0% found this document useful (0 votes)

3K views

Simatic NCM Manager

Information on Advanced PC Configuration and SIMATIC NCM PC release 01 supported and not supported boards and software. The following components are supported by Advanced PC Configuration: Boards PROFIBUS CP 5613 / 5613FO, CP 5614 / 5614FO.

Uploaded by

Gritz John

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

3K views

Simatic NCM Manager

Uploaded by

Gritz John

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 196

Information on Advanced PC Configuration and SIMATIC NCM PC

Release 01

Information on

Advanced PC Configuration
and

SIMATIC NCM PC
Content
History of the document Supported and not supported boards and software Advanced PC Configuration Change to the SIMATIC NET PC-Software CD 07/2001 (Chapter 4: Part of the installation manual SIMATIC NET PC-Software CD 07/2001) Configuring PC Stations with SIMATIC NCM PC - Manual and Quick Start Part of the catalogue IK PI 2001 for PC boards and software Part of the catalogue IK PI 2000 for PC boards and software

Siemens AG 2001, All Rights Reserved. Technical data subject to change.

Information on Advanced PC Configuration and SIMATIC NCM PC

Release 01

History of the document

Release 01 Dated 07/2001 Changes compared to the previous release First release of this information collection on the items Advanced PC Configuration and NCM PC.

Siemens AG 2001, All Rights Reserved. Technical data subject to change.

Information on Advanced PC Configuration and SIMATIC NCM PC

Release 01

Supported and not supported boards and software

The following components are supported by Advanced PC Configuration:
Boards PROFIBUS CP 5613/5613FO, CP 5614/5614FO In relation with SIMATIC NET Software DP-5613/Windows from V6.0 on S7-5613/Windows from V6.0 on FMS-5613/Windows from V6.0 on CP5613 / CP5614 Software /Windows from V6.0 on SOFTNET-DP/Windows from V6.0 on SOFTNET-S7/Windows from V6.0 on SOFTNET-DP-Slave/Windows from V6.0 on SOFTNET-DP/Windows from V6.0 on SOFTNET-S7/Windows from V6.0 on SOFTNET-DP-Slave/Windows from V6.0 on S7-1613/Windows from V6.0 on PG-1613/Windows from V6.0 on SOFTNET-S7/Windows from V6.0 on SOFTNET-PG/Windows from V6.0 on SOFTNET-S7/Windows from V6.0 on SOFTNET-PG/Windows from V6.0 on Described in catalogue IK PI 2001

CP 5511 CP 5611
(and integr. PB interfaces in the IPCs/PGs -> Prerequisite: CP 5611 compatible)

IK PI 2001 IK PI 2001

Industrial Ethernet CP 1613 CP 1512* CP 1612*

(and integr. Ethernet interfaces of the IPCs/PGs)
* on preparation

IK PI 2001 IK PI 2001 IK PI 2001

More details can be found in description SIMATIC NET PC-Software CD 07/2001 chapter 4.3 and chapter 4.4.

Siemens AG 2001, All Rights Reserved. Technical data subject to change.

Information on Advanced PC Configuration and SIMATIC NCM PC

Release 01

The following components are not supported by Advanced PC Configuration:

Boards PROFIBUS CP 5613/5613FO, CP 5614/5614FO In relation with SIMATIC NET Software DP-5613/Windows up to V2.1 S7-5613/Windows up to V2.1 FMS-5613/Windows up to V2.1 CP5613 / CP5614 Software /Windows up to V2.1 SOFTNET-DP/Windows up to V5.3 SOFTNET-S7/Windows up to V5.3 SOFTNET-DP-Slave/Windows up to V1.2 SOFTNET-DP/Windows up to V5.3 SOFTNET-S7/Windows up to V5.3 SOFTNET-DP-Slave/Windows up to V1.2 DP-5412/Windows up to V5.2 S7-5412/Windows up to V5.2 FMS-5412/Windows up to V5.2 PG-5412/Windows up to V5.2 SOFTNET-DP/Windows up to V5.3 SOFTNET-S7/Windows up to V5.3 SOFTNET-DP-Slave/Windows up to V1.2 Described in catalogue IK PI 2000

CP 5511 CP 5611
(and integr. PB interfaces of the IPCs/PGs -> Prerequisite: CP 5611 compatible)

IK PI 2000 IK PI 2000

CP 5412 (A2)

IK 10 1999

CP 5411 MPI-ISA
(and integr. Interfaces of IPCs/PGs, which are not compatible to CP 5611)

IK 10 1999

Industrial Ethernet CP 1613 CP 1413 CP 1511 CP 1411

TF-1613/Windows all releases S7-1613/Windows up to V2.1 PG-1613/Windows up to V2.1 TF-1413/Windows all releases S7-1413/Windows all releases PG-1413/Windows all releases SOFTNET-S7/Windows up to V3.3 SOFTNET-PG/Windows up to V3.3 SOFTNET-S7/Windows up to V3.3 SOFTNET-PG/Windows up to V3.3

IK PI 2000 IK 10 1999 IK 10 1999 IK 10 1999

More details can be found in description SIMATIC NET PC-Software CD 07/2001 chapter 4.3 and chapter 4.4.

Siemens AG 2001, All Rights Reserved. Technical data subject to change.

SIMATIC NET PC Software CD 07/2001

Advanced PC Configuration Switching to the SIMATIC NET PC Software CD 07/2001

Introduction to Configuration

4.1

Description of Advanced PC Configuration

Advanced PC Configuration is the new tool with which you can commission a PC station as part of an industrial communication network. SIMATIC NET supports the option of using Advanced PC Configuration on a central engineering station to configure PC stations in the same way as programmable controllers. A networked PC with the SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 V5.1 Service Pack 2 program is used as the engineering station.

Features
Using Advanced PC Configuration means certain changes in the way you configure in your project: All settings are made and downloaded to the PC station with one tool during configuration. This tool is the SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 version 5.1 Service Pack 2 program or higher. Properties that were previously configured using the Set PG/PC Interface program are now part of the configuration and are downloaded to the PC station. These include, for example, the station address and the bus parameters. Creating several databases is no longer necessary. Properties that were previously specified in various configuration programs are now configured in SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 or higher. Examples of such configuration tools include COML S7, COM PROFIBUS. Configuration parameters for the OPC Server that were previously stored in TXT files are now configured in SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 and downloaded to the PC station.

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

SIMATIC NET PC Software CD 07/2001

The Tools of Advanced PC Configuration

Advanced PC Configuration includes the following tools: Commissioning Wizard The Commissioning Wizard allows simple and consistent commissioning of all modules and user programs supported by Advanced PC Configuration. It guides the user step by step through the installation and configuration of the PC station. Configuration Console The Configuration Console is a snap-in program embedded in the Microsoft Management Console (MMC) and provides a wide range of options for configuring PC hardware components and PC user programs as well as providing diagnostic functions. Settings for the OPC servers that ship with the communication software are also made in the Configuration Console. SIMATIC NCM PC With SIMATIC NCM PC V5.1, Service Pack 2, a new configuration tool for STEP 7-compatible PC configuration is available. Station Configuration Editor The Station Configuration Editor is the user interface of the Station Manager; it allows access to the component management of the PC station. In this sense, components are the modules and user programs involved in communication tasks. The Station Configuration Editor can also be used for diagnostic purposes.

Supported Modules
You will find a list of modules supported and not supported by Advanced PC Configuration in the hinw_e.rtf file on the SIMATIC NET product CD (<CD drive> sw cdintern hinw_e.rtf).

Consequences
The following sections explain the effects of switching to Advanced PC Configuration. You should also read the chapter Installation and Commissioning in the HTML document Industrial Communication for PG/PC supplied on the CD.

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

SIMATIC NET PC Software CD 07/2001

4.2
4.2.1

LDB and XDB Databases

Introduction

Consequences of the New Central Configuration

As of the SIMATIC NET PC software CD 07/2001, all SIMATIC NET PC software products have central configuration and download mechanisms. The configuration data are now stored in XDB databases. The previously used LDB databases can no longer be used. Existing XDB databases can continue to be used after importing them into the central data management of the PC station, the Station Configuration Editor.

Using the Databases and Central Data Management

The graphics on the following pages illustrate the new situation: Configurations in previous product versions and the use of databases New, totally integrated and uniform configuration with the Station Configuration Editor New, totally integrated and uniform configuration within Advanced PC Configuration with SIMATIC NCM PC V5.1 Service Pack 2/STEP 7 Version 5.1 Service Pack 2 or higher. The local or remote configuration data are downloaded using SIMATIC NCM PC/STEP 7. It is also possible to transfer the configuration data in the form of an XDB database that is also created with the Station Configuration Editor. The OPC server and its protocol-specific adapters are optional elements and are shown with broken lines.

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

SIMATIC NET PC Software CD 07/2001

4.2.2

Configurations up to SIMATIC NET CD 05/2000

Description
A configuration created with the tools of the SIMATIC NET product CDs up to and including SIMATIC NET CD 05/2000 will be called the previous configuration in the description below.

Previous Configuration with LDB Databases

Each protocol of each module required its own database. If the OPC server was used, it also required its own databases in TXT format for each protocol:

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

SIMATIC NET PC Software CD 07/2001

Previous Configuration with LDB and XDB Databases

Even when the entire communication of all modules for the S7 protocol was stored in the XDB database, separate databases were required for DP and FMS. An optional OPC server also had its own data storage:

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

SIMATIC NET PC Software CD 07/2001

4.2.3

Configuration with Advanced PC Configuration

Description
Configuration with Advanced PC Configuration means configuring with the tools of the SIMATIC NET CD Version 07/2001 or higher.

Central Data Management for all Components

The configuration information for all protocols, modules, and for OPC is all maintained in a central data management system. The configuration data can be transferred to the central data management in different ways. The following graphic illustrates an example of importing an XDB database created by SIMATIC NCM PC V5.1 Service Pack 2/STEP 7 Version 5.1 Service Pack 2.

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

SIMATIC NET PC Software CD 07/2001

4.2.4

Continued Use of Previous Configurations

Continued Use of Databases and Configuration Tools

The following table shows an overview of the previous database types and the corresponding configurations and indicates whether continued use is possible:

Protocol DP

Database Type LDB

Configuration Tool COM PROFIBUS

Continued Use Continued use not possible, the configuration must be recreated with SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 or higher. Continued use not possible, the configuration must be recreated with SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 or higher. Continued use not possible, the configuration must be recreated with SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 or higher. Continued use not possible, the configuration must be recreated with SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 or higher. Continued use possible, the XDB database must be imported. Continued use not possible, the configuration must be recreated with SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 or higher. Continued use possible, as previously with COML TF.

FDL

TXT

Text Editor

FMS

LDB

COM PROFIBUS

LDB

COML S7

S7 SEND/ RECEIVE

XDB TXT

STEP 7 Text Editor

LDB

COML TF

Note If you want to continue using the previous configuration tools, use the SIMATIC NET CD 05/2000.

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

SIMATIC NET PC Software CD 07/2001

4.3

Industrial Ethernet - Effects on Older Product Versions (SIMATIC NET CD 05/2000 and earlier)

Introduction
This section describes what changes are necessary in Industrial Ethernet systems if you are already using a SIMATIC NET CD 05/2000 product or a previous version.

PG-1413, S7-1413, TF-1413 up to version 5.2 with Service Pack 2 for Windows NT 4.0 or Windows 98
Situation: These products are not supported by the SIMATIC NET CD 07/2001. Simultaneous installation of these products with products of the new CD 07/2001 is not permitted and is prevented. Steps to take: Keep using the products of the SIMATIC NET 5/2000 CD if you want to use a CP 1413 in your computer or replace it with a CP 1613.

PG-1613 up to version 2.1 for Windows 2000 Pro or Windows NT 4.0

Situation: PG operation possible as before. Steps to take: None necessary

S7-1613 up to version 2.1 for Windows 2000 Pro or Windows NT 4.0

Situation: An S7 configuration created with the COML S7 program cannot be used. Steps to take: A configuration created with the COML S7 program must be recreated with SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 or higher. If the configuration was already created with STEP 7 (XDB), this STEP 7 project can continue to be used. You only need to download the configuration to the CP/PC station from STEP 7 Version 5.1 Service Pack 2 or higher.

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

SIMATIC NET PC Software CD 07/2001

TF-1613 up to version 2.1 for Windows 2000 Pro or Windows NT 4.0

Situation: Application associations will continue to be configured as previously with the COML TF program. Support of this protocol by SIMATIC NCM PC or STEP 7 with OPC is not planned. The SEND/RECEIVE programming interface included in the product TF-1613 can continue to be used unchanged. If you use the OPC interface, it will be possible, in future, to configure SEND/RECEIVE communication with SIMATIC NCM PC or STEP 7! Steps to take: None necessary

SOFTNET-PG up to version 3.3 for Windows 2000 Pro, Windows NT 4.0 or Windows 98
Situation: Windows 98 is no longer supported. PG operation under Windows 2000 Pro or Windows NT 4.0 remains possible and is unchanged. Steps to take: Under Windows 98, use the SIMATIC NET CD 05/2000.

SOFTNET-PG up to version 3.3 with Service Pack 2 for Windows 2000 Pro, Windows NT 4.0, Windows Me or Windows 98
Situation: Windows Me and Windows 98 are no longer supported. PG operation under Windows 2000 Pro or Windows NT 4.0 remains possible and is unchanged. Steps to take: Under Windows Me or Windows 98, use the SIMATIC NET CD 05/2000.

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

SIMATIC NET PC Software CD 07/2001

SOFTNET-S7 up to version 3.3 for Windows 2000 Pro, Windows NT 4.0 or Windows 98
Situation: Windows 98 is no longer supported. An S7 configuration created with the COML S7 program cannot be used. Steps to take: Under Windows 98, use the SIMATIC NET CD 05/2000. A configuration created with the COML S7 program must be recreated with SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 or higher. If the configuration was already created with STEP 7 (XDB), this STEP 7 project can continue to be used. You only need to download the configuration to the CP/PC station from STEP 7 Version 5.1 Service Pack 2 or higher.

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

SIMATIC NET PC Software CD 07/2001

4.4

PROFIBUS - Effects on Older Product Versions (SIMATIC NET-CD 05/2000 and earlier)

Introduction
This section describes what changes are necessary in PROFIBUS systems if you are already using a SIMATIC NET CD 05/2000 product (or a previous version).

DP-5412, FMS-5412, PG-5412, S7-5412 up to version 5.2 with Service Pack 2 for Windows NT 4.0 or Windows 98
Situation: These products are not supported by the SIMATIC NET CD 07/2001. Simultaneous installation of these products with products of the new CD 07/2001 is not permitted and is prevented. Steps to take: Keep using the products of the SIMATIC NET 05/2000 CD if you want to use a CP 5412 in your computer or replace it with a CP 5613.

DP 5613 up to version 2.1 for Windows 2000 Pro or Windows NT 4.0

Situation: A DP configuration created with the COM PROFIBUS program cannot be used. Steps to take: A DP configuration created with the COM PROFIBUS program must be recreated with SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 or higher. If the configuration was already created with STEP 7, this STEP 7 project can continue to be used. You only need to download the configuration to the CP/PC station from STEP 7 Version 5.1 Service Pack 2 or higher.

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

SIMATIC NET PC Software CD 07/2001

FMS-5613 up to version 2.1 for Windows 2000 Pro or Windows NT 4.0

Situation: An FMS configuration created with the COM PROFIBUS program cannot be used. Steps to take: An FMS configuration created with the COM PROFIBUS program must be recreated with SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 or higher.

S7-5613 up to version 2.1 for Windows 2000 Pro or Windows NT 4.0

SOFTNET-DP up to version 5.3 for Windows 2000 Pro, Windows NT 4.0 or Windows 98
Situation: Windows 98 is no longer supported. A DP configuration created with the COM PROFIBUS program cannot be used. It will be possible to configure Send/Receive communication on the basis of the FDL interface over OPC with SIMATIC NCM PC or STEP 7 in the future! Steps to take: Under Windows 98, use the SIMATIC NET CD 05/2000. A DP configuration created with the COM PROFIBUS program must be recreated with SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 or higher. If the configuration was already created with STEP 7, this STEP 7 project can continue to be used. You only need to download the configuration to the CP/PC station from STEP 7 Version 5.1 Service Pack 2 or higher.

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

SIMATIC NET PC Software CD 07/2001

SOFTNET-DP slave up to version 1.2 for Windows 2000 Pro, Windows NT 4.0 or Windows 98
Situation: Windows 98 is no longer supported. Steps to take: Under Windows 98, use the SIMATIC NET CD 05/2000.

SOFTNET-S7 up to version 5.3 for Windows 2000 Pro, Windows NT 4.0 or Windows 98
Situation: Windows 98 is no longer supported. An S7 configuration created with the COML S7 program cannot be used. Steps to take: Under Windows 98, use the SIMATIC NET CD 05/2000. A configuration created with the COML S7 program must be recreated with SIMATIC NCM PC V5.1 Service Pack 2 or STEP 7 Version 5.1 Service Pack 2 or higher. If the configuration was already created with STEP 7 (XDB), this STEP 7 project can continue to be used. You only need to download the configuration to the CP/PC station from STEP 7 Version 5.1 Service Pack 2 or higher.

SIMATIC NET PC Software CD 07/2001 S79220-A5822-X-01-7419

Preface, Contents

Configuring PC Stations with SIMATIC NCM PC

Manual Introduction and Notes on Switching to Advanced PC Configuration Configuring SIMATIC PC Stations Configuring the OPC Server

1 2 3

Manual and Quick Start

for SIMATIC NCM PC / STEP 7 V5.1 SP2 and higher

Quick Start Configuring the OPC Server Quick Start with PROFIBUS-DP Configuring the OPC Server Quick Start with Industrial Ethernet

4 5

Support and Training Glossary Index

A B

06/2001 C79000-G8976-C156 Release 01

Classification of the Safety-Related Notices

This manual contains notices which you should observe to ensure your own personal safety, as well as to protect the product and connected equipment. These notices are highlighted in the manual by a warning triangle and are marked as follows according to the level of danger:

Danger indicates that death, severe personal injury or substantial property damage will result if proper precautions are not taken.

Warning indicates that death, severe personal injury or substantial property damage can result if proper precautions are not taken.

Caution indicates that minor personal injury or property damage can result if proper precautions are not taken.

Vorsicht indicates that property damage can result if proper precautions are not taken.

Notice highlights important information on the product, using the product, or part of the documentation that is of particular importance and that can have detrimental results if ignored.

Note highlights important information on the product, using the product, or part of the documentation that is of particular importance and that will be of benefit to the user.
Trademarks
SIMATICR, SIMATIC HMIR and SIMATIC NETR are registered trademarks of SIEMENS AG. Third parties using for their own purposes any other names in this document which refer to trademarks might infringe upon the rights of the trademark owners.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Safety Instructions Regarding your Product:

Before you use the product described here, read the safety instructions below thoroughly.

Qualified Personnel
Only qualified personnel should be allowed to install and work on this equipment. Qualified persons are defined as persons who are authorized to commission, to ground, and to tag circuits, equipment, and systems in accordance with established safety practices and standards.

Correct Usage of Hardware Products

Note the following

Warning This device and its components may only be used for the applications described in the catalog or the technical description, and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens. This product can only function correctly and safely if it is transported, stored, set up, and installed correctly, and operated and maintained as recommended. Before you use the supplied sample programs or programs you have written yourself, make certain that no injury to persons nor damage to equipment can result in your plant or process. EU Directive: Do not start up until you have established that the machine on which you intend to run this component complies with the directive 89/392/EEC.

Correct Usage of Software Products

Note the following

Warning This software may only be used for the applications described in the catalog or the technical description, and only in connection with software products, devices, or components from other manufacturers which have been approved or recommended by Siemens. Before you use the supplied sample programs or programs you have written yourself, make certain that no injury to persons nor damage to equipment can result in your plant or process.

Copyright E Siemens AG 1999/2000 All rights reserved The reproduction, transmission or use of this document or its contents is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved.

Disclaimer of Liability We have checked the contents of this manual for agreement with the hardware and software described. Since deviations cannot be precluded entirely, we cannot guarantee full agreement. However, the data in this manual are reviewed regularly and any necessary corrections included in subsequent editions. Suggestions for improvement are welcomed.

Siemens AG Bereich Automatisierungstechnik Geschftsgebiet Industrie-Automatisierung Postfach 4848, D-90327 Nrnberg Siemens Aktiengesellschaft

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Subject to technical change. G79000-G8976-C156-01

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

This manual...
... supports you and helps you to make efficient use of the communications functions of your PC applications in conjunction with the SIMATIC NET modules. ... supplements the OPC documentation on the SIMATIC NET PC / Windows CD. The descriptions are structured as shown below:

Manual / Quick Start SIMATIC NCM PC

PC CD / OPC Documentation

S General
information on PC tools

Configuring OPC from A to Z

You will find tools for every situation here:

S Functions of NCM
PC

S Detailed OPC
description

S Configuring the
OPC Server

S OPC tools and

Active X controls

S OPC application with

communication over Ethernet

Quick Starts

S OPC application
with communication over Ethernet.

S OPC application with

access to a DP master system

S OPC application
with access to a DP master system

S PROFInet
applications

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

This manual...

Additional Information
This manual is also part of the documentation packages for NCM S7 for PROFIBUS and Industrial Ethernet. Tip: This symbol appears in the margin to draw your attention to useful tips.

Additional Information on SIMATIC S7 and STEP 7

The following documentation contains additional information about the STEP 7 standard software of the SIMATIC programmable controllers and can be obtained from your local Siemens office.
Topic Basic information for technical personnel using the STEP 7 standard software for control tasks with S7300/400 programmable controllers. Document STEP 7 basics with

S S S S

User Manual Programming Manual Manual for converting from S5 to S7 Primer for a fast start

Validity of this Manual

The information in this manual applies to S S Version 5.1 SP2 and higher of the SIMATIC NCM PC / STEP 7 configuration software with the NCM S7 for Industrial Ethernet / PROFIBUS options; CD 7/2001 and higher from SIMATIC NET

Conventions
References to other manuals and documentation are indicated by numbers in slashes /.../. These numbers refer to the titles of manuals listed in the References section of the Appendix. -

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Contents
1 2 Introduction and Notes on Switching to Advanced PC Configuration . . . . . . . Configuring SIMATIC PC Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 2.2 2.3 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5 2.4 2.5 2.6 2.7 2.7.1 2.7.2 3 Tools and Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using tools Station Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . Configuring with SIMATIC NCM PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Relationship Between SIMATIC NCM PC and STEP 7 . . . . . . . . . . . . . . . Creating a PC Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring a PC Station with HW Config . . . . . . . . . . . . . . . . . . . . . . . . . . . Creating a DP Master System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Downloading the Configuration Data to the PC Station . . . . . . . . . . . . . . . Commissioning Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PC Station Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Station Configuration Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Managing Components: Components Tab . . . . . . . . . . . . . . . . . . . . . . . . . Diagnostics Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 11 11 14 17 18 19 21 24 26 28 31 32 34 35 37 39 40 41 43 47 47 48 49 50 51 52 53 54 55 56 57 57 58 60 61 61 62 62 63

Configuring the OPC Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 3.2 3.3 Significance of Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring the Properties of the OPC Server . . . . . . . . . . . . . . . . . . . . . . . Configuring Connection Properties for the OPC Server . . . . . . . . . . . . . . .

Quick Start for the OPC Application for PROFIBUS-DP . . . . . . . . . . . . . . . . . . . . 4.1 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.2.5 4.2.6 4.2.7 4.2.8 4.2.9 4.2.10 4.2.11 4.2.12 Example of a PROFIBUS Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quick Start for PROFIBUS Communication with OPC . . . . . . . . . . . . . . . . Hardware and Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring the PC Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . STEP 7 Starting the PC Station Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . STEP 7 PC Station Wizard: Selecting the Editing Mode . . . . . . . . . . . . . STEP 7 PC Station Wizard: Changing Settings . . . . . . . . . . . . . . . . . . . . HW Config: Inserting a DP Master System . . . . . . . . . . . . . . . . . . . . . . . . . . HW Config: Inserting a DP Slave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HW Config: Downloading the Configuration . . . . . . . . . . . . . . . . . . . . . . . . . STEP 7 Commissioning Wizard: Specifying the Use of Symbol Files . . OPC Scout: Establishing a Connection to the OPC Server . . . . . . . . . . . . OPC Scout: Inserting a Group and Variables . . . . . . . . . . . . . . . . . . . . . . . . OPC Scout: Displaying and Modifying Values of Variables . . . . . . . . . . . .

Quick Start for the OPC Application for Industrial Ethernet . . . . . . . . . . . . . . . . 5.1 5.2 5.2.1 5.2.2 Example of an Industrial Ethernet Configuration . . . . . . . . . . . . . . . . . . . . . Quick Start for Industrial Ethernet Communication with OPC . . . . . . . . . . Hardware and Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring the PC Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Contents

5.2.3 5.2.4 5.2.5 5.2.6 5.2.7 5.2.8 5.2.9 5.2.10 5.2.11 5.2.12 5.2.13 5.2.14 A

STEP 7 Starting the PC Station Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . STEP 7 PC Station Wizard: Selecting the Editing Mode . . . . . . . . . . . . . STEP 7 PC Station Wizard: Opening the Project . . . . . . . . . . . . . . . . . . . STEP 7 PC Station Wizard: Changing Settings . . . . . . . . . . . . . . . . . . . . STEP 7 NetPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . STEP 7 NetPro: Downloading the Configuration . . . . . . . . . . . . . . . . . . . . . STEP 7 Commissioning Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Symbol File Configurator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SIMATIC NET Commissioning Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OPC Scout: Establishing a Connection to the OPC Server . . . . . . . . . . . . OPC Scout: Inserting a Group and Variables . . . . . . . . . . . . . . . . . . . . . . . . OPC Scout: Displaying and Modifying Values of Variables . . . . . . . . . . . .

65 66 67 68 69 70 70 71 72 73 74 76 77 77 79

SIMATIC NET Support and Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Customer Support, Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Introduction and Notes on Switching to Advanced PC Configuration

Advanced PC Configuration is the new tool with which you can commission a PC station as part of an industrial communication network. SIMATIC NET supports the option of using Advanced PC Configuration on a central engineering station to configure not only PC stations but also, for example, operator stations. The engineering station is a networked PC with the SIMATIC NCM PC program or STEP 7.

Tools of Advanced PC Configuration

S Commissioning Wizard The Commissioning Wizard allows simple and consistent commissioning of all modules and user programs supported by Advanced PC Configuration. It guides the user step by step through the installation and configuration of the PC station. S Configuration Console The Configuration Console is a snapin program embedded in the Microsoft Management Console (MMC) and provides a wide range of options for configuring PC hardware components and PC user programs as well as providing diagnostic functions. Settings for the OPC servers that ship with the communication software are also made in the Configuration Console. S SIMATIC NCM PC and PC Station Wizard With SIMATIC NCM PC V5.1, Service Pack 2, a new configuration tool for STEP 7compatible PC configuration is available. S Station Configuration Editor The Station Configuration Editor is the user interface of the Station Manager; this allows you access to the component management of the PC station. The following Chapter LEERER MERKER also contains information on these tools and other related utilities.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Introduction and Notes on Switching to Advanced PC Configuration

Features Comparison with Previous Products

The new features of the SIMATIC NET software involve several changes to the previous configuration procedures and these are summarized below: S S All settings are made with one tool during configuration and downloaded completely to the PC station. This tool is SIMATIC NCM PC or STEP 7. Properties that were previously configured using the Set PG/PC Interface program are now part of the configuration and are downloaded to the PC station. These include, for example, the station address and the bus parameters. It is no longer necessary to create several databases. Properties that were previously specified in various configuration programs are now configured in SIMATIC NCM PC / STEP 7. Examples of such configuration tools include COML S7, COM PROFIBUS. Configuration parameters for the OPC Server that were previously stored in TXT files are now configured in SIMATIC NCM PC / STEP 7 and downloaded to the PC station.

LDB Databases no Longer Required

By configuring on a central station and with the option of downloading, LDB databases are no longer required for the DP, FMS, and S7 protocols. Existing XDB files can continue to be used; they must be imported into the central data management on the PC station using the Station Configuration Editor or PC Station Wizard.

Note For more detailed information on the difference between the previous methods and working with the software and modules, refer to the CD documentation and the Installation Instructions of the SIMATIC NET PC software products.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

Communication with PC Applications

PC applications that communicate with each other or with other stations such as S7 stations, PC stations, or operator control and monitoring stations use SIMATIC NET communications modules and software components. Before such communication is possible, you must first set up the communication services on your PC. This chapter explains how to use the tools and utilities with which you set up the PC components for communications tasks.

2.1

Tools and Utilities

SIMATIC NCM PC Configuration Tool

SIMATIC NCM PC is the central tool for configuring the communications services for your PC station. After creating your configuration data with this tool, you then download it to the PC station. The PC station is then ready for communication.

Note You can configure both in SIMATIC NCM PC and in STEP 7. STEP 7 also provides all the SIMATIC NCM PC functions described here for configuring your PC. From now on, the description will only refer to SIMATIC NCM PC but nevertheless applies to both.

Station Manager with the Station Configuration Editor

With the Station Configuration Editor, you can both display and edit the list in which the components are managed in the Station Manager on a PC station. The Station Configuration Editor also provides diagnostic services.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

Wizards Mean Less Work

The following wizards can be used in most situations. S Commissioning Wizard A Commissioning Wizard helps you to integrate a newly installed communications module in a few simple steps so that subsequent configuration with the PC Station Wizard and the SIMATIC NCM PC configuration tool is normally extremely simple. The existing configuration of the PC can be queried automatically; you do not need to call up the Station Configuration Editor explicitly. S PC Station Wizard The PC Station Wizard helps you when creating and handling projects for the SIMATIC NCM PC configuration tool. You can call it up either directly or start it when using the Commissioning Wizard. The following graphic shows the steps required and which tools to use. When you use the wizards, you are guided through these steps automatically and can assume that the configuration data created in SIMATIC NCM PC are consistent with the PC configuration.

Use the Commissioning Wizard! Use the PC Station Wizard!

Creating PC components with the Station Configuration Editor

Configuring communication services with SIMATIC NCM PC

S Creating connections S Setting up DP master systems S Downloading configuration data to

the PC station

PC station

Utilities for commissioning / operation:

S Configuration Console for settings and

diagnostics

S OPC Scout for displaying

communication variables and diagnostics

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

Further Utilities
From the graphic, you can see that there are other utilities available, for example for using the OPC Server interface. These utilities will be pointed out or described in greater detail where applicable. S Configuration Console A utility with which you can display the structure of a PC station in much the same way as in the Windows Explorer. The interactive options are Module diagnostics Setting the operating mode Configuration for specific situations S OPC Scout A utility that allows easy access to process data over the OPC interface. The interactive options are Displays of the configured communications channels representing the available OPC variables Monitoring, reading, and writing of process data

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.2

Using tools Station Configuration Options

Depending on where you install the configuration tool and how the PC station is networked, you have the following options: S S S Online networked (remote PC station) Online local Offline

The following descriptions illustrate when and where to use the tools and utilities in various situations.

Online Networked (Configuration Station and PC Station Networked)

PC station

Table 2-1 Tool / Utility ...use on Configuration Station SIMATIC NCM PC / STEP 7 is installed Station Configuration Editor yes no no optional Networked PC Station

S can be used to adapt a

target PC station to a configuration Commissioning Wizard optional recommended

S for setting up PG /PC

operation PC Station Wizard recommended

S for setting up modules

for productive communication no

S to edit a stored
configuration

S to create a new
configuration

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

Online Local (Configuration Station is also PC Station)

Table 2-2 Tool / Utility ...use on Configuration Station = PC Station SIMATIC NCM PC / STEP 7 is installed Station Configuration Editor yes optional

S can be used to adapt the PC station to a

configuration Commissioning Wizard recommended

S for setting up modules for productive

communication PC Station Wizard recommended to ...

S S S S

change local settings edit a stored configuration create a new configuration import XDB files

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

Offline (Configuration Station and PC Station not Connected)

Table 2-3 Tool / Utility ...use on Configuration Station SIMATIC NCM PC / STEP 7 is installed Station Configuration Editor yes no no yes Networked PC Station

S to import an XDB file

optional

S can be used to match

the actual configuration of a PC station to a planned configuration Commissioning Wizard no recommended

S for setting up modules

for productive communication PC Station Wizard recommended recommended

S to edit a stored
configuration

S to import an XDB file

S to create a new
configuration

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.3

Configuring with SIMATIC NCM PC

This chapter will familiarize you with the basic functions of SIMATIC NCM PC.

What the NCM PC Configuration Tool Does

The SIMATIC NCM PC Manager is a version of STEP 7 tailored for configuring PCs. It provides the functionality with which you can perform the following tasks for PC stations: S S S S S S Configure communication properties of the SIMATIC NET OPC Server Configure connections Configure the DP mode Set network parameters for PROFIBUS and Ethernet operation Download configuration data to PC stations Monitor communication to attached S7 stations with NCM Diagnostics

Further Information in Help

You will also find detailed information in the integrated help by selecting the menu command: S S Help " Introduction Contains a brief description of SIMATIC NCM PC Help " Getting Started Here you will find brief instructions on how to create a PC station, its applications and modules. For more detailed information, you can go from here to the PC topics in the main help system. These instructions are available only in Help on SIMATIC NCM PC. In STEP 7, select the Help menu directly: S Help Here you will find help topics relating to the PC station under: Configuring Hardware / SIMATIC PC Station Configuring Connections for a SIMATIC PC Station

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.3.1

Relationship Between SIMATIC NCM PC and STEP 7

SIMATIC NCM PC and STEP 7 are compatible with each other. You can S open and edit projects that you created with SIMATIC NCM PC at any time in STEP 7/SIMATIC Manager. This allows you to use additional functions for programming and configuring S7 stations.

Notice Optional packages are not supported by SIMATIC NCM PC. If you are editing a project that was created or edited in STEP 7, it may contain components from STEP 7 optional packages. If this is the case, you can only edit stations using SIMATIC NET PC that do not contain components from STEP 7 optional packages. S open and edit projects you created with STEP 7/SIMATIC Manager at any time in SIMATIC NCM. You can edit PC stations you have already created and create new PC stations. You can configure communication connections from these PC stations to existing S7 stations.

The restrictions in SIMATIC NCM PC relate to the S7 station types that can be configured and programming. You can see the differences in the following graphic: SIMATIC NCM PC STEP 7

S S S S

SIMATIC PC station Other station SIMATIC S5 PG/PC

S S S S

SIMATIC PC station Other station SIMATIC S5 PG/PC

after data import can be used for configuring connections:

S SIMATIC 400 station S SIMATIC 300 station S SIMATIC H station

Figure 2-1

S SIMATIC 400 station S SIMATIC 300 station S SIMATIC H station

The types of stations that you can configure only in STEP 7 can be used in SIMATIC NCM PC as target stations for a connection configuration after importing the project. After working on such a project in SIMATIC NCM PC, you can return it to STEP 7 and edit it again at any time.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.3.2

Creating a PC Station

Aims
You want to create configuration data for communication services for individual PC stations. This configuration data will then be downloaded to the PC station. After this, the PC applications can use the communications services. Tip: Remember that you can create a great deal of the project structure automatically using the PC Station Wizard! Read the information on starting and working with the wizard in Section 2.6. You will find examples in the Quick Start in Chapters 4 and 5.

Creating and Managing Objects

After starting SIMATIC NCM PC, you either open an existing project or create a new one. You use projects to manage your configurations consisting of all or part of the stations of your plant.
Objects are arranged in a hierarchical structure within a project.

