F-Series Super Duty Truck

E-Series Econoline Van

Features, Descriptions,
Unique Service Procedures
and General Diagnostics

6.0LPower Stroke Diesel

 F O R WA R D
This publication is intended to provide technicians and service personnel with an overview of technical advancements in the
6.0L POWER STROKE  Diesel Engine. The information contained in this publication will supplement information contained in
available service literature.

I M P O R TA N T S A F E T Y N O T I C E
Appropriate service methods and proper repair procedures are essential for the safe,
reliable operation of all motor vehicles, as well as, the personal safety of the individual
performing the work. This manual provides general directions for accomplishing service
repair work with tested, effective techniques. Following the directions will assure
reliability. There are numerous variations in the procedures; techniques, tools, parts for
servicing vehicles and the skill of the individual doing the work. This manual cannot
possibly anticipate all such variations and provide advice or cautions as to each.
Accordingly, anyone who departs from the instructions provided in this manual must first
establish that they do not compromise their personal safety or the vehicle integrity by
their choice of methods, tools or parts.

The following list contains some general WARNINGS that you should follow when you
work on a vehicle.

Always wear safety glasses for eye protection.

Use safety stands whenever a procedure requires you to be under the vehicle.

Be sure that the ignition switch is always in the OFF position, unless otherwise required
by the procedure.

Never perform any service to the engine with the air cleaner removed and the engine
running unless a turbocharger compressor inlet shield is installed.

Set the parking brake when working on the vehicle. If you have an automatic
transmission, set it in PARK unless instructed otherwise for a specific service operation.
If you have a manual transmission, it should be in REVERSE (engine OFF) or
NEUTRAL (engine ON) unless instructed otherwise for a specific service operation.

Operate the engine only in a well-ventilated area to avoid the danger of carbon
monoxide.

Keep yourself and your clothing away from moving parts when the engine is running,
especially the fan, belts, and the turbocharger compressor.

To prevent serious burns, avoid contact with hot metal parts such as the radiator,
turbocharger pipes, exhaust manifold, tail pipe, catalytic converter and muffler.

Do not smoke while working on the vehicle.

To avoid injury, always remove rings, watches, loose hanging jewelry, and loose clothing
before beginning to work on a vehicle. Tie long hair securely behind the head.

Keep hands and other objects clear of the radiator fan blades.

1
 6 . 0 L P O W E R S T R O K E

2
 6 . 0 L P O W E R S T R O K E
TA B L E O F C O N T E N T S
OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
H o r s e p o w e r & To r q u e . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

C O M P O N E N T L O C AT I O N . . . . . . . . . . . . . . . . . . 7
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

RUNNING 2003 CHANGES . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Turbocharger Oil Supply Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Wiring Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

AIR MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

External Mounted Crankcase Breather . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Intake Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
EGR Throttle Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

FUEL MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Wavy High Pressure Oil Rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
ICP Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
DLC Coated Injector Plunger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

ELECTRICAL COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . .29

Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

ECONOLINE 6.0L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Component Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Lubrication System Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Fuel System Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

SERVICE TIPS/DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . . . .43

APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

3
4
 1

6.0L
POWER STROKE V8


DIRECT INJECTION
TURBOCHARGED
DIESEL ENGINE
5
 
6.0L POWER STROKE DIESEL
6.0L Power Stroke Engine

• This Publication is not intended to replace

6.0L Power Stroke 
the Service Manual but to introduce the
updates to the 6.0L Power Stroke engine.
Direct Injection Turbocharged
Diesel Engine

• 2003 Mid-Year Improvements

• 2004 Running Changes and Updates
• 2004 6.0L Econoline
• Updated 6.0L Engine Specifications

2
New 6.0L Engine Features
Update Features
• Due to more stringent federal emissions
standards, the 6.0L Power Stroke engine
has undergone many updates during the
2004 model year.
• EGRTP (Exhaust Gas Recirculation Throttle

• The 6.0L Power Stroke engines are Plate)
manufactured at two locations: Indianapolis
Engine Plant in Indianapolis, Indiana and • Redesigned High-Pressure Oil Rail and
International Diesel of Alabama in Huntsville, Delivery System
Alabama. The serial number breaks for the
updated 2004 6.0L engines are 6155637 for • Redesigned EGR Cooler
Indianapolis built engines and 0094580 for
Huntsville built engines. • DLC Coating on Injector Plunger
• The begining production date for the
updated 2004 Power Stroke engine
was on September 29, 2003.
3
Horsepower and Torque
Horsepower and Torque
• Horsepower and torque will remain
unchanged throughout the 2004 model year
on F-Series Super Duty trucks.

• The 6.0L Power Stroke engine creates 325
HP at 3300 RPM and 560 ft/lb of torque at
2000 RPM.

4
6
 C O M P O N E N T L O C AT I O N
Left Front of Engine
2 3 1
1. FICM (Fuel Injection Control Module)
Mounting Brackets

2. EGR Throttle Position Sensor

3. FICM (Fuel Injection Control Module)

5
Left Rear of Engine

3 1. Crankcase Breather

2. Glow Plug Harness

3. Rear FICM mounting bracket

6
7
 C O M P O N E N T L O C AT I O N S
Right Rear of Engine
2 3
1. Glow Plug Harness

2. Emissions Label

3. Glow Plug Control Module (GPCM)

7
Right Front of Engine

1. ICP Sensor
1 3 2
2. EGRTP (EGR Throttle Plate) Actuator

3. GPCM bracket

8
8
 C O M P O N E N T L O C AT I O N
Top of Engine

1. EGR Cooler
2
3 2. Intake Manifold

3. Compressor Inlet Hose

9
Upper Oil Pan

• The six M8 bolts which were placed in the

center of the upper oil pan have been
eliminated.

• Additional strength has been cast into the

upper oil pan.

• An upper oil pan which has bolt holes

present should always be assembled with
ELIMINATED BOLTS the six specified M8 bolts. Failure to do so
will result in a vibration related noise caused
from the upper oil pan vibrating against the
bed plate.

• An upper oil pan which has had the bolt

holes eliminated, can be utilized as a service
part to replace the earlier part.

10
9
 
2 0 0 4 P O W E R S T R O K E F E AT U R E S
Camshaft

• The lobe separation angle, lobe lift, and

duration have changed to improve
combustion characteristics.

• Changes have been made to the camshaft

to increase the efficiency of the 6.0L engine,
allowing it to meet tighter emissions
standards.

• It is not recommended that the updated 2004

MY camshaft be installed into an earlier
version of the 6.0L engine. Emissions will be
impacted.

11
Piston/Combustion Chamber
ORIGINAL UPDATED
• The combustion chamber on the piston has BOWL DESIGN BOWL DESIGN
been modified.

• This modification increases the efficiency of

the combustion process, allowing the 6.0L
engine to meet tighter emissions standards.

12
Glow Plugs

• Due to the design change of the piston, the

glow plug has been made shorter by 1.2
mm.

