1.

Types of OHTL Conductors (1) (2) (3) (4)

AAC All Aluminum Conductor. AAAC All Alloy Aluminum Conductor. ACAR Aluminum Conductor, Alloy Reinforced. ACSR Aluminum Conductor, Steel Reinforced.

Number (4) is the most common type used in OHTL.

The conductor normally composed of filaments or strands or lamination and this is

to over come the problem corona effect. Corona effect is a partial discharge due to high electric field around OHTL, this phenomena causes power loss and communication interference. As long as radius of conductor increase the electric field increase.

Erdu ai s

V = rl R n

So, as r E

So we decide to divide the conductor to small conductors called Strands or Lamination [in layers]. If N: number of conductors [strands] X: number of layers. Usually the relation between N&X take as followed;

N=3x2-3x+1
If N is given we can used the above relation get X, then we can get the total diameter of cable as

dT = (2x-1) d If N=19 19=3x -3x+1 x=3 dT = (2x-1) d +5d

2

2.0 CONDUCTORS
Conductors must be selected with sufficient thermal capability to meet continuous and emergency current ratings.

 Ratings of conductors applied to the PJM system should be determined using thePJM TSDS Bare Overhead Transmission Conductor Ratings, November 2000. The overhead line conductor and static wire should be chosen from those used by the TO. This provides the ability to quickly repair a section of line with utility stock material should an emergency arise. Standard transmission conductor types are ACSR, ACSR/AW, ACSS, and ACAR. Other conductor types will be reviewed by the TO. The ambient temperature range listed in Table 1 covers the PJM system and is used for the electrical ratings of the conductors as well as the structural loads upon the towers or poles.

3.0 CONDUCTOR SAG & TENSION CRITERIA

3.1 Alcoa Sag & Tension Common Point
The maximum tension case shall be allowed to default as the common point between the initial and final sag tables. No other common point shall be allowed. An example would be a common point based upon NESC Heavy conditions when calculated tensions for the 1-1/2Heavy Ice case exceeds those for the NESC case.

4.0 STRENGTH REQUIREMENTS

4.1. Structure Types the following descriptions of structure types shall
apply to the provisions for strength requirements 4.1.1. Suspension Structure A structure where the phase conductors and static wires are attached through the use of suspension insulators and hardware or, in the case of the static wire, with a clamp not capable of resisting the full design tension of the wire. 4.1.2. Strain Structure A structure where the phase conductors and static wires are attached to the structure by use of dead-end insulators and hardware but where the ability of the structure to resist a condition where all wires are broken on one side under full loading is not required or desired. Typically, strain structures would be used where the line deflection angle is 45 degrees or less. Structures subject to strain structure requirement shall be as identified by the Utility. 4.1.3. Dead-end Structure - A structure where the phase conductors and static wires are attached to the structure by use of dead-end insulators and hardware and where the ability of the structure to resist a condition where all wires are broken on one side under full loading is required or desired. Typically, dead-end structures would be used where the line deflection angle is greater than 45 degrees. Structures subject to dead-end structure requirement shall be as identified by the Utility. 4.1.4. Line Termination Structure A structure where the phase conductors and static wires are to be installed on one side only for the purpose of terminating the line, usually at a substation or switchyard. This permanent dead-end condition is assumed in the application of all applicable loading conditions.

4.2. Loading Definitions

4.2.1. Wind Pressure The pressure resulting from the exposure of a surface to
wind. The pressure values provided are for wind acting upon objects with circular cross section. Pressure adjustments for other shapes shall be as set forth by the ASCE Guidelines for Electrical Transmission Line Structural Loading (ASCE Publication 74) [ASCE 74]. Section V.A of PJM TSDS Technical Requirements 5/20/2002 Page 4 of 12 4.2.2. Radial Ice Radial ice is an equal thickness of ice applied about the circumference of the conductors and static wires. Ice density is assumed to be 57 lbs per cubic foot. For the purpose of transmission line design, ice is not applied to the surface of the structure, insulators, or line hardware. 4.2.3. Temperature Used for calculating conductor and static wire sag and tension. 4.2.4. Transverse load Forces or pressures acting perpendicular to the direction of the line. For angle structures, the transverse direction is parallel to the bisector of the angle of the transmission centerline. 4.2.5. Longitudinal load Forces or pressures acting parallel to the direction of the line. For angle structures, the longitudinal direction is perpendicular to the bisector of the angle of the transmission centerline. 4.2.6. All wires intact A condition where all intended spans of conductors and static wires are assumed to be in place. In the case of a Line Termination Structure, conductor and static wire spans are only on one side of the structure. 4.2.7. Broken Conductor or Static Wire A condition where one or more conductors or static wires are specified as broken. It is assumed that the broken conductor or static wire is in place on one side of the tower, and is removed from the other side. The span length for determination of loads from the conductor or static wire weight, wind pressure, and radial ice shall be not less than 60% of the design span length for the intact condition. 4.2.8. Load Factor A value by which calculated loads are multiplied in order of provide increased structural reliability. For the purpose of structural design, Overload Capacity Factors as specified by NESC shall be considered Load Factors.