For each PC station, you create a separate object of the type PC station.

These objects in turn contain the configuration and parameter data of the hardware and software. These objects are then used to assign the communications services. The objects are created with HW Config as shown in Section 2.3.3.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

Notice The name selected here for the PC station identifies the PC configuration. If you define a configuration for the local PC with NCM PC, the name you select must be identical to the name of the actual local configuration. If you define a configuration for a remote PC station, the name must not be identical to that of the actual local configuration! Otherwise, the local configuration would be overwritten when you download.

Follow the steps below:

1. Start up the SIMATIC NCM PC Manager. 2. You can create the stations with the insert objects function. 3. Opening a station object starts the HW Config tool with which you can create the configuration of a PC station consisting of modules and applications (see the following page).

Note When you start STEP 7, a wizard is opened that helps you to create a new project. In SIMATIC NCM PC, this wizard is replaced by the PC Station Wizard. Depending on your initial situation, this wizard provides you with more extensive support for your PC station. The PC Station Wizard also exists in STEP 7.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.3.3

Configuring a PC Station with HW Config

Creating an Image of the PC Configuration

To allow the configuration data sent by the configuration system to be assigned to a module or an application, they must have unique identification numbers. The identification number for modules, applications, and other components in a PC station is the index. You now place your applications and modules in slots in a virtual rack in HW Config. This slot number then corresponds to the index mentioned above. Notice Be careful not to confuse this Index with a hardware slot, for example on the PCI bus of the PC station. The slot on the PCI bus is not relevant for commissioning and is not used at any point.

Follow the steps below:

Drag the components from the catalog to the list (the virtual rack) displayed in HW Config. Notice Make sure you arrange the components exactly the same as in the configuration list of the Station Configuration Editor (see Section 2.7). If the configuration differs from the list, the configuration data that you download from SIMATIC NCM PC to the PC station will no be adopted correctly.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

PC Components in the Catalog

For the SIMATIC PC station, you can select the following components: S Application Application (standard application) You use standard interfaces to communicate with other applications and devices via your PC module. The user programs included in the application use suitable interfaces for communication, such as the SAPI programming interface or the SEND/RECEIVE programming interface. You can configure the following communications services depending on the module inserted: S7 connections FMS connections (PROFIBUS) DP services (DPV0 and DPV1) Note how these differ from the user programs that use the communication service as OPC clients via an OPC Server as described below.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

OPC Server You use the convenient interface to an OPC server to communicate with a programmable controller such as a SIMATIC S7-400. The OPC server can be set up as an interface for all available communications protocols. You can only create this object once in a PC station. You can then use this OPC Server for communication with any number of user programs (OPC clients). The following communications services can be used depending on the modules inserted: all types of connection DP services S S CP Industrial Ethernet This contains all the CP modules for attachment to Industrial Ethernet. CP PROFIBUS This contains all the CP modules for attachment to PROFIBUS.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.3.4

Creating a DP Master System

Read the information below if you want to use a PROFIBUS CP and configure a DP master system.

Significance of the Configuration Data in a DP Master System

The configuration data inform the DP master in the PC station of the data and address areas of the attached slaves. Depending on the type of slave, this information is either implicitly linked to the entry in the catalog or must be configured here additionally as, for example, when using an intelligent DP slave such as the CP 342-5.

Follow the steps below:

1. You have already placed the applications and modules as described in Section 2.3.3. 2. After you have taken the module from the catalog, you can select it and create a DP master system using the Insert menu command. 3. Select the application that will address the master system (the DP slaves).

The applications you have created are now ready to be assigned.

You can then see the DP master system you have created.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

Now insert the DP slaves you want to be addressed by the application from the catalog.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.3.5

Configuring Connections

Meaning
During operation, configured connections are established either implicitly or on request, depending on the parameter assignment. They are then available to the OPC Server or the PC application for communication.

General Rules
Regardless of the type of application, these general rules apply when configuring connections: S S S Communication connections are always assigned to an application. In the PC station, the CP that supports the type of connection is used for the data transfer. If there is more than one CP with this capability, you can use Routing to select the transmission path.

Follow the steps below:

1. Select the application to which you want to assign a connection.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2. Enter the desired connection type. When selecting the destination station, note the following: After creating a new project in SIMATIC NCM PC, you will normally find that the required destination station (for example an S7 station) does not exist. You then have the following options: Create an unspecified connection Select unspecified as the connection partner. In the Properties dialog box, you can then set the address parameters for the connection partner. Create a proxy object Create an Other Station. You then network this station by assigning the necessary interface types in the Properties dialog. This method is advisable if you intend to assign several connections to this partner station on the same interface in your project. Create a copy of an S7 station Insert the copy of an S7 station that you have created using STEP 7 in another project. You can then select this S7 station as your destination station.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.4

Downloading the Configuration Data to the PC Station

Notice Downloading as described below only results in successful installation of the communications services on your PC station if the arrangement of the components in the configuration data is identical with that of the configuration data on the PC station. See also Section 2.3.3.

Online Mode
The online mode allows you to download the configuration data directly to a PC station attached to the network (MPI, PROFIBUS or Ethernet) or to load the data on the local PC station if you are using this as the configuration station. S Online Networked (Configuration Station and PC Station Networked)

Download

Follow the steps below: 1. Switch the PG/PC station online. 2. Select the station you want to download to. 3. Download the configuration data with PLC > Download Make sure you set the correct interface in Set PG/PC Interface.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

Online Local (Configuration Station is also PC Station)

Load

Follow the steps below: 1. Select the station you want to load. 2. Load the configuration data using PLC > Download. Requirement: In the Set PG/PC Interface, you must first select the following setting as access point of the application: S7ONLINE (STEP7) > PC internal (local) Tip: If you use the PC Station Wizard, this setting is made automatically.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

Offline (Configuration Station and PC Station are not Connected)

If you are working offline, you will require an XDB file to transfer the data. The configuration system always generates an XDB file for each configured PC station.

XDB import

Follow the steps below to create and import an XDB file: 1. Select the station on which you want to load the data in the STEP 7 project. 2. Open the object properties of the station with the Station Properties menu command and select the Configuration tab. 3. Here, you can check and, if necessary, change the setting under Storage Location of the Configuration File. 4. Save and compile your project; you will then find the required XDB file in the folder you have selected. Note: The station name must be identical in the configuration and on the local PC station Entry in the Station Configuration Editor. 5. Copy the XDB file onto a data medium that the destination station can access. 6. Import the XDB file into your destination station using the Station Configuration Editor.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.5

Commissioning Wizard
When configuring the SIMATIC NET communications modules for the first time, you are supported by the Commissioning Wizard. The Commissioning Wizard takes you through the necessary steps for commissioning modules and the further steps for commissioning a PC station with configured communication. Tips: S S Refer to the examples in the Quick Start chapters in this manual. The tools and utilities were described in Section 2.2, Station Configuration.

The wizard opens...

S S S when you boot the PC station after inserting an additional module when you select the appropriate menu command in the Configuration Console tool when you select it in the Start menu

How to Use the Wizard

The basic steps are outlined below: 1. When you first configure the modules, all those that had not been detected previously are detected. For each module, you then set the operating mode and (if you select Configured mode) the networkrelated parameters for initial configuration. 2. After the Commissioning Wizard has run through all the previously undetected modules, confirm the settings you made for the modules. 3. If you want to configure communication on the PC station, you can now start the PC Station Wizard. When you have finished configuring, you return to the Commissioning Wizard. 4. If you intend to use the OPC server, you can decide whether to create a symbol file or use an existing one in the next step. 5. After this, the configuration is finally adopted and the PC is ready for the next steps.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.6

PC Station Wizard
The PC Station Wizard supports you when you create projects in SIMATIC NCM PC. It allows you to acquire the configure data of the PC station automatically. This helps you to make sure that your configuration data is consistent. Tips: S S Refer to the examples in the Quick Start section, Chapters 4 and 5. We have already described the interaction of the tools and utilities in Section 2.2, Station Configuration.

How to Start the PC Station Wizard

S From the Commissioning Wizard After you have finished configuring the modules, you start the wizard by clicking the corresponding button (see Section 2.5 and the Quick Start chapters). S From the Start menu Select Start " SIMATIC
"

SIMATIC NCM PC Station Wizard.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

The PC Station Wizard supports you in the following situations:

S Changing local settings If the SIMATIC NCM PC configuration tool is installed on the destination PC station, the wizard can compare the configuration data with the planned configuration data that already exist. The communications parameters can then be edited in the project directly. S Editing a saved configuration Open an existing project and compare the local configuration with the information in the project. In contrast to the Change Local Settings function, the configuration edited here is independent of an existing local configuration. S S Creating a new configuration Create a new project and enter the local configuration in the project. Starting the Station Configuration Editor When working offline, this option make use of an XDB file (configuration station and PC station are not connected see Section 2.2).

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.7

Station Configuration Editor

Purpose
The Station Configuration Editor is the central management entity for the components of the PC station. Components are the modules and communications tasks of active applications. The Station Configuration Editor can also be used for diagnostic purposes.

Modes
You can use the Station Configuration Editor for the local PC station or for a PC accessible over the network.

How to Start the Station Configuration Editor

The Station Configuration Editor is always available and started on the PC station on which you have installed the PC-CD. You can bring it to the foreground by clicking the icon shown here in the taskbar of the Windows desktop.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.7.1

Managing Components: Components Tab

Notice The components in the configuration list you can edit here must be entered in exactly the same order as in the component image you created in SIMATIC NCM PC with HW Config. If the configurations differ, the configuration data that you download to the PC station from SIMATIC NCM PC will not be adopted correctly.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

Creating a Component Configuration

S Automatic configuration using wizards In the simplest situation, you use the Commissioning Wizard and the PC Station Wizard to configure your PC station. In this case, the component configuration is acquired automatically. You then simply call the configuration editor described here to check the configuration or to run diagnostic checks. S Controlled configuration

1. First assign a name for the station by clicking the Station button. The name must match the name you assigned to the PC station when you configured the communications with SIMATIC NCM PC. 2. If you want the PC station to be accessible on the network, select the station by clicking the Host button. 3. Create the individual components for your PC station by clicking the Add button. The status display constantly informs you whether the component you have created matches the current hardware configuration and whether it matches any configuration that has already been downloaded.

Note You will find more information on the meaning of the display boxes and the buttons in the integrated help system.

Importing an XDB File

The communication configuration data are either downloaded directly to the PC station or imported using an XDB file (see Section 2.4). When required, the XDB file can be imported using the relevant button in the Station Configuration Editor. You can only import an XDB file when the configuration is an exact match.

Checking the Accessibility of the Module Ring Function

Once you have finished configuring, you can check the accessibility of the modules, by clicking the Ring button. If the module supports this function, you will see an indicator respond on the module.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

2.7.2

Diagnostics Tab

How It Works
The Station Configuration Editor manages a diagnostic buffer in which the PC station components (hardware and software) enter event information. You can use this list to analyze configuration or communication problems.

Note You will find more information on the meaning of the display boxes and the buttons in the integrated help system.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring SIMATIC PC Stations

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring the OPC Server

OPC Server
With the SIMATIC NET OPC Server described here, SIMATIC NET offers you a convenient tool with which your PC applications can write and read process data and receive notification of process events. By creating a configuration, you can specify the behavior of the OPC Server. You then download the configuration data to the PC station with NCM PC. This chapter describes the options available to you when configuring the OPC Server with the NCM PC configuration tool.

Where to Find Further Information

S S Creating PC stations and configuring connections: Please read Section 2.3 in this manual. Using the interface to the OPC Server in PC applications: How you address the OPC Server in your PC application and how the PC application reacts to the behavior of the OPC Server is not described in this documentation. For more information on this topic, please read the detailed OPC documentation provided by SIMATIC NET. You will find information on the basic aspects of the OPC indicated by the graphic shown below:

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring the OPC Server

3.1

Significance of Configuration

The OPC Server Application Type

The OPC Server can be configured as an interface to all available communication protocols. You can create this object only once in a PC station. You can then use this OPC Server for communication with any number of user programs (OPC clients).

What Can be Configured?

You can configure the following:

(e.g. operator control and monitoring system)

S Protocol and
service-dependent properties

S Properties for specific

connections
Protocol software from

Communications processor from

Standard Situation: Using the default settings

In the simplest case (in other words, the standard situation), you simply need to create the OPC Server in the PC station. You must also create the communications modules used in the station and configure communication connections. The steps are described in detail in Section 2.3 Configuring with SIMATIC NCM PC. If you use the PC Station Wizard, you will be able to put your PC station into operation both quickly and simply.

Using default settings or configured parameters

The parameters you can set with NCM PC all have default settings so that in most cases problem-free communication is possible.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring the OPC Server

3.2

Configuring the Properties of the OPC Server

To check the properties of the OPC Server or to modify parameters, open the Properties dialog of the OPC Server object.

The General tab contains the formal parameters for identifying the OPC Server. In the other tabs, you can make parameter settings for the OPC server related to the specific protocols. These parameters are independent of the communication connections or a DP master system that you configure separately. The table below provides you with an overview of the possible parameter settings depending on the protocol or service type.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring the OPC Server

Table 3-1 Parameter / Function Possible Settings / Significance DP Can be set for a specific protocol FDL (SEND/ RECEIVE) x FMS S7 ISO/TCP (SEND/RE CEIVE) x

Scan cycle time

Here, you make the settings to control updating by the OPC Server. The scan cycle time decides how often the OPC server updates the values of the OPC items.

Access protection

You can specify the access rights to individual variables or variable groups for each specific protocol. You can, for example, prevent variables calculated internally by the controller from being overwritten. As default, no access protection is activated.

VFD

VFD (Virtual Field Device) is the neutral description of a device used in FMS. Communication connections (FMS connections) are then configured for the VFDs. Here, you inform the OPC server of the required VFDs. During configuration, you then assign the VFD to the FMS connection. When accessing variables in the PC application, you also reference the VFD. Extra function: creating the object dictionary Here, you can also create the object dictionary (OD) belonging to a VFD. The FMS variables (name and structure) are defined in the object dictionary.

Connection parameters Segmentation

Here, you can make the settings required for communication for services that do not require specific connection configuration. Special settings for providing the data buffers independent of specific connections.

Please note that the parameters are described in detail in the online help for each individual dialog in NCM PC.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring the OPC Server

3.3

Configuring Connection Properties for the OPC Server

When using OPC, communication connections are established and managed by the OPC Server. As a result, you create the communication connections only for the OPC Server application. How to create a connection for PC applications is described in Section 2.3.5. If a connection is created for the OPC Server, the properties dialog for the connection includes an additional tab, OPC Properties. The dialogs shown below for the various protocols provide you with an overview of the possible settings; in these examples, the parameters have their default settings. Please note that the parameters are described in detail in the online help for each individual dialog in NCM PC.

FDL Connection (SEND/RECEIVE Interface)

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring the OPC Server

FMS Connection

Here, you assign a VFD to the FMS connection; you create VFDs in the properties dialog of the OPC Server. The Options button opens the dialog in which you will find the OPC tab.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring the OPC Server

S7 Connection (S7 Communication)

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Configuring the OPC Server

ISO Transport Connection (SEND/RECEIVE Interface)

ISO-on-TCP Connection (SEND/RECEIVE Interface)

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

4.1

Example of a PROFIBUS Configuration

How does a communication system with PROFIBUS appear?

Below, you will find an example of a communication system using PROFIBUS. Typical communication partners are attached to the PROFIBUS network and they can be reached over the OPC Server.

OPCInterface

Example of a PROFIBUS Configuration

Communication takes place between two devices or modules. Communication in this sense means the transfer of data between two communication partners with different characteristics, controlling the communication partner, and querying the operating state of the partner. Communication with an ET 200 B is described in detail.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

4.2

Quick Start for PROFIBUS Communication with OPC

Introduction
This example illustrates how you can connect an ET 200 B DP slave with a CP 5613 in a PC station over PROFIBUS-DP. This section describes the programs used for configuring a PC station and a DP slave. You will also see how to use the OPC Scout program for communication with the OPC Server.

Requirements
If you want to try out the example yourself, you require the following: S S S S S a PC a communication module for PROFIBUS (CP 5613) the SIMATIC NET CD 07/2001 software an ET 200 B DP slave PROFIBUS cabling between the PC module and ET 200 device

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

4.2.1

Hardware and Software Installation

Installing the Software

Activity 1. 2 3. Turn on the PC and start Windows. Insert the SIMATIC NET 07/2001 CD. If the installation program does not start the CD automatically, start the Setup.exe program on the CD. Follow the on-screen instructions of the installation program. Install the SIMATIC NET software and SIMATIC NCM PC.

Installing the CP 5613

Activity 1. 2. 3. 4. 5. Shut down the PC and turn it off. Disconnect the power cable. Read the instructions for installing cards in the manufacturers instructions for your PC. Insert the CP 5613 module in a PCI slot. Reassemble the PC as described in the instructions of the PC manufacturer and reconnect the power cable.

Attaching to the Network

Activity 1. 2 3. Connect the PROFIBUS cable to the CP 5613. Connect the DP slave to the PROFIBUS cable. Check the terminators on the connectors. The terminators at both ends of the cable must be activated (On).

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

4.2.2

Configuring the PC Station

Basic Configuration of the Installed Module

Activity 1. 2. The welcome page of the Commissioning Wizard opens. Click Next.

3. 4.

Leave the defaults as they are and click Next. On the next page, confirm the configuration of the modules by clicking Next. This saves the configuration and you can no longer go back.

You have now made the following settings in the dialog: S The module will be used for productive communication with the DP protocol. This requires a configuration that will be created with SIMATIC NCM PC or STEP 7. The module will be initialized with the PROFIBUS address 5. This means that it would be possible to download to the PC station over PROFIBUS from an engineering station with SIMATIC NCM PC or STEP 7. In this example, SIMATIC NCM PC is installed locally and a download over the network is not necessary. Index 4 is the identification number for internal addressing of the module within the PC station. Each configured component of a PC station has a unique index. During configuration, the index can be set using SIMATIC STEP 7/HW Config.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

4.2.3

STEP 7 Starting the PC Station Wizard

Specifying the Configuration

Activity 1.

Only click the Next button in the Commissioning Wizard dialog when you have completed the configuration.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

4.2.4

STEP 7 PC Station Wizard: Selecting the Editing Mode

Changing Settings
Activity 1.

Click the Next button.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

4.2.5

STEP 7 PC Station Wizard: Changing Settings

Changing the Hardware and Driver Configuration

Activity 1.

Click the Finish button. This starts HW Config of SIMATIC STEP 7.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

4.2.6

HW Config: Inserting a DP Master System

CP 5613 as DP Master
In the STEP 7 project created by the wizard, a SIMATIC PC station was created automatically as an image of the local PC. This PC station already includes the OPC server as the basic component for productive communication and the CP 5613. You require a DP master system so that you can assign DP slaves. For the DP mode, a DP master system must therefore be added to the CP 5613: Activity 1.

Select the Insert DP Master System menu command.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

4.2.7

HW Config: Inserting a DP Slave

ET 200B as DP Slave
Activity 1. Open the catalog in the right-hand half of the window if it is not already open. You open the catalog by clicking on the following button:

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

4.2.8

HW Config: Downloading the Configuration

Finishing configuration and returning to the Commissioning Wizard

Activity 1. 2. 3. 4. Close HW Config. Activate the Commissioning Wizard dialog box and click the Next button.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

4.2.9

STEP 7 Commissioning Wizard: Specifying the Use of Symbol Files

Completing Commissioning
Activity 1.

2. 3.

Click the Next button. The last dialog box of the Commissioning Wizard appears. Click the Finish button to complete your work with the wizard.

4.2.10

OPC Scout: Establishing a Connection to the OPC Server

The OPC Scout as Client for Commissioning and Testing

You can now access the objects of the programmable controller with any OPC client. The OPC Scout ships with this product as the tool for commissioning and testing. Follow the steps outlined below to set the values of the variables of the DP slave using the OPC Scout:

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

Activity 1. Start the OPC Scout in the Start menu: Start > SIMATIC > SIMATIC NET > PROFIBUS > CP5613_CP5614 > OPC Scout

4.2.11

OPC Scout: Inserting a Group and Variables

Organizing Process Variables

The process variables of the OPC Server (known as OPC items) are assigned to groups. You therefore require an OPC group before you can insert OPC variables. Follow the steps outlined below to create a group and add items to it:

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

Activity 1.

Double-click on the group entry 5613_DP to open the OPC Browser. In the left-hand pane, you will see the hierarchically arranged name space of the OPC variables.

Select the following OPC items from the appropriate branches in the lefthand window and transfer these variables to the right-hand pane by clicking on the arrow button. The structure displayed and the variable names depend on the names specified in the STEP 7 program. DP:[CP_5613]Slave005IB0,2 DP:[CP_5613]Slave005QB0,2 The items are added to the group after you confirm the dialog with OK.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for PROFIBUS-DP

4.2.12

OPC Scout: Displaying and Modifying Values of Variables

Executing Synchronous and Asynchronous Write Jobs

Activity 1.

Now double-click on the Value cell of the output byte with the content {0|0} (first table row). A dialog opens in which you can change the value of a variable.

4. -

Click the OK button to start the write job.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

5.1

Example of an Industrial Ethernet Configuration

How does a communication system with Industrial Ethernet appear?

Below, you will find an example of a communication system using Industrial Ethernet. Typical communication partners are attached to Industrial Ethernet and they can be reached over the OPC Server.

OPCInterface

Example of an Industrial Ethernet Configuration

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

5.2

Quick Start for Industrial Ethernet Communication with OPC

Introduction
This example illustrates how you can connect an S7-400 programmable controller with a PC station over Industrial Ethernet. This section describes the programs used for configuring a PC station for connecting to an S7-400. You will see how symbolic variables in the S7 program are made available in OPC. You will also see how to use the OPC Scout program that is supplied with the product for communication with the OPC Server.

Requirements
If you want to try out the example yourself, you require the following: S S S S S a PC a communication module for Industrial Ethernet (CP 1613) the SIMATIC NET CD 07/2001 software an S7-400 with a CP 443-1 Industrial Ethernet cabling between the PC module and S7 device

For the S7-400, you require an STEP 7 project. In the project, you specify the hardware configuration and the programs and data blocks and define a symbol table. In the example, you will expand your existing STEP 7 project by adding a PC station and will configure the connection between the PC station and the S7-400.

5.2.1

Hardware and Software Installation

Installing the Software

Activity 1. 2 3. 4. Turn on the PC and start Windows. Insert the SIMATIC NET 07/2001 CD. If the installation program does not start the CD automatically, start the Setup.exe program on the CD. Follow the on-screen instructions of the installation program. Once you have completed the installation, the Commissioning Wizard starts automatically.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

Installing the CP 1613

Activity 1. 2. 3. 4. 5. Shut down the PC and turn it off. Disconnect the power cable. Read the instructions for installing cards in the manufacturers instructions for your PC. Insert the CP 1613 module in a PCI slot. Reassemble the PC as described in the instructions of the PC manufacturer and reconnect the power cable.

Attaching to the Network

Activity 1. 2 Connect the Ethernet cable to the CP 1613. Connect the S7-400 device to the network cable.

5.2.2

Configuring the PC Station

Basic Configuration of the Installed Module

Activity 1. The welcome page of the Commissioning Wizard opens. Click Next.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

3. 4.

Leave the defaults as they are and click Next. On the next page, confirm the configuration of the modules by clicking Next. This saves the configuration and you can no longer go back.

You have now made the following settings in the dialog: S S The module will be used for productive communication. This requires a configuration that will be created with SIMATIC NCM PC or STEP 7. The module will be initialized with the MAC address 08.00.06.01.55.06. This means that it would be possible to download to the PC station over Industrial Ethernet from an engineering station with SIMATIC NCM PC or STEP 7. In this example, SIMATIC NCM PC is installed locally and a download over the network is not necessary. Index 4 is the identification number for internal addressing of the module within the PC station. Each configured component of a PC station has a unique index. During configuration, the index can be set using SIMATIC STEP / HW Config.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

5.2.3

STEP 7 Starting the PC Station Wizard

Specifying the Configuration

Activity 1.

Only click the Next button in the Commissioning Wizard dialog when you have completed the configuration.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

5.2.4

STEP 7 PC Station Wizard: Selecting the Editing Mode

Changing Settings
Activity 1.

Click the Next button.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

5.2.5

STEP 7 PC Station Wizard: Opening the Project

Creating a Copy of the Local PC Station

Activity 1.

Click the Next button.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

5.2.6

STEP 7 PC Station Wizard: Changing Settings

Editing the Network and Connection Configuration

Activity 1.

Click the Finish button. This starts NETPRO of STEP 7.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

5.2.7

STEP 7 NetPro

Inserting an S7 Connection
Activity 1.

The S7-400 device is automatically entered as the connection partner and the connection type S7 connection will be set. 3. Confirm this dialog by clicking Apply. You have now configured the connection between the PC station and the S7-400.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

5.2.8

STEP 7 NetPro: Downloading the Configuration

Finishing Configuration and Returning to the Commissioning Wizard

Activity 1. 2. 3. 4. 5. Close NetPro. Activate the Commissioning Wizard dialog box and click the Next button. Select both the PC station and the S7 device by first clicking on the PC station and then on the S7 device while holding down the CTRL key.

5.2.9

STEP 7 Commissioning Wizard

Specifying the Use of Symbol Files

Activity 1.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

2. 3.

Click the Start button to start the Symbol File Configurator. Click the Next button only after the symbol file has been created with the Symbol File Configurator and the file name of the created file has been entered.

5.2.10

Symbol File Configurator

Inserting a New Program

To create a symbol file with the Symbol File Configurator, the programs and therefore the symbol definitions must be selected in a STEP 7 project. The Symbol File Configurator then automatically enters the content of the symbol table and the definition of the data blocks of the STEP 7 program in the file. To insert a program, the corresponding S7 device must be linked to a PC station over an S7 connection as in this example. Activity 1.

The dialog for selecting a new program opens. 2. Select the STEP 7 project in which the program was defined in the left-hand pane of the window. This is a project you created and contains the PC station and the S7-400 device.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

Click the OK button. These symbolic names are now extracted from the STEP 7 project and entered in a symbol file. The dialog is closed and the symbolic name space that has been created is displayed in the main window.

Save the symbol file and close the Symbol File Configurator.

5.2.11

SIMATIC NET Commissioning Wizard

Completing Commissioning
Activity 1. When you closed the Symbol File Configurator, the path to the symbol file was entered in the Symbols dialog of the Commissioning Wizard. Now click the Next button. 2. The last dialog box of the Commissioning Wizard appears. Click the Finish button to complete your work with the wizard.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

5.2.12

OPC Scout: Establishing a Connection to the OPC Server

The OPC Scout as Client for Commissioning and Testing

You can now access the data objects of the S7 station with any OPC client. The OPC Scout ships with this product as the tool for commissioning and testing. Follow the steps outlined below to read the inputs and set the outputs using the OPC Scout: Activity 1. Start the OPC Scout in the Start menu: Start > SIMATIC > SIMATIC NET > Industrial Ethernet > CP1613 > OPC Scout

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

5.2.13

OPC Scout: Inserting a Group and Variables

Organizing Process Variables

Double-click on the group entry IE_SAMPLE to open the OPC Browser. In the left-hand pane, you will see the hierarchically arranged name space of the OPC variables.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

Select the following OPC items from the appropriate branches in the lefthand window and transfer these variables to the right-hand pane by clicking on the arrow button.

Examples: SIMATIC_400(1)_CPU_416-1.Machine Speed SIMATIC_400(1)_CPU_416-1.Machine Start SIMATIC_400(1)_CPU_416-1.Pump1.Flow SIMATIC_400(1)_CPU_416-1.Pump2.Power

The items are added to the group after you confirm the dialog with OK.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Quick Start for the OPC Application for Industrial Ethernet

5.2.14

OPC Scout: Displaying and Modifying Values of Variables

Executing Synchronous Write Jobs

Activity 1.

Now double-click on the Value cell of one of the variables, for example on the 0 of the first OPC item. A dialog opens in which you can change the value of the variable.

4. -

Click the OK button to start the write job.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

SIMATIC NET Support and Training

Customer Support, Technical Support

Open round the clock, worldwide:

Nuremberg Johnson City

Singapore

SIMATIC Hotline Worldwide (Nuremberg) Technical Support (FreeContact)

Local time: Mo.-Fr. 7:00 to 17:00 Phone: Fax: Email: GMT: +49 (180) 5050-222 +49 (180) 5050-223 techsupport@ ad.siemens.de +1:00

Worldwide (Nuremberg) Technical Support

(charged only with SIMATIC Card) Local time: Mo.-Fr. 0:00 to 24:00 Phone: Fax: GMT: +49 (911) 895-7777 +49 (911) 895-7001 +01:00

Europe / Africa (Nuremberg) Authorization

Local time: Mo.-Fr. 7:00 to 17:00 Phone: Fax: Email: GMT: +49 (911) 895-7200 +49 (911) 895-7201 authorization@ nbgm.siemens.de +1:00

America (Johnson City) Technical Support and Authorization

Local time: Mo.-Fr. 8:00 to 19:00 Phone: Fax: Email: GMT: +1 423 461-2522 +1 423 461-2289 simatic.hotline@ sea.siemens.com -5:00

Asia / Australia (Singapore) Technical Support and Authorization

Local time: Mo.-Fr. 8:30 to 17:30 Phone: Fax: Email: GMT: +65 740-7000 +65 740-7001 simatic.hotline@ sae.siemens.com.sg +8:00

The languages spoken on the hotlines are German and English. On the authorization hotline, French, Italian and Spanish are also available.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

SIMATIC NET Support and Training

Training Center
To help you to become familiar with working with SIMATIC S7 PLCs, we offer a range of courses. Please contact your regional training center or the central training center in D 90327 Nuremberg. Tel. + 499118953154 Infoline: Tel. +49 180 523 5611 (48 Pfg./min), Fax. 0180 523 5612 Internet: E-mail: http://www.ad.siemens.de/training [email protected]

Technical Support Online Services

The SIMATIC Customer Support team provides you with comprehensive additional information on SIMATIC products in its online services: S You can obtain the latest information On the Internet at http://www.ad.siemens.de/net Using the Fax-Polling no. 08765-93 02 77 95 00 S Current Product Information leaflets and downloads which you may find useful for your product are available: On the Internet at http://www.ad.siemens.de/csi/net Via the Bulletin Board System (BBS) in Nuremberg (SIMATIC Customer Support Mailbox) at the number +49 (911) 8957100. To access the mailbox, use a modem with V.34 (28.8 Kbps) capability whose parameters you should set as follows: 8, N, 1, ANSI, or dial in using ISDN (x.75, 64 Kbps).

Further Support
If you have further questions about SIMATIC NET products, please contact your local Siemens representative. You will find the addresses: S S In our catalog IK PI On the Internet (http://www.ad.siemens.de)

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Glossary
Station Configuration Editor The Station Configuration Editor is the user interface of the Station Manager; this allows you access to the component management of the PC station. Here, the components are the modules and the applications involved in communications. The Station Configuration Editor can also be used for diagnostic purposes.

Advanced PC Configuration (APC) As of the SIMATIC NET PC/Windows CD 07/2001, a new standard for PC commissioning is available Advanced PC Configuration. Automatic software installation, Plug and Play for all supported modules, and userguided commissioning are also part of Advanced PC Configuration just as greatly simplified OPC configuration and the new SIMATIC NCM PC configuration tool. SIMATIC NCM PC allows configuration of SIMATIC NET PC components that is compatible with STEP 7 and serves as a substitute for the previous PC configuration tools COML S7 and COM PROFIBUS PC Edition. A common database with STEP 7 ensures comprehensive configuration including all protocols.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Glossary

SIMATIC NCM PC SIMATIC NCM PC is a configuration tool that is compatible with STEP 7 and is tailored to the requirements of PC configuration. SIMATIC NCM PC provides the full functionality for the following tasks: Configuring PC stations and networking them graphically Configuring connections Configuring the DP mode (DPV0 and DPV1) Setting network parameters for PROFIBUS Downloading configuration data to PC stations Monitoring communication with attached S7 stations using NCM Diagnostics

Station Manager With the Station Manager, you can configure a PC in much the same way as an S7 station and download the configuration data over the network. The Station Manager is the basic component for configuration and run time of OPC applications.

PC Station In this context, a PC station means a PC with communications modules and applications. The role of this PC might be, for example, to communicate with SIMATIC S7 devices and perform process control tasks. The term runtime station is also used to describe such PCs equipped with runtime software. The PC station is configured for communication with SIMATIC S7 devices in SIMATIC NCM PC / STEP 7. The required runtime software is available on the PC station after installing APC (Advanced PC Configuration).

STEP 7 Project A STEP 7 Project is created with SIMATIC NCM PC or with STEP 7/NCM. It contains the project and configuration data that can be downloaded to S7 stations and PC stations.

SIMATIC NET NCM PC Manual / Quick Start C79000-G8976-C156-01

Connection possibilities for

PG/PC
Overview
Overview

3
CP 5613 (PCI) CP 5613 FO (PCI)

CP 5614 (PCI)

PC card with its own microprocessor Recommended solution for: } PC-based control systems (Soft Control, PLC, Numeric Control, Robot Control) } Process control systems } Human Machine Interface (HMI) } PROFIBUS systems with a large quantity framework (more than 8 stations) } Multi-protocol operation } Use of several CPs in one computer } Versions with Fiber Optic interface (FO)

You will find software for the PC products under Windows on the SIMATIC NET/Windows-CD including the appropriate manuals in pdf format and other detailed information about SIMATIC NET products and communication. The necessary configuration tools are contained in all software packages

CP 5614 FO (PCI)

CP 5511 (PCMCIA)

CP 5611 (PCI)

PC card without its own microprocessor Recommended solution for: } Configuration tools (e.g. STEP 7) } PROFIBUS-DP diagnostics station (e.g. with COM PROFIBUS or as a DP master class 2) } PROFIBUS-DP slave connection } PROFIBUS systems with up to 8 stations } Monoprotocol mode

Fig. 3/102 System interfacing for PG/PC

3/276 Siemens IK PI October 2000

Connection possibilities for

PG/PC
Performance data overview
Performance of the PROFIBUS-CP The maximum data throughput indicates how many digital input/output files can be read or written to or from the PROFIBUS application in 1 ms via the applicable PROFIBUS-CP (regardless of the physical characteristics of the bus).

Performance

G_IK10_deP0035s

CP 5613 1) with DP-RAM access

CP 5613 1) with CP 5412 (A2) with DP-5613/Win NT DP-5412/Win NT

CP 5X11 with SOFTNET-DP

1) The CP 5613 is the successor type to CP 5412 (A2)

Fig. 3/103 Performance in the case of almost equal CPU loading

CPU loading and access time

A comparison of event access (via Interrupt) and polling access shows that the CPU loading in CP 5613 can be reduced considerably using the event/filter mechanism; at the same data throughput.