• NOTE: If the longer glow plugs are

installed into an engine with updated
pistons, glow plug to piston contact will 1.2 mm
result, ending in potential catostrophic
engine failure.
13
10
 
2 0 0 4 P O W E R S T R O K E F E AT U R E S
Water Pump/Front Cover

90mm 100mm • The water pump impeller diameter has

increased in size to 100 mm from 90 mm.

• The larger impeller will increase coolant flow

through the engine which will offset higher
heat rejection.

• Note: Both water pumps have the same

bolt pattern, but a different sealing area.
As a result, the smaller water pump has
the physical ability to be installed into an
updated front cover. If this is done, a
coolant leak and over heating of the
engine may result.

14
FICM (Fuel Injection Control Module)
Brackets
FICM ELECTRICAL CONNECTORS
• The FICM brackets are now composed of
two bottom pieces and two smaller top
pieces. The bottom brackets are pictured
here. They slide over valve cover bolt studs
as did the previous brackets.
X-3 X-2 X-1
• The new brackets have larger vibration
insulators at each valve cover mounting
point.

FICM MOUNTING BRACKETS

15
GPCM (Glow Plug Control Module)
Bracket
• The GPCM bracket has been modified to
accept the repositioning of the ICP Sensor.

ICP SENSOR • An earlier GPCM bracket will not work on an

updated 2004 MY engine.

GPCM MOUNTING BRACKET

16
11
 NOTES

12
 2003 MY RUNNING CHANGES
Turbocharger Oil Supply Line

• Part way through the 2003 model year, the

turbo oil supply line changed in design.

• The early design was a quick-connect/

disconnect style (left). The improved design
(right) provides a larger o-ring seal and is
held in place with a bolted down collar.
QUICK CONNECT • The new design improves the line’s long
FITTING term reliability and reduces risk of oil leaks
between the oil cooler assembly and the
supply line.

HOLD DOWN
COLLAR
17
Turbocharger Oil Supply Line:
Installation
• First, apply oil to the oil supply line o-ring.

• Orient the supply line where it will be

positioned once fully installed.

• Press the supply line/o-ring into the cooler.

OIL COOLER

18
Turbocharger Oil Supply Line:
Installation
• Once the oil supply line has been pressed
into the cooler, the collar should be
positioned and the retaining bolt installed.

• Prior to tightening the retaining bolt,

reposition the oil supply line, as necessary,
HOLD DOWN BOLT in order to install the two turbo mounted oil
supply line bolts, located on the center
section of the turbo.

• Torque all bolts to specification.

19
13
 2003 MY RUNNING CHANGES
Wiring Harness Routing
*Early Production 2003
• From the beginning of the production of the
6.0L Power Stroke engine, the wiring
harness has been comprised of two
combined smaller harnesses.

• Both of these smaller harnesses were

routed between the oil filter housing and the
secondary fuel filter housing.

20
*Late Production 2003 and 2004 MY

• In order to increase serviceability and long INJECTOR HARNESS

term reliability of the engine wiring harness,
the two harnesses were separated.

• The injector harness, which runs from the

FICM to each of the eight injectors, is now
routed between the oil filter housing and the
compressor housing of the turbocharger.

*2004 engine shown 21

Injector Clip Orientation

• The orientation of the injector connector

retaining clip has been repositioned in order
to improve serviceability.

• Prior to this change, the clip was positioned

on the side (9 o’clock position) of the
connector. This made removal and
installation of the injector connector more
difficult on some cylinders.

9 O’CLOCK CLIP 12 O’CLOCK CLIP

22
14
 2003 MY RUNNING CHANGES
High-Pressure Pump Cover with
Sleeve

• From the beginning of production, the high-

pressure pump cover retains a sleeve which
provides a sealing surface for the o-ring on
SLEEVE the high-pressure oil discharge tube.

23
High-Pressure Pump Cover without
Sleeve

• Mid-way through 2003 MY, the sleeve in the

high-pressure pump cover was removed.
NO SLEEVE • The sealing surface for the high-pressure oil
discharge tube is now totally machined for
the o-ring seal.

24
Injector Clevis

• A change was made to the injector clevis

mid-way through the 2003 MY.

• The revised clevis in the injector improves

the lateral support of the plunger and
dramatically reduces injector scuffing.

OLD CLEVIS NEW CLEVIS

25
15
 NOTES

16
 AIR MANAGEMENT SYSTEM
Air Management System Features
6.0L Air Management • The crankcase breather has been externally
System Features mounted on the left valve cover.

• The rear cross over section has been

removed from the intake manifold
• External Mounted Crankcase Breather
• The updated 2004 MY Power Stroke
• Redesigned Intake Manifold engine has been equipped with a EGR
Throttle Plate.
• Improved Turbocharger Sound
Characteristics
• Redesigned EGR Cooler.

26
Air Management System Flow
FROM CHARGE AIR COOLER
THROTTLE BODY

COMPRESSOR INLET

EGR VALVE

COMPRESSOR
OUTLET

TURBINE OUTLET

EGR COOLER

27

17
 AIR MANAGEMENT SYSTEM
Compressor Inlet Hose/Crankcase INTERNAL BREATHER
Breather Hose
• In order to accommodate the change from
an internal crankcase breather to an
externally mounted crankcase breather, the
compressor inlet hose has been modified.

• The compressor inlet hose bracket is also

utilized as a retaining bracket for the front
two mounting points of the FICM.
EXTERNAL BREATHER

28
Compressor Inlet Hose: Removal

• To disconnect the crankcase ventilation tube

from the engine, remove the air inlet tube
from the compressor inlet and rotate the
vent hose counter clockwise until it releases.


• Note: Since the 6.0L POWER STROKE
engine uses a closed crankcase
ventilation system, it is normal to see oil
carry over in the inlet air system.

CRANKCASE BREATHER HOSE

29
External Mounted Crankcase
Breather FICM MOUNTING BRACKETS

• The crankcase breather was externally

mounted on the valve cover because of the
redesign of the high-pressure oil rail.

CRANKCASE BREATHER

30
18
 AIR MANAGEMENT SYSTEM
Intake Manifold

• The intake manifold has been modified for

the updated 2004 MY.

• The cross over section at the rear of the

manifold has been eliminated.

NO REAR CROSS OVER

31
EGR Throttle Plate

• The intake manifold is now equipped with an

EGR throttle plate.

• The purpose of this plate is to lower the

manifold pressure which will allow exhaust
gases from EGR to flow freely into the
intake manifold.

• NOTE: The PCM will activate the EGRTP

EGR THROTTLE PLATE actuator and perform a full sweep of the
throttle plate for each key cycle with the
IAT temperature greater than 0 degrees
Celsius (32 deg. F.)

32
Turbocharger Exhaust Turbine Wheel

• Three fins have been added to the turbine

wheel of the turbocharger.
TURBINE BLADES
• These additional fins were added to the
turbine wheel in order to improve the
turbocharger’s sound characteristics.