5.0 ELECTRICAL DESIGN PARAMETERS

5.1 Right-Of-Way Width
The transmission line is to be designed with adequate right-of-way width to provide access for line maintenance, repair, and vegetation management as shown in Table 1. These widths are based upon the listed number of circuits on the right-of-way. For additional circuits, a wider right-of-way should be utilized. Vehicle or other means of access to each structure site is required for both construction and maintenance activities.

5.2 Wire to Ground Clearance

The minimum allowed clearance between the lowest transmission line conductor(s) shall meet the required NESC minimum plus a safety envelope of 3 feet. (The safety envelope is required to allow for sag and clearance uncertainties due to: actual

conductor operating temperature, conductor sagging error, ground topography accuracy, plotting accuracy and other sources of error. The inclusion of a safety envelope is considered to be prudent). The NESC minimum shall be calculated with the conductor at maximum operating voltage and the maximum operating temperature or maximum conductor loading. The minimum clearances should take into account the limitation of a 5 mA shock current as given in NESC Rule 232D3c. All areas beneath the line shall be assumed to allow vehicle access beneath the line. For agricultural areas that may utilize farming equipment, additional clearance will be provided to assure public safety and line reliability during the periods of farming and harvesting activities.

5.3 Wire to Signs, Structures, etc Under the Wires

The minimum allowed clearance between the lowest transmission line conductor(s) shall meet the required NESC minimum plus a safety envelope of 3 feet. The NESC minimum shall be calculated with the conductor at maximum operating voltage and the maximum operating temperature.

5.4 Wires to Structure Clearances

The minimum clearances between the phase conductors and the supporting tower or pole shall not be less than shown in Table 1. These clearances are to apply for all anticipated conductor positions from an every day condition to a displaced condition due to a 9-psf wind or ice loading. These clearances do not have any adders provided for birds or other animals, but are based upon the switching surge values listed in Table #1. Section V.A of PJM TSDS Technical Requirements 5/20/2002 Page 7 of 12

5.5 Wire-to-Wire Clearances

Clearance between the bottom transmission conductor and any lower wire shall meet the required clearance of NESC Rule 233 and 235as a minimum. When the lower wire is a non transmission wire, then the clearance should be at least 10 feet for voltages less than or equal to 230 kV, and 20 feet for voltages above 230 kV. This will allow safe personnel access to the non-transmission conductors. These clearances should be calculated with the transmission conductor at maximum operating temperatures or heavy ice, whichever provides greater conductor sag, and the non-transmission conductor at 0oF. Clearances between transmission conductors should be either the larger of clearances based upon switching surges, or clearances based on the NESC. The per unit switching surges to use for the calculation are shown in Table #1 Using switching surge values, the method used to determine the actual required clearance is given in section 5 of the EPRI Transmission Line Reference Book 115 kV - 138 kV Compact Line Design. For transmission conductors of different circuits, the clearances should be increased so that any wind induced dynamic conductor movement does not result in any breaker operations and subsequent reduction in transmission circuit reliability.

5.6 Conductor Operating Temperature and Conductor Sag

The conductor will be assumed to operate at or above the minimum temperature shown below, and at temperatures less than the maximum shown below. While the line conductor may be designed to operate at a lower temperature, the line must be sagged assuming the conductor temperature is at or above the minimum shown. For designed operating temperatures above the minimum shown, and still below the maximum, the line sag and clearances will be calculated for that operating temperature after rounding up to the nearest 10oC. In no case will a conductor operating temperature be allowed above the maximum shown in the table. Refer

to the PJM Bare Overhead Transmission Conductor Ratings for the ampacity and temperatures of conductors. Conductor Type Minimum Conductor Operating Temperature for Sagging and Clearance Purposes Maximum Operating Temperature ACAR 100oC 140oC ACSR, ACSS 125oC 180oC Consult with the local transmission utility for the maximum operating temperature since some companies use slightly different values. Higher values for ACSS conductors may only be used with specific approval from the TO. Studies of the long-term high temperature operation of all conductor-connected hardware must be investigated prior to the request for approval from the local transmission utility.

