0 0 0 0 0 HA 700N 70 25 0 250 0 0 1364 2048 2048 200 256 500 500 0 0 0000 60 150 6 50 xx05 6 4000 0 0 0 0 0 HA 900N 90 25 0 250 0 0 1364 2048 2048 200 256 500 500 0 0 0000 60 150 6 50 xx06 6 4000 0 0 0 0 0

II - 188

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 DFBT SV052 DFBN SV053 OD3 SV054 ORE SV055 EMGx SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065

HA 40N 05 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 80N 10 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 100N 20 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 200N 35 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 300N 45 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 700N 70 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 900N 90 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 189

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 VGN2 SV007 VIL SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 VCS SV030 IVC SV031 OVS1 SV032 TOF

HA 43N 05 33 0 150 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx80 6 4000 0 0 0 0 0

HA 83N 10 33 0 150 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx81 6 4000 0 0 0 0 0

HA 93N 20 33 0 150 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx8A 6 4000 0 0 0 0 0

HA 103N 35 33 0 150 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx82 6 4000 0 0 0 0 0

HA 203N 45 33 0 150 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx83 6 4000 0 0 0 0 0

HA 303N 70 33 0 150 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx84 6 4000 0 0 0 0 0

HA 703N 90 25 0 250 0 0 1364 2048 2048 200 256 500 500 0 0 0000 60 150 6 50 xx85 6 4000 0 0 0 0 0

II - 190

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 DFBT SV052 DFBN SV053 OD3 SV054 ORE SV055 EMGx SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065

HA 43N 05 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 83N 10 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 93N 20 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 103N 35 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 203N 45 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 303N 70 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 703N 90 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 191

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

Motor

HA 053

HA 13

HA 053N

HA 13N

HA 23N 03 33 0 100 0 0 1364 2048 2048 224 224 500 500 0 0 0000 60 150 6 50 xx8E 6 4000 0 0 0 0 0

HA 33N 03 33 0 100 0 0 1364 2048 2048 224 224 500 500 0 0 0000 60 150 6 50 xx8F 6 4000 0 0 0 0 0

Drive unit 01 01 01 01 capacity SV001 PC1 SV002 PC2 SV003 PGN1 33 33 33 33 SV004 PGN2 0 0 0 0 SV005 VGN1 70 70 70 70 SV006 VGN2 0 0 0 0 SV007 VIL 0 0 0 0 SV008 VIA 1364 1364 1364 1364 SV009 IQA 2048 2048 2048 2048 SV010 IDA 2048 2048 2048 2048 SV011 IQG 256 256 256 256 SV012 IDG 256 256 256 256 SV013 ILMT 500 500 500 500 SV014 ILMTsp 500 500 500 500 SV015 FFC 0 0 0 0 SV016 LMC1 0 0 0 0 SV017 SPEC 0000 0000 0000 0000 SV018 PIT SV019 RNG1 10 10 SV020 RNG2 10 10 SV021 OLT 60 60 60 60 SV022 OLL 150 150 150 150 SV023 OD1 6 6 6 6 SV024 INP 50 50 50 50 SV025 MTYP 338C 338D xx8C xx8D SV026 OD2 6 6 6 6 SV027 SSF1 4000 4000 4000 4000 SV028 0 0 0 0 SV029 VCS 0 0 0 0 SV030 IVC 0 0 0 0 SV031 OVS1 0 0 0 0 SV032 TOF 0 0 0 0 (Note) The HA053 and HA13 are dedicated for the MDS-B-Vx.

II - 192

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

Motor

HA 053

HA 13

HA 053N

HA 13N

HA 23N 03 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 33N 03 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Drive unit 01 01 01 01 capacity SV033 SSF2 0000 0000 0000 0000 SV034 SSF3 0000 0000 0000 0000 SV035 SSF4 0000 0000 0000 0000 SV036 PTYP 0000 0000 0000 0000 SV037 JL 0 0 0 0 SV038 FHz1 0 0 0 0 SV039 LMCD 0 0 0 0 SV040 LMCT 0 0 0 0 SV041 LMC2 0 0 0 0 SV042 OVS2 0 0 0 0 SV043 OBS1 0 0 0 0 SV044 OBS2 0 0 0 0 SV045 TRUB 0 0 0 0 SV046 0 0 0 0 SV047 EC 100 100 100 100 SV048 EMGrt 0 0 0 0 SV049 PGN1sp 15 15 15 15 SV050 PGN2sp 0 0 0 0 SV051 DFBT 0 0 0 0 SV052 DFBN 0 0 0 0 SV053 OD3 0 0 0 0 SV054 ORE 0 0 0 0 SV055 EMGx 0 0 0 0 SV056 EMGt 0 0 0 0 SV057 SHGC 0 0 0 0 SV058 SHGCsp 0 0 0 0 SV059 TCNV 0 0 0 0 SV060 TLMT 0 0 0 0 SV061 DA1NO 0 0 0 0 SV062 DA2NO 0 0 0 0 SV063 DA1MPY 0 0 0 0 SV064 DA2MPY 0 0 0 0 SV065 0 0 0 0 (Note) The HA053 and HA13 are dedicated for the MDS-B-Vx.

II - 193

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

(c) HA**L series Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 VGN2 SV007 VIL SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 VCS SV030 IVC SV031 OVS1 SV032 TOF HA 50L 05 33 0 30 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xx20 6 4000 0 0 0 0 0 HA 100L 10 33 0 30 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xx21 6 4000 0 0 0 0 0 HA 150L 10 33 0 30 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xx2A 6 4000 0 0 0 0 0 HA 200L 20 33 0 30 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xx22 6 4000 0 0 0 0 0 HA 300L 35 33 0 30 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx23 6 4000 0 0 0 0 0 HA 500L 45 33 0 50 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx24 6 4000 0 0 0 0 0 HAA11KL 110 33 0 150 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xx27 6 4000 0 0 0 0 0 HAA15KL 150 33 0 150 0 0 1364 2048 2048 512 512 500 500 0 0 0000 3 150 6 50 xx28 6 4000 0 0 0 0 0

II - 194

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

Motor Drive unit capacity SV033 SSF2 SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 DFBT SV052 DFBN SV053 OD3 SV054 ORE SV055 EMGx SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065

HA 50L 05 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 100L 10 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 150L 10 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 200L 20 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 300L 35 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 500L 45 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HAA11KL 110 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HAA15KL 150 0000 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 195

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

Motor Drive unit capacity SV001 PC1 SV002 PC2 SV003 PGN1 SV004 PGN2 SV005 VGN1 SV006 VGN2 SV007 VIL SV008 VIA SV009 IQA SV010 IDA SV011 IQG SV012 IDG SV013 ILMT SV014 ILMTsp SV015 FFC SV016 LMC1 SV017 SPEC SV018 PIT SV019 RNG1 SV020 RNG2 SV021 OLT SV022 OLL SV023 OD1 SV024 INP SV025 MTYP SV026 OD2 SV027 SSF1 SV028 SV029 VCS SV030 IVC SV031 OVS1 SV032 TOF SV033 SSF2

HA 53L 10 33 0 30 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xx30 6 4000 0 0 0 0 0 0000

HA 103L 20 33 0 30 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xx31 6 4000 0 0 0 0 0 0000

HA 153L 20 33 0 30 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xx3A 6 4000 0 0 0 0 0 0000

HA 203L 35 33 0 30 0 0 1364 2048 2048 512 512 500 500 0 0 0000 60 150 6 50 xx32 6 4000 0 0 0 0 0 0000

HA 303L 45 33 0 30 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx33 6 4000 0 0 0 0 0 0000

HA 503L 70 33 0 50 0 0 1364 2048 2048 256 512 500 500 0 0 0000 60 150 6 50 xx34 6 4000 0 0 0 0 0 0000

II - 196

7.3

7. SERVO PARAMETERS MDS-C1-Vx STANDARD SPECIFICATION (MDS-B-Vx COMPATIBLE)

Motor Drive unit capacity SV034 SSF3 SV035 SSF4 SV036 PTYP SV037 JL SV038 FHz1 SV039 LMCD SV040 LMCT SV041 LMC2 SV042 OVS2 SV043 OBS1 SV044 OBS2 SV045 TRUB SV046 SV047 EC SV048 EMGrt SV049 PGN1sp SV050 PGN2sp SV051 DFBT SV052 DFBN SV053 OD3 SV054 ORE SV055 EMGx SV056 EMGt SV057 SHGC SV058 SHGCsp SV059 TCNV SV060 TLMT SV061 DA1NO SV062 DA2NO SV063 DA1MPY SV064 DA2MPY SV065

HA 53L 10 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 103L 20 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 153L 20 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 203L 35 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 303L 45 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

HA 503L 70 0000 0000 0000 0 0 0 0 0 0 0 0 0 0 100 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

II - 197

7. 7.4

SERVO PARAMETERS SUPPLEMENT

7.4 SUPPLEMENT

7.4.1 D/A OUTPUT SPECIFICATIONS (1) MDS-B-SVJ2 (a) D/A output specifications Item No. of channels Output cycle Output precision Output voltage range Output scale setting Output pins Explanation 2ch 888s (min. value) 8bit -10V to 0 to +10V 1/256 to 128 times CN3 connector MO1 = pin 4 MO2 = pin 14 GND = pin 1,11 Offset amount adjustment function Output clamp function Low path filter function Relay terminal: MR-J2CN3TM Connect from the CN3 connector using the SH21 cable as a lead-in wire.

Function

Option

Pin 1 2 3 4 5 6 7 8 9 10

CN3 Connector Signal Pin Signal LG 11 LG 12 SG 13 MBR MO1 14 MO2 COM 15 MC 16 17 18 19 VDD 20 EMGX

II - 198

7. 7.4

SERVO PARAMETERS SUPPLEMENT

(b) Setting the output data Set the No. of the data to be outputted to each D/A output channel. # 2261 2262 No. SV061 SV062 Abbrev DA1NO DA2NO Parameter name D/A output channel 1 data No. D/A output channel 2 data No.

No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 to 99 100 101 102 103 to

Output data 0V test output Speed feedback Current feedback Speed command Current command V-phase current value W-phase current-value Estimated disturbance torque Collision detection disturbance torque Position feedback (stroke) Position feedback (pulse) Position droop Position droop (x10) Position droop (x100) Feedrate (FT) Feedrate (FT x 10) Model position droop Model position droop (x10) Model position droop (x100) q-axis current cumulative value d-axis current cumulative value Motor load level Amplifier load level Regenerative load level PN bus wire voltage Speed cumulative item Cycle counter Excessive error detection amount Collision detection estimated torque Position command (stroke) Position command (pulse) 5V test output Saw-tooth wave test output Recutangular wave test output Setting prohibited

Standard Output output unit cycle For offset amount adjustment 1000rpm / 2V 888s Stall (rated) 888s 100% / 2V 1000rpm / 2V 888s Stall (rated) 888s 100% / 2V 10A / V 888s 10A / V 888s Stall (rated) 888s 100% / 2V Stall (rated) 888s 100% / 2V 100mm / V 3.55ms 10m / V 3.55ms mm / V 3.55ms 100m / V 3.55ms 10m / V 3.55ms 10000(mm/min) / V 888s 1000(mm/min) / V 888s mm / V 3.55ms 100m / V 3.55ms 10m / V 3.55ms 888s 888s 100% / 5V 113.7ms 100% / 5V 113.7ms 100% / 5V 910.2ms 50V / V (1/50) 888s 888s 0-5V (Regardless 888s of resolution) mm / V 3.55ms Stall (rated) 888s 100% / 2V 100mm / V 3.55ms 10m / V 3.55ms -5 to 5V Cycle: 113.7ms 0 to 5V Cycle: 227.5ms 888s 888s

II - 199

7. 7.4

SERVO PARAMETERS SUPPLEMENT

(c) Setting the output scale When 0 is set, the output will be made with the standard output unit. To change the output unit, set a value other than 0. The scale is set with a 1/256 unit. When 256 is set, the unit will be the same as the standard output. # 2263 2264 No. SV063 SV064 Abbrev DA1MPY DA2MPY Parameter name D/A output channel 1 output scale D/A output channel 2 output scale

(Example 1) When SV061 = 5, SV063 = 2560 The V-phase current value will be output with 1 A/V unit to D/A output ch.1. (Example 2) When SV063 = 11, SV064 = 128 The position droop will be output with a 2mm/Vunit to D/A output ch.2.

II - 200

7. 7.4

SERVO PARAMETERS SUPPLEMENT

(2) MDS-C1-Vx, MDS-B-Vx, MDS-B-Vx4 (a) D/A Output specifications Item No. of channels Output cycle Output precision Output voltage Output scale setting Output pins Explanation 2ch 888s (min. value) 8bit 0V to 2.5V to +5V 1/256 to 128 times CN9 connector MO1 = pin 9 MO2 = pin 19 GND = pin 1,11 Phase current feed back output function L-axis U-phase current FB : pin 7 L-axis V-phase current FB : pin 17 M-axis U-phase current FB : pin 6 M-axis V-phase current FB : pin 16 An drive unit with 2 axes also has 2 channels for D/A output. Therefore, set the output data of the axis (SV061,62), which is not observed, to -1.

Function

Option

CN9 Connector Pin Signal Pin Signal 1 LG 11 LG 2 12 3 13 4 14 5 15 6 MUIFB 16 MVIFB 7 LUIFB 17 LVIFB 8 18 9 MO1 19 MO2 10 20

II - 201

7. 7.4

SERVO PARAMETERS SUPPLEMENT

(b) Setting the output data Set the No. of the data to be outputted to each data D/A output channel. # 2261 2262 No. SV061 SV062 Abbrev DA1NO DA2NO Parameter name D/A output channel 1 data No. D/A output channel 2 data No. Standard setting value of output Standard output Standard Output scale unit output unit cycle (Setting values in SV063, SV064) For a drive unit. with 2 axes (MDS-C1-V2). Set for the parameter of the axis which is not used. 13 (in case of 1000rpm / V 3.55ms 2000rpm) r/min 9 (in case of 1500rpm / V 3.55ms 3000rpm) Stall% Stall% Stall% 131 131 131 Stall 100% / V Stall 100% / V Stall 100% / V 3.55ms 3.55ms 3.55ms

No.

Output data

-1

D/A output non-selected

ch1: Speed feedback 0 ch2: Current command Current command Current feedback Position droop Feedrate (FT) Position command Position feedback Collision detection estimated torque Collision detection disturbance torque Current command (High-speed) Current feedback (High-speed)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

NC display unit / 2

328 (When the display unit=1m)

10m / 0.5V

3.55ms

(NC display unit / 2) 55 / comminucation (When 1m, 3.5ms) cycle 328 (When the display unit=1m) 328 (When the display unit=1m) 131 131

1000 (mm/min) / 0.5V

3.55ms

NC display unit / 2

10m / 0.5V

3.55ms

NC display unit / 2

10m / 0.5V

3.55ms

Stall% Stall%

Stall 100% / V Stall 100% / V

3.55ms 3.55ms

64

Internal unit

65

Internal unit

8 (adjustment 888s required) 8 (adjustment 888s required) (To be continued to the next page)

II - 202

7. 7.4

SERVO PARAMETERS SUPPLEMENT

No.

Output data

Standard output unit

77

Estimated disturbance torque Saw-tooth wave test output Rectangular wave test output 2.5V (data 0) test output

Internal unit

(Continued from the previous page) Standard setting value of output Standard Output scale output unit cycle (Setting values in SV063, SV064) 8 (adjustment 888s required) 0 (256) 0 (256) 0 (256) Cycle: 227.5ms Cycle: 1.7ms 888s 888s 888s

125 126 127

0V to 5V 0V to 5V 2.5V

(c) Setting the output scale # 2263 2264 No. SV063 SV064 Abbrev DA1MPY DA2MPY Parameter name D/A output channel 1 output scale D/A output channel 2 output scale

Usually, the standard setting value is set for the output scale (SV063, SV 064). When 0 is set, the output will be made as well as when 256 is set. DATA x SV063 256 x 5 [V] 256 (8bit) + 2.5 [V] (offset) = Output voltage [V]

(Example) When outputting the current FB with 100%/Vstall (SV061=3, SV063=131) 100 x 131 256 x 5 256 + 2.5 = 3.499 [V]

II - 203

7. 7.4

SERVO PARAMETERS SUPPLEMENT

7.4.2 ELECTRONIC GEARS

By setting the ball screw lead, deceleration ratio (or acceleration ratio), and detector resolution correctly with parameters, the command movement amount and machine end movement amount can be matched. The following parameters are related to these electronic gears, and directly affect the machine operation. Take care to set these correctly. Parameters related to electronic gears SV001 (PC1), SV002 (PC2), SV003 (PGN1)(SV049(PGN1sp)), SV018 (PIT), SV019 (RNG1), SV020 (RNG2) PC1 and PC2 setting range As a principle, the setting range of SV001 (PC1) and SV002 (PC2) is 1 to 30. However, if the following conditions are satisfied, a value higher than 30 can be set. Note that the following conditions must be satisfied even when setting a value between 1 and 30. For semi-closed loop: RNG1 x PC2 PIT x PC1 x IUNIT For closed loop: PGN1 x RNG2 x PC2 30 x RNG1 x PC1

PC1 '' < 32767 / PIT'' / IUNIT'' PC2''' < 32767 / RNG1''' PC1''' < 32767 / RNG1''' / C30'' PC2''' < 32767 / RNG2''' / PGN1'

Meaning of symbols PC1''' PC2'' PIT(') RNG1'(') RNG2'(') PGN1' IUNIT'(') C30'(') Value obtained by dividing PC1. Value obtained by dividing PC2. Value obtained by dividing PIT once (twice). Value obtained by dividing RNG1 once (twice). Value obtained by dividing RNG2 once (twice). Value obtained by dividing PGN1 once (twice). Value obtained by dividing CNC interpolation unit once (twice). Value obtained by dividing a number 30 once (twice).

II - 204

7. 7.4

SERVO PARAMETERS SUPPLEMENT

Example of calculating PC1 and PC2 setting range To use a ball screw lead of 10mm, interpolation unit of 0.5m and OSE104 or OSA104 motor end detector with semi-closed loop. The following parameters are determined by the above conditions. SV018 (PIT) = 10, SV019 (RNG1) = 100, SV020 (RNG2) = 100, IUNIT = 2 Divide the denominator and numerator. PIT' = 1, RGN1' = 10 (Greatest common divisor = 10) IUNIT' = 1, RGN1'' = 5 (Greatest common divisor = 2) Obtain the maximum value of PC1 and PC2 with the calculation expression for the semi-closed loop. PC1' < 32767 / 1 / 1 < 32767 PC2' < 32767 / 5 < 6553 With the above calculations, the setting range for PC1 is 1 to 32767 and for PC2 is 1 to 6553.

To use a rotation table, interpolation unit of 0.5m and OSE104 or OSA104 motor end detector with semi-closed loop. The following parameters are determined by the above conditions. SV018 (PIT) = 360, SV019 (RNG1) = 100, SV020 (RNG2) = 100, IUNIT = 2 Divide the denominator and numerator. PIT' = 18, RGN1' = 5 (Greatest common divisor = 20) Obtain the maximum value of PC1 and PC2 with the calculation expression for the closed loop. PC1' < 32767 / 18 / 2 < 910 PC2' < 32767 / 5 < 6553 With the above calculations, the setting range for PC1 is 1 to 910 and for PC2 is 1 to 6553.

To use a ball screw lead of 10mm, interpolation unit of 0.5m, position loop gain of 33, OSE104 or OSA104 motor end detector with closed loop, and 1m scale machine end detector. The following parameters are determined by the above conditions. SV018 (PIT) = 10, SV019 (RNG1) = 10, SV020 (RNG2) = 100, IUNIT = 2, PGN1 = 33 Divide the denominator and numerator. RNG1' = 1, RNG2' = 10 (Greatest common divisor = 10) C30' = 3, RNG2'' = 1 (Greatest common divisor = 10) C30'' = 1, PGN1' = 11 (Greatest common divisor = 3) Obtain the maximum value of PC1 and PC2 with the calculation expression for the closed loop. PC1' < 32767 / 1 / 1 < 32767 PC2' < 32767 / 1 / 11 < 2978 With the above calculations, the setting range for PC1 is 1 to 32767 and for PC2 is 1 to 2978.

To use a ball screw lead of 10mm, interpolation unit of 0.5m, position loop gain of 33, OSE105 or OSA105 motor end detector with closed loop, and 1m scale machine end detector. The following parameters are determined by the above conditions. SV018 (PIT) = 12, SV019 (RNG1) = 12, SV020 (RNG2) = 1000, IUNIT = 2, PGN1 = 33 Divide the denominator and numerator. RNG1' = 3, RNG2' = 250 (Greatest common divisor = 4) C30' = 3, RNG2'' = 25 (Greatest common divisor = 10) C30'' = 1, PGN1' = 11 (Greatest common divisor = 3) Obtain the maximum value of PC1 and PC2 with the calculation expression for the closed loop. PC1' < 32767 / 3 / 1 < 10922 PC2' < 32767 / 25 / 11 < 119 With the above calculations, the setting range for PC1 is 1 to 10922 and for PC2 is 1 to 199.

II - 205

7. 7.4

SERVO PARAMETERS SUPPLEMENT

7.4.3 LOST MOTION COMPENSATION

When the motor is to rotate in the clockwise direction (looking from the load side) at the command for the + direction, the command direction is CW. Conversely, when the motor is to rotate in the counterclockwise direction, the command direction is CCW. This rotation direction can be set with the CNC machine parameters. Note that the meaning of the will differ for some servo parameters according to this motor rotation direction. The servo parameters affected by CW/CCW are shown below. SV016 (LMC1), SV041 (LMC2) SV031 (OVS1), SV042 (OVS2) (When different values are set for SV016 and SV041) (When different values are set for SV031 and SV042)

<Example> If the lost motion compensation amount is to be changed according to the direction, the compensation amount at the quadrant changeover point of each arc where the lost motion compensation is applied will be as shown below according to the command polarity. CW A B C D X: SV041 Y: SV016 X: SV016 Y: SV041 CCW X: SV016 Y: SV041 X: SV041 Y: SV016 +Y The Y axis command direction changes from the + to direction. The X axis command direction changes from the + to direction.

-X The X axis command direction changes from the to + direction. B

+X

-Y

The Y axis command direction changes from the to + direction.

(Note) The setting value for the parameter is 0 or -1, the compensation amount is determined as shown below. Setting value for SV016 (Setting value for SV031) 0 n 0 n n -1 Setting value for SV041 (Setting value for SV041) 0 0 m m -1 m Compensation amount in + direction No compensation n m n n No compensation Compensation amount in - direction No compensation n m m No compensation m

II - 206

8.1

8. MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE BASE SPECIFICATIONS PARAMETERS

8.

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

The spindle parameter setting and display method will differ according to the CNC being used, so refer to Instruction Manual for each CNC and the following spindles. MELDAS AC Servo and Spindle MDS-A Series MDS-B Series Specifications Manual .......... BNP-B3759

8.1 MDS-B-SP/SPH,SPJ2 SPINDLE BASE SPECIFICATIONS PARAMETERS

For parameters indicated with a (PR) in the table, turn the NC power OFF after setting. The setting is validated after the power is turned ON again. No. 3001 slimit 1 3002 3003 3004 2 3 4 Maximum Set maximum spindle rotation speed with gears rotation speed 00, 01, 10, 11. Set to slimt smax. By comparing the S command value and the value of gear 1 to 4, a spindle gear shift command will be output automatically. Shift rotation speed Set spindle speed for gear shifting with gears 00, 0 to 32767 (r/min) 01, 10, 11. (Note) Setting too large value may cause a gear nicks when changing gears. Set maximum spindle rotation speed during tap cycle with gears 00, 01, 10, 11. 0 to 99999 (r/min) Items Limit rotation speed Details Set spindle rotation speed for maximum motor rotation speed with gears 00, 01, 10, 11. (Set the spindle speed for the S analog output 10V.) Setting range (Unit) 0 to 99999 (r/min)

3005 smax 1 3006 3007 3008 3009 ssift 3010 3011 3012 2 3 4 1 2 3 4

3013 stap 1 3014 3015 3016 2 3 4

Tap rotation speed

3017 stapt 1 3018 3019 3020 2 3 4

Tap time constant

Set time constants for constant inclination synchronous tap cycles for gears 00, 01, 10, 11 (linear acceleration/ deceleration pattern).

1 to 5000 (ms)

II - 207

8.1

8. MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE BASE SPECIFICATIONS PARAMETERS

Relationship between spindle limit rotation speed and maximum spindle rotation speed
Output voltage (V) 10V

Spindle rotation speed (r/min) 0 smax1 slimt1 smax2 slimt2 smax(n) slimt(n)

Limit rotation speed of gear 1 (Parameter setting) Maximum rotation speed of gear 1 (Parameter setting) Set "0" for any unused gear.

Relation between the spindle limit rotation speed and the spindle tap time constant (for the constant inclination synchronous tap cycle)
Spindle rotation speed (r/min) slimt(n) slimt(n) slimt2 slimt1 S command Spindle rotation speed (r/min)

Time (ms) 0 stapt1 stapt2 stapt(n) Execution time constant stapt(n)

Time (ms)

II - 208

8.1

8. MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE BASE SPECIFICATIONS PARAMETERS

# 3021 sori

Items

Details

Setting range (Unit)

Orientation rotation Set the spindle orientation rotation speed. 0 to 32767 (r/min) speed Set the rotation speed for when the spindle rotates at the constant rotation speed. Encoder gear ratio Set the gear ratio of the spindle to the encoder. 0: 1/1 1: 1/2 2: 1/4 3: 1/8

3022

sgear

3023

smini

Minimum rotation speed

Set the minimum rotation speed of the 0 to 32767 (r/min) spindle. If an S command instructs the rotation speed below this setting, the spindle rotates at the minimum rotation speed set by this parameter. Set the type of the spindle to be connected. 0 to 5 0: No connection with the spindle 1: Serial connection (bus) 2 to 5: Analog output 0 to 2

3024 (PR)

sout

Spindle connection

3025

enc-on

Spindle encoder

3026

cs_ori

3027

cs_syn

Set connection information of the spindle encoder. 0: No connection 1: Spindle connection (Spindle encoder connection check function valid.) 2: Serial connection of encoder Selection of 0: Perform orientation using the winding winding in selected when the orientation orientation mode command is issued. 1: Use winding L whenever the orientation command is issued. Selection of 0: The winding H/L is selected by the winding in spindle actual spindle motor rotation speed synchronous mode (calculated from commanded rotation speed) when spindle synchronous control starts. (The winding is not switched during synchronous control. The control is carried out with the winding selected at start.) If the actual spindle motor rotation speed is less than SP020, the winding L is selected, and if more than the value, the winding H is selected. 1: Use winding H whenever the spindle synchronous command is issued. L system tap cycle Set the M code of the spindle forward spindle forward run/ run/reverse run command. reverse run M High-order three digits: The spindle command forward run command's M code is set. Low-order three digits: The spindle reverse run command's M code is set.

0/1

0/1

3028

sprcmm

0 to 999999

II - 209

8.1

8. MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE BASE SPECIFICATIONS PARAMETERS

# 3029 tapsel

Items Asynchronous tap gear selection

Details Specify whether to use the tap rotation speed or maximum rotation speed for the gear that is selected when an asynchronous tap command is issued. 0: Tap rotation speed 1: Maximum rotation speed This parameter is valid only when the M-function synchronous tap cycle enable parameter (#1272 ext08 bit1) is ON. Select whether to use magnetic bearings. 0: Magnetic bearings invalid 1: Magnetic bearings valid

Setting range (Unit) 0/1

3030 (PR) 3031 (PR)

mbsel

Selection of magnetic bearings Amplifier I/F channel No. (spindle)

0/1

smcp_no

Using a 4-digit number, set the amplifier 0000 interface channel No. and which axis in that 0101 to 0107 channel is to be used when connecting a 0201 to 0207 spindle amplifier. High-order two digits : Amplifier interface channel No. Low-order two digits : Axis No. When using the conventional fixed layout, set all axes to "0000". Set "0000" when using an analog spindle. Using a 4-digit number, set the amplifier 0000 interface channel No. and which axis in that 0101 to 0107 channel is to be used when connecting a 0201 to 0207 magnetic bearing amplifier. High-order two digits : Amplifier interface channel No. Low-order two digits : Axis No. When using the conventional fixed layout, set all axes to "0000".

3032 (PR)

mbmcp_no

Amplifier I/F channel No. (magnetic bearing)

3037 3038 3039 3040 3041 3042 3043 3044 3045 3046 3047 3048

taps21 22 23 24 tapt 21 22 23 24 tapt 31 32 33 34

Synchronous tap Set the spindle rotation speed at which the 0 to 99999 (r/min) switching spindle step-2 acceleration/deceleration time speed 2 constant is to be switched at gear 00, 01, 10, or 11. Synchronous tap Set the time constant to reach synchronous 1 to 5000 (ms) switching time tap switching spindle rotation speed 2 constant 2 (#3037 to #3040) at gear 00, 01, 10, or 11.

Synchronous tap Set the time constant to reach the 1 to 5000 (ms) switching time maximum rotation speed (#3005 to #3008) constant 3 at gear 00, 01, 10, or 11.

II - 210

8.1

8. MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE BASE SPECIFICATIONS PARAMETERS

# 3049 spt

Items Spindle synchronization acceleration/ deceleration time constant Spindle synchronization rotation speed attainment level

Details

Setting range (Unit)

Set the acceleration/deceleration time 0 to 9999 (ms) constant for when the spindle synchronization command's rotation speed changes during spindle synchronous control. The spindle rotation speed synchronization 0 to 4095 (pulse) complete signal will turn ON when the (1 pulse = 0.088) difference of the reference spindle and synchronous spindle actual rotation speeds is less than the level set for the synchronous spindle rotation speed command value during spindle synchronous control. 0 to 4095 (pulse) (1 pulse = 0.088)

3050

sprlv

3051

spplv

Spindle phase The spindle phase synchronization synchronizacomplete signal will turn ON when the tion attainment level phase difference of the reference spindle and synchronous spindle is less than the set level during spindle phase synchronization control. Spindle motor spindle relative polarity

3052

spplr

Set the spindle motor and spindle's relative 0: Positive polarity polarity. 1: Negative polarity Spindle CW rotation at motor CW rotation: Positive polarity Spindle CCW rotation at motor CW rotation: Negative polarity Set the deviation amount from the spindle's 0 to 359999 (1/1000) reference position to the spindle encoder's Z phase. The deviation amount is obtained using the clockwise direction looking from the front of the spindle as the positive direction.

3053

sppst

Spindle encoder Z -phase position

3054

sptc1

Spindle Set the spindle speed for changing the 1st 0 to 99999 (r/min) synchronizastep's acceleration/deceleration time tion multi-step constant. acceleration/ deceleration changeover speed 1

II - 211

8.1

8. MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE BASE SPECIFICATIONS PARAMETERS

# 3055 sptc2

Items Spindle synchronization multi-step acceleration/ deceleration changeover speed 2 Spindle synchronization multi-step acceleration/ deceleration changeover speed 3 Spindle synchronization multi-step acceleration/ deceleration changeover speed 4 Spindle synchronization multi-step acceleration/ deceleration changeover speed 5 Spindle synchronization multi-step acceleration/ deceleration changeover speed 6

Details

Setting range (Unit)

Set the spindle speed for changing the 2nd 0 to 99999 (r/min) step's acceleration/deceleration time constant.

3056

sptc3

Set the spindle speed for changing the 3rd 0 to 99999 (r/min) step's acceleration/deceleration time constant.

3057

sptc4

Set the spindle speed for changing the 4th 0 to 99999 (r/min) step's acceleration/deceleration time constant.

3058

sptc5

Set the spindle speed for changing the 5th 0 to 99999 (r/min) step's acceleration/deceleration time constant.

3059

sptc6

Set the spindle speed for changing the 6th 0 to 99999 (r/min) step's acceleration/deceleration time constant.

II - 212

8.1

8. MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE BASE SPECIFICATIONS PARAMETERS

# 3060 sptc7

Items Spindle synchronization multi-step acceleration/ deceleration changeover speed 7

Details Set the spindle speed for changing the 7th step's acceleration/deceleration time constant.

Setting range (Unit) 0 to 99999 (r/min)

3061

spdiv1

Magnification for time Set the acceleration/deceleration time 0 to 127 constant changeover constant between the spindle speed 1 synchronization multi-step acceleration/deceleration changeover speed 1 (sptc1) to the spindle synchronization multi-step acceleration/ deceleration changeover speed 2 (sptc2) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt). Magnification for time Set the acceleration/deceleration time 0 to 127 constant changeover constant between the spindle speed 2 synchronization multi-step acceleration/deceleration changeover speed 2 (sptc2) to the spindle synchronization multi-step acceleration/deceleration changeover speed 3 (sptc3) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt). Magnification for time Set the acceleration/deceleration time 0 to 127 constant changeover constant between the spindle speed 3 synchronization multi-step acceleration/deceleration changeover speed 3 (sptc3) to the spindle synchronization multi-step acceleration/deceleration changeover speed 4 (sptc4) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt). Magnification for time Set the acceleration/deceleration time 0 to 127 constant changeover constant between the spindle speed 4 synchronization multi-step acceleration/deceleration changeover speed 4 (sptc4) to the spindle synchronization multi-step acceleration/deceleration changeover speed 5 (sptc5) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt). Magnification for time Set the acceleration/deceleration time 0 to 127 constant changeover constant between the spindle speed 5 synchronization multi-step acceleration/deceleration changeover speed 5 (sptc5) to the spindle synchronization multi-step acceleration/deceleration changeover speed 6 (sptc6) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt).

3062

spdiv2

3063

spdiv3

3064

spdiv4

3065

spdiv5

II - 213

8.1

8. MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE BASE SPECIFICATIONS PARAMETERS

# 3066 spdiv6

Items Magnification for time constant changeover speed 6

Details Set the acceleration/deceleration time constant between the spindle synchronization multi-step acceleration/deceleration changeover speed 6 (sptc6) to the spindle synchronization multi-step acceleration/deceleration changeover speed 7 (sptc7) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt).

Setting range (Unit) 0 to 127

3067

spdiv7

Magnification for time constant changeover speed 7

Set the acceleration/deceleration time 0 to 127 constant for the spindle synchronization multi-step acceleration/ deceleration changeover speed 7 (sptc7) and higher as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt).