33
19
 AIR MANAGEMENT SYSTEM
EGR Coolers

• The EGR cooler has been lengthened for the

updated 2004 MY engine.

• The changes to the EGR cooler will cause

the exhaust gases to be cooler before
entering into the intake manifold.

LONGER EGR COOLER

34
EGR Cooler Exhaust Connection

• Because the new EGR cooler is longer than

SHORTER EXHAUST EXTENSION
the original, the exhaust up-pipe is shorter in
length at the EGR cooler connection than
the original up-pipe.

• The new EGR cooler still utilizes the same

v-band clamp.

35
Updated EGR Cooler Mounting

• With exception to the exhaust up-pipe

connection, the updated 2004 EGR cooler
installs in the same location as the original EGR COOLER COOLANT SUPPLY
EGR cooler.

EGR COOLER
EXHAUST CONNECTION

36
20
 AIR MANAGEMENT SYSTEM
EGR Cooler: Cooling System Flow

• Coolant flows out of the filter base and into

the EGR cooler through a tube that directs
the coolant to the back of the EGR cooler.

• Coolant flows through the EGR cooler and

removes heat from the exhaust gasses
before the gasses arrive at the EGR valve.

• Coolant exits the front of the EGR cooler and

enters the coolant passage of the intake
manifold. The intake manifold directs the
coolant back into the front cover.

37
Turbocharger Mounting Bolt

REAR TURBO MOUNTING BOLT • The turbo mounting joints have been
modified. The mounting bolts no longer need
spacers on the new turbo.

38
Turbocharger Mounting Bracket

• A new turbo mounting bracket has been

implemented with the mounting bolt spacers
incorporated into the bracket. These
spacers are utilized to achieve the
necessary clamp load on the turbocharger
mounting bolts.
SPACERS
NO SPACERS

39
21
 NOTES

22
 FUEL MANAGEMENT SYSTEM
High-Pressure Oil System

6.0L High-Pressure
• The high-pressure oil rail has been
Oil System redesigned to increase oil capacity and to
reduce noise.

• The stand pipes’ serviceability has been

• Wavy High-Pressure Oil Rail improved.

• Redesigned Stand Pipe/Branch Tube • The ICP sensor has been relocated to the
right valve cover/high-pressure rail.
• Relocated ICP Sensor
• DLC (Diamond Like Carbon) coated
• DLC Coated Injectors injectors.

40
High-Pressure Oil System Flow

HIGH PRESSURE STAND PIPE

HIGH PRESSURE
OIL RAIL

HIGH PRESSURE OIL BRANCH TUBE

RE
AR
OF
EN
GIN
E
41

23
 FUEL MANAGEMENT SYSTEM
Wavy High-Pressure Rail
FRONT PORT
• The high-pressure rail has been redesigned
REAR PORT
to reduce noise through the high-pressure
oil system.

• The volume wavy high-pressure rail has

increased from 15 cubic inches to 30 cubic
inches. This reduces pressure fall-off during
injection and improved emissions and fuel
economy.

• NOTE: The larger volume oil rail will

increase engine start time after the high-
pressure oil rail has been drained during
the process of any repairs.
HIGH-PRESSURE OIL RAIL

*Right bank shown. 42

Wavy High-Pressure Oil Rail with
Dual AWA Fittings RAIL END CAPS
• The wavy high-pressure oil rail has special
AWA (Acoustic Wave Attenuation) features
to dampen hydraulic noises. AWA FITTINGS
• The wavy high-pressure rail uses two AWA
fittings, a large one and a small one. The
AWA fittings are placed in the center of the
rail. The smaller AWA fitting is placed in the
wavy portion of the rail while the larger AWA
fitting is placed in the original portion of the
rail.

• The wavy high-pressure rail utilizes four

specially designed end caps in conjunction
with the AWA fittings.

43
High-Pressure Stand Pipe

• The high-pressure stand pipe is a two piece

pipe that is sealed to the high-pressure rail
and high-pressure branch by o-rings.

• The stand pipe is installed after the new

wavy high-pressure oil rail has been
installed and torqued to specification.
STAND PIPE
• The stand pipe has a check valve inside to
limit hydraulic disturbance (feed back from
injector operation).

• NOTE: Do not disassemble the high-

pressure stand pipe. This will cause
damage to the internal components of
the pipe. If at any point, a stand pipe is
disassembled, discard and replace it.
44
24
 FUEL MANAGEMENT SYSTEM
High-Pressure Rail Plugs
FRONT PORT PLUG
• There are two new high-pressure oil rail
plugs introduced with the redesign of the
rail.

• The rear supply-port plug (on the right)

allows high-pressure oil to flow into the high-
pressure rail.

• The same high-pressure oil rail is used on

both banks of the engine. As a result the
front port plug (on the left) is used to block
off the non-utilized supply port in the high-
pressure oil rail.

REAR SUPPLY-PORT PLUG

45
Rear Supply-Port Plug

REAR SUPPLY-PORT PLUG • The rear supply-port plug is located towards

the rear of engine on the high-pressure rail.
It’s purpose is to allow high-pressure oil to
flow into the high-pressure rail.

• During engine operation, a small gap

remains between the rear supply-port plug
and the stand pipe. The force of the
hydraulic pressure keeps the stand pipe
seated into the branch tube.

• The plug will assure that the stand pipe

remains in place when the engine is shut off
and not operating.

46
Front Port Plug

FRONT PORT PLUG • The front port plug is located towards the
front of the high-pressure oil rail.

• The rail was designed to be universal for

both sides of the engine. One side of the
high-pressure rail must be blocked off when
not being used with the stand pipe.

• NOTE: The front port plug is longer then

the rear supply port plug. If the front plug
is installed into the rear port opening,
damage to the stand pipe and branch
tube can result.

47
25
 FUEL MANAGEMENT SYSTEM
ICP Sensor Gasket

• The ICP sensor has a new gasket.

• The purpose of the ICP gasket is to seal the

valve cover to the high-pressure rail and
prevent the release of crankcase vapors or
splash oil.

• NOTE: It is important to apply a thin layer

of oil to both sides of the ICP sensor
gasket during installation to prevent ICP GASKET
damaging the gasket.

48
ICP Sensor/Valve Cover Assembly
ICP SENSOR
• The ICP sensor is installed over the gasket.

• The ICP sensor can be removed and

installed without the removal of the valve
cover.

• After torquing the ICP sensor to

specification, the valve cover gasket and
valve cover can be installed over the sensor.

ICP GASKET

49
High-Pressure Pump Cover

• The same high-pressure pump cover is

used.

• Since the ICP sensor has been relocated to

the right bank high-pressure rail, a brass
plug will replace the ICP sensor.

IPR VALVE
BRASS PLUG
50
26
 FUEL MANAGEMENT SYSTEM
IPR Heat Shield

• The IPR has a new removable heat shield

wrapped around it to help block excessive
heat from the exhaust.

