Scribd
Upload
1K views

Transparently Bridge Two Networks Using MPLS - MikroTik Wiki

This document describes how to transparently bridge two wireless networks using MPLS Virtual Private LAN Service (VPLS). Two MikroTik routers are configured with wireless interfaces in bridge mode, LDP for MPLS signaling, and a VPLS tunnel between them to bridge the networks. Additional stations can be added by configuring more VPLS tunnels. The MTU on the MPLS interface must be increased to avoid fragmentation of packets encapsulated in the VPLS tunnel.

Uploaded by

Hendra Maulana
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views

Transparently Bridge Two Networks Using MPLS - MikroTik Wiki

This document describes how to transparently bridge two wireless networks using MPLS Virtual Private LAN Service (VPLS). Two MikroTik routers are configured with wireless interfaces in bridge mode, LDP for MPLS signaling, and a VPLS tunnel between them to bridge the networks. Additional stations can be added by configuring more VPLS tunnels. The MTU on the MPLS interface must be increased to avoid fragmentation of packets encapsulated in the VPLS tunnel.

Uploaded by

Hendra Maulana
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Transparently Bridge two Networks using MPLS - MikroTik Wiki

http://wiki.mikrotik.com/wiki/Transparently_Bridge_two_Networks_usi...

Transparently Bridge two Networks using MPLS


Contents
1 Overview 2 Configuration 3 MTU
Applies to RouterOS: v3, v4+

Overview
This a very basic example how to enable MPLS, establish VPLS tunnel between two wireless links and use it to transparently bridge two networks. There are several other ways to create this type of setup: Bridge using WDS Bridge using EoIP The MPLS/VPLS approach has some advantages: VPLS tunnel is about 60% faster and less overhead than EoIP tunnel 802.11n speed is limited over WDS bridges, this method doesn't have such limitations

Configuration
Let us assume the following network setup:

Note: For this setup to work in RouterOS 3.x, routing and mpls-test package must be installed. These features are included by default in 4.x. AP
# --configure wireless access point-/interface wireless set wlan1 disabled=no ssid=MPLS frequency=5180 band=5ghz mode=bridge # --configure IP-/ip address add address=172.16.0.1/30 interface=wlan1 # --enable LDP-/mpls ldp set enabled=yes lsr-id=172.16.0.1 transport-address=172.16.0.1 /mpls ldp interface add interface=wlan1 # --configure VPLS tunnel-/interface vpls add name=vpls1 remote-peer=172.16.0.2 vpls-id=1:1 disabled=no

1 of 3

3/19/2012 2:51 PM

Transparently Bridge two Networks using MPLS - MikroTik Wiki

http://wiki.mikrotik.com/wiki/Transparently_Bridge_two_Networks_usi...

# --add bridge and bridge ports -/interface bridge add name=bridge1 /interface bridge port add bridge=bridge1 interface=ether1 add bridge=bridge1 interface=vpls1

station
# --configure wireless access point-/interface wireless set wlan1 disabled=no ssid=MPLS band=5ghz mode=station # --configure IP-/ip address add address=172.16.0.2/30 interface=wlan1 # --enable LDP-/mpls ldp set enabled=yes lsr-id=172.16.0.2 transport-address=172.16.0.2 /mpls ldp interface add interface=wlan1 # --configure VPLS tunnel-/interface vpls add name=vpls1 remote-peer=172.16.0.1 vpls-id=1:1 disabled=no # --add bridge and bridge ports -/interface bridge add name=bridge1 /interface bridge port add bridge=bridge1 interface=ether1 add bridge=bridge1 interface=vpls1

Confirm that LDP is running


[admin@MikroTik] /mpls ldp neighbor> print Flags: X - disabled, D - dynamic, O - operational, T - sending-targeted-hello, V - vpls # TRANSPORT LOCAL-TRANSPORT PEER SEND-TARGETED ADDRESSES 0 DOTV 172.16.0.2 172.16.0.1 172.16.0.2:0 no 172.16.0.2 [admin@MikroTik] /mpls ldp neighbor> .. .. forwarding-table print Flags: L - ldp, V - vpls, T - traffic-eng # IN-LABEL OUT-LABELS DESTINATION INTERFACE NEXTHOP 0 expl-null 1 V 18 vpls1

Confirm that VPLS tunnel is established:


[admin@MikroTik] /interface vpls> monitor vpls1 once remote-label: 17 local-label: 18 remote-status: transport-nexthop: 172.16.0.2 imposed-labels: 17

Connect more stations to the same Bridge It is possibile to connect more than one Station to the same Bridge, simply creating more VPLS tunnels (one for Station, and don't forget to increase subnet size from /30 to /24 for example, dependig how much clients you need): AP
# --change wireless access point mode to AP Bridge-/interface wireless set wlan1 mode=ap-bridge # --configure second VPLS tunnel-/interface vpls add name=vpls2 remote-peer=172.16.0.3 vpls-id=2:2 disabled=no # --add vpls2 to bridge --

2 of 3

3/19/2012 2:51 PM

Transparently Bridge two Networks using MPLS - MikroTik Wiki

http://wiki.mikrotik.com/wiki/Transparently_Bridge_two_Networks_usi...

/interface bridge port add bridge=bridge1 interface=vpls2

2nd Station
# --configure wireless access point-/interface wireless set wlan1 disabled=no ssid=MPLS band=5ghz mode=station # --configure IP-/ip address add address=172.16.0.3/30 interface=wlan1 # --enable LDP-/mpls ldp set enabled=yes lsr-id=172.16.0.3 transport-address=172.16.0.3 /mpls ldp interface add interface=wlan1 # --configure VPLS tunnel-/interface vpls add name=vpls1 remote-peer=172.16.0.1 vpls-id=2:2 disabled=no # --add bridge and bridge ports -/interface bridge add name=bridge1 /interface bridge port add bridge=bridge1 interface=ether1 add bridge=bridge1 interface=vpls1

MTU
When router encapsulates Ethernet frame to forward over VPLS pseudowire, it checks if packet size + VPLS CW + MPLS labels exceeds MPLS MTU of outgoing interface. If it does, VPLS will fragment frame. In this example 1514byte layer2 packets are forwarded over VPLS, router adds CW (4bytes) and one MPLS tag (4bytes) it means that to avoid fragmentation MPLS MTU must be increased to 1522
/mpls interface set 0 mpls-mtu=1522

For more information and supported L2MTU values on RouterBoards refer to Maximum_Transmission_Unit_on_RouterBoards

Note: If interface does not support L2MTU specified as mpls-mtu, then packets will be silently dropped

3 of 3

3/19/2012 2:51 PM

You might also like