CPU load

CP 5613 with events via DP-RAM access

Other CPs with polling

G_IK10_deP0036s

CPU load at same data thruput to get current data of a slave

Fig. 3/104 Comparison of CPU loading for event/polling access

Performance data of the PROFIBUS-CP

CP 5613/CP 5613 FO Number of connectable DP slaves No. of parallel FDL tasks to be processed No. of PG/OP and S7 connections No. of FMS connections max. max. max. max. 122 120 501) 402) CP 5614/CP 5614 FO 122 120 501) 402) CP 5412 (A2) 64 118 29 32 CP 5611 60 100 8 CP 5511 60 32 8

Note: The CP 5613 is the successor type to CP 5412 (A2) 1) for credit = 1; PDU size 480 bytes 2) for credit = 1

Siemens IK PI October 2000

3/277

Connection possibilities for

PG/PC
OPC server
Overview OPC servers are supplied with the communication software Standard, open, manufacturer-independent interface Interfacing of OPC-capable Windows applications to S7 communication and S5compatible communication (SEND/RECEIVE). Builds upon software programming interfaces. Efficient data exchange for Windows NT 4.0 and Windows 2000 Pro

PC/Windows NT SIMATIC NET OPC Manager WinCC OPC Client Office 97 OPC Client

FMS OPC Server

DP OPC Server

S7 OPC Server

FMS protocol

DP protocol

S7 communic.

S5 comp. comm. (SEND/RECEIVE)

OPC-Scout with Browser function as OPC-Client and OCX-Data-Control (only S7-OPC server)
FMS-PC SIMATIC S7
0 1

SIMATIC S7

SIMATIC S5 (SEND/RECEIVE only)

ET 200X
G_IK10_deP0040s

SIMATIC S5

PROFIBUS

Ind. Ethernet

S7-PC

Fig. 3/105 System integration with OPC server

Application

Under Windows NT, OPC (OLE for Process Control) can be used as an extension to the communications interfaces COM (Component Object Model) and DCOM (Distributed COM) for the user software. The basic principle of OPC is that OPC client applications can communicate with the OPC server through a standard / open and thus manufacturer-independent interface. Connection to OPC-compatible Windows applications already on the market (Office 97 or HMI systems) is possible.

The following OPC servers are available: PROFIBUS: DP-OPC server for PROFIBUS-DP FMS-OPC server for PROFIBUS-FMS S7-OPC servers for S7 communication, alarms and events as well as S5compatible communication (SEND/RECEIVE) The OPC servers have: Standardized access to SIMATIC S7 and SIMATIC S5 for OPC-compatible applications under Windows NT Consistency between automation products from different manufacturers Efficient data exchange from a process component to a further processing application Simultaneous use of several servers by one client application

The same simple-to-use user interface for different components. Accessibility from every computer in the LAN/WAN High-performance data access via the Custom Interface (C++) Easy to use via the "Automation Interface (VB) or OCX Data Control (S7 and FMS-OPC server only), which is supplied. Grouping of variables (items), whereby a large number of data can be processed in a short time

Functions

Open standardization of addressing using logical names for objects of an automation component or system. Support of symbols from STEP 7

Several clients can run on one OPC server at the same time Server-specific configuration support

3/278 Siemens IK PI October 2000

Connection possibilities for

PG/PC
OPC server
Functions (continued) Interfaces "Custom Interface for high-performance C++ applications "Automation Interface for easy-to-create Visual Basic or similar applications OCX Data Control for embedding directly in COM/ DCOM compatible Windows applications (S7-OPC server and FMS-OPC server only)

Application X

Application Y

WinCC OPC Client

Application X OPC Client

3
Fig. 3/106 Comparison of conventional client/server architecture with an OPC architecture
G_IK10_deP0041s

Server A

Server B

Server C

FMS-OPC Server

S7-OPC Server

XY-OPC Server

DP-OPC Server

Configuration

The communications parameters can be completely configured using the tools in the software which is already installed.

The following demo programs are supplied as standard: For custom interface in C++ For "Automation Interface with Visual Basic Easy integration in the system environment and office applications via C++ and Visual Basic interface Short programming times for applications. Easy to handle and costeffective because the OPC servers are supplied with the communication software

Designed for Industry

Simple use of different networks and protocols through standard interface. Reduced training and learning requirements.

Siemens IK PI October 2000

3/279

Connection possibilities for

PG/PC
OPC server
Technical specifications OPC server
Programming Open and standardized Can be used with different manufacturers systems Variable (item) groups One set of variables, enabling processing of large data volumes in a short time Custom Interface (C++); OPC is therefore powerful Automation Interface (VB, Excel, Access, Delphi, etc.); therefore easy to use Graphics with OCX; allowing configuration instead of programming DP protocol S7 communication FMS protocol S5-compatible communication (SEND/RECEIVE) Windows NT 4.0, 2000 Professional is automatically available for all applications after installation

Product versions
Product DP-5613 S7-5613 FMS-5613 SOFTNET-S7 for PROFIBUS SOFTNET-DP SOFTNET-DP slave CP 5613/5614 and CP 5613 FO/5614 FO with DP-Base software contains OPC servers for: PROFIBUS-DP S7 communication FMS communication S7 communication PROFIBUS-DP PROFIBUS-DP slave S5 compatible communication (FDL) PROFIBUS-DP (master) (in preparation) Access to DP slave of the CP 5614 (in preparation)

Access to

Interfaces

Protocols

Availability

3/280 Siemens IK PI October 2000

Connection possibilities for

PG/PC
CP 5613 communication processor
Overview
DP-M DP-S PG/OP S7 C

PCI card with microprocessor for system interfacing for PCs and SIMATIC programming devices/PC to PROFIBUS up to 12 Mbit/s Communication services: PROFIBUS-DP master according to IEC 61158/ EN 50170 PG/OP communication with STEP 5 and STEP 7. S7 communication S5-compatible communication (SEND/RECEIVE) on the basis of the FDL interface PROFIBUS-FMS according to IEC 61158/ EN 50170 The CP 5613 enables connection to PROFIBUS for SIMATIC PG/PC and PCs with PCI slot under Windows NT 4.0 and Windows 2000 Professional. Short PCI card 9-pin Sub-D socket for connecting to PROFIBUS Diagnostic LEDs. Parallel operation of max. 4 CPs 1) The module is installed via PCI standard mechanisms (plug & play).
1) FMS-5613 supports a maximum 2 CP 5613/5614.

Extensive diagnostic facilities for installation, commissioning and operation of the module High performance via direct Dual Port-RAM-access Event and filter mechanism for relieving the host CPU. OPC servers are supplied with the communication software

S5 C

FMS

OPC

3
It is connected to the optical PROFIBUS with integrated interface and OBT by: bus cable with 2 bus connectors or 830-1T PROFIBUS connecting cable to an optical bus terminal (OBT) for PROFIBUS-DP. Direct connection to the optical PROFIBUS with integrated interface by CP 5613 FO.

Application

The CP 5613 provides high performance support for control tasks on the PC (e.g. PCbased control, numeric control, robot control). It is connected to the electrical PROFIBUS by bus connector and PROFIBUS bus cable or bus terminal (e.g. 12M bus terminal) and PROFIBUS bus cable. It is connected to the optical PROFIBUS by: bus cable with 2 bus connectors or 830-1T PROFIBUS connecting cable to an OLM. Event/filter mechanism The user receives up-to-date data via two access mechanisms: Cyclic polling of the DP slaves (higher load on host CPU) Signalling by new kind of event/filter mode in the event of changes in the input data of a slave (minimum load on host CPU) Both alternatives can be combined. Optimum utilization of the PC is therefore possible for the application in question.

Design

Functions

PROFIBUS-DP Access to process data with DP-Base The CP 5613 is operated as a PROFIBUS-DP master module which holds the process image (input/output and diagnostic data) in the Dual PortRAM (memory area on the CP). The high-performance data exchange with the PROFIBUS slaves is handled independently by the CP 5613 hardware. The user has direct access to the Dual Port-RAM. The process data of the slaves are always consistent, i.e. the user gets the data from one and the same DP cycle. Parallel operation of DP-Base and DP 5613 software is not possible.

The new event/filter mechanism can be used additionally for Signalling by Interrupt for diagnostic messages from slaves In equidistant mode signalling by interrupt: Start DP cycle End of cyclic data exchange with the DP slaves (from hardware version 3, in preparation) Equidistant mode settable as of STEP 7 V5.1

Siemens IK PI October 2000

3/281

Connection possibilities for

PG/PC
CP 5613 communication processor
Functions (continued) FastLogic (rapid shutdown) FastLogic means that the CP 5613 can react automatically to up to 4 plant states. A fast response time and independence of the host application is achieved here, for example, for rapid equipment shutdown. DP programming interface The DP programming interface (DP-Base) of the CP 5613 has the following functions: DP master class 1 including acyclic DP extensions. DP master class 2 (in preparation) incl. acyclic expansions Access to the process data is directly through the Dual PortRAM. The Dual Port-RAM interface not only offers fast access as a DP master but also a basis for portability to other operating system environments (e.g. VXWorks, QNX, RMOS). Via a library (DP_BASE.DLL), administrative functional calls (initialization and management services) are offered. Development Kit DK-5613 The Development Kit DK5613 offers access to the functions DP master class 1 including non-cyclic DP expansions With the software development kit DK-5613 the communication processors CP 5613 and CP 5614 can be integrated in any operating system environments. The kit contains the necessary source code including the descriptions in PDF format and can be downloaded from Internet. Access to process data with DP-5613 The user interface is compatible with software package DP-5412. DP master class 1 The CP 5613 operates as a DP master class 1 according to IEC 61158/EN 50170 and handles data transfer with the distributed stations (DP slaves) completely independently. In a fixed, repetitive message cycle, the central controller exchanges information with the DP slaves (e.g. ET 200S). The DP programming interface (DPLib.DLL) provides the PC programmer with function calls for data transfer. In addition, the DP interface offers the functions SYNC and FREEZE as well as the activation and deactivation of slaves. The DP functional expansions with respect to master class 1 enable non-cyclic read and write functions (DS_READ, DS_WRITE) as well as alarm acknowledgement (ALARM_ACK) to be performed parallel to cyclic data traffic. The non-cyclic transmitted data (e.g. parameterization data) are changed very rarely in comparison with the cyclic measured values and are transmitted with low priority parallel to the fast cyclic useful data transfer. Interrupt acknowledgment in the master ensures reliable transfer of the interrupts from DP slaves (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Parallel operation of DP-Base and DP 5613 software is not possible. DP master class 2 In addition to DP master class 1 services, the CP 5613 also offers DP master class 2 services in connection with the DP programming interface according to IEC 61158/ EN 50170. Devices of this type (programming, configuration or operating devices) are used for commissioning, configuring the DP system or system operation in normal operation (diagnostics). The DP programming interface provides the following services: Master diagnostics Slave diagnostics Read inputs/outputs of a slave Reading configuration data and Changing the slave address. The extended DP functions also include non-cyclic access to the parameters and measured values of a slave (e.g. field devices of the process automation, intelligent HMI devices. This type of slave must be supplied with extensive parameter data during startup and normal operation (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Configuration of PROFIBUSDP takes place with the enclosed COM PROFIBUS PC-Edition. Software for PG/OP communication This software enables programming of the SIMATIC S5/S7 controllers via PROFIBUS in connection with STEP 5/STEP 7. The PG/OP communication for the CP 5613 is already available after installing the CP 5613 (DP-Base). No additional software package is needed. S5-compatible communication (SEND/RECEIVE based on the FDL interface) SEND/RECEIVE (FDL interface) is already available after installation of the CP 5613 (DP-Base) and offers data exchange services for diagnostics and management. No additional software package is needed.

3/282 Siemens IK PI October 2000

Connection possibilities for

PG/PC
CP 5613 communication processor
Functions (continued) Software for S7 communication (S7-5613) The user interface is compatible with software S7-5412. SIMATIC S7 system components communicate with each other via S7 communication. The S7 programming interface enables PG/PC application programs access to SIMATIC S7 system components. The SIMATIC S7 data can be accessed easily and flexibly. The following services are available with S7 communication: Administrative services Link management Mini database Trace. Data transfer services Reading/writing of variables BSEND/BRECEIVE (up to 64 Kbytes per task). Software for PROFIBUS-FMS interface (FMS-5613) The user interface is compatible with software FMS-5412. With the FMS programming interface, AT-compatible PCs can exchange data with FMScapable controllers (e.g. S5/S7) and field devices of other manufacturers. The use of the FMS protocol ensures open communication. The following services are available via the FMS interface: Administrative services CRL management services FMS connection management services Object directory management services for clients and server. Variable services for clients and server (read, write, information report). Server functionality VFD (virtual field device) services for clients and server. Bus access information services (live list). Trace and mini database User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols PROFIBUSDP, S7 communication and PROFIBUS-FMS to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.). Programming interface via C-Library The programming interfaces for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0 For Borland programming interfaces (e.g. DELPHI) partner solutions of AIXO are available. For solutions for other operating systems, see the Development Kit DK-5613.
The DK-5613 can be found in the Internet.

http://www.ad.siemens.de/net/dk5613

Configuration

For all packages mentioned above, the configuration tools are included in the scope of supply.

The complete configuration of the S7 communication is performed using STEP 7 V5.0 SP3 and higher. The configurations generated for the PCs using STEP 7 are stored in files which are subsequently transferred to the individual PCs. Therefore a PROFIBUS network can be started up quickly and easily with a CP 5613.

Configuration of PROFIBUSDP and FMS takes place with the enclosed COM PROFIBUS PC-Edition.

Diagnostics

Extensive diagnostic tools are available (for installation, commissioning and operation) for the module itself and for the PROFIBUS network.

Siemens IK PI October 2000

3/283

Connection possibilities for

PG/PC
CP 5613 communication processor
Designed for Industry Fastest possible access to process data via Dual Port-RAM Short response time with FastLogic Process-consistent data from a DP cycle Higher computing performance in the PC by relieving the host CPU. Fast commissioning by Plug&Play and diagnostic tools Easy portability to other operating systems by a Dual Port-RAM interface Can also be used in a high temperature industrial environment.

Technical specifications
Baud Rates Interfaces Connection to PROFIBUS 9.6 Kbit/s to 12 Mbit/s 9-pin Sub-D socket 5 V DC 5% 1.3 A 6.5 W

Ordering data
DP-5613/Windows NT 4.0, 2000 Pro Software V2.1 for DP protocol on CP 5613/CP 5614/CP 5613 FO/ CP 5614 FO, incl. PG, FDL and DP-OPC server, with electronic manual; on CD-ROM, German/English S7-5613/Windows NT 4.0, 2000 Pro Software V2.1 for S7 communication on CP 5613/CP 5614/CP 5613 FO/ CP 5614 FO, incl. PG, FDL and S7-OPC server, with electronic manual; on CD-ROM, German/English FMS-5613/Windows NT 4.0, 2000 Pro Software V2.1 for FMS protocol on CP 5613/CP 5614/CP 5613 FO/ CP 5614 FO, incl. PG, FDL and FMS-OPC server, with electronic manual; on CD-ROM, German/English Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English PROFIBUS FastConnect RS 485 bus connector Plug 180 With 180 cable outlet

Order No.

6GK1 713-5DB21-3AA0

Supply voltage (from PCI) Power consumption from 5 V Power loss Perm. ambient conditions Operating temperature without fan with fan (air current 0.5 m/s) Transport/storage temperature Relative humidity Design Module format Dimensions (W H) in mm Weight Space required Performance data Single protocol mode Number of connectable DP slaves No. of parallel FDL tasks to be processed No. of PG/OP and S7 connections No. of FMS connections

6GK1 713-5CB21-3AA0

max.

+5 C to +40 C +5 C to +60 C 40 C to +70 C 95% at +25 C PCI card 107 168 250 g 1 PCI slot

6GK1 713-5FB21-3AA0

approx.

max. max. max. max.

122 120 50 1) 402)

1) for credit = 1; PDU size 480 bytes 2) for credit = 1

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 500-0FC00

Ordering data
CP 5613 communication processor

Order No.

6GK1 561-3AA00

} PROFIBUS bus terminal 12M Bus terminal for connecting PROFIBUS stations up to 12 Mbit/s with connecting cable
SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English Electronics manuals Communication systems, protocols, products on CD-ROM German/English

6GK1 500-0AA10

6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

3/284 Siemens IK PI October 2000

Connection possibilities for

PG/PC
CP 5613 FO communication processor
Overview
DP-M DP-S PG/OP S7 C

PCI card with microprocessor for system interfacing for PCs and SIMATIC PUs/PC to the optical PROFIBUS with integrated interface up to 12 Mbit/s Integrated FOC interface for direct FO connection Communication services: PROFIBUS-DP master according to IEC 61158/ EN 50170 PG/OP communication with STEP 5 and STEP 7. S7 communication S5-compatible communication (SEND/RECEIVE) on the basis of the FDL interface PROFIBUS-FMS according to IEC 61158/ EN 50170

Extensive diagnostic facilities for installation, commissioning and operation of the module High performance via direct Dual Port-RAM access Event and filter mechanism for relieving the host CPU. Multiple protocol operation and parallel operation of up to 4 CPs OPC servers are supplied with the communication software

S5 C

FMS

OPC

Application

The CP 5613 FO enables connection to the optical PROFIBUS with integrated interface for SIMATIC PG/PC and PCs with PCI slot under Windows NT 4.0 and Windows 2000 Professional. Short PCI card 2 Duplex sockets for connection of plastic and PCF FOCs with 2 simplex plugs each to the optical PROFIBUS Connection for external power supply. This means data transmission on the optical line is not interrupted when the PC is switched off. PROFIBUS-DP Access to process data with DP-Base The CP 5613 FO is operated as a PROFIBUS-DP master module which holds the process image (input/output and diagnostic data) in the Dual Port-RAM (memory area on the CP). The high-performance data exchange with the PROFIBUS slaves is handled independently by the CP 5613 FO hardware. The user has direct access to the Dual Port-RAM. The process data of the slaves are always consistent, i.e. the user gets the data from one and the same DP cycle. Parallel operation of DP-Base and DP 5613 software is not possible.

The CP 5613 FO provides high performance support for control tasks on the PC (e.g. PC-based control, numeric control, robot control).

Design

Diagnostic LEDs. Parallel operation of up to 4 CPs. The module is installed via PCI standard mechanisms (plug & play).

It is connected to the optical PROFIBUS with integrated interface by: Plastic and PCF FOCs with simplex plugs. It is connected to the electrical PROFIBUS by Plastic and PCF-FOC with simplex plugs to an OBT.

Functions

Event/filter mechanism The user receives up-to-date data via two access mechanisms: Cyclic polling of the DP slaves (higher load on host CPU) Signalling by new kind of event/filter mode in the event of changes in the input data of a slave (minimum load on host CPU) Both alternatives can be combined. Optimum utilization of the PC is therefore possible for the application in question.

The new event/filter mechanism can also be used for: Signalling by Interrupt for diagnostic messages from slaves In equidistant mode signalling by interrupt: Start DP cycle End of cyclic data exchange with the DP slaves (from hardware version 3, in preparation) Equidistant mode settable as of STEP 7 V5.1

Siemens IK PI October 2000

3/285

Connection possibilities for

PG/PC
CP 5613 FO communication processor
Functions (continued) FastLogic (rapid shutdown) FastLogic means that the CP 5613 FO can react automatically to up to 4 plant states. A fast response time and independence of the host application is achieved here, for example, for rapid equipment shutdown. DP programming interface The DP programming interface (DP-Base) of the CP 5613 FO has the following functions: DP master class 1 including acyclic DP extensions. DP master class 2 (in preparation) incl. acyclic expansions Access to the process data is directly through the Dual PortRAM. The Dual Port-RAM interface not only offers fast access as a DP master but also a basis for portability to other operating system environments (e.g. VXWorks, QNX, RMOS). Via a library (DP_BASE.DLL), administrative functional calls (initialization and management services) are offered. Development Kit DK-5613 The Development Kit DK-5613 offers access to the functions DP master class 1 including non-cyclic DP expansions With the software development kit DK-5613 the communication processors CP 5613, CP 5614 and CP 5613 FO/ CP 5614 FO can be integrated in any operating system environments. The kit contains the necessary source code including the descriptions in PDF format and can be downloaded from Internet Access to process data with DP-5613 The user interface is compatible with software package DP-5412. DP master class 1 The CP 5613 FO operates as a DP master class 1 and handles data transfer with the distributed stations (DP slaves) completely independently. In a fixed, repetitive message cycle, the central controller exchanges information with the DP slaves (e.g. ET 200S). The DP programming interface (DPLib.DLL) provides the PC programmer with function calls for data transfer. In addition, the DP interface offers the functions SYNC and FREEZE as well as the activation and deactivation of slaves. The DP functional expansions with respect to master class 1 enable non-cyclic read and write functions (DS_READ, DS_WRITE) as well as alarm acknowledgement (ALARM_ACK) to be performed parallel to cyclic data traffic. The non-cyclic transmitted data (e.g. parameterization data) are changed very rarely in comparison with the cyclic measured values and are transmitted with low priority parallel to the fast cyclic useful data transfer. Interrupt acknowledgment in the master ensures reliable transfer of the interrupts from DP slaves (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Parallel operation of DP-Base and DP 5613 software is not possible. DP master class 2 In addition to DP master class 1 services, the CP 5613 FO also offers DP master class 2 services in connection with the DP programming interface according to IEC 61158/EN 50170. Devices of this type (programming, configuration or operating devices) are used for commissioning, configuring the DP system or system operation in normal operation (diagnostics). The DP programming interface provides the following services: Master diagnostics Slave diagnostics Read inputs/outputs of a slave Reading configuration data and Changing the slave address. The extended DP functions also include non-cyclic access to the parameters and measured values of a slave (e.g. field devices of the process automation, intelligent HMI devices. This type of slave must be supplied with extensive parameter data during startup and normal operation (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Configuration of PROFIBUSDP takes place with the enclosed COM PROFIBUS PC-Edition. Software for PG/OP communication This software enables programming of the SIMATIC S5/S7 controllers via PROFIBUS in connection with STEP 5/STEP 7. The PG/OP communication for the CP 5613 FO is already available after installing the CP 5613 FO (DP-Base). No additional software package is needed. S5-compatible communication (SEND/RECEIVE based on the FDL interface) SEND/RECEIVE (FDL interface) is already available after installation of the CP 5613 FO (DP-Base) and offers data exchange services for diagnostics and management. No additional software package is needed.

3/286 Siemens IK PI October 2000

Connection possibilities for

PG/PC
CP 5613 FO communication processor
Functions (continued) Software for S7 communication (S7-5613) The user interface is compatible with software S7-5412. SIMATIC S7 system components communicate with each other via S7 communication. The S7 programming interface enables PG/PC application programs access to SIMATIC S7 system components. The SIMATIC S7 data can be accessed easily and flexibly. The following services are available with S7 communication: Administrative services Link management Mini database Trace. Data transfer services Reading/writing of variables BSEND/BRECEIVE (up to 64 Kbytes per task). Software for PROFIBUS-FMS interface (FMS-5613) The user interface is compatible with software FMS-5412. With the FMS programming interface, AT-compatible PCs can exchange data with FMScapable controllers (e.g. S5/S7) and field devices of other manufacturers. The use of the FMS protocol ensures open communication. The following services are available via the FMS interface: Administrative services CRL management services FMS connection management services Object directory management services for clients and server. Variable services for clients and server (read, write, information report). Server functionality VFD (virtual field device) services for clients and server. Bus access information services (live list). Trace and mini database User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols PROFIBUSDP, S7 communication and PROFIBUS-FMS to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.). Programming interface via C-Library The programming interfaces for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0 For Borland programming interfaces (e.g. DELPHI) partner solutions of AIXO are available. For solutions for other operating systems, see the Development Kit DK-5613.
The DK-5613 can be found in Internet.

http://www.ad.siemens.de/net/dk5613

Configuration

For all packages mentioned above, the configuration tools are included in the scope of supply. The complete configuration of the S7 communication is performed using STEP 7 V5.1 and higher. Extensive diagnostic tools are available (for installation, commissioning and operation) for the module itself and for the PROFIBUS network. Fastest possible access to process data via Dual Port-RAM Short response time with FastLogic Process-consistent data from a DP cycle

The configurations generated for the PCs using STEP 7 are stored in files which are subsequently transferred to the individual PCs.

Configuration of PROFIBUSDP and FMS takes place with the enclosed COM PROFIBUS PC-Edition.

Diagnostics

Therefore a PROFIBUS network can be started up quickly and easily with a CP 5613 FO.

Designed for Industry

Direct connection to the optical PROFIBUS by integrated FOC interface Higher computing performance in the PC by relieving the host CPU. Fast commissioning by Plug&Play and diagnostic tools

Easy portability to other operating systems by a Dual Port-RAM interface Can also be used in a high temperature industrial environment.

Siemens IK PI October 2000

3/287

Connection possibilities for

PG/PC
CP 5613 FO communication processor
Technical specifications
Baud Rates Interfaces Connection to PROFIBUS External power supply (optical) via standard external power supply Supply voltage from PCI Current consumption from 5 V DC from 12 V DC Power loss Supply voltage (optional) external power supply Current consumption Power loss Perm. ambient conditions Operating temperature without fan with fan (air current 0.5 m/s) Transport/storage temperature Relative humidity Design Module format Dimensions (W H) in mm Weight Space required Performance data Single protocol mode Number of connectable DP slaves No. of parallel FDL tasks to be processed No. of PG/OP and S7 connections No. of FMS connections 9.6 Kbit/s to 12 Mbit/s 2 Duplex socket (FO) Low voltage socket 3.5 mm/1.3 mm + 5 V DC 5% 12 V DC 5% 1.4 A 0.3 A 7W 9 12 V DC 0.4 A 3.6 4.8 W

Ordering data
CP 5613 FO communication processor

Order No.

6GK1 561-3FA00

PCI card for connection to PROFIBUS incl. Windows NT 4.0, 2000 Pro drivers, DP-RAM interface for DP master incl. PG and FDL, configuration software; with electronic manual; on CD-ROM Development Kit 1) DK-5613 Software Development Kit for CP 5613/CP 5614 for integration in any operating system environments on systems with PCI slot DP-5613/Windows NT 4.0, 2000 Pro Software V2.1 for DP protocol on CP 5613/CP 5614/CP 5613 FO/ CP 5614 FO, incl. PG, FDL and DP-OPC server, with electronic manual; on CD-ROM, German/English S7-5613/Windows NT 4.0, 2000 Pro Software V2.1 for S7 communication on CP 5613/CP5614/CP 5613 FO/ CP 5614 FO, incl. PG, FDL and S7-OPC server, with electronic manual; on CD-ROM, German/English FMS-5613/Windows NT 4.0, 2000 Pro Software V2.1 for FMS protocol on CP 5613/CP5614/CP 5613 FO/ CP 5614 FO, incl. PG, FDL and FMS-OPC server, with electronic manual; on CD-ROM, German/English Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English Electronic manuals Communication systems, protocols, products on CD-ROM German/English 1) Download from Internet under:

6GK1 713-5DB21-3AA0

max.

+5 C to +40 C +5 C to +60 C 40 C to +70 C 95% at +25 C PCI card 107 168 250 g 1 PCI slot

6GK1 713-5CB21-3AA0

approx.

max. max. max. max.

122 120 50 1) 40 2)

6GK1 713-5FB21-3AA0

1) for credit = 1; PDU size 480 bytes 2) for credit = 1

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

http://www.ad.siemens.de/net/dk5613

3/288 Siemens IK PI October 2000

Connection possibilities for

PG/PC
CP 5614 communication processor
Overview
DP-M DP-S PG/OP S7 C

PCI card with microprocessor for system interfacing for PCs and SIMATIC programming devices/IPC to PROFIBUS up to 12 Mbit/s Communication services: PROFIBUS-DP master interface according to IEC 61158/EN 50 170 on a PCI card PROFIBUS-DP slave interface according to IEC 61158/EN 50 170 on a PCI card PG/OP communication with STEP 5 and STEP 7. S7 communication

S5-compatible communication (SEND/RECEIVE) on the basis of the FDL interface PROFIBUS-FMS according to IEC 61158/ EN 50170 High performance via direct Dual Port RAM access Event and filter mechanism for relieving the host CPU. OPC servers are supplied with the communication software

S5 C

FMS

OPC

Application

The CP 5614 enables connection to PROFIBUS for SIMATIC PG/PC and PCs with PCI slot under Windows NT 4.0 and Windows 2000 Professional. It can be either a DP master or a DP slave independently of each other. Short PCI card 2 9-pin Sub-D sockets for connecting to PROFIBUS Diagnostic LEDs. Parallel operation of up to 4 CPs. The module is installed via PCI standard mechanisms (plug & play).

This means that two different PROFIBUS networks can be connected to a PC in a hierarchic structure using one PROFIBUS card and data can be exchanged between the networks.

The CP 5614 provides high performance support for control tasks on the PC (e.g. PC based control, numeric control, robot control).

Design

It is connected to the electrical PROFIBUS by bus connector and PROFIBUS bus cable or bus terminal (e.g. 12M bus terminal) and PROFIBUS bus cable. It is connected to the optical PROFIBUS by bus cable with 2 bus connectors or 830-1T PROFIBUS connecting cable to an OLM. Parallel operation of DP 5613 (DP master) and DP-Base (DP master, DP slave) is not possible. Event/filter mechanism The user receives up-to-date data via two access mechanisms: Cyclic polling of the DP slaves (higher load on host CPU) Signalling by new kind of event/filter mode in the event of changes in the input data of a slave (minimum load on host CPU)

It is connected to the optical PROFIBUS with integrated interface and OBT by: bus cable with 2 bus connectors or 830-1T PROFIBUS connecting cable to an optical bus terminal (OBT) for PROFIBUS. Direct connection to the optical PROFIBUS with integrated interface by CP 5614 FO.

Functions

PROFIBUS-DP Access to process data The CP 5614 is operated as a PROFIBUS-DP master and DP slave module which holds the process image (input/output and diagnostic data) in the Dual Port-RAM. The high-performance data exchange with the PROFIBUS slaves is handled independently by the CP 5614 FO hardware. The user has direct access to the Dual Port-RAM. The process data of the slaves are always consistent, i.e. the user gets the data from one and the same DP cycle.

Both alternatives can be combined. Optimum utilization of the PC is therefore possible for the application in question. The new event/filter mechanism can also be used for: Signalling by Interrupt for diagnostic messages from slaves In equidistant mode signalling by interrupt: Start DP cycle End of cyclic data exchange with the DP slaves (from hardware version 3, in preparation) Equidistant mode settable as of STEP 7 V5.1

Siemens IK PI October 2000

3/289

Connection possibilities for

PG/PC
CP 5614 communication processor
Functions (continued) FastLogic (rapid shutdown) FastLogic means that the CP 5614 can react automatically to up to 4 plant states. A fast response time and independence of the host application is achieved here e.g. fast switch off of devices. DP programming interface The DP programming interfaces of the CP 5613 and CP 5614 are identical. The DP programming interface of the CP 5614 has the following functional scope: DP slave DP master class 1 Including acyclic DP extensions. DP master class 2 (in preparation) incl. non-cyclic DP expansions Access to the process data is directly through the Dual PortRAM. The Dual Port-RAM interface not only offers fast access as a DP master/slave but also a basis for portability to other operating system environments (e.g. VXWorks, QNX, RMOS). A DP master and a DP slave library (DP_BASE.DLL or DPS_BASE.DLL) offer administrative function calls (initialization and management services as well as diagnostic functions). A transfer mechanism (application in the PC) can be set by software as a link for data exchange between the master and slave interface. In this manner, defined I/O data can be transferred between the master interface and the slave interface. The two connected PROFIBUS networks can be operated with different PROFIBUS bus parameters due to their mutual independence. Development Kit DK-5613 The Development Kit DK-5613 offers access to the functions DP master class 1 including non-cyclic DP expansions With the software development kit DK-5613 the communication processors CP 5613 and CP 5614 can be integrated in any operating system environments. The kit contains the necessary source code including the descriptions in PDF format and can be downloaded from Internet Access to process data with DP-5613 The user interface is compatible with software package DP-5412. DP master class 1 The CP 5614 operates as a DP master class 1 according to IEC 61158/EN 50170 and handles data transfer with the distributed stations (DP slaves) completely independently. In a fixed, repetitive message cycle, the central controller exchanges information with the DP slaves (e.g. ET 200S). The DP programming interface (DPLib.DLL) provides the PC programmer with function calls for data transfer. In addition, the DP interface offers the functions SYNC and FREEZE as well as the activation and deactivation of slaves. The DP functional expansions with respect to master class 1 enable non-cyclic read and write functions (DS_READ, DS_WRITE) as well as alarm acknowledgement (ALARM_ACK) to be performed parallel to cyclic data traffic. The non-cyclic transmitted data (e.g. parameterization data) are changed very rarely in comparison with the cyclic measured values and are transmitted with low priority parallel to the fast cyclic useful data transfer. Interrupt acknowledgment in the master ensures reliable transfer of the interrupts from DP slaves (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Parallel operation of DP-Base and DP 5613 software is not possible. DP master class 2 In addition to DP master class 1 services, the CP 5614 also offers DP master class 2 services in connection with the DP programming interface according to IEC 61158/ EN 50170. Devices of this type (programming, configuration or operating devices) are used for commissioning, configuring the DP system or system operation in normal operation (diagnostics) The DP programming interface provides the following services: Master diagnostics Slave diagnostics Read inputs/outputs of a slave Reading configuration data and Changing the slave address. The extended DP functions also include non-cyclic access to the parameters and measured values of a slave (e.g. field devices of the process automation, intelligent HMI devices). This type of slave has to be supplied with extensive parameter data during startup and normal operation. (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Configuration of PROFIBUSDP takes place with the enclosed COM PROFIBUS PC-Edition.

3/290 Siemens IK PI October 2000

Connection possibilities for

PG/PC
CP 5614 communication processor
Functions (continued) Software for PG/OP communication This software enables programming of the SIMATIC S5/S7 controllers via PROFIBUS in connection with STEP 5/STEP 7. The PG/OP communication for the CP 5614 is already available after installing the CP 5614 (DP-Base). No additional software package is needed. S5-compatible communication (SEND/RECEIVE based on the FDL interface) SEND/RECEIVE (FDL interface) is already available after installation of the CP 5614 (DP-Base) and offers data exchange services for diagnostics and management. No additional software package is needed. Software for S7 communication (S7-5613) The user interface is compatible with S7-5412. SIMATIC S7 system components communicate with each other via S7 communication. The S7 programming interface enables PG/PC application programs access to SIMATIC S7 system components. The SIMATIC S7 data can be accessed easily and flexibly. The following services are available with S7 communication: Administrative services Link management Mini database Trace. Data transfer services Reading/writing of variables BSEND/BRECEIVE (up to 64 Kbytes per task). Software for PROFIBUS-FMS interface (FMS-5613) The user interface is compatible with software FMS-5412. With the FMS programming interface, AT-compatible PCs can exchange data with FMScapable controllers (e.g. S5/S7) and field devices of other manufacturers. The use of the FMS protocol ensures open communication. The following services are available via the FMS interface: Administrative services CRL management services FMS connection management services Object directory management services for clients and server. Variable services for clients and server (read, write, information report). Server functionality VFD (virtual field device) services for clients and server. Bus access information services (live list). Trace and mini database User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols PROFIBUSDP, S7 communication and PROFIBUS-FMS to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.). Programming interface via C-Library The programming interfaces for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0 For Borland programming interfaces (e.g. DELPHI) partner solutions of AIXO are available. For solutions for other operating systems, see the Development Kit DK-5613.
The DK-5613 can be found in the Internet.

http://www.ad.siemens.de/net/dk5613

Siemens IK PI October 2000

3/291

Connection possibilities for

PG/PC
CP 5614 communication processor
Configuration For all packages mentioned above, the configuration tools are included in the scope of supply. The complete configuration of the S7 communication is performed using STEP 7 V5.0 SP3 and higher. The configurations generated for the PCs using STEP 7 are stored in files which are subsequently transferred to the individual PCs. Therefore a PROFIBUS network can be started up quickly and easily with a CP 5614. Configuration of PROFIBUSDP and FMS takes place with the enclosed COM PROFIBUS PC-Edition.