3068

symtm1

Phase synchroniza- Set the time to confirm that synchronization 0 to 9999 (ms) tion start is attained before phase synchronization confirmation time control is started. When "0" is set, the time will be 2 seconds. When "100" or less is set, the time will be 100ms. Phase synchroniza- Set the time to wait for phase 0 to 9999 (ms) tion end synchronization control to end as the time confirmation time for the rotation speed to reach the attainment range. When "0" is set, the time will be 2 seconds. When "100" or less is set, the time will be 100ms. Phase synchroniza- Set the fluctuation amount to change the 0 to 100 (%) tion speed synchronous spindle rotation speed during phase synchronization control as the command speed and rate. When "0" is set, the amount will be 100%. (Not used.) (Not used.)

3069

symtm2

3070

syprt

3071 3072

II - 214

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

8.2 MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

For parameters marked with a (PR) in the tables, turn the NC power OFF after setting. The parameters will be valid after the power is turned ON again. The valid spindle parameters will differ according to the motor and amplifier type. Follow the correspondence table given below, and set the correct parameters. : Valid, : Fixed value Corresponding model MDS-B-SP/SPH MDS-B-SPJ2 Parameter SP043 SP044 SP045 SP046 SP047 SP048 SP049 SP050 SP051 SP052 SP053 SP054 SP055 SP056 SP057 SP058 SP059 SP060 SP061 SP062 SP063 SP064 SP065 SP066 SP067 SP068 SP069 SP070 SP071 SP072 SP073 SP074 SP075 SP076 SP077 SP078 SP079 SP080 SP081 SP082 SP083 SP084 Corresponding model MDS-B-SP/SPH MDS-B-SPJ2

Parameter SP001 SP002 SP003 SP004 SP005 SP006 SP007 SP008 SP009 SP010 SP011 SP012 SP013 SP014 SP015 SP016 SP017 SP018 SP019 SP020 SP021 SP022 SP023 SP024 SP025 SP026 SP027 SP028 SP029 SP030 SP031 SP032 SP033 SP034 SP035 SP036 SP037 SP038 SP039 SP040 SP041 SP042

II - 215

8. 8.2 : Valid,

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

: Fixed value Corresponding model Parameter MDS-B-SP/SPH MDS-B-SPJ2 SP085 SP086 SP087 SP088 SP089 SP090 SP091 SP092 SP093 SP094 SP095 SP096 SP097 SP098 SP099 SP100 SP101 SP102 SP103 SP104 SP105 SP106 SP107 SP108 SP109 SP110 SP111 SP112 SP113 SP114 SP115 SP116 SP117 SP118 SP119 SP120 SP121 SP122 SP123 SP124 SP125 SP126 SP127 SP128 SP129 SP130 SP131

Parameter SP132 SP133 SP134 SP135 SP136 SP137 SP138 SP139 SP140 SP141 SP142 SP143 SP144 SP145 SP146 SP147 SP148 SP149 SP150 SP151 SP152 SP153 SP154 SP155 SP156 SP157 SP158 SP159 SP160 SP161 SP162 SP163 SP164 SP165 SP166 SP167 SP168 SP169 SP170 SP171 SP172 SP173 SP174 SP175 SP176 SP177 SP178

Corresponding model MDS-B-SP/SPH MDS-B-SPJ2

II - 216

8. 8.2 : Valid,

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

: Fixed value Corresponding model Parameter MDS-B-SP/SPH MDS-B-SPJ2 SP179 SP180 SP181 SP182 SP183 SP184 SP185 SP186 SP187 SP188 SP189 SP190 SP191 SP192 SP193 SP194 SP195 SP196 SP197 SP198 SP199 SP200 SP201 SP202 SP203 SP204 SP205 SP206 SP207 SP208 SP209 SP210 SP211 SP212 SP213 SP214 SP215 SP216 SP217 SP218 SP219 SP220 SP221 SP222 SP223 SP224 SP225

Parameter SP226 SP227 SP228 SP229 SP230 SP231 SP232 SP233 SP234 SP235 SP236 SP237 SP238 SP239 SP240 SP241 SP242 SP243 SP244 SP245 SP246 SP247 SP248 SP249 SP250 SP251 SP252 SP253 SP254 SP255 SP256 SP257 SP258 SP259 SP260 SP261 SP262 SP263 SP264 SP265 SP266 SP267 SP268 SP269 SP270 SP271 SP272

Corresponding model MDS-B-SP/SPH MDS-B-SPJ2

II - 217

8. 8.2 : Valid,

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

: Fixed value Corresponding model Parameter MDS-B-SP/SPH MDS-B-SPJ2 SP273 SP274 SP275 SP276 SP277 SP278 SP279 SP280 SP281 SP282 SP283 SP284 SP285 SP286 SP287 SP288 SP289 SP290 SP291 SP292 SP293 SP294 SP295 SP296 SP297 SP298 SP299 SP300 SP301 SP302 SP303 SP304 SP305 SP306 SP307 SP308 SP309 SP310 SP311 SP312 SP313 SP314 SP315 SP316 SP317 SP318 SP319

Parameter SP320 SP321 SP322 SP323 SP324 SP325 SP326 SP327 SP328 SP329 SP330 SP331 SP332 SP333 SP334 SP335 SP336 SP337 SP338 SP339 SP340 SP341 SP342 SP343 SP344 SP345 SP346 SP347 SP348 SP349 SP350 SP351 SP352 SP353 SP354 SP355 SP356 SP357 SP358 SP359 SP360 SP361 SP362 SP363 SP364 SP365 SP366

Corresponding model MDS-B-SP/SPH MDS-B-SPJ2

II - 218

8. 8.2 : Valid,

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

: Fixed value Corresponding model Parameter MDS-B-SP/SPH MDS-B-SPJ2 SP367 SP368 SP369 SP370 SP371 SP372 SP373 SP374 SP375

Parameter SP376 SP377 SP378 SP379 SP380 SP381 SP382 SP383 SP384

Corresponding model MDS-B-SP/SPH MDS-B-SPJ2

II - 219

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

For parameters marked with a (PR) in the tables, turn the NC power OFF after setting. The parameters will be valid after the power is turned ON again. The "fixed control constants" and "fixed control bits" in this section are set by Mitsubishi.

! CAUTION
!

In the explanation on bits, set all bits not used, including blank bits, to 0. Setting range Standard setting 100

No. 3201

Items SP001 PGM Magnetic detector and motor builtin encoder orientationmode position loop gain Encoder orientation-mo de position loop gain

Details

As the set value is larger, the orientation time 0 to 1000 becomes shorter and servo rigidity is (0.1 1/s) increased. On the contrary, however, vibration is increased and the machine becomes likely to overshoot. As the set value is larger, the orientation time 0 to 1000 becomes shorter and servo rigidity is (0.1 1/s) increased. On the contrary, however, vibration is increased and the machine becomes likely to overshoot. Set the position loop gain in C-axis 1 to 100 non-cutting mode. (1/s) During non-cutting (rapid traverse, etc.) with the C axis control, this position loop gain setting is valid. Set the position error range in which an 1 to 2880 orientation completion signal is output. (1/16) Set the motor speed limit value to be used when the speed loop is changed to the position loop in orientation mode. When this parameter is set to "0", SP017 (TSP) becomes the limit value. As the set value is larger, the orientation time becomes shorter. On the contrary, however, the machine becomes likely to overshoot. For MDS-B-SP/SPH Set the stop position for orientation. (i) Motor built-in encoder, encoder: Set the value by dividing 360 by 4096. (ii) Magnetic detector: Divide 5 to +5 by 1024 and put 0 for 0. For others Set the stop position for orientation. Set the value by dividing 360 by 4096. Not used. Set to "0". Set the spindle position loop gain in synchronous tapping mode.

3202

SP002 PGE

100

3203

SP003 PGC0 C-axis non-cutting position loop gain Orientation in-position width Orientation SP005 OSP mode changing speed limit value Orientation SP006 CSP mode deceleration rate SP007 OPST In-position shift amount for orientation SP004 OINP

15

3204

16

3205 (PR)

0 to 32767 0 (r/min)

3206

1 to 1000

20

3207

(i) 0 to 4095 (ii) 512 to 512

0 to 4095

3208 3209

SP008 SP009 PGT

3210

SP010 PGS

Synchronous tapping position loop gain Spindle synchronous position loop gain

0 1 to 100 (1/s)

0 15

Set the spindle position loop gain in spindle synchronization mode.

1 to 100 (1/s)

15

II - 220

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3211

Items SP011 WCLP2 Turret indexing clamp speed 2

Details Set the turret indexing clamp speed for when the door interlock spindle speed clamp signal is ON. This parameter is used only with SPH. (Note) This is valid only when "SP097 (SPEC0)" bit8 is set to 1. Use not possible.

Setting range 0 to 32767 (r/min)

Standard setting

3212 to 3216 3217 (PR) 3218 (PR) 3219 (PR)

SP012 to SP016 SP017 TSP SP018 ZSP SP019 CSN1

Maximum motor Set the maximum motor speed of the speed spindle. Motor zero speed Set the motor speed for which zero-speed output is performed.

1 to 32767 (r/min) 1 to 1000 (r/min) 0 to 32767 (10ms)

6000 50 30

Speed cushion 1 Set the time constant for a speed command from "0" to the maximum speed. (This parameter is invalid in position loop mode.)

3220 (PR)

SP020 SDTS

Speed detection Set the motor speed so for which speed 0 to 32767 set value detection output is performed. (r/min) Usually, the setting value is 10% of SP017 (TSP). Torque limit 1 Set the torque limit rate for torque limit signal 001. 0 to 120 (%)

600

3221 3222 (PR)

SP021 TLM1

10 63

SP022 VGNP1 Speed loop gain proportional term under speed control SP023 VGNI1 Speed loop gain integral term under speed control SP024 SP025 GRA1 SP026 GRA2 SP027 GRA3 SP028 GRA4 SP029 GRB1 SP030 GRB2 SP031 GRB3 SP032 GRB4 Spindle gear teeth count 1 Spindle gear teeth count 2 Spindle gear teeth count 3 Spindle gear teeth count 4

Set the speed loop proportional gain in 0 to 1000 speed control mode. (1/s) When the gain is increased, response is improved but vibration and sound become larger. Set the speed loop integral gain in speed control mode. Usually, set a value in proportion to SP022 (VGNP1). Not used. Set to "0". Set the number of gear teeth of the spindle corresponding to gear 000. Set the number of gear teeth of the spindle corresponding to gear 001. Set the number of gear teeth of the spindle corresponding to gear 010. Set the number of gear teeth of the spindle corresponding to gear 011. 0 to 1000 (0.1 1/s)

3223 (PR)

60

3224 3225 (PR) 3226 (PR) 3227 (PR) 3228 (PR) 3229 (PR) 3230 (PR) 3231 (PR) 3232 (PR)

0 1 to 32767 1 to 32767 1 to 32767 1 to 32767 1 to 32767 1 to 32767 1 to 32767 1 to 32767

0 1 1 1 1 1 1 1 1

Motor shaft gear Set the number of gear teeth of the teeth count 1 motor shaft corresponding to gear 000. Motor shaft gear Set the number of gear teeth of the teeth count 2 motor shaft corresponding to gear 001. Motor shaft gear Set the number of gear teeth of the teeth count 3 motor shaft corresponding to gear 010. Motor shaft gear Set the number of gear teeth of the teeth count 4 motor shaft corresponding to gear 011.

II - 221

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items Spindle function 1

Details Set the spindle function 1 in bit units.

F poff 7 E hzs 6 D C ront 4 B A 9 8

Setting range

Standard setting

3233 SP033 SFNC1 (PR)

0000 to 0000 FFFF HEX setting

2 sftk

1 0 dflt 1a2m

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 0 1a2m 1 amplifier 2 motor function: Invalid 1 dflt Default motor: Main 2 sftk SF-TK card invalid 3 4 5 6 7 8 9 A This is a fixed control bit. B C ront D E hzs F poff Meaning when set to 1 1 amplifier 2 motor function: Valid Default motor: Sub SF-TK card valid

3234 SP034 SFNC2 (PR)

Spindle function 2

For MDS-B-SP/SPH Set the spindle function 2 in bit units.

F E D C B A 9 8

0000 to 0000 FFFF HEX setting

3 2 1 0 mkc2 mkch invm mts1

Meaning when set to 1 Special motor constant setting valid A general-purpose motor FV control valid Winding switch function valid

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 0 mts1 Special motor constant invalid 1 invm A general-purpose motor FV control invalid 2 mkch Winding switch function invalid 3 mkc2 This is a fixed control bit. 4 5 6 7 8 9 A B C D E F

II - 222

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items For MDS-B-SPJ2

Details

Setting range

Standard setting

bit Name Meaning when set to 0 Meaning when set to 1 0 mts1 Special motor constant Special motor constant invalid setting valid 1 2 3 4 5 6 7 8 9 A B C D E F

3235 (PR)

SP035 SFNC3 Spindle function 3

For MDS-B-SP/SPH Set the spindle function 3 in bit units.

0000 to FFFF HEX setting

8

0000

3 2 1 0 lbsd hbsd lwid hwid

Meaning when set to 1 H-coil wide-range constant output valid L-coil wide-range constant output valid H-coil base slide valid L-coil base slide valid

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 hwid H-coil wide-range 0 constant output invalid lwid L-coil wide-range 1 constant output invalid 2 hbsd H-coil base slide invalid 3 lbsd L-coil base slide invalid 4 5 6 7 8 (Used with SPJ.) 9 A B C D E F

II - 223

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items For MDS-B-SPJ2

Details

Setting range

Standard setting

Set the spindle function 3 in bit units.

F E D C B A 9 8

0000 to 0000 FFFF HEX setting

2 hbsd

0 hwid

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 hwid H-coil wide-range 0 constant output invalid 1 2 hbsd H-coil base slide invalid 3 4 5 6 7 8 9 A B C D E F Meaning when set to 1 H-coil wide-range constant output valid H-coil base slide valid

3236 SP036 SFNC4 (PR)

Spindle function 4

Set the spindle function 4 in bit units.

F E D C B A 9 8 dslm dssm

5 4 3 2 1 0 enc2 enc1 mag2 mag1 plg2 plg1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 0 plg1 PLG of motor 1 valid 1 plg2 PLG of motor 2 valid 2 mag1 MAG of motor 1 valid 3 mag2 MAG of motor 2 valid 4 enc1 ENC of motor 1 valid 5 enc2 ENC of motor 2 valid 6 7 8 dssm Speedometer valid 9 dslm Load meter valid A B C D E F Meaning when set to 1 PLG of motor 1 invalid PLG of motor 2 invalid MAG of motor 1 invalid MAG of motor 2 invalid ENC of motor 1 invalid ENC of motor 2 invalid

Speedometer invalid Load meter invalid

II - 224

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items

Details For MDS-B-SP/SPH Set the spindle function 5 in bit units.

F E splg dplg 7 6 D C B A 9 8 noplg nsno nosg 2 1 0 plgo mago enco

Setting range

Standard setting

3237 SP037 SFNC5 Spindle (PR) function 5

0000 to 0000 FFFF HEX setting

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 enco Encoder orientation Encoder orientation 0 invalid valid 1 2 3 4 5 6 7 8 9 A B C D E F mago Magnetic detector orientation invalid plgo PLG orientation invalid Magnetic detector orientation valid PLG orientation valid

No-signal detection type Monitoring only in (Always monitoring) position loop or orientation-mode nsno Fixed control bit noplg Fixed control bit

nosg

dplg splg

Fixed control bit Fixed control bit

(Note) For bit0 to 2, do not set two bits or more to "1" at the same time.

For MDS-B-SPJ2 Set the spindle function 5 in bit units.

F E D C B A 9 8 nstv 0 enco

0000 to 0000 FFFF HEX setting

2 plgo

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 0 enco Encoder orientation invalid 1 2 plgo PLG orientation invalid 3 4 5 6 7 nstv No-signal detection type 8 (Always monitoring) 9 A B C D E F Meaning when set to 1 Encoder orientation valid PLG orientation valid

Monitoring only in position loop or orientation-mode

II - 225

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3238 (PR)

Items SP038 SFNC6 Spindle function 6

Details For MDS-B-SP/SPH Set the spindle function 6 in bit units.

F oplp E lmx D C B A 9 8 iqsv XFzs dcsn lmnp pl80 sdt2 4 tdn 3 2 plg2 pftm 1 0 alty

Setting range 0000 to FFFF HEX setting

Standard setting 0000

7 6 5 vfbs orm adin

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 alty Deceleration stop during 0 special alarm invalid 1 pftm Encoder feedback serial 2 communication invalid plg2 Semi-closed pulse 3 output signal 2 invalid 4 tdn Fixed control bit 5 adin orm Orientation start memo 6 invalid 7 vfbs 8 sdt2 9 pl80 A lmnp Fixed control bit B dcsn C XFzs D iqsv E lmx oplp Open loop operation F invalid Meaning when set to 1 Deceleration stop during special alarm valid Encoder feedback serial communication valid Semi-closed pulse output signal 2 valid

Orientation start memo valid

Open loop operation valid

For MDS-B-SPJ2
bit Name Meaning when set to 0 alty Deceleration stop during 0 special alarm invalid 1 pftm Thread cutting position 2 data invalid 3 4 5 6 7 8 9 A B C D E oplp Open loop operation F invalid Meaning when set to 1 Deceleration stop during special alarm valid Thread cutting position data valid

Open loop operation valid

II - 226

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3239 (PR)

Items SP039 ATYP Amplifier type

Details For MDS-B-SP/SPH Set the amplifier type. Set each amplifier type or "0". This parameter corresponds to MDS-A-SP (version A2 or above) and MDS-B-SP.
Parameter setting 0000 0001 0002 0003 0004 0005 0006 0007 0008 0009 000A 000B 000C 000D 000E 000F 0010 Amplifier type -SP-075 SP-15 SP-22 SP-37 SP-55 SP-75 SP-110 SP-150 SP-185 SP-220 SP-260 SP-300 CSP-370 CSP-450 SP-04 SP-550

Setting range 0000 to FFFF HEX setting

Standard setting 0000

For MDS-B-SPJ2 Set the amplifier type. Set each amplifier type or "0". This parameter corresponds to MDS-B-SPJ2.
Parameter setting 0000 0001 0002 0003 0004 0005 0006 0007 0008 0009 Amplifier type -SPJ2-02 SPJ2-04 SPJ2-075 SPJ2-15 SPJ2-22 SPJ2-37 SPJ2-55 SPJ2-75 SPJ2-110/110C

II - 227

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items Motor type

Details For MDS-B-SP/SPH

Setting range

Standard setting 0000

3240 SP040 MTYP (PR)

0000 to FFFF This parameter is valid when SP034 (SFNC2) HEX bit0 is set to "0". setting Set the appropriate motor number from the standard motors listed below.
Parameter setting 0000 0001 0002 0003 0004 0005 0006 0007 0008 0009 000A 000B 000C 000D 000E 000F 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 001A 001B 001C 001D 001E 001F Motor type Maximum speed 10000 r/min 10000 r/min 8000 r/min 8000 r/min 6000 r/min 6000 r/min 6000 r/min 4500 r/min 4500 r/min 4500 r/min Corresponding amplifier SP-22 SP-37 SP-55 SP-75 SP-110 SP-150 SP-185 SP-220 SP-260 SP-300

SJ-2.2A SJ-3.7A SJ-5.5A SJ-7.5A SJ-11A SJ-15A SJ-18.5A SJ-22A SJ-26A SJ-30A

SJ-N0.75A SJ-N1.5A SJ-N2.2A SJ-N3.7A SJ-N5.5A SJ-N7.5A

10000 r/min 10000 r/min 10000 r/min 10000 r/min 8000 r/min 8000 r/min

SP-075 SP-15 SP-22 SP-37 SP-55 SP-75

SJ-J2.2A SJ-J3.7A SJ-J5.5A SJ-J7.5A

10000 r/min 10000 r/min 8000 r/min 8000 r/min

SP-22 SP-37 SP-55 SP-75

For MDS-B-SPJ2 This is valid when SP034 (SFNC2) bit 0 is set to 0. Refer to the following standard motors, and set the applicable motor number.
Paramete r setting 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 SJ-P0.2A SJ-P0.4A SJ-P0.75A SJ-P1.5A SJ-P2.2A SJ-P3.7A SJ-PF5.5-01 SJ-PF7.5-01 SJ-PF11-01 10000 r/min SPJ2-02 10000 r/min SPJ2-04 10000 r/min SPJ2-075 10000 r/min SPJ2-15 8000 r/min SPJ2-22 8000 r/min SPJ2-37 8000 r/min SPJ2-55 8000 r/min SPJ2-75 6000 r/min SPJ2-110/110C Motor type Maximum speed Corresponding amplifier

II - 228

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3241 (PR)

Items SP041 PTYP

Details

Setting range

Standard setting

Power When this unit is a signal connection axis with 0000 to 0000 supply type power supply unit, set this parameter. FFFF Set "0" for this parameter for the unit which is HEX setting not a signal connection axis. For MDS-B-SP/SPH
bit Name Meaning when set to 0 Meaning when set to 1 0 ptyp Set the power supply type. (Select the type from the following table and set.) 1 Power 2 ptyp Power supply ptyp type supply type 3 00 Not connected 81 CR-10 4 04 CV-37 82 CR-15 06 CV-55 83 CR-22 5 08 CV-75 84 CR-37 6 11 CV-110 86 CR-55 15 CV-150 88 CR-75 7 19 CV-185 89 CR-90 22 CV-220 26 CV-260 30 CV-300 37 CV-370 (Note 1) When using an external emergency stop in the MDS-B-CV, set a value of the above setting values with "40" added. (Example) When using an external emergency stop in CV-260, setting value = 0026 + 0040 = 0066 8 9 A B rtyp Set "0" if the power supply unit is a current regeneration type. If the power supply unit is a resistance regeneration type, set the type of resistance being used. (Select the type from the following table and set.)
rtyp 00 01 02 03 04 05 06 07 08 09 External regenerative resistance type Not connected power supply GZG200W260HMJ GZG300W130HMJ2 MR-RB30 MR-RB50 GZG200W200HMJ3 GZG300W200HMJ3 R-UNIT-1 R-UNIT-2 R-UNIT-3 ResistWatts ance (W) value () 26 26 13 13 6.7 6.7 30 15 15 80 150 300 500 350 500 700 700 2.1K

C D E F

amp

Set the driver model number. 0: MDS-A-V1/V2/SP, MDS-B-V1/V2/V3/SP 1: MDS-A-SVJ 2: MDS-A-SPJ

(Continued on the next page.)

II - 229

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items

Details For MDS-B-SPJ2 (Continued from the previous page.)

Setting range

Standard setting

Select a value from the following table according to the regenerative resistance being used.
Setting value 0000 2000 2100 2200 2300 2400 2500 2600 2700 2800 2900 2A00 2B00 2C00 Regenerative resistance type Not connected FCUA-RB04 FCUA-RB075 FCUA-RB15 FCUA-RB22 FCUA-RB37 FCUA-RB55 FCUA-RB75/2 RUNIT1 RUNIT2 RUNIT3 RUNIT4 RUNIT5 Resistance value () 200 100 60 40 25 20 30/15 30 15 15 10 10 Capacity (W) 60 80 120 155 185 340 340/680 700 700 2100 2100 3100

(Note 1) This setting is used when using one FCUA-RB75/2 and when using two in parallel. 3242 SP042 CRNG C-axis detector This parameter is used to set the C-axis (PR) range detector range. Set "0" for this parameter. 3243 SP043 TRNG (PR) Synchronous tapping, spindle synchronous detector range This parameter is used to set the synchronous tapping or spindle synchronous detector range. Set "0" for this parameter. 0 to 7 0

0 to 7

3244 SP044 TRANS NC communi(PR) cation frequency 3245 SP045 CSNT Dual cushion timer

Set a frequency of data communication with 0 to 32767 Standard: NC. 0 Special: 1028 Set the cycle to add the increment values in 0 to 1000 the dual cushion process. (ms) When this setting value is increased, the dual cushion will increase, and the changes in the speed during acceleration/deceleration will become gradual. 0 to 1000 0

3246 SP046 CSN2 (PR)

Speed For an acceleration/deceleration time command dual constant defined in SP019 (CSN1) , this cushion parameter is used to provide smooth movement only at the start of acceleration/deceleration. As the value of this parameter is smaller, it moves smoother but the acceleration/deceleration time becomes longer. To make this parameter invalid, set "0". Speed Set the reset hysteresis width for a speed detection reset detection set value defined in SP020 value (SDTS). Speed reach range

3247 SP047 SDTR (PR) 3248 SP048 SUT (PR)

0 to 1000 (r/min)

30

Set the speed deviation rate with respect to 0 to 100 the commanded speed for output of the (%) speed reach signal.

15

II - 230

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3249 3250 3251 3252 3253 3254 3255 (PR)

Items SP049 TLM2 SP050 SP051 SP052 SP053 SP054 SP055 Torque limit 2

Details

Setting range 1 to 120 (%) 1 to 120 (%) 1 to 120 (%) 1 to 120 (%) 1 to 120 (%) 1 to 120 (%) 0 to 60 (s)

Standard setting 20 30 40 50 60 70 12

3256

SP056

3257 (PR) 3258 (PR)

SP057 SP058

3259 (PR)

SP059

3260 (PR)

SP060

3261 (PR)

SP061

3262 3263 (PR) 3264 (PR) 3265 (PR)

SP062 SP063 SP064 SP065

Set the torque limit rate for the torque limit signal 010. TLM3 Torque limit 3 Set the torque limit rate for the torque limit signal 011. TLM4 Torque limit 4 Set the torque limit rate for the torque limit signal 100. TLM5 Torque limit 5 Set the torque limit rate for the torque limit signal 101. TLM6 Torque limit 6 Set the torque limit rate for the torque limit signal 110. TLM7 Torque limit 7 Set the torque limit rate for the torque limit signal 111. SETM Excessive speed Set the timer value until the excessive deviation timer speed deviation alarm is output. The value of this parameter should be longer than the acceleration/deceleration time. PYVR Variable Set the minimum value of the variable excitation excitation rate. (min value) Select a smaller value when gear noise is too high. However, a larger value is effective for impact response. STOD Fixed control Set by Mitsubishi. constant Set "0" unless designated in particular. Set the speed for turning the 2nd speed SDT2 2nd speed detection speed detection ON. (This is valid only when SP038: SFNC6-bit8 is set to "1".) If the speed drops below this set speed, the 2nd speed detection will turn ON. When the speed reaches this set speed +15r/min or more, the 2nd speed detection will turn OFF. Set the base shut-off time for contactor MKT Winding switching at winding changeover. changeover Note that the contactor may damaged with base shut-off burning if the value of this parameter is too timer small. MKT2 Current limit Set the current limit time to be taken after timer after completion of contactor switching at winding winding changeover. changeover MKIL Current limit Set the current limit value for operation value after during a period defined in SP060 (MKT2) winding after completion of contactor switching at changeover winding changeover. Not used. Set to "0". OLT Overload alarm Set the time constant for detection of the detection time motor overload alarm. OLL Overload alarm Set the detection level of the motor detection level overload alarm. VCGN1 Target value of Set the magnification of speed loop variable speed proportional gain with respect to SP022 loop proportional (VGNP1) at the maximum motor speed gain defined in SP017 (TSP). II - 231

0 to 100 (%)

50

0 0 to 32767 (r/min)

0 0

50 to 10000 (ms)

150

0 to 10000 (ms) 0 to 120 (%)

500

75

0 0 to 1000 (s) 0 to 120 (%) 0 to 100 (%)

0 60 110 100

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items

Details

Setting range

Standard setting 0

3266 SP066 VCSN1 (PR)

Change starting Set the speed for starting change of speed 0 to speed of variable loop proportional gain. 32767 speed loop (r/min) proportional gain Proportional gain
SP022 SP022 (SP065/100) SP066 SP017

Speed

3267 SP067 VIGWA (PR) 3268 SP068 VIGWB (PR) 3269 SP069 VIGN (PR)

Change starting Set the speed for starting change of current 0 to speed of variable loop gain. 32767 current loop gain (r/min) Change ending Set the speed for ending change of current 0 to speed of variable loop gain. 32767 current loop gain (r/min) Target value of variable current loop gain Set the magnification of current loop gain (torque component and excitation component) for a change ending speed defined in SP068 (VIGWB). When this parameter is set to "0", the magnification is 1.
Gain SP069(1/16)-fold

0 to 32767 (1/16 -fold)

1-fold Speed SP067 SP068 SP017

SP017 (TSP) Maximum motor speed 0 to 6000 6001 to 8000 8001 or more

SP067 (VIGWA) 0 5000 5000

SP068 (VIGWB) 0 8000 10000

SP069 (VIGN) 0 45 64

3270 SP070 FHz

Machine resonance suppression filter frequency

When machine vibration occurs in speed and position control, set the frequency of the required vibration suppression. Note that a value of 100Hz or more is set. Set to "0" when not used. Set by Mitsubishi. Set "0" unless designated in particular.

0 to 3000 0 (Hz)

3271 (PR) 3272 (PR) 3273 (PR) 3274 (PR) 3275

SP071 VR2WA Fixed control constant SP072 VR2WB SP073 VR2GN SP074 IGDEC SP075 R2KWS

II - 232

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3276

Items SP076 FONS Machine resonance suppression filter operation speed

Details

Setting range

Standard setting 0

When the vibration increases in motor 0 to 32767 stop (ex. in orientation stop) when the (r/min) machine vibration suppression filter is operated by SP070, operate the machine vibration suppression filter at a speed of this parameter or more. When set to "0", this is validated for all speeds. Set by Mitsubishi. 0 Set "0" unless designated in particular.

3277 3278 (PR) 3279 (PR) 3280 3281 3282 3283 to 3286 3287 (PR)

SP077 TDSL SP078 FPWM SP079 ILMT SP080 SP081 LMCA SP082 LMCB SP083 to SP086 SP087 DIQM

Fixed control constant

Not used. Set to "0".

Target value of variable torque limit magnification at deceleration Speed for starting change of variable torque limit magnification at deceleration

Set the minimum value of variable torque limit at deceleration.

0 to 150 (%) 75

3288 (PR)

SP088 DIQN

Set the speed for starting change of torque limit value at deceleration.
Torque limit Inversely proportional to speed

0 to 32767 (r/min)

3000

100% SP087

Speed SP088 SP017

3289 3290 3291

SP089 SP090 SP091 OFSN Motor PLG forward rotation offset compensation Motor PLG reverse rotation offset compensation Fixed control constant

Not used. Set to "0". Not used. Set to "0". Set the PLG offset value for the forward rotation. Normally set to "0".

0 0 2048 to 2047 (1mv)

0 0 0

3292

SP092 OFSI

Set the PLG offset value for the reverse rotation. Normally set to "0".

2048 to 2047 (1mv)

3293 (PR)

SP093 ORE

Set by Mitsubishi. 0 Set "0" unless designated in particular.

II - 233

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items Load meter output filter

Details

Setting range

Standard setting 0

3294 SP094 LMAV (PR)

Set the filter time constant of load meter 0 to output. 32767 When "0" is set, a filter time constant is set to (2ms) 100ms. Set by Mitsubishi. Set "0" unless designated in particular. Set the gear ratio between the spindle end and the encoder end (except for the motor-built-in encoder) as indicated below.
Setting value 0 1 2 3 4 Gear ratio (deceleration) 1:1 1 : 1/2 1 : 1/4 1 : 1/8 1 : 1/16 Setting value 1 2 3 Gear ratio (Acceleration) 1:2 1:4 1:3

3295 SP095 VFAV (PR) 3296 SP096 EGAR (PR)

Fixed control constant Encoder gear ratio

3 to 4

3297 SP097 SPECO (PR)

Orientation specification

For MDS-B-SPJ2 Set the orientation specifications in bit units.

F E D C B A 9 8 tlet

0000 to FFFF HEX setting

0000

5 fdir

3 2 1 0 pyfx dmin odi2 odi1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 odi1 Orientation rotation direction odi2 00: Previous (the direction in which the motor has so far rotated under speed control) 01: Forward rotation 1 10: Backward rotation 11: Prohibited (Same as setting value = 10) Dummy in-position valid 2 dmin Dummy in-position invalid pyfx Excitation min. (50%) Excitation min. (50%) 3 during orientation servo during orientation servo lock invalid lock valid 4 fdir Encoder detector Encoder detector 5 polarity: + polarity: 6 7 8 tlet Turret indexing invalid Turret indexing valid 9 A B C D E F

(Continued on the next page.)

II - 234

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items For others

Details (Continued from the previous page.)

D C ksft gchg 5 fdir B A ips2 9 zdir 8

Setting range

Standard setting

Set the orientation specifications in bit units.

F E ostp orze 7 6 vg8x mdir

4 3 2 1 0 osc1 pyfx dmin odi2 odi1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 odi1 Orientation rotation direction odi2 00: Previous (the direction in which the motor has so far rotated under speed control) 01: Forward rotation 1 10: Backward rotation 11: Prohibited (Same as setting value = 10) Orientation in-position 2 dmin Orientation in-position advance invalid advance valid pyfx Excitation min. (50%) Excitation min. (50%) 3 during orientation servo during orientation servo lock invalid lock valid 4 osc1 Fixed control bit fdir Encoder detector Encoder detector 5 polarity: + polarity: 6 mdir Fixed control bit 7 vg8x 8 9 zdir Fixed control bit A ips2 2nd in-position invalid 2nd in-position valid B C gchg Fixed control bit D ksft E orze F ostp
In-position advance (bit 2) 0 (invalid) 0 (Invalid) Second position In-position signal in OINP width=1 Control output 4/ bit 4=1 Second in-position signal=0 Control output 4/ bit F=1 1 (valid) In-position signal in OINP width=1 Control output 4/ bit 4=1 Second in-position signal=0 Control output 4/ bit F=0 In-position signal in OINP width=1 Control output 4/ bit 4=1 Second in-position signal=0 Control output 4/ bit F=0

1 (Valid)

3298 (PR)

SP098 VGOP Speed loop gain proportional term in orientation mode SP099 VGOI Orientation mode speed loop gain integral term

Set the speed loop proportional gain in 0 to 1000 orientation mode. (1/s) When the gain is increased, rigidity is improved in the orientation stop but vibration and sound become larger. Set the speed loop integral gain in orientation mode. 0 to 1000 (0.1 1/s)

63

3299 (PR)

60

3300 (PR)

SP100 VGOD Orientation mode speed loop gain delay advance term

Set the a loop gain delay advance gain in 0 to 1000 orientation mode. (0.1 1/s) When this parameter is set to "0", PI control is exercised.

15

II - 235

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items Orientation advance in-position width

Details When using the orientation in-position advance function, set the in-position width that is larger than the normal in-position width defined in SP004 (OINP). Set the excessive error width in orientation mode.