5.7 Insulation Requirements

The insulation system for the transmission line shall have values in excess of the leakage distance, 60 Hz wet, and Critical Impulse flashover specified in Table 1. These values shown are minimum conditions and may need to be increased in specific locations such as coastal environments, industrial smokestack sites, or high altitudes. (BIL values are not included here as they are associated with substation insulation and not transmission line insulation,) Section V.A of PJM TSDS Technical Requirements 5/20/2002 Page 8 of 12

5.8 Lightning Performance and Grounding

All transmission structures will be individually grounded through a dedicated earth driven grounding system composed of ground rods and / or buried counterpoise. This system is to be measured on each individual structure prior to the installation of any overhead conductors or wires. The maximum acceptable resistance measurement of this grounding system for voltages up to and including 230 kV is 25 Ohms, and 15 ohms for voltages 345 kV and greater. The grounding system may include radial counterpoise wires, equipotential rings, or both. The TO must approve all grounding methods, and connections to the grounding system that are below grade. These resistance requirements are to assure acceptable lightning performance on the line as well as provide for the safe grounding of the line by construction and maintenance forces. Individual tower grounding measurements will be allowed to exceed the 25 or 15 Ohms required only if the average value for the 5 adjacent structures along the line is less than the 25 or 15-Ohm restriction. To assure acceptable lightning performance, a shield wire is required above each transmission line. The number of shield wires and the maximum shielding angles between the shield wire and phase conductor are shown in Table 1. Each new structure design is to be analyzed using the EPRI MULTIFLASH or equivalent software to determine that the line design and actual grounding design provides the required lightning performance shown in Table 1. In instances where it is very difficult to provide the required lightning performance, the TO may grant permission to utilize a limited application of transmission lines arresters. In no case will chemical ground treatments be allowed to improve structure grounding.

5.9 EMF, RFI, TVI, and Audible Noise

The transmission line system is to be designed so that radio and TV interference is just perceptible at the edge of the right-of-way. This is typically the case with radio signal to noise ratios above 20 db, and TV signal to noise ratios above 40 db. The achievement of this level of performance is more of a problem for lines above 230 kV, so a radio frequency survey and investigation should be performed to measure actual radio and TV signal strength and calculate the signal to noise ratio. 5

Audible noise at the edge of the right-of-way should be calculated for the designed transmission line using wet conductor as the design condition. The resultant noise level must not exceed the level limited by the state and local authorities. Typically the limitation is 55 dbA during the daylight hours, and 50 dbA at night. Electric and Magnetic Field (EMF) levels are to be calculated using the EPRI ENVIRO or equivalent software and compared to any state or local limits. Modifications are to be made through phasing, structure height, ground clearance, etc. to assure these limitations are met. If no specific limitations exist, the line should be designed to the level of EMF on and adjacent to the right-of-way. A typical example of such an effort is the appropriate choice of phasing on the right-of-way.

5.10 Inductive Interference

A study should be done to determine the inductive impact upon other utilities due to the power flow in the new transmission line. The power flow may induce unusual currents and voltages in magnetic and electrical conductors that run parallel to the transmission line. When it is determined that the currents or voltages are being induced in nearby utilities or other facilities, the engineer for the new or modified line being constructed must take the appropriate corrective actions to eliminate or lower the currents or voltages to an acceptable level.

6.0 OTHER DESIGN PARAMETERS

6.1 Line Cascade Mitigation
Transmission line failures that cascade beyond the original structural failure must be avoided. To accomplish this, the design of a new or modified line shall incorporate dead-end strain structures routinely employed along the line. An alternative is to utilize suspension structures that are longitudinally guyed to resist full line tension if all wires on one side were broken. For wood construction, the strain structures shall also have inline storm guys utilized to provide the structural strength. The line tensions assumed for this condition are the NESC Heavy loadings on one side of the structure as defined above, and no tension on the other. The structures shall be placed routinely along the line to resist a line cascade, but in no case shall these structures be placed farther than 5 miles apart.

6.2 Corrosion Protection

Corrosion protection will be evaluated for all buried structural steel on transmission structures. This covers buried grillage, driven caissons, etc. The line designer will submit a recommendation to the TO for the corrosion mitigation method to be used for buried structural steel. The proposed method must show at least a 50 year durability before any degradation of structural strength is allowed. It is acceptable to include systems that require some routine maintenance such as cathodic protection using buried sacrificial anodes. Above grade steel will be protected from corrosion using a coating acceptable to the TO. Typical alternatives that have been used include weathering steel, galvanized steel, or painted steel.

6.3 Climbing Devices

6.3.1 Steel pole structures shall utilize climbing ladders. The TO shall specify the requirements and placement of the climbing ladders. 6.3.2 All steel towers shall be designed with step bolts as the provision for climbing. The TO shall specify the requirements and placement of the step bolts.

Note: There are two Tables in the pdf file very important pages: 11&12