Diagnostics

Extensive diagnostic tools are available (for installation, commissioning and operation) for the module itself and for the PROFIBUS network. Only 1 slot is required for a master and slave. Fastest possible access to process data via Dual PortRAM Short response time with FastLogic

Designed for Industry

Process-consistent data from a DP cycle Higher computing performance in the PC by relieving the host CPU. Fast commissioning by Plug&Play and diagnostic tools

Easy portability to other operating systems by a Dual Port-RAM interface Can also be used in a high temperature industrial environment.

Programming device with CP 5613

SIMATIC S7-300 with CP 342-5 (DP master)

PROFIBUS
Transfer mechanism DP slave RS 485 DP master CP 5614 Distributed I/O

PROFIBUS

SIMATIC ET 200M

SIMATIC ET 200S

Fig. 3/107 Configuration example with CP 5614

3/292 Siemens IK PI October 2000

G_IK10_deP0110s

Connection possibilities for

PG/PC
CP 5614 communication processor
Technical specifications
Baud Rates Interfaces, connection PROFIBUS-DP master PROFIBUS-DP slave Supply voltage (from PCI) Current consumption from 5 V DC Power loss Perm. ambient conditions Operating temperature without fan with fan (air current 0.5 m/s) Transport/storage temperature Relative humidity Design Module format Dimensions (W H) in mm Weight Space required Performance data Single protocol mode Number of connectable DP slaves Data area of slave interface: input data, output data, diagnostics data No. of parallel FDL tasks to be processed No. of PG/OP and S7 connections No. of FMS connections 9.6 Kbit/s to 12 Mbit/s 9-pin Sub-D socket 9-pin Sub-D socket 5 V DC, 5% approx. approx. 1.6 A 8.0 W

Ordering data
DP-5613/Windows NT 4.0, 2000 Pro Software V2.1 for DP protocol on CP 5613/CP 5614/CP 5613 FO/ CP 5614 FO, incl. PG, FDL and DP-OPC server, with electronic manual; on CD-ROM, German/English S7-5613/Windows NT 4.0, 2000 Pro Software V2.1 for S7 communication on CP 5613/CP5614/CP 5613 FO/ CP 5614 FO, incl. PG, FDL and S7-OPC server, with electronic manual; on CD-ROM, German/English FMS-5613/Windows NT 4.0, 2000 Pro Software V2.1 for FMS protocol on CP 5613/CP5614/CP 5613 FO/ CP 5614 FO, incl. PG, FDL and FMS-OPC server, with electronic manual; on CD-ROM, German/English Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English PROFIBUS FastConnect RS 485 bus connector Plug 180 With 180 cable outlet Order No. 6GK1 561-4AA00

Order No.

6GK1 713-5DB21-3AA0

6GK1 713-5CB21-3AA0

max.

+5 C to +40 C +5 C to +60 C 40 C to +70 C 95% at +25 C PCI card 107 168 300 g 1 PCI slot

6GK1 713-5FB21-3AA0

approx.

max.

122

244 bytes each

max. max. max.

120 50 1) 402)

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 500-0FC00

1) for credit = 1; PDU size 480 bytes 2) for credit = 1

Ordering data

} Communication processor CP 5614 PCI card with master and slave connection to PROFIBUS, incl. Windows NT 4.0, 2000 Pro drivers, DP-RAM Interface for DP master and slave, PG and FDL, configuration software with electronic manual on CD-ROM
Development Kit 1) DK-5613 Software Development Kit for CP 5613/CP 5614 for integration in any operating system environments on systems with PCI slot 1) Download from Internet under:

} PROFIBUS bus terminal 12M Bus terminal for connecting PROFIBUS stations up to 12 Mbit/s with connecting cable
SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server Including manuals, on CD-ROM, German/English Electronic manuals Communication systems, protocols, products on CD-ROM German/English

6GK1 500-0AA10

6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

http://www.ad.siemens.de/net/dk5613

Siemens IK PI October 2000

3/293

Connection possibilities for

PG/PC
CP 5614 FO communication processor
Overview
DP-M DP-S PG/OP S7 C

PCI card with microprocessor for system interfacing for PCs and SIMATIC PUs/PC to the optical PROFIBUS with integrated interface up to 12 Mbit/s Integrated FOC interface for direct FO connection Communication services: PROFIBUS-DP master interface according to IEC 61158/EN 50 170 on a PCI card PROFIBUS-DP slave interface according to IEC 61158/EN 50 170 on a PCI card PG/OP communication with STEP 5 and STEP 7.

S5 C

FMS

OPC

S7 communication S5-compatible communication (SEND/RECEIVE) on the basis of the FDL interface PROFIBUS-FMS according to IEC 61158/ EN 50170 High performance via direct Dual Port RAM access Event and filter mechanism for relieving the host CPU. Multiple protocol operation and parallel operation of up to 4 CPs OPC servers are supplied with the communication software The CP 5614 FO provides high performance support for control tasks on the PC (e.g. PC-based control, numeric control, robot control).

3
Application The CP 5614 FO enables connection to PROFIBUS-DP for SIMATIC PG/PC and AT-compatible PCs with PCI slot under Windows NT 4.0 and Windows 2000 Professional. Design Short PCI card 2 Duplex sockets for connection of plastic and PCF FOCs with 2 simplex plugs each to the optical PROFIBUS 9-pin Sub-D socket for connecting to PROFIBUS Connection for external power supply. This means data transmission on the optical line is not interrupted when the PC is switched off. PROFIBUS-DP Access to process data The CP 5614 is operated as a PROFIBUS-DP master and slave module which holds the process image (input/output and diagnostic data) in the Dual Port-RAM. The high-performance data exchange with the PROFIBUS slaves is handled independently by the CP 5614 FO hardware. The user has direct access to the Dual Port-RAM. The process data of the slaves are always consistent, i.e. the user gets the data from one and the same DP cycle. Parallel operation of DP 5613 (DP master) and DP-Base (DP master, DP slave) is not possible.

It can be either a DP master or a DP slave independently of each other. In this way two different PROFIBUS networks can be connected in a hierarchical structure to one PC with a PROFIBUS card and can exchange data. Diagnostic LEDs. Parallel operation of up to 4 CPs. The software can switch assignment of master and slave to the optical and electrical interface. The module is installed via PCI standard mechanisms (plug & play).

It is connected to the optical PROFIBUS with integrated interface and OBT by: Plastic and PCF FOCs with simplex plugs. It is connected to the electrical PROFIBUS by Plastic and PCF-FOC with simplex plugs to an OBT.

Functions

Signalling by Interrupt for diagnostic messages from slaves In equidistant mode signalling by interrupt: Start DP cycle End of cyclic data exchange with the DP slaves (from hardware version 3, in preparation) Equidistant mode settable as of STEP 7 V5.1 FastLogic (rapid shutdown) FastLogic means that the CP5614 FO can react automatically to up to 4 plant states. A fast response time and independence of the host application is achieved here e.g. fast switch off of devices.

3/294 Siemens IK PI October 2000

Connection possibilities for

PG/PC
CP 5614 FO communication processor
Functions (continued) DP programming interface The DP programming interfaces of the CP 5613 and CP 5614 FO are identical. The DP programming interface of the CP 5614 FO has the following functions: DP slave DP master class 1 including acyclic DP extensions. DP master class 2 (in preparation) incl. non-cyclic expansions Access to the process data is directly through the Dual PortRAM. The Dual Port-RAM interface not only offers fast access as a DP master/slave but also a basis for portability to other operating system environments (e.g. VXWorks, QNX, RMOS). A DP master and a DP slave library (DP_BASE.DLL or DPS_BASE.DLL) offer administrative function calls (initialization and management services as well as diagnostic functions). A transfer mechanism (application in the PC) can be set by software as a link for data exchange between the master and slave interface. In this manner, defined I/O data can be transferred between the master interface and the slave interface. The two connected PROFIBUS networks can be operated with different PROFIBUS bus parameters due to their mutual independence. Development Kit DK-5613 The Development Kit DK-5613 offers access to the functions DP master class 1 including non-cyclic DP expansions. With the software development kit DK-5613 the communication processors CP 5613 and CP 5614 can be integrated in any operating system environments. The kit contains the necessary source code including the descriptions in PDF format and can be downloaded from Internet. Access to process data with DP-5613 The user interface is compatible with software package DP-5412. DP master class 1 The CP 5614 FO operates as a DP master class 1 according to IEC 61158/EN 50170 and handles data transfer with the distributed stations (DP slaves) completely independently. In a fixed, repetitive message cycle, the central controller exchanges information with the DP slaves (e.g. ET 200S). The DP programming interface (DPLib.DLL) provides the PC programmer with function calls for data transfer. In addition, the DP interface offers the functions SYNC and FREEZE as well as the activation and deactivation of slaves. The DP functional expansions with respect to master class 1 enable non-cyclic read and write functions (DS_READ, DS_WRITE) as well as alarm acknowledgement (ALARM_ACK) to be performed parallel to cyclic data traffic. The non-cyclic transmitted data (e.g. parameterization data) are changed very rarely in comparison with the cyclic measured values and are transmitted with low priority parallel to the fast cyclic useful data transfer. Interrupt acknowledgment in the master ensures reliable transfer of the interrupts from DP slaves (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Parallel operation of DP-Base and DP 5613 software is not possible. DP master class 2 In addition to DP master class 1 services, the CP 5614 FO also offers DP master class 2 services in connection with the DP programming interface according to IEC 61158/ EN 50170. Devices of this type (programming, configuration or operating devices) are used for commissioning, configuring the DP system or system operation in normal operation (diagnostics). The DP programming interface provides the following services: Master diagnostics Slave diagnostics Read inputs/outputs of a slave Reading configuration data and Changing the slave address. The extended DP functions also include non-cyclic access to the parameters and measured values of a slave (e.g. field devices of the process automation, intelligent HMI devices. This type of slave has to be supplied with extensive parameter data during startup and normal operation. (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Configuration of PROFIBUSDP takes place with the enclosed COM PROFIBUS PC-Edition.

Siemens IK PI October 2000

3/295

Connection possibilities for

PG/PC
CP 5614 FO communication processor
Functions (continued) Software for PG/OP communication This software enables programming of the SIMATIC S5/S7 controllers via PROFIBUS in connection with STEP 5/STEP 7. The PG/OP communication for the CP 5614 FO is already available after installing the CP 5614 FO (DP-Base). No additional software package is needed. S5-compatible communication (SEND/RECEIVE based on the FDL interface) SEND/RECEIVE (FDL interface) is already available after installation of the CP 5614 FO (DP-Base) and offers data exchange services for diagnostics and management. No additional software package is needed. Software for S7 communication (S7-5613) The user interface is compatible with S7-5412. SIMATIC S7 system components communicate with each other via S7 communication. The S7 programming interface enables PG/PC application programs access to SIMATIC S7 system components. The SIMATIC S7 data can be accessed easily and flexibly. The following services are available with S7 communication: Administrative services Link management Mini database Trace. Data transfer services Reading/writing of variables BSEND/BRECEIVE (up to 64 Kbytes per task). Software for PROFIBUS-FMS interface (FMS-5613) The user interface is compatible with software FMS-5412. With the FMS programming interface, AT-compatible PCs can exchange data with FMScapable controllers (e.g. S5/S7) and field devices of other manufacturers. The use of the FMS protocol ensures open communication. The following services are available via the FMS interface: Administrative services CRL management services FMS connection management services Object directory management services for clients and server. Variable services for clients and server (read, write, information report). Server functionality VFD (virtual field device) services for clients and server. Bus access information services (live list). Trace and mini database User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols PROFIBUSDP, S7 communication and PROFIBUS-FMS to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.). Programming interface via C-Library The programming interfaces for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0 For Borland programming interfaces (e.B. DELPHI) partner solutions of the AIXO Co. are offered. For solutions for other operating systems, see the Development Kit DK-5613.
The DK-5613 can be found in the Internet.

http://www.ad.siemens.de/net/dk5613

3/296 Siemens IK PI October 2000

Connection possibilities for

PG/PC
CP 5614 FO communication processor
Configuration For all packages mentioned above, the configuration tools are included in the scope of supply. The complete configuration of the S7 communication is performed using STEP 7 V5.1 and higher. The configurations generated for the PCs using STEP 7 are stored in files which are subsequently transferred to the individual PCs. Therefore a PROFIBUS network can be started up quickly and easily with a CP 5614 FO. Configuration of PROFIBUSDP and FMS takes place with the enclosed COM PROFIBUS PC-Edition.

Diagnostics

Extensive diagnostic tools are available (for installation, commissioning and operation) for the module itself and for the PROFIBUS network. Only 1 slot is required for a master and slave. Direct connection to the optical PROFIBUS by integrated FOC interface Fastest possible access to process data via Dual PortRAM Short response time with FastLogic

Designed for Industry

Process-consistent data from a DP cycle Higher computing performance in the PC by relieving the host CPU Easy portability to other operating systems by a Dual Port-RAM interface

Can also be used in a high temperature industrial environment Flexible application by switchable assignment of optical and electrical interface to master and slave

Programming device with CP 5613 FO

SIMATIC S7-300 with CP 342-5 FO

optical PROFIBUS
Transfer mechanism DP slave DP master CP 5614 FO Distributed I/O FO RS 485 Switchable

PROFIBUS

SIMATIC ET 200M

SIMATIC ET 200S

Fig. 3/108 Configuration example with CP 5614 FO

Siemens IK PI October 2000

3/297

G_IK10_deP0109s

Connection possibilities for

PG/PC
CP 5614 FO communication processor
Technical specifications
Baud Rates Basic interface setting PROFIBUS master PROFIBUS slave Interfaces switchable by software call PROFIBUS master PROFIBUS slave External power supply (optional) via standard external power supply Supply voltage (from PCI) Current consumption from 5 V DC from 12 V DC Power loss Supply voltage (optional) external power supply Current consumption Power loss Perm. ambient conditions Operating temperature without fan with fan (air current 0.5 m/s) Transport/storage temperature Relative humidity Design Module format Dimensions (W H) in mm Weight Space required Performance data Single protocol mode Number of connectable DP slaves Data area of slave interface: input data, output data, diagnostics data No. of parallel FDL tasks to be processed No. of PG/OP and S7 connections No. of FMS connections 9.6 Kbit/s to 12 Mbit/s 2 Duplex socket (FO) 9-pin Sub-D socket

Ordering data
Development Kit 1) DK-5613 Software Development Kit for CP 5613/CP 5614 for integration in any operating system environments on systems with PCI slot DP-5613/Windows NT 4.0, 2000 Pro Software V2.1 for DP protocol on CP 5613/CP 5614/CP 5613 FO/ CP 5614 FO, incl. PG, FDL and DP-OPC server, with electronic manual; on CD-ROM, German/English S7-5613/Windows NT 4.0, 2000 Pro Software V2.1 for S7 communication on CP 5613/CP 5613 FO/ CP 5614/CP 5614 FO, incl. PG, FDL and S7-OPC server, with electronic manual on CD-ROM, German/English FMS-5613/Windows NT 4.0, 2000 Pro Software V2.1 for FMS protocol on CP 5613/CP 5613 FO/ CP 5614/CP 5614 FO, incl. PG, FDL and FMS-OPC server, with electronic manual on CD-ROM, German/English PROFIBUS FastConnect RS 485 bus connector Plug 180 PROFIBUS bus terminal 12M PROFIBUS plastic fiber optic, simplex plug / polishing set PROFIBUS plastic fiber optic, stripping tool set Connection adapters 50 pieces Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server Including manuals, on CD-ROM, German/English Electronic manuals Communication systems, protocols, products on CD-ROM German/English 1) Download from Internet under:

Order No.

6GK1 713-5DB21-3AA0

9-pin Sub-D socket 2 Duplex socket (FO) Low voltage socket 3.5 mm/1.3 mm + 5 V DC 5% 12 V DC 5% 1.6 A 0.3 A 8W 9 12 V DC 0.4 A 3.6 4.8 W

6GK1 713-5CB21-3AA0

6GK1 713-5FB21-3AA0

max.

+5 C to +40 C +5 C to +60 C 40 C to +70 C 95% at +25 C PCI card 107 168 300 g 1 PCI slot

} } } } }

6GK1 500-0FC00

approx.

6GK1 500-0AA10 6GK1 901-0FB00-0AA0 6GK1 905-6PA10 6ES7 195-1BE00-0XA0

max.

122

244 bytes each

max. max. max.

120 50 1) 40 2)

1) for credit = 1; PDU size 480 bytes 2) for credit = 1

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 704-0AA00-3AA2

Ordering data

Order No. 6GK1 561-4FA00

} CP 5614 FO communication processor PCI card with master and slave connection to PROFIBUS, incl. Windows NT 4.0, 2000 Pro drivers, DP-RAM interface for DP master and slave, configuration software with electronic manual on CD-ROM

6GK1 975-1AA00-3AA0

http://www.ad.siemens.de/net/dk5613

3/298 Siemens IK PI October 2000

Connection possibilities for

PG/PC
CP 5511 communication processor
Overview
DP-M DP-S PG/OP S7 C

For connecting PG/PCs and notebooks with PCMCIA slot to PROFIBUS and MPI of the SIMATIC S7 Communication services: PROFIBUS-DP master class 1 with SOFTNET-DP. PROFIBUS-DP master class 2 including acyclic DP expansions with SOFTNET-DP. PROFIBUS-DP slave with SOFTNET-DP slave. PG/OP communication S7 communication with SOFTNET-S7. S5-compatible communication (SEND/RECEIVE based on the FDL interface) with SOFTNET-DP or SOFTNET-S7. The CP 5511 enables connection of programming devices and AT-compatible PCs to PROFIBUS and to the multipoint interface (MPI) of SIMATIC S7: PCMCIA card type II Adapter with 9-pin Sub-D socket for connection to PROFIBUS The CP 5511 is operated under different software packages and allows the user to execute programming device functions and PC functions via PROFIBUS and the multipoint interface (MPI). Only one CP can be operated for each PG/PC/notebook. Similarly only one protocol (PROFIBUS-DP, S7 communication or FDL) can be used for each CP. The following software packages support the CP 5511: STEP 7 as of V3.2 Drivers for the CP 5511 are supplied with STEP 7 SOFTNET-S7 The S7 programming interface can be used with this package SOFTNET-DP With this the CP 5511 can be used as a PROFIBUS-DP master class 1 or 2 SOFTNET-DP slave for using the CP 5511 as a PROFIBUS-DP slave for connecting PCMCIA slot and notebooks

PCMCIA card type II; for PG/PCs with PCMCIA slot and notebooks Used with: STEP 7, ProTool, Micro/Win, ProTool/Pro, SIMATIC PDM (for PG/OP communication) COM PROFIBUS SOFTNET-S7 (for S7 communication). SOFTNET-DP (for DP). OPC servers are supplied with the communication software

S5 C

FMS

OPC

Application

Design

Functions

COM PROFIBUS as of V3.3 With this package the CP 5511 can be used for commissioning or diagnostics (DP online functions) for PROFIBUS-DP systems STEP 7-Micro/Win as of V2.1 Hardware base for the programming software of the SIMATIC S7-200 programmable controller ProTool, ProTool/PRO The CP 5511 can be used as the hardware basis for the configuration tool for SIMATIC operator panels, touch panels and text displays.

Siemens IK PI October 2000

3/299

Connection possibilities for

PG/PC
CP 5511 communication processor
Designed for Industry Connection for notebooks or other portable PCs to PROFIBUS (e.g. for diagnostics and commissioning) Easy installation and commissioning

Technical specifications
Data transfer rate Interfaces Connection to PROFIBUS Connection to PG/PC 9.6 Kbit/s to 12 Mbit/s 9-pin Sub-D socket PCMCIA slot type II +5 V DC 5% typ. 270 mA, max. 360 mA 1.8 W +5 C to +40 C 20 C to +60 C 95% at +25 C PCMCIA type II 54 85 5 30 g 130 g 1 PCMCIA slot type II

Ordering data
Communication processor CP 5511 PCMCIA card for connecting a PG or PC to PROFIBUS or MPI SOFTNET-S7/Windows 98, NT 4.0, 2000 Pro Software V5.3 for S7 communication incl. FDL and S7-OPC server, with electronic manual on CD-ROM SOFTNET-DP/Windows 98, NT 4.0, 2000 Pro Software V5.3 for DP protocol incl. FDL and DP-OPC server, with electronic manual on CD-ROM SOFTNET-DP slave/Windows 98, NT 4.0, 2000 Pro Software V1.2 for DP slave, incl. OPC server, with electronic manual on CD-ROM PROFIBUS FastConnect RS 485 bus connector Plug 180 With 180 cable outlet Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English Electronics Manuals Communication systems, protocols, products on CD-ROM German/English

Order No.

6GK1 551-1AA00

Supply voltage Current consumption Power loss Perm. ambient conditions Operating temperature Transport/storage temperature Relative humidity

6GK1 704-5CW53-3AA0

6GK1 704-5DW53-3AA0

max.

Design Module format Dimensions (W H D) in mm Weight without adapter approx. with adapter approx. Space required

6GK1 704-5SW12-3AA0

6GK1 500-0FC00

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

3/300 Siemens IK PI October 2000

Connection possibilities for

PG/PC
CP 5611 communication processor
Overview
DP-M DP-S PG/OP S7 C

For connecting PG/PC to PROFIBUS and MPI of the SIMATIC S7 Communication services: PROFIBUS-DP master class 1 with SOFTNET-DP. PROFIBUS-DP master class 2 including acyclic DP expansions with SOFTNET-DP. PROFIBUS-DP slave with SOFTNET-DP slave. PG/OP communication S7 communication with SOFTNET-S7. S5-compatible communication (SEND/RECEIVE on the basis of the FDL interface) with SOFTNET-DP or SOFTNET-S7 The CP 5611 enables the connection of programming devices and PCs to PROFIBUS and multipointcapable MPI interface of the SIMATIC S7. Short PCI card 9-pin Sub-D socket for connection to PROFIBUS The CP 5611 is operated under different software packages and allows the user to execute programming device functions and PC functions via PROFIBUS and the multipoint interface (MPI). Only one CP can be operated for each programming device/PC. Similarly only one protocol (PROFIBUS-DP, S7 communication or FDL) can be used for each CP. The following software packages support the CP 5611: STEP 7 V3.2 upwards under Windows 95 and NT 4.0; Windows 98 from V4.02 and K4.02.5. Drivers for the CP 5611 are included in the scope of supply of STEP 7. SOFTNET-S7 The S7 programming interface can be used with this package SOFTNET-DP With this the CP 5611 can be used as a PROFIBUS-DP master class 1 or 2 SOFTNET-DP slave For using the CP 5611 as a PROFIBUS-DP slave For PUs/PCs with PCI slot.

Short PCI card for programming device / PC with PCI slot. Used with: STEP 7, STEP 7-Micro/Win, ProTool, ProTool/Pro, SIMATIC PDM (for PG/OP communication) COM PROFIBUS SOFTNET-S7 (for S7 communication). SOFTNET-DP (for DP). OPC servers are supplied with the communication software

S5 C

FMS

OPC

Application

Design

Functions

COM PROFIBUS as of V3.3 The CP 5611 can be used with this package for commissioning or diagnostics (DP online functions) for PROFIBUS-DP systems STEP 7-Micro/Win as of V2.1 Hardware base for the programming software of the SIMATIC S7-200 programmable controller ProTool, ProTool/PRO The CP 5611 can be used as the hardware basis for the configuration tool for SIMATIC operator panels, touch panels and text displays.

Siemens IK PI October 2000

3/301

Connection possibilities for

PG/PC
CP 5611 communication processor
Designed for Industry Connection for portable PCs to PROFIBUS (e.g. for diagnostics and commissioning) Easy installation and commissioning

Technical specifications
Data transfer rate Interfaces Connection to PROFIBUS 9.6 Kbit/s to 12 Mbit/s 9-pin Sub-D socket +5 V DC 5% 0.5 A 2.0 W +5 C to +40 C 20 C to +60 C 95% at +25 C PCI card 102 130 100 g 1 PCI slot

Ordering data
CP 5611 communication processor PCI card for connecting a PG or PC to PROFIBUS CP 5611 MPI Consists of PCI card CP 5611 and MPI cable, 5 m SOFTNET-S7/Windows 98, NT4.0, 2000 Pro Software V5.3 for S7 communication incl. FDL and S7-OPC server, with electronic manual on CD-ROM SOFTNET-DP/Windows 98, NT 4.0, 2000 Pro Software V5.3 for DP protocol incl. FDL and DP-OPC server, with electronic manual on CD-ROM SOFTNET-DP slave/Windows 98, NT 4.0, 2000 Pro Software V1.2 for DP slave interface, with electronic manual on CD-ROM PROFIBUS FastConnect RS 485 bus connector Plug 180 With 180 cable outlet

Order No.

6GK1 561-1AA00

Supply voltage Current consumption Power loss Perm. ambient conditions Operating temperature Transport/storage temperature Relative humidity Design Module format Dimensions (H x D) in mm Weight Space required

6GK1 561-1AM00

6GK1 704-5CW53-3AA0

max.

6GK1 704-5DW53-3AA0

approx.

6GK1 704-5SW12-3AA0

6GK1 500-0FC00

} PROFIBUS bus terminal 12M Bus terminal for connecting PROFIBUS stations up to 12 Mbit/s with connecting cable
Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English Electronic manuals Communication systems, protocols, products on CD-ROM German/English

6GK1 500-0AA10

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

3/302 Siemens IK PI October 2000

Connection possibilities for

PG/PC
SOFTNET for PROFIBUS
Overview
DP-M DP-S PG/OP S7 C

CP 5611

CP 5511

PG/PC

SOFTNET for PROFIBUS

S5 C

FMS

OPC

Can be used in conjunction with CP 5511 (PCMCIA), CP 5611 (PCI) and integrated PROFIBUS interface of the SIMATIC PG/PC/PC Communication services: PROFIBUS-DP master class 1 PROFIBUS-DP master class 2 with non-cyclic expansions PROFIBUS-DP slave PG/OP communication S7 communication S5-compatible communication (SEND/RECEIVE based on the FDL interface)

PROFIBUS

S5-115U bis S5-155U with CP 5431 FMS/DP

S7-300 with CP 342-5 or CP 343-5

S7-400 with CP 443-5

G_IK10_deP0039s

Software for linking programmable controllers/PCs and notebooks to automation systems.

Fig. 3/109 System configuration: SOFTNET for PROFIBUS

OPC servers are supplied with the communication software

Application

SOFTNET for PROFIBUS can be used to connect PCs to automation systems, e.g. SIMATIC S7, via PROFIBUS. The following are available as user interfaces:

DP protocol PG/OP communication for SIMATIC S7 S7 communication S5-compatible communication (SEND/RECEIVE based on the FDL interface) This architecture means that, unlike CP 5613 or CP 5614 products the performance capability of the SOFTNET Devices of this type (programming devices, configuration devices or operating devices) are used on startup, on configuring the DP system or for operating the system during normal operation (e.g. diagnostics). The DP programming interface provides the following services: Master diagnostics, slave diagnostics, reading the inputs and outputs of a slave, reading configuration data and changing the slave address. The extended DP functions also include noncyclic access to the parameters and measured values of a slave (e.g. field devices of the process automation, intelligent HMI devices. This type of slave must be supplied with extensive parameter data during startup and normal operation (DS_READ, DS_WRITE, DS_DATA_TRANSPORT).

SOFTNET is available for the following interfaces: CP 5511 (PCMCIA card) CP 5611 (PCI card) Integrated PROFIBUS interfaces of SIMATIC programming devices/PCs. packages depends on the construction and / or the workload of the PCs used.

Principle of operation

SOFTNET processes the complete protocol stack in the PC.

Functions

Software for DP protocol (SOFTNET-DP) DP master class 1 SOFTNET-DP offers DP master class 1 functions in conjunction with the CP 5511 or CP 5611. In a fixed, repetitive message cycle, the central controller exchanges information with the DP slaves (e.g. ET 200S). The DP programming interface (DPLib.DLL) provides the PC programmer with function calls for data transfer. In addition, the DP interface offers the functions SYNC and FREEZE as well as the activation and deactivation of slaves. DP master class 2 In addition to DP master class 1 services, SOFTNETDP also offers DP master class 2 services.

DP slave (SOFTNET-DP slave) A DP slave is an I/O device that reads input information and supplies output information to the I/O. The quantity of input and output information depends on the type of device and can be up to 244 bytes. The slave applications can be implemented on the PC using the functions SET_INPUT and SET_OUTPUT of the slave programming interface. Configuration of PROFIBUSDP takes place with the enclosed COM PROFIBUS PC-Edition. For the slave interface, an example GSD file is provided which can be adapted to the relevant application.

Siemens IK PI October 2000

3/303

Connection possibilities for

PG/PC
SOFTNET for PROFIBUS
Functions (continued) Software for PG/OP communication No special programming packages are required for the CP 5511 and CP 5611 because the drivers are contained in the scope of supply of STEP 7. Programming with STEP 5 is not possible with the CP 5511/CP 5611. Software for S7 communication (SOFTNET-S7) SIMATIC S7 system components communicate with each other via S7 communication. The S7 programming interface enables PG/PC application programs access to SIMATIC S7 system components. The SIMATIC S7 data can be accessed easily and flexibly. The following services are available with S7 communication: Administrative services Link management Mini database Trace. Data transfer services Reading/writing of variables BSEND/BRECEIVE (up to 64 Kbytes per task). The complete configuration of the S7 communication is performed using STEP 7 V5.0 SP3 and higher. The configurations generated for the PCs using STEP 7 are stored in files which are subsequently transferred to the individual PCs. Software for S5-compatible communication (SEND/RECEIVE based on the FDL interface) This layer 2 based interface is used for communication between PG/PC and SIMATIC S5 PG/PC and SIMATIC S7 PG/PC and PG/PC . SEND/RECEIVE offers the following services: Management services Connection establishment services Data transfer services This interface is contained in SOFTNET-DP and SOFTNETS7. Configuration is not necessary. User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols PROFIBUSDP, S7 communication and PROFIBUS-FMS to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.). Programming interface via C-Library The programming interfaces for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ Version 6.0 Microsoft Visual Basic Version 6.0 For Borland programming interfaces (e.g. DELPHI) partner solutions of AIXO are available.

3/304 Siemens IK PI October 2000

Connection possibilities for

PG/PC
SOFTNET for PROFIBUS
Configuration The necessary configuration tools are supplied with the appropriate packages. The complete configuration of the S7 communication is performed using STEP 7 V5.0 ServicePack 3 and higher. Low-cost integration as PROFIBUS-DP master of class 1 or master of class 2 with SOFTNET-DP. as a PROFIBUS-DP slave with SOFTNET-DP slave The configurations generated for the PCs using STEP 7 are stored in files which are subsequently transferred to the individual PCs. Configuration of PROFIBUSDP takes place with the enclosed COM PROFIBUS PC-Edition.

Designed for Industry

to S7 communication with SOFTNET-S7

Performance data: Single protocol operation

CP 5511 Number of connectable DP slaves max. No. of parallel FDL tasks to be processed max. No. of PG/OP and S7 connections max. 60 32 8 CP 5611 60 100 8

Ordering data
DP interface

Order No.

} SOFTNET-DP/Windows 98, NT 4.0, 2000 Pro Software V5.3 for DP protocol incl. FDL protocol and DP-OPC server, with electronic manual on CD-ROM
S7 communication SOFTNET-S7/Windows 98, } NT 4.0, 2000 Pro Software V5.3 for S7 communication incl. FDL protocol and S7-OPC server, with electronic manual on CD-ROM SOFTNET-DP slave/Windows 98, NT 4.0, 2000 Pro Software V1.2 for DP slave interface, with electronic manual on CD-ROM Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English Electronic manuals Communication systems, protocols, products on CD-ROM German/English

6GK1 704-5DW53-3AA0

6GK1 704-5CW53-3AA0

6GK1 704-5SW12-3AA0

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

Siemens IK PI October 2000

3/305

Industrial Ethernet
System interfacing for PG/PC
Overview
System interfacing for PG/PC

CPs with their own microprocessor

CP 1613 (PCI)

You can find software for the PC products under Windows on the SIMATIC NET/Windows CD including the appropriate manuals in pdf format and extensive further information about SIMATIC NET products and communication. The necessary configuring tools are supplied with all software packages.

Protocol software runs on the CP Free PC resources for applications Suitable for extensive applications Recommended for applications with HMI systems with high performance requirements, e.g. WinCC Recommended for largescale systems (5 stations and more, e.g. SIMATIC) Constantly high communication thruput Use for redundant communication Time synchronization

CP 1411 (ISA)

CPs without their own microprocessor

Protocol software runs on the PG/PC PC resources are divided between communication and applications Suitable for less extensive applications Recommended for smaller sytems (up to 4 stations, e.g. SIMATIC) The communication performance depends on PC resources and PC workload

CP 1511 (PCMCIA)

Fig. 4/53 System interfacing for PG/PC

Siemens IK PI October 2000

4/111

Industrial Ethernet
System interfacing for PG/PC
Overview
Data throughput Industrial Ethernet A comparison between CP 1413, CP 1411, CP 1511, CP 1413 (predecessor to CP 1613) and CP 1613 shows the course of the respective communication performance. This course fluctuates in CP 1411 and CP 1511 with the appropriate software packages between 0 and the maximum throughput. Used with software packages, communication performance for the CP 1613 is stable and high, permitting fast response times without fluctuations.

Time
1)

CP 1613 Constantly high communication performance

Mess./sec.

CP 1413 Constant communication performance CP 1411/CP1511 Fluctuating communication performance

G_IK10_deI0037s

1) The CP 1613 is the successormodule to the CP 1413

Fig. 4/54 Comparison of communication performance characteristics

CPU load

The communication must share the PC resources with other applications (especially HMI). In general, therefore, less than 25% of the host CPU time remains available for communication.

Whereas, under these conditions, e.g. the CP 1411/1511 only lets through an average of about 80 messages (with a strongly fluctuating curve), the CP 1613 still offers maximum throughput.

The stated throughput figures represent average values.

Thruput (frames/s)) PC processor performance for communication

100% 75% 50%

Mess./sec.

25%

CPU load

CP 1413

CP 1411 CP 1511

CP 1613

Fig. 4/55 CP 1613 throughput at 20% CPU availability for communication

4/112 Siemens IK PI October 2000

G_IK10_deI0038s

Industrial Ethernet
Introduction
System interfacing for PG/PC; OPC server
Overview OPC servers are contained in the scope of supply of the communication software Standardized, open and vendor-independent interface. Connection of OPC-capable Windows applications to S7 communication and S5compatible communication (SEND/RECEIVE). Builds on the software programming interfaces. Efficient data exchange for Windows NT 4.0 and Windows 2000 Pro
S7-400 FMS-PC SIMATIC S5 (SEND/RECEIVE only)

PC/Windows NT and Windows 2000 Pro SIMATIC NET OPC Manager WinCC OPC Client Office 97 OPC Client

FMS-OPC Server

DP-OPC Server

S7-OPC Server

FMS Protocol

DP Protocol

S7 Communic.