Setting range 1 to 2880 (1/16)

Standard setting 16

3301 SP101 DINP (PR)

3302 SP102 OODR Excessive (PR) error value in orientation mode 3303 SP103 FTM (PR) Index positioning completion OFF time timer Torque limit value for orientation servo locking

1 to 32767 32767 (1/4 pulse) (1 pulse= 0.088)

Set the time for forcedly turn OFF the index 1 to 10000 200 positioning completion signal (different from (ms) the orientation completion signal) after the leading edge of the indexing start signal. Set the torque limit value for orientation 1 to 120 in-position output. (%) If the external torque limit signal is input the torque limit value set by this parameter is made invalid. 1 to 1000 (%) 100

3304 SP104 TLOR (PR)

3305 SP105 IQG0 (PR)

Current loop Set the magnification for current loop gain gain magnifica- (torque component) at orientation tion 1 in completion. orientation mode Current loop Set the magnification for current loop gain gain magnifica- (excitation component) at orientation tion 2 in completion. orientation mode Deceleration rate 2 in orientation mode Deceleration rate 3 in orientation mode Deceleration rate 4 in orientation mode

100

3306 SP106 IDG0

1 to 1000 (%)

100

3307 SP107 CSP2

Set the deceleration rate in orientation mode 0 to 1000 corresponding to the gear 001. When this parameter is set to "0", same as SP006 (CSP). Set the deceleration rate in orientation mode 0 to 1000 corresponding to the gear 010. When this parameter is set to "0", same as SP006 (CSP). Set the deceleration rate in orientation mode 0 to 1000 corresponding to the gear 011. When this parameter is set to "0", same as SP006 (CSP).

3308 SP108 CSP3

3309 SP109 CSP4 (PR)

3310 SP110 WCML Turret index (PR) command magnification 3311 SP111 WDEL Turret index deceleration magnification 3312 SP112 WCLP Turret index clamp speed

The integer magnification (gear ratio 1 : N) 0 to 32767 0 for the index position command (0 to 359) is (fold) set. This parameter is used only by SPH/SPJ2. The magnification for the orientation deceleration rate is set using 256 as 1. This parameter is used only by SPH/SPJ2. 0 to 32767 0 (1/256 -fold)

The max. speed during indexing is set. This 0 to 32767 0 becomes the max. speed of the motor when (r/min) set to "0". This parameter is used only by SPH/SPJ2.

II - 236

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items Turret index in-position width

Details

Setting range

Standard setting 0

3313 SP113 WINP (PR)

The position error range is set in which an 0 to 32767 orientation (indexing) completed signal is (1/16) output during turret indexing. This becomes the same as SP004 (OINP) when set to "0". An alarm "5C" will occur if the pulse miss 0 to 32767 value in the orientation stop exceed this (360/4096) setting value. (Note that this is invalid when set to "0".) In this parameter, set the value to fulfill the following conditions. SP114 setting value > 1.5 SP004 (orientation in-position width) When the door interlock spindle speed 0 to 32767 clamp signal is ON, this setting is used (r/min) instead of OSP(SP005), CZRN(SP149) and TZRN(SP214). (Note that SP149 and SP214 are used only for the M65V.) Set by Mitsubishi. Set "0" unless designated in particular. 0

3314 SP114 OPER

Orientation pulse miss check value

3315 SP115 OSP2

Orientation changeover speed limit value 2

3316 SP116 to to 3317 SP117 3318 SP118 ORCT Number of orientation retry times

Set the number of times to retry when an orientation or feedback error occurs. The warning (A9) is issued while retrying orientation, and an alarm (5C) is issued when the set number of times is exceeded.

0 to 100 (time)

3319 SP119 MPGH

Orientation position gain H winding compensation magnification

Set the compensation magnification of the 0 to 2560 orientation position loop gain for the H (1/256-fold) winding. H winding orientation position loop gain = SP001 (or SP002) SP119/256 When set to "0", will become the same as SP001 or SP002.

3320 SP120 MPGL

Orientation position gain L winding compensation magnification

Set the compensation magnification of the 0 to 2560 orientation position loop gain for the L (1/256-fold) winding. L winding orientation position loop gain = SP001 (or SP002) SP120/256 When set to "0", will become the same as SP001 or SP002.

3321 SP121 MPCSH Orientation deceleration rate H winding compensation magnification

Set the compensation magnification of the 0 to 2560 orientation deceleration rate for the H (1/256-fold) winding. Orientation deceleration rate for the H winding = SP006 SP121/256 When set to "0", will become the same as SP006.

II - 237

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items

Details

Setting range 0

Standard setting

3322 SP122 MPCSL Orientation deceleration rate L winding compensation magnification

Set the compensation magnification of 0 to 2560 the orientation deceleration rate for (1/256-fold) the L winding. Orientation deceleration rate for the L winding = SP006 SP122/256 When set to "0", will become the same as SP006.

3323 SP123 MGD0

Magnetic This parameter is used for adjustment 1 to 10000 detector output of orientation operation of the peak value magnetic detector. Set the output peak value of the magnetic detector. If a gap between the detector and the magnetizing element is small, increase the value of this parameter. If it is large, decrease the value of this parameter.

Standard magnetizing element: 542 Small magnetizing element: 500

3324 SP124 MGD1

Magnetic detector linear zone width

This parameter is used for adjustment 1 to 10000 of orientation operation of the magnetic detector. Set the linear zone width of the magnetic detector. If the mounting radius of the magnetizing element is large, decrease the value of this parameter. If it is small, increase the value of this parameter.

Standard magnetizing element: 768 Small magnetizing element: 440

3325 SP125 MGD2

Magnetic This parameter is used for adjustment 1 to 10000 detector of orientation operation of the switching point magnetic detector. Set the distance dimension from the target stop point at switching from position feedback to magnetic detector output. In common practices, assign a value that is approx. 1/2 of the value defined in SP124. Not used. Set to "0". 0

Standard magnetizing element: 384 Small magnetizing element: 220

3326 SP126 to to 3328 SP128

II - 238

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3329 (PR)

Items SP129 SPECC C-axis specifications

Details Set the C-axis specifications in bit units.

F E D C B zrtn ptyp fb9x zrtd zrn2 7 vg8x 6 5 fdir 4 3 A 9 zdir 1 adin 8 ztyp 0 fclx

Setting range

Standard setting 0000

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 fclx Closed loop Semi-closed loop 0 (Gear 1 : 1 only) adin Interpolation A/D Interpolation A/D 1 compensation invalid compensation valid rtrn Position monitor during Position monitor during 2 ready OFF invalid ready OFF valid 3 phos 4 fdir Position detector Position detector 5 direction (positive) direction (negative) 6 vg8x Speed gain 1/8 during Speed gain 1/8 during 7 torque limit valid torque limit invalid ztyp Z-phase type: Normal Z-phase type: Start up 8 start up only zdir Z-phase rising polarity Z-phase rising polarity 9 (+) () A B zrn2 Fixed control bit C zrtd Fixed control bit fb9x Speed feedback Speed feedback D Standard (PLG) 90,000 pulse detector ptyp Position control switch Position control switch E type: After zero point type: After deceleration return stop zrtn Zero point return Zero point return F direction: CCW direction: CW

3330

SP130 PGC1

First position loop gain for cutting on C-axis Second position loop gain for cutting on C-axis

Set the position loop gain when the first gain is 1 to 100 selected for C axis cutting. (1/s)

15

3331

SP131 PGC2

Set the position loop gain when the second gain 1 to 100 is selected for C axis cutting. (1/s)

15

II - 239

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3332 SP132 PGC3

Items

Details

Setting range

Standard setting 15

Third position Set the position loop gain when the third 1 to 100 loop gain for gain is selected for C-axis cutting. (1/s) cutting on C-axis Stop position Set the position loop gain for stopping loop gain for when carrying out C-axis cutting. cutting on C-axis C-axis Set the speed loop proportional gain in non-cutting C-axis non-cutting mode. speed loop gain proportional item 1 to 100 (1/s) 0 to 5000 (1/s)

3333 SP133 PGC4

15

3334 SP134 VGCP0 (PR)

63

3335 SP135 VGCI0 (PR)

C-axis Set the speed loop integral gain in C-axis 0 to 5000 non-cutting non-cutting mode. (0.1 1/s) speed loop gain integral item C-axis non-cutting speed loop gain delay advance item Set the speed loop delay advance gain in 0 to 5000 C-axis non-cutting mode. (0.1 1/s) When this parameter is set to "0", PI control is exercised. 0 to 5000 (1/s)

60

3336 SP136 VGCD0 (PR)

15

3337 SP137 VGCP1 (PR)

First speed loop Set the speed loop proportional gain gain proportional when the first gain is selected for C-axis item for C-axis cutting. cutting

63

3338 SP138 VGCI1 (PR)

First speed loop Set the speed loop integral gain when the 0 to 5000 gain integral first gain is selected for C-axis cutting. (0.1 1/s) item for cutting on C-axis First speed loop gain delay advance item for cutting on C-axis Set the speed loop delay advance gain when the first gain is selected for curing on the C-axis. When this parameter is set to "0", PI control is exercised. 0 to 5000 (0.1 1/s)

60

3339 SP139 VGCD1 (PR)

15

3340 SP140 VGCP2 (PR)

Second speed Set the speed loop proportional gain loop gain when the second gain is selected for proportional item C-axis cutting. for cutting on C-axis

0 to 5000 (1/s)

63

3341 SP141 VGCI2 (PR)

Second speed Set the speed loop integral gain when the 0 to 5000 loop gain second gain is selected for C-axis (0.1 1/s) integral item for cutting. cutting on C-axis

60

II - 240

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3342 (PR)

Items SP142 VGCD2 Second speed loop gain delay advance item for cutting on C-axis

Details

Setting range

Standard setting 15

Set the speed loop delay advance gain 0 to 5000 when the second gain is selected for (0.1 1/s) C-axis cutting. When this parameter is set to "0", PI control is exercised. 0 to 5000 (1/s)

3343 (PR)

SP143 VGCP3 Third speed loop Set the speed loop proportional gain gain proportional when the third gain is selected for item for cutting C-axis cutting. on C-axis SP144 VGCI3

63

3344 (PR)

Third speed loop Set the speed loop integral gain when 0 to 5000 60 gain integral item the third gain is selected for C-axis (0.1 1/s) for cutting on cutting. C-axis Set the speed loop delay advance gain 0 to 5000 15 when the third gain is selected for (0.1 1/s) C-axis cutting. When this parameter is set to "0", PI control is exercised. 0 to 5000 (1/s) 63

3345 (PR)

SP145 VGCD3 Third speed loop gain delay advance item for cutting on C-axis

3346 (PR)

SP146 VGCP4 Speed loop gain Set the speed loop proportional gain proporwhen C-axis cutting is stopped. tional item for stop of cutting on C-axis SP147 VGCI4

3347 (PR)

Speed loop gain Set the speed loop integral gain when 0 to 5000 integral item for C-axis cutting is stopped. (0.1 1/s) stop of cutting on C-axis

60

3348 (PR)

SP148 VGCD4 Speed loop gain delay advance item for stop of cutting on C-axis SP149 CZRN

Set the speed loop delay advance gain 0 to 5000 15 when C-axis cutting is stopped. (0.1 1/s) When this parameter is set to "0", PI control is exercised. 1 to 500 (r/min) 50

3349

C-axis zero point This parameter is valid when SP129 return speed (SPECC) bitE is set to "0". Set the zero point return speed used when the speed loop changes to the position loop. C-axis zero point return deceleration point

3350

SP150 CPDT

This parameter is valid when SP129 1 to 10000 (SPECC) bitE is set to "0". Set the deceleration rate where the machine starts to decelerate when it returns to the target stop point during C-axis zero point return. When the machine tends to overshoot at the stop point, set the smaller value.

3351

SP151 CPSTL C-axis zero point This parameter is valid when SPECC return shift (SP129) bitE is set to "0". amount Set the C-axis zero point position. (low byte)

HEX setting H: 0000 00000000 to L: 0000 FFFFFFFF (1/1000)

II - 241

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3352

Items SP152 CPSTH C-axis zero point return shift amount (high byte)

Details

Setting range

Standard setting

3353

SP153 CINP

C-axis Set the position error range in which in-position width the in-position signal is output on the C-axis. Excessive error Set the excessive error width on the width on C-axis C-axis. (low byte)

0000 to FFFF 03E8 (1/1000) HEX setting HEX setting 00000000 to FFFFFFFF (1/1000) H: 0001 L: D4C0

3354 (PR) 3355 (PR) 3356 to 3358 3359

SP154 CODRL

SP155 CODRH Excessive error width on C-axis (high byte) SP156 to SP158 SP159 CPY0 C-axis non-cutting variable excitation ratio C-axis cutting variable excitation ratio Current loop gain magnification 1 for non-cutting on C-axis Current loop gain magnification 2 for non-cutting on C-axis Current loop gain magnification 1 for cutting on C-axis Current loop gain magnification 2 for cutting on C-axis C-axis position loop gain 2 Not used. Set to "0".

Set the minimum value of variable excitation ratio for non-cutting on the C-axis . Set the minimum variable excitation ratio for cutting mode on the C-axis. Set the magnification of current loop gain (torque component) for C-axis non-cutting.

0 to 100 (%)

50

3360

SP160 CPY1

0 to 100 (%)

100

3361 (PR)

SP161 IQGC0

1 to 1000 (%)

100

3362 (PR)

SP162 IDGC0

Set the magnification of current loop 1 to 1000 gain (excitation component) for C-axis (%) non-cutting.

100

3363 (PR)

SP163 IQGC1

Set the magnification of current loop gain (torque component) for C-axis cutting.

1 to 1000 (%)

100

3364 (PR)

SP164 IDGC1

Set the magnification of current loop 1 to 1000 gain (excitation component) for C-axis (%) cutting.

100

3365

SP165 PG2C

Set the second position loop gain 0 to 999 when high-gain control is carried out (1/s) for control of the C-axis. This parameter is applied to all the operation modes of C-axis control. When this function is not used, assign "0".

II - 242

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3366

Items SP166 PG3C

Details

Setting range

Standard setting 0

C-axis position Set the third position loop gain when 0 to 999 loop gain 3 high-gain control is carried out for control (1/s) of the C-axis. This parameter is applied to all the operation modes of C-axis control. When this function is not used, assign "0". Position loop Set the position loop gain for when the gain for disturbance observer is valid. increased spindle holding force 0 to 100 (1/s)

3367 (PR)

SP167 PGU

15

3368 (PR)

SP168 VPUG

Speed loop Set the speed loop gain proportional item 0 to 5000 gain for when the disturbance observer is (1/s) proportional valid. item for increased spindle holding force Speed loop Set the speed loop gain integral item for gain integral when the disturbance observer is valid. item for increased spindle holding force 0 to 5000 (0.1 1/s)

63

3369 (PR)

SP169 VGUI

60

3370 (PR)

SP170 VGUD

Speed loop Set the speed loop gain delay advance 0 to 5000 gain delay item for when the disturbance observer is (0.1 1/s) advance item valid. for increased spindle holding force Not used. Set to "0". 0

15

3371 to 3376

SP171 to SP176

II - 243

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items

Details

Setting range 0000 to FFFF HEX setting

Standard setting 0000

3377 SP177 SPECS Spindle For MDS-B-SPJ2 (PR) synchronous Set the spindle synchronous specifications in specificabit units. tions
F E D odx8 5 fdir C B A 9 8

3 pyfx

0 fclx

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 fclx Closed loop Semi-closed loop 1 2 pyfx Normal excitation Position loop excitation 3 fixed (strong) 4 fdir Position detector Position detector 5 polarity (+) polarity () 6 7 8 9 A B C odx8 Magnification of Magnification of D excessive error width excessive error width 8 times invalid 8 times valid E F

For others Set the spindle synchronous specifications in bit units.

F E D odx8 5 fdir C B A 9 8

3 pyfx

1 adin

0 fclx

bit Name Meaning when set to 0 0 fclx Closed loop adin Interpolation A/D 1 compensation invalid 2 pyfx Normal excitation 3 4 5 6 7 8 9 A B C odx8 D E F Magnification of excessive error width 8 times invalid (Used with SPJ) fdir Position detector polarity (+)

Meaning when set to 1 Semi-closed loop Interpolation A/D compensation valid Position loop excitation fixed (strong) Position detector polarity ()

Magnification of excessive error width 8 times valid

II - 244

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3378 (PR) SP178 VGSP

Items Spindle synchronous speed loop gain proportional term Spindle synchronous speed loop gain integral term

Details

Setting range

Standard setting 63

Set the speed loop proportional gain in 0 to 1000 spindle synchronization mode. (1/s)

3379 (PR)

SP179 VGSI

Set the speed loop integral gain in spindle synchronization mode.

0 to 1000 (0.1 1/s)

60

3380 (PR)

SP180 VGSD Spindle synchronous speed loop gain delay advance term SP181 VCGS Target value of variable speed loop proportional gain at spindle synchroniza-tion SP182 VCSS Change starting speed of variable speed loop proportional gain at spindle synchroniza-tion

Set the speed loop delay advance gain 0 to 1000 in spindle synchronization mode. (0.1 1/s) When this parameter is set to "0", PI control is exercised. Set the magnification of speed loop 0 to 100 (%) proportional gain with respect to SP178 (VGSP) at the maximum speed defined in SP017 (TSP) at spindle synchronization. Set the speed for starting change of 0 to 32767 speed loop proportional gain at spindle (r/min) synchronization.
Proportional gain SP178 SP178 (SP181/100) SP182 SP017

15

3381 (PR)

100

3382 (PR)

Speed

3383

SP183 SYNV

Sync matching speed at spindle synchronization Acceleration rate feed forward gain at spindle synchronization Spindle sync in-position width

For changeover from the speed loop to 0 to 1000 the position loop at spindle (r/min) synchronization, set a speed command error range for output of the sync speed matching signal. Set the acceleration rate feed forward 0 to 1000 gain at spindle synchronization. (%) This parameter is used only with the SPJ2. Set the position error range for output 1 to 2880 of the in-position signal at spindle (1/16) synchronization. Set the excessive error width at spindle synchronization. 1 to 32767 (1/4 pulse) (1 pulse =0.088) 1 to 1000 (%)

20

3384 (PR)

SP184 FFCS

3385

SP185 SINP

16

3386 (PR)

SP186 SODR Excessive error width at spindle synchronization SP187 IQGS

32767

3387 (PR)

Current loop gain Set the magnification of current loop magnifigain (torque component) at spindle cation1 at spindle synchronization. synchronization

100

II - 245

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items Current loop gain magnification 2 at spindle synchronization Position loop gain 2 at spindle synchronization Position loop gain 3 at spindle synchronization

Details Set the magnification of current loop gain (excitation component) at spindle synchronization.

Setting range

Standard setting

3388 SP188 IDGS (PR)

1 to 1000 100 (%)

3389 SP189 PG2S

Set the second position loop gain when high-gain control is carried out at spindle synchronization. When this parameter function is not used, assign "0".

0 to 999 (1/s)

3390 SP190 PG3S

Set the third position loop gain when high-gain 0 to 999 control is carried out at spindle (1/s) synchronization. When this parameter function is not used, assign "0". Not used. Set to "0". 0

3391 SP191 to to 3392 SP192 3393 SP193 SPECT Synchronous (PR) tapping specifications

For MDS-B-SPJ2

0000 to Set the synchronous tapping specifications in FFFF HEX bit units. setting
F E D zrtn ptyp od8x 7 6 5 fdir C B A 9 8

0000

4 cdir

3 pyfx

0 fclx

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 fclx Closed loop Semi-closed loop 1 2 pyfx Normal excitation Position loop excitation 3 fixed (strong) 4 cdir Command polarity (+) Command polarity () fdir Position detector Position detector 5 polarity (+) polarity () 6 7 8 9 A B C od8x Magnification of Magnification of D excessive error width excessive error width 8 times invalid 8 times valid ptyp Position control switch Position control switch E type: After zero point type: After deceleration return stop zrtn Zero point return Zero point return F direction: CCW direction: CW

(Continued on the next page.)

II - 246

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items For others

Details (Continued from the previous page.)

Setting range

Standard setting

Set the synchronous tapping specifications in bit units.

F E D zrtn ptyp od8x 7 6 5 fdir C B A 9 8 phos 0 fclx

4 cdir

3 pyfx

2 rtrn

1 adin

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 fclx Closed loop Semi-closed loop 0 (Gear 1 : 1 only) adin Interpolation A/D Interpolation A/D 1 compensation invalid compensation valid rtrn Position monitor during Position monitor during 2 ready OFF invalid ready OFF valid pyfx Normal excitation Position loop excitation 3 fixed (strong) 4 cdir Command polarity (+) Command polarity () fdir Position detector Position detector 5 polarity (+) polarity () 6 7 phos Normal Synchronous tap 8 (no compensation) position compensation valid 9 A B C od8x Magnification of Magnification of D excessive error width excessive error width 8 times invalid 8 times valid ptyp Position control switch Position control switch E type: After zero point type: After deceleration return stop zrtn Zero point return Zero point return F direction: CCW direction: CW

3394 SP194 VGTP Synchronous Set the speed loop proportional gain in (PR) tapping speed synchronous tapping mode. loop gain proportional term 3395 SP195 VGTI (PR) Synchronous Set the speed loop integral gain in tapping speed synchronous tapping mode. loop gain integral term

0 to 1000 63 (1/s)

0 to1000 60 (0.1 1/s)

3396 SP196 VGTD Synchronous (PR) tapping speed loop gain delay advance term 3397 SP197 3398 SP198 VCGT Target value of (PR) variable speed loop proportional gain at synchronous tapping

Set the speed loop delay advance gain in 0 to1000 15 synchronous tapping mode. (0.1 1/s) When this parameter is set to "0", PI control is exercised. Not used. Set to "0". Set the magnification of speed loop proportional gain with respect to SP194 (VGTP) at the maximum motor speed defined in SP017 (TSP) at synchronous tapping. 0 0 to 100 (%) 0 100

II - 247

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No.

Items

Details

Setting range 0 to 32767 (r/min)

Standard setting 0

3399 SP199 VCST Change starting Set the speed for starting change of speed (PR) speed of loop proportional gain at synchronous variable speed tapping. loop proportional Proportional gain gain at SP194 synchronous tapping
SP194 (SP198/100) Speed SP199 SP017

Set the acceleration feed-forward gain for 0 to 1000 0 3400 SP200 FFC1 Synchronous tapping selection of gear 000 at synchronous tapping. (%) (PR) acceleration feed This parameter should be used when an error forward gain of relative position to Z-axis servo is large. (gear 1) Set the acceleration feed-forward gain for 0 to 1000 0 3401 SP201 FFC2 Synchronous tapping selection of gear 001 at synchronous tapping. (%) (PR) acceleration feed forward gain (gear 2) Set the acceleration feed-forward gain for 0 to 1000 0 3402 SP202 FFC3 Synchronous tapping selection of gear 010 at synchronous tapping. (%) (PR) acceleration feed forward gain (gear 3) Set the acceleration feed-forward gain for 0 to 1000 0 3403 SP203 FFC4 Synchronous tapping selection of gear 011 at synchronous tapping. (%) (PR) acceleration feed forward gain (gear 4) 3404 SP204 to to 3413 SP213 3414 SP214 TZRN Synchronous tapping zero point return speed 3415 SP215 TPDT Synchronous tapping zero point return deceleration rate Not used. Set to "0". 0 0

This parameter is valid when SP193 (SPECT) 0 to 500 bitE is set to "0". (r/min) Set the zero point return speed used when the speed loop changes to the position loop. This parameter is valid when SP193 (SPECT) 1 to bitE is set to "0". 10000 Set the deceleration rate where the machine starts to decelerate when it returns to the (pulse) target stop point during synchronous tapping zero point return. When the machine tends to overshoot at the stop point set a smaller value.

50

3416 SP216 TPST Synchronous tapping zero point return shift amount 3417 SP217 TINP Synchronous tapping in-position width

This parameter is valid when SP193 (SPECT) 0 to 4095 0 bitE is set to "0". Set the synchronous tapping zero point position. 1 to 2880 16 Set the position error range in which (1/16) in-position signal is output during synchronize tapping.

II - 248

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3418 (PR)

Items SP218 TODR Excessive error width at synchronous tapping Current loop gain magnification 1 at synchronous tapping Current loop gain magnification 2 at synchronous tapping Position loop gain 2 at synchronous tapping Position loop gain 3 at synchronous tapping

Details Set the excessive error width at synchronous tapping.

Setting range

Standard setting

1 to 32767 32767 (pulse) (1 pulse =0.088) 1 to 1000 (%) 100

3419 (PR)

SP219 IQGT

Set the magnification of current loop gain (torque component) during synchronous tapping.

3420 (PR)

SP220 IDGT

Set the magnification of current loop gain (excitation component) during synchronous tapping.

1 to 1000 (%)

100

3421

SP221 PG2T

Set the second position loop gain when 0 to 999 high-gain control is exercised during (1/s) synchronous tapping. When this parameter is not used, set to "0". Set the third position loop gain when 0 to 999 high-gain control is exercised during (1/s) synchronous tapping. When this parameter is not used, set to "0". Not used. Set to "0". 0

3422

SP222 PG3T

3423 to 0224 3425 3426 3427 3428 3429 3430 3431 3432 3433 (PR)

SP223 to SP224 SP225 OXKPH SP226 OXKPL SP227 OXVKP SP228 OXVKI SP229 OXSFT SP230 SP231 SP232 SP233 JL Fixed control constant

Set by Mitsubishi. Set "0" unless designated in particular.

Disturbance Set the ratio of the motor inertia + load observer inertia and motor inertia. general inertia scale Setting

0 to 5000 (%)

Motor inertia + load inertia value = Motor inertia 100

(Normally, set "100" or more. When less than "50" is set, the setting will be invalid.) 3434 (PR) SP234 OBS1 Disturbance observer low path filter frequency Set the frequency of the low path filter for when the disturbance observer is valid. Setting (1/s) = 2f f: Approx. 1.5 times the disturbance frequency Set the gain for the disturbance observer. 0 to 500 (%) 0 0 to 1000 (1/s) 0

3435 (PR)

SP235 OBS2

Disturbance observer gain

II - 249

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3436 SP236 to to 3452 SP252

Items

Details Not used. Set to "0". 0

Setting range

Standard setting 0

3453 SP253 DA1NO

D/A output channel 1 data number

Set the output data number for channel 1 of 32768 to the D/A output function. 32767 When the setting value is "0", the output is speedometer. Refer to "8.3 MDS-B-SP/SPH,SPJ2 SUPPLEMENTARY EXPLANATION". Set the output data number for channel 2 of 32768 to the D/A output function. 32767 When the setting value is "0", the output is load meter. Refer to "8.3 MDS-B-SP/SPH,SPJ2 SUPPLEMENTARY EXPLANATION". Set the data magnification for channel 1 of 32768 to the D/A output function. 32767 The output magnification is (setting (1/256-fold) value)/256. When set to "0", the output magnification becomes 1-fold, in the same manner as when "256" is set. Refer to "8.3 MDS-B-SP/SPH,SPJ2 SUPPLEMENTARY EXPLANATION". Set the data magnification for channel 2 of 32768 to the D/A output function. 32767 The output magnification is (setting (1/256-fold) value)/256. When set to "0", the output magnification becomes 1-fold, in the same manner as when "256" is set. Refer to "8.3 MDS-B-SP/SPH,SPJ2 SUPPLEMENTARY EXPLANATION". This parameter is valid only in the following 0000 to FFFF two conditional cases: HEX setting (a) In case that SP034 (SFNC2) bit0=1 and SP034 (SFNC2) bit2=0 Set the motor constants when using a special motor, not described in the SP040 (MTYP) explanation and when not using the coil changeover motor. (b) In case that SP034 (SFNC2) bit0=1 and SP034 (SFNC2) bit2=1 Set the motor constant of the H coil of the coil changeover motor. (Note) It is not allowed for the user to change the setting.

3454 SP254 DA2NO

D/A output channel 2 data number

3455 SP255 DA1MPY DA output channel 1 magnification

3456 SP256 DA2MPY DA output channel 2 magnification

3457 SP257 RPM (PR) to to SP320 BSD 3520 (PR)

Motor constant (H coil)

0000

II - 250

8. 8.2

MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS

No. 3521 (PR) to 3584 (PR)

Items SP321 RPML to SP384 BSDL Motor constant (L coil)

Details

Setting range

Standard setting 0000

This parameter is valid only in the following 0000 to conditional case: FFFF HEX setting (a) In case that SP034 (SFNC2) bit0=1 and SP034 (SFNC2) bit2=1 Set the motor constant of the L coil of the coil changeover motor. (Note) It is not allowed for the user to change the setting.

II - 251

8.3

8. MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SUPPLEMENTARY EXPLANATION(FOR D/A OUTPUT FUNCTIONS)

8.3 MDS-B-SP/SPH,SPJ2 SUPPLEMENTARY EXPLANATION (FOR D/A OUTPUT FUNCTIONS)

(1) Outline The D/A output function is mounted in the standard system in the MDS-A-SP/MDS-B-SP. Using this D/A output function, the drive unit status and each data can be confirmed. (2) Hardware specifications 2 channels 8 bit 0 to +10V Output pin CH 1: CN9-9 pin CH 2: CN9-19 pin GND: CN9-1.11 pin (3) Parameters Set the data No. and output magnification of each channel according to the parameters below. Name SP253 SP254 SP255 SP256 Details D/A channel 1 data No. D/A channel 2 data No. D/A channel 1 output magnification D/A channel 2 output magnification

(4) Output data No. Set the No. of the data to be output in SP253 and SP254. A correlation of the output data and the data No. is shown below. No. (setting value) 0 2 3 4 6 7 8 9 10 11 12 13 80 81 82 83 84 85 86 87 CH1 Output data Speedometer output Current command Current feedback Speed feedback Position droop low-order Position droop high-order Position F T low-order Position F T high-order Position command low-order Position command high-order Feedback position low-order Feedback position high-order Control input 1 Control input 2 Control input 3 Control input 4 Control output 1 Control output 2 Control output 3 Control output 4 Units Maximum speed at 10V When actual data=4096, 100% conversion When actual data=4096, 100% conversion Actual data r/min Interpolation units (when actual data = 23040000, 360 conversion) Interpolation units/NC communication cycle Output data Load meter output CH2 Units 120% load at 10V

Interpolation units (when actual data = 23040000, 360 conversion) Interpolation units (when actual data = 23040000, 360 conversion) Bit correspondence

Same as CH1

Bit correspondence

(Note) The % of the current command and current feedback indicate 30min. rating = 100%.

II - 252

8.3

8. MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SUPPLEMENTARY EXPLANATION(FOR D/A OUTPUT FUNCTIONS)

(5) Setting the output magnification Set the output magnification in SP255 and SP256. Data = actual data

SP255 or SP256 256

Using the expression above, (a) Output data other than speedometer output and load meter output carries out the D/A output in Fig. 1. (b) Speedometer output data and load meter output data carries out the D/A output in Fig. 2.

D/A output voltage

D/A output voltage

+10V

+10V

+5V

+5V

0V 128

+127

DATA

0V 0 +127 +255

DATA

Fig. 1

Fig. 2

(Example 1) Current command, current feedback Data units are 100% converted when the actual data = 4096. Therefore, for example, the actual data is output as shown below during +120% current feedback. Actual data = 4096 1.2 = 4915 If "256" is set (magnification 1) in parameter SP255 (SP256), the D/A output voltage from Fig. 1 will be as shown below, exceeding the D/A output voltage maximum value. 5V + {4915 1 (5V/128)} = 197V > 10V Therefore, if (for example) "6" is set in parameter SP255 (SP256), the D/A output voltage will become as shown below, and data confirmation will be possible. 5V + {4915 6/256 (5V/128)} = 9.5V < 10V

II - 253

8.3

8. MDS-B-SP/SPH,SPJ2 SPINDLE PARAMETERS MDS-B-SP/SPH,SPJ2 SUPPLEMENTARY EXPLANATION(FOR D/A OUTPUT FUNCTIONS) Speed feedback Data units are r/min. Therefore, at (for example) +2000r/min, the motor speed will be output as "2000". If "256" is set (magnification 1) in parameter SP255 (SP256), the D/A output voltage from Fig. 1 will be as shown below, exceeding the D/A output voltage maximum value. 5V + {2000 x 1 x (5V/128)} = 83.125V > 10V Therefore, if (for example) "16" is set in parameter SP255 (SP256), the D/A output voltage will become as shown below, and data confirmation will be possible. 5V + {2000 x 16/256 x (5V/128)} = 9.88V < 10V

(Example 2)

(Example 3) Position droop The data units are r/min. Data units are 100% converted when the actual data = 4096. Therefore, for example, the actual data is output as shown below during the +0.1 position droop. Actual data = 0.1 x 23040000/360 = 6400 If "256" is set (magnification 1) in parameter SP255 (SP256), the D/A output voltage from Fig. 1 will be as shown below, exceeding the D/A output voltage maximum value. 5V + {6400 x 1 x (5V/128)} = 255V > 10V Therefore, if (for example) "5" is set in parameter SP255 (SP256), the D/A output voltage will become as shown below, and data confirmation will be possible. 5V + {2000 x 5/256 x (5V/128)} = 9.88V < 10V (Example 4) Confirm the orientation complete signal (ORCF) in the control output 4L. The data units are bit corresponding data. Refer to the Instruction Manual for the meanings of the control output 4L bit corresponding signals. The orientation complete signal (ORCF) corresponds to the control output 4L/bit 4. Therefore, for example, the actual data is output as shown below when ORCF= ON. bit 4 corresponding actual data = 24 = 16 If "256" is set (magnification 1) in parameter SP255 (SP256), the D/A output voltage from Fig. 1 will be as shown below, and data confirmation will be possible. 5V + {16 x 1 x (5V/128)} = 5.625V < 10V Note that, if a bit other than bit4 is ON, the current of that bit will be added to the 6.25V shown above, and at the actual ORCF signal measurement will be as shown below, so confirm the changed voltage. (5.625 V 5V) = 0.625 V

II - 254

9.1

9. MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE BASE SPECIFICATIONS PARAMETERS

9.