• If the IPR has to be replaced the shielding

HEAT SHIELD SNAP will have to be removed from the old IPR
and installed on the new one.

• Simply unsnap the button and slide the

shield off.

51
High-Pressure Pump

• The high-pressure pump utilized with the

new wavy high-pressure rails will have the
capability to produce increased oil pressure
over the original high-pressure pump.

HIGH-PRESSURE
PUMP GEAR
52
DLC (Diamond Like Carbon) Coated
Plunger

• The injector plunger has had a DLC coating

applied to it.

• The coating will further increase the

robustness of the injector against poor fuel
BARREL quality/water intrusion and will reduce the
risk of internal scuffing.
PLUNGER

53
27
 NOTES

28
 ELECTRICAL COMPONENTS
Generation II Electrical Components
Electrical Components
• The PCM uses information from the sensors
to decide which commands to send to the
FICM, the actuators, and the glow plug
• Sensors system.

• Actuators • Modifications and additions have been made

to some electrical components.
• Glow Plug System
• PCM
• FICM

54
Sensor Overview
INTRUMENT CLUSTER

PCM RPM MPH

Powertrain Control Module

ICP MAF & IAT 1

BP
EOP
Switch
EP

MAP

EGRVP

AP

EGRTP

EOT CMP CKP ECT IAT 2

55

Sensor Overview

• The PCM sends a Vref of 5.0 volts to four engine • IAT1 is not used in any engine control. The IAT1 signal is used
mounted sensors: ICP, EP, EGRVP, and EGRTP. to assist in the operation of the air conditioning and engine
It also sends a 5.0 volt reference signal to four cooling fan.
chassis mounted sensors: MAF, BP, MAP, and AP.
• MAF is not used in any engine control. MAF is used in the EGR
• The PCM uses 5 volts in order to maintain monitor strategy to calculate the total clean air going into the
consistency throughout all operating conditions. engine. Once the total clean air is known, the amount of EGR
required can be calculated.
• The Vref is conditioned by the sensors then
returned to the PCM for use in determining the • NOTE: Failure in either or both of these components has no
fueling strategy and/or actuator duty cycle. effect on engine performance.

• The EGRTP (Exhaust Gas Recirculation

Throttle Position) Sensor is added.

29
 ELECTRICAL COMPONENTS

EGR Throttle Position

Powertrain Control Module
PCM

MIL

EGR Throttle Malfunction

and Sensor Indicator Lamp

56
EGRTP (Exhaust Gas Recirculation Throttle Position)
Sensor

• The EGR throttle position (EGRTP) sensor is a potentiometer that

provides a feedback signal to the PCM.

• The input signal is an analog voltage proportional to the rotary position

(angle) of the throttle plate located within the throttle body.

EGRTP SENSOR
57

30
 ELECTRICAL COMPONENTS
Actuators

Actuators • Actuators convert electrical output from the

PCM to hydraulic, mechanical, or electronic
work.

• Injection Pressure Regulator (IPR) • The 6.0L Power Stroke engine now uses
five (5) actuators: Injection Pressure
• Exhaust Gas Recirculation Valve (EGR) Regulator (IPR), Exhaust Gas Recirculation
(EGR) Valve, Variable Geometry
• Variable Geometry Turbocharger Control Turbocharger Control Valve (VGTCV), Glow
Valve (VGTCV) Plug Control Module (GPCM), and the
Exhaust Gas Recirculation Throttle Plate
• Glow Plug Control Module (GPCM) (EGRTP) Actuator.

• Exhaust Gas Recirculation Throttle Plate

(EGRTP)

58
EGRTP (Exhaust Gas Recirculation
Throttle Plate)

• The EGR throttle plate is designed to assist

with EGR operation.

• The EGRTP actuator modifies the intake

airflow from the charge air cooler into the
intake manifold.
EGR THROTTLE PLATE
• The EGRTP actuator regulates the rotary
motion of the throttle plate located within the
throttle body.

• The control of intake airflow provides

increased EGR system efficiency with the
throttle plate position determined by a signal
from the EGRTP sensor.

EGRTP ACTUATOR
59
Glow Plug Wiring Harness

• In order to increase the serviceability of the

glow plugs, the glow plug buss bar has been
replaced with a new glow plug harness. This
will provide flexibility in the harness, to ease
removal of glow plugs.

• In addition, the rocker-arm carrier has been

modified to improve accessibility to the glow
plug harness.

• NOTE: The glow plug buss bar and the

GLOW PLUG CONNECTORS glow plug wiring harness are not
interchangeable parts and should only be
replaced with the correct replacement
part.
60
31
 ELECTRICAL COMPONENTS
ICP Sensor

• The ICP sensor is no longer located in the

high-pressure pump cover.

• It has been relocated to the front on the right

high-pressure oil rail. ICP SENSOR

• The valve cover and GPCM bracket sets

over the ICP Sensor.

HIGH-PRESSURE
PUMP COVER
GPCM
61

32
 
ECONOLINE 6.0L DIESEL ENGINE

62

Econoline 6.0L 


POWER STROKE DIESEL
2004 6.0L Econoline Features

2004 6.0L Econoline Features • The 6.0L diesel engine will be a new
addition to the Econoline starting in 2004.

• The Econoline will feature a charge-air-

cooler for the first time.
• Remote Mount Oil Filter • The Econoline 6.0L diesel engine will
feature visual differences versus the
F-series.
• Charge Air Cooled • The Econoline 6.0L utilizes a remote mount
oil filter.

• Chassis Mounted FICM

63
33
 
E C O N O L I N E C O M P O N E N T L O C AT I O N
Horsepower and Torque
Horsepower and Torque

• The Econoline6.0L Power Stroke Engine
creates 235 HP at 3150 RPM and 440 ft/lb
of torque at 1600 RPM.

64
Left of Engine
1. EP (Exhaust Pressure) Sensor 1 2
2. GPCM (Glow Plug Control Module)

3. 12-way Connector

4. Battery Power Junction Point

3
65
Remote Mount Oil Filter
1. Upper Oil Pan

2. Oil Filter Cap

3. Oil to Filter Supply Line

4. Clean Oil to Engine Line

4 3

1
2
66
34
 
E C O N O L I N E C O M P O N E N T L O C AT I O N
2 Left Front of Engine
3
1. EP (Exhaust Pressure) Tube

1 2. Oil Level Gauge and Tube

3. 46-way PCM Connector

4. Upper Oil Pan

67

Left Rear of Engine

4
1. FICM Electrical Connectors

2. Oil Filter Housing

3. Remote Mount Oil Filter Oil Lines

4. Vehicle Battery Power Junction Point

1 2
68
35
 
E C O N O L I N E C O M P O N E N T L O C AT I O N
Right Front of Engine

3 2
1. Oil Fill Adapter 1

2. EGR Throttle Actuator

3. Heater Return

69
Right Rear of Engine
3
1. Glow Plug Harness 4
2. Block Heater

3. Secondary Fuel Filter Housing

4. Turbine Outlet

70
36
 
E C O N O L I N E L U B R I C AT I O N S Y S T E M
Lubrication System Features
Lubrication System Features
• The 2004 Econoline 6.0L utilizes the same
integrated oil cooler that is used in the
F-Series application.