S5 comp. comm. (SEND/RECEIVE)

S7-300

OPC-Scout with browser function as OPC client and OCX data control (only S7 OPC server)

0 1

ET 200X

SIMATIC S5

PROFIBUS

Ind. Ethernet

S7-PC
G_IK10_deI0067s

4
Identical and easy-to-operate user interface for different components. Can be accessed from every computer in the LAN/WAN. High-performance data access via the Custom Interface (C++). Easy to use via the automation interface (VB) or the OCX data control supplied (S7 and FMS OPC server only).

Fig. 4/56 System configuration with OPC server

Application

Under Windows NT and Windows 2000 Professional, OPC (OLE for Process Control) can be used as an extension to the communications interfaces COM (Component Object Model) and DCOM (Distributed COM) for the user software. The basic principle of OPC is that OPC client applications can communicate with the OPC server through a standard/open and thus multi-vendor interface. Facility for linking to existing OPC-capable Windows applications (Office 97 or HMI systems) on the market.

For Industrial Ethernet, the following OPC servers are available: S7 OPC servers for S7 communciation, alarms and events as well as S5-compatible communciation (SEND/RECEIVE) The OPC servers offer the following: Standardized access to SIMATIC S7 and SIMATIC S5 for OPC-capable applications under Windows NT and Windows 2000 Professional Integration between automation products from different manufacturers. Simultaneous utilization of two or more servers by one client application. Simultaneous execution of two or more clients on one OPC server application. Server-specific configuration support. Interfaces Custom interface for high-performance C++ applications.

Functions

Open standardization of addressing via logical names for objects contained in an automation component or automation system. Support of symbols from STEP 7 Efficient data exchange between a process component and a further processing application

Automation interface for easily created Visual Basic or comparable applications. OCX data control for direct integration in Windows applications that support COM/DCOM (S7 OPC server only).

Siemens IK PI October 2000

4/113

Industrial Ethernet
Introduction
System interfacing for PG/PC; OPC server

Application X

Application Y

WinCC OPC Client

Application X OPC Client

Fig. 4/57 Comparison of conventional client/server architecture with an OPC architecture

Configuration

The communications parameters can be completely configured using the tools in the software which is already installed. Different networks and protocols can be easily implemented due to the uniform interface. Low training and familiarization costs.

The following demo programs are included in the scope of supply: For custom interface in C++ Easy integration in the system environment and office applications via C++ and Visual Basic interface Applications can be generated quickly.

For automation interface with Visual Basic.

Designed for Industry

Easy to handle and costeffective because the OPC servers are supplied with the communication software

Technical specifications OPC server

Programming Open and standardized Can be implemented on installations from various manufacturers Groups of variables (items) a set of variables; therefore a large quantity of data can be processed in a short time Custom Interface (C++); making OPC performing Automation interface (VB, Excel, Access, Delphi, ...); therefore easy to use Graphics with OCX; therefore parameterization instead of programming DP protocol. S7 communication FMS protocol S5-compatible communication (SEND/RECEIVE) Windows NT 4.0, 2000 Professional is automatically available for all applications after installation

Product versions
Product S7-1613 TF-1613 SOFTNET-S7 Industrial Ethernet contains OPC servers for: S7 communication S5-compatible communications S5-compatible communications S7 communication

Access to

Interfaces

Protocols

Availability

4/114 Siemens IK PI October 2000

G_IK10_deP0041s

Server A

Server B

Server C

FMS-OPC Server

S7-OPC Server

XY-OPC Server

DP-OPC Server

Industrial Ethernet
System interfacing for PG/PC
CP 1613 communication processor
Overview
ISO TCP/IP PG/OP S7 C

PCI card with microprocessor for connecting PG/PC to Industrial Ethernet with 10/100 Mbit/s autosensing Communication services via ISO or TCP/IP transport protocols PG/OP communication S7 communication S5-compatible communication (SEND/RECEIVE) TF protocol

OPC servers are supplied with the communication software. 15-pin AUI/ITP RJ45 connection ISO and TCP/IP transport protocol onboard Large quantity framework (up to 160 connections with ISO, up to 64 connections with TCP/IP)

S5 C

OPC

Application

The CP 1613 enables connection to Industrial Ethernet (10/100 Mbit/s) for

SIMATIC PG/Industrial PC and PCs with PCI slot.

10 Mbit/s

Triaxial network
Bus connector (Transceiver)

Bus cable 727-0 (triaxial cable) up to 500 m

4
Connecting cable 727-1 (drop cable) up to 50 m CP 1613

10/100 Mbit/s

Twisted Pair Network (Sub-D)

OSM / ESM / OLM / ELM ITP Standard Cable up to 100 m

AUI ITP

RJ45

10/100 Mbit/s
Structured cabling acc. to EN 50173 Twisted Pair Switch (e.g. ESM TP80)

Twisted Pair Network (RJ45)

FC Outlet RJ45

TP Cord RJ45/RJ45 FC Standard Cable TP Cord RJ45/RJ45

G_IK10_deI0051s

Fig. 4/58 Mains connection possibilities CP 1613

Siemens IK PI October 2000

4/115

Industrial Ethernet
System interfacing for PG/PC
CP 1613 communication processor
Design The CP 1613 module (card with microprocessor) is plugged directly into a SIMATIC PG/ PC or a PC and requires a short PCI slot. Connections: 15-pin Sub-D socket for use in industrial applications (automatic switching between AUI, ITP and RJ45 interface) RJ45 for connection in the office environment The module is connected forexample for electrical networks via a 727-1 connecting cable/bus coupler to the 727-0 bus. for ITP via the ITP standard cable 9/15 to OSM/ESM/ star coupler for optical networks via the Mini OTDE optical transceiver. The data transfer between the host system and the CP 1613 is handled by a Windows NT driver or Windows 2000 Pro driver. The transfer rate is detected and automatically switched over (autosensing). Software for PG/OP communication This software permits programming of SIMATIC S5 and S7 PLCs via Industrial Ethernet in combination with STEP 5/STEP 7 automation systems. It is contained in all CP 1613 software packages.

Application

The module independently processes the protocols up to and including level 4 (transport). To permit a large number of connections and high communication integrity, 16 Mbytes of memory are provided. User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols S7 communication and S5compatible communication to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.).

The data exchange between module and host takes place in master mode. This means that the CP 1613 accesses the physical RAM of the host.

Functions

Programming interface via C library The programming interfaces for the protocols S7 communciation, PG/OP communication, S5-compatible communication and TF protocol for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0

4/116 Siemens IK PI October 2000

Industrial Ethernet
System interfacing for PG/PC
CP 1613 communication processor
Functions (continued) Software for S7 communication (S7-1613 or S7-REDCONNECT) The S7 programming interface enables PG/PC applications (e.g. WinCC) and application programs access to SIMATIC S7/M7 system components. Thus, easy and flexible access to the data of the SIMATIC S7/M7 is possible. S7 communication provides: Administrative services Link management. Mini database. Trace. Data transfer services READ/WRITE variables. BSEND/BRECEIVE With S7-REDCONNECT, communication with the highavailability S7-400H system is possible. Software for S5-compatible communication (SEND/RECEIVE) This layer 4 based interface is used for communication between PG/PC and SIMATIC S5 PG/PC and SIMATIC S7 PG/PC and PG/PC . S5-compatible communication (SEND/RECEIVE) provides the following services: Management services Connection buildup service Data transfer services The software is contained in the products S7-1613 and TF-1613. Software for TF protocol (TF-1613) The technological functions interface offers access to the MAP 3.0 open and wellproven automation protocol on Ethernet. The Technological Functions correspond in functionality to the international MMS services in accordance with ISO IS 9506. MMS/TF services: Variable services Domain services Program invocation services General services for virtual devices (VMD support service) Services of TF link management (environment and general management services).
Further details are available in the Internet.

4
http://www.ad.siemens.de/net/ik-info

Configuration

All configuration for S7 communication is performed using STEP 7 V5 upwards.

The configuration settings for PCs made with STEP 7 are stored in files that are then transferred to the individual PCs. Free computer capacity for further applications in the PC, e.g. HMI (ISO and TCP/IP transport onboard) Simple handling through plug & play and autosensing (10/100 Mbit/s). Operation of large network configurations with one card due to large number of connections Can be used for redundant communication OPC as common interface

Designed for Industry

Continuous data throughput through protocol processing on the CP. Can be connected to any Ethernet network via AUI/ITP or RJ45 ports on the module.

Siemens IK PI October 2000

4/117

Industrial Ethernet
System interfacing for PG/PC
CP 1613 communication processor
Technical specifications
Transmission rate Interfaces Connection to Industrial Ethernet (10/100 Mbit/s) 10BaseT, 100BaseTX Supply voltage Current consumption from 5 V DC from 12 V DC Power loss Perm. ambient conditions Operating temperature Transportation/storage temperature Relative humidity max. Construction Module format Dimensions (W D) in mm Weight Space requirements Single protocol mode performance data S7 and PG/OP communication No. of operable connections ISO TCP/IP S5-compatible communication (SEND/RECEIVE) No. of operable connections ISO TCP/IP 10/100 Mbit/s 15-pin Sub-D socket (autom. switching between AUI and twisted pair) RJ45 5 V DC 5% 12 V DC 5% 600 mA 500 mA 4W +5 C to +40 C 20 C to +60 C 95% at +25 C Short AT format 107 167 200 g 1 PCI slot

Ordering data
CP 1613 PCI card for connection to Industrial Ethernet (10/100 Mbit/s) with AUI/ITP and RJ45 port S7-1613/Windows NT 4.0, 2000 Pro V2.1 Software for S7 communication S5-compatible communication (SEND/RECEIVE) and PG/OP communication incl. S7-OPC server for CP 1613 with electronic manual on CD-ROM German/English TF-1613/Windows NT 4.0, 2000 Pro V2.1 Software for TF protocol, S5-compatible communication PG/OP communication for CP 1613 incl. OPC server for S5-compatible communication with electronic manual on CD-ROM German/English PG-1613/Windows NT 4.0, 2000 Pro V2.1 Software for PG/OP communication for CP 1613, with electronic manual on CD-ROM German/English

Order No.

6GK1 161-3AA00

6GK1 716-1CB21-3AA0

6GK1 716-1TB21-3AA0

approx.

6GK1 716-1PB21-3AA0

max. max.

120 120

max. max.

120 120

S7-REDCONNECT/Windows NT 4.0 } V1.3 Software for fail-safe S7 communication via redundant networks for CP 1413, CP 5412 (A2), CP 1613, incl. S7-OPC server with electronic manual on CD-ROM German/English

6GK1 716-0HB13-3AA0

} S7-REDCONNECT/1613 Windows NT 4.0 Upgrade V1.3 Expansion of S7-1613/Windows NT 4.0 to S7-REDCONNECT/Windows NT 4.0 on CD-ROM German/English
Manual: CP 1613 for Industrial Ethernet Hardcopy: contains a description of the interfaces (S7, TF, S5-compatible communication), OPC server, configuring tool for CP 1613 German } English } Electronic Manuals Communications systems, protocols, products on CD-ROM German/English SIMATIC NET Software Update Service for Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English

6GK1 716-0HB13-3AA4

6GK1 971-1GA00-0AA0 6GK1 971-1GA00-0AA1 6GK1 975-1AA00-3AA0

6GK1 704-0AA00-3AA2

4/118 Siemens IK PI October 2000

Industrial Ethernet
System interfacing for PG/PC
S7-REDCONNECT
Overview
ISO TCP/IP PG/OP S7 C
PC with S7-REDCONNECT and 2 x CP 1613

G_IK10_deI0048s

For connection of PCs for redundant Industrial Ethernet to SIMATIC S7-400H For redundantly structured Industrial Ethernet. Operation is also possible in non-redundant networks.

S5 C

OPC
Industrial Ethernet Industrial Ethernet

Completely integrated in STEP 7 from V5.0. OPC servers are supplied with the communications software

S7-400H

Fig. 4/59 System configuration S7-REDCONNECT

Application

The software package S7-REDCONNECT connects the SIMATIC S7-400H to applications on the PC, e.g. WinCC.

Typically, a redundant Industrial Ethernet is used. The software package can also be used where SIMATIC H systems are operated on nonredundant networks. PC with: up to two CP 1613 and S7-REDCONNECT for connecting the PC to Industrial Ethernet with ISO protocol under Windows NT 4.0 Fault detection, switching over if required, communication monitoring and synchronization are handled in the background invisible to the application.

Mixed operation of redundant and non-redundant systems is also possible.

Design

The following components are necessary for assembling a SIMATIC H system with PC connection

S7-400H with: CP 443-1 for connecting the S7-400H to Industrial Ethernet with ISO protocol STEP 7 from V5.0 upwards for configuring. The application, e.g. Win CC, communicates with the 2 subunits of the S7-400H in the same way as with an S7 CPU.

Application

The highly available S7 communication is fed via a master and a reserve connection concealed for the application which is monitored during operation and switched over in the event of a fault. S7-REDCONNECT contains the functional scope of the S7-1613 software package (S7 communication, S5-compatible communication and PG/OP communication) as well as additional redundant communication via S7 connections. An additional licence for S7-1613 is unnecessary. S5-compatible communication Time synchronization. Continuing to use existing Windows applications Services for monitoring the redundant communication. Diagnostics tool for visualizing the communication status

Functions

Programming interface via C library The programming interfaces for the protocols S7 communication, PG/OP communication, S5-compatible communication and TF protocol for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0

Siemens IK PI October 2000

4/119

Industrial Ethernet
System interfacing for PG/PC
S7-REDCONNECT
Configuration
PC with S7-REDCONNECT and 2 x CP 1613 PC

OSM OSM

S7-300
OSM OSM

10/100 Mbit/s

Third-party system

100 Mbit/s

OSM OSM

S7-400
OSM OSM OSM OSM

H system

S7-400

H system
G_IK10_deI0053s

4
Configuration Designed for Industry

Fig. 4/60 Redundant network with S7-400 H and OSM

The configuration established for the PCs with STEP 7 from V5.0 is written to files and transferred to the PCs. Provides protection against communication failure in the event of a fault in the double bus or in redundant rings. Simplifies communication of a PC application with the SIMATIC S7-400H system. Safeguards previous investments due to the use of existing applications and the flexible application possibilities. No additional programming required for PC and H systems. Increases availability of the PC application (e.g. PC S7) through redundant communication.

Ordering data
S7-REDCONNECT/Windows NT 4.0 } V1.3 Software for fail-safe S7 communication via redundant networks (Industrial Ethernet, PROFIBUS) under Windows NT 4.0, can be operated with CP 5412 (A2) and CP 1613 including S7-OPC server with electronic manual on CD-ROM German/English

Order No. 6GK1 716-0HB13-3AA0

} S7-REDCONNECT/1613/ Windows NT 4.0 Upgrade V1.3 Expansion of S7-1613/Windows NT 4.0 to S7-REDCONNECT/Windows NT 4.0 on CD-ROM German/English

6GK1 716-0HB13-3AA4

4/120 Siemens IK PI October 2000

Industrial Ethernet
System interfacing for PG/PC
CP 1411 communication processor
Overview
ISO TCP/IP PG/OP S7 C

For connecting PG/PC to Industrial Ethernet Communication services via ISO or TCP/IP transport protocols PG/OP communication S7 communication S5-compatible communication (SEND/RECEIVE)

Designed for use in industrial environments. ISA card Interfaces: AUI, Industrial Twisted Pair, RJ45 (for office applications). Plug&Play OPC servers are supplied with the communication software

S5 C

OPC

Application

The CP 1411 is an Ethernet card which can be operated in any programming device/PC with a free ISA slot. 15-pin Sub-D socket for use in industrial applications (automatic switching between AUI or industrial twisted pair) RJ45 interface for connection in the office environment

It is intended for applications in an industrial environment.

The CP 1411 can be operated with all SOFTNET for Industrial Ethernet packages.

Design

With a special controller, the CP 1411 is able to support the plug&play mechanism of the operating system.

There is no need to set jumpers. The configuration is made by software. The settings are resident on the module. Free assignment of the Ethernet address allows the user to make rapid and simple changes for startup or diagnostics. In addition, the protocols for Industrial Ethernet provided by the operating system are also supported. The AUI interface under Windows 2000 Professional is not supported.

Application

The CP 1411 offers the following accesses: Layer 2: Interfacing for PC networks in an industrial environment.

Level 4 and level 7. In conjunction with SOFTNET packages for Industrial Ethernet, the CP 1411 offers low-cost access to Industrial Ethernet, e.g. for SIMATIC S5/S7.

Siemens IK PI October 2000

4/121

Industrial Ethernet
System interfacing for PG/PC
CP 1411 communication processor
Designed for Industry Universal connection possibilities (AUI, ITP or RJ45) Optimized for SOFTNET. Ideal for small installations.

Technical specifications
Transmission rate Interfaces Connection to Industrial Ethernet 10 Mbit/s 15-pin Sub-D socket (autom. switching between AUI and Industrial Ethernet pair) RJ45 +5 V DC 5% 12 V DC 5% approx. max. 100 mA 500 mA 0.5 W +5 C to +40 C 40 C to +70 C 95% at +25 C Short AT format 107 15 100 g 1 ISA slot

Ordering data
CP 1411 ISA card for connecting a PG/PC to Industrial Ethernet

Order No.

6GK1 141-1AA00

Connection to 10BaseT Supply voltage Current consumption from 5 V DC from 12 V DC Power loss

Perm. ambient conditions Operating temperature Transportation/storage temperature Relative humidity max. Construction Module format Dimensions (H x D) in mm Weight Space requirements

SOFTNET-S7/Windows 98, NT 4.0, 2000 Pro for Industrial Ethernet V3.3 via ISO or TCP/IP, Software for S5-compatible communication (SEND/RECEIVE) and S7 communication, incl. OPC server, for CP 1411/CP 1511 with electronic manual on CD-ROM German/English Version up to 8 connections (S7) } 6GK1 704-1CW33-3AA0 SOFTNET-PG/Windows 98, } NT 4.0, 2000 Pro for Industrial Ethernet Software V3.3 for PG/OP communication (STEP 5 from V7.1; STEP 7 from V4.02 and K4.02.5), for SIMATIC S5/S7 incl. OPC server, for CP 1411/CP 1511, with electronic manual on CD-ROM German/English SOFTNET Manual for Industrial Ethernet Hardcopy Including: Description of the interfaces (S7, S5-compatible communication), OPC server, configuring tool German } English } SIMATIC NET Software Update Service for Industrial Ethernet, PROFIBUS, OPC server, including manuals on CD-ROM Electronic Manuals Communications systems, protocols, products on CD-ROM German/English 6GK1 704-1PW33-3AA0

approx.

6GK1 971-1EA00-0AA0 6GK1 971-1EA00-0AA1 6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

4/122 Siemens IK PI October 2000

Industrial Ethernet
System interfacing for PG/PC
CP 1511 communication processor
Overview
ISO TCP/IP PG/OP S7 C

For connecting programming devices/ notebooks with PCMCIA slot to Industrial Ethernet Communication services via ISO or TCP/IP transport protocols PG/OP communication S7 communication S5-compatible communication (SEND/RECEIVE)

Designed for use in industrial environments. PCMCIA card type II. Interfaces: Industrial Twisted Pair, RJ45 (for office applications). OPC servers are supplied with the communication software

S5 C

OPC

Application

The CP 1511 is an Ethernet card which can be operated in any programming device/PC with a free PCMCIA type II slot.

In conjunction with all SOFTNET packages for Industrial Ethernet (except UNIX), the CP 1511 can be used e.g. in a programming device 720 for remote programming (PG/OP communication). The CP 1511 can be operated in any computer with a slot complying with the PCMCIA 2.0 standard. There are no jumpers on the module, it can be set completely by software. Level 4 and level 7. In conjunction with the SOFTNET packages for Industrial Ethernet, the CP 1511 offers low-cost access to Industrial Ethernet, e.g. to the SIMATIC S5/S7.

Two adapters are supplied. One adapter is designed for connecting to RJ45, another adapter offers an interface for industrial twisted pair.

4
In addition, the protocols for Industrial Ethernet provided by the operating system are also supported. The CP 1511 is not supported under the Windows 2000 Pro operating system.

Design

PCMCIA card type II. 15-pin Sub-D socket for industrial twisted pair The CP 1511 offers the following accesses: Layer 2: Interfacing for PC networks in an industrial environment.

Application

Siemens IK PI October 2000

4/123

Industrial Ethernet
System interfacing for PG/PC
CP 1511 communication processor
Configurations

Production Level
PC with CP 1613 and WinCC

Control Room
PG/Notebook with CP 1511

S7-400

max. 10 m TP Cord 9 / RJ45 Outlet RJ45

ESM ITP80

ESM

FC Standard Cable

ITP Standard Cable 9/15

Fig. 4/61 System configuration with CP 1511

TP Cord 9 / RJ45

Outlet RJ45

G_IK10_deI0068s

Designed for Industry

Universal connection possibilities (ITP or RJ45) Optimized for SOFTNET.

Ideal for small installations. Use in programming devices/notebooks.

Technical specifications
Transmission rate Interfaces Connection to ITP Connection to 10BaseT Connection to PG/PC Supply voltage Current consumption max. 10 Mbit/s 15-pin Sub-D socket RJ45 PCMCIA slot type II +5 V DC, 5% 0.18 A +5 C to +40 C 20 C to +60 C 90% at +25 C PCMCIA type II 85.6 54 5 approx. 30 g 1 PCMCIA slot type II ITP 60 40 18 100 g 50 cm RJ45 40 22 20 40 g 20 cm

Ordering data

Order No. 6GK1 151-1AA00

} CP 1511 PCMCIA card for the connection of PG/PC to Industrial Ethernet, including 2 adapters for ITP and RJ45
SOFTNET-S7/Windows 98, NT 4.0, 2000 Pro for Industrial Ethernet German/English Version up to 8 connections (S7) SOFTNET-PG/Windows 98, NT 4.0, 2000 Pro for Industrial Ethernet German/English SIMATIC NET Software Update Service for Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English CP 1613 and SOFTNET Manual for Industrial Ethernet Hardcopy German English Electronic Manuals Communications systems, protocols, products on CD-ROM German/English

Perm. ambient conditions Operating temperature Transportation/storage temperature Relative humidity max. Construction of the CP 1511 Module format Dimensions (H W D) in mm Weight Space requirements Construction of adapter Dimensions (H W D) in mm Weight Line length

} }

6GK1 704-1CW33-3AA0 6GK1 704-1PW33-3AA0

6GK1 704-0AA00-3AA2

} } }

6GK1 971-1GA00-0AA0 6GK1 971-1GA00-0AA1 6GK1 975-1AA00-3AA0

4/124 Siemens IK PI October 2000

Industrial Ethernet
System interfacing for PG/PC
SOFTNET for Industrial Ethernet
Overview
ISO TCP/IP PG/OP S7 C
CP 1411 CP 1511 PC/PG SOFTNET for Industrial Ethernet

For connecting programming devices/PCs/ workstations with automation systems. Communication services: PG/OP communication S7 communication S5-compatible communication (SEND/RECEIVE) Can be used in conjunction with CP 1411 (ISA), CP 1511 (PCMCIA). Modem (Remote Access Service RAS)

S5 C

OPC

Industrial Ethernet
S5-115U to -155U with CP 1430 TF S7-400 with CP 443-1
G_IK10_deI0040s

S7-300 with CP 343-1

Complete protocol stack as software package. OPC servers are supplied with the communication software SOFTNET is available for the following interfaces: CP 1411 (ISA card) CP 1511 (PCMCIA card). Modem (RAS) architecture depends on the network extension and/or workload of the PC used. User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols S7 communication and S5-compatible communication to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.). Programming interface via C library The programming interfaces for the protocols S7 communication, PG/OP communication, S5-compatible communication and TF protocol for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0

Fig. 4/62 SOFTNET for Industrial Ethernet system configuration

Application

With SOFTNET for Industrial Ethernet, programming devices/PCs/workstations can be connected to PLCs, e.g. SIMATIC S7, via Industrial Ethernet. The following application interfaces are available: With SOFTNET, the complete protocol stack is handled by the PC. Software for PG/OP communication This software allows programming of the SIMATIC S5 and S7 controllers via Industrial Ethernet in conjunction with STEP 5/STEP 7. Software for S7 communication SIMATIC S7 system components use S7 communication to communicate with each other. To allow programming device/PC user programs to have access to the SIMATIC S7/M7 system components, the S7 programming interface was developed. The S7 communications can optionally be based on the ISO protocol or the TCP/IP protocol. The interface is supplied as a C library or DLL.

PG/OP communication for SIMATIC S7 S5-compatible communication (SEND/RECEIVE) for communication with SIMATIC S7 S7 communication Unlike the 1613 products, the performance capability of the SOFTNET packages with this S7 communication offers the following services: Administrative services S7 connection management services Variables services VFD (virtual field device) services Trace and Mini database. S5-compatible communication (SEND/RECEIVE) This layer 4 based interface (ISO transport or TCP/IP with RFC 1006) is used for communication between PG/PC and SIMATIC S5 PG/PC and SIMATIC S7 PG/PC and PG/PC. S5-compatible communication (SEND/RECEIVE) provides the following services: Management services. Link connection service. Data transfer services

Application

Functions

Siemens IK PI October 2000

4/125

Industrial Ethernet
System interfacing for PG/PC
SOFTNET for Industrial Ethernet
Configuration For the relevant packages the necessary configuring tools are contained in the scope of supply. Communication with SIMATIC via standard Ethernet cards (NE 2000-compatible). Can be used in notebooks with PCMCIA slot. Optimized for small installations.

Designed for Industry

Technical specifications
Performance data S7 and PG/OP communication SOFTNET-S7: Number of operable connections

Ordering data

Order No.

max.

SOFTNET-S7/Windows 98, NT 4.0, 2000 Pro for Industrial Ethernet V3.3 Software for S5-compatible communication (SEND/RECEIVE) and S7 communication, incl. S7-OPC server, for CP 1411/CP 1511 with electronic manual on CD-ROM German/English Version up to 8 connections (S7) } 6GK1 704-1CW33-3AA0 SOFTNET-PG/Windows 98, } NT 4.0, 2000 Pro for Industrial Ethernet Software V3.3 for PG/OP communication (STEP 5 from V7.1; STEP 7 from V4.02 and K4.02.5), for SIMATIC S5/S7, for CP 1411/CP 1511, with electronic manual on CD-ROM German/English CP 1613 and SOFTNET Manual for Industrial Ethernet Hardcopy Including: Description of the interfaces (S7, S5-compatible communication), OPC server, configuring aid German } English } Electronic Manuals Communications systems, protocols, products on CD-ROM German/English SIMATIC NET Software Update Service for Industrial Ethernet, PROFIBUS, OPC server, including manuals on CD-ROM 6GK1 704-1PW33-3AA0

6GK1 971-1GA00-0AA0 6GK1 971-1GA00-0AA1 6GK1 975-1AA00-3AA0

6GK1 704-0AA00-3AA2

4/126 Siemens IK PI October 2000

Connection options for

PG/PC
Overview
Overview

CP 5613 (PCI) CP 5613 FO (PCI)

CP 5614 (PCI)

You will find software for the PC products under Windows on the SIMATIC NET/Windows-CD including the appropriate manuals in pdf format and other detailed information on SIMATIC NET products and communication. The necessary configuration tools are contained in all software packages.

CP 5614 FO (PCI)

CP 5511 (PCMCIA)

CP 5611 (PCI)

Fig. 3/108 System interfacing for PG/PC

Siemens IK PI 2001

3/333

Connection options for

PG/PC
Performance data overview
Performance of the PROFIBUS-CP The maximum data throughput indicates how many digital input/output files can be read or written to or from the PROFIBUS application in 1 ms through the applicable PROFIBUS-CP (regardless of the physical characteristics of the bus).

Performance

3
CPU loading and access time A comparison of event access (through Interrupt) and polling access shows that the CPU loading in CP 5613 can be reduced considerably using the event/filter mechanism; at the same data throughput.

CP 5613 1) with DP-RAM access

CP 5613 1) with CP 5412 (A2) with CP 5X11 with DP-5613/Win NT DP-5412/Win NT SOFTNET-DP

1) The CP 5613 is the successor type to CP 5412 (A2)

Fig. 3/109 Performance in the case of almost equal CPU loading

CPU load

CP 5613 with events through DP-RAM access

Other CPs with polling

G_IK10_deP0036s

CPU load at same data thruput to get current data of a slave

Fig. 3/110 Comparison of CPU loading for event/polling access

Performance data of the PROFIBUS-CP

CP 5613/CP 5613 FO No. of connectable DP slaves No. of parallel FDL tasks to be processed No. of PG/OP and S7 connections No. of FMS connections max. max. max. max. 122 120 501) 402) CP 5614/CP 5614 FO 122 120 501) 402) CP 5412 (A2) 64 118 29 32 CP 5611 60 100 8 CP 5511 60 32 8

Note: The CP 5613 is the successor type to CP 5412 (A2) 1) for credit = 1; PDU size 480 byte 2) for credit = 1

3/334

Siemens IK PI 2001

G_IK10_deP0035s

Connection options for

PG/PC
OPC server
Overview
PC/Windows NT SIMATIC NET OPC-Manager WinCC OPC-Client Office 97 OPC-Client

OPC servers are supplied with the communication software Standard, open, manufacturer-independent interface Interfacing of OPC-capable Windows applications to S7 communication and S5-compatible communication (SEND/RECEIVE). Builds upon software programming interfaces. Efficient data exchange for Windows NT 4.0 and Windows 2000 Pro OPC scout with browser function as OPC client and OCX data control

FMS-OPC-Server

DP-OPC-Server

S7-OPC-Server

FMS protocol

DP protocol

S7 communic.

S5-com. comm. (SEND/RECEIVE)

SIMATIC S7 FMS-PC SIMATIC S7

0 1

SIMATIC S5 (SEND/RECEIVE only)

ET 200X
G_IK10_deP0040s

SIMATIC S5

PROFIBUS

Ind. Ethernet

S7-PC

Fig. 3/111 System integration with OPC server

Application

The same simple-to-use user interface for different components. Accessibility from every computer in the LAN/WAN High-performance data access through the Custom Interface (C++) Easy to use through the Automation Interface (VB) or OCX data control, which is supplied Grouping of variables (items), whereby a large number of data can be processed in a short time

Functions

Open standardization of addressing using logical names for objects of an automation component or system. Support of symbols from STEP 7

Efficient data exchange from a process component to a further processing application Simultaneous use of several servers by one client application

Several clients can run on one OPC server at the same time Server-specific configuration support

Siemens IK PI 2001

3/335

Connection options for

PG/PC
OPC server
Functions (continued)

Interfaces Custom Interface for high-performance C++ applications

Automation Interface for easy-to-create Visual Basic or similar applications

OCX data control for direct integration in Windows applications that support COM/DCOM

Application X

Application Y

WinCC OPC Client

Application X OPC Client

3
Fig. 3/112 Comparison of conventional client/server architecture with an OPC architecture

Configuration

The communications parameters can be completely configured using the tools in the software which is already installed.

The following demo programs are supplied as standard: For custom interface in C++ For Automation Interface with Visual Basic

Other compilers can be implemented through the OPC server, however, the compiler must support the COM interface (Microsoft Component Object Model)

Designed for Industry

Simple use of different networks and protocols through standard interface. Reduced training and learning requirements.

Easy integration in the system environment and office applications through C++ and Visual Basic interface Short programming times for applications.

Easy to handle and costeffective because the OPC servers are supplied with the communication software

3/336

Siemens IK PI 2001

G_IK10_deP0041s

Server A

Server B

Server C

FMS-OPC Server

S7-OPC Server

XY-OPC Server

DP-OPC Server

Connection options for

PG/PC
OPC server
Technical specifications OPC server
Programming

Open and standardized Can be used with different manufacturers systems Variable (item) groups One set of variables, enabling processing of large data volumes in a short time Custom Interface (C++); OPC is therefore powerful Automation Interface (VB, Excel, Access, Delphi, etc.); therefore easy to use Graphics with OCX; allowing configuration instead of programming DP protocol S7 communication FMS protocol S5-compatible communication (SEND/RECEIVE) Windows NT 4.0, 2000 is automatically available for all applications after installation

Access to

Interfaces

Protocols

Availability

Siemens IK PI 2001

3/337

Connection options for

PG/PC
Advanced PC Configuration
Overview Advanced PC Configuration is included in delivery of the communications software from version 6.0 onwards. Simple handling thanks to automatic software installation, Plug & Play and user-prompted commissioning Simple, consistent and costeffective configuration and planning and design of a PC station Considerably simplified OPC configuration Advanced PC Configuration is delivered with the new configuring tool NCM PC and the Startup Wizard and Configuration Console tools.

Application

Advanced PC Configuration represents a new, simple, consistent and cost-effective startup and diagnostics of a PC station. The Startup Wizard, Configuration Console and NCM PC mark the launch of a whole new world of tools.

The Startup Wizard guides the user through all the steps necessary to achieve a ready-to-run PC station The Configuration Console is the central tool for configuration settings and diagnostics

NCM PC V5.1+SP2 offers a new configuring tool for STEP 7-compatible PC configuration

Functions

Startup Wizard Simple and consistent startup of all modules and applications supported by Advanced PC Configuration. A wizard that takes the user step-by-step through the installation and configuration of the PC station.

Configuration Console The Configuration Console is a snap-in embedded in the Microsoft Management Console that offers a range of options for the configuration and diagnostics of PC hardware components and PC applications.

Settings on the OPC servers delivered with the communications software are also executed through the Configuration Console.

3/338

Siemens IK PI 2001

Connection options for

PG/PC
Advanced PC Configuration
Functions (continued) NCM PC NCM PC replaces the previous PC configuration tools COML S7 and COM PROFIBUS PC Edition. In future, PC configuration can be carried out in either STEP 7 or NCM PC, version V5.1+SP2 or higher. Both tools offer the same look & feel and create the same database. This ensures consistent configuration of protocols for S5-compatible communication, S7 communication, DP protocols and FMS protocols. No further need for multiple entries and data consistency is automatically ensured. A configuration wizard integrated in NCM PC also ensures user-prompted configuration of the PC station. With NCM PC and STEP 7, from Version V5.1+SP2, a PC can be configured in the same way as a SIMATIC S7 station and loaded through the network. This applies both to the local station on which NCM PC or STEP 7 is installed and the remote station that is operated through the network.
Note: NCM PC does not contain a conversion for LDBs that were created with COM PROFBUS or COML S7. In this case these must be reconfigured. For further information on Advanced PC Configuration and the previous versions of PC/Windows software products please visit us in the Internet at:

http://www.siemens.de/ simatic-net/ik-info

3
Engineering Station PG/PC with STEP 7 or NCM PC

Advanced PC Configuration

PROFIBUS Industrial Ethernet

S7-400
G_IK10_deP0154s

Runtime PC With application software

Fig. 3/113 PC configuration with STEP 7 or NCM PC

Siemens IK PI 2001

3/339

Connection options for

PG/PC
Advanced PC Configuration
Designed for Industry Simple use of different networks and protocols through standard configuration. Reduced training and learning requirements. Short setting times for communication Uniform procedure and configuration functionality, as for STEP 7

Technical specifications Advanced PC Configuration

Supported modules

Ordering data
Advanced PC Configuration

Order No. Included in delivery are the following products: S7-5613 DP-5613 FMS-5613 SOFTNET-DP slave for PROFIBUS SOFTNET-DP for PROFIBUS SOFTNET-S7 for PROFIBUS SIMATIC NET CD 07/2001 Upgrade

CP 5511, CP 5611, CP 5613, CP 5613 FO, CP 5614, CP 5614 FO CP 5611 compatible PROFIBUS interfaces of PCs/PGs S5-compatible communication S7 communication DP FMS Windows NT 4.0 SP 6a Windows 2000 +SP1 for Professional and servers

Protocols

Operating systems

3/340

Siemens IK PI 2001

Connection options for

PG/PC
CP 5613 communications processor
Overview
DP-M DP-S PG/OP S7 C

PCI card with microprocessor for system interfacing for PCs and SIMATIC programming devices/PC to PROFIBUS up to 12 Mbit/s Communication services: PROFIBUS-DP master according to IEC 61158/ EN 50170 PG/OP communication with STEP 5 and STEP 7 S7 communication S5-compatible communication (SEND/RECEIVE) on the basis of the FDL interface PROFIBUS-FMS according to IEC 61158/EN 50 170 The CP 5613 enables connection to PROFIBUS for SIMATIC PG/PC and PCs with PCI slot under Windows NT 4.0 and Windows 2000. Short PCI card 9-pin Sub-D socket for connecting to PROFIBUS Diagnostic LEDs. Parallel operation of max. 4 CPs 1) The module is installed using PCI standard mechanisms (plug & play).