MDS-C1-SP, SPM SPINDLE PARAMETERS

9.1 MDS-C1-SP SPINDLE BASE SPECIFICATIONS PARAMETERS

For parameters indicated with a (PR) in the table, turn the CNC power OFF after setting. The setting is validated after the power is turned ON again. Refer to Instruction Manual for each CNC and the following spindles. MELDAS AC Servo and Spindle MDS-C1 Series Specifications Manual .............. BNP-C3000 No. 3001 slimit 1 3002 3003 3004 2 3 4 Maximum Set maximum spindle speed with gears 00, 01, rotation speed 10, 11. Set the value that is equal to or larger than "slimit" value. By comparing the S command value of gear 1 to 4, a spindle gear shift command will be output automatically. Shift rotation speed Set spindle rotation speed for gear shifting with gears 00, 01, 10, 11. (Note) Setting too large value may cause a gear nicks when changing gears. Tap rotation speed Set maximum spindle rotation speed during tap cycle with gears 00, 01, 10, 11. 0 to 99999 (r/min) 0 to 32767 (r/min) Items Limit rotation speed Details Set spindle rotation speed for maximum motor rotation speed with gears 00, 01, 10, 11. (Set the spindle rotation speed for the S analog output 10V.) Setting range (Unit) 0 to 99999 (r/min)

3005 smax 1 3006 3007 3008 2 3 4

3009 ssift 3010 3011 3012

1 2 3 4

3013 stap 1 3014 3015 3016 2 3 4

3017 stapt 1 3018 3019 3020 2 3 4

Tap time constant

Set time constants for constant inclination synchronized tapping for gears 00, 01, 10, 11 (linear acceleration/deceleration pattern).

1 to 5000 (ms)

II - 255

9.1

9. MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE BASE SPECIFICATIONS PARAMETERS

Relationship between spindle limit rotation speed and maximum spindle rotation speed
Output voltage (V) 10V

Spindle rotation speed (r/min) 0 smax1 slimt1 smax2 slimt2 smax(n) slimt(n)

Limit rotation speed of gear 1 (Parameter setting) Maximum rotation speed of gear 1 (Parameter setting) Set "0" for any unused gears.

Relation between the spindle limit rotation speed and the spindle tap time constant (for the constant inclination synchronized tapping)
Spindle rotation speed (r/min) slimt(n) slimt(n) slimt2 slimt1 S command Spindle rotation speed (r/min)

Time (ms) 0 stapt1 stapt2 stapt(n) Execution time constant stapt(n)

Time (ms)

II - 256

9.1

9. MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE BASE SPECIFICATIONS PARAMETERS

# 3021 sori

Items Orientation rotation speed

Details Set the spindle orientation rotation speed. Set the rotation speed for when the spindle rotates at the constant rotation speed.

Setting range (Unit) 0 to 32767 (r/min)

3022 sgear

Encoder gear Set the gear ratio of the spindle to the encoder. ratio

0: 1/1 1: 1/2 2: 1/4 3: 1/8 0 to 32767 (r/min)

3023 smini

Minimum rotation speed Spindle connection

Set the minimum rotation speed of the spindle. If an S command instructs the rotation speed below this setting, the spindle rotates at the minimum rotation speed set with this parameter. Set the type of the spindle to be connected. 0: No connection with the spindle 1: Serial connection (bus) 2 to 5: Analog output Set connection information of the spindle encoder. 0: No connection 1: Spindle connection (Spindle encoder connection check function valid.) 2: Serial connection of encoder 0: Perform orientation using the winding selected when the orientation command is issued. 1: Use winding L whenever the orientation command is issued. 0: The winding H/L is selected by the actual spindle rotation speed (calculated from commanded rotation speed) when spindle synchronous control starts. (The winding is not switched during synchronous control. The control is carried out with the winding selected at start.) If the actual spindle rotation speed is less than SP020, the winding L is selected, and if more than the value, the winding H is selected. 1: Use winding H whenever the spindle synchronous command is issued.

3024 sout (PR)

0 to 5

3025 enc-on

Spindle encoder

0 to 2

3026

cs_ori

Selection of winding in orientation mode Selection of winding in spindle synchronou s mode

0/1

3027

cs_syn

0/1

3028

sprcmm

L system tap Set the M code of the spindle forward run/reverse 0 to 999999 cycle spindle run command. forward run/ High-order three digits : reverse run M The spindle forward run command's M code command is set. Low-order three digits : The spindle reverse run command's M code is set.

II - 257

9.1

9. MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE BASE SPECIFICATIONS PARAMETERS

# 3029 tapsel

Items Asynchronous tap gear selection

Details Specify whether to use the tap spindle rotation speed or maximum spindle rotation speed for the gear that is selected when an asynchronous tap command is issued. 0: Tap spindle rotation speed 1: Maximum spindle rotation speed This parameter is valid only when the M-function synchronous tap cycle enable parameter (#1272 ext08 bit1) is ON. Select whether to use magnetic bearings. 0: Magnetic bearings invalid 1: Magnetic bearings valid Using a 4-digit number, set the amplifier interface channel No. and which axis in that channel is to be used when connecting a spindle amplifier. High-order two digits : Amplifier interface channel No. Low-order two digits : Axis No. When using the conventional fixed layout, set all axes to "0000". Set "0000" when using an analog spindle. Using a 4-digit number, set the amplifier interface channel No. and which axis in that channel is to be used when connecting a magnetic bearing amplifier. High-order two digits : Amplifier interface channel No. Low-order two digits : Axis No. When using the conventional fixed layout, set all axes to "0000". Set the spindle rotation speed at which the step-2 acceleration/deceleration time constant is to be switched at gear 00, 01, 10, or 11.

Setting range (Unit) 0/1

3030 mbsel (PR) 3031 smcp_no (PR)

Selection of magnetic bearings Amplifier I/F channel No. (spindle)

0/1

0000 0101 to 0107 0201 to 0207

3032 mbmcp_no (PR)

Amplifier I/F channel No. (magnetic bearing)

0000 0101 to 0107 0201 to 0207

3037 tapt 21 3038 22 3039 23 3040 24 3041 tapt 21 3042 22 3043 23 3044 24 3045 tapt 31 3046 32 3047 33 3048 34 3049 spt

Synchronized 0 to 99999 tapping (r/min) Switching spindle rotation speed 2 Synchronized Set the time constant to reach Synchronized tapping 1 to 5000 (ms) tapping switching spindle rotation speed 2 (#3037 to #3040) at Switching time gear 00, 01, 10, or 11. constant 2 Synchronized Set the time constant to reach the maximum rotation 1 to 5000 (ms) tapping spindle speed (#3005 to #3008) at gear 00, 01, 10, or Switching time 11. constant 3 Spindle synchronization acceleration/ deceleration time constant Spindle synchronization rotation speed attainment level Set the acceleration/deceleration time constant for 0 to 9999 (ms) when the spindle synchronization command's rotation speed changes during spindle synchronous control.

3050 sprlv

The spindle rotation speed synchronization complete 0 to 4095 (pulse) signal will turn ON when the difference of the (1 pulse = reference spindle and synchronous spindle actual 0.088) rotation speeds is less than the level set for the synchronous spindle rotation speed command value during spindle synchronous control.

II - 258

9.1

9. MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE BASE SPECIFICATIONS PARAMETERS

# 3051 spplv

Items Spindle phase synchronization attainment level Spindle motor spindle relative polarity

Details

Setting range (Unit)

The spindle phase synchronization complete 0 to 4095 (pulse) signal will turn ON when the phase difference (1 pulse = 0.088) of the reference spindle and synchronous spindle is less than the set level during spindle phase synchronization control. Set the spindle motor and spindle's relative polarity. Spindle CW rotation at motor CW rotation : Positive polarity Spindle CCW rotation at motor CW rotation : Negative polarity 0: Positive polarity 1: Negative polarity

3052

spplr

3053

sppst

Spindle encoder Set the deviation amount from the spindle's Z -phase position reference position to the spindle encoder's Z phase. The deviation amount is obtained using the clockwise direction looking from the front of the spindle as the positive direction. Spindle synchronization multi-step acceleration/ deceleration changeover speed 1 Spindle synchronization multi-step acceleration/ deceleration changeover speed 2 Spindle synchronization multi-step acceleration/ deceleration changeover speed 3 Spindle synchronization multi-step acceleration/ deceleration changeover speed 4 Spindle synchronization multi-step acceleration/ deceleration changeover speed 5 Set the spindle speed for changing the 1st step's acceleration/deceleration time constant.

0 to 359999 (1/1000)

3054

sptc1

0 to 99999 (r/min)

3055

sptc2

Set the spindle speed for changing the 2nd step's acceleration/deceleration time constant.

0 to 99999 (r/min)

3056

sptc3

Set the spindle speed for changing the 3rd step's acceleration/deceleration time constant.

0 to 99999 (r/min)

3057

sptc4

Set the spindle speed for changing the 4th step's acceleration/deceleration time constant.

0 to 99999 (r/min)

3058

sptc5

Set the spindle speed for changing the 5th step's acceleration/deceleration time constant.

0 to 99999 (r/min)

II - 259

9.1

9. MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE BASE SPECIFICATIONS PARAMETERS

# 3059 sptc6

Items

Details

Setting range (Unit)

Spindle Set the spindle speed for changing the 6th step's 0 to 99999 (r/min) synchroniza- acceleration/deceleration time constant. tion multi-step acceleration/ deceleration changeover speed 6 Spindle Set the spindle speed for changing the 7th step's 0 to 99999 (r/min) synchroniza- acceleration/deceleration time constant. tion multi-step acceleration/ deceleration changeover speed 7 Magnification for time constant changeover speed 1 Set the acceleration/deceleration time constant between the spindle synchronization multi-step acceleration/deceleration changeover speed 1 (sptc1) to the spindle synchronization multi-step acceleration/ deceleration changeover speed 2 (sptc2) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt). Set the acceleration/deceleration time constant between the spindle synchronization multi-step acceleration/deceleration changeover speed 2 (sptc2) to the spindle synchronization multi-step acceleration/deceleration changeover speed 3 (sptc3) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt). Set the acceleration/deceleration time constant between the spindle synchronization multi-step acceleration/deceleration changeover speed 3 (sptc3) to the spindle synchronization multi-step acceleration/deceleration changeover speed 4 (sptc4) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt). Set the acceleration/deceleration time constant between the spindle synchronization multi-step acceleration/deceleration changeover speed 4 (sptc4) to the spindle synchronization multi-step acceleration/deceleration changeover speed 5 (sptc5) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt). 0 to 127

3060

sptc7

3061

spdiv1

3062

spdiv2

Magnification for time constant changeover speed 2

0 to 127

3063

spdiv3

Magnification for time constant changeover speed 3

0 to 127

3064

spdiv4

Magnification for time constant changeover speed 4

0 to 127

II - 260

9.1

9. MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE BASE SPECIFICATIONS PARAMETERS

# 3065 spdiv5

Items Magnification for time constant changeover speed 5

Details

Setting range (Unit)

Set the acceleration/deceleration time constant 0 to 127 between the spindle synchronization multi-step acceleration/deceleration changeover speed 5 (sptc5) to the spindle synchronization multi-step acceleration/deceleration changeover speed 6 (sptc6) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt). Set the acceleration/deceleration time constant 0 to 127 between the spindle synchronization multi-step acceleration/deceleration changeover speed 6 (sptc6) to the spindle synchronization multi-step acceleration/deceleration changeover speed 7 (sptc7) as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt). Set the acceleration/deceleration time constant 0 to 127 for the spindle synchronization multi-step acceleration/ deceleration changeover speed 7 (sptc7) and higher as a magnification in respect to the spindle synchronization acceleration/deceleration time constant (spt). Set the time to confirm that synchronization is attained before phase synchronization control is started. When "0" is set, the time will be 2 seconds. When "100" or less is set, the time will be 100ms. 0 to 9999 (ms)

3066

spdiv6

Magnification for time constant changeover speed 6

3067

spdiv7

Magnification for time constant changeover speed 7

3068

symtm1

Phase synchronization start confirmation time Phase synchronization end confirmation time Phase synchronization speed

3069

symtm2

Set the time to wait for phase synchronization 0 to 9999 (ms) control to end as the time for the rotation speed to reach the attainment range. When "0" is set, the time will be 2 seconds. When "100" or less is set, the time will be 100ms. Set the fluctuation amount to change the 0 to 100 (%) synchronous spindle rotation speed during phase synchronization control as the command speed and rate. When "0" is set, the amount will be 100%.

3070

syprt

3071 3072

(Not used.) (Not used.)

II - 261

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

9.2 MDS-C1-SP SPINDLE PARAMETERS

For parameters marked with a (PR) in the tables, turn the CNC power OFF after setting. The parameters will be valid after the power is turned ON again. The "fixed control constants" and "fixed control bits" in this section are set by Mitsubishi.

! CAUTION
! !

Do not make remarkable adjustments or changes of the parameters as the operation may become unstable. In the explanation on bits, set all bits not used, including blank bits, to 0. Setting range Standard setting 100

No.

Items Magnetic sensor and motor built-in encoder orientation position loop gain Encoder orientation position loop gain

Details

3201 SP001 PGM

As the set value is larger, the orientation time 0 to 1000 becomes shorter and servo rigidity is increased. (0.1 1/s) However, vibration is increased and the machine becomes likely to overshoot.

3202 SP002 PGE

As the set value is larger, the orientation time 0 to 1000 becomes shorter and servo rigidity is increased. (0.1 1/s) However, vibration is increased and the machine becomes likely to overshoot. Set the position loop gain in C-axis non-cutting 1 to 100 mode. (1/s) During non-cutting (rapid traverse, etc.) with the C axis control, this position loop gain setting is valid. Set the position error range in which an orientation completion signal is output. 1 to 2880 (1/16 )

100

3203 SP003 PGC0 C-axis non-cutting position loop gain 3204 SP004 OINP Orientation in-position width 3205 SP005 OSP (PR) Orientation mode changing speed limit value

15

16

Set the motor speed limit value to be used when 0 to 32767 the speed loop is changed to the position loop in (r/min) orientation mode. When this parameter is set to "0", SP017 (TSP) becomes the limit value. 1 to 1000

3206 SP006 CSP

Orientation As the set value is larger, the orientation time mode becomes shorter. However, the machine deceleration becomes likely to overshoot. rate

20

3207 SP007 OPST In-position Set the stop position for orientation. shift amount (i) Motor built-in encoder, encoder: for Set the value by dividing 360 by 4096. orientation (ii) Magnetic sensor: Divide 5 to +5 by 1024 and put 0 for 0. 3208 SP008 3209 SP009 PGT Not used. Set to "0". Synchroni- Set the spindle position loop gain in zed tapping synchronized tapping mode. Position loop gain

(i) 0 to 4095 0 (ii) 512 to512

0 1 to 100 (1/s)

0 15

II - 262

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items Spindle synchronous position loop gain

Details Set the spindle position loop gain in spindle synchronization mode.

Setting range 1 to 100 (1/s)

Standard setting 15

3210 SP010 PGS

3211 SP011 to to 3216 SP016 3217 SP017 TSP (PR) 3218 SP018 ZSP (PR) 3219 SP019 CSN1 (PR) 3220 SP020 SDTS (PR) Maximum motor speed

Use not possible.

Set the maximum motor speed of the spindle.

1 to 32767 (r/min) 1 to 1000 (r/min)

6000

Motor zero Set the motor speed for which zero-speed speed output is performed. Speed cushion 1 Speed detection set value Torque limit 1

50 30

Set the time constant for a speed command from 1 to 32767 "0" to the maximum speed. (10ms) (This parameter is invalid in position loop mode.) Set the motor speed so for which speed detection output is performed. Usually, the setting value is 10% of SP017 (TSP). Set the torque limit rate for torque limit signal 001. Set the speed loop proportional gain in speed control mode. When the gain is increased, response is improved but vibration and sound become larger. 0 to 32767 (r/min)

600

3221 SP021 TLM1

0 to 120 (%) 10 0 to 1000 (1/s) 63

3222 SP022 VGNP1 Speed (PR) loop gain proportional term under speed control 3223 SP023 VGNI1 Speed (PR) loop gain integral term under speed control 3224 SP024 3225 SP025 GRA1 (PR)

Set the speed loop integral gain in speed control 0 to 1000 mode. (0.1 1/s) Usually, set a value in proportion to SP022 (VGNP1).

60

Use not possible. Spindle Set the number of gear teeth of the spindle gear teeth corresponding to gear 000. count 1

0 1 to 32767

0 1

II - 263

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items Spindle gear teeth count 2 Spindle gear teeth count 3 Spindle gear teeth count 4 Motor shaft gear teeth count 1 Motor shaft gear teeth count 2 Motor shaft gear teeth count 3 Motor shaft gear teeth count 4

Details Set the number of gear teeth of the spindle corresponding to gear 001.

Setting range 1 to 32767

Standard setting 1

3226 SP026 GRA2 (PR)

3227 SP027 GRA3 (PR)

Set the number of gear teeth of the spindle corresponding to gear 010.

1 to 32767

3228 SP028 GRA4 (PR)

Set the number of gear teeth of the spindle corresponding to gear 011.

1 to 32767

3229 SP029 GRB1 (PR)

Set the number of gear teeth of the motor shaft corresponding to gear 000.

1 to 32767

3230 SP030 GRB2 (PR)

Set the number of gear teeth of the motor shaft corresponding to gear 001.

1 to 32767

3231 SP031 GRB3 (PR)

Set the number of gear teeth of the motor shaft corresponding to gear 010.

1 to 32767

3232 SP032 GRB4 (PR)

Set the number of gear teeth of the motor shaft corresponding to gear 011.

1 to 32767

II - 264

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details

Setting range
8 pycal pychg 1 0 dflt 1a2m

Standard setting

3233 SP033 SFNC1 Spindle Set the spindle function 1 in bit units. (PR) function 1 F E D C B A 9
poff hzs 5 ront 4 3 2 sftk

0000 to 0000 FFFF HEX setting

7 6 pyst pyoff

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 1 amplifier 0 1a2m 1 amplifier 2 motor function: Invalid 2 motor function: Valid 1 dflt Default motor: Main Default motor: Sub 2 sftk SF-TK card invalid SF-TK card valid 3 4 5 6 pyoff This is used by Mitsubishi. 7 pyst Set to "0" unless particularly designated. 8 9 A B C D E F hzs poff ront This is used by Mitsubishi. Set to "0" unless particularly designated. Normal ready ON High-speed ready ON This is used by Mitsubishi. Set to "0" unless particularly designated. Gate OFF by high-cycle Gate OFF by high-cycle zero speed invalid zero speed valid Contactor hold at NC Contactor hold at NC power OFF invalid power OFF valid pychg pycal (Conventional specifications) High-speed rate deceleration method valid for minimum excitation rate

(Note) When SPH is used, bit 0 and bit 1 will be invalid.

3234 SP034 SFNC2 Spindle Set the spindle function 2 in bit units. (PR) function 2 F E D C B A 9

0000 to 0000 FFFF HEX setting

3 2 1 0 mkc2 mkch invm mts1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 0 mts1 Special motor constant invalid 1 invm A general-purpose motor FV control invalid 2 mkch Winding switch function invalid mkc2 Coil changeover function 2 invalid 3 4 5 6 7 8 9 A B C D E F Meaning when set to 1 Special motor constant setting valid A general-purpose motor FV control valid Winding switch function valid Coil changeover function 2 valid (Turns ON simultaneously with bit 2)

(Note) bit3 mkc2 must be handled on the NC side.

II - 265

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details Set the spindle function 3 in bit units.

F E D C B A 9 8

Setting range 0000 to FFFF HEX setting

Standard setting 0000

3235 SP035 SFNC3 Spindle (PR) function 3

3 2 1 0 lbsd hbsd lwid hwid

Meaning when set to 1 H-coil wide-range constant output valid L-coil wide-range constant output valid H-coil base slide valid L-coil base slide valid

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 hwid H-coil wide-range 0 constant output invalid lwid L-coil wide-range 1 constant output invalid 2 hbsd H-coil base slide invalid 3 lbsd L-coil base slide invalid 4 5 6 7 8 (Used with SPJ.) 9 A B C D E F

3236 SP036 SFNC4 Spindle (PR) function 4

Set the spindle function 4 in bit units.

F E D C B A 9 8 dslm dssm

0000 to FFFF HEX setting

0000

5 4 3 2 1 0 enc2 enc1 mag2 mag1 plg2 plg1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 0 plg1 PLG of motor 1 valid 1 plg2 PLG of motor 2 valid 2 mag1 MAG of motor 1 valid 3 mag2 MAG of motor 2 valid 4 enc1 ENC of motor 1 valid 5 enc2 ENC of motor 2 valid 6 7 8 dssm Speedometer output valid 9 A B C D E F dslm Load meter output valid Meaning when set to 1 PLG of motor 1 invalid PLG of motor 2 invalid MAG of motor 1 invalid MAG of motor 2 invalid ENC of motor 1 invalid ENC of motor 2 invalid

Speedometer output invalid Load meter output invalid

II - 266

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details Set the spindle function 5 in bit units.

F E splg dplg 7 6 D C B A 9 8 noplg nsno nosg 2 1 0 plgo mago enco

Setting range 0000 to FFFF HEX setting

Standard setting 0000

3237 SP037 SFNC5 Spindle (PR) function 5

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 0 enco Encoder orientation invalid 1 mago Magnetic sensor orientation invalid 2 plgo PLG orientation invalid 3 4 5 6 7 nosg No-signal detection type 8 (Always monitoring) 9 A B C D E F No-signal detection valid Constant monitor of noplg PLG-Z phase no-signal invalid nsno Meaning when set to 1 Encoder orientation valid Magnetic sensor orientation valid PLG orientation valid

Monitoring only in position loop or orientation-mode No-signal detection invalid Constant monitor of PLG-Z phase no-signal valid

dplg splg

This is used by Mitsubishi. Set to "0" unless particularly designated.

(Note) For bit0 to 2, do not set two bits or more to "1" at the same time.

II - 267

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details Set the spindle function 6 in bit units.

F oplp E lmx D C B A 9 8 iqsv XFzs dcsn lmnp pl80 sdt2 4 tdn 3 2 plg2 pftm 1 0 alty

Setting range 0000 to FFFF HEX setting

Standard setting 0000

3238 SP038 SFNC6 Spindle (PR) function 6

7 6 5 vfbs orm adin

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 alty Deceleration stop during Deceleration stop during 0 special alarm invalid special alarm valid 1 pftm Encoder feedback serial Encoder feedback serial 2 communication invalid communication valid plg2 Semi-closed pulse Semi-closed pulse 3 output signal 2 invalid output signal 2 valid 4 adin Interpolation during Interpolation during 5 thread cutting invalid thread cutting valid orm Orientation start memo Orientation start memo 6 invalid valid vfbs This is used by Mitsubishi. 7 Set to "0" unless particularly designated. sdt2 (Follows SFNC6-bitC Set output 2 to 2nd 8 setting) speed detection output pl80 MHE90K detector's 180 180 wave PLG other 9 wave PLG than MHE90K A lmnp This is used by Mitsubishi. Set to "0" unless particularly designated. dcsn Dual cushion during Dual cushion during B acceleration/ acceleration/ deceleration valid deceleration invalid C XFzs Set output 2 to MP scale Set output 2 to zero low (L) speed mode speed output D iqsv This is used by Mitsubishi. E lmx Set to "0" unless particularly designated F oplp Open loop operation invalid Open loop operation valid

3239 SP039 ATYP (PR)

Amplifier type

Set the amplifier type. Set each amplifier type or "0"

Parameter setting 0000 0001 0002 0003 0004 0005 0006 0007 0008 0009 000A 000B 000C 000D 000E 000F 0010 SP-075 SP-15 SP-22 SP-37 SP-55 SP-75 SP-110 SP-150 SP-185 SP-220 SP-260 SP-300 SP (H)-370 SP (H)-450 SP-04 SP-550 Amplifier type

0000 to FFFF HEX setting

0000

II - 268

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details This parameter is valid when SP034 (SFNC2) bit0 is set to "0". Set the appropriate motor number from the standard motors listed below.
Parameter setting 0000 0001 0002 0003 0004 0005 0006 0007 0008 0009 000A 000B 000C 000D 000E 000F 0010 0011 0012 0013 0014 0015 0016 0017 0018 0019 001A 001B 001C 001D 001E 001F Motor type Maximum speed 10000 r/min 10000 r/min 8000 r/min 8000 r/min 6000 r/min 6000 r/min 6000 r/min 4500 r/min 4500 r/min 4500 r/min Corre-spo nding amplifier SP-22 SP-37 SP-55 SP-75 SP-110 SP-150 SP-185 SP-220 SP-260 SP-300

Setting range 0000 to FFFF HEX setting

Standard setting 0000

3240 SP040 MTYP Motor type (PR)

SJ-2.2A SJ-3.7A SJ-5.5A SJ-7.5A SJ-11A SJ-15A SJ-18.5A SJ-22A SJ-26A SJ-30A

SJ-N0.75A SJ-N1.5A SJ-N2.2A SJ-N3.7A SJ-N5.5A SJ-N7.5A

10000 r/min 10000 r/min 10000 r/min 10000 r/min 8000 r/min 8000 r/min

SP-075 SP-15 SP-22 SP-37 SP-55 SP-75

SJ-J2.2A SJ-J3.7A SJ-J5.5A SJ-J7.5A

10000 r/min 10000 r/min 8000 r/min 8000 r/min

SP-22 SP-37 SP-55 SP-75

II - 269

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details Power Power supply type F E D C supply type

amp 7 6 5 4 ptyp
bit 0 1 2 3 4 5 6 7 8 9 A B C D E F

Setting range
A rtyp 9 8

Standard setting 0000

3241 SP041 PTYP (PR)

0000 to FFFF HEX setting

Name Meaning when set to 0 Meaning when set to 1 ptyp Set the power supply type. (Refer to "9.4 (2) Power supply type" for details.) When using CV of 22kW or more with a spindle of large capacity (37kW or more), also turn the bit 8 ON. (Example) Setting value = CV370 + SP370 = 0137 Set "1" if the power supply external emergency stop is valid. (CV rotary switch is 4 or 5) Set "1" if the power supply unit is a resistance regeneration type. Set "0" if the power supply unit is a current regeneration type. If the power supply unit is a resistance regeneration type, set the type of resistance being used. (Refer to "9.4 (3) Regenerative resistance type" for details.) Set the driver model number. 0: MDS-C1-V1/V2/SP, MDS-B-V1/V2/SP,MDS-A-V1/V2/SP 1: MDS-B-SVJ2, MDS-A-SVJ 2: MDS-B-SPJ2, MDS-A-SPJ

rtyp

amp

3242 SP042 CRNG (PR)

C-axis detector range Synchronous tapping, spindle synchronous detector range NC communication frequency Dual cushion timer

This parameter is used to set the C-axis detector range. Set "0" for this parameter. "2" is used by Mitsubishi for testing.

0 to 7

3243 SP043 TRNG (PR)

This parameter is used to set the synchronous 0 to 7 tapping or spindle synchronous detector range. Set "0" for this parameter.

3244 SP044 TRANS (PR)

Set a frequency of data communication with NC.

0 to 32767 Standard: 0 Special: 1028 0

3245 SP045 CSNT

Set the cycle to add the increment values in the 0 to 1000 dual cushion process. (ms) When this setting value is increased, the dual cushion will increase, and the changes in the speed during acceleration/deceleration will become gradual. For an acceleration/deceleration time constant 0 to 1000 defined in SP019 (CSN1) , this parameter is used to provide smooth movement only at the start of acceleration/deceleration. As the value of this parameter is smaller, it moves smoother but the acceleration/deceleration time becomes longer. To make this parameter invalid, set "0".

3246 SP046 CSN2 (PR)

Speed command dual cushion

II - 270

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details Set the reset hysteresis width for a speed detection set value defined in SP020 (SDTS). Set the reset hysteresis width for a speed detection set value defined in SP020 (SDTS).

Setting range 0 to 1000 (r/min) 0 to 1000 (r/min)

Standard setting 30

3247 SP047 SDTR Speed (PR) detection reset value 3247 SP047 SDTR Speed (PR) detection reset value 3248 SP048 SUT (PR) 3249 SP049 TLM2 3250 SP050 TLM3 3251 SP051 TLM4 3252 SP052 TLM5 3253 SP053 TLM6 3254 SP054 TLM7

30

Speed reach Set the speed deviation rate with respect to the 0 to 100 range commanded speed for output of the speed (%) reach signal. Torque limit 2 Torque limit 3 Torque limit 4 Torque limit 5 Torque limit 6 Torque limit 7 Set the torque limit rate for the torque limit signal 010. Set the torque limit rate for the torque limit signal 011. Set the torque limit rate for the torque limit signal 100. Set the torque limit rate for the torque limit signal 101. Set the torque limit rate for the torque limit signal 110. Set the torque limit rate for the torque limit signal 111. Set the timer value until the excessive speed deviation alarm is output. The value of this parameter should be longer than the acceleration/deceleration time. Set the minimum value of the variable excitation rate. Select a smaller value when gear noise is too high. However, a larger value is effective for impact response. 1 to 120 (%) 1 to 120 (%) 1 to 120 (%) 1 to 120 (%) 1 to 120 (%) 1 to 120 (%) 0 to 60 (s)

15

20 30 40 50 60 70 12

3255 SP055 SETM Excessive (PR) speed deviation timer 3256 SP056 PYVR Variable excitation (min value)

0 to 100 (%)

50

3257 SP057 STOD Constant Set the value for judging when changing from a 0 to 50 (PR) constant to excessive speed command. (r/min) excessive judgment value 3258 SP058 SDT2 (PR) 3259 SP059 MKT (PR) Fixed control Set by Mitsubishi. constant Set "0" unless designated in particular. Winding changeover base shut-off timer Set the base shut-off time for contactor switching at winding changeover. Note that the contactor may be damaged with burning if the value of this parameter is too small. 0 50 to 10000 (ms)

0 150

3260 SP060 MKT2 Current limit Set the current limit time to be taken after (PR) timer after completion of contactor switching at winding winding changeover. changeover 3261 SP061 MKIL (PR) Current limit Set the current limit value during a period value after defined in SP060 (MKT2) after completion of winding contactor switching at winding changeover. changeover Not used. Set to "0".

0 to 10000 500 (ms)

0 to 120 (%)

75

3262 SP062

II - 271

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No. 3263 SP063 OLT (PR) 3264 SP064 OLL (PR)

Items Overload alarm detection time

Details Set the time constant for detection of the motor overload alarm.

Setting range 0 to 1000 (s)

Standard setting 60

Overload alarm Set the detection level of the motor overload 0 to 120 detection level alarm. (%) Set the magnification of speed loop proportional gain with respect to SP022 (VGNP1) at the maximum motor speed defined in SP017 (TSP). 0 to 100 (%)

110 100

3265 SP065 VCGN1 Target value of (PR) variable speed loop proportional gain

3266 SP066 VCSN1 Change Set the speed when the speed loop (PR) starting speed proportional gain change starts. of variable speed loop Proportional gain proportional SP022 gain
SP022 (SP065/100) SP066 SP017 Speed

0 to 32767 0 (r/min)

3267 SP067 VIGWA Change Set the speed where the current loop gain (PR) starting speed change starts. of variable current loop gain 3268 SP068 VIGWB Change (PR) ending speed of variable current loop gain 3269 SP069 VIGN (PR) Target value of variable current loop gain Set the speed where the current loop gain change ends.

0 to 32767 0 (r/min)

0 to 32767 0 (r/min)

Set the magnification of current loop gain (torque component and excitation component) for a change ending speed defined in SP068 (VIGWB). When this parameter is set to "0", the magnification is 1.

0 to 32767 0 (1/16-fold)

SP069(1/16)-fold 1-fold Speed SP067 SP068 SP017

SP017 (TSP) Maximum motor speed 0 to 6000 6001 to 8000 8001 or more

SP067 (VIGWA) 0 5000 5000

SP068 (VIGWB) 0 8000 10000

SP069 (VIGN) 0 45 64

II - 272

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items Machine resonance suppressio n filter frequency Fixed control constant

Details

Setting range

Standard setting 0

3270 SP070 FHz

When machine vibration occurs in speed and 0 to 3000 position control, set the frequency of the (Hz) required vibration suppression. Note that a value of 100Hz or more is set. Set to "0" when not used. Set by Mitsubishi. Set "0" unless designated in particular. 0

3271 (PR) 3272 (PR) 3273 (PR) 3274 (PR) 3275

SP071 VR2WA SP072 VR2WB SP073 VR2GN SP074 IGDEC SP075 R2KWS

8 r2ini

4 3 2 1 0 r2am r2lm r2dn no51 r2ch

bit 0 1 2 3 4 5 6 7 8 9 A B C D E F

Name Meaning when set to 0 Meaning when set to 1 r2ch This is used by Mitsubishi. no51 Set to "0" unless particularly designated. r2dm r2lm r2am

r2ini

This is used by Mitsubishi. Set to "0" unless particularly designated

3276 SP076 FONS

Machine resonance suppressio n filter operation speed Fixed control constant Fixed control constant

When the vibration increases in motor stop 0 to 32767 0 (ex. in orientation stop) when the machine (r/min) vibration suppression filter is operated by SP070, operate the machine vibration suppression filter at a speed of this parameter or more. When set to "0", this is validated for all speeds. Set by Mitsubishi. Set "14" unless designated in particular. Set by Mitsubishi. Set "0" unless designated in particular. 0 14

3277 SP077 TDSL (PR) 3278 SP078 FPWM (PR) 3279 SP079 ILMT (PR) 3280 SP080

Use not possible.

II - 273

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details This is used by Mitsubishi. Set to "0" unless particularly designated. 0

Setting range

Standard setting 0

3281 SP081 LMCA Fixed control 3282 SP082 LMCB constant 3283 SP083 3284 SP084 to to 3286 SP086 3287 SP087 DIQM (PR) Target value of variable torque limit magnification at deceleration

Use not possible.

Set the minimum value of variable torque limit at deceleration.

0 to 150 (%)

75

3288 SP088 DIQN (PR)

Speed for starting Set the speed where the torque limit value at 0 to 32767 3000 (r/min) change of deceleration starts to change. variable torque Torque limit limit magnificaInversely proportional tion at to speed 100% deceleration
SP087

SP088

SP017

3289 SP089 3290 SP090

Use not possible. Use not possible.

0 0

0 0

3291 SP091 OFSN Motor PLG Set the PLG offset value for the forward forward rotation rotation. offset compensa- Normally set to "0". tion 3292 SP092 OFSI Motor PLG Set the PLG offset value for the reverse reverse rotation rotation. offset compensa- Normally set to "0". tion Tolerable pulse check error

2048 to 0 2047 (1mv) 2048 to 0 2047 (1mv)

3293 SP093 ORE (PR)

Set this when detecting the pulse detector's 0 to 32767 0 pulse mistakes. (Valid only for full close control.) Set the filter time constant of load meter 0 to 32767 0 output. (2ms) When "0" is set, a filter time constant is set to 100ms. Set by Mitsubishi. Set "0" unless designated in particular. Set the gear ratio between the spindle end and the encoder end (except for the motor-built-in encoder) as indicated below.
Setting value 0 1 2 3 4 Gear ratio (deceleration) 1:1 1 : 1/2 1 : 1/4 1 : 1/8 1 : 1/16 Setting value 1 2 3 Gear ratio (acceleration) 1:2 1:4 1:3

3294 SP094 LMAV Load meter (PR) output filter

3295 SP095 VFAV (PR)

Fixed control constant

0 3 to 4

0 0

3296 SP096 EGAR Encoder gear (PR) ratio

II - 274

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items
F E ostp orze 7 6 vg8x mdir

Details Set the orientation specifications in bit units.