• Do to space limitations, the canister style oil

• Integrated Oil Cooler filter must be remote mounted to the upper
oil pan on the driver side of the engine.

• Remote Mount Oil Filter

• Canister Style Oil Filter

71
Lubrication System Flow

REMOTE MOUNT OIL LINES

REMOTE MOUNT OIL

FILTER HEADER

OIL FILTER CANISTER 72

37
 
E C O N O L I N E L U B R I C AT I O N S Y S T E M
Remote Mount Oil Filter Header/
Fuel Filter Housing

• To accommodate the relocated oil filter, there

is a redesigned oil filter/fuel filter assembly FILTERED OIL
bolted to the oil cooler.

• This oil filter header has two access holes

for oil lines to transport oil to the oil filter TO OIL FILTER
housing at the left rear of the engine upper
oil pan.

TO ENGINE

UNFILTERED OIL
73
Oil Filter Bypass
OIL FILTER BYPASS VALVE
• The oil filter bypass is located at the bottom
of the remote mount oil filter header.

• If the oil filter becomes plugged or if the oil

line become restricted, the oil will pass
though this bypass to feed unfiltered lube oil
to the engine.

74
Remote Mount Oil Lines

• Since the space is limited on the Econoline UNFILTERED OIL

chassis, the oil filter housing has been
relocated to left rear corner of the engine’s
upper oil pan.

• Steel lines are used to route oil to the remote

mounted oil filter.

FILTERED OIL 75
38
 
E C O N O L I N E L U B R I C AT I O N S Y S T E M
Oil Line Routing: Engine Valley

• As the oil line leaves the oil filter header, it

drops down and passes under the
turbocharger mounting bracket.

• As the oil line reaches the rear of the engine

it rises over the high-pressure pump cover.

• The oil lines have been positioned toward

the center of the high-pressure pump cover
in order to avoid restricting access to the
IPR (Injection Pressure Regulator) valve.
UNFILTERED OIL
FROM OIL PUMP

FILTERED OIL FROM

OIL FILTER ASSEMBLY

76
Oil Line Routing: Rear

• The oil line is routed down the right rear of

UNFILTERED OIL the engine, staying clear of the IPR valve,
FROM OIL PUMP and under the right side exhaust up-pipe.

• The oil line enters the oil filter housing near

the outside edge of the housing. Clean oil
exits through the top, center of the oil filter
housing.

• The clean oil line returns to the oil filter

header, where the oil will be distributed to
the engine lube system and the high-
pressure oil reservoir.

FILTERED OIL
FROM OIL FILTER
• NOTE: The remote mount oil filter lines
must be removed in order to remove the
turbocharger mounting bracket.
OIL FILTER ASSEMBLY
77
39
 
ECONOLINE FUEL SYSTEM
Fuel Filter Housing
FUEL REGULATOR
• The fuel filter housing has been modified to
accommodate the Econoline chassis.
FUEL SUPPLY LINE
• The regulator has been repositioned to
provide accessibility in chassis.

• The fuel supply line now has a banjo bolt

with two copper washers connecting it to the
fuel filter housing.
BANJO BOLT

FUEL RETURN LINE

78
Engine Fuel System Flow

SECONDARY FUEL FILTER HOUSING

FUEL INLET CHECK VALVES

FUEL SUPPLY
FROM PUMP

FUEL RETURN TO TANK

79

40
 
ECONOLINE 6.0L DIESEL ENGINE
BATTERY POWER EP Sensor/GPCM
JUNCTION POINT
• The EP (exhaust pressure) sensor and tube
have been repositioned to adapt for the
GPCM chassis.

• The GPCM bracket has been relocated to

the left valve cover.

• The GPCM, EP sensor, and power junction

point all share a common stamped steel
mounting bracket. The mounting bracket is
also utilized to secure the compressor inlet
hose.
EP SENSOR

80
Oil Fill Adapter/Glow Plug
Connector/ICP Sensor
OIL FILL ADAPTER
• Oil fill tube adapter is now pointed to the
GLOW PLUG CONNECTOR front of the engine for accessibility.

• The glow plug harness has been lengthened

on the Econoline chassis to increase
accessibility to the harness connector.

• The location of the ICP sensor is the same

as on the F-Series.

ICP SENSOR

81
Engine Serial Number/Chassis
Mounted FICM
ENGINE SERIAL
NUMBER • The engine serial number is now located on
the external crankcase breather.

• The FICM has been relocated by the brake

booster on the Econoline chassis.

EXTERNAL CRANKCASE BREATHER

82
41
 NOTES

42
 
POWER STROKE DIESEL DIAGNOSTICS
Diagnostic Procedures and
Diagnostic Procedures and Service Tips

Service Tips • The information in this section is not

intended to replace any portion of the Ford
Motor Company Service Manual, but should
be used in conjunction.
• No Start Diagnostics
• Please see Ford Motor Company Service
• Fuel in Oil Manual for complete diagnostic and test
procedures.
• ICP Test
• CKP Trigger Wheel Test
• ICP Block-Off Tools
• Cylinder Balance
82

No Start Diagnostics
This procedure is a method to diagnose an engine crank, no start condition and to describe what is required for a 6.0L
diesel engine to start. With the WDS, access the DATALOGGER screen. Highlight PIDs listed below. Before cranking the
engine, hook up a mechanical fuel pressure gauge to the diagnostic port located on the secondary fuel filter housing.
Monitor fuel pressure and the highlighted PIDs to determine the cause of the no start concern.

• VPWR (battery power) - If low voltage condition is present, check

battery, charging system, or power/gnd circuits to the PCM.

• FICMLPWR (FICM logic power) - No/low voltage indicated could be Parameter Specification Measurement
caused by the 12-way connector or logic power fuse. Refer to Pinpoint S
for detailed 12-way conn. diagnostics. VPOWER 8 VOLT MIN.

• FICMVPWR - No or low voltage indicated could be caused by 12-way FICMLPOWER 8 VOLT MIN.
connector or the key power circuit. Voltage drop from the battery to the
FICM should not exceed a 2-5% difference.
FICMVPOWER 8 VOLT MIN.
• RPM - Low RPM can be caused by starting/charging system issues. No
RPM indicated while cranking could be CKP fault. RPM 100 RPM MIN.

• ICP - A minimum of 500 PSI (3.5 mPa) is required for the injectors to be ICP PRESSURE 500 PSI (3.5 mPa)
enabled. No or low oil in the hp system or reservoir, system leakage,
faulty IPR, or high-pressure pump could cause low pressure. ICP VOLTAGE .80 VOLTS MIN.