Extensive diagnostic facilities for installation, commissioning and operation of the module High performance through direct dual port RAMaccess Event and filter mechanism for relieving the host CPU. OPC servers are supplied with the communication software

S5 C

FMS

OPC

3
It is connected to the optical PROFIBUS with integrated interface and OBT through: Bus cable with 2 bus connectors or 830-1T PROFIBUS connecting cable to an optical bus terminal (OBT) for PROFIBUS-DP. Direct connection to the optical PROFIBUS with integrated interface through CP 5613 FO.

Application

The CP 5613 provides high performance support for control tasks on the PC (e.g. PCbased control, numeric control, robot control). It is connected to the electrical PROFIBUS through Bus connector and PROFIBUS bus cable or Bus terminal (e.g. 12M bus terminal) and PROFIBUS bus cable. It is connected to the optical PROFIBUS through: Bus cable with 2 bus connectors or 830-1T PROFIBUS connecting cable to an OLM. Event/filter mechanism The user receives up-to-date data through two access mechanisms: Cyclic polling of the DP slaves (higher load on host CPU) Signaling through new kind of event/filter mode in the event of changes in the input data of a slave (minimum load on host CPU) Both alternatives can be combined. Optimum utilization of the PC is therefore possible for the relevant application.

Design

1) FMS-5613 supports a maximum 2 CP 5613/5614.

Functions

PROFIBUS-DP Access to process data with DP-Base The CP 5613 is operated as a PROFIBUS-DP master module which holds the process image (input/output and diagnostic data) in the dual port RAM (memory area on the CP). The high-performance data exchange with the PROFIBUS slaves is handled independently by the CP 5613 hardware. The user has direct access to the dual port RAM. The process data of the slaves are always consistent, i.e. the user gets the data from one and the same DP cycle. Parallel operation of DP-Base and DP 5613 software is not possible.

The new event/filter mechanism also can be used for Signaling by interrupt for diagnostic messages from slaves In equidistant mode signaling by interrupt: Start DP cycle End of cyclic data exchange with the DP slaves (from hardware version 3, available soon) Equidistant operation adjustable with STEP 7 V5.1 or higher or NCM PC V5.1+SP2.

Siemens IK PI 2001

3/341

Connection options for

PG/PC
CP 5613 communications processor
Functions (continued) FastLogic (rapid shutdown) FastLogic means that the CP 5613 can react automatically to up to 4 plant states. A fast response time and independence of the host application is achieved here, for example, for rapid equipment shutdown. DP programming interface The DP programming interface (DP-Base) of the CP 5613 has the following functions: DP master class 1 including acyclic DP extensions. DP master class 2 (available soon) incl. acyclic expansions Access to the process data is directly through the dual port RAM. The dual port RAM interface not only offers fast access as a DP master but also a basis for portability to other operating system environments (e.g. VXWorks, QNX, RMOS). A library (DP_BASE.DLL) offers administrative functional calls (initialization and management services). Development kit DK-5613 The development kit DK-5613 offers access to the functions DP master class 1 including non-cyclic DP expansions With the software development kit DK-5613 the communications processors CP 5613 and CP 5614 can be integrated in any operating system environments. The kit contains the necessary source code including the descriptions in PDF format and can be downloaded from Internet. Access to process data with DP-5613 The user interface is compatible with software package DP-5412. DP master class 1 The CP 5613 operates as a DP master class 1 according to IEC 61158/EN 50170 and handles data transfer with the distributed stations (DP slaves) completely independently. In a fixed, repetitive message cycle, the central controller exchanges information with the DP slaves (e.g. ET 200S). The DP programming interface (DPLib.DLL) provides the PC programmer with function calls for data transfer. In addition, the DP interface offers the functions SYNC and FREEZE as well as the activation and deactivation of slaves. The DP functional expansions with respect to master class 1 enable non-cyclic read and write functions (DS_READ, DS_WRITE) as well as alarm acknowledgement (ALARM_ACK) to be performed parallel to cyclic data traffic. The non-cyclic transmitted data (e.g. parameterization data) are changed very rarely in comparison with the cyclic measured values and are transmitted with low priority parallel to the fast cyclic useful data transfer. Interrupt acknowledgment in the master ensures reliable transfer of the interrupts from DP slaves (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Parallel operation of DP-Base and DP 5613 software is not possible.

DP master class 2 In addition to DP master class 1 services, the CP 5613 also offers DP master class 2 services in connection with the DP programming interface according to IEC 61158/ EN 50170. Devices of this type (programming, configuration or operating devices) are used for commissioning, configuring the DP system or system operation in normal operation (diagnostics). The DP programming interface provides the following services: Master diagnostics Slave diagnostics Read inputs/outputs of a slave Reading configuration data and Changing the slave address. The extended DP functions also include non-cyclic access to the parameters and measured values of a slave (e.g. field devices of the process automation, intelligent HMI devices. This type of slave must be supplied with extensive parameter data during startup and normal operation (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Software for PG/OP communication This software enables programming of the SIMATIC S5/S7 controllers through PROFIBUS in connection with STEP 5/STEP 7. The PG/OP communication for the CP 5613 is already available after installing the CP 5613 (DP-Base). No additional software package is needed. S5-compatible communication (SEND/RECEIVE based on the FDL interface) SEND/RECEIVE (FDL interface) is already available after installation of the CP 5613 (DP-Base) and offers data exchange services for diagnostics and management. No additional software package is needed.

3/342

Siemens IK PI 2001

Connection options for

PG/PC
CP 5613 communications processor
Functions (continued) Software for S7 communication (S7-5613) The user interface is compatible with software S7-5412. SIMATIC S7 system components communicate with each other through S7 communication. The S7 programming interface enables PG/PC application programs access to SIMATIC S7 system components. The SIMATIC S7 data can be accessed easily and flexibly. The following services are available with S7 communication: Administrative services Link management Mini database Trace. Data transfer services Reading/writing of variables BSEND/BRECEIVE (up to 64 KB per task). Software for PROFIBUS-FMS interface (FMS-5613) The user interface is compatible with software FMS-5412. With the FMS programming interface, AT-compatible PCs can exchange data with FMScapable controllers (e.g. S5/S7) and field devices of other manufacturers. The use of the FMS protocol ensures open communication. The following services are available through the FMS interface: Administrative services CRL management services FMS connection management services Object directory management services for clients and server. Variable services for clients and server (read, write, information report). Server functionality VFD (virtual field device) services for clients and server. Bus access information services (live list). Trace and mini database User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols PROFIBUSDP, S7 communication and PROFIBUS-FMS to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.). Programming interface through C-Library The programming interfaces for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0 Partner solutions from AIXO are available for Borland programming interfaces (e.g. DELPHI). For solutions for other operating systems, see the development kit DK-5613.
The DK-5613 can be found in the Internet at:

http://www.siemens.de/ simatic-net/dk5613

Configuration

Configuration of S7 communication protocols, S5-compatible communication, DP protocol (DP/DPV1/ DPV2) and FMS protocol is executed in STEP 7/NCM PC, V5.1+SP2 or higher.

The configuring tool NCM PC is included in delivery of the PROFIBUS software package.

NCM PC is a component of Advanced PC Configuration.

Diagnosis

Extensive diagnostic tools are available (for installation, commissioning and operation) for the module itself and for the PROFIBUS network.

Therefore a PROFIBUS network can be started up quickly and easily with a CP 5613.

Siemens IK PI 2001

3/343

Connection options for

PG/PC
CP 5613 communications processor
Designed for Industry

Fastest possible access to process data through dual port RAM Short response time with FastLogic Process-consistent data from a DP cycle

Higher computing performance in the PC by relieving the host CPU. Fast commissioning through Plug&Play and diagnostic tools Implementation for motion control applications possible through support of the equidistant mode

Easy portability to other operating systems through a dual port RAM interface Can also be used in high temperature industrial environments.

Technical specifications
Baud rates Interfaces Connection to PROFIBUS 9.6 kbit/s to 12 Mbit/s 9-pin Sub-D socket 5 V DC 5% 1.3 A 6.5 W

Ordering data

Order No. 6GK1 713-5DB60-3AA0

Supply voltage (from PCI) Power consumption from 5 V Power loss Perm. ambient conditions Operating temperature Without fan With fan (air current 0.5 m/s) Transport/storage temperature Relative humidity Design Module format Dimensions (W H) in mm Weight Space required Performance data Single protocol mode No. of connectable DP slaves No. of parallel FDL tasks to be processed No. of PG/OP and S7 connections No. of FMS connections

} DP-5613/Windows V6.0 Software for DP protocol incl. PG/OP communication, FDL, DP-OPC server; NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5613/ CP 5614/CP 5613 FO/CP 5614 FO; with electronic manual; on CD-ROM, in German/English } S7-5613/Windows V6.0 Software for S7 communication incl. PG/OP communication, FDL, S7-OPC server; NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5613/ CP 5614/CP 5613 FO/CP 5614 FO; with electronic manual; on CD-ROM, in German/English } FMS-5613/Windows V6.0 Software for FMS protocol incl. PG/OP communication, FDL, FMS-OPC server; NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5613/ CP 5614/CP 5613 FO/CP 5614 FO; with electronic manual; on CD-ROM, in German/English
Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Paper version Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English PROFIBUS FastConnect RS 485 bus connector Plug 180 With 180 cable outlet

max.

+5 C to +40 C +5 C to +60 C 40 C to +70 C 95% at +25 C PCI card 107 168 250 g 1 PCI slot

6GK1 713-5CB60-3AA0

approx.

6GK1 713-5FB60-3AA0

max. max. max. max.

122 120 50 1) 40 2)

1) For credit = 1; PDU size 480 byte 2) For credit = 1

Ordering data
CP 5613 communications processor PCI card for connection to PROFIBUS incl. Windows NT 4.0 WS, server, Windows 2000 Pro, server driver, DPRAM Interface for DP master incl. PG and FDL, configuration software; with electronic manual; on CD-ROM

Order No.

6GK1 561-3AA00

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 500-0FC00

} PROFIBUS 12M bus terminal Bus terminal for connecting PROFIBUS stations up to 12 Mbit/s with connecting cable
SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English SIMATIC NET Manual Collection Electronic manuals for communication systems, protocols, products on CD-ROM German/English

6GK1 500-0AA10

Development kit DK-5613 Software development kit for CP 5613/CP 5614/CP 5613 FO/ CP 5614 FO for integration in any operating system environments on systems with PCI slot Download from Internet at: http://www.siemens.de/ simatic-net/dk5613

6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

3/344

Siemens IK PI 2001

Connection options for

PG/PC
CP 5613 FO communications processor
Overview
DP-M DP-S PG/OP S7 C

PCI card with microprocessor for system interfacing for PCs and SIMATIC PGs/PC to the optical PROFIBUS with integrated interface up to 12 Mbit/s Integrated FOC interface for direct FO connection Communication services: PROFIBUS-DP master according to IEC 61158/ EN 50170 PG/OP communication with STEP 5 and STEP 7. S7 communication S5-compatible communication (SEND/RECEIVE) on the basis of the FDL interface PROFIBUS-FMS according to IEC 61158/ EN 50170

Extensive diagnostic facilities for installation, commissioning and operation of the module High performance through direct dual port RAM access Event and filter mechanism for relieving the host CPU. Multiple protocol operation and parallel operation of up to 4 CPs OPC servers are supplied with the communication software

S5 C

FMS

OPC

Application

The CP 5613 FO enables connection to the optical PROFIBUS with integrated interface for SIMATIC PG/PC and PCs with PCI slot under Windows NT 4.0 and Windows 2000.

The CP 5613 FO provides high performance support for control tasks on the PC (e.g. PC- based control, numeric control, robot control).

Design

Short PCI card 2 duplex sockets for connection of plastic and PCF FOCs with 2 simplex plugs each to the optical PROFIBUS Connection for external power supply. This means data transmission on the optical line is not interrupted when the PC is switched off.

Diagnostic LEDs. Parallel operation of up to 4 CPs. The module is installed using standard PCI mechanisms (Plug & Play).

It is connected to the optical PROFIBUS with integrated interface through: Plastic and PCF FOCs with simplex plugs. It is connected to the electrical PROFIBUS through Plastic and PCF fiber-optic cable with simplex plugs to an OBT.

Functions

PROFIBUS-DP Access to process data with DP-Base The CP 5613 FO is operated as a PROFIBUS-DP master module which holds the process image (input/output and diagnostic data) in the dual port RAM (memory area on the CP). The high-performance data exchange with the PROFIBUS slaves is handled independently by the CP 5613 FO hardware. The user has direct access to the dual port RAM. The process data of the slaves are always consistent, i.e. the user gets the data from one and the same DP cycle. Parallel operation of DP-Base and DP 5613 software is not possible.

Event/filter mechanism The user receives up-to-date data through two access mechanisms: Cyclic polling of the DP slaves (higher load on host CPU) Signaling by new kind of event/filter mode in the event of changes in the input data of a slave (minimum load on host CPU) Both alternatives can be combined. Optimum utilization of the PC is therefore possible for the relevant application.

The new event/filter mechanism can also be used for: Signaling by interrupt for diagnostic messages from slaves In equidistant mode signaling by interrupt: Start DP cycle End of cyclic data exchange with the DP slaves (from hardware version 3, available soon) Equidistant operation adjustable with STEP 7 V5.1 or higher or NCM PC V5. 1+SP2.

Siemens IK PI 2001

3/345

Connection options for

PG/PC
CP 5613 FO communications processor
Functions (continued) FastLogic (rapid shutdown) FastLogic means that the CP 5613 FO can react automatically to up to 4 plant states. A fast response time and independence of the host application is achieved here, for example, for rapid equipment shutdown. DP programming interface The DP programming interface (DP-Base) of the CP 5613 FO has the following functions: DP master class 1 including acyclic DP extensions. DP master class 2 (available soon) incl. acyclic expansions Access to the process data is directly through the dual port RAM. The dual port RAM interface not only offers fast access as a DP master but also a basis for portability to other operating system environments (e.g. VXWorks, QNX, RMOS). A library (DP_BASE.DLL) offers administrative functional calls (initialization and management services). Development kit DK-5613 The development kit DK-5613 offers access to the functions DP master class 1 including non-cyclic DP expansions With the software development kit DK-5613 the communications processors CP 5613, CP 5614 and CP 5613 FO/CP 5614 FO can be integrated in any operating system environments. The kit contains the necessary source code including the descriptions in PDF format and can be downloaded from the Internet Access to process data with DP-5613 The user interface is compatible with software package DP-5412. DP master class 1 The CP 5613 FO operates as a DP master class 1 and handles data transfer with the distributed stations (DP slaves) completely independently. In a fixed, repetitive message cycle, the central controller exchanges information with the DP slaves (e.g. ET 200S). The DP programming interface (DPLib.DLL) provides the PC programmer with function calls for data transfer. In addition, the DP interface offers the functions SYNC and FREEZE as well as the activation and deactivation of slaves. The DP functional expansions with respect to master class 1 enable non-cyclic read and write functions (DS_READ, DS_WRITE) as well as alarm acknowledgement (ALARM_ACK) to be performed parallel to cyclic data traffic. The non-cyclic transmitted data (e.g. parameterization data) are changed very rarely in comparison with the cyclic measured values and are transmitted with low priority parallel to the fast cyclic useful data transfer. Interrupt acknowledgment in the master ensures reliable transfer of the interrupts from DP slaves (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Parallel operation of DP-Base and DP 5613 software is not possible.

DP master class 2 In addition to DP master class 1 services, the CP 5613 FO also offers DP master class 2 services in connection with the DP programming interface according to IEC 61 158/EN 50170. Devices of this type (programming, configuration or operating devices) are used for commissioning, configuring the DP system or system operation in normal operation (diagnostics). The DP programming interface provides the following services: Master diagnostics Slave diagnostics Read inputs/outputs of a slave Reading configuration data and Changing the slave address. The extended DP functions also include non-cyclic access to the parameters and measured values of a slave (e.g. field devices of the process automation, intelligent HMI devices. This type of slave must be supplied with extensive parameter data during startup and normal operation (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Software for PG/OP communication This software enables programming of the SIMATIC S5/S7 controllers through PROFIBUS in connection with STEP 5/STEP 7. The PG/OP communication for the CP 5613 FO is already available after installing the CP 5613 FO (DP-Base). No additional software package is needed. S5-compatible communication (SEND/RECEIVE based on the FDL interface) SEND/RECEIVE (FDL interface) is already available after installation of the CP 5613 FO (DP-Base) and offers data exchange services for diagnostics and management. No additional software package is needed.

3/346

Siemens IK PI 2001

Connection options for

PG/PC
CP 5613 FO communications processor
Functions (continued) Software for S7 communication (S7-5613) The user interface is compatible with software S7-5412. SIMATIC S7 system components communicate with each other through S7 communication. The S7 programming interface enables PG/PC application programs access to SIMATIC S7 system components. The SIMATIC S7 data can be accessed easily and flexibly. The following services are available with S7 communication: Administrative services Link management Mini database Trace. Data transfer services Reading/writing of variables BSEND/BRECEIVE (up to 64 KB per task). Software for PROFIBUS-FMS interface (FMS-5613) The user interface is compatible with software FMS-5412. The FMS programming interface allows AT-compatible PCs to exchange data with FMS-capable controllers (e.g. S5/S7) and field devices of other manufacturers. The use of the FMS protocol ensures open communication. The following services are available through the FMS interface: Administrative services CRL management services FMS connection management services Object directory management services for clients and server. Variable services for clients and server (read, write, information report). Server functionality VFD (virtual field device) services for clients and server. Bus access information services (live list). Trace and mini database User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols PROFIBUSDP, S7 communication and PROFIBUS-FMS to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.). Programming interface through C-Library The programming interfaces for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0 For Borland programming interfaces (e.g. DELPHI) partner solutions of AIXO are available. For solutions for other operating systems, see the development kit DK-5613.
The DK-5613 can be found in the Internet at:

http://www.siemens.de/ simatic-net/dk5613

Configuration

Configuration of S7 communication protocols, S5-compatible communication, DP protocol (DP/DPV1/ DPV2) and FMS protocol is executed in STEP 7/NCM PC, V5.1+SP2 or higher.

The configuring tool NCM PC is included in delivery of the PROFIBUS software package.

NCM PC is a component of Advanced PC Configuration.

Diagnosis

Extensive diagnostic tools are available (for installation, commissioning and operation) for the module itself and for the PROFIBUS network.

Therefore a PROFIBUS network can be started up quickly and easily with a CP 5613 FO.

Designed for Industry

Fastest possible access to process data through dual port RAM Short response time with FastLogic Process-consistent data from a DP cycle Direct connection to the optical PROFIBUS through integrated FOC interface

Easy portability to other operating systems through a dual port RAM interface Can also be used in high temperature industrial environments.

Siemens IK PI 2001

3/347

Connection options for

PG/PC
CP 5613 FO communications processor
Technical specifications
Baud rates Interfaces Connection to PROFIBUS External power supply (optical) through standard external power supply Supply voltage from PCI Current consumption from 5 V DC from 12 V DC Power loss Supply voltage (optional) external power supply Current consumption Power loss Perm. ambient conditions Operating temperature Without fan With fan (air current 0.5 m/s) Transport/storage temperature Relative humidity Design Module format Dimensions (W H) in mm Weight Space required Performance data Single protocol mode No. of connectable DP slaves No. of parallel FDL tasks to be processed No. of PG/OP and S7 connections No. of FMS connections 9.6 kbit/s to 12 Mbit/s 2 duplex socket (FO) Low voltage socket 3.5 mm/1.3 mm + 5 V DC 5% 12 V DC 5% 1.4 A 0.3 A 7W 9 12 V DC 0.4 A 3.6 4.8 W

Ordering data
CP 5613 FO communications processor PCI card for connection to PROFIBUS-DP incl. Windows NT 4.0 WS, server, Windows 2000 Pro, server driver, DPRAM Interface for DP master incl. PG and FDL, configuration software; with electronic manual; on CD-ROM Development kit 1) DK-5613 Software development kit for CP 5613/CP 5614 for integration in any operating system environments on systems with PCI slot DP-5613/Windows V6.0 } Software for DP protocol incl. PG/OP communication, FDL, DP-OPC server; NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5613/ CP 5614/CP 5613 FO/CP 5614 FO; with electronic manual; on CD-ROM, in German/English

Order No.

6GK1 561-3FA00

6GK1 713-5DB60-3AA0

max.

+5 C to +40 C +5 C to +60 C 40 C to +70 C 95% at +25 C PCI card 107 168 250 g 1 PCI slot

approx.

} S7-5613/Windows V6.0 Software for S7 communication incl. PG/OP communication, FDL, S7-OPC server; NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5613/ CP 5614/CP 5613 FO/CP 5614 FO; with electronic manual; on CD-ROM, in German/English } FMS-5613/Windows V6.0 Software for FMS protocol incl. PG/OP communication, FDL, FMS-OPC server; NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5613/ CP 5614/CP 5613 FO/CP 5614 FO; with electronic manual; on CD-ROM, in German/English
Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Paper version Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English SIMATIC NET Manual Collection Electronic manuals for communication systems, protocols, products on CD-ROM German/English 1) Download from the Internet at

6GK1 713-5CB60-3AA0

6GK1 713-5FB60-3AA0

max. max. max. max.

122 120 50 1) 402)

1) For credit = 1; PDU size 480 byte 2) For credit = 1

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

http://www.siemens.de/simatic-net/dk5613

3/348

Siemens IK PI 2001

Connection options for

PG/PC
CP 5614 communications processor
Overview
DP-M DP-S PG/OP S7 C

S5-compatible communication (SEND/RECEIVE) on the basis of the FDL interface PROFIBUS-FMS according to IEC 61158/ EN 50170 High performance through direct dual port RAMaccess Event and filter mechanism for relieving the host CPU. OPC servers are supplied with the communication software

S5 C

FMS

OPC

Application

The CP 5614 supports connection to PROFIBUS for SIMATIC PG/IPC and PCs with PCI slot under Windows NT 4.0 and Windows 2000, whereby it can operate both as DP master and as DP slave independently of one another. Short PCI card 2 9-pin Sub-D sockets for connecting to PROFIBUS Diagnostic LEDs. Parallel operation of up to 4 CPs. The module is installed using standard PCI mechanisms (plug & play).

This means that two different PROFIBUS networks can be connected to a PC in a hierarchic structure using one PROFIBUS card and data can be exchanged between the networks.

The CP 5614 provides high performance support for control tasks on the PC (e.g. PC based control, numeric control, robot control).

Design

It is connected to the electrical PROFIBUS through Bus connector and PROFIBUS bus cable or Bus terminal (e.g. 12M bus terminal) and PROFIBUS bus cable. It is connected to the optical PROFIBUS through Bus cable with 2 bus connectors or 830-1T PROFIBUS connecting cable to an OLM. Parallel operation of DP 5613 (DP master) and DP-Base (DP master, DP slave) is not possible. Event/filter mechanism The user receives up-to-date data through two access mechanisms: Cyclic polling of the DP slaves (higher load on host CPU) Signaling by new kind of event/filter mode in the event of changes in the input data of a slave (minimum load on host CPU)

It is connected to the optical PROFIBUS with integrated interface and OBT through: Bus cable with 2 bus connectors or 830-1T PROFIBUS connecting cable to an optical bus terminal (OBT) for PROFIBUS. Direct connection to the optical PROFIBUS with integrated interface through CP 5614 FO.

Functions

PROFIBUS-DP Access to process data The CP 5614 is operated as a PROFIBUS-DP master and DP slave module which holds the process image (input/output and diagnostic data) in the dual port RAM. The high-performance data exchange with the PROFIBUS slaves is handled independently by the CP 5614 FO hardware. The user has direct access to the dual port RAM. The process data of the slaves are always consistent, i.e. the user gets the data from one and the same DP cycle.

Both alternatives can be combined. Optimum utilization of the PC is therefore possible for the relevant application. The new event/filter mechanism can also be used for: Signaling by interrupt for diagnostic messages from slaves In equidistant mode signaling by interrupt: Start DP cycle End of cyclic data exchange with the DP slaves (from hardware version 3, available soon) Equidistant operation adjustable with STEP 7 V5.1 or higher or NCM PC V5. 1+SP2.

Siemens IK PI 2001

3/349

Connection options for

PG/PC
CP 5614 communications processor
Functions (continued) FastLogic (rapid shutdown) FastLogic means that the CP 5614 can react automatically to up to 4 plant states. This achieves a fast response time and independence from the host application, e.g. for rapid equipment shutdown. DP programming interface The DP programming interfaces of the CP 5613 and CP 5614 are identical. The DP programming interface of the CP 5614 has the following functional scope: DP slave DP master class 1 including acyclic DP extensions. DP master class 2 (available soon) incl. non-cyclic DP expansions Access to the process data is directly through the dual port RAM. The dual port RAM interface not only offers fast access as a DP master/slave but also a basis for portability to other operating system environments (e.g. VXWorks, QNX, RMOS). A DP master and a DP slave library (DP_BASE.DLL or DPS_BASE.DLL) offer administrative function calls (initialization and management services as well as diagnostic functions). A transfer mechanism (application in the PC) can be set through software as a link for data exchange between the master and slave interface. In this manner, defined I/O data can be transferred between the master interface and the slave interface. The two connected PROFIBUS networks can be operated with different PROFIBUS bus parameters due to their mutual independence. Development kit DK-5613 The development kit DK-5613 offers access to the functions DP master class 1 including non-cyclic DP expansions With the software development kit DK-5613 the communications processors CP 5613 and CP 5614 can be integrated in any operating system environments. The kit contains the necessary source code including the descriptions in PDF format and can be downloaded from the Internet Access to process data with DP-5613 The user interface is compatible with software package DP-5412. DP master class 1 The CP 5614 operates as a DP master class 1 according to IEC 61158/EN 50170 and handles data transfer with the distributed stations (DP slaves) completely independently. In a fixed, repetitive message cycle, the central controller exchanges information with the DP slaves (e.g. ET 200S). The DP programming interface (DPLib.DLL) provides the PC programmer with function calls for data transfer. In addition, the DP interface offers the functions SYNC and FREEZE as well as the activation and deactivation of slaves. The DP functional expansions with respect to master class 1 enable non-cyclic read and write functions (DS_READ, DS_WRITE) as well as alarm acknowledgement (ALARM_ACK) to be performed parallel to cyclic data traffic. The non-cyclic transmitted data (e.g. parameterization data) are changed very rarely in comparison with the cyclic measured values and are transmitted with low priority parallel to the fast cyclic useful data transfer. Interrupt acknowledgment in the master ensures reliable transfer of the interrupts from DP slaves (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Parallel operation of DP-Base and DP 5613 software is not possible.

DP master class 2 In addition to DP master class 1 services, the CP 5614 also offers DP master class 2 services in connection with the DP programming interface according to IEC 61158/ EN 50170. Devices of this type (programming, configuration or operating devices) are used for commissioning, configuring the DP system or system operation in normal operation (diagnostics) The DP programming interface provides the following services: Master diagnostics Slave diagnostics Read inputs/outputs of a slave Reading configuration data and Changing the slave address. The extended DP functions also include non-cyclic access to the parameters and measured values of a slave (e.g. field devices of the process automation, intelligent HMI devices). This type of slave has to be supplied with extensive parameter data during startup and normal operation. (DS_READ, DS_WRITE, DS_DATA_TRANSPORT).

3/350

Siemens IK PI 2001

Connection options for

PG/PC
CP 5614 communications processor
Functions (continued) Software for PG/OP communication This software enables programming of the SIMATIC S5/S7 controllers through PROFIBUS in connection with STEP 5/STEP 7. The PG/OP communication for the CP 5614 is already available after installing the CP 5614 (DP-Base). No additional software package is needed. S5-compatible communication (SEND/RECEIVE based on the FDL interface) SEND/RECEIVE (FDL interface) is already available after installation of the CP 5614 (DP-Base) and offers data exchange services for diagnostics and management. No additional software package is needed. Software for S7 communication (S7-5613) The user interface is compatible with S7-5412. SIMATIC S7 system components communicate with each other through S7 communication. The S7 programming interface enables PG/PC application programs access to SIMATIC S7 system components. The SIMATIC S7 data can be accessed easily and flexibly. The following services are available with S7 communication: Administrative services Link management Mini database Trace. Data transfer services Reading/writing of variables BSEND/BRECEIVE (up to 64 KB per task). Software for PROFIBUS-FMS interface (FMS-5613) The user interface is compatible with software FMS-5412. The FMS programming interface allows AT-compatible PCs to exchange data with FMS-capable controllers (e.g. S5/S7) and field devices of other manufacturers. The use of the FMS protocol ensures open communication. The following services are available through the FMS interface: Administrative services CRL management services FMS connection management services Object directory management services for clients and server. Variable services for clients and server (read, write, information report). Server functionality VFD (virtual field device) services for clients and server. Bus access information services (live list). Trace and mini database User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols PROFIBUSDP, S7 communication and PROFIBUS-FMS to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.). Programming interface through C-Library The programming interfaces for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0 For Borland programming interfaces (e.g. DELPHI) partner solutions of AIXO are available. For solutions for other operating systems, see the development kit DK-5613.
The DK-5613 can be found in the Internet at:

http://www.siemens.de/ simatic-net/dk5613

Siemens IK PI 2001

3/351

Connection options for

PG/PC
CP 5614 communications processor
Configuration

Configuration of S7 communication protocols, S5-compatible communication, DP protocol (DP/DPV1/ DPV2) and FMS protocol is executed in STEP 7/NCM PC, V5.1+SP2 or higher.

The configuring tool NCM PC is included in delivery of the PROFIBUS software package.

NCM PC is a component of Advanced PC Configuration.

Diagnosis

Extensive diagnostic tools are available (for installation, commissioning and operation) for the module itself and for the PROFIBUS network.

Therefore a PROFIBUS network can be started up quickly and easily with a CP 5614.

Designed for Industry

Only 1 slot is required for a master and slave Fastest possible access to process data through dual port RAM Short response time with FastLogic Process-consistent data from a DP cycle

Higher computing performance in the PC by relieving the host CPU Fast commissioning through Plug&Play and diagnostic tools Implementation for motion control applications through support of the equidistant mode

Easy portability to other operating systems through a dual port RAM interface Can also be used in high temperature industrial environments.

Programming device with CP 5613

SIMATIC S7-300 with CP 342-5 (DP master)

PROFIBUS
Transfer mechanism DP slave RS 485 DP master CP 5614 Distributed I/O

PROFIBUS

SIMATIC ET 200M

SIMATIC ET 200S

Fig. 3/114 Configuration example with CP 5614

3/352

Siemens IK PI 2001

G_IK10_deP0110s

Connection options for

PG/PC
CP 5614 communications processor
Technical specifications
Baud rates Interfaces, connection PROFIBUS-DP master PROFIBUS-DP slave Supply voltage (from PCI) Current consumption from 5 V DC Power loss Perm. ambient conditions Operating temperature Without fan With fan (air current 0.5 m/s) Transport/storage temperature Relative humidity Design Module format Dimensions (W H) in mm Weight Space required Performance data Single protocol mode No. of connectable DP slaves Data area of slave interface: input data, output data, diagnostics data No. of parallel FDL tasks to be processed No. of PG/OP and S7 connections No. of FMS connections approx. approx. 9.6 kbit/s to 12 Mbit/s 9-pin Sub-D socket 9-pin Sub-D socket 5 V DC, 5% 1.6 A 8.0 W

Ordering data

Order No. 6GK1 713-5DB60-3AA0

6GK1 713-5CB60-3AA0

max.

+5 C to +40 C +5 C to +60 C 40 C to +70 C 95% at +25 C PCI card 107 168 300 g 1 PCI slot

approx.

6GK1 713-5FB60-3AA0

max.

122

244 byte each

max. max. max.

120 50 1) 40 2)

1) For credit = 1; PDU size 480 byte 2) For credit = 1

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 500-0FC00

Ordering data
CP 5614 communications processor PCI card with master and slave connection to PROFIBUS, incl. Windows NT 4.0 WS, server, Windows 2000 Pro, server driver, DPRAM Interface for DP master and slave, PG and FDL, configuration software with electronic manual on CD-ROM

Order No.

6GK1 561-4AA00

} PROFIBUS 12M bus terminal Bus terminal for connecting PROFIBUS stations up to 12 Mbit/s with connecting cable
SIMATIC NET Software Update Service for Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, in German/English SIMATIC NET Manual Collection Electronic manuals for communication systems, protocols, products on CD-ROM German/English

6GK1 500-0AA10

6GK1 704-0AA00-3AA2

Development kit 1) DK-5613 Software development kit for CP 5613/CP 5614 for integration in any operating system environments on systems with PCI slot

6GK1 975-1AA00-3AA0

1) Download from the Internet at:

http://www.siemens.de/simatic-net/dk5613

Siemens IK PI 2001

3/353

Connection options for

PG/PC
CP 5614 FO communications processor
Overview
DP-M DP-S PG/OP S7 C

PCI card with microprocessor for system interfacing for PCs and SIMATIC PG/PC to the optical PROFIBUS with integrated interface up to 12 Mbit/s Integrated FOC interface for direct FO connection Communication services: PROFIBUS-DP master interface according to IEC 61 158/EN 50 170 on a PCI card PROFIBUS-DP slave interface according to IEC 61 158/EN 50 170 on a PCI card PG/OP communication with STEP 5 and STEP 7.

S5 C

FMS

OPC

S7 communication S5-compatible communication (SEND/RECEIVE) on the basis of the FDL interface PROFIBUS-FMS according to IEC 61 158/ EN 50170 High performance through direct dual port RAM access Event and filter mechanism for relieving the host CPU. Multiple protocol operation and parallel operation of up to 4 CPs OPC servers are supplied with the communication software a PROFIBUS card and can exchange data. The CP 5614 FO provides high performance support for control tasks on the PC (e.g. PC-based control, numeric control, robot control). It is connected to the optical PROFIBUS with integrated interface and OBT through: Plastic and PCF FOCs with simplex plugs. It is connected to the electrical PROFIBUS through Plastic and PCF fiber-optic cable with simplex plugs to an OBT.

3
Application The CP 5614 FO enables connection to PROFIBUS-DP for SIMATIC PG/PC and AT-compatible PCs with PCI slot under Windows NT 4.0 and Windows 2000. Design

It can be either a DP master or a DP slave independently of each other. In this way two different PROFIBUS networks can be connected in a hierarchical structure to one PC with

Short PCI card 2 duplex sockets for connection of plastic and PCF FOCs with 2 simplex plugs each to the optical PROFIBUS 9-pin Sub-D socket for connecting to PROFIBUS Connection for external power supply. This means data transmission on the optical line is not interrupted when the PC is switched off.