D C ksft gchg 5 fdir B A ips2 9 zdir 8

Setting range 0000 to FFFF HEX setting

Standard setting 0000

3297 SP097 SPECO Orientation (PR) specification

4 3 2 1 0 osc1 pyfx dmin odi2 odi1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 odi1 Orientation rotation direction odi2 00: Previous (the direction in which the motor has so far rotated under speed control) 01: Forward rotation 1 10: Backward rotation 11: Prohibited (Same as setting value = 10) Orientation in-position 2 dmin Orientation in-position advance invalid advance valid pyfx Excitation min. (50%) Excitation min. (50%) 3 during orientation servo during orientation servo lock invalid lock valid osc1 Indexing speed clamp Indexing speed clamp 4 invalid valid fdir Encoder detector Encoder detector 5 polarity: + polarity: mdir Magnetic sensor Magnetic sensor 6 polarity: + polarity: vg8x Speed gain *1/8 during Speed gain *1/8 during 7 torque limit valid torque limit invalid 8 zdir This is used by Mitsubishi. 9 Set to "0" unless particularly designated. A ips2 2nd in-position invalid 2nd in-position valid B C gchg Gain changeover during Gain changeover during orientation invalid orientation valid ksft Orientation virtual target Orientation virtual target D shift invalid shift valid E orze This is used by Mitsubishi. F ostp Set to "0" unless particularly designated.
In-position advance (bit 2) 0 (invalid) 0 (Invalid) Second in-position In-position signal in OINP width=1 Control output 4/ bit 4=1 Second in-position signal=0 Control output 4/ bit F=1 1 (valid) In-position signal in OINP width=1 Control output 4/ bit 4=1 Second in-position signal=0 Control output 4/ bit F=0 In-position signal in DINP width=1 Control output 4/ bit 4=1 Second in-position signal in OINP width = 0 Control output 4/ bit F=1

1 (Valid)

3298 SP098 VGOP (PR)

Speed loop gain proportional term in orientation mode Orientation mode speed loop gain integral term Orientation mode speed loop gain delay advance term

Set the speed loop proportional gain in orientation mode. When the gain is increased, rigidity is improved in the orientation stop but vibration and sound become larger.

0 to 1000 63 (1/s)

3299 SP099 VGOI (PR)

Set the speed loop integral gain in orientation 0 to 1000 60 mode. (0.1 1/s)

3300 SP100 VGOD (PR)

Set a loop gain delay advance gain in 0 to 1000 15 orientation mode. (0.1 1/s) When this parameter is set to "0", PI control is applied.

II - 275

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items Orientation advance in-position width Excessive error value in orientation mode Index positioning completion OFF time timer Torque limit value for orientation servo locking

Details

Setting range

Standard setting 16

3301 SP101 DINP (PR)

When using the orientation in-position advance 1 to 2880 function, set the in-position width that is larger (1/16) than the normal in-position width defined in SP004 (OINP). Set the excessive error width in orientation mode.

3302 SP102 OODR (PR)

0 to 32767 32767 (1/4 pulse) (1 pulse= 0.088)

3303 SP103 FTM (PR)

Set the time for forcedly turn OFF the index 0 to 10000 200 positioning completion signal (different from the (ms) orientation completion signal) after the leading edge of the indexing start signal. Set the torque limit value for orientation 0 to 120 in-position output. (%) If the external torque limit signal is input, the torque limit value set by this parameter is made invalid. 1 to 1000 (%) 100

3304 SP104 TLOR (PR)

3305 SP105 IQG0 (PR)

Current loop Set the magnification for current loop gain gain (torque component) at orientation completion. magnification 1 in orientation mode Current loop Set the magnification for current loop gain gain (excitation component) at orientation magnificacompletion. tion 2 in orientation mode Deceleration rate 2 in orientation mode Deceleration rate 3 in orientation mode Deceleration rate 4 in orientation mode Set the deceleration rate in orientation mode corresponding to the gear 001. When this parameter is set to "0", same as SP006 (CSP). Set the deceleration rate in orientation mode corresponding to the gear 010. When this parameter is set to "0", same as SP006 (CSP). Set the deceleration rate in orientation mode corresponding to the gear 011. When this parameter is set to "0", same as SP006 (CSP). Use not possible. Use not possible. Use not possible. Use not possible.

100

3306 SP106 IDG0 (PR)

1 to 1000 (%)

100

3307 SP107 CSP2

0 to 1000

3308 SP108 CSP3

0 to 1000

3309 SP109 CSP4

0 to 1000

3310 SP110 3311 SP111 3312 SP112 3313 SP113

0 0 0 0

II - 276

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items Orientation pulse miss check value

Details

Setting range

Standard setting 0

3314 SP114 OPER

An alarm "5C" will occur if the pulse miss 0 to 32767 value at the orientation stop exceeds this (360/4096) setting value. (Note that this is invalid when set to "0".) In this parameter, set the value to fulfill the following conditions. SP114 setting value > 1.5 SP004 (orientation in-position width) When the orientation clamp speed is 0 to 32767 changed by the control input, this parameter (r/min) setting will be used instead of SP005: OSP. Indexing speed clamp valid This parameter is used when (SP097: SPEC0-bit4 = 1). Minimum excitation rate when position control input or external input is selected. 0 to 100 (%)

3315 SP115 OSP2

Orientation motor speed clamp value 2

3316 SP116 OPYVR Minimum excitation value after changeover (2nd minimum excitation rate) 3317 SP117 ORUT 3318 SP118 ORCT Number of orientation retry times

This is used by Mitsubishi. Set to "0" unless particularly designated. Set the number of times to retry when an orientation or feedback error occurs. The warning (A9) is issued while retrying orientation, and an alarm (5C) is issued when the set number of times is exceeded.

0 0 to 100 (time)

0 0

3319 SP119 MPGH

Orientation Set the compensation magnification of the position gain orientation position loop gain for the H H winding winding. compensaH winding orientation position loop gain tion magnifi= SP001 (or SP002) SP119/256 cation When set to "0", will become the same as SP001 or SP002. Orientation Set the compensation magnification of the position gain orientation position loop gain for the L L winding winding. compensaL winding orientation position loop gain tion magnifi= SP001 (or SP002) SP120/256 cation When set to "0", will become the same as SP001 or SP002. Set the compensation magnification of the orientation deceleration rate for the H winding. Orientation deceleration rate for the H winding = SP006 SP121/256 When set to "0", will become the same as SP006.

0 to 2560 (1/256-fold)

3320 SP120 MPGL

0 to 2560 (1/256-fold)

3321 SP121 MPCSH Orientation deceleration rate H winding compensation magnification

0 to 2560 (1/256-fold)

II - 277

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details Set the compensation magnification of the orientation deceleration rate for the L winding. Orientation deceleration rate for the L winding = SP006 SP122/256 When set to "0", will become the same as SP006.

Setting range 0 to 2560 (1/256-fold)

Standard setting 0

3322 SP122 MPCSL Orientation deceleratio n rate L winding compensation magnification

3323 SP123 MGD0

Magnetic sensor output peak value

This parameter is used for adjustment of 1 to 10000 orientation operation of the magnetic sensor. Set the output peak value of the magnetic sensor. If a gap between the sensor and the magnetizing element is small, increase the value of this parameter. If it is large, decrease the value of this parameter.

Standard magnetizin g element: 542 Small magnetizin g element: 500 Standard magnetizin g element: 768 Small magnetizin g element: 440 Standard magnetizin g element: 384 Small magnetizin g element: 220 0

3324 SP124 MGD1

Magnetic sensor linear zone width

This parameter is used for adjustment of 1 to 10000 orientation operation of the magnetic sensor. Set the linear zone width of the magnetic sensor. If the radius of the mounted magnetizing element is large, decrease the value of this parameter. If it is small, increase the value of this parameter.

3325 SP125 MGD2

Magnetic sensor switching point

This parameter is used for adjustment of 1 to 10000 orientation operation of the magnetic sensor. Set the distance dimension from the target stop point at switching from position feedback to magnetic sensor output. Normally, set a value that is approx. 1/2 of the value defined in SP124. Use not possible. 0

3326 SP126 to to 3328 SP128

II - 278

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details Set the C-axis specifications in bit units.

F E D C B zrtn ptyp fb9x zrtd zrn2 7 vg8x 6 5 fdir 4 A 9 zdir 1 adin 8 ztyp 0 fclx

Setting range

Standard setting 0000

3329 SP129 SPECC C-axis (PR) specifications

3 2 phos rtrn

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 fclx Closed loop Semi-closed loop 0 (Gear 1 : 1 only) adin Interpolation A/D Interpolation A/D 1 compensation invalid compensation valid rtrn Position monitor during Position monitor during 2 ready OFF invalid ready OFF valid Vx4 synchronization 3 phos Normal (no compensation) compensation valid 4 fdir Position detector Position detector polarity 5 polarity (+) () 6 vg8x Speed gain 1/8 during Speed gain 1/8 during 7 torque limit valid torque limit invalid ztyp Z-phase type: Normal 8 Z-phase type: Start up only start up zdir Z-phase rising polarity 9 Z-phase rising polarity () (+) A B zrn2 This is used by Mitsubishi. C zrtd Set to "0" unless particularly designated. D E F zrtn fb9x ptyp Speed feedback Standard (PLG) Position control switch type: After zero point return Zero point return direction: CCW Speed feedback 90,000 pulse detector Position control switch type: After deceleration stop Zero point return direction: CW

II - 279

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items First position loop gain for cutting on C-axis Second position loop gain for cutting on C-axis Third position loop gain for cutting on C-axis Stop position loop gain for cutting on C-axis C-axis non-cutting speed loop gain proportional item C-axis non-cutting speed loop gain integral item C-axis non-cutting speed loop gain delay advance item First speed loop gain proportional item for C-axis cutting First speed loop gain integral item for cutting on C-axis First speed loop gain delay advance item for cutting on C-axis Second speed loop gain proportional item for cutting on C-axis

Details

Setting range

Standard setting 15

3330 SP130 PGC1

Set the position loop gain when the first gain 1 to 100 is selected for C axis cutting. (1/s)

3331 SP131 PGC2

Set the position loop gain when the second gain is selected for C axis cutting.

1 to 100 (1/s)

15

3332 SP132 PGC3

Set the position loop gain when the third gain 1 to 100 is selected for C-axis cutting. (1/s)

15

3333 SP133 PGC4

Set the position loop gain for stopping when 1 to 100 carrying out C-axis cutting. (1/s)

15

3334 SP134 VGCP0 (PR)

Set the speed loop proportional gain in C-axis non-cutting mode.

0 to 5000 (1/s)

63

3335 SP135 VGCI0 (PR)

Set the speed loop integral gain in C-axis non-cutting mode.

0 to 5000 (0.1 1/s)

60

3336 SP136 VGCD0 (PR)

Set the speed loop delay advance gain in 0 to 5000 C-axis non-cutting mode. (0.1 1/s) When this parameter is set to "0", PI control is exercised. Set the speed loop proportional gain when the first gain is selected for C-axis cutting. 0 to 5000 (1/s)

15

3337 SP137 VGCP1 (PR)

63

3338 SP138 VGCI1 (PR)

Set the speed loop integral gain when the first gain is selected for C-axis cutting.

0 to 5000 (0.1 1/s)

60

3339 SP139 VGCD1 (PR)

Set the speed loop delay advance gain when 0 to 5000 the first gain is selected for curing on the (0.1 1/s) C-axis. When this parameter is set to "0", PI control is applied. Set the speed loop proportional gain when the second gain is selected for C-axis cutting. 0 to 5000 (1/s)

15

3340 SP140 VGCP2 (PR)

63

II - 280

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details

Setting range

Standard setting 60

3341 SP141 VGCI2 (PR)

Second speed Set the speed loop integral gain when the 0 to 5000 loop gain second gain is selected for C-axis cutting. (0.1 1/s) integral item for cutting on C-axis Set the speed loop delay advance gain when the second gain is selected for C-axis cutting. When this parameter is set to "0", PI control is applied. 0 to 5000 (0.1 1/s)

3342 SP142 VGCD2 Second speed loop gain delay (PR) advance item for cutting on C-axis 3343 SP143 VGCP3 Third speed (PR) loop gain proportional item for cutting on C-axis 3344 SP144 VGCI3 (PR)

15

Set the speed loop proportional gain when 0 to 5000 the third gain is selected for C-axis cutting. (1/s)

63

Third speed Set the speed loop integral gain when the loop gain third gain is selected for C-axis cutting. integral item for cutting on C-axis Set the speed loop delay advance gain when the third gain is selected for C-axis cutting. When this parameter is set to "0", PI control is applied.

0 to 5000 (0.1 1/s)

60

3345 SP145 VGCD3 Third speed (PR) loop gain delay advance item for cutting on C-axis 3346 SP146 VGCP4 Speed loop (PR) gain proportional item for stop of cutting on C-axis 3347 SP147 VGCI4 (PR)

0 to 5000 (0.1 1/s)

15

Set the speed loop proportional gain when 0 to 5000 C-axis cutting is stopped. (1/s)

63

Speed loop Set the speed loop integral gain when gain integral C-axis cutting is stopped. item for stop of cutting on C-axis Set the speed loop delay advance gain when C-axis cutting is stopped. When this parameter is set to "0", PI control is applied.

0 to 5000 (0.1 1/s)

60

3348 SP148 VGCD4 Speed loop (PR) gain delay advance item for stop of cutting on C-axis 3349 SP149 CZRN C-axis zero point return speed

0 to 5000 (0.1 1/s)

15

This parameter is valid when SP129 1 to 500 (SPECC) bitE is set to "0". (r/min) Set the zero point return speed used when the speed loop changes to the position loop. This parameter is valid when SP129 (SPECC) bitE is set to "0". Set the deceleration rate where the machine starts to decelerate when it returns to the target stop point during C-axis zero point return. When the machine tends to overshoot at the stop point, set the smaller value.

50

3350 SP150 CPDT

C-axis zero point return deceleration point

1 to 10000 1

II - 281

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items C-axis zero point return shift amount (low byte) C-axis zero point return shift amount (high byte) C-axis in-position width

Details This parameter is valid when SPECC (SP129) bitE is set to "0". Set the C-axis zero point position.

Setting range

Standard setting

3351 SP151 CPSTL

3352 SP152 CPSTH

HEX setting H: 0000 00000000 L: 0000 to FFFFFFFF (1/1000)

3353 SP153 CINP

Set the position error range in which the in-position signal is output on the C-axis.

0000 to 03E8 FFFF (1/1000) HEX setting HEX setting H: 0001 00000000 L: D4C0 to FFFFFFFF (1/1000)

3354 SP154 CODRL Excessive Set the excessive error width on the C-axis. (PR) error width on C-axis (low byte) 3355 SP155 CODRH Excessive (PR) error width on C-axis (high byte) 3356 SP156 OVSH C-axis overshoot compensation

Set this to prevent overshooting when 0 to 1000 shifting from movement to stopping with (0.1%) C-axis control. (Set this referring to the load meter display when overshooting occurred.) Not used. Set to "0". 0

3357 SP157 to to 3358 SP158 3359 SP159 CPY0 C-axis non-cutting variable excitation ratio

Set the minimum value of variable excitation ratio for non-cutting on the C-axis .

0 to 100 (%) 50

3360 SP160 CPY1

C-axis cutting Set the minimum variable excitation ratio variable for cutting on the C-axis. excitation ratio Current loop gain magnification 1 for non-cutting on C-axis Current loop gain magnification 2 for non-cutting on C-axis Current loop gain magnification 1 for cutting on C-axis

0 to 100 (%) 100

3361 SP161 IQGC0 (PR)

Set the magnification of current loop gain 1 to 1000 (torque component) for C-axis non-cutting. (%)

100

3362 SP162 IDGC0 (PR)

Set the magnification of current loop gain (excitation component) for C-axis non-cutting.

1 to 1000 (%)

100

3363 SP163 IQGC1 (PR)

Set the magnification of current loop gain (torque component) for C-axis cutting.

1 to 1000 (%)

100

II - 282

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details Set the magnification of current loop gain (excitation component) for C-axis cutting.

Setting range 1 to 1000 (%)

Standard setting 100

3364 SP164 IDGC1 Current loop (PR) gain magnification 2 for cutting on C-axis 3365 SP165 PG2C

C-axis position Set the second position loop gain when 0 to 999 loop gain 2 high-gain control is carried out for control of (1/s) the C-axis. This parameter is applied to all the operation modes of C-axis control. When this function is not used, assign "0". C-axis position Set the third position loop gain when 0 to 999 loop gain 3 high-gain control is carried out for control of (1/s) the C-axis. This parameter is applied to all the operation modes of C-axis control. When this function is not used, assign "0". Position loop gain for increased spindle holding force Speed loop gain proportional item for increased spindle holding force Speed loop gain integral item for increased spindle holding force Speed loop gain delay advance item for increased spindle holding force Set the position loop gain for when the disturbance observer is valid. 0 to 100 (1/s)

3366 SP166 PG3C

3367 SP167 PGU (PR)

15

3368 SP168 VGUP (PR)

Set the speed loop gain proportional item 0 to 5000 for when the disturbance observer is valid. (1/s)

63

3369 SP169 VGUI (PR)

Set the speed loop gain integral item for when the disturbance observer is valid.

0 to 5000 (0.1 1/s)

60

3370 SP170 VGUD (PR)

Set the speed loop gain delay advance item for when the disturbance observer is valid.

0 to 5000 (0.1 1/s)

15

3371 SP171 to to 3376 SP176

Not used. Set to "0".

II - 283

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details Set the spindle synchronous specifications in bit units.

F E D Odx8 5 fdir C B A 9 8 phos 0 fclx

Setting range 0000 to FFFF HEX setting

Standard setting 0000

3377 SP177 SPECS Spindle (PR) synchronous specifications

3 pyfx

2 rtrn

1 adin

bit Name Meaning when set to 0 0 fclx Closed loop adin Interpolation A/D 1 compensation invalid rtrn Position monitor during 2 ready OFF invalid pyfx Normal excitation 3 4 5 6 7 8 9 A B C odx8 D E F Magnification of excessive error width 8 times invalid (Used with SPJ) fdir Position detector direction (positive direction)

Meaning when set to 1 Semi-closed loop Interpolation A/D compensation valid Position monitor during ready OFF valid Position loop excitation fixed (strong) Position detector direction (negative direction)

Magnification of excessive error width 8 times valid

3378 SP178 VGSP (PR)

Spindle Set the speed loop proportional gain in spindle 0 to 1000 synchronous synchronous mode. (1/s) speed loop gain proportional term Spindle Set the speed loop integral gain in spindle synchronous synchronous mode. speed loop gain integral term 0 to 1000 (0.1 1/s)

63

3379 SP179 VGSI (PR)

60

3380 SP180 VGSD (PR)

Spindle Set the speed loop delay advance gain in 0 to 1000 synchronous spindle synchronous mode. (0.1 1/s) speed loop gain When this parameter is set to "0", PI control is delay advance applied. term Spindle synchronous Target value of variable speed loop proportional gain Set the magnification of speed loop proportional gain with respect to SP178 (VGSP) at the maximum speed defined in SP017 (TSP) in spindle synchronous mode. 0 to 100 (%)

15

3381 SP181 VCGS (PR)

100

II - 284

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details

Setting range 0 to 32767 (r/min)

Standard setting 0

3382 SP182 VCSS (PR)

Spindle Set the speed when the speed loop synchronous proportional gain change starts in the Change spindle synchronous mode. starting speed of variable Proportional gain speed loop SP178 proportional gain SP178
(SP181/100) SP182 SP017 Speed

3383 SP183 SYNV

Spindle synchronousS ync matching speed Spindle synchronous Acceleration rate feed forward gain Spindle synchronous In-position width Spindle synchronous Excessive error width Spindle synchronous Current loop gain magnification1 Spindle synchronous Current loop gain magnification 2 Spindle synchronous Position loop gain 2 Spindle synchronous Position loop gain 3

For changeover from the speed loop to the 0 to 1000 position loop in the spindle synchronous (r/min) mode, set a speed command error range for output of the synchronous speed matching signal. Set the acceleration rate feed forward gain 0 to 1000 in the spindle synchronous mode. (%) This parameter is used only with the SPJ2.

20

3384 SP184 FFCS (PR)

3385 SP185 SINP

Set the position error range for output of the 1 to 2880 in-position signal in the spindle (1/16) synchronous mode. Set the excessive error width in the spindle 1 to 32767 synchronous mode. ( pulse) (1 pulse =0.088) Set the magnification of current loop gain (torque component) in the spindle synchronous mode. 1 to 1000 (%)

16

3386 SP186 SODR (PR)

32767

3387 SP187 IQGS (PR)

100

3388 SP188 IDGS (PR)

Set the magnification of current loop gain (excitation component) in the spindle synchronous mode.

1 to 1000 (%)

100

3389 SP189 PG2S

Set the second position loop gain when high-gain control is carried out in the spindle synchronous mode. When this parameter function is not used, set to "0". Set the third position loop gain when high-gain control is carried out in the spindle synchronous mode. When this parameter function is not used, set to "0". Use not possible. Not used. Set to "0".

0 to 999 (1/s)

3390 SP190 PG3S

0 to 999 (1/s)

3391 SP191 3392 SP192

II - 285

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details

Setting range 0000 to FFFF HEX setting

Standard setting 0000

3393 SP193 SPECT Synchronized Set the synchronized tapping specifications in (PR) tapping bit units. specificaF E D C B A 9 8 tions zrtn ptyp od8x phos
7 6 5 fdir 4 cdir 3 pyfx 2 1 adin 0 fclx

bit Name Meaning when set to 0 Meaning when set to 1 fclx Closed loop Semi-closed loop 0 (Gear 1 : 1 only) adin Interpolation A/D Interpolation A/D 1 compensation invalid compensation valid rtrn Position monitor during Position monitor during 2 ready OFF invalid ready OFF valid pyfx Normal excitation Position loop excitation 3 fixed (strong) 4 cdir Command polarity (+) Command polarity () Position detector fdir Position detector 5 polarity () polarity (+) 6 7 phos Normal Synchronized tapping position compensation 8 (no compensation) valid 9 A B C od8x Magnification of Magnification of D excessive error width excessive error width 8 times invalid 8 times valid ptyp Position control switch Position control switch E type: After zero point type: After deceleration return stop zrtn Zero point return Zero point return F direction: CCW direction: CW

3394 SP194 VGTP (PR)

Synchronized Set the speed loop proportional gain in tapping synchronized tapping mode. speed loop gain proportional term Synchronized Set the speed loop integral gain in tapping synchronized tapping mode. speed loop gain integral term Synchronized tapping speed loop gain delay advance term Set the speed loop delay advance gain in synchronized tapping mode. When this parameter is set to "0", PI control is applied.

0 to 1000 (1/s)

63

3395 SP195 VGTI (PR)

0 to1000 (0.1 1/s)

60

3396 SP196 VGTD (PR)

0 to 1000 (0.1 1/s)

15

3397 SP197 3398 SP198 VCGT (PR) Synchronized tapping target value of variable speed loop proportional gain

This is used by Mitsubishi. Set to "0" unless particularly designated.

0 100

Set the magnification of speed loop proportional 0 to 100 gain with respect to SP194 (VGTP) at the (%) maximum motor speed defined in SP017 (TSP) in synchronized tapping mode.

II - 286

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items

Details Set the speed where the speed loop proportional gain change starts during synchronized tapping.
Proportional gain SP194 SP194 (SP198/100) SP199 SP017

Setting range

Standard setting

3399 SP199 VCST Synchronized (PR) tapping change starting speed of variable speed loop proportional gain

0 to 32767 0 (r/min)

Speed

3400 SP200 FFC1 Synchronized tapping (PR) acceleration feed forward gain (gear 1)

Set the acceleration feed forward gain for selection of gear 000 during synchronized tapping. This parameter should be used when an error of relative position to Z-axis servo is large.

0 to 1000 (%)

3401 SP201 FFC2 Synchronized tapping Set the acceleration feed forward gain (PR) acceleration feed for selection of gear 001 during forward gain synchronized tapping. (gear 2) 3402 SP202 FFC3 Synchronized tapping Set the acceleration feed forward gain (PR) acceleration feed for selection of gear 010 during forward gain synchronized tapping. (gear 3) 3403 SP203 FFC4 Synchronized tapping Set the acceleration feed forward gain (PR) acceleration feed for selection of gear 011 during forward gain synchronized tapping. (gear 4) 3404 SP204 to to 3413 SP213 Not used. Set to "0".

0 to 1000 (%)

0 to 1000 (%)

0 to 1000 (%)

3414 SP214 TZRN Synchronized tapping This parameter is valid when SP193 zero point return (SPECT) bitE is set to "0". speed Set the zero point return speed used when the speed loop changes to the position loop.

0 to 500 (r/min)

50

3415 SP215 TPDT Synchronized tapping This parameter is valid when SP193 0 to 10000 1 zero point return (SPECT) bitE is set to "0". (pulse) deceleration rate Set the deceleration rate where the machine starts to decelerate when it returns to the target stop point during synchronized tapping zero point return. When the machine tends to overshoot at the stop point set a smaller value. 3416 SP216 TPST Synchronized tapping This parameter is valid when SP193 0 to 4095 zero point return shift (SPECT) bitE is set to "0". amount Set the synchronized tapping zero point position. 3417 SP217 TINP Synchronized tapping Set the position error range for output of 1 to 2880 in-position the in-position during synchronized (1/16) width tapping. 0

16

II - 287

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items Synchronized tapping excessive error width

Details Set the excessive error width during synchronized tapping.

Setting range 1 to 32767 (pulse) (1 pulse =0.088) 1 to 1000 (%)

Standard setting 32767

3418 SP218 TODR (PR)

3419 SP219 IQGT (PR)

Synchronized Set the magnification of current loop gain tapping current (torque component) during synchronized loop gain tapping. magnification 1 Synchronized Set the magnification of current loop gain tapping current (excitation component) during loop gain synchronized tapping. magnification 2 Synchronized tapping position loop gain 2 Synchronized tapping position loop gain 3

100

3420 SP220 IDGT (PR)

1 to 1000 (%)

100

3421 SP221 PG2T

Set the second position loop gain when 0 to 999 high-gain control is applied during (1/s) synchronized tapping. When this parameter is not used, set to "0". Set the third position loop gain when 0 to 999 high-gain control is applied during (1/s) synchronized tapping. When this parameter is not used, set to "0".

3422 SP222 PG3T

3423 SP223 SPDV

Speed monitor Set the spindle limit speed in the door open 0 to 800 speed state. (r/min) (Invalid when 0 is set.) If the spindle end speed exceeds this setting value when the door is open, the speed monitor error (5E) will occur. Speed monitor Set the time (continuous) to detect alarms. 0 to 2813 time (Detected instantly when 0 is set.) (3.5ms) If gain changeover is valid (SP097: 0 to 2560 SPEC0-bitC=1) during orientation, set the (1/256-fold) magnification of each gain changed to after in-position.

3424 SP224 SPDF

0 0

3425 SP225 OXKPH Position loop gain magnification after orientation gain changeover (H coil) 3426 SP226 OXKPL Position loop gain magnification after orientation gain changeover (L coil)

0 to 2560 (1/256-fold)

3427 SP227 OXVKP Speed loop proportional gain magnification after orientation gain changeover

0 to 2560 (1/256-fold)

II - 288

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No.

Items Speed loop cumulative gain magnification after orientation gain changeover

Details If gain changeover is valid (SP097: SPEC0-bitC=1) during orientation, set the magnification of each gain changed to after in-position.

Setting range 0 to 2560 (1/256-fold)

Standard setting 0

3428 SP228 OXVKI

3429 SP229 OXSFT Orientation virtual target shift amount 3430 SP230 3431 SP231 3432 SP232 3433 SP233 JL (PR)

Set the amount to shift the target position 0 to 2048 when orientation virtual target position is (360/4096) valid (SP097: SPEC0-bitD=1). Use not possible.

Disturbance Set the ratio of the motor inertia + load observer general inertia and motor inertia. inertia scale

0 to 5000 (%)

Setting Motor inertia + load inertia 100 value = Motor inertia

(Normally, set "100" or more. When less than "50" is set, the setting will be invalid.) 3434 SP234 OBS1 (PR) Disturbance observer low path filter frequency Set the frequency of the low path filter for 0 to 1000 when the disturbance observer is valid. (1/s) Setting (1/s) = 2f f: Approx. 1.5 times the disturbance frequency Set the gain for the disturbance observer. 0 to 500 (%) 0 0 0 0 0

3435 SP235 OBS2 (PR) 3436 SP236 OBS3 3437 SP237 3438 SP238 to to 3439 SP239 3440 SP240 3441 SP241 3442 SP242 Vavx 3443 SP243 UTTM 3444 SP244 OPLP 3445 SP245 PGHS 3446 SP246 TEST 3447 SP247 to to 3448 SP248 3449 SP249 SM0

Disturbance observer gain

This is used by Mitsubishi. 0 Set to "0" unless particularly designated. Not used. Set to "0". Use not possible. 0 0

Use not possible. Use not possible.

0 0

0 0 0 0 0 0 0 0

0 This is used by Mitsubishi. Set to "0" unless particularly designated. 0 0 0 0 Use not possible. 0

Speed meter speed

Set the motor rotation speed when the 0 to 32767 speed meter 10V is output. (r/min) When set to "0", this parameter becomes the same as SP017 (TSP).

II - 289

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No. 3450

Items SP250 LM0

Details Load meter Set the voltage when the load meter voltage 120% is output. When set to "0", this becomes 10V. Use not possible.

Setting range 0 to 10 (V) 0 0

Standard setting

3451 to 3452 3453

SP251 to SP252 SP253 DA1NO D/A output channel 1 data number

Set the output data number for channel 1 32768 to of the D/A output function. 32767 When set to "0", the output is speedometer. Refer to "9.4 (1) For D/A output functions". Set the output data number for channel 2 32768 to of the D/A output function. 32767 When set to "0", the output is load meter. Refer to "9.4 (1) For D/A output functions". Set the data magnification for channel 1 32768 to of the D/A output function. 32767 The output magnification is the setting (1/256-fold) value divided by 256. When set to "0", the output magnification becomes 1-fold, in the same manner as when "256" is set. Refer to "9.4 (1) For D/A output functions". Set the data magnification for channel 2 32768 to of the D/A output function. 32767 The output magnification is the setting (1/256-fold) value divided by 256. When set to "0", the output magnification becomes 1-fold, in the same manner as when "256" is set. Refer to "9.4 (1) For D/A output functions". This parameter is valid only in the following two conditional cases: (a) In case that SP034 (SFNC2) bit0=1 and SP034 (SFNC2) bit2=0 Set the motor constants when using a special motor, not described in the SP040 (MTYP) explanation and when not using the coil changeover motor. (b) In case that SP034 (SFNC2) bit0=1 and SP034 (SFNC2) bit2=1 Set the motor constant of the H coil of the coil changeover motor. (Note) It is not allowed for the user to change the setting.

3454

SP254 DA2NO

D/A output channel 2 data number

3455

SP255 DA1MPY DA output channel 1 magnification

3456

SP256 DA2MPY DA output channel 2 magnification

3457 (PR) to 3520 (PR)

SP257 RPM to SP320 BSD

Motor constant (H coil)

0000 to 0000 FFFF HEX setting

II - 290

9. 9.2

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SPINDLE PARAMETERS

No. 3521 (PR) to 3584 (PR)

Items SP321 RPML to SP384 BSDL Motor constant (L coil)

Details This parameter is valid only in the following conditional case: (a) In case that SP034 (SFNC2) bit0=1 and SP034 (SFNC2) bit2=1 Set the motor constant of the L coil of the coil changeover motor. (Note) It is not allowed for the user to change the setting.

Setting range

Standard setting

0000 to 0000 FFFF HEX setting

II - 291

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

9.3 MDS-C1-SPM SPINDLE PARAMETERS

For parameters marked with a (PR) in the tables, turn the CNC power OFF after setting. The parameters will be valid after the power is turned ON again. The "fixed control constants" and "fixed control bits" in this section are set by Mitsubishi.

! CAUTION
! !

Do not make remarkable adjustments or changes of the parameters as the operation may become unstable. In the explanation on bits, set all bits not used, including blank bits, to 0. Setting range Standard setting 100

No. 3201 SP001 PGM

Items Magnetic sensor and motor built-in encoder orientation position loop gain

Details

As the set value is larger, the orientation 0 to 2000 time becomes shorter and servo rigidity is (0.1 1/s) increased. However, vibration is increased and the machine becomes likely to overshoot.

3202 SP002 PGE

Encoder As the set value is larger, the orientation 0 to 2000 orientation time becomes shorter and servo rigidity is (0.1 1/s) position loop gain increased. However, vibration is increased and the machine becomes likely to overshoot. 1 to 200 (1/s)

100

3203 SP003 PGC0 C-axis non-cutting Set the position loop gain in C-axis position loop gain non-cutting mode. During non-cutting (rapid traverse, etc.) with the C axis control, this position loop gain setting is valid. 3204 SP004 OINP Orientation in-position width 3205 SP005 OSP (PR) Set the position error range in which an orientation completion signal is output.

15

1 to 2880 (1/16 )

16 0

Orientation mode Set the motor speed limit value to be used 0 to 32767 changing speed when the speed loop is changed to the (r/min) limit value position loop in orientation mode. When this parameter is set to "0", SP017 (TSP) becomes the limit value. Orientation mode As the set value is larger, the orientation deceleration rate time becomes shorter. However, the machine becomes likely to overshoot. Set the stop position for orientation. (i) Motor built-in encoder, encoder: Set the value by dividing 360 by 4096. (ii) Magnetic sensor: Divide 5 to +5 by 1024 and put 0 for 0. Not used. Set to "0". Synchronized tapping Position loop gain Set the spindle position loop gain in synchronized tapping mode. 1 to 1000

3206 SP006 CSP

20

3207 SP007 OPST In-position shift amount for orientation

(i) 0 to 4095 0 (ii) 512 to 512

3208 SP008 3209 SP009 PGT

0 1 to 200 (1/s)

0 15

II - 292

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No. 3210 SP010 PGS

Items Spindle synchronous position loop gain

Details Set the spindle position loop gain in spindle synchronization mode.

Setting range 1 to 200 (1/s)

Standard setting 15

3211 SP011 to to 3216 SP016 3217 SP017 TSP (PR) 3218 SP018 ZSP (PR) 3219 SP019 CSN1 (PR) Maximum motor speed Motor zero speed Speed cushion 1

Use not possible.