• IPR duty cycle - Typically will increase to 80-84% within a couple of FUEL PW 500 uS - 2mS
seconds of starting. Defaults to 14% (300 PSI) w/o CKP signal.
FICMSYNC YES/NO
• ICP V (ICP voltage) - Voltage reading below spec indicates low ICP
during crank.
SYNC YES/NO
• FUEL PW (fuel pulse width) - Pulse width defaults to 0 w/o CKP
signal, RPM below minimum spec, or low ICP. FUEL PRESSURE 45 psi MIN.

*NOTE: These specifications are minimum values. A

• FICMSYNC- No FICM sync could be caused by the PCM, FICM, or
minimum value may result in an extended crank time.
engine wiring harness.

• SYNC - No sync could be caused by CKP, CMP faults, PCM, or engine

wiring harness.

• NOTE: If the FICM has been replaced with a service part, it will need to be programmed. The service part does not
come programmed. The injectors will not rattle when the key is cycled until the FICM has been successfully
programmed.

43
 N O S TA R T D I A G N O S T I C S
Diagnosing FICM Logic Power:

• NOTE: If there is no FICM logic power to

the FICM, the injectors will still buzz once
the key is cycled but the engine will not
start. There will be no other symptoms
related to a no start condition.

• With the WDS, select DATALOGGER PID

FICMLPWR. This PID will show how much
voltage is being supplied to the FICM. If less
than eight volts check for short/open or
low battery.

• If no voltage is being supplied, check logic

power fuse located in the relay center box. FICM LOGIC FUSE
This box is mounted on the driver's side
towards the firewall.

• No voltage could also be caused by the FICM

83
logic circuit through the 12-way connector.

SYNC:

• SYNC is achieved when the PCM receives a signal from the Crankshaft sensor and Camshaft sensor indicating they are
working and in time. If the Crankshaft and Camshaft sensors are working improperly, the PCM cannot calculate engine
speed or cylinder position, preventing fuel delivery.

PCM
Powertrain Control Module

CKP

CMP

84

Diagnosing SYNC:

• No SYNC with an RPM signal typically is a faulty CMP sensor/circuit problem.

• No SYNC and no RPM signal, typically is a faulty CKP sensor/circuit problem.

44
 N O S TA R T D I A G N O S T I C S
FICM SYNC:

• The FICM uses CMPO (Camshaft Position Sensor Output) and CKPO (Crankshaft Position Sensor Output) signals, which
are sent by the PCM, to calculate FICM SYNC. FICM SYNC is calculated by the FICM and is the correlation between the
camshaft pin and the crankshaft triggers. Once FICM SYNC is achieved, the FICM uses engine speed, MFDES (Mass Fuel
Desired), EOT, and ICP to calculate fuel timing, pulse width, and pilot injection usage.

PCM
FICM Powertrain Control Module
Fuel Injection Contol
Module

CKPO

CMPO 85
Diagnosing FICM SYNC:

• If there is no FICM SYNC while cranking the engine, then the problem is limited to the circuit illustrated above. The FICM
SYNC circuit relays information from the PCM to the FICM.

• Engine Wiring Harness: FICM SYNC occurs through two circuits between the FICM and PCM. Verify engine wiring
harness circuits CMPO and CKPO. If one of these two circuits has a short/open, FICM SYNC will not occur.

• PCM: If the PCM is not working properly, FICM SYNC may not occur.

• FICM: If the FICM is not working properly, FICM SYNC may not occur.

Fuel Pressure: Air Inlet and Exhaust Restrictions:

• There must be an adequate amount of fuel flow and fuel • Be aware of air inlet or exhaust restrictions. If necessary,
pressure present before the engine will start. Areas listed eliminate these possibilities by removing the charge-air-
below can cause low fuel pressure/flow: cooler pipe/hose from the intake manifold inlet and the
- Faulty Fuel Pump exhaust down pipe from the turbine side of the turbo, for
- Pinched/Clogged Fuel Lines testing purpose only.
- Broken/Clogged Banjo Bolt
- Clogged Fuel Filter(s)
- Aerated Fuel
• Fuel quality should also be examined for a possible no
start condition.

AIR COOLER PIPE REMOVED

FROM INTAKE MANIFOLD

EXHAUST DOWN-PIPE REMOVED

FUEL PRESSURE ADAPTOR

86 87

45
 FUEL IN OIL DIANOSTIC PROCEDURE
DIESEL FUEL IN ENGINE OIL DIAGNOSTICS
ISSUE/CAUSE: Some vehicles equipped with the 6.0L diesel engine may exhibit diluted oil, runs rough and/or low
power. This may be caused by fuel leaking into the engine from the injectors.

• NOTE: THIS PROCEDURE MUST BE FOLLOWED COMPLETELY AND EXACTLY AS WRITTEN. FAILURE TO DO
SO MAY RESULT IN MIS-DIAGNOSIS, INCOMPLETE REPAIR OR UNNECESSARY PART REPLACEMENT.

• Before starting the engine, check engine oil level on dipstick. If the oil level is above 'max' due to dilution with diesel fuel,
the oil will appear thin and watery. Due to the design of the dipstick, it may be difficult to use for confirming an over full
condition. If an over full condition is suspected, insert a clean dipstick leaving it one inch above the seated position.
Remove the dipstick and check the oil level. Continue this process, leaving the dipstick one inch higher each time. If the
oil level is determined to be over full, pull the drain plug and let the oil/fuel drain out until it stops dripping (be sure to also
drain the oil filter housing). Measure the
amount of fluid drained from the crankcase.
RIGHT BANK FUEL LINE

• Note: For 6.0L Power Stroke diesel engines
with engine oil diluted with four or more
quarts of diesel fuel, the turbocharger LEFT BANK FUEL LINE
endplay needs to be checked (.001”- .004”
allowable). Also check radial shaft
movement by lifting the shaft up and BRASS ADAPTORS
rotating the shaft to check for compressor
or turbine wheel housing contact. If any
wheel contact is noticed, the turbocharger
must be replaced.

• Check the PCM for Cylinder

Contribution/Balance Diagnostic Trouble
Codes (DTC's). Diagnose Cylinder
Contribution/Balance DTC's per pinpoint test
P15. Cylinder Contribution/Balance DTC's will FUEL PRESSURE TEST PORT PLUG
not be set for all injector related concerns
resulting in fuel dilution. Continue with
88
remaining steps.

• Block the fuel line to the left head at the fuel filter housing. To do this, remove the fuel line from the connection point at the
secondary fuel filter housing. Remove the brass adaptor that is screwed into the filter housing. Remove the fuel pressure
test port plug from the front of the secondary fuel filter housing. Install the plug in the left bank outlet port. The fuel
pressure adaptor (#303-765) and fuel pressure gauge should be installed at the test port in order to confirm constant
pressure.

• Run the fuel pump using WDS 'Active Right Head Leak Test Set-Up
Commands' in order to maintain constant
pressure.