Diagnostic LEDs. Parallel operation of up to 4 CPs. The software can switch assignment of master and slave to the optical and electrical interface. The module is installed using standard PCI mechanisms (plug & play).

Functions

PROFIBUS-DP Access to process data The CP 5614 is operated as a PROFIBUS-DP master and slave module which holds the process image (input/output and diagnostic data) in the dual port RAM. The high-performance data exchange with the PROFIBUS slaves is handled independently by the CP 5614 FO hardware. The user has direct access to the dual port RAM. The process data of the slaves are always consistent, i.e. the user gets the data from one and the same DP cycle. Parallel operation of DP 5613 (DP master) and DP-Base (DP master, DP slave) is not possible.

Signaling by interrupt for diagnostic messages from slaves In equidistant mode signaling by interrupt: Start DP cycle End of cyclic data exchange with the DP slaves (from hardware version 3, available soon) Equidistant operation adjustable with STEP 7 V5.1 or higher or NCM PC V5. 1+SP2.

3/354

Siemens IK PI 2001

Connection options for

PG/PC
CP 5614 FO communications processor
Functions (continued) FastLogic (rapid shutdown) FastLogic means that the CP5614 FO can react automatically to up to 4 plant states. This achieves a fast response time and independence from the host application, e.g. for rapid equipment shutdown. DP programming interface The DP programming interfaces of the CP 5613 and CP 5614 FO are identical. The DP programming interface of the CP 5614 FO has the following functions: DP slave DP master class 1 including acyclic DP extensions. DP master class 2 (available soon) incl. non-cyclic expansions Access to the process data is directly through the dual port RAM. The dual port RAM interface not only offers fast access as a DP master/slave but also a basis for portability to other operating system environments (e.g. VXWorks, QNX, RMOS). A DP master and a DP slave library (DP_BASE.DLL or DPS_BASE.DLL) offer administrative function calls (initialization and management services as well as diagnostic functions). A transfer mechanism (application in the PC) can be set through software as a link for data exchange between the master and slave interface. In this manner, defined I/O data can be transferred between the master interface and the slave interface. The two connected PROFIBUS networks can be operated with different PROFIBUS bus parameters due to their mutual independence. Development kit DK-5613 The development kit DK-5613 offers access to the functions DP master class 1 including non-cyclic DP expansions With the software development kit DK-5613 the communications processors CP 5613 and CP 5614 can be integrated in any operating system environments. The kit contains the necessary source code including the descriptions in PDF format and can be downloaded from the Internet Access to process data with DP-5613 The user interface is compatible with software package DP-5412. DP master class 1 The CP 5614 FO operates as a DP master class 1 according to IEC 61158/EN 50170 and handles data transfer with the distributed stations (DP slaves) completely independently. In a fixed, repetitive message cycle, the central controller exchanges information with the DP slaves (e.g. ET 200S). The DP programming interface (DPLib.DLL) provides the PC programmer with function calls for data transfer. In addition, the DP interface offers the functions SYNC and FREEZE as well as the activation and deactivation of slaves. The DP functional expansions with respect to master class 1 enable non-cyclic read and write functions (DS_READ, DS_WRITE) as well as alarm acknowledgement (ALARM_ACK) to be performed parallel to cyclic data traffic. The non-cyclic transmitted data (e.g. parameterization data) are changed very rarely in comparison with the cyclic measured values and are transmitted with low priority parallel to the fast cyclic useful data transfer. Interrupt acknowledgment in the master ensures reliable transfer of the interrupts from DP slaves (DS_READ, DS_WRITE, DS_DATA_TRANSPORT). Parallel operation of DP-Base and DP 5613 software is not possible.

DP master class 2 In addition to DP master class 1 services, the CP 5614 FO also offers DP master class 2 services in connection with the DP programming interface according to IEC 61158/ EN 50170. Devices of this type (programming, configuration or operating devices) are used for commissioning, configuring the DP system or system operation in normal operation (diagnostics). The DP programming interface provides the following services: Master diagnostics Slave diagnostics Read inputs/outputs of a slave Reading configuration data and Changing the slave address. The extended DP functions also include non-cyclic access to the parameters and measured values of a slave (e.g. field devices of the process automation, intelligent HMI devices. This type of slave has to be supplied with extensive parameter data during startup and normal operation. (DS_READ, DS_WRITE, DS_DATA_TRANSPORT).

Siemens IK PI 2001

3/355

Connection options for

PG/PC
CP 5614 FO communications processor
Functions (continued) Software for PG/OP communication This software enables programming of the SIMATIC S5/S7 controllers through PROFIBUS in connection with STEP 5/STEP 7. The PG/OP communication for the CP 5614 FO is already available after installing the CP5614 FO (DP-Base). No additional software package is needed. S5-compatible communication (SEND/RECEIVE based on the FDL interface) SEND/RECEIVE (FDL interface) is already available after installation of the CP5614 FO (DP-Base) and offers data exchange services for diagnostics and management. No additional software package is needed. Software for S7 communication (S7-5613) The user interface is compatible with S7-5412. SIMATIC S7 system components communicate with each other through S7 communication. The S7 programming interface enables PG/PC application programs access to SIMATIC S7 system components. The SIMATIC S7 data can be accessed easily and flexibly. The following services are available with S7 communication: Administrative services Link management Mini database Trace Data transfer services Reading/writing of variables BSEND/BRECEIVE (up to 64 KB per task). Software for PROFIBUS-FMS interface (FMS-5613) The user interface is compatible with software FMS-5412. The FMS programming interface allows AT-compatible PCs to exchange data with FMS-capable controllers (e.g. S5/S7) and field devices of other manufacturers. The use of the FMS protocol ensures open communication. The following services are available through the FMS interface: Administrative services CRL management services FMS connection management services Object directory management services for clients and server. Variable services for clients and server (read, write, information report). Server functionality VFD (virtual field device) services for clients and server. Bus access information services (live list). Trace and mini database User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols PROFIBUSDP, S7 communication and PROFIBUS-FMS to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.). Programming interface through C-Library The programming interfaces for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0 For Borland programming interfaces (e. DELPHI) partner solutions of the AIXO Co. are available. For solutions for other operating systems, see the development kit DK-5613.

The DK-5613 can be found in the Internet at:

http://www.siemens.de/ simatic-net/dk5613

3/356

Siemens IK PI 2001

Connection options for

PG/PC
CP 5614 FO communications processor
Configuration

Configuration of S7 communication protocols, S5-compatible communication, DP protocol (DP/DPV1/ DPV2) and FMS protocol is executed in STEP 7/NCM PC, V5.1+SP2 or higher.

The configuring tool NCM PC is included in delivery of the PROFIBUS software package.

NCM PC is a component of Advanced PC Configuration.

Diagnosis

Extensive diagnostic tools are available (for installation, commissioning and operation) for the module itself and for the PROFIBUS network.

Therefore a PROFIBUS network can be started up quickly and easily with a CP 5614 .

Designed for Industry

Only 1 slot is required for a master and slave. Direct connection to the optical PROFIBUS through integrated FOC interface Fastest possible access to process data through dual port RAM Short response time with FastLogic Process-consistent data from a DP cycle

Higher computing performance in the PC by relieving the host CPU. Easy portability to other operating systems through a dual port RAM interface Implementation of motion control applications through support of the equidistant mode

Can also be used in high temperature industrial environments. Flexible application through switchable assignment of optical and electrical interface to master and slave

Programming device with CP 5613 FO

SIMATIC S7-300 with CP 342-5 FO

Optical PROFIBUS
Transfer mechanism DP Slave DP Master CP 5614 FO Distributed I/O FO RS 485 Switchable

PROFIBUS

SIMATIC ET 200M

SIMATIC ET 200S

Fig. 3/115 Configuration example with CP 5614 FO

Siemens IK PI 2001

3/357

G_IK10_deP0109s

Connection options for

PG/PC
CP 5614 FO communications processor
Technical specifications
Baud rates Basic interface setting PROFIBUS master PROFIBUS slave Interfaces switchable through software call PROFIBUS master PROFIBUS slave
External

Ordering data
9.6 kbit/s to 12 Mbit/s 2 duplex socket (FO) 9-pin Sub-D socket

Order No. 6GK1 713-5DB60-3AA0

9-pin Sub-D socket 2 duplex socket (FO) Low voltage socket 3.5 mm/1.3 mm + 5 V DC 5% 12 V DC 5% 1.6 A 0.3 A 8W 9 12 V DC 0.4 A 3.6 4.8 W

} DP-5613/Windows V6.0 Software for DP protocol incl. PG/OP communication, FDL, DP-OPC server; NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5613/ CP 5614/CP 5613 FO/CP 5614 FO; with electronic manual; on CD-ROM, in German/English } S7-5613/Windows V6.0 Software for S7 communication incl. PG/OP communication, FDL, S7-OPC server; NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5613/ CP 5614/CP 5613 FO/CP 5614 FO; with electronic manual; on CD-ROM, in German/English } FMS-5613/Windows V6.0 Software for FMS protocol incl. PG/OP communication, FDL, FMS-OPC server; NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5613/ CP 5614/CP 5613 FO/CP 5614 FO; with electronic manual; on CD-ROM, in German/English
PROFIBUS FastConnect RS 485 bus connector Plug 180 PROFIBUS 12M bus terminal

power supply (optional) through standard external power supply

6GK1 713-5CB60-3AA0

Supply voltage (from PCI) Current consumption from 5 V DC from 12 V DC Power loss Supply voltage (optional) external power supply Current consumption Power loss Perm. ambient conditions Operating temperature Without fan With fan (air current 0.5 m/s) Transport/storage temperature Relative humidity Design Module format Dimensions (W H) in mm Weight Space required Performance data Single protocol mode No. of connectable DP slaves Data area of slave interface: input data, output data, diagnostics data No. of parallel FDL tasks to be processed No. of PG/OP and S7 connections No. of FMS connections

6GK1 713-5FB60-3AA0

max.

+5 C to +40 C +5 C to +60 C 40 C to +70 C 95% at +25 C PCI card 107 168 300 g 1 PCI slot

} }

6GK1 500-0FC00

6GK1 500-0AA10 6GK1 901-0FB00-0AA0 6GK1 905-6PA10 6ES7 195-1BE00-0XA0

approx.

PROFIBUS plastic fiber-optic, simplex plug / polishing set PROFIBUS plastic fiber-optic, stripping tool set Connection adapters 50 pcs.

max.

122

244 byte each

max. max. max.

120 50 1) 402)

Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Paper version Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server including manuals, on CD-ROM, German/English SIMATIC NET Manual Collection Electronic manuals for communication systems, protocols, products on CD-ROM German/English 1) Download from the Internet at:

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 704-0AA00-3AA2

1) For credit = 1; PDU size 480 byte 2) For credit = 1

Ordering data
CP 5614 FO communications processor PCI card with master and slave connection to PROFIBUS, incl. Windows NT 4.0 WS, server, Windows 2000 Pro, server driver, DPRAM Interface for DP master and slave, configuration software with electronic manual on CD-ROM Development kit 1) DK-5613 Software development kit for CP 5613/CP 5614 for integration in any operating system environments on systems with PCI slot

Order No.

6GK1 561-4FA00

6GK1 975-1AA00-3AA0

http://www.siemens.de/simatic-net/dk5613

3/358

Siemens IK PI 2001

Connection options for

PG/PC
CP 5511 communications processor
Overview
DP-M DP-S PG/OP S7 C

PCMCIA card type II; for PG/PCs with PCMCIA slot and notebooks Used with: STEP 7, ProTool, NCM PC, Micro/Win, ProTool/Pro, SIMATIC PDM (for PG/OP communication) COM PROFIBUS SOFTNET S7 (for S7 communication). SOFTNET DP (for DP). OPC servers are supplied with the communication software

S5 C

FMS

OPC

Application

For connecting PCMCIA slot and notebooks

Design

PCMCIA card type II Adapter with 9-pin Sub-D socket for connection to PROFIBUS The following software packages support the CP 5511: STEP 7 as of V3.2 Drivers for the CP 5511 are supplied with STEP 7 SOFTNET-S7 The S7 programming interface can be used with this package SOFTNET-DP With this the CP 5511 can be used as a PROFIBUS-DP master class 1 or 2 SOFTNET-DP slave for using the CP 5511 as a PROFIBUS-DP slave

Functions

The CP 5511 is operated under different software packages and allows the user to execute programming device functions and PC functions through PROFIBUS and the multipoint interface (MPI). Only one CP can be operated for each PG/PC/notebook. Similarly only one protocol (PROFIBUS-DP, S7 communication or FDL) can be used for each CP.

Siemens IK PI 2001

3/359

Connection options for

PG/PC
CP 5511 communications processor
Designed for Industry

Connection for notebooks or other portable PCs to PROFIBUS (e.g. for diagnostics and commissioning)

Easy installation and commissioning

Technical specifications
Data transfer rate Interfaces Connection to PROFIBUS Connection to PG/PC Supply voltage Current consumption Power loss Perm. ambient conditions Operating temperature Transport/storage temperature Relative humidity 9.6 kbit/s to 12 Mbit/s 9-pin Sub-D socket PCMCIA slot type II +5 V DC 5% typ. 270 mA, max. 360 mA 1.8 W +5 C to +40 C 20 C to +60 C 95% at +25 C PCMCIA type II 54 85 5 30 g 130 g 1 PCMCIA slot type II

Ordering data
CP 5511 communications processor PCMCIA card for connecting a PG or PC to PROFIBUS or MPI SOFTNET-S7/Windows V6.0 Software for S7 communication incl. FDL, S7-OPC server, NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5511 and CP 5611, with electronic manual on CD-ROM SOFTNET-DP/Windows V6.0 Software for DP protocol (master class 1 and 2), FDL incl. DP-OPC server, NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5511 and CP 5611, with electronic manual on CD-ROM SOFTNET-DP Slave/Windows V6.0 Software for DP slave, incl. OPC server, under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5511 and CP 5611, with electronic manual on CD-ROM PROFIBUS FastConnect RS 485 bus connector Plug 180 With 180 cable outlet Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Paper version Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English SIMATIC NET Manual Collection Electronic manuals for communication systems, protocols, products on CD-ROM German/English

Order No.

6GK1 551-1AA00

6GK1 704-5CW60-3AA0

max.

6GK1 704-5DW60-3AA0

Design Module format Dimensions (W H D) in mm Weight without adapter approx. with adapter approx. Space required

6GK1 704-5SW60-3AA0

6GK1 500-0FC00

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

3/360

Siemens IK PI 2001

Connection options for

PG/PC
CP 5611 communications processor
Overview
DP-M DP-S PG/OP S7 C

Short PCI card for programming device / PC with PCI slot. Used with: STEP 7, STEP 7-Micro/Win, SIMATIC NCM PC, ProTool, ProTool/Pro, SIMATIC PDM (for PG/OP communication) COM PROFIBUS SOFTNET-S7 (for S7 communication). SOFTNET DP (for DP). OPC servers are supplied with the communication software

S5 C

FMS

OPC

Application

For PGs/PCs with PCI slot.

Design

Short PCI card 9-pin Sub-D socket for connection to PROFIBUS The following software packages support the CP 5611: STEP 7 V3.2 upwards under Windows 95 and NT 4.0; Windows 98 from V4.02 and K4.02.5. Drivers for the CP 5611 are included in delivery of STEP 7. SOFTNET-S7 The S7 programming interface can be used with this package SOFTNET-DP With this the CP 5611 can be used as a PROFIBUS-DP master class 1 or 2 SOFTNET-DP Slave For using the CP 5611 as a PROFIBUS-DP slave

Functions

The CP 5611 is operated under different software packages and allows the user to execute programming device functions and PC functions through PROFIBUS and the multipoint interface (MPI). Only one CP can be operated for each programming device/PC. Similarly only one protocol (PROFIBUS-DP, S7 communication or FDL) can be used for each CP.

Siemens IK PI 2001

3/361

Connection options for

PG/PC
CP 5611 communications processor
Designed for Industry

Connection for portable PCs to PROFIBUS (e.g. for diagnostics and commissioning)

Easy installation and commissioning

Technical specifications
Data transfer rate Interfaces Connection to PROFIBUS 9.6 kbit/s to 12 Mbit/s 9-pin Sub-D socket +5 V DC 5% 0.5 A 2.0 W +5 C to +40 C 20 C to +60 C 95% at +25 C PCI card 102 130 100 g 1 PCI slot

Ordering data
CP 5611 communications processor PCI card for connecting a PG or PC to PROFIBUS CP 5611 MPI Consists of PCI card CP 5611 and MPI cable, 5 m SOFTNET-S7/Windows V6.0 Software for S7 communication incl. FDL, S7-OPC server, NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5511 and CP 5611, with electronic manual on CD-ROM SOFTNET-DP/Windows V6.0 Software for DP protocol (master class 1 and 2), FDL incl. DP-OPC server, NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5511 and CP 5611, with electronic manual on CD-ROM SOFTNET-DP Slave/Windows V6.0 Software for DP slave, incl. OPC server, under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5511 and CP 5611, with electronic manual on CD-ROM PROFIBUS FastConnect RS 485 bus connector Plug 180 With 180 cable outlet

Order No.

6GK1 561-1AA00

} }

6GK1 561-1AM00

6GK1 704-5CW60-3AA0

max.

6GK1 704-5DW60-3AA0

approx.

6GK1 704-5SW60-3AA0

6GK1 500-0FC00

} PROFIBUS 12M bus terminal Bus terminal for connecting PROFIBUS stations up to 12 Mbit/s with connecting cable
Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Paper version Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English SIMATIC NET Manual Collection Electronic manuals for communication systems, protocols, products on CD-ROM German/English

6GK1 500-0AA10

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

3/362

Siemens IK PI 2001

Connection options for

PG/PC
SOFTNET for PROFIBUS
Overview
DP-M DP-S PG/OP S7 C

CP 5611

CP 5511

PG/PC

SOFTNET for PROFIBUS

S5 C

FMS

OPC

PROFIBUS

S5-115U to S5-155U with CP 5431 FMS/DP

S7-300 with CP 342-5 or CP 343-5

S7-400 with CP 443-5

G_IK10_deP0039s

Software for linking programmable controllers/PCs and notebooks to automation systems.

Fig. 3/116 System configuration: SOFTNET for PROFIBUS

OPC servers are supplied with the communication software

Application

SOFTNET for PROFIBUS can be used to connect PCs to automation systems, e.g. SIMATIC S7, through PROFIBUS. The following are available as user interfaces:

DP protocol PG/OP communication for SIMATIC S7 S7 communication S5-compatible communication (SEND/RECEIVE based on the FDL interface)

Principle of operation

SOFTNET processes the complete protocol stack in the PC.

This architecture means that, unlike CP 5613 or CP 5614 products the performance capability of the SOFTNET Devices of this type (programming devices, configuration devices or operating devices) are used on startup, on configuring the DP system or for operating the system during normal operation (e.g. diagnostics). The DP programming interface provides the following services: Master diagnostics, slave diagnostics, reading the inputs and outputs of a slave, reading configuration data and changing the slave address. The extended DP functions also include non-cyclic access to the parameters and measured values of a slave (e.g. field devices of the process automation, intelligent HMI devices. This type of slave must be supplied with extensive parameter data during startup and normal operation (DS_READ, DS_WRITE, DS_DATA_TRANSPORT).

Functions

DP slave (SOFTNET-DP slave) A DP slave is an I/O device that reads input information and supplies output information to the I/O. The quantity of input and output information depends on the type of device and can be up to 244 byte. The slave applications can be implemented on the PC using the functions SET_INPUT and SET_OUTPUT of the slave programming interface. Configuration of PROFIBUS-DP takes place with the enclosed COM PROFIBUS PC-Edition. For the slave interface, an example GSD file is provided which can be adapted to the relevant application.

Siemens IK PI 2001

3/363

Connection options for

PG/PC
SOFTNET for PROFIBUS
Functions (continued) Software for PG/OP communication No special programming packages are required for the CP 5511 and CP 5611 because the drivers are included in delivery of STEP 7. The SOFTNET-PG S5 software is available for programming the SIMATIC S5 with STEP 5 (V7.2 or higher). Software for S7 communication (SOFTNET-S7) SIMATIC S7 system components communicate with each other through S7 communication. The S7 programming interface enables PG/PC application programs access to SIMATIC S7 system components. The SIMATIC S7 data can be accessed easily and flexibly. The following services are available with S7 communication: Administrative services Link management Mini database Trace. Data transfer services Reading/writing of variables BSEND/BRECEIVE (up to 64 KB per task). The complete configuration of the S7 communication is performed using STEP 7 V5.0 SP3 and higher. The configurations generated for the PCs using STEP 7 are stored in files which are subsequently transferred to the individual PCs. Software for S5-compatible communication (SEND/ RECEIVE based on the FDL interface) This layer 2 based interface is used for communication between PG/PC and SIMATIC S5 PG/PC and SIMATIC S7 PG/PC and PG/PC SEND/RECEIVE offers the following services: Management services Connection establishment services Data transfer services This interface is contained in SOFTNET-DP and SOFTNETS7. Configuration is not necessary. User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols PROFIBUSDP, S7 communication and PROFIBUS-FMS to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.). Programming interface through C-Library The programming interfaces for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ Version 6.0 Microsoft Visual Basic Version 6.0 For Borland programming interfaces (e.g. DELPHI) partner solutions of AIXO are available.

3/364

Siemens IK PI 2001

Connection options for

PG/PC
SOFTNET for PROFIBUS
Configuration

Configuration of S7 communication protocols, S5-compatible communication, DP protocol (DP/DPV1/ DPV2) and FMS protocol is executed in STEP 7/NCM PC, V5.1+SP2 or higher. Low-cost integration as PROFIBUS-DP master class 1 or master class 2 with SOFTNET-DP. As a PROFIBUS-DP slave with SOFTNET-DP slave

The configuring tool NCM PC is included in delivery of the PROFIBUS software package.

NCM PC is a component of Advanced PC Configuration.

Designed for Industry

S7 communication with SOFTNET-S7

Performance data: Single protocol operation

CP 5511 No. of connectable DP slaves No. of parallel FDL tasks to be processed No. of PG/OP and S7 connections max. max. max. 60 32 8 CP 5611 60 100 8

Ordering data
DP interface SOFTNET-DP/Windows V6.0 Software for DP protocol (master class 1 and 2), FDL incl. DP-OPC server, NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5511 and CP 5611, with electronic manual on CD-ROM S7 communication SOFTNET-S7/Windows V6.0 Software for S7 communication incl. FDL, S7-OPC server, NCM PC under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5511 and CP 5611, with electronic manual on CD-ROM SOFTNET-DP Slave/Windows V6.0 Software for DP slave, incl. OPC server, under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 5511 and CP 5611, with electronic manual on CD-ROM Manual CP 5613/CP 5614 and SOFTNET for PROFIBUS Paper version Including: Description of the interfaces (FMS, DP, S7, FDL), OPC server, configuration tools German English SIMATIC NET Software Update Service For Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English SIMATIC NET Manual Collection Electronic manuals for communication systems, protocols, products on CD-ROM German/English

Order No.

6GK1 704-5DW60-3AA0

6GK1 704-5CW60-3AA0

6GK1 704-5SW60-3AA0

} } }

6GK1 971-5DA00-0AA0 6GK1 971-5DA00-0AA1 6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

Siemens IK PI 2001

3/365

Industrial Ethernet
System interfacing for PG/PC
Overview
System interfacing for PG/PC

CPs with their own microprocessor

Protocol software runs on the CP Free PC resources for applications Suitable for extensive applications Recommended for applications with HMI systems with high performance requirements, such as WinCC Recommended for largescale systems (> 5 stations, e.g. SIMATIC) Constantly high communication throughput Use for redundant commuinication Time synchronization

CP 1613 (PCI)

You can find software for the PC products under Windows on the SIMATIC NET/Windows CD including the relevant manuals in pdf format and comprehensive further information on SIMATIC NET products and communication. The necessary configuring tools are supplied with all software packages.

CP 1612 (PCI)

CPs without their own microprocessor

Protocol software runs on the PG/PC PC resources are divided between communication and applications Suitable for less extensive applications Recommended for smaller systems (up to 4 stations, e.g. SIMATIC) Communication performance depends on PC resources and workload

CP 1512 (PCMCIA)

Fig. 4/55 System interfacing for PG/PC

Siemens IK PI 2001

4/123

Industrial Ethernet
System interfacing for PG/PC
Overview
Data throughput Industrial Ethernet A comparison between CP 1512, CP 1612 and CP 1413 (predecessor of CP 1613) and CP 1613 shows the course of the respective communication performance. With the appropriate software packages, this course fluctuates in CP 1512 and CP 1612 between 0 and the maximum throughput. Used with software packages, communication performance for the CP 1613 is stable and high, permitting fast response times without fluctuations.

Time
1)

CP 1613 Constantly high communication performance

Messages/s

CP 1413 Constant communication performance CP 1512/CP1612 Fluctuating communication performance

1) The CP 1613 is the successor module to the CP 1413

Fig. 4/56 Comparison of communication performance characteristics

CPU load

The communication must share the PC resources with other applications (especially HMI). In general, therefore, less than 25% of the host CPU time remains available for communication.

While under these conditions devices such as CPs 1512/1612 only lets through an average of approx. 80 messages (with strongly fluctuating curve), CP 1613 still offers maximum throughput.

The throughput specifications are mean values and depend on the individual system configuration of the PC.

Throughput (frames/s) PC processor performance for communication

100% 75% 50% 25%

Messages/s

CPU load

CP 1413

CP 1512 CP 1612

CP 1613

Fig. 4/57 CP 1613 throughput at 20% CPU availability for communication

4/124

Siemens IK PI 2001

G_IK10_deI0038s

G_IK10_deI0037s

Industrial Ethernet
Introduction
System interfacing for PG/PC; OPC server
Overview OPC servers are included in delivery of the communication software Standard, open, manufacturer-independent interface Interfacing of OPC-capable Windows applications to S7 communication and S5compatible communication (SEND/RECEIVE). Builds upon software programming interfaces. Efficient data exchange for Windows NT 4.0 and Windows 2000 OPC scout as OPC client with browser functionality and OCX data control

PC/Windows NT and Windows 2000 SIMATIC NET OPC-Manager WinCC OPC-Client Microsoft Office OPC-Client

FMS-OPC server

DP-OPC server

S7-OPC server

FMS protocol

DP protocol

S7 comm.

S5-comp. comm. (SEND/RECEIVE)

S7-400 FMS-PC SIMATIC S5 (SEND/RECEIVE only)

S7-300

0 1

ET 200X

SIMATIC S5

PROFIBUS

Ind. Ethernet

S7-PC
G_IK10_deI0067s

Fig. 4/58 System integration with OPC server

Application

Under Windows NT and Windows 2000, OPC (OLE for Process Control) can be used as an extension to the communications interfaces COM (Component Object Model) and DCOM (Distributed COM) for the user software. The basic principle of OPC is that OPC client applications can communicate with the OPC server through a standard / open and thus multivendor interface. Can be integrated in OPCcapable Windows applications (Microsoft Office or HMI system) already commercially available.

For Industrial Ethernet, the following OPC servers are available: S7 OPC servers for S7 communication, alarms and events as well as S5-compatible communication (SEND/RECEIVE) The OPC servers have: Standardized access to SIMATIC S7 and SIMATIC S5 for OPC-capable applications under Windows NT and Windows 2000 Consistency between automation products from different manufacturers

Consistent and easy-to-use user interface for different components. Accessibility from every computer in the LAN High-performance data access through the Custom Interface (C++) Easy to use through the Automation Interface (VB) or OCX data control, which is supplied

Functions

Open standardization of addressing using logical names for objects of an automation component or system. Support of symbols from STEP 7 Efficient data exchange from a process component to a further processing application

Simultaneous use of several servers by one client application Several clients can run on one OPC server at the same time Server-specific configuration support Interfaces Custom Interface for high-performance C++ applications

Automation Interface for easy-to-create Visual Basic or similar applications OCX data control for direct integration in Windows applications that support COM/DCOM

Siemens IK PI 2001

4/125

Industrial Ethernet
Introduction
System interfacing for PG/PC; OPC server

Application X

Application Y

WinCC OPC Client

Application X OPC Client

Server A

Server B

Server C

Fig. 4/59 Comparison of conventional client/server architecture with an OPC architecture

Configuration

4
Designed for Industry

The complete configuration of the communications parameters is executed with the tools of the installed Software Advanced PC Configuration (Configuration Console, SIMATIC NCM PC).

The following demo programs are included in delivery: For custom interface in C++ For Automation Interface with Visual Basic

Other compilers can be implemented through the OPC server, however, the compiler must support the COM interface (Microsoft Component Object Model)

Simple use of different networks and protocols through standard interface. Reduced training and learning requirements.

Easy integration in the system environment and office applications through C++ and Visual Basic interface Short programming times for applications.

Easy to handle and costeffective as delivery of the communication software includes the OPC server

Technical specifications OPC server

Programming

Product versions
Product S7-1613 TF-1613 SOFTNET-S7 Industrial Ethernet contains OPC servers for: S7 communication S5-compatible communication S5-compatible communication S7 communication S5-compatible communication

Synchronous and asynchronous reading and writing of variables Monitoring of variables through the OPC server with alarm to the client in the event of change Use of quantity operations; this enables a large volume of data to be process in a short time Custom Interface (C++); OPC is therefore powerful Automation Interface (VB, Excel, Access, Delphi, etc.); therefore easy to use Graphics with OCX; allowing configuration instead of programming DP protocol S7 communication FMS protocol S5-compatible communication (SEND/RECEIVE) Windows NT 4.0 Workstation and server Windows 2000 Workstation and server

Interfaces

Protocols

Operating systems

4/126

Siemens IK PI 2001

G_IK10_deP0041s

FMS-OPC Server

S7-OPC Server

XY-OPC Server

DP-OPC Server

Industrial Ethernet
System interfacing for PG/PC
Advanced PC Configuration
Overview Advanced PC Configuration is included in delivery of the communications software from version 6.0 onwards. Simple handling thanks to automatic software installation, Plug & Play and user-prompted commissioning Simple, consistent and costeffective configuration and planning and design of a PC station Considerably simplified OPC configuration Advanced PC Configuration is delivered with the new configuring tool NCM PC and the tools Startup Wizard and Configuration Console.

Application

Advanced PC Configuration stands for a new, simple, consistent and cost-effective startup and diagnostics of a PC station. The Startup Wizard, Configuration Console and NCM PC mark the launch of a whole new world of tools.

The Startup Wizard guides the user through all the steps necessary to achieve a ready-to-run PC station The Configuration Console is the central tool for configuration settings and diagnostics

NCM PC V5.1+SP2 offers a new configuring tool for STEP 7-compatible PC configuration

Functions

Settings on the OPC servers delivered with the communications software are also executed through the Configuration Console.

Siemens IK PI 2001

4/127

Industrial Ethernet
System interfacing for PG/PC
Advanced PC Configuration
Functions (continued) NCM PC NCM PC replaces the previous PC configuration tools COML S7 and COM PROFIBUS PC Edition. In future, PC configuration can be carried out in either STEP 7 or NCM PC, version V5.1+SP2 or higher. Both tools offer the same look & feel and create the same database. This ensures consistent configuration of protocols for S5-compatible communication, S7 communication, DP protocols and FMS protocols. No further need for multiple entries and data consistency is automatically ensured. A configuration wizard integrated in NCM PC also ensures user-prompted configuration of the PC station. With NCM PC and STEP 7, from Version V5.1+SP2, a PC can be configured in the same way as a SIMATIC S7 station and loaded through the network. This applies both to the local station on which NCM PC or STEP 7 is installed and the remote station that is operated through the network.
Note: NCM PC does not contain a conversion for LDBs that were created with COM PROFBUS or COML S7. In this case these must be re-configured. For further information on Advanced PC Configuration and the previous versions of PC/Windows software products please visit us in the Internet at:

http://www.siemens.de/ simatic-net/ik-info_en

Advanced PC Configuration

Engineering station PG/PC with STEP 7 or NCM PC

PROFIBUS Industrial Ethernet

S7-400 Runtime PC with application software Runtime PC with application software

Fig. 4/60 PC configuration with STEP 7 or NCM PC

4/128

Siemens IK PI 2001

Industrial Ethernet
System interfacing for PG/PC
Advanced PC Configuration
Designed for Industry Simple use of different networks and protocols through standard configuration. Reduced training and learning requirements. Short setting times for communication Uniform procedure and configuration functionality, as for STEP 7

Technical specifications Advanced PC Configuration

Supported modules

Ordering data
Advanced PC Configuration

Order No. The following products are included in the scope of supply: S7-1613 PG-1613 SOFTNET-PG for Industrial Ethernet SOFTNET-S7 for Industrial Ethernet SIMATIC NET CD 07/2001 Upgrade

CP 1512, CP 1612, CP 1613 CP 1612 compatible PROFIBUS interfaces of PCs/PGs S5-compatible communication S7 communication Windows NT 4.0 SP 6a Windows 2000 +SP1 for Professional and servers

Protocols Operating systems

Siemens IK PI 2001

4/129

Industrial Ethernet
PG/PC
CP 1613 communications processor
Overview
ISO TCP/IP PG/OP S7 C

PCI card with microprocessor for connecting PG/PC to Industrial Ethernet with 10/100 Mbit/s autosensing Communication services through ISO or TCP/IP transport protocols PG/OP communication S7 communication S5-compatible communication (SEND/RECEIVE) TF protocol

Delivery of the communication software includes the OPC servers. 15-pin AUI/ITP RJ45 connection ISO and TCP/IP transport protocol onboard Large quantity framework

S5 C

OPC

Design

The CP 1613 module (card with microprocessor) is plugged directly into a SIMATIC PG/PC or a PC and requires a short PCI slot.

4
Mode of operation The module independently processes the protocols up to and including level 4 (transport). To permit a large quantity framework and high communication integrity, 16 MB of memory are provided. User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols S7 communication and S5-compatible communication to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.).

Connections: 15-pin Sub-D socket for use in industrial applications (automatic switching between AUI, ITP and RJ45 interface) RJ45 for connection in the office environment

In the case of electrical networks, forexample the module is connected to the 727-0 bus through a 727-1 connecting cable/ transceiver. for ITP through the ITP standard cable 9/15 to OSM/ESM/star coupler for optical networks through the Mini OTDE optical transceiver. The data transfer between the host system and the CP 1613 is handled by a Windows NT driver or Windows 2000 driver. The transfer rate is detected and automatically switched over (autosensing).

The data exchange between module and host takes place in master mode. This means that the CP 1613 accesses the physical RAM of the host.

Functions

Programming interface through C library The programming interfaces for the protocols S7 communication, PG/OP communication, S5-compatible communication and TF protocol for existing applications are implemented as a Dynamic Link Library (DLL). The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0 Other compilers can be implemented through the OPC server, however, the compiler must support the COM interface (Microsoft Component Object Model)

Software for PG/OP communication This software permits programming of SIMATIC S5 and S7 PLCs through Industrial Ethernet in combination with STEP 5/STEP 7 automation systems. It is contained in all CP 1613 software packages.

4/130

Siemens IK PI 2001

Industrial Ethernet
System interfacing for PG/PC
CP 1613 communications processor
Application The CP 1613 enables connection to Industrial Ethernet (10/100 Mbit/s) for SIMATIC PG/Industrial PC and PCs with PCI slot.