Set the maximum motor speed of the spindle.

1 to 32767 (r/min)

6000 50 30

Set the motor speed for which zero-speed 1 to 1000 output is performed. (r/min) Set the time constant for a speed 1 to 32767 command from "0" to the maximum speed. (10ms) (This parameter is invalid in position loop mode.) Set the motor speed so for which speed 0 to 32767 detection output is performed. (r/min) Usually, the setting value is 10% of SP017 (TSP).

3220 SP020 SDTS (PR)

Speed detection set value

600

3221 SP021 TLM1

Torque limit 1 Set the torque limit rate for torque limit signal 001.

0 to 120 (%) 10 63

3222 SP022 VGNP1 Speed loop (PR) gain proportional term under speed control 3223 SP023 VGNI1 (PR) Speed loop gain integral term under speed control Spindle gear teeth count 1 Spindle gear teeth count 2 Spindle gear teeth count 3 Spindle gear teeth count 4 Motor shaft gear teeth count 1 Motor shaft gear teeth count 2 Motor shaft gear teeth count 3 Motor shaft gear teeth count 4

Set the speed loop proportional gain in 0 to 1000 speed control mode. (1/s) When the gain is increased, response is improved but vibration and sound become larger. Set the speed loop integral gain in speed 0 to 1000 control mode. (0.1 1/s) Usually, set a value in proportion to SP022 (VGNP1). Use not possible. 0 Set the number of gear teeth of the spindle 1 to 32767 corresponding to gear 000. Set the number of gear teeth of the spindle 1 to 32767 corresponding to gear 001. Set the number of gear teeth of the spindle 1 to 32767 corresponding to gear 010. Set the number of gear teeth of the spindle 1 to 32767 corresponding to gear 011. Set the number of gear teeth of the motor 1 to 32767 shaft corresponding to gear 000. Set the number of gear teeth of the motor 1 to 32767 shaft corresponding to gear 001. Set the number of gear teeth of the motor 1 to 32767 shaft corresponding to gear 010. Set the number of gear teeth of the motor 1 to 32767 shaft corresponding to gear 011.

60

3224 SP024 3225 SP025 GRA1 (PR) 3226 SP026 GRA2 (PR) 3227 SP027 GRA3 (PR) 3228 SP028 GRA4 (PR) 3229 SP029 GRB1 (PR) 3230 SP030 GRB2 (PR) 3231 SP031 GRB3 (PR) 3232 SP032 GRB4 (PR)

0 1 1 1 1 1

II - 293

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items

Details Set the spindle function 1 in bit units.

F poff E D C ront 4 B A 9 8 pycal pychg 1 0

Setting range 0000 to FFFF HEX setting

Standard setting 0000

3233 SP033 SFNC1 Spindle (PR) function 1

7 6 pyst pyoff

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 1 2 3 4 5 6 7 8 9 A This is used by Mitsubishi. B Set to "0" unless particularly designated. C ront Normal ready ON High-speed ready ON This is used by Mitsubishi. D Set to "0" unless particularly designated. E poff Contactor hold at NC Contactor hold at NC F power OFF invalid power OFF valid

3234 SP034 SFNC2 Spindle (PR) function 2

Set the spindle function 2 in bit units.

F E D C B A 9 8

0000 to FFFF HEX setting

0000

3 2 1 0 mkc2 mkch Mk3c mts1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 0 mts1 Special motor constant invalid 1 Mk3c 3-step coil changeover function invalid 2 mkch Winding switch function invalid mkc2 Coil changeover function 2 invalid 3 4 5 6 7 8 9 A B C D E F Meaning when set to 1 Special motor constant setting valid 3-step coil changeover function valid Winding switch function valid Coil changeover function 2 valid (Turns ON simultaneously with bit 2)

(Note) bit3 mkc2 must be handled on the NC side.

II - 294

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No. 3235 SP035 (PR)

Items SFNC3 Spindle function 3

Details Set the spindle function 3 in bit units.

F E D C B A 9 8

Setting range 0000 to FFFF HEX setting

Standard setting 0000

2 1 0 mwid lwid hwid

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 hwid H coil output character0 istics change invalid lwid L coil output character1 istics change invalid 2 mwid M coil output characteristics change invalid 3 4 5 6 7 8 (Used with SPJ.) 9 A B C D E F Meaning when set to 1 H coil output characteristics change valid L coil output characteristics change valid M coil output characteristics change valid

3236

SP036

Not used. Set to "0".

II - 295

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items Spindle function 5

F E D

Details Set the spindle function 5 in bit units.

C B A 9 8 nsno nosg 1 0 enco

Setting range 0000 to FFFF HEX setting

Standard setting 0000

3237 SP037 SFNC5 (PR)

2 plgo

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 0 enco Encoder orientation invalid 1 2 plgo PLG orientation invalid 3 4 5 6 7 nosg No-signal detection type 8 (Always monitoring) 9 A B C D E F nsno No-signal detection valid Meaning when set to 1 Encoder orientation valid PLG orientation valid

Monitoring only in position loop or orientation-mode No-signal detection invalid

(Note) For bit0 to 2, do not set two bits or more to "1" at the same time.

3238 SP038 SFNC6 (PR)

Spindle function 6

Set the spindle function 6 in bit units.

F E D C XFzs 4 tdn B A 9 8 pl80 sdt2 1 0 alty

0000 to FFFF HEX setting

0000

7 6 hzrn orm

3 2 plg2 pftm

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 alty Deceleration stop during 0 special alarm invalid 1 pftm Encoder feedback serial 2 communication invalid plg2 Semi-closed pulse 3 output signal 2 invalid 4 tdn Fixed control bit 5 orm Orientation start memo 6 invalid 7 hzrn Fixed control bit 8 sdt2 9 pl80 A B C XFzs Fixed control bit D E F Meaning when set to 1 Deceleration stop during special alarm valid Encoder feedback serial communication valid Semi-closed pulse output signal 2 valid

Orientation start memo valid

II - 296

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No. 3239 (PR)

Items SP039 ATYP Amplifier type

Details Set the amplifier type. Set each amplifier type or "0"
Parameter setting 0000 0001 0002 0003 0004 0005 0006 0007 0008 0009 000A 000B 000C 000D 000E 000F 0010 Amplifier type SPM-110 SPM-150 SPM-185 SPM-220 SPM-260 SPM-300 (SPM-370) (SPM-450)

Setting range 0000 to FFFF HEX setting

Standard setting 0000

(Note) (SPM-370) and (SPM-450) are used with MDS-B-SPM. 3240 (PR) SP040 MTYP Motor type
F E D C B A 9 8

2 motr

0000 to FFFF HEX setting

0000

bit Name Details motr Set the motor type. 0 Set "0" when using a special motor. 1 2 3 4 5 6 7 8 9 A B C D E F

II - 297

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items Power supply type Power supply type

F E amp 7 6 5 D

Details

Setting range
A rtyp 9 8

Standard setting 0000

3241 SP041 PTYP (PR)

0000 to FFFF HEX setting

4 ptyp

bit 0 1 2 3 4 5 6 7 8 9 A B C D E F

Name Details ptyp Set the power supply type. (Refer to "9.4 (2) Power supply type" for details.) When using CV of 22kW or more with a spindle of large capacity (37kW or more), also turn the bit 8 ON. (Example) Setting value = CV370 + SPM370 = 137H

rtyp

Set "1" if the power supply external emergency stop is valid. (CV rotary switch is 4 or 5) Set "1" if the power supply unit is a resistance regeneration type. Set "0" if the power supply unit is a current regeneration type. If the power supply unit is a resistance regeneration type, set the type of resistance being used. (Refer to "9.4 (3) Regenerative resistance type" for details.) Set the driver model number. 0: MDS-C1-V1/V2/SP, MDS-B-V1/V2/SP,MDS-A-V1/V2/SP 1: MDS-B-SVJ2, MDS-A-SVJ 2: MDS-B-SPJ2, MDS-A-SPJ

amp

3242 SP042 CRNG (PR)

C-axis detector This parameter is used to set the C-axis range detector range. Set "0" for this parameter. "2" is used by Mitsubishi for testing. Synchronous tapping, spindle synchronous detector range

0 to 7

3243 SP043 TRNG (PR)

This parameter is used to set the 0 to 7 synchronous tapping or spindle synchronous detector range. Set "0" for this parameter. Set a frequency of data communication with NC.

3244 SP044 TRANS NC communi(PR) cation frequency 3245 SP045 CSNT Dual cushion timer

0 to 32767 Standard: 0 Special: 1028 0

Set the cycle to add the increment values in 0 to 1000 the dual cushion process. (ms) When this setting value is increased, the dual cushion will increase, and the changes in the speed during acceleration/deceleration will become gradual.

II - 298

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items

Details For an acceleration/deceleration time constant defined in SP019 (CSN1) , this parameter is used to provide smooth movement only at the start of acceleration/deceleration. As the value of this parameter is smaller, it moves smoother but the acceleration/deceleration time becomes longer. To make this parameter invalid, set "0".

Setting range 0 to 1000

Standard setting 0

3246 SP046 CSN2 Speed (PR) command dual cushion

3247 SP047 SDTR Speed (PR) detection reset value 3248 SP048 SUT (PR) 3249 SP049 TLM2 3250 SP050 TLM3 3251 SP051 TLM4 3252 SP052 TLM5 3253 SP053 TLM6 3254 SP054 TLM7 Speed reach range Torque limit 2 Torque limit 3 Torque limit 4 Torque limit 5 Torque limit 6 Torque limit 7

Set the reset hysteresis width for a speed 0 to 1000 detection set value defined in SP020 (SDTS). (r/min) Set the speed deviation rate with respect to the commanded speed for output of the speed reach signal. Set the torque limit rate for the torque limit signal 010. Set the torque limit rate for the torque limit signal 011. Set the torque limit rate for the torque limit signal 100. Set the torque limit rate for the torque limit signal 101. Set the torque limit rate for the torque limit signal 110. Set the torque limit rate for the torque limit signal 111. 0 to 100 (%) 1 to 120 (%) 1 to 120 (%) 1 to 120 (%) 1 to 120 (%) 1 to 120 (%) 1 to 120 (%)

30

15

20 30 40 50 60 70

3255 SP055 SETM Excessive Set the timer value until the excessive speed 0 to 60 (s) 12 (PR) speed deviation deviation alarm is output. timer The value of this parameter should be longer than the acceleration/deceleration time. 3256 SP056 Use not possible. 0 0 0 3257 SP057 STOD Constant Set the value for judging when changing from 0 to 50 (PR) a constant to excessive speed command. (r/min) excessive judgment value 3258 SP058 SDT2 (PR) 2nd speed detection speed

0 to 32767 0 Set the speed for turning the 2nd speed (r/min) detection ON. (This is valid only when SP038: SFNC6-bit8 is set to "1".) If the speed drops below this set speed, the 2nd speed detection will turn ON. When the speed reaches this set speed +15r/min or more, the 2nd speed detection will turn OFF. If SP034: SFNC2-bit1 is set to "1", this will be the medium-speed and high-speed coil changeover speed. The speed detection reset width follows the SP047 (speed detection reset width) setting.

II - 299

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No. 3259 SP059 MKT (PR)

Items Winding changeover base shut-off timer Current limit timer after winding changeover Current limit value after winding changeover

Details

Setting range

Standard setting 150

Set the base shut-off time for contactor 50 to switching at winding changeover. 10000 Note that the contactor may be damaged with (ms) burning if the value of this parameter is too small. Set the current limit time to be taken after completion of contactor switching at winding changeover.

3260 SP060 MKT2 (PR)

0 to 10000 500 (ms)

3261 SP061 MKIL (PR)

Set the current limit value during a period 0 to 120 defined in SP060 (MKT2) after completion of (%) contactor switching at winding changeover. Not used. Set to "0". 0 0 to 1000 (s)

75

3262 SP062 3263 SP063 OLT (PR) 3264 SP064 OLL (PR)

0 60

Overload Set the time constant for detection of the alarm motor overload alarm. detection time

Overload Set the detection level of the motor overload 0 to 180 alarm alarm. (%) detection level Set the magnification of speed loop proportional gain with respect to SP022 (VGNP1) at the maximum motor speed defined in SP017 (TSP). Set the speed when the speed loop proportional gain change starts.
Proportional gain SP022 SP022 (SP065/100) SP066 SP017

110

3265 SP065 VCGN1 Target value (PR) of variable speed loop proportional gain 3266 SP066 VCSN1 (PR) Change starting speed of variable speed loop proportional gain

0 to 100 (%)

100

0 to 32767 0 (r/min)

Speed

3267 SP067 VIGWA (PR)

Change starting speed of variable current loop gain

Set the speed where the current loop gain change starts.

0 to 32767 0 (r/min)

3268 SP068 VIGWB (PR)

Change Set the speed where the current loop gain ending speed change ends. of variable current loop gain

0 to 32767 0 (r/min)

II - 300

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items Target value of variable current loop gain

Details Set the magnification of current loop gain (torque component and excitation component) for a change ending speed defined in SP068 (VIGWB). When this parameter is set to "0", the magnification is 1.
Gain SP069(1/16)-fold 1-fold Speed SP067 SP068 SP017

Setting range 0 to 32767 (1/16-fold)

Standard setting 0

3269 SP069 VIGN (PR)

SP017 (TSP) Maximum motor speed 0 to 6000 6001 to 8000 8001 or more

SP067 (VIGWA) 0 5000 5000

SP068 (VIGWB) 0 8000 10000

SP069 (VIGN) 0 45 64

3270 SP070 FHz

Machine resonance suppression filter frequency

When machine vibration occurs in speed and 0 to 3000 position control, set the frequency of the (Hz) required vibration suppression. Note that a value of 100Hz or more is set. Set to "0" when not used. Use not possible. Use not possible. 0 0

3271 SP071 3272 SP072 3273 SP073 3274 SP074 3275 SP075 3276 SP076 FONS Machine resonance suppression filter operation speed

0 0

When the vibration increases in motor stop (ex. in orientation stop) when the machine vibration suppression filter is operated by SP070, operate the machine vibration suppression filter at a speed of this parameter or more. When set to "0", this is validated for all speeds.

0 to 32767 (r/min)

3277 SP077 TDSL (PR) 3278 SP078 FPWM (PR) 3279 SP079 3280 SP080 SWTD 3281 SP081 3282 SP082 3283 SP083 to to 3286 SP086

Fixed control Set by Mitsubishi. constant Set "14" unless designated in particular. Fixed control Set by Mitsubishi. constant Set "1" unless designated in particular. Use not possible. Fixed control Set by Mitsubishi. constant Set "0" unless designated in particular. Use not possible. Use not possible. 1 0 0 0 0

14 1 0 0 0 0

II - 301

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items Target value of variable torque limit magnification at deceleration Speed for starting change of variable torque limit magnification at deceleration

Details

Setting range

Standard setting 75

3287 SP087 DIQM (PR)

Set the minimum value of variable torque limit 0 to 150 at deceleration. (%)

3288 SP088 DIQN (PR)

Set the speed where the torque limit value at deceleration starts to change.
Torque limit Inversely proportional to speed

0 to 32767 3000 (r/min)

100% SP087

Speed SP088 SP017

3289 SP089 3290 SP090 3291 SP091 3292 SP092 3293 SP093 ORE (PR) Tolerable pulse check error

Use not possible. Use not possible. Use not possible. Use not possible. Set this when detecting the pulse detector's pulse mistakes. (Valid only for full close control.)

0 0 0 0

0 0 0 0

0 to 32767 0

3294 SP094 LMAV Load meter (PR) output filter

Set the filter time constant of load meter 0 to 32767 0 output. (2ms) When "0" is set, a filter time constant is set to 100ms.

II - 302

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items Fixed control constant Encoder gear ratio

Details Set by Mitsubishi. Set "0" unless designated in particular. 0

Setting range

Standard setting 0

3295 SP095 VFAV (PR) 3296 SP096 EGAR (PR)

Set the gear ratio between the spindle end and 0 to 4 the encoder end (except for the motor-built-in encoder) as indicated below.
Setting value 0 1 2 3 4 Gear ratio (deceleration) 1:1 1:2 1:4 1:8 1 : 16

(Note) Use a combination so that the encoder end is slower than the spindle end. 3297 SP097 SPECO Orientation (PR) specification Set the orientation specifications in bit units.
F E ostp orze 7 vg8x 6 D C ksft gchg 5 fdir 4 osc1 B A ips2 9 8

0000 to FFFF HEX setting

0000

2 1 0 dmin odi2 odi1

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 0 odi1 Orientation rotation direction odi2 00: Previous (the direction in which the motor has so far rotated under speed control) 01: Forward rotation 1 10: Backward rotation 11: Prohibited (Same as setting value = 10) Orientation in-position 2 dmin Orientation in-position advance invalid advance valid 3 Indexing speed clamp 4 osc1 Indexing speed clamp invalid valid fdir Encoder detector Encoder detector 5 polarity: + polarity: 6 vg8x Speed gain *1/8 during Speed gain *1/8 during 7 torque limit valid torque limit invalid 8 9 A ips2 2nd in-position invalid 2nd in-position valid B C gchg Gain changeover during Gain changeover during orientation invalid orientation valid ksft Orientation virtual target Orientation virtual target D shift invalid shift valid E orze This is used by Mitsubishi. F ostp Set to "0" unless particularly designated.
In-position advance (bit 2) 0 (invalid) 0 (Invalid) Second in-position In-position signal in OINP width=1 Control output 4/ bit 4=1 Second in-position signal=0 Control output 4/ bit F=1 1 (valid) In-position signal in OINP width=1 Control output 4/ bit 4=1 Second in-position signal=0 Control output 4/ bit F=0 In-position signal in DINP width=1 Control output 4/ bit 4=1 Second in-position signal in OINP width = 0 Control output 4/ bit F=1

1 (Valid)

II - 303

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No. 3298 (PR)

Items SP098 VGOP Speed loop gain proportional term in orientation mode SP099 VGOI Orientation mode speed loop gain integral term

Details Set the speed loop proportional gain in orientation mode. When the gain is increased, rigidity is improved in the orientation stop but vibration and sound become larger. Set the speed loop integral gain in orientation mode.

Setting range 0 to 2000 (1/s)

Standard setting 63

3299 (PR)

0 to 2000 (0.1 1/s)

60

3300 (PR)

SP100 VGOD Orientation mode speed loop gain delay advance term SP101 DINP Orientation advance in-position width

Set a loop gain delay advance gain in 0 to 1000 orientation mode. (0.1 1/s) When this parameter is set to "0", PI control is applied. When using the orientation in-position advance function, set the in-position width that is larger than the normal in-position width defined in SP004 (OINP). 1 to 2880 (1/16)

15

3301 (PR)

16

3302 (PR)

SP102 OODR Excessive error Set the excessive error width in orientation value in mode. orientation mode SP103 FTM Index positioning completion OFF time timer Torque limit value for orientation servo locking

0 to 32767 32767 (1/4 pulse) (1 pulse= 0.088)

3303 (PR)

Set the time for forcedly turn OFF the index 0 to 10000 200 positioning completion signal (different from (ms) the orientation completion signal) after the leading edge of the indexing start signal. Set the torque limit value for orientation 0 to 120 in-position output. (%) If the external torque limit signal is input, the torque limit value set by this parameter is made invalid. 1 to 1000 (%) 100

3304 (PR)

SP104 TLOR

3305 (PR)

SP105 IQG0

Current loop Set the magnification for current loop gain gain magnifica- (torque component) at orientation tion 1 in completion. orientation mode Current loop Set the magnification for current loop gain gain magnifica- (excitation component) at orientation tion 2 in completion. orientation mode Deceleration rate 2 in orientation mode Deceleration rate 3 in orientation mode Deceleration rate 4 in orientation mode Set the deceleration rate in orientation mode corresponding to the gear 001. When this parameter is set to "0", same as SP006 (CSP). Set the deceleration rate in orientation mode corresponding to the gear 010. When this parameter is set to "0", same as SP006 (CSP). Set the deceleration rate in orientation mode corresponding to the gear 011. When this parameter is set to "0", same as SP006 (CSP). Use not possible.

100

3306 (PR)

SP106 IDG0

1 to 1000 (%)

100

3307

SP107 CSP2

0 to 1000

3308

SP108 CSP3

0 to 1000

3309

SP109 CSP4

0 to 1000

3310

SP110

II - 304

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No. 3311 3312 3313 3314 SP111 SP112 SP113

Items

Details Use not possible. Use not possible. Use not possible.

Setting range

Standard setting 0 0 0 0

SP114 OPER

Orientation pulse miss check value

An alarm "5C" will occur if the pulse 0 to 32767 miss value at the orientation stop (360/4096) exceeds this setting value. (Note that this is invalid when set to "0".) In this parameter, set the value to fulfill the following conditions. SP114 setting value > 1.5 SP004 (orientation in-position width) When the orientation clamp speed is changed by the control input, this parameter setting will be used instead of SP005: OSP. Indexing speed clamp valid This parameter is used when (SP097: SPEC0-bit4 = 1). Use not possible. 0 to 32767 (r/min)

3315

SP115 OSP2

Orientation motor speed clamp value 2

3316 3317 3318

SP116 SP117 ORUT SP118 ORCT

0 0 0

Set by Mitsubishi. 0 Set "0" unless designated in particular. Number of Set the number of times to retry when 0 to 100 orientation retry an orientation or feedback error occurs. (time) times The warning (A9) is issued while retrying orientation, and an alarm (5C) is issued when the set number of times is exceeded. Orientation position gain H winding compensation magnification Set the compensation magnification of 0 to 2560 the orientation position loop gain for the (1/256-fold) H winding. H winding orientation position loop gain = SP001 (or SP002) SP119/256 When set to "0", will become the same as SP001 or SP002.

3319

SP119 MPGH

3320

SP120 MPGL

Orientation position gain L winding compensation magnification

Set the compensation magnification of 0 to 2560 the orientation position loop gain for the (1/256-fold) L winding. L winding orientation position loop gain = SP001 (or SP002) SP120/256 When set to "0", will become the same as SP001 or SP002.

II - 305

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No. 3321

Items SP121 MPCSH Orientation deceleration rate H winding compensation magnification

Details

Setting range

Standard setting 0

Set the compensation magnification of 0 to 2560 the orientation deceleration rate for the (1/256-fold) H winding. Orientation deceleration rate for the H winding = SP006 SP121/256 When set to "0", will become the same as SP006.

3322

SP122 MPCSL Orientation deceleration rate L winding compensation magnification

Set the compensation magnification of 0 to 2560 the orientation deceleration rate for the (1/256-fold) L winding. Orientation deceleration rate for the L winding = SP006 SP122/256 When set to "0", will become the same as SP006.

3323 3324 3325

SP123 SP124 SP125

Use not possible. Use not possible. Use not possible.

0 0 0

0 0 0

II - 306

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items Orientation position gain M coil compensation

Details Set this to set the orientation position loop gain for the coil changeover motor to the M coil's unique value.

Setting range 0 to 2560 (1/256-fold)

Standard setting 0

3326 SP126 MPGH

3327 SP127 MPCSM Orientation Set this to set the orientation deceleration deceleration rate for the coil motor to the M coil's unique rate M coil value. compensation 3328 SP128 OXKPM Position loop gain magnification after orientation gain changeover (M coil) 3329 SP129 SPECC (PR) C-axis specifications Set the M coil gain magnification to be used after in-position when gain changeover is valid (SP097: SPEC0-bitC=1) during orientation.

0 to 2560 (1/256-fold)

0 to 2560 (1/256-fold)

Set the C-axis specifications in bit units.

F E D C B zrtn ptyp fb9x zrtd zrn2 7 vg8x 6 5 fdir 4 A 9 zdir 1 8 ztyp 0 fclx

0000

3 2 phos rtrn

(Note) Always set "0" for the empty bits.

bit Name Meaning when set to 0 Meaning when set to 1 fclx Closed loop Semi-closed loop 0 (Gear 1 : 1 only) 1 rtrn Position monitor during Position monitor during 2 ready OFF invalid ready OFF valid Vx4 synchronization 3 phos Normal (no compensation) compensation valid 4 fdir Position detector Position detector 5 polarity (+) polarity () 6 vg8x Speed gain 1/8 during Speed gain 1/8 during 7 torque limit valid torque limit invalid ztyp Z-phase type: Normal Z-phase type: Start up 8 start up only zdir Z-phase rising polarity Z-phase rising polarity 9 (+) () A B zrn2 This is used by Mitsubishi. C zrtd Set to "0" unless particularly designated. fb9x Speed feedback Speed feedback D Standard (PLG) 90,000 pulse detector ptyp Position control switch Position control switch E type: After zero point type: After deceleration return stop zrtn Zero point return Zero point return F direction: CCW direction: CW

3330 SP130 PGC1

First Set the position loop gain when the first gain 1 to 200 position is selected for C axis cutting. (1/s) loop gain for cutting on C-axis

15

II - 307

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No. 3331 SP131 PGC2

Items Second position loop gain for cutting on C-axis SP132 PGC3 Third position loop gain for cutting on C-axis SP133 PGC4 Stop position loop gain for cutting on C-axis SP134 VGCP0 C-axis non-cutting speed loop gain proportional item SP135 VGCI0 C-axis non-cutting speed loop gain integral item SP136 VGCD0 C-axis non-cutting speed loop gain delay advance item SP137 VGCP1 First speed loop gain proportional item for C-axis cutting SP138 VGCI1 First speed loop gain integral item for cutting on C-axis SP139 VGCD1 First speed loop gain delay advance item for cutting on C-axis SP140 VGCP2

Details Set the position loop gain when the second gain is selected for C axis cutting. Set the position loop gain when the third gain is selected for C-axis cutting. Set the position loop gain for stopping when carrying out C-axis cutting. Set the speed loop proportional gain in C-axis non-cutting mode.

Setting range 1 to 200 (1/s) 1 to 200 (1/s) 1 to 200 (1/s) 0 to 5000 (1/s)

Standard setting 15

3332

15

3333

15

3334 (PR)

63

3335 (PR)

Set the speed loop integral gain in C-axis non-cutting mode.

0 to 5000 (0.1 1/s)

60

3336 (PR)

Set the speed loop delay advance 0 to 5000 gain in C-axis non-cutting mode. (0.1 1/s) When this parameter is set to "0", PI control is exercised. Set the speed loop proportional gain 0 to 5000 when the first gain is selected for (1/s) C-axis cutting. Set the speed loop integral gain when the first gain is selected for C-axis cutting. 0 to 5000 (0.1 1/s)

15

3337 (PR)

63

3338 (PR)

60

3339 (PR)

3340 (PR)

Set the speed loop delay advance 0 to 5000 gain when the first gain is selected (0.1 1/s) for curing on the C-axis. When this parameter is set to "0", PI control is applied. Second speed Set the speed loop proportional gain 0 to 5000 loop gain when the second gain is selected for (1/s) proportional item C-axis cutting. for cutting on C-axis Second speed Set the speed loop integral gain 0 to 5000 loop gain integral when the second gain is selected for (0.1 1/s) item for cutting C-axis cutting. on C-axis

15

63

3341 (PR)

SP141 VGCI2

60

II - 308

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items

Details

Setting range

Standard setting 15

3342 SP142 VGCD2 Second speed (PR) loop gain delay advance item for cutting on C-axis

Set the speed loop delay advance gain 0 to 5000 when the second gain is selected for (0.1 1/s) C-axis cutting. When this parameter is set to "0", PI control is applied. 0 to 5000 (1/s)

3343 SP143 VGCP3 Third speed loop Set the speed loop proportional gain (PR) gain proportional when the third gain is selected for item for cutting C-axis cutting. on C-axis 3344 SP144 VGCI3 (PR) Third speed loop Set the speed loop integral gain when gain integral item the third gain is selected for C-axis for cutting on cutting. C-axis

63

0 to 5000 (0.1 1/s)

60

3345 SP145 VGCD3 Third speed loop (PR) gain delay advance item for cutting on C-axis

Set the speed loop delay advance gain 0 to 5000 when the third gain is selected for (0.1 1/s) C-axis cutting. When this parameter is set to "0", PI control is applied. 0 to 5000 (1/s)

15

3346 SP146 VGCP4 Speed loop gain Set the speed loop proportional gain (PR) proporwhen C-axis cutting is stopped. tional item for stop of cutting on C-axis 3347 SP147 VGCI4 (PR) Speed loop gain Set the speed loop integral gain when integral item for C-axis cutting is stopped. stop of cutting on C-axis

63

0 to 5000 (0.1 1/s)

60

3348 SP148 VGCD4 Speed loop gain (PR) delay advance item for stop of cutting on C-axis 3349 SP149 CZRN

Set the speed loop delay advance gain 0 to 5000 when C-axis cutting is stopped. (0.1 1/s) When this parameter is set to "0", PI control is applied. 1 to 500 (r/min)

15

C-axis zero point This parameter is valid when SP129 return speed (SPECC) bitE is set to "0". Set the zero point return speed used when the speed loop changes to the position loop.

50

3350 SP150 CPDT

C-axis zero point This parameter is valid when SP129 1 to 10000 return (SPECC) bitE is set to "0". deceleration point Set the deceleration rate where the machine starts to decelerate when it returns to the target stop point during C-axis zero point return. When the machine tends to overshoot at the stop point, set the smaller value.

II - 309

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items

Details

Setting range

Standard setting

3351 SP151 CPSTL

C-axis zero point This parameter is valid when SPECC return shift (SP129) bitE is set to "0". amount Set the C-axis zero point position. (low byte) C-axis zero point return shift amount (high byte) C-axis in-position Set the position error range in which width the in-position signal is output on the C-axis. Set the excessive error width on the C-axis.

HEX setting H: 0000 00000000 to L: 0000 FFFFFFFF (1/1000)

3352 SP152 CPSTH

3353 SP153 CINP

0000 to FFFF (1/1000) HEX setting

03E8

3354 SP154 CODRL Excessive error (PR) width on C-axis (low byte) 3355 SP155 CODRH Excessive error (PR) width on C-axis (high byte) 3356 SP156 OVSH

HEX setting H: 0001 00000000 to L: D4C0 FFFFFFFF (1/1000)

C-axis overshoot Set this to prevent overshooting when compensashifting from movement to stopping tion with C-axis control. (Set this referring to the load meter display when overshooting occurred.) Not used. Set to "0".

0 to 1000 (0.1%)

3357 SP157 to to 3358 SP158 3359 SP159 3360 SP160 3361 SP161 IQGC0 (PR)

Use not possible. Use not possible. Current loop gain Set the magnification of current loop magnifigain (torque component) for C-axis cation 1 for non-cutting. non-cutting on C-axis

0 0 1 to 1000 (%)

0 0 100

3362 SP162 IDGC0 (PR)

Current loop gain Set the magnification of current loop 1 to 1000 magnifigain (excitation component) for C-axis (%) cation 2 for non-cutting. non-cutting on C-axis Current loop gain Set the magnification of current loop magnifigain (torque component) for C-axis cation 1 for cutting. cutting on C-axis 1 to 1000 (%)

100

3363 SP163 IQGC1 (PR)

100

3364 SP164 IDGC1 (PR)

Current loop gain Set the magnification of current loop 1 to 1000 magnifigain (excitation component) for C-axis (%) cation 2 for cutting. cutting on C-axis

100

II - 310

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No. 3365

Items

Details

Setting range

Standard setting 0

SP165 PG2C C-axis position Set the second position loop gain when 0 to 999 loop gain 2 high-gain control is carried out for control (1/s) of the C-axis. This parameter is applied to all the operation modes of C-axis control. When this function is not used, assign "0". SP166 PG3C C-axis position Set the third position loop gain when 0 to 999 loop gain 3 high-gain control is carried out for control (1/s) of the C-axis. This parameter is applied to all the operation modes of C-axis control. When this function is not used, assign "0". SP167 PGU Position loop Set the position loop gain for when the gain for disturbance observer is valid. increased spindle holding force 0 to 100 (1/s)

3366

3367 (PR)

15

3368 (PR)

SP168 VGUP Speed loop Set the speed loop gain proportional item 0 to 5000 gain for when the disturbance observer is (1/s) proportional valid. item for increased spindle holding force SP169 VGUI Speed loop Set the speed loop gain integral item for gain integral when the disturbance observer is valid. item for increased spindle holding force 0 to 5000 (0.1 1/s)

63

3369 (PR)

60

3370 (PR)

SP170 VGUD Speed loop Set the speed loop gain delay advance 0 to 5000 gain delay item for when the disturbance observer is (0.1 1/s) advance item valid. for increased spindle holding force SP171 to SP176 Not used. Set to "0". 0

15

3371 to 3376

II - 311

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items

Details

Setting range

Standard setting 0000

3377 SP177 SPECS Spindle (PR) synchronous specifications

Set the spindle synchronous specifications in 0000 to FFFF bit units. HEX F E D C B A 9 8 setting odx8 phos
7 6 5 fdir 4 3 mach 2 1 0 fclx

bit Name Meaning when set to 0 0 fclx Closed loop 1 2 mach Automatic coil change3 over during spindle synchronization invalid 4 fdir Position detector direc5 tion (positive direction) 6 7 8 9 A B C odx8 Magnification of D excessive error width 8 times invalid E F (Used with SPJ)

Meaning when set to 1 Semi-closed loop

Automatic coil changeover during spindle synchronization valid Position detector direction (negative direction)

Magnification of excessive error width 8 times valid

3378 SP178 VGSP (PR)

Spindle synchronous speed loop gain proportional term Spindle synchronous speed loop gain integral term Spindle synchronous speed loop gain delay advance term Spindle synchronous Target value of variable speed loop proportional gain

Set the speed loop proportional gain in spindle synchronous mode.

0 to 2000 (1/s)

63

3379 SP179 VGSI (PR)

Set the speed loop integral gain in spindle synchronous mode.

0 to 2000 (0.1 1/s)

60

3380 SP180 VGSD (PR)

Set the speed loop delay advance gain in 0 to 1000 spindle synchronous mode. (0.1 1/s) When this parameter is set to "0", PI control is applied. Set the magnification of speed loop proportional gain with respect to SP178 (VGSP) at the maximum speed defined in SP017 (TSP) in spindle synchronous mode. 0 to 100 (%)

15

3381 SP181 VCGS (PR)

100

II - 312

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items

Details

Setting range

Standard setting

3382 SP182 VCSS (PR)

Spindle Set the speed when the speed loop synchronous proportional gain change starts in the Change spindle synchronous mode. starting speed of variable Proportional gain speed loop SP178 proportional gain SP178
(SP181/100) SP182 SP017 Speed

0 to 32767 0 (r/min)

3383 SP183 SYNV

Spindle synchronous Sync matching speed Spindle synchronous Acceleration rate feed forward gain Spindle synchronous In-position width Spindle synchronous Excessive error width Spindle synchronous Current loop gain magnification1 Spindle synchronous Current loop gain magnification 2 Spindle synchronous Position loop gain 2 Spindle synchronous Position loop gain 3

For changeover from the speed loop to the 0 to 1000 position loop in the spindle synchronous (r/min) mode, set a speed command error range for output of the synchronous speed matching signal. Set the acceleration rate feed forward gain 0 to 1000 in the spindle synchronous mode. (%) This parameter is used only with the SPJ2.