• Watch for fuel to drain out of the oil pan drain

hole. Depending on the severity of the leak, it LEFT BANK FUEL LINE
may take some time to leak enough fuel to run
down to the pan. Allow the fuel pump to run
for up to 10 minutes.It is possible that the leak FUEL PRESSURE ADAPTOR
indication may not occur when the engine is
cold (cool). If this is the case, it will be
necessary to perform the leak test on a warm
engine. The block heater may be used to
increase the coolant temperature to induce the
leak if necessary in the case where the engine
cannot be idled to warm-up prior to leak
evaluation.
TEST PORT PLUG
89

46
 FUEL IN OIL DIANOSTIC PROCEDURE
Left Head Leak Test Set-Up • If fuel is present suspect at least one injector
or injector o-ring leaking in the right head.
Turn off the fuel pump at this time.

• Reverse the test at this time, blocking the

RIGHT BANK FUEL LINE right bank fuel line at the fuel filter housing.
Use the same procedure as described in
step 3 (move the plug from the left supply
TEST PORT PLUG port to the right bank supply port). It may
also be necessary to loosen or remove the
fuel line-retaining bolt secured to the front of
the intake manifold.

• Run the fuel pump using WDS 'Active

Commands'.

• Watch for fuel to drain out of the oil pan

drain hole. Depending on the severity of the
FUEL PRESSURE ADAPTOR leak, it may take some time to leak enough
fuel to run down to the pan. Allow th efuel
90 pump to run for up to 10 minutes.

• If fuel is present suspect at least one injector or injector o-ring is leaking in the left head. Turn off the fuel pump at this time.
Reconnect the fuel line.

• Remove the appropriate valve cover/s. If a fuel leak was not identified on the right or left bank, remove both valve covers
for additional inspection.

• Remove the high-pressure oil rail. Check the torque of each injector hold down bolt. Refer to the Workshop Manual Section
303-04D for torque specifications. If an injector is found loose remove the injector. Inspect the injector body, injector body
o-rings, and copper washer (at injector tip) for damage. Replace as necessary.

CAUTION: Installation and removal of an injector should not be completed with air/power tools. Excessive speed
can damage the injector o-rings.

• Clean the top of the head with brake clean and dry it thoroughly especially on the down side of each injector.

• Turn on the fuel pump. Inspect injector body o-ring area. Look carefully to see if fuel is leaking from the small weep hole
just above the top injector body o-ring. Use a mirror to help look for fuel leaking from individual injectors. If a leak is not
detected within 5 minutes, install 1 oz. of oil dye and continue your inspections.

Note: Adding 1 oz. of oil dye to the fuel filter housing in conjunction with use of a black light may aid in identifying
the fuel leak.

• If fuel is observed leaking from the injector body o-ring area replace the two injector body o-rings. If fuel is leaking from the
small weep hole just above the top injector body o-ring replace the injector.

CAUTION: Installation and removal of an injector should not be completed with air/power tools. Excessive speed
can damage the injector o-rings.

• Following any repair, retest to confirm repair.

• Check the Charge Air Cooler (CAC) for fuel and/or oil. Clean the CAC and air dry with shop air thoroughly before
reinstalling.

• Re-install the oil pan drain plug. Refill engine with oil and change oil filter.

• Drive vehicle approximately 20 miles.

• Change engine oil and filter. Be sure to drain the oil out of the oil filter housing. Repeat final steps (maximum of two engine
oil flushes).

47
 HIGH-PRESSURE OIL DIAGNOSTICS
HIGH-PRESSURE OIL LEAK DIAGNOSTIC PROCEDURE

Symptoms:

• Driveability - Runs Rough, Stalls, No Start When Hot

• DTCs P2284, P2290 Or P2291

6.0L Diesel Engine - High-Pressure Oil System Diagnostics:

• Verify nature of concern.

• Verify lube oil supply pressure.

• If the nature of the concern exists hot only (hot no starts), safely bring the vehicle up to necessary temperature range.
Monitor IPR (Injection Pressure Regulator) duty cycle as EOT (engine oil temperature) increases. A high-pressure oil leak
should be indicated by a rising IPR duty cycle.
As EOT increases and the leak rate increases,
ICP pressure can begin to drop as the IPR is
no longer capable of compensating. AIR HOSE FITTING

• Check the operation of the IPR valve. Remove

one of the valve covers from the engine.
Apply shop-air pressure to the high-pressure
rail using special tool adapter #303-766. When
the air pressure is applied, there will be a
noticable air leak do to the IPR valve being in
an open state.

• With the WDS, increase the duty cycle of the

IPR valve. This should block that air leak. If
no change is heard, the IPR valve is not TOOL # 303-766
functioning as commanded. Your concern
could be the IPR valve or the PCM to IPR
circuit. If a change in the air leak is heard, the
IPR valve is operating and investigation for
the high-pressure oil leak begins.

• With the IPR blocking the air leak to the oil pan, 91
listen for the position of the air leak in the NOTE: Air may leak past the high-pressure oil pump shaft seal.
engine. A stethoscope can improve your ability This is normal and DOES NOT require pump replacement.
to narrow down the location of the leak.

The leak can exist in the following areas:

Early model:
• Cracked/broken check valve and fitting in high-pressure oil rail, under either valve cover(s).
• Disconnected high-pressure hose(s) under valve cover(s).
• Stand pipe from high-pressure hose to the branch tube in the tappet gallery (o-ring at the bottom could be cut/torn or
missing).

Wavy rail:
• O-rings on the top and bottom of each stand pipe and/or all four plugs in the high-pressure rail.

All Models:
• O-ring in between discharge tube and high-pressure pump.
• O-ring around discharge tube that fits inside high-pressure pump cover.
• High-pressure pump inlet o-ring.
• Branch tube from high-pressure pump to stand pipe in the tappet gallery.
• High-pressure oil injector o-ring (high-pressure rail connects to the injector).

48
 CRANKSHAFT TIMING WHEEL
BENT/DAMAGED CRANKSHAFT TRIGGER WHEEL
Symptoms:

• This procedure is intended to identify a bent/damage crankshaft trigger wheel. The most common symptom is a rough
idle.The EOT (Engine Oil Temperature) does not affect the rough idle concern.

Diagnostics:

• Assure there are no codes present. If there are any codes, repair as necessary before continuing with the following
procedure.

• Start engine and verify rough idle concern. Slightly accelerate engine off of idle, does the engine smooth out? If it does,
proceed with the following diagnostics.

• Using WDS (World Diagnostic System) monitor Power Balance. Typically there are two injectors indicating weak cylinders.
These two injectors will be 180 degrees off in firing order (firing order is 1,2,7,3,4,5,6,8). For example, #3 & #8 will indicate
weak cylinders.

• Perform a Mass Fuel Desire Test to verify these injectors are contributing correctly.

• If they indicate no problem found, select #1 INJ PID. With the solid border surrounding the PID, enable active command
control for injector cancel. Take control of the Active Command but DO NOT toggle "+/-" to disable/cancel the injector.