10 Mbit/s

Triaxial network
Transceiver

727-0 bus cable (triaxial cable) up to 500 m

727-1 connecting cable up to 50 m

10/100 Mbit/s

Twisted pair network (Sub-D)

OSM / ESM / OLM / ELM

ITP standard cable up to 100 m

CP 1613

4
10/100 Mbit/s
Structured cabling according EN 50173 Twisted pair switch (e.g. ESM TP80)

Twisted pair network (RJ45)

AUI ITP RJ45

FC Outlet RJ45

FC standard cable RJ45/RJ45 TP Cord RJ45/RJ45 TP Cord

RJ45

100 Mbit/s
OSM BC08

Fiber optic network

OMC FOC

Fig. 4/61 Mains connection options CP 1613

Siemens IK PI 2001

4/131

G_IK10_deI0051s

RJ45/RJ45 TP Cord

Industrial Ethernet
System interfacing for PG/PC
CP 1613 communications processor
Functions (continued) Software for S7 communication (S7-1613 or S7-REDCONNECT) The S7 programming interface enables PG/PC applications (e.g. WinCC) and application programs access to SIMATIC S7/ system components. Thus, easy and flexible access to the data of the SIMATIC S7/M7 is possible. S7 communication provides: Administrative services Link management Mini database Trace Data transfer services Reading/writing of variables BSEND/BRECEIVE With S7-REDCONNECT, communication with the highavailability S7-400H system is possible.

Software for S5-compatible communication (SEND/RECEIVE) This layer 4 based interface is used for communication between PG/PC and SIMATIC S5 PG/PC and SIMATIC S7 PG/PC and PG/PC S5-compatible communication (SEND/RECEIVE) provides the following services: Management services Connection establishment services Data transfer services The software is contained in the products S7-1613 and TF-1613.

Software for TF protocol (TF-1613) The technological functions interface offers access to the MAP 3.0 open and wellproven automation protocol on Ethernet. The Technological Functions correspond in functionality to the international MMS services in accordance with ISO IS 9506. MMS/TF services: Variable services Domain services Program invocation services General services for virtual devices (VMD support service) Services of TF link management (environment and general management services).

Configuration

Configuration of S7 communication protocols and S5compatible communication is executed in STEP 7/ NCM PC, V5.1 SP2 or higher. The TF configuration is executed using COML TF.

The configuring tools NCM PC and COML TF are included in delivery with the CP 1613 software packages. NCM PC is a component of Advanced PC Configuration.

For further information on Advanced PC Configuration and the previous versions of PC/Windows software products please visit us in the Internet at:

http://www.siemens.de/ simatic-net/ik-info_en

Designed for Industry

Continuous data throughput through protocol processing on the CP. Can be connected to any Ethernet network through AUI/ITP or RJ45 ports on the module.

Free computer capacity for further applications in the PC, e.g. HMI (ISO and TCP/IP transport onboard) Simple handling through plug & play and autosensing (10/100 Mbit/s).

Operation of large network configurations with one card due to large number of connections Can be used for redundant communication. OPC as common interface

4/132

Siemens IK PI 2001

Industrial Ethernet
System interfacing for PG/PC
CP 1613 communications processor
Technical specifications
Data transfer rate Interfaces Connection to Industrial Ethernet (10/100 Mbit/s)
10BaseT,

Ordering data
10/100 Mbit/s 15-pin Sub-D socket (autom. switching between AUI and twisted pair) RJ45 5 V DC 5% 12 V DC 5% 600 mA 500 mA 4W +5 C to +40 C 20 C to +60 C 95% at +25 C Short AT format 107 x 167 200 g 1 x PCI slot CP 1613 PCI card for connection to Industrial Ethernet (10/100 Mbit/s) with AUI/ITP and RJ45 port

Order No.

6GK1 161-3AA00

100BaseTX

Supply voltage Current consumption From 5 V DC From 12 V DC Power loss Perm. ambient conditions Operating temperature Transport/storage temperature Relative humidity Design Module format Dimensions (W x D) in mm Weight Space required Performance data Single protocol mode S7 and PG/OP communication No. of usable connections ISO TCP/IP S5-compatible communication (SEND/RECEIVE) No. of usable connections ISO TCP/IP

} S7-1613/Windows V6.0 Software for S7-Communication S5-compatible communication (SEND/RECEIVE) incl. OPC, PG/OP-Communication, NCM PC, up to 120 connections, under Windows NT 4.0 WS, server; Windows 2000 Pro, server for CP 1613 with electronic manual on CD-ROM German/English } TF-1613/Windows V6.0 Software for TF protocol, S5-compatible communication, incl. OPC, PG/OP communication under Windows NT 4.0 WS, server; Windows 2000 Pro, server for CP 1613 with electronic manual on CD-ROM German/English } PG-1613/Windows V6.0 Software for PG/OP communication, NCM PC, under Windows NT 4.0 WS, server; Windows 2000 Pro, server for CP 1613, with electronic manual on CD-ROM German/English
S7-REDCONNECT/Windows V1.4 } Software for fail-safe S7 communication through redundant networks, incl. S7-OPC server under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 1613, with electronic manual on CD-ROM German/English Upgrade S7-REDCONNECT/ Windows V1.4 For expansion of S7-1613/Windows on S7-REDCONNECT/Windows V1.4, under Windows NT 4.0 WS, server; Windows 2000 Pro, server; with electronic manual on CD-ROM German/English CP 1613 and SOFTNET for Industrial Ethernet manual Hardcopy version: contains description of the interfaces (S7, TF, S5-compatible communication), OPC server, configuring tool for CP 1613 German English SIMATIC NET Manual Collection Electronic manuals for communication systems, protocols, products on CD-ROM German/English SIMATIC NET Software Update Service for Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English

6GK1 716-1CB60-3AA0

6GK1 716-1TB60-3AA0

max.

approx.

6GK1 716-1PB60-3AA0

max. max.

120 120

4
6GK1 716-0HB14-3AA0 6GK1 716-0HB14-3AA4

max. max.

120 120

} } }

6GK1 971-1GA00-0AA0 6GK1 971-1GA00-0AA1 6GK1 975-1AA00-3AA0

6GK1 704-0AA00-3AA2

Siemens IK PI 2001

4/133

Industrial Ethernet
System interfacing for PG/PC
S7-REDCONNECT
Overview
ISO TCP/IP PG/OP S7 C
PC with S7-REDCONNECT and 2 x CP 1613

G_IK10_deI0048s

For connection of PCs for redundant Industrial Ethernet to SIMATIC S7-400H For redundantly structured Industrial Ethernet. Operation is also possible in non-redundant networks.

S5 C

OPC
Industrial Ethernet Industrial Ethernet

Completely integrated in STEP 7 from V5.0. Delivery of the communication software includes the OPC servers

S7-400H

Fig. 4/62 System configuration S7-REDCONNECT

Application

The software package S7-REDCONNECT connects the SIMATIC S7-400H to applications on the PC, e.g. WinCC.

Typically, a redundant Industrial Ethernet is used. The software package can also be used where SIMATIC H systems are operated on nonredundant networks. PC with: up to four CP 1613 and S7-REDCONNECT for connecting the PC to Industrial Ethernet with ISO-Protocol under Windows NT4.0, 2000 Pro Fault detection, switching over if required, communication monitoring and synchronization are handled in the background invisible to the application.

Mixed operation of redundant and non-redundant systems is also possible.

Design

The following components are necessary for assembling a SIMATIC H system with PC connection

S7-400H with: CP 443-1 for connecting the S7-400H to Industrial Ethernet with ISO protocol STEP 7 from V5.0 upwards for configuring.

Mode of operation

The highly available S7 communication is fed through a master and a reserve connection concealed for the application which is monitored during operation and switched over in the event of a fault.

The application, e.g. WinCC, communicates with the 2 subunits of the S7-400H in the same way as with an S7 CPU.

Functions

S7-REDCONNECT contains the functional scope of the S7-1613 software package (S7 communication, S5-compatible communication and PG/OP communication) as well as additional redundant communication through S7 connections. An additional licence for S7-1613 is not required. S5-compatible communication Time-of-day synchronization Continued use of existing Windows applications Services for monitoring the redundant communication. Diagnostics tool for visualizing the communication status

Simple redundancy through 2-way communication (STEP 7 V5.0 SP2 or higher) Increased redundancy through 4-way communication (STEP 7 V5.1 or higher)

4/134

Siemens IK PI 2001

Industrial Ethernet
System interfacing for PG/PC
S7-REDCONNECT
Configuration
PC with S7-REDCONNECT and 2 x CP 1613 PC

OSM OSM

S7-300
OSM OSM

10/100 Mbit/s

Third-party system

100 Mbit/s

OSM OSM

S7-400
OSM OSM OSM OSM

H system

S7-400

H system
G_IK10_deI0053s

Fig. 4/63 Redundant network with S7-400 H and OSM

Configuration

The configuration established for the PCs with STEP 7 from V5.0 is written to files and transferred to the PCs.

Designed for Industry

Provides protection against communication failure in the event of a fault in the double bus or in redundant rings. Simplifies communication of a PC application with the SIMATIC S7-400H system.

Safeguards previous investments due to the use of existing applications and the flexible application options. No additional programming required for PC and H systems.

Increases the availability of the PC application (e.g.PC S7) through redundant communication

Ordering data
S7-REDCONNECT/Windows V1.4 } Software for fail-safe S7 communication through redundant networks incl. S7-OPC server under Windows NT 4.0 WS, server; Windows 2000 Pro, server; for CP 1613, with electronic manual on CD-ROM German/English Upgrade S7-REDCONNECT/ Windows V1.4 For expansion of S7-1613/Windows on S7-REDCONNECT/Windows V1.4, under Windows NT 4.0 WS, server; Windows 2000 Pro, server; with electronic manual on CD-ROM German/English

Order No. 6GK1 716-0HB14-3AA0

6GK1 716-0HB14-3AA4

Siemens IK PI 2001

4/135

Industrial Ethernet
System interfacing for PG/PC
CP 1612 communications processor
Overview
ISO TCP/IP PG/OP S7 C

For connection of PG/PC with PCI slot to Industrial Ethernet with 10/100 Mbit/s Communication services through ISO or TCP/IP transport protocols PG/OP communication S7 communication S5-compatible communication (SEND/RECEIVE)

Designed for use in industrial environments. PCI card Interfaces: RJ45 (Twisted Pair) Plug&Play Delivery of the communication software includes the OPC servers

S5 C

OPC

Application

The CP 1612 is an Ethernet card that can be operated in any PG/PC with a free PCI slot. It supports the Plug & Play mechanism of the operating system. The CP 1612 offers the following accesses: Layer 2: Interfacing for PC networks in an industrial environment.

It is intended for applications in an industrial environment.

The CP 1612 can be operated with all SOFTNET for Industrial Ethernet packages.

Design

Mode of operation

Layer 4 and layer 7. In conjunction with the SOFTNET packages for Industrial Ethernet, the CP 1612 offers low-cost access to Industrial Ethernet, e.g.to SIMATIC S5/S7. The configuring tool NCM PC is included in delivery with the software packages SOFTNET-S7 and SOFTNET-PG for Industrial Ethernet. NCM PC is a component of Advanced PC Configuration.

In addition, the protocols for Industrial Ethernet provided by the operating system are also supported.

Configuration

Configuration of S7 communication protocols and S5compatible communication is executed in STEP 7/ NCM PC, V5.1 SP2 or higher.

For further information on Advanced PC Configuration and the previous versions of PC/Windows software products please visit us in the Internet at:

http://www.siemens.de/ simatic-net/ik-info_en

4/136

Siemens IK PI 2001

Industrial Ethernet
System interfacing for PG/PC
CP 1612 communications processor
Designed for Industry

Connection option RJ45 Optimized for SOFTNET. Ideal for small installations.

Technical specifications
Data transfer rate Interfaces Connection to Industrial Ethernet Supply voltage Current consumption From 5 V DC Power loss Perm. ambient conditions Operating temperature Transport/storage temperature Relative humidity Design Module format Dimensions (H x D) in mm Weight Space required approx. max. 10/100 Mbit/s RJ45 +5 V DC 5% 200 mA 1W 0 C to +50 C 25 C to +55 C 95% at +25 C Short AT format 51 x 120 100 g 1 x PCI slot

Ordering data

Order No. 6GK1 161-2AA00

} CP 1612 PCI card for connection of a PG/PC to Industrial Ethernet (10/100 Mbit/s), with RJ45 connector through SOFTNET-S7 and SOFTNET-PG } SOFTNET-S7/Windows V6.0 for Industrial Ethernet Software for S5-compatible communication (SEND/RECEIVE) and S7 communication, incl. OPC server, PG/OP communication, NCM PC, up to 64 connections, under Windows NT 4.0 WS, server; Windows 2000 Pro, server for CP 1612/CP 1512 with electronic manual on CD-ROM German/English
SOFTNET-PG/Windows V6.0 for Industrial Ethernet Software for PG/OP communication, NCM PC, under Windows NT 4.0 WS, server; Windows 2000 Pro, Server for CP 1612/CP 1512, with electronic manual on CD-ROM German/English SOFTNET-PG/Windows V3.3 Software for PG/OP communication, under Windows Me, with electronic manual on CD-ROM German/English CP 1613 and SOFTNET for Industrial Ethernet manual Paper version Including: Description of interfaces (S7, S5-compatible communication), OPC server, configuring tool German English SIMATIC NET Software Update Service for Industrial Ethernet, PROFIBUS, OPC server, including manuals on CD-ROM SIMATIC NET Manual Collection Electronic manuals for communication systems, protocols, products on CD-ROM German/English

6GK1 704-1CW60-3AA0

max.

approx. approx.

6GK1 704-1PW60-3AA0

6GK1 704-1PW33-3AA0

} } }

6GK1 971-1GA00-0AA0 6GK1 971-1GA00-0AA1 6GK1 704-0AA00-3AA2

6GK1 975-1AA00-3AA0

Siemens IK PI 2001

4/137

Industrial Ethernet
System interfacing for PG/PC
CP 1512 communications processor
Overview
ISO TCP/IP PG/OP S7 C

For connection of PG/ notebooks with PCMCIA slot (CardBus interface 32 bit) to Industrial Ethernet with 10/100 Mbit/s Communication services through ISO or TCP/IP transport protocols PG/OP communication S7 communication S5-compatible communication (SEND/RECEIVE)

Designed for use in industrial environments. PCMCIA card type II Interfaces: RJ45 (Twisted Pair) Plug&Play Delivery of the communication software includes the OPC servers

S5 C

OPC

Application

CP 1512 is an Ethernet card which can be operated in any PG/PC with one a free PCMCIA slot type II with CardBus interface (32-bit).

In conjunction with all SOFTNET packages for Industrial Ethernet (except UNIX), the CP 1512 can be used (e.g.) in a notebook for remote programming (PG/OP communication).

CP 1512 is compatible with the standard PCMCIA 2.x.

Design

Supports the Plug&Play mechanism of the operating system. The CP 1512 offers the following accesses: Layer 2: Interfacing for PC networks in an industrial environment.

Mode of operation

Layer 4 and layer 7. In conjunction with the SOFTNET packages for Industrial Ethernet, the CP 1512 offers low-cost access to Industrial Ethernet, e.g. to the SIMATIC S5/S7. The configuring tool NCM PC is included in delivery with the software packages SOFTNET-S7 and SOFTNET-PG for Industrial Ethernet. NCM PC is a component of Advanced PC Configuration.

In addition, the protocols for Industrial Ethernet provided by the operating system are also supported.

Configuration

Configuration of S7 communication protocols and S5compatible communication is executed in STEP 7/ NCM PC, V5.1 SP2 or higher.

For further information on Advanced PC Configuration and the previous versions of PC/Windows software products please visit us in the Internet at:

http://www.siemens.de/ simatic-net/ik-info_en

4/138

Siemens IK PI 2001

Industrial Ethernet
System interfacing for PG/PC
CP 1512 communications processor
Configuration

Production Level
PC with CP 1613 and WinCC

Control Room
PG/Notebook with CP 1512

S7-400

max. 10 m TP Cord 9 / RJ45 Outlet RJ45

ESM ITP80

ESM

FC Standard Cable

ITP Standard Cable 9/15

Fig. 4/64 System configuration with CP 1512

TP Cord 9 / RJ45

Outlet RJ45

G_IK10_deI0068s

Designed for Industry

Connection option RJ45 Optimized for SOFTNET

Ideal for small installations Implementation in PGs/notebooks with PCMCIA/CardBus interface

Siemens IK PI 2001

4/139

Industrial Ethernet
System interfacing for PG/PC
CP 1512 communications processor
Technical specifications
Data transfer rate Interfaces Connection to Industrial Ethernet Connection to PG/PC Supply voltage Current consumption Perm. ambient conditions Operating temperature Transport/storage temperature Relative humidity Construction of the CP 1512 Module format Dimensions (H x W x D) in mm Weight Space required Construction of adapter Dimensions (W x H x D) in mm approx. Weight approx. Cable length approx. max. 10/100 Mbit/s RJ45 PCMCIA Slot type II (CardBus 32 bit) 3.3 V DC, 5% 0.18 A 0 C to +55 C 20 C to +80 C 90% at +25 C PCMCIA type II 85.6 x 54 x 5 30 g 1 x PCMCIA slot type II RJ45 40 x 22 x 20 40 g 20 cm

Ordering data

Order No. 6GK1 151-2AA00

} CP 1512 PCMCIA card (CardBus 32 bit) for connection of PG/PC to Industrial Ethernet incl. adapter for RJ45, through SOFTNET-S7 and SOFTNET-PG

max.

} 6GK1 704-1CW60-3AA0 SOFTNET-S7/Windows V6.0 for Industrial Ethernet Software for S5-compatible communication (SEND/RECEIVE) and S7 communication, incl. OPC server, PG/OP communication, NCM PC, up to 64 connections, under Windows NT 4.0 WS, server; Windows 2000 Pro, server for CP 1612/CP 1512 with electronic manual on CD-ROM German/English
SOFTNET-PG/Windows V6.0 for Industrial Ethernet Software for PG/OP communication, NCM PC, under Windows NT 4.0 WS, server; Windows 2000 Pro, Server for CP 1612/CP 1512, with electronic manual on CD-ROM German/English SOFTNET-PG/Windows V3.3 Software for PG/OP communication, under Windows Me, with electronic manual on CD-ROM German/English SIMATIC NET Software Update Service for Industrial Ethernet, PROFIBUS, OPC server, including manuals, on CD-ROM, German/English CP 1613 and SOFTNET for Industrial Ethernet manual Paper version includes: Description of interfaces (S7, S5-compatible communication), OPC server, configuration German English SIMATIC NET Manual Collection Electronic manuals for communication systems, protocols, products on CD-ROM German/English

6GK1 704-1PW60-3AA0

6GK1 704-1PW33-3AA0

6GK1 704-0AA00-3AA2

} } }

6GK1 971-1GA00-0AA0 6GK1 971-1GA00-0AA1 6GK1 975-1AA00-3AA0

4/140

Siemens IK PI 2001

Industrial Ethernet
System interfacing for PG/PC
SOFTNET for Industrial Ethernet
Overview
ISO TCP/IP PG/OP S7 C
CP 1512 CP 1612 PC/PG SOFTNET for Industrial Ethernet

For connecting programming devices/PCs/ workstations with automation systems. Communication services: PG/OP communication S7 communication S5-compatible communication (SEND/RECEIVE) Can be used in conjunction with CP 1612 (PCI), CP 1512 (PCMCIA) Modem (Remote Access Service RAS)

S5 C

OPC

Industrial Ethernet
S5-115U to -155U with CP 1430 TF S7-400 with CP 443-1
G_IK10_deI0040s

S7-300 with CP 343-1

Complete protocol stack as software package. OPC servers are included in delivery of the communication software SOFTNET is available for the following interfaces: CP 1612 (PCI card) CP 1512 (PCMCIA card). Modem (RAS)

Fig. 4/65 SOFTNET for Industrial Ethernet system configuration

Application

Using SOFTNET for Industrial Ethernet PG/PC/Workstations can be coupled with programmable controllers, e.g. SIMATIC S7, through Industrial Ethernet.

The following are available as user interfaces: PG/OP communication for SIMATIC S7 S5-compatible communication (SEND/RECEIVE) for communication with SIMATIC S7 S7 communication Unlike the 1613 products, the performance capability of the SOFTNET packages with this The following compilers can therefore be used in conjunction with the SIMATIC NET products: Microsoft Visual C/C++ V6.0 Microsoft Visual Basic V6.0 Other compilers can be implemented through the OPC server, however, the compiler must support the COM interface (Microsoft Component Object Model) Software for PG/OP communication This software allows programming of the SIMATIC S5 and S7 controllers through Industrial Ethernet in conjunction with STEP 5/STEP 7. Software for S7 communication SIMATIC S7 system components communicate with each other through S7 communication. The S7 communications can optionally be based on the ISO protocol or the TCP/IP protocol.

Mode of operation

SOFTNET processes the complete protocol stack in the PC.

architecture depends on the network extension and/or workload of the PC used. S7 communication offers the following services: Administrative services S7 connection management services Variables services VFD (virtual field device) services Trace and Mini database. S5-compatible communication (SEND/RECEIVE) This layer 4 based interface (ISO transport or TCP/IP with RFC 1006) is used for communication between PG/PC and SIMATIC S5 PG/PC and SIMATIC S7 PG/PC and PG/PC S5-compatible communication (SEND/RECEIVE) provides the following services: Management services Connection establishment services Data transfer services

Functions

User interfaces OPC interface The OPC server contained in the respective software package can be used as a standard programming interface for the protocols S7 communication and S5-compatible communication to connect automation applications to OPC-capable Windows applications (Office, HMI systems etc.). Programming interface through C library The programming interfaces for the protocols S7 communication, PG/OP communication, S5-compatible communication and TF protocol for existing applications are implemented as a Dynamic Link Library (DLL).

Siemens IK PI 2001

4/141

Industrial Ethernet
System interfacing for PG/PC
SOFTNET for Industrial Ethernet
Configuration

The complete configuration of S7 communication protocols and S5-compatible communication is executed in STEP 7/NCM PC, V5.1 SP2 or higher.

NCM PC is a component of Advanced PC Configuration. The configuring tool NCM PC is included in delivery of the relevant software packages.

For further information on Advanced PC Configuration and the previous versions of PC/Windows software products please visit us in the Internet at:

http://www.siemens.de/ simatic-net/ik-info_en

Designed for Industry

Communication with SIMATIC through standard Ethernet cards (NE 2000-compatible).

Can be used in notebooks with PCMCIA slot. Optimized for small installations.

Technical specifications
Performance data S7 and PG/OP communication SOFTNET-S7: Number of operable connections

Ordering data

Order No. 6GK1 704-1CW60-3AA0

max.

} SOFTNET-S7/Windows V6.0 for Industrial Ethernet Software for S5-compatible communication (SEND/RECEIVE) and S7 communication, incl. OPC server, PG/OP communication, NCM PC, up to 64 connections, under Windows NT 4.0 WS, server; Windows 2000 Pro, server for CP 1612/CP 1512 with electronic manual on CD-ROM German/English
SOFTNET-PG/Windows V6.0 for Industrial Ethernet Software for PG/OP communication, NCM PC, under Windows NT 4.0 WS, server; Windows 2000 Pro, Server for CP 1612/CP 1512, with electronic manual on CD-ROM German/English SOFTNET-PG/Windows V3.3 Software for PG/OP communication, under Windows Me, with electronic manual on CD-ROM German/English CP 1613 and SOFTNET for Industrial Ethernet manual Paper version Including: Description of interfaces (S7, S5-compatible communication), OPC server, configuring tool German English SIMATIC NET Manual Collection Electronic manuals for communication systems, protocols, products on CD-ROM German/English SIMATIC NET Software Update Service for Industrial Ethernet, PROFIBUS, OPC server, including manuals on CD-ROM

6GK1 704-1PW60-3AA0

6GK1 704-1PW33-3AA0

} } }

6GK1 971-1GA00-0AA0 6GK1 971-1GA00-0AA1 6GK1 975-1AA00-3AA0

6GK1 704-0AA00-3AA2

4/142

Siemens IK PI 2001

WCA Faceplate Analog en
No ratings yet
WCA Faceplate Analog en
71 pages
Lab. Management
No ratings yet
Lab. Management
36 pages
S 7
No ratings yet
S 7
295 pages
WinCC TIA Portal Soap DOC en
No ratings yet
WinCC TIA Portal Soap DOC en
10 pages
APACS Architecture PDF
No ratings yet
APACS Architecture PDF
12 pages
3 - Siemens Open Library - Example Object Configuration V1.4
No ratings yet
3 - Siemens Open Library - Example Object Configuration V1.4
24 pages
Siemens SIMATIC Step 7 Programmer
No ratings yet
Siemens SIMATIC Step 7 Programmer
72 pages
Dream Report User Manual PDF
No ratings yet
Dream Report User Manual PDF
496 pages
Apacs M Bus M Net Interface Installation For Windows 2000 and NT Personal Computers - Compress
No ratings yet
Apacs M Bus M Net Interface Installation For Windows 2000 and NT Personal Computers - Compress
74 pages
Dynamic Wizard
No ratings yet
Dynamic Wizard
348 pages
As IEC 61131.2-2004 Programmable Controllers Equipment Requirements and Tests
No ratings yet
As IEC 61131.2-2004 Programmable Controllers Equipment Requirements and Tests
14 pages
01 System Overview en
No ratings yet
01 System Overview en
20 pages
HMI Toolbox WinCC Professional V15.1 DOC en PDF
No ratings yet
HMI Toolbox WinCC Professional V15.1 DOC en PDF
112 pages
ModbusRTUControl W ML1100 PDF
No ratings yet
ModbusRTUControl W ML1100 PDF
11 pages
PROFIBUS Slave Step7 2.1
No ratings yet
PROFIBUS Slave Step7 2.1
30 pages
Pcs7 Compendium Part B en-US en-US
No ratings yet
Pcs7 Compendium Part B en-US en-US
186 pages
TIA MICRO1 10E Connecting HMI KTP600
No ratings yet
TIA MICRO1 10E Connecting HMI KTP600
23 pages
SIMATIC Process Historian and Reporting - 2014 - EN
100% (1)
SIMATIC Process Historian and Reporting - 2014 - EN
24 pages
Sce en 090-010 R1209 S7-300 Hmi TP700
No ratings yet
Sce en 090-010 R1209 S7-300 Hmi TP700
118 pages
Brochure Course TIA Portal Wincc (TIA-WCCM)
No ratings yet
Brochure Course TIA Portal Wincc (TIA-WCCM)
2 pages
Ps7Migrate v6 To v8
No ratings yet
Ps7Migrate v6 To v8
84 pages
Sce 072 100 Safety PN Cpu1516f Et200sp r2101 en
No ratings yet
Sce 072 100 Safety PN Cpu1516f Et200sp r2101 en
96 pages
Alarm Hiding DOC PCS7 V90SP1 en
No ratings yet
Alarm Hiding DOC PCS7 V90SP1 en
36 pages
Simatic S7
No ratings yet
Simatic S7
22 pages
TF6271 TC3 Profinet RT Controller EN
No ratings yet
TF6271 TC3 Profinet RT Controller EN
72 pages
Configuracion Sinamics PCS7 PDF
No ratings yet
Configuracion Sinamics PCS7 PDF
21 pages
Getting Started MC 10
No ratings yet
Getting Started MC 10
25 pages
S7 SCL Readme
No ratings yet
S7 SCL Readme
23 pages
252 SiPass Int MP2 65SP2 RelNotes A-100083-1 en A
100% (1)
252 SiPass Int MP2 65SP2 RelNotes A-100083-1 en A
40 pages
SP-DRM-ZWS_V160102-151-200
No ratings yet
SP-DRM-ZWS_V160102-151-200
50 pages
PCS 7 V9.0 SP1 Basic Library - 12 - 2017
No ratings yet
PCS 7 V9.0 SP1 Basic Library - 12 - 2017
498 pages
Tia Pro1 12 Connecting Hmi
No ratings yet
Tia Pro1 12 Connecting Hmi
27 pages
Ecodrive Final
No ratings yet
Ecodrive Final
24 pages
CP342-5 DP Master Slave en
No ratings yet
CP342-5 DP Master Slave en
12 pages
Tag and Alarm Export Manual
No ratings yet
Tag and Alarm Export Manual
46 pages
Starter
No ratings yet
Starter
18 pages
TIA MICRO1 12E Training and Support
No ratings yet
TIA MICRO1 12E Training and Support
21 pages
Logix AOI For Modbus TCP - The Reynolds Company - Blog
No ratings yet
Logix AOI For Modbus TCP - The Reynolds Company - Blog
3 pages
Bibliothek Screens G120 en
No ratings yet
Bibliothek Screens G120 en
26 pages
BRAUMAT Operator Manual V3 en
No ratings yet
BRAUMAT Operator Manual V3 en
75 pages
Motion Control NC62 Complete English 2019
No ratings yet
Motion Control NC62 Complete English 2019
796 pages
D4x5 2 Commissioning en US
No ratings yet
D4x5 2 Commissioning en US
394 pages
SMC Flex With Datalinks - D735 Devicenet - Option
No ratings yet
SMC Flex With Datalinks - D735 Devicenet - Option
5 pages
DCC Configuring
No ratings yet
DCC Configuring
176 pages
PM-ANALYZE_New
No ratings yet
PM-ANALYZE_New
48 pages
SCE EN 030-030 R1209 Datenbausteine PDF
No ratings yet
SCE EN 030-030 R1209 Datenbausteine PDF
31 pages
d11 cp342 cp342 PDF
No ratings yet
d11 cp342 cp342 PDF
38 pages
Microsoft Power Point - 03 WinCC V7 Graphic
100% (1)
Microsoft Power Point - 03 WinCC V7 Graphic
60 pages
SIMATIC PCS 7 Cabinet Design: 6/2 6/2 6/3 Basic Cabinet 6/4 ET 200M I/O Unit 6/5 System Unit
No ratings yet
SIMATIC PCS 7 Cabinet Design: 6/2 6/2 6/3 Basic Cabinet 6/4 ET 200M I/O Unit 6/5 System Unit
6 pages
3500 - 42M Proximitor - Seismic Monitor Datasheet
No ratings yet
3500 - 42M Proximitor - Seismic Monitor Datasheet
20 pages
DP ASi Link 20E - en - 2008 08 - Manual - C79000 G8976 C235 01
No ratings yet
DP ASi Link 20E - en - 2008 08 - Manual - C79000 G8976 C235 01
144 pages
S7-PLCSIM - Testing Your S7-CPU Programs - Manual
No ratings yet
S7-PLCSIM - Testing Your S7-CPU Programs - Manual
93 pages
p03 02 Vertical Integration With Opc v9 Tud 0719 en
No ratings yet
p03 02 Vertical Integration With Opc v9 Tud 0719 en
34 pages
Tia Portal
No ratings yet
Tia Portal
15 pages
Pcs7Ase - ST Pcs7Ose - ST Pcs7Srv - ST Cemate - ST
No ratings yet
Pcs7Ase - ST Pcs7Ose - ST Pcs7Srv - ST Cemate - ST
1 page
DeviceNet The Ultimate Step-By-Step Guide
From Everand
DeviceNet The Ultimate Step-By-Step Guide
Gerardus Blokdyk
No ratings yet
NTP Siemens
No ratings yet
NTP Siemens
347 pages
S7-PCT - Readme
No ratings yet
S7-PCT - Readme
10 pages
SIMATIC NET Commissioning PC Stations - Manual
No ratings yet
SIMATIC NET Commissioning PC Stations - Manual
221 pages
Cours WinCC
100% (5)
Cours WinCC
239 pages
Simatic-Advancedpdf PDF
100% (1)
Simatic-Advancedpdf PDF
268 pages
Navigation A-320 PDF
No ratings yet
Navigation A-320 PDF
53 pages
City Cooler Datasheet ctc02 May 2023
No ratings yet
City Cooler Datasheet ctc02 May 2023
4 pages
Data-Driven Evolutionary Modeling in Materials Technology 1st Edition Nirupam Chakraborti - Explore the complete ebook content with the fastest download
100% (1)
Data-Driven Evolutionary Modeling in Materials Technology 1st Edition Nirupam Chakraborti - Explore the complete ebook content with the fastest download
72 pages
8086 Microprocessor
No ratings yet
8086 Microprocessor
15 pages
TC303 Thermostat For Hotel, Modbus Networking
No ratings yet
TC303 Thermostat For Hotel, Modbus Networking
4 pages
DMAIC Is Model That Is Data
No ratings yet
DMAIC Is Model That Is Data
1 page
Configuration Migration Utility
No ratings yet
Configuration Migration Utility
2 pages
Big Data Analytics For Gold Price Forecasting Based On Decision Tree Algorithm and Support Vector Regression (SVR)
No ratings yet
Big Data Analytics For Gold Price Forecasting Based On Decision Tree Algorithm and Support Vector Regression (SVR)
6 pages
A1 PQ Control Strategy For Voltage-Controlled Inverters Applied in Low-Voltage Power System
No ratings yet
A1 PQ Control Strategy For Voltage-Controlled Inverters Applied in Low-Voltage Power System
4 pages
6685 PDF
100% (2)
6685 PDF
2 pages
Assignments For Week 5 2024
No ratings yet
Assignments For Week 5 2024
10 pages
University of Georgia Dissertation Format
100% (2)
University of Georgia Dissertation Format
8 pages
Adding Turbo To VR6 3.2 QA #4
No ratings yet
Adding Turbo To VR6 3.2 QA #4
9 pages
Final Estimate For Tender
No ratings yet
Final Estimate For Tender
195 pages
Ma28 Brochure
No ratings yet
Ma28 Brochure
2 pages
Prestress Construction Information Checklist
No ratings yet
Prestress Construction Information Checklist
3 pages
NR8961 2+0 Configuration Steps
No ratings yet
NR8961 2+0 Configuration Steps
11 pages
20CSE027 Shakil Ahmed
No ratings yet
20CSE027 Shakil Ahmed
11 pages
Aarti Saswat Documentation
No ratings yet
Aarti Saswat Documentation
28 pages
Enerjet Ejc Hi-Velocity Burners Gas, Oil or Combination
No ratings yet
Enerjet Ejc Hi-Velocity Burners Gas, Oil or Combination
6 pages
Spray-Dryer-SD-06-and-SS-07-Brochure-2013
No ratings yet
Spray-Dryer-SD-06-and-SS-07-Brochure-2013
1 page
PDF Extra Help
No ratings yet
PDF Extra Help
3 pages
Conventional Detection Devices: Photoelectric Smoke Detector
No ratings yet
Conventional Detection Devices: Photoelectric Smoke Detector
3 pages
Chapter 12 Bode Plots
No ratings yet
Chapter 12 Bode Plots
39 pages
8 WATER CONSUMPTION AND WATER DEMAND
100% (1)
8 WATER CONSUMPTION AND WATER DEMAND
9 pages
Unit 06 - Assignment Brief 1 - Digital Transformation - 082022
No ratings yet
Unit 06 - Assignment Brief 1 - Digital Transformation - 082022
3 pages
Introduction of Software v20.0
No ratings yet
Introduction of Software v20.0
55 pages
Get From EKYCBiometric PDF
No ratings yet
Get From EKYCBiometric PDF
1 page
Umawit Ang Bayan Sheet Music For Soprano, Alto, Tenor, Bass Voice (Choral)
No ratings yet
Umawit Ang Bayan Sheet Music For Soprano, Alto, Tenor, Bass Voice (Choral)
1 page