20

3384 SP184 FFCS (PR)

3385 SP185 SINP

Set the position error range for output of the 1 to 2880 in-position signal in the spindle (1/16) synchronous mode.

16

3386 SP186 SODR (PR)

Set the excessive error width in the spindle 1 to 32767 32767 synchronous mode. ( pulse) (1 pulse =0.088) Set the magnification of current loop gain (torque component) in the spindle synchronous mode. 1 to 1000 (%) 100

3387 SP187 IQGS (PR)

3388 SP188 IDGS (PR)

Set the magnification of current loop gain (excitation component) in the spindle synchronous mode.

1 to 1000 (%)

100

3389 SP189 PG2S

Set the second position loop gain when 0 to 999 high-gain control is carried out in the spindle (1/s) synchronous mode. When this parameter function is not used, set to "0". Set the third position loop gain when 0 to 999 high-gain control is carried out in the spindle (1/s) synchronous mode. When this parameter function is not used, set to "0". Use not possible. Not used. Set to "0". 0

3390 SP190 PG3S

3391 SP191 3392 SP192

II - 313

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items

Details

Setting range

Standard setting 0000

3393 SP193 SPECT Synchronized (PR) tapping specifications

Set the synchronized tapping specifications in 0000 to FFFF bit units. HEX F E D C B A 9 8 zrtn ptyp od8x phos setting
7 6 5 fdir 4 cdir 3 pyfx 2 rtrn 1 0 fclx

bit Name Meaning when set to 0 Meaning when set to 1 fclx Closed loop Semi-closed loop 0 (Gear 1 : 1 only) 1 rtrn Position monitor during Position monitor during 2 ready OFF invalid ready OFF valid 3 4 cdir Command polarity (+) Command polarity () Position detector fdir Position detector 5 polarity () polarity (+) 6 7 phos Normal Synchronized tapping (no compensation) position command 8 compensation (for synchronization with high-gain servo) 9 A B C od8x Magnification of Magnification of D excessive error width excessive error width 8 times invalid 8 times valid ptyp Position control switch Position control switch E type: After zero point type: After deceleration return stop zrtn Zero point return Zero point return F direction: CCW direction: CW

3394 SP194 VGTP (PR)

Synchronized tapping speed loop gain proportional term Synchronized tapping speed loop gain integral term Synchronized tapping speed loop gain delay advance term Synchronized tapping target value of variable speed loop proportional gain

Set the speed loop proportional gain in synchronized tapping mode.

0 to 2000 63 (1/s)

3395 SP195 VGTI (PR)

Set the speed loop integral gain in synchronized tapping mode.

0 to2000 60 (0.1 1/s)

3396 SP196 VGTD (PR)

Set the speed loop delay advance gain in 0 to 1000 15 synchronized tapping mode. (0.1 1/s) When this parameter is set to "0", PI control is applied.

3397 SP197 3398 SP198 VCGT (PR)

Use not possible.

0 100

Set the magnification of speed loop 0 to 100 proportional gain with respect to SP194 (%) (VGTP) at the maximum motor speed defined in SP017 (TSP) in synchronized tapping mode.

II - 314

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items

Details

Setting range

Standard setting

3399 SP199 VCST (PR)

Synchronized Set the speed where the speed loop tapping change proportional gain change starts during starting speed synchronized tapping. of variable speed loop Proportional gain proportional SP194 gain
SP194 (SP198/100) SP199 SP017 Speed

0 to 32767 0 (r/min)

3400 SP200 FFC1 (PR)

Synchronized tapping acceleration feed forward gain (gear 1) Synchronized tapping acceleration feed forward gain (gear 2) Synchronized tapping acceleration feed forward gain (gear 3) Synchronized tapping acceleration feed forward gain (gear 4) Fixed control constant

Set the acceleration feed forward gain for 0 to 1000 selection of gear 000 during synchronized (%) tapping. This parameter should be used when an error of relative position to Z-axis servo is large. Set the acceleration feed forward gain for selection of gear 001 during synchronized tapping. 0 to 1000 (%)

3401 SP201 FFC2 (PR)

3402 SP202 FFC3 (PR)

Set the acceleration feed forward gain for selection of gear 010 during synchronized tapping.

0 to 1000 (%)

3403 SP203 FFC4 (PR)

Set the acceleration feed forward gain for selection of gear 011 during synchronized tapping.

0 to 1000 (%)

3404 SP204 3405 SP205 3406 SP206 GCK

This is used by Mitsubishi. Set to "0" unless particularly designated.

0 0

Reverse run When the motor moves (including movement 0/1/2 detection error with external force), the motor overrun alarm detection width (3E) will be detected even if the speed command is 0 (including position control stop command) during servo ON (gate ON). Set the movement amount to be detected as an alarm. 0: Detect with 10 motor movement amount (Recommended setting) 1: Detect with 20 motor movement amount 2: Detect with 40 motor movement amount

II - 315

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No. 3407 SP207 GDL

Items Sequential mode startup timing

Details

Setting range

Standard setting 0

To carry out spindle synchronization or C-axis 0/1/2 control in the both-chuck state with no movement immediately after the power is turned ON, set this parameter so that the reverse run detection function will function correctly. Set so that servo ON timing for the opposing spindle has the combination of (1) and (2) shown in the drawing below. 0: Servo turns ON simultaneously with servo ON command, and servo ON status is returned immediately. 1: Gate turns ON at pattern (1) shown below, and servo ON status is returned two seconds later. 2: Gate turns ON at pattern (2) shown below, and servo ON status is returned two seconds later.
Servo ON command Servo ON (1) Servo ON (2) Servo ON status 2s Gate ON 700ms 300ms Gate ON 700ms 300ms

Servo ON

3408 SP208 W2 3409 SP209 to to 3413 SP213 3414 SP214 TZRN Synchronized tapping zero point return speed Synchronized tapping zero point return deceleration rate

This is used by Mitsubishi. Set to "0" unless particularly designated. Not used. Set to "0".

0 0

0 0

This parameter is valid when SP193 (SPECT) bitE is set to "0". Set the zero point return speed used when the speed loop changes to the position loop. This parameter is valid when SP193 (SPECT) 0 to 10000 1 bitE is set to "0". (pulse) Set the deceleration rate where the machine starts to decelerate when it returns to the target stop point during synchronized tapping zero point return. When the machine tends to overshoot at the stop point set a smaller value. This parameter is valid when SP193 (SPECT) 0 to 4095 bitE is set to "0". Set the synchronized tapping zero point position. Set the position error range for output of the in-position during synchronized tapping. 0

3415 SP215 TPDT

3416 SP216 TPST

Synchronized tapping zero point return shift amount Synchronized tapping in-position width

3417 SP217 TINP

1 to 2880 16 (1/16)

II - 316

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items

Details

Setting range 1 to 32767 (pulse) (1 pulse =0.088) 1 to 1000 (%)

Standard setting 32767

3418 SP218 TODR (PR)

Synchronized Set the excessive error width during tapping synchronized tapping. excessive error width Synchronized Set the magnification of current loop gain tapping current (torque component) during synchronized loop gain tapping. magnification 1 Synchronized Set the magnification of current loop gain tapping current (excitation component) during loop gain synchronized tapping. magnification 2 Synchronized tapping position loop gain 2 Synchronized tapping position loop gain 3 Set the second position loop gain when high-gain control is applied during synchronized tapping. When this parameter is not used, set to "0". Set the third position loop gain when high-gain control is applied during synchronized tapping. When this parameter is not used, set to "0".

3419 SP219 IQGT (PR)

100

3420 SP220 IDGT (PR)

1 to 1000 (%)

100

3421 SP221 PG2T

0 to 999 (1/s)

3422 SP222 PG3T

0 to 999 (1/s)

3423 SP223 SPDV

Speed monitor Set the spindle limit speed in the door speed open state. (Invalid when 0 is set.) If the spindle end speed exceeds this setting value when the door is open, the speed monitor error (5E) will occur.

0 to 800 (r/min)

3424 SP224 SPDF

Speed monitor Set the time (continuous) to detect alarms. 0 to 2813 time (Detected instantly when 0 is set.) (3.5ms) If gain changeover is valid (SP097: 0 to 2560 SPEC0-bitC=1) during orientation, set the (1/256-fold) magnification of each gain changed to after in-position.

0 0

3425 SP225 OXKPH Position loop gain magnification after orientation gain changeover (H coil) 3426 SP226 OXKPL Position loop gain magnification after orientation gain changeover (L coil) 3427 SP227 OXVKP Speed loop proportional gain magnification after orientation gain changeover

0 to 2560 (1/256-fold)

0 to 2560 (1/256-fold)

II - 317

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No.

Items Speed loop cumulative gain magnification after orientation gain changeover

Details

Setting range

Standard setting 0

3428 SP228 OXVKI

If gain changeover is valid (SP097: 0 to 2560 SPEC0-bitC=1) during orientation, set the (1/256-fold) magnification of each gain changed to after in-position.

3429 SP229 OXSFT Orientation virtual target shift amount 3430 SP230 3431 SP231 3432 SP232 3433 SP233 JL (PR) Disturbance observer general inertia scale

Set the amount to shift the target position when orientation virtual target position is valid (SP097: SPEC0-bitD=1). Use not possible.

0 to 2048 (360/4096)

Set the ratio of the motor inertia + load inertia and motor inertia.
Setting Motor inertia + load inertia 100 value = Motor inertia

0 to 5000 (%)

(Normally, set "100" or more. When less than "50" is set, the setting will be invalid.) To calculate speed loop gain with general inertia scale: The effective proportional gain and effective cumulative gain during the speed control are changed at the set scale. 3434 SP234 OBS1 (PR) Disturbance observer low path filter frequency Set the frequency of the low path filter for when the disturbance observer is valid. Setting (1/s) = 2f f: Approx. 1.5 times the disturbance frequency Set the gain for the disturbance observer. 0 to 500 (%) 0 This is used by Mitsubishi. Set to "0" unless particularly designated. This is used by Mitsubishi. Set to "0" unless particularly designated. 0 0 0 0 0 to 1000 (1/s) 0

3435 SP235 OBS2 (PR) 3436 SP236 OBS3 3437 SP237 KSCP 3438 SP238 SEZR 3439 SP239 SEZT 3440 SP240 3441 SP241 3442 SP242 Vavx 3443 SP243 UTTM 3444 SP244 OPLP 3445 SP245 PGHS 3446 SP246 TEST 3447 SP247 to to 3448 SP248

Disturbance observer gain Fixed control constant Fixed control constant

Use not possible. Use not possible. This is used by Mitsubishi. Set to "0" unless particularly designated. Use not possible. This is used by Mitsubishi. Set to "0" unless particularly designated. Use not possible.

0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0

II - 318

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No. 3449 SP249 SM0

Items Speed meter speed

Details

Setting range

Standard setting 0

Set the motor rotation speed when the 0 to 32767 speed meter 10V is output. (r/min) When set to "0", this parameter becomes the same as SP017 (TSP). Set the voltage when the load meter 120% 0 to 10 is output. When set to "0", this becomes (V) 10V. Use not possible. 0

3450 SP250 LM0

Load meter voltage

3451 SP251 to to 3452 SP252 3453 SP253 DA1NO D/A output channel 1 data number

Set the output data number for channel 1 32768 to of the D/A output function. 32767 When set to "0", the output is speedometer. Refer to "9.4 (1) For D/A output functions". Set the output data number for channel 2 32768 to of the D/A output function. 32767 When set to "0", the output is load meter. Refer to "9.4 (1) For D/A output functions". Set the data magnification for channel 1 of 32768 to the D/A output function. 32767 The output magnification is the setting (1/256-fold) value divided by 256. When set to "0", the output magnification becomes 1-fold, in the same manner as when "256" is set. Refer to "9.4 (1) For D/A output functions". Set the data magnification for channel 2 of 32768 to the D/A output function. 32767 The output magnification is the setting (1/256-fold) value divided by 256. When set to "0", the output magnification becomes 1-fold, in the same manner as when "256" is set. Refer to "9.4 (1) For D/A output functions".

3454 SP254 DA2NO

D/A output channel 2 data number

3455 SP255 DA1MPY DA output channel 1 magnification

3456 SP256 DA2MPY DA output channel 2 magnification

II - 319

9. 9.3

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SPINDLE PARAMETERS

No. 3457 SP257 RPM (PR) to to SP320 BSD 3520 (PR)

Items Motor constant (H coil)

Details This parameter is valid only in the following two conditional cases: (c) In case that SP034 (SFNC2) bit0=1 and SP034 (SFNC2) bit2=0 Set the motor constants when using a special motor, not described in the SP040 (MTYP) explanation and when not using the coil changeover motor. (d) In case that SP034 (SFNC2) bit0=1 and SP034 (SFNC2) bit2=1 Set the motor constant of the H coil of the coil changeover motor. (Note) It is not allowed for the user to change the setting.

Setting range 0000 to FFFF HEX setting

Standard setting 0000

3521 SP321 RPML (PR) to to SP384 BSDL 3584 (PR)

Motor constant (L coil)

This parameter is valid only in the following conditional case: (b) In case that SP034 (SFNC2) bit0=1 and SP034 (SFNC2) bit2=1 Set the motor constant of the L coil of the coil changeover motor. (Note) It is not allowed for the user to change the setting.

0000 to FFFF HEX setting

0000

II - 320

9. 9.4

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SUPPLEMENTARY EXPLANATION

9.4 MDS-C1-SP SUPPLEMENTARY EXPLANATION

(1) For D/A output functions (i) Outline The D/A output function is mounted in the standard system in the MDS-C1-SP. Using this D/A output function, the drive unit status and each data can be confirmed. (ii) Hardware specifications 2 channels 8 bit 0 to +10V Output pin CH 1: CN9-9 pin CH 2: CN9-19 pin GND: CN9-1.11 pin (iii) Parameters Set the data No. and output magnification of each channel according to the parameters below. Name SP253 SP254 SP255 SP256 Details D/A output channel 1 data No. D/A output channel 2 data No. D/A output channel 1 data magnification D/A output channel 2 data magnification

(iv) Output data No. Set the No. of the data to be output in SP253 and SP254. A correlation of the output data and the data No. is shown below. No. (setting value) 0 2 CH1 Output data Speedometer output Current command Units Maximum speed at 10V CH2 Output data Load meter output Units 120% load at 10V

4 6 7

8 9 10 11

12 13

80 81 82 83 84 85 86 87

When the actual data is 4096, the current command data is regarded as 100%. Current feedback When the actual data is 4096, the current feedback data is regarded as 100%. Speed feedback Actual data r/min Position droop low-order Interpolation units when the actual data is 23040000, Position droop high-order the position droop data is regarded as 360. Position F T low-order Interpolation units/NC communication cycle Position F T high-order Position command low-order Interpolation units when the actual data is 23040000, Position command the position command data is high-order regarded as 360. Feedback position low-order Interpolation units when the actual data is 23040000, Feedback position the feedback position data is high-order regarded as 360. Bit correspondence Control input 1 Control input 2 Control input 3 Control input 4 Bit correspondence Control output 1 Control output 2 Control output 3 Control output 4

Same as CH1

(Note) The % of the current command and current feedback indicate 30min. rating = 100%. II - 321

9. 9.4

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SUPPLEMENTARY EXPLANATION

(v) Setting the output magnification Set the output magnification in SP255 and SP256. Data = actual data

SP255 or SP256 256

Using the expression above, (a) Output data other than speedometer output and load meter output carries out the D/A output in Fig. 1. (b) Speedometer output data and load meter output data carries out the D/A output in Fig. 2. D/A output voltage D/A output voltage

+10V

+10V

+5V

+5V

0V 128

+127

DATA

0V 0 +127 +255

DATA

Fig. 1

Fig. 2

(Example 1) Current command, current feedback The data is regarded as 100% when the actual data = 4096. Therefore, for example, the actual data is output as shown below during +120% current feedback. Actual data = 4096 1.2 = 4915 If "256" is set (magnification 1) in parameter SP255 (SP256), from Fig.1, the D/A output voltage will be as shown below, exceeding the D/A output voltage maximum value. 5V + {4915 1 (5V/128)} = 197V > 10V Therefore, if (for example) "6" is set in parameter SP255 (SP256), the D/A output voltage will become as shown below, and data confirmation will be possible. 5V + {4915 6/256 (5V/128)} = 9.5V < 10V

II - 322

9. 9.4

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SUPPLEMENTARY EXPLANATION

(Example 2) Speed feedback Data unit is r/min. Therefore, at (for example) +2000r/min, the motor speed will be output as "2000". If "256" is set (magnification 1) in parameter SP255 (SP256), from Fig.1, the D/A output voltage will be as shown below, exceeding the D/A output voltage maximum value. 5V + {2000 x 1 x (5V/128)} = 83.125V > 10V Therefore, if (for example) "16" is set in parameter SP255 (SP256), the D/A output voltage will become as shown below, and data confirmation will be possible. 5V + {2000 x 16/256 x (5V/128)} = 9.88V < 10V (Example 3) Position droop The data unit is r/min. Data is regarded as 100% when the actual data = 4096. Therefore, for example, the actual data is output as shown below during the +0.1 position droop. Actual data = 0.1 x 23040000/360 = 6400 If "256" is set (magnification 1) in parameter SP255 (SP256), from Fig.1, the D/A output voltage will be as shown below, exceeding the D/A output voltage maximum value. 5V + {6400 x 1 x (5V/128)} = 255V > 10V Therefore, if (for example) "5" is set in parameter SP255 (SP256), the D/A output voltage will become as shown below, and data confirmation will be possible. 5V + {2000 x 5/256 x (5V/128)} = 9.88V < 10V (Example 4) Confirm the orientation complete signal (ORCF) with the control output 4L. The data unit is bit corresponding data. Refer to the Instruction Manual for the meanings of the control output 4L bit corresponding signals. The orientation complete signal (ORCF) corresponds to the control output 4L/bit 4. Therefore, for example, the actual data is output as shown below when ORCF= ON. bit 4 corresponding actual data = 24 = 16 If "256" is set (magnification 1) in parameter SP255 (SP256), from Fig.1, the D/A output voltage will be as shown below, and data confirmation will be possible. 5V + {16 x 1 x (5V/128)} = 5.625V < 10V Note that, if a bit other than bit4 is ON, the current of that bit will be added to the 6.25V shown above, and at the actual ORCF signal measurement will be as shown below, so confirm the changed voltage. (5.625 V 5V) = 0.625 V

II - 323

9. 9.4

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SP SUPPLEMENTARY EXPLANATION

(2) Power supply type Set "ptyp" of SP041 (PTYP) from the following table. When an external emergency stop is valid No. 0xkW 0x 1xkW 1x CV-110 CV-220 CV-37 CV-150 CV-260 CV-370 CV-75 CV-185 CV-75 CV-185 CV-37 CV-150 CV-260 CV-370 CR-75 CR-90 CR-55 2xkW 2x 3xkW 3x CV-300 4xkW 4x 5xkW 5x CV-110 CV-220 6xkW 6x 7xkW 7x CV-300 Resistance regeneration 8xkW 8x CR-10 CR-15 CR-22 CR-37

1 2 3 4 5 6 7 8 9 A B C D E F

(3) Regenerative resistance type Set "rtyp" of SP041 (PTYP) from the following table. No. 0 1 2 3 4 5 6 7 8 9 A B C D E F Regenerative resistance type GZG200W260HMJ GZG300W130HMJ x 2 MR-RB30 MR-RB50 GZG200W200HMJ x 3 GZG300W200HMJ x 3 R-UNIT-1 R-UNIT-2 R-UNIT-3 Resistance value() 26 26 13 13 6.7 6.7 30 15 15 Watts(W) 80 150 300 500 350 500 700 700 2100

II - 324

9. 9.5

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SUPPLEMENTARY EXPLANATION

9.5 MDS-C1-SPM SUPPLEMENTARY EXPLANATION

(1) For D/A output functions (i) Outline The D/A output function is mounted in the standard system in the MDS-C1-SPM. Using this D/A output function, the drive unit status and each data can be confirmed. (ii) Hardware specifications 2 channels 8 bit 0 to +10V Output pin CH 1: CN9-9 pin CH 2: CN9-19 pin GND: CN9-1.11 pin (iii) Parameters Set the data No. and output magnification of each channel according to the parameters below. Name SP253 SP254 SP255 SP256 Details D/A output channel 1 data No. D/A output channel 2 data No. D/A output channel 1 data magnification D/A output channel 2 data magnification

(iv) Output data No. Set the No. of the data to be output in SP253 and SP254. A correlation of the output data and the data No. is shown below. No. (setting value) 0 2 CH1 Output data Speedometer output Current command Units Maximum speed at 10V CH2 Output data Load meter output Units 120% load at 10V

When the actual data is 4096, the current command data is regarded as 100%. 3 Current feedback When the actual data is 4096, the current feedback data is regarded as 100%. 4 Speed feedback Actual data r/min 6 Position droop low-order Interpolation units when the actual data is 23040000, 7 Position droop high-order the position droop data is regarded as 360. 8 Position F T low-order Interpolation units/NC communication cycle 9 Position F T high-order 10 Position command low-order Interpolation units when the actual data is 23040000, 11 Position command Same as CH1 the position command data is high-order regarded as 360. 12 Feedback position low-order Interpolation units when the actual data is 23040000, 13 Feedback position the feedback position data is high-order regarded as 360. Bit correspondence 80 Control input 1 81 Control input 2 82 Control input 3 83 Control input 4 Bit correspondence 84 Control output 1 85 Control output 2 86 Control output 3 87 Control output 4 (Note) The % of the current command and current feedback indicate 30min. rating = 100%.

II - 325

9. 9.5

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SUPPLEMENTARY EXPLANATION

(vi) Setting the output magnification Set the output magnification in SP255 and SP256. Data = actual data

SP255 or SP256 256

Using the expression above, (a) Output data other than speedometer output and load meter output carries out the D/A output in Fig. 1. (b) Speedometer output data and load meter output data carries out the D/A output in Fig. 2. D/A output voltage D/A output voltage

+10V

+10V

+5V

+5V

0V 128

+127

DATA

0V 0 +127 +255

DATA

Fig. 1

Fig. 2

(Example 1) Current command, current feedback The data is regarded as 100% when the actual data = 4096. Therefore, for example, the actual data is output as shown below during +120% current feedback. Actual data = 4096 1.2 = 4915 If "256" is set (magnification 1) in parameter SP255 (SP256), from Fig.1, the D/A output voltage will be as shown below, exceeding the D/A output voltage maximum value. 5V + {4915 1 (5V/128)} = 197V > 10V Therefore, if (for example) "6" is set in parameter SP255 (SP256), the D/A output voltage will become as shown below, and data confirmation will be possible. 5V + {4915 6/256 (5V/128)} = 9.5V < 10V

II - 326

9. 9.5

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SUPPLEMENTARY EXPLANATION

(Example 2) Speed feedback Data unit is r/min. Therefore, at (for example) +2000r/min, the motor speed will be output as "2000". If "256" is set (magnification 1) in parameter SP255 (SP256), from Fig.1, the D/A output voltage will be as shown below, exceeding the D/A output voltage maximum value. 5V + {2000 x 1 x (5V/128)} = 83.125V > 10V Therefore, if (for example) "16" is set in parameter SP255 (SP256), the D/A output voltage will become as shown below, and data confirmation will be possible. 5V + {2000 x 16/256 x (5V/128)} = 9.88V < 10V (Example 3) Position droop The data unit is r/min. Data is regarded as 100% when the actual data = 4096. Therefore, for example, the actual data is output as shown below during the +0.1 position droop. Actual data = 0.1 x 23040000/360 = 6400 If "256" is set (magnification 1) in parameter SP255 (SP256), from Fig.1, the D/A output voltage will be as shown below, exceeding the D/A output voltage maximum value. 5V + {6400 x 1 x (5V/128)} = 255V > 10V Therefore, if (for example) "5" is set in parameter SP255 (SP256), the D/A output voltage will become as shown below, and data confirmation will be possible. 5V + {2000 x 5/256 x (5V/128)} = 9.88V < 10V (Example 4) Confirm the orientation complete signal (ORCF) with the control output 4L. The data unit is bit corresponding data. Refer to the Instruction Manual for the meanings of the control output 4L bit corresponding signals. The orientation complete signal (ORCF) corresponds to the control output 4L/bit 4. Therefore, for example, the actual data is output as shown below when ORCF= ON. bit 4 corresponding actual data = 24 = 16 If "256" is set (magnification 1) in parameter SP255 (SP256), from Fig.1, the D/A output voltage will be as shown below, and data confirmation will be possible. 5V + {16 x 1 x (5V/128)} = 5.625V < 10V Note that, if a bit other than bit4 is ON, the current of that bit will be added to the 6.25V shown above, and at the actual ORCF signal measurement will be as shown below, so confirm the changed voltage. (5.625 V 5V) = 0.625 V

II - 327

9. 9.5

MDS-C1-SP, SPM SPINDLE PARAMETERS MDS-C1-SPM SUPPLEMENTARY EXPLANATION

(2) Power supply type Set "ptyp" of SP041 (PTYP) from the following table. When an external emergency stop is valid No. 0 1 2 3 4 5 6 7 8 9 A B C D E F 0xkW 1xkW 0x 1x PS not connected CV-110 2xkW 2x 3xkW 3x CV-300 4xkW 4x 5xkW 5x 6xkW 6x 7xkW 7x CV-300 Resistance regeneration 8xkW 8x

CV-110 CV-220 CV-220 CV-37

CV-37 CV-150 CV-260 CV-370 CV-75 CV-185

CR-10 CR-15 CR-22 CR-37 CR-55 CV-370 CR-75 CR-90

CV-150 CV-260 CV-75 CV-185

(3) Regenerative resistance type Set "rtyp" of SP041 (PTYP) from the following table. No. 0 1 2 3 4 5 6 7 8 9 A B C D E F Regenerative resistance type Resistance value() Watts(W)

Large capacity + ready ON high-speed sequence Ready ON high-speed sequence

II - 328

10.

MACHINE ERROR COMPENSATION 10.1 FUNCTION OUTLINE

10. MACHINE ERROR COMPENSATION

10.1 FUNCTION OUTLINE

Machine error compensation includes two independent functions: memorized pitch error compensation and memorized relative position compensation. (1) Memorized pitch error compensation According to the specified parameters this method compensates an axis feed error caused by a ball screw pitch error etc. With the reference point defined as the base set the compensation amount in the division points obtained by equally dividing the machine coordinates. (See Fig. 1. 1) The compensation amount can be set by either the absolute or incremental system. Select the desired method with the #4000:Pinc. Machine position is compensated between division points n and n+1 as much as compensation amount between them by linear approximation.

Fig. 1. 1 Relationship between the compensation amount and machine position

II - 329

10.

MACHINE ERROR COMPENSATION 10.1 FUNCTION OUTLINE

(2) Memorized relative position compensation This method according to the parameters specified in advance compensates the relative position error between two orthogonal axes caused by deflection of the moving stand. For this as shown in Fig. 1. 2 specify the compensation amount in the compensation axis direction in the division points obtained by equally dividing the machine coordinates of the base axis. The base axis is one of the two orthogonal axes to which relative position compensation applies. This axis is used as the criterion for relative-error measurement. The compensation axis is the coordinate axis that is orthogonal to the base axis. The compensation is actually made for this coordinate axis. The section between division points n and n+1 is compensated smoothly by linear approximation.

Actual machine position of compensation axis

Actual machine position for which no compensation is made

: Division points

Command machine position along base axis Reference point n n+1 n+2 Command machine position

Compensation amount between division points Compensation amount

Fig. 1. 2 Relationship between base and compensation axes

II - 330

10.

MACHINE ERROR COMPENSATION 10.1 FUNCTION OUTLINE

(SETUP PARAM 5. 1/15) # 4000 (PR) Pinc Item Machine error offset increment method Details Specify whether to use the incremental amount method or absolute amount method when setting the machine error compensation data. Setting range 0: Absolute volume method 1: Incremental volume method

<1st axis> # 4001 cmpax Item Basic axis Details Specify the basic axis address for machine error compensation. 1) For pitch error compensation set the name of the axis to be compensated. 2) For relative position compensation set the name of the axis to be the base axis. Set as the "system No. + axis name" when using the multi-system. (Example) Z axis for 2nd system: 2Z Set the compensation axis address for machine error compensation. 1) For pitch error compensation set the same axis name as #4001 cmpax. 2) For relative position compensation set the name of the axis to be actually compensated. Set as the "system No. + axis name" when using the multi-system. (Example) Z axis for 2nd system: 2Z Set the compensation data No. corresponding to the reference point position. The reference point is actually the base so there is no compensation No. Set the number that is decremented by 1. Set the compensation data No. that is on the farthest negative side. Setting range X, Y, Z, U, V, W, A, B, or C axis address

4002

drcax

Compensation axis

X, Y, Z, U, V, W, A, B, or C axis address

4003

rdvno

Division point number at reference point position Division point number at the most negative side Division point number at the most positive side Compensation scale factor Division interval

4101 to 5124

4004

mdvno

4101 to 5124

4005

pdvno

Set the compensation data No. that is on the farthest positive side. Set the compensation amounts scale. Set the interval to divide the basic axis. Each compensation data will be the compensation amount for each of these intervals.

4101 to 5124

4006 4007

sc spcdv

0 to 99 1 to 9999999

II - 331

10.

MACHINE ERROR COMPENSATION 10.1 FUNCTION OUTLINE

<2nd axis> 4011 4012 4013 4014 4015 4016 4017

<3rd axis> 4021 4022 4023 4024 4025 4026 4027

<4th axis> 4031 4032 4033 4034 4035 4036 4037

<5th axis> 4041 4042 4043 4044 4045 4046 4047

<6th axis> 4051 4052 4053 4054 4055 4056 4057

<7th axis> 4061 4062 4063 4064 4065 4066 4067

<8th axis> 4071 4072 4073 4074 4075 4076 4077

<9th axis> 4081 4082 4083 4084 4085 4086 4087

<10th axis> 4091 4092 4093 4094 4095 4096 4097

Set the parameters corresponding to the 1st axis parameters 4001 to 4007 for each axis. A maximum of 6 axes can be controlled but as the relative position is compensated settings for 10 axes can be made.

(SETUP PARAM 5. 3/15) to (SETUP PARAM 5. 15/15) # 4101 Item Details Set the compensation amount for each axis. Setting range 128 to 127 The actual compensation amount will be the value obtained by multiplying the setting value with the compensation scale.

5124

II - 332

10. 10.2

MACHINE ERROR COMPENSATION SETTING COMPENSATION DATA

10.2 SETTING COMPENSATION DATA

Compensation data can be set according to either absolute or incremental system. "#4000:Pinc" 0: Absolute system 1: Incremental system (1) Absolute system Feed from the reference point to each division point is executed as shown in Fig. 2. 1. The following is obtained at this time. Set it as the compensation amount. (Specified position Real machine position) 2 (Unit of output) For example assume that the feed from the reference point to the +100mm position is executed. Also assume that the real machine position is 99.990mm. In this case the following value is defined as the compensation amount used at the +100mm position: (100000 99990) 2 = 20 pulses The resultant value is defined as the compensation amount. Assume that the real machine position resulting when feed to the 100mm position is executed is 99.990mm. In this case the following value is defined as the compensation amount used at the 100mm position: (100000 (99990)) 2 = 20 pulses
-100 Compensation amount: 20 pulses (-10m) +99.990 Compensation amount: -20 pulses (10m) +100

-99.990

Fig. 2. 1 (2) Incremental system Fig. 2. 2 contains a machine position that is placed in the positive direction with respect to the reference point. Assume that feed from division n1 to n (division interval) is executed. In this case the following value is defined as the compensation amount: (Division interval Actual movement distance) 2 (Unit of output)

II - 333

10. 10.2

MACHINE ERROR COMPENSATION SETTING COMPENSATION DATA

(3) Fig. 2. 3 contains a machine position that is placed in the negative direction with respect to the reference point. Assume that feed from division point n+1 to n by the division interval is executed. In this case the following value is defined as the compensation amount: (Division interval + Actual movement distance) 2 (Unit of output)
1 n n+1

n: Division point compensation number 1: Division interval

n-1 1

Fig. 2. 2 Unit Range : Unit of output : 128 to 127

Fig. 2. 3

(Note) The unit of output is used as the unit of setting. The actual unit of compensation pulses depends on the compensation scale factor.

II - 334

10.3

10. MACHINE ERROR COMPENSATION EXAMPLE IN USING A LINEAR AXIS AS THE BASE AXIS

10.3 EXAMPLE IN USING A LINEAR AXIS AS THE BASE AXIS

(1) When "mdvno" or "pdvno" exists at both ends of "rdvno":
Compensation amount in incremental system

(1) #4102

(3) #4103

(-3) Error 3 2 1

(-2) #4104

(0) #4105

(3) #4106

#4101

-1 -2 -3 (3)
Compensation amount in absolute system

Base axis machine coordinate

(-2) (-2) (1)

(0) (-1)

Division point number #4101 #4102 #4103 #4104 #4105 #4106 Specified machine position 300.000 200.000 100.000 100.000 200.000 300.000 Real machine position 299.999 200.000 100.003 100.002 200.002 299.999 Compensation amount Increment al Absolute 2 2 6 0 6 6 4 4 0 4 6 2

rdvno mdvno pdvno

4103 4101 4106

If the setting range (mdvno to "pdvno") is exceeded the compensation will be based on compensation amount at mdvno or "pdvno".

II - 335

10.3

10. MACHINE ERROR COMPENSATION EXAMPLE IN USING A LINEAR AXIS AS THE BASE AXIS

(2) When the range compensated is only the positive range:

Compensation amount in incremental system Error

(-2) #4113

(1) #4114

(0) #4115

(3) #4116

(1) #4117

3 2 1

-1 -2 -3 (-2)
Compensation amount in absolute system

Base axis machine coordinate

(-1) (-1) (2) (3)

Division point number Compensati Incremen on tal amount Absolute

#4113 4 4

#4114 2 2

#4115 0 2

#4116 6 4

#4117 2 6

rdvno mdvno pdvno

4112 4113 4117

If the machine position exceeds "pdvno" the compensation will be based on the compensation amount at "pdvno". If the machine position is negative in this case no compensation will be executed.

II - 336

10.3

10. MACHINE ERROR COMPENSATION EXAMPLE IN USING A LINEAR AXIS AS THE BASE AXIS

(3) When the range compensated is only the negative range:

Compensation amount in incremental system

(-1) #4126

(1) #4127

(3) #4128

(1) #4129

(0) #4130

(-3) Error 3 2 1

#4125

Base axis machine coordinate

-1 -2 -3 (3) (3) (2) (-1)

Compensation amount in absolute system

(-2) (-1)

Division point number Compensati Incremen on amount tal Absolute

#4125 2 2

#4126 2 4

#4127 6 2

#4128 2 4

#4129 0 6

#4130 6 6

rdvno 4130 mdvno 4125 pdvno 4130

If the machine position exceeds "mdvno" the compensation will be based on compensation amount at "mdvno".

II - 337

10.3

10. MACHINE ERROR COMPENSATION EXAMPLE IN USING A LINEAR AXIS AS THE BASE AXIS

(4) When compensation is executed in a range that contains no reference point:

Compensation amount in incremental system

(-1)

(-1) #4138

(3) #4139

(1) #4140

Error

3 2 1

#4135

#4136

#4137

-1 -2 -3
Compensation amount in absolute system

Base axis machine coordinate

(-1) (-2) (1) (2)

Division point number Compensati Incremen on amount tal Absolute

#4135

#4136

#4137 2 2

#4138 2 4

#4139 6 2

#4140 2 4

rdvno 4134 mdvno 4136 pdvno 4140

In this case the compensation is executed in the range from "mdvno" to "pdvno". This setting rule applies also when the compensation is executed in a range which contains negative machine positions and no reference point.

II - 338

10.4

10. MACHINE ERROR COMPENSATION EXAMPLE IN USING A ROTATION AXIS AS THE BASE AXIS

10.4 EXAMPLE IN USING A ROTATION AXIS AS THE BASE AXIS

Compensation amount in incremental system Error

(-2) #4123

(1) #4124

(0) #4125

(3) #4126

(1) #4127

(-3) #4128

3 2 1

360 -1 -2 -3 (-2) (-1)

Compensation amount in absolute system Base axis machine coordinate

(-1) (2) (3) (0)

Division point number Compensati Incremen on tal amount Absolute

#4123 4 4

#4124 2 2

#4125 0 2

#4126 6 4

#4127 2 6

#4128 6 0

rdvno 4122 mdvno 4123 pdvno 4128

In this case the sum of the compensation amounts set according to the incremental system is always "0". For the absolute system the compensation amount at the terminal point (360 degrees) is always "0".

II - 339

11. 11.1

PLC CONSTANTS PLC TIMER

11. PLC CONSTANTS

11.1 PLC TIMER

(SETUP PARAM 6. 1/14) to (SETUP PARAM 6. 2/14) # 6000 PLC device T000 Item 10ms adding timer <10ms> Details Set the time for the timer used in the PLC program (ladder). (Note) This setting value is valid when parameter "#6449 bit0" in the following "[BIT SELECT]" is set to "0". Set the time for the timer used in the PLC program (ladder). (Note) This setting value is valid when parameter "#6449 bit0" in the following "[BIT SELECT]" is set to "0". Set the time for the timer used in the PLC program (ladder). (Note) This setting value is valid when parameter "#6449 bit0" in the following "[BIT SELECT]" is set to "0". Setting range 0 to 32767 (10ms)

6015 6016

T015 T016

100ms adding timer <10ms>

0 to 32767 (100ms)

6095 6096

T095 T096

100ms cumulative timer <100ms INC>

0 to 32767 (100ms)

6103

T103

(SETUP PARAM 6. 10/14) to (SETUP PARAM 6. 14/14) # 6600 PLC device R1200/bit0 R1250/bit0 Item PLC timer expansion Details Set the time for the expanded PLC timer This is set for the timer coils: R1200 to R1224, and timer contacts: R1250 to R1274. A timer command can be issued to a contact other than the existing timer contacts (T0 to T103, Q0 to Q151). Setting range 0 to 32767 (10ms)

6999

R1224/bitF R1274/bitF

10ms adding timer <10ms>

11.2 PLC COUNTER

(SETUP PARAM 6. 3/14) # 6200 PLC device C000 Item Counter Details Set the time for the counter used in the PLC program (ladder). (Note) This setting value is valid when parameter "#6449 bit1" in the following "[BIT SELECT]" is set to "0". Setting range 0 to 32767

6223

C023

II - 340

11. 11.3

PLC CONSTANTS PLC CONSTANTS

11.3 PLC CONSTANTS

(SETUP PARAM 6. 4/14) # 6301 PLC device Item R2800,2801 PLC constant Details Set the value to be set in the data type R register used in the PLC program (ladder). Even if the data is set in the R register that corresponds to the PLC side when this parameter is displayed the screen will not change. Enter a different screen once and then select this screen again. (SETUP PARAM 6. 5/14) # 6349 PLC device Item R4900,4901 PLC constant Details Set the value to be set in the data type R register used in the PLC program (ladder). Even if the data is set in the R register that corresponds to the PLC side when this parameter is displayed the screen will not change. Enter a different screen once and then select this screen again. Setting range 99999999 to 99999999 Setting range 99999999 to 99999999

6348

R2894,2895

6396

R4994,4995

11.4 SELECTING THE PLC BIT

(SETUP PARAM 6. 6/14) to (SETUP PARAM 6. 7/14) # PLC device 6401 R2900-Low 6402 R2900-High Item Bit selection Details This is the bit type parameter used in the PLC program (ladder). Even if the data is set in the R register that corresponds to the PLC side when this parameter is displayed the screen will not change. Enter a different screen once and then select this screen again. Some of the parameters following #6449 may be fixed according to the usage purpose. Refer to the PLC Program Development On-board Instruction Manual. Setting range 0: OFF 1: ON

6495 R2947-Low 6496 R2947-High

(SETUP PARAM 6. 7/14) to (SETUP PARAM 6. 9/14) # PLC device 6497 R4400-Low 6498 R4400-High Item Bit selection expansion Details This is the bit type parameter (expansion) used in the PLC program (ladder). Even if the data is set in the R register that corresponds to the PLC side when this parameter is displayed the screen will not change. Enter a different screen once and then select this screen again. Setting range 0: OFF 1: ON

6595 R4449-Low 6596 R4449-High

II - 341

11. PLC CONSTANTS 11.4 SELECTING THE PLC BIT Table: "Contents of bit selection parameters #6449 to #6496"
Symbol name #6449 0 R2924 #6450 1 R2924 H L 7 NC card Controller thermal alarm on 6 5 4 3 Counter C retention Full screen display of message 2 Integrating timer T retention Operator message on Onboard editing not possible Integrating timer (fixed) retention 1 PLC counter program on 0 PLC counter program on

Setting display unit thermal alarm on External Alarm/ alarm operator message change display

1 0 R F Alarm system system message on

#6451 2 R2925 L -

PLC GX-Developer development communienvironment cation on selection GOT communication connection Counter (fixed) retention

Onboard on

#6452 3 R2925 H -

#6453 4 R2926 L Message language change code H

#6454 5 R2926

#6455 6 R2927 L -

#6456 7 R2927 H -

#6457 8 R2928 L High-speed input specification 1

#6458 9 R2928 H High-speed input specification 2

#6459 A R2929 L High-speed input specification 3 (Spare)

#6460 B R2929 H High-speed input specification 4 (Spare)

#6461 C R2930 L High-speed output specification 1

#6462 D R2930 H High-speed output specification 2

#6463 E R2931 #6464 F R2931 H High-speed output specification 4 (Spare) L High-speed output specification 3 (Spare)

II - 342

11. PLC CONSTANTS 11.4 SELECTING THE PLC BIT

0 1 2 3 4 5 6 7 8 9 A B C D E F

Symbol name #6465 R2932 L #6466 R2932 H #6467 R2933 L #6468 R2933 H #6469 R2934 L #6470 R2934 H #6471 R2935 L #6472 R2935 H #6473 R2936 L #6474 R2936 H #6475 R2937 L #6476 R2937 H #6477 R2938 L #6478 R2938 H #6479 R2939 L #6480 R2939 H

7 -

6 -

5 -

4 -

3 -

2 -

1 -

0 -

Standard PLC parameter

MC alarm 4 output off

(Note 1) Be sure to set the bits indicated - and blanks to 0. (Note 2) Parameters #6481 to #6496 are reserved for debugging by Mitsubishi.

II - 343

12.

MACRO LIST

12. MACRO LIST

(SETUP PARAM 7. 1/3) # 7001 to 7091 7002 to 7092 Item M [01] to M [10] Details <Code> Set the M code used for calling out the macro with the M command. This is valid when #1195 Mmac is set to 1. <Type> Set the macro call out type.
0 1 2 3 others M98 P; and equivalent value call G65 P; and equivalent value call G66 P; and equivalent value call G66.1 P; and equivalent value call M98 P; and equivalent value call

Setting range (unit) 1 to 9999

0 to 3

7003 to 7093 M2mac

<Program No.> Set the No. of the program to be called out.

1 to 99999999

7102 7103

Set the type and program No. for when calling out the macro with the 2nd miscellaneous command. The macro will be called out with the #1170 M2name address command when #1198 M2mac is set to 1. <Type> 0 to 3 Same as the M call macro. <Program No.> 0 to 99999999 Same as the M call macro. (SETUP PARAM 7. 2/3) Details <Code> Set the G code to be used when calling the macro with a G command. Do not set a G code used in the system. <Type> Same as the M call Marco. <Program No.> Same as the M call Marco.

# 7201 to 7291 7202 to 7292 7203 to 7293

Item G [01] to G [10]

Setting range (unit) 1 to 255

0 to 3

1 to 99999999

Smac

7302 7303 Tmac 7312 7313

Set the type and program No. for when calling the macro with an S command. This is valid when #1196 Smac is set to 1. <Type> 0 to 3 Same as the M call Marco. <Program No.> 1 to 99999999 Same as the M call Marco. Set the type and program No. for when calling the macro with a T command. This is valid when #1197 Tmac is set to 1. <Type> 0 to 3 Same as the M call macro. <Program No.> 0 to 99999999 Same as the M call macro.

II - 344

12.

MACRO LIST

(SETUP PARAM 7. 3/3) # 7401 Item ASCII [01] Valid Details The ASCII code macro parameters (#7402 to 7405) are validated. 0: Invalid 1: Valid Set the ASCII code used to call macros with the ASCII code. Setting range 0/1

7402

Code

7403 7404 7405 7411 ASCII [02]

Type Program No. Variable Valid

7412

Code

Set the macro call type. 0: M98, 1: G65, 2: G66, 3: G66.1 Set the number of the program called with macro call. When the call type is "0", set the variable number set after the ASCII code. The ASCII code macro parameters (#7412 to 7415) are validated. 0: Invalid 1: Valid Set the ASCII code used to call macros with the ASCII code.

L system: A, B, D, F, H, I, J, K, M, Q, R, S, T M system: A, B, F, H, I, K, M, Q, R, S, T 0 to 3 0 to 99999999 100 to 149 0/1

7413 7414 7415

Type Program No. Variable

Set the macro call type. 0: M98, 1: G65, 2: G66, 3: G66.1 Set the number of the program called with macro call. When the call type is "0", set the variable number set after the ASCII code.

L system: A, B, D, F, H, I, J, K, M, Q, R, S, T M system: A, B, F, H, I, K, M, Q, R, S, T 0 to 3 0 to 99999999 100 to 149

II - 345

13. POSITION SWITCH 13.1 OUTLINE OF FUNCTION

13. POSITION SWITCH

13.1 OUTLINE OF FUNCTION

The position switch (PSW) is used as an alternate switch for the dog switch provided on an axis of the machine. The position switch uses parameters by which the names of axes and their corresponding coordinates indicating imaginary dog positions are defined in advance. When the machine reaches the imaginary dog position a signal is output to the PLC interface. The position switch thus works as an imaginary dog switch. (SETUP PARAM 8. 1/1) # 7500 Pcheck Item High-speed switching of position switch Details Specify whether to perform position switch area checking at high speeds. 0: Do not perform position switch area checking at high speed (do it the same as before). 1: Perform position switch area checking at high speed. Specify the name of the axis for which a position switch is provided. When the machine enters the range between imaginary dog positions 1 and 2, a signal is output to the PLC. System 1 device X 270 System 2 device U0F0 When position switch area checking at high speed is selected, specify the mode of area checking, i.e., whether to use the command type machine position or detector feedback position, for each position switch point. 0: Use the command type machine position as the machine position for position switch area checking. 1: Use the detector feedback position as the machine position for position switch area checking. Note: This parameter is valid only when 1 set in #7500 Pcheck. Setting range (unit) 0/1

75 1 75 2

<axis> <dog1>

Axis name Imaginary dog position 1 Imaginary dog position 2 Selection of area check method

X, Y, Z, U, V, W, A, B, or C axis address 99999.999 to 99999.999 (0.001mm)

75 3 75 4

<dog2> <check>

0/1

II - 346

13. POSITION SWITCH 13.1 OUTLINE OF FUNCTION

Position switch numbers of PSW1 to PSW8 and signal devices <axis> PSW1 PSW2 PSW3 PSW4 PSW5 PSW6 PSW7 PSW8 #7501 #7511 #7521 #7531 #7541 #7551 #7561 #7571 <dog1> #7502 #7512 #7522 #7532 #7542 #7552 #7562 #7572 <dog2> #7503 #7513 #7523 #7533 #7543 #7553 #7563 #7573 System 1 device X270 X271 X272 X273 X274 X275 X276 X277 System 2 device U0F0 U0F1 U0F2 U0F3 U0F4 U0F5 U0F6 U0F7

Instead of the dog switch provided on the machine axis the coordinate values indicating imaginary dog positions (dog1 and dog2) on the coordinate axis of the axis name preset with axis are set with the position switches (PSW1 PSW8). When the machine reaches the position the signal is output to the device corresponding to the PLC interface. Example of settings of dog1 and dog2 and operation Setting of dog1 and dog2 dog1 < dog2 dog1 > dog2 dog1 = dog2 dog1, dog2 position
dog1 dog2

Operation A signal is output between dog1 and dog2. A signal is output between dog1 and dog2. If dog1 equals dog2 the dog1 position triggers a signal.

Basic machine coordinate system zero point Imaginary dog

dog1 dog2

PSW width

dog2

dog1

dog1 = dog2

II - 347

13.2

13. POSITION SWITCH CANCELING THE POSITION SWITCH

Rotation axis Setting of dog1 and dog2 dog1 < dog2 dog1, dog2 position
dog2 dog1 (Example) dog1 = 30.000 dog2 = 330.000

Description A signal is output between dog1 and dog2.

dog1

dog2 (Example) dog1 = -30.000 dog2 = 30.000

A signal is also output when dog1 is negative.

dog1 > dog2

dog1

dog2 (Example) dog1 = 330.000 dog2 = 30.000

A signal is output between dog2 and dog1.

dog1 dog2 360

dog2 dog1 (Example) dog1 = 30.000 dog2 = 390.000

A signal is kept output when the difference between dog1 and dog2 exceeds 360 degrees.

13.2 CANCELING THE POSITION SWITCH

To cancel the position switch enter the number (#75 1) of the position switch to be canceled in # ( ) of the setting field enter a slash "/" in DATA ( ) then press the INPUT key. This deletes the axis name for the specified position switch thus invalidating the position switch. The data specified for <dog1> and <dog2> are still stored in memory. To validate the position switch again therefore it is enough to specify the axis name only.

II - 348

14.

AUXILIARY AXIS PARAMETER SCREEN

14. AUXILIARY AXIS PARAMETER SCREEN

Turn the NC power OFF after setting parameters indicated with a (PR) in the table. The setting will be validated after the power is turned ON again. No. 1 MSR (PR) 2 RTY (PR) Name Motor series Details Setting range Default value 0000

Set the motor series. This is automatically judged 0000 to FFFF by the system when the default value (0000) is (hexadecimal) set. Set the regenerative resistor type. Do not set values without a description.
0 0 0 0 (Default setting value) Setting value 0 Details Amplifier standard built-in resistor (10CT has no built-in resistor) Setting prohibited MR-RB032 (30W) MR-RB12 (100W) MR-RB32 (300W) MR-RB30 (300W) MR-RB50 (500W)

Regeneration option type

0000 to FFFF (hexadecimal)

0000

1 2 3 4 5 6 7~F

3 PC1 (PR)

Motor side gear ratio (machine rotation ratio)

4 PC2 (PR)

Set the No. of gear teeth on the motor side and the No. of gear teeth on the machine side as an integer reduced to its lowest terms. Set the total gear ratio if there are multiple gear Machine side levels. For rotation axes, set the No. of motor rotation gear ratio (motor rotation speed per machine rotation. ratio) Feed pitch Set 360 (default value) for rotation axes. Set the feed lead for linear axes.

1 to 32767

1 to 32767

5 PIT (PR) 6 INP

1 to 32767 ( or mm)

360

In-position In-position is detected when the position droop detection width becomes this setting value or less.

1 to 32767 50 (1/1000 or m)

II - 349

14. AUXILIARY AXIS PARAMETER SCREEN

No. 7 ATU

Name Auto-tuning

Details

Setting range

Default value 0102

Set the adjustment of the auto-tuning. Do not set 0000 to FFFF (hexadecimal) values without a description.
0 1 0 2 (Default setting value) Setting Details value 1 Low response (low-rigidity loads, loads which easily vibrate) 2 Standard setting value 3 Standard setting value 4 Standard setting value 5 High response (high-rigidity loads, loads which do not easily vibrate) Setting Details value 0 Standard 2 Large friction amount (set the position loop gain slightly lower) Setting Details value 0 Only auto-tuning PG2, VG2, VIC, and GD2. 1 Only auto-tuning PG1, PG2, VG1, VG2, VIC, and GD2 (total gain). (Standard setting) 2 No auto-tuning.

8 9

PG1

Position loop gain 1 Deceleration control time constant

Set the position loop gain for the model loop. (Not used.)

4 to 1000 (1/s)

70 0

10 EMG

Set the deceleration time from the clamp speed 0 to 32768 (ms) 500 (Aspeed1). For normal rapid traverse, set the same value as the acceleration/deceleration time constant. (Not used.) (Not used.) 0 0 100

11 12 FFC 13 MBR Vertical axis drop prevention time Notch filter No.

Input the time the servo OFF is delayed during 0 to 1000 (ms) servo OFF command. Increase the setting by 100ms at a time and set the minimum value where the axis does not drop. Set the frequency of the machine resonance suppression filter. Do not set values without a description.
Setting 0 1 2 value Frequency No (Hz) start 1125 563 3 375 4 282 5 225 6 7

14 NCH

0 to 9

188 161

15 KEG

(Not used.)

II - 350

14.

AUXILIARY AXIS PARAMETER SCREEN

No. 16 JIT

Name Jitter compensation

Details

Setting range

Default value

Set the No. of ignored jitter compensation pulses. 0 to 3 Do not set values without a description.
Setting value Number of ignore pulses 0 No start 1 1125 2 563 3 375

17 MV1 18 MV2 19 PG2 Position loop gain 2 Speed loop gain 1 Speed loop gain 2

(Not used.) (Not used.) Set the position loop gain of the actual loop. Determine the position responsiveness for external disturbance. Set the speed loop gain of the model loop. Determine the tracking ability regarding the speed commands. 1 to 500 (1/s)

0 0 25

20 VG1

20 to 5000 (1/s) 1200

21 VG2

Set the speed loop gain of the actual loop. 20 to 8000 (1/s) 600 Determine the speed responsiveness for external disturbance. 1 to 1000 (ms) 20 1000

22 VIS 23 VDC

Speed integral Determine the characteristics of the speed compensation low-frequency region. Speed differential compensation Load inertia ratio Motor type

PI control normally results from a default value of 0 to 1000 1000. Adjust the overshoot amount by lowering in increments of 20. Set the load inertia ratio for the motor inertia. (Not used.) Set the motor type. This is automatically judged by the system when the default value (0000) is set. 0000 to FFFF (hexadecimal) 0.0 to 50.0 (fold)

24 DG2 25 30 MTY (PR)

2.0 0 0000

II - 351

14. AUXILIARY AXIS PARAMETER SCREEN

No. 50 MD1

Name D/A output channel 1 data No.

Details

Setting range

Default value 0000

Set the Nos. of the data to be output on D/A output 0000 to FFFF (hexadecimal) channel 1.
0 0 0 0 (Default setting value)

Setting value 0 1 2 3 4 5 6 7 8 9 A

Details Speed feedback (with sign) Maximum rotation speed = 8V Current feedback (with sign) Maximum current (torque) = 8V Speed feedback (without sign) Maximum rotaion speed = 8V Current feedback (without sign) Maximum current (torque) = 8V Current command Maximum current (torque) = 8V Command FT 100000 [degrees/min] = 10V Position droop 1 (1/1) 2048 [pulse] = 10V Position droop 2 (1/4) 8192 [pulse] = 10V Position droop 3 (1/16) 32768 [pulse] = 10V Position droop 4 (1/32) 65536 [pulse] = 10V Position droop 5 (1/64) 131072 [pulse] = 10V

51

MO1

D/A output channel 1 output offset D/A output channel 2 data No. D/A output channel 2 output offset

Set this value when the zero level of D/A output channel 1 is not suitable. (Not used.)

999 to 999 (mV)

52 53

MG1 MD2

Set the Nos. of the data to be output on D/A output 0000 to FFFF channel 2. (hexadecimal) The descriptions are the same as "50 MD1". Set this value when the zero level of D/A output channel 2 is not suitable. (Not used.) (Not used.) 999 to 999 (mV)

0000

54

MO2

55 56

MG2 sty02 No. of indexing stations

100 station (PR)

Set the No. of stations. For linear axes, this value 2 to 360 is expressed by: No. of divisions = No. of stations 1.

II - 352

14.

AUXILIARY AXIS PARAMETER SCREEN

No. 101 Cont1 (PR)

Name Control parameter 1

Details

Setting range

Default value 0200

This is a HEX setting parameter. Set bits without a 0000 to FFFF description to their default values. (hexadecimal)
bit F E D C B A 9 8 7 6 5 4 3 2 1 0 Default 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 value bit Meaning when "0" is set High-speed zero point return after 1 establishment of zero point. Reference point return 8 direction (+) Rotation direction 9 determined by #2030 dir () Machine basic A position becomes the origin point D Coordinate zero point creation valid Rotation direction in #2030 dir () or in the shortcut direction Stopper direction is positioning direction Meaning when "1" is set Dog-type return for each zero point return operation. Reference point return direction () Rotation direction in the shortcut direction Electrical zero point becomes the origin point Zero point established at power supply ON position Rotation direction in the random position command sign direction Stopper direction is in the sign direction of the stopper amount

102 Cont2 (PR)

Control parameter 2

This is a HEX setting parameter. Set bits without a 0000 to FFFF description to their default values. (hexadecimal)
bit F E D C B A 9 8 7 6 5 4 3 2 1 0 Default 0 0 0 0 0 0 0 0 1 0 0 0 0 1 1 0 value bit Meaning when "0" is set Error not corrected at 1 servo OFF 2 Linear axis Station assignment 3 direction CW 4 Uniform index DO channel standard 5 assignment 7 Incremental detection Meaning when "1" is set Error corrected at servo OFF Rotation axis Station assignment direction CCW Non-uniform index DO channel reverse assignment Absolute position detection

0086

II - 353

14. AUXILIARY AXIS PARAMETER SCREEN

No. 103 EmgCont (PR)

Name Emergency stop control

Details

Setting range

Default value 0001

This is a HEX setting parameter. Set bits without 0000 to FFFF a description to their default values. (hexadecimal)
bit F E D C B A 9 8 7 6 5 4 3 2 1 0 Default 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 value bit Meaning when "0" is set Meaning when "1" is set External emergency External emergency stop invalid (default 0 stop valid value) Deceleration control Dynamic brake stop at 1 stop at emergency emergency stop stop NC bus emergency NC bus emergency 2 stop input valid stop input invalid NC bus emergency NC bus emergency 3 stop output valid stop output invalid

104 tleng (PR) 105 Axis nam 110 ZRNspeed

Linear axis Set the movement stroke length for linear axes. stroke length This is meaningless when setting non-uniform assignments or commanding random positions. Axis name Reference point return speed Set the name of the auxiliary axis.

0.001 to 99999.999 (mm) '0' to '9', 'A' to 'Z'

100.000

(4 characters) 1000

Set the clamp value of the feedrate when a 1 to 100000 reference point return is carried out. The feedrate (/min or becomes the manual operation speed of the mm/min) parameter group selected at that time, but it is clamped by this parameter setting value. 1 to 65535 (/min or mm/min)

111 ZRNcreep

Reference Set the approach speed to the reference point point return after dog detection during a reference point creep speed return. Grid mask

200

112 grid mask 113 grspc (PR) 114 ZRNshift

Set the amount that the dog is artificially 0 to 65536 0 extended. Set 1/2 the grid spacing as a standard. (1/1000 or m) 0

Grid spacing Divide the grid spacing that is the conventional 0 to 4 motor rotation movement amount into 2, 4, 8, or (1/2n division) 16 divisions. Reference point shift amount Station offset Set the shift amount in a dog-type reference point return from the electric zero point determined on the grid to the reference point.

0 to 65536 0 (1/1000 or m) 0.000

115 ST. ofset

Set the distance (offset) from the reference point 99999.999 to to station 1. 99999.999 ( or mm)

116 ABS Base (PR)

Absolute When movement of the machine coordinate zero 99999.999 to position zero point from the origin point is required during 99999.999 point absolute position initializing, set that movement ( or mm) amount. Soft limit (+) Commands in the plus direction that exceed this 99999.999 to setting value are not possible. If the machine is in 99999.999 a position exceeding the setting value, (mm) commands in the minus direction are possible. The soft limit function will not operate if Limit (+) and Limit () are set to the same value. Soft limit () Commands in the minus direction that exceed 99999.999 to this value are not possible. If the machine is in a 99999.999 position exceeding the setting value, commands (mm) in the plus direction are possible.

0.000

117 Limit (+)

1.000

118 Limit ()

1.000

II - 354

14.

AUXILIARY AXIS PARAMETER SCREEN

No.

Name

Details

Setting range

Default value 0004

120 ABS type Absolute position detection parameter

This parameter is set as a hexadecimal. Set the 0000 to FFFF default value for bits that have no description. (hexadecimal)
bit F E D C B A 9 8 7 6 5 4 3 2 1 0 Default 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 value bit Meaning when "0" is set Dogless-type method 1 initializing Mechanical stopper 2 method initializing Electrical zero point 3 direction (+) Meaning when "1" is set Dog-type method initializing Origin point alignment method initializing Electrical zero point direction ()

123 ABS check

Absolute position power OFF tolerable movement value

Set the value for the tolerable amount of 0.000 to movement for a machine that moved during 99999.999 power OFF in an absolute position detection ( or mm) system. The "Absolute position power OFF movement exceeded (ABS)" signal will turn ON if the machine moves more than this setting value during power OFF. The movement amount is not checked when this parameter is set to 0.000.

0.000

130 backlash

Backlash Set the backlash compensation amount. compensatio n amount (Not used.) (Not used.) (Not used.) Operation parameter group 1 Automatic operation speed

0 to 9999 0 (1/1000 or m) 0 0 0 0 5000

132 yobi16a 133 yobi16b 134 yobi32a 135 yobi32b 150 Aspeed1

(Not used.) Set the feedrate during automatic operation 1 to 100000 when operation parameter group 1 is selected. (/min or This parameter is regarded as the clamp value mm/min) for the automatic operation speeds and manual operation speeds of all operation groups. A speed exceeding Aspeed1 cannot be commanded, even if set in the "158 Aspeed2" to "174 Aspeed4" parameters. Set the feedrate during manual operation and JOG operation when operation parameter group 1 is selected. 1 to 100000 (/min or mm/min)

151 Mspeed1 Operation parameter group 1 Manual operation speed 152 time1.1 Operation parameter group 1 Acceleration/ deceleration time constant 1

2000

Set the linear acceleration/deceleration time for 1 to 9999 (ms) Aspeed 1(the operation parameter group 1 automatic operation speed (clamp speed)) when operation parameter group 1 is selected. When operating at speeds less than the clamp speed, the axis will linearly accelerate/decelerate at the inclination determined above. When this is set together with acceleration/deceleration time constant 2, S-character acceleration/deceleration is carried out. In this case, set the acceleration/deceleration time of the linear part in this parameter.

100

II - 355

14. AUXILIARY AXIS PARAMETER SCREEN

No. 153 time1.2

Name Operation parameter group 1 Acceleration/ deceleration time constant 2

Details

Setting range 1

Default value

Set this parameter when carrying out 1 to 999 (ms) S-pattern acceleration/ deceleration. When S-pattern acceleration/deceleration is carried out, set the total time of the non-linear parts. When "1" is set in this parameter, linear acceleration/deceleration is carried out. In the handle feed operation mode, this set value is regarded as the time constant for the linear acceleration/deceleration. Set the motor output torque limit value when 1 to 500 (%) operation parameter group 1 is selected. At the default value, the torque is limited at the maximum torque of each motor. Set the default value when torque limit is not especially required. In the stopper positioning operation mode, this becomes the torque limit value when positioning to the stopper starting coordinates. Set the excessive error detection width when 0 to 32767 operation parameter group 1 is selected. An ( or mm) alarm of excessive error (S03 0052) is detected when the position droop becomes larger than this setting value. The signal indicating that the machine position 0.000 to is at any one of the stations is the set position 99999.999 reached (JST) signal. During automatic ( or mm) operation, the automatic set position reached (JSTA) signal is also output under the same conditions. Set the tolerable values at which these signals are output when operation parameter group 1 is selected. These signals turn OFF when the machine position is separated from the station exceeding this value. The signal indicating that the machine position 0.000 to is near any one of the station positions is the 99999.999 near set position (NEAR) signal. ( or mm) Set the tolerable value at which this signal is output when operation parameter group 1 is selected. This value is generally set wider than the set position output width. During operations, this is related to special commands when the station selection is "0". Same as operation parameter group 1. This is the same as the operation parameter group 1.

154 TL1

Operation parameter group 1 Torque limit value

500

155 OD1

Operation parameter group 1 Excessive error detection width Operation parameter group 1 Set position output width

100

156 just1

0.500

157 near1

Operation parameter group 1 Near set position output width

1.000

158 Aspeed2 159 Mspeed2 160 time2.1 (Note 1) 161 time2.2 162 TL2 163 OD2 164 just2 165 near2

Operation parameter group 2

II - 356

14.

AUXILIARY AXIS PARAMETER SCREEN

No.

Name Operation parameter group 3

Details Same as operation parameter group 1.

Setting range This is the same as the operation parameter group 1.

Default value

166 Aspeed3 167 Mspeed3 168 time3.1 (Note 1) 169 time3.2 170 TL3 171 OD3 172 just3 173 near3 174 Aspeed4 175 Mspeed4 176 time4.1 (Note 1) 177 time4.2 178 TL4 179 OD4 180 just4 181 near4

Operation parameter group 4

Same as operation parameter group 1.

This is the same as the operation parameter group 1.

(Note 1) Set the linear acceleration/deceleration time constant for the automatic operation speed (clamp speed) of operation parameter group 1 in "160 time2.1". This also applies for "168 time3.1" and "176 time4.1".

II - 357

14. AUXILIARY AXIS PARAMETER SCREEN

No. 190 stpos1

Name Station 2 coordinate value Station 3 coordinate value Station 4 coordinate value Station 5 coordinate value Station 6 coordinate value Station 7 coordinate value Station 8 coordinate value Station 9 coordinate value PSW detection method

Details Set the coordinate value of each station when non-uniform assignment is selected. The station 1 coordinate value is fixed at 0.000 (machine coordinate zero point).

Setting range

Default value

99999.999 to 0.000 99999.999 ( or mm)

191 stpos2

192 stpos3

193 stpos4

194 stpos5

195 stpos6

196 stpos7

197 stpos8

198 PSWcheck

This is a HEX setting parameter. Set bits without 0000 to FFFF 0000 (hexadecimal) a description to their default values.
bit F E D C B A 9 8 7 6 5 4 3 2 1 0 Default 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 value bit Meaning when "0" is set The position switch 1 output is judged by the 2 machine position of 3 the command system. 4 5 6 7 Meaning when "1" is set The position switch output is judged by the machine FB position (actual position).

II - 358

14.

AUXILIARY AXIS PARAMETER SCREEN

No.

Name

Details When the machine position is in the region between region settings 1 and 2, the position switch of each No. will turn ON. Whether the value of setting 1 is larger than setting 2 (vice versa) does not affect the position switch operation. For rotation axes, the output turns ON at the region without including 0.000 degree.

Setting range

Default value 0.000

201 PSW1d PSW1 area 202 og1 setting 1 PSW1d PSW1 area og2 setting 2 203 PSW2d PSW2 area 204 og1 setting 1 PSW2d PSW2 area og2 setting 2 205 PSW3d PSW3 area 206 og1 setting 1 PSW3d PSW3 area og2 setting 2 207 PSW4d PSW4 area 208 og1 setting 1 PSW4d PSW4 area og2 setting 2 209 PSW5d PSW5 area 210 og1 setting 1 PSW5d PSW5 area og2 setting 2 211 PSW6d PSW6 area 212 og1 setting 1 PSW6d PSW6 area og2 setting 2 213 PSW7d PSW7 area 214 og1 setting 1 PSW7d PSW7 area og2 setting 2 215 PSW8d PSW8 area 216 og1 setting 1 PSW8d PSW8 area og2 setting 2 220 push Stopper amount Stopper standby time

Set the command stroke of the stopper 0.000 to operation during stopper positioning operations. 359.999 ( or mm) Set the standby time from the stopper starting coordinate positioning to the stopper operation start during stopper positioning operations. 0 to 9999 (ms)

0.000

221 pushT1

222 pushT2

Stopper Set the time from the completion of the stopper torque release operation to the changeover of the stopper time torque during stopper positioning operations. Set position signal output delay time Set the time from the completion of the stopper operation to the output of the automatic set position reached (JSTA), set position reached (JST), and near set position (NEAR) signals during stopper positioning operations.

0 to 9999 (ms)

223 pushT3

0 to 9999 (ms)

II - 359

Revision History
Sub No. Date 28 April 2004 First edition Revision

Notice
Every effort has been made to keep up with software and hardware revisions in the contents described in this manual. However, please understand that in some unavoidable cases simultaneous revision is not possible. Please contact your Mitsubishi Electric dealer with any questions or comments regarding the use of this product.

Duplication Prohibited
This instruction manual may not be reproduced in any form, in part or in whole, without written permission from Mitsubishi Electric Corporation. 1998-2003 MITSUBISHI ELECTRIC CORPORATION ALL RIGHTS RESERVED