• Notice the idle quality while performing this function. If the engine smoothes out, this is a good indication of a bent trigger
wheel.

Verify:

TO VERIFY THE CRANKCHAFT TRIGGER WHEEL IS DAMAGED FOLLOW THE PROCEDURE BELOW.

• Disconnect battery cables.

• Drain oil out of oil pan.
• Remove both turbocharger cooler pipes.
• Remove the radiator stator shroud.
• Loosen engine mount bolts from chassis. Lift engine off of chassis until turbo is against the heat shield on the cowl.
• Remove all the oil pan bolts. Drop oil pan down to remove bolts in the pick up tube. Remove the oil pan by backing it out
towards the transmission.
• The crankshaft trigger wheel is located at the front of the crankshaft. Manually turn engine over while inspecting every
tooth on the trigger wheel.
• If there is any visual damage to the teeth (see example below) contact the Ford Technical Service Hotline for instructions.

DAMAGED TEETH

DAMAGED TOOTH

92 93

49
 ICP BLOCK-OFF TOOLS
Right Bank Block-Off with ICP
Sensor
• This block-off tool is used on the right bank
only.

• The ICP sensor break-out harness (Tool #

418-D003) is utilized to extend the reach of
the wiring harness so pressure/voltage can
be read using the WDS.

• This tool will enable you to eliminate the

right bank high-pressure rail and injectors
while testing the integrity of the remaining
high-pressure oil system. 94
• To utilize the tool properly, the ICP sensor is
removed from the high-pressure oil rail and
is placed in the block off tool.

BREAK-OUT HARNESS

95
Left Bank Block-Off Tool

• The solid block-off tool is used in the left

bank high-pressure oil rail only.

• It enables you to eliminate the left high-

pressure oil rail and the left bank injectors
while testing the integrity of the remaining
high-pressure oil system.

• ICP pressure is measured using the ICP

sensor installed in the right bank high-
pressure oil rail or the right bank block-off
tool. BLOCK OFF TOOL 96

• NOTE: Both block-off tools can be used

at the same time to eliminate both
high-pressure oil rails and all eight
injectors. ICP pressure/voltage will be
monitored using the ICP sensor installed
in the right bank block-off tool, the ICP
break-out harness (as pictured above),
and the WDS.
97
50
 CYLINDER BALANCE TEST
CYLINDER BALANCE TEST

Cylinder Balance Test:

• Before using Cylinder Balance Test, Performance Diagnostic routines should be followed to insure no other performance
concerns are present.

• Cylinder Balance Test measures the increase of engine RPM during each firing cycle. The test then compares the RPM
contribution of each individual cylinder to determine a weak cylinder.

When performing Cylinder Balance you should use the following procedure:

• Using WDS, connect to the vehicle and

perform a POWER BALANCE TEST. DATALOGGER
• With POWER BALANCE still running
switch to DATALOGGER and select an
injector PID (1-8, it doesn't matter which
one). Highlight the injector pid and take
active command of the pid. Do not shut
the injector off.
#1 INJECTOR STILL ON
• The FICM has a fuel correction feature
that is used to smooth idle operation by
adding fuel to any cylinder that lowers
engine speed during a firing
ACTIVE COMMAND
cycle.

• Following these steps will disable the

FICM's fuel correction feature. Taking
active command of an injector will cause
all eight injectors to use a base line
fuel rate.
98
• Using the tabs at the top of the screen
switch back to the POWER BALANCE
and look for any injector that falls below
15 RPM.

• If a cylinder drops below 15 RPM perform

an INJECTOR ELECTRICAL TEST and POWER BALANCE TEST
a RELATIVE COMPRESSION TEST to
check for base engine problems. If no
other problems are found replace the
injector for the indicated cylinder.

• Note: Active command will only

disable fuel correction for about 1 min.

99

51
 NOTES

52
 APPENDIX

TABLE OF CONTENTS
To r q u e C h a r ts . . . . . . . . . . . . . . . .54
H a r d Sta r t / N o Sta r t D i a g n o s t i c s . . .58
Performance Diagnostics . . . . . . . .59
Wiring Diagrams
F-Series(single alt.) . . . . . . . . . . . . . . . . . . . . .60
F-Series(dual alt.) . . . . . . . . . . . . . . . . . . . . . .62
Econoline(single alt.) . . . . . . . . . . . . . . . . . . . .64
Econoline(dual alt.) . . . . . . . . . . . . . . . . . . . . .66

Diagnostic Codes . . . . . . . . . . . . . .68

Glossary . . . . . . . . . . . . . . . . . . . .72
Index . . . . . . . . . . . . . . . . . . . . . . .75

53
 SPECIAL TORQUE CHART
COMPONENT STANDARD METRIC
Air inlet duct clamp ........................................................44 lbf/in 5 Nm
C a m s h a ft f o l l o w e r r e ta i n i n g d e v i c e b o l t . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0 l b f / ft 13 Nm
C a m s h a ft p o s i t i o n ( C M P ) s e n s o r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 l b f / i n 11 N m
C a m s h a ft t h r u s t p l a t e m o u n t i n g b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 l b f / ft 31 Nm
C o n n e c t i n g r o d b o l t ( I n i t i a l ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 l b f / ft 45 Nm
( F i n a l ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 0 l b f / ft 68 Nm
C o o l a n t ( b l o c k ) h e a t e r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 0 l b f / ft 41 Nm
Crankcase breather ........................................................62 lbf/in 7 Nm
C r a n k c a s e P l u g ( M 1 6 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 5 l b f / ft 20 Nm
C r a n k s h a ft p o s i t i o n ( C K P ) s e n s o r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 l b f / i n 11 N m
* C y l i n d e r h e a d b o l ts ( s e e f i g u r e A ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . f i g u r e A figure A
EGR cooler coolant supply port cover (on oil filter base)
(M6) ..........................................................89 lbf/in 10 Nm
E G R c o o l e r V- b a n d c l a m p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 8 l b f / i n 6 Nm
E G R c o o l e r f l a n g e ( s t u d s ) ( s e e n o t e 1 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0 l b f / ft 13 Nm
E G R c o o l e r s u p p o r t ( s e e n o t e 1 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 l b f / ft 31 Nm
E G R v a l v e m o u n t i n g b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0 l b f / ft 13 Nm
Engine coolant temperature sensor (ECT) ........................108 lbf/in 12 Nm
Engine oil pressure switch (EOP) ....................................108 lbf/in 12 Nm
E x h a u s t m a n i f o l d f l a n g e ( t o u p p i p e ) ( s e e n o t e 2 ) . . . . . . . . . . . . 2 0 l b f / ft 27 Nm
E x h a u s t m a n i f o l d ( s e e n o t e 2 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 8 l b f / ft 38 Nm
Exhaust pressure (EP) sensor bracket ............................106 lbf/in 12 Nm
Exhaust pressure (EP) sensor ..........................................108 lbf/in 12 Nm
E x h a u s t p r e s s u r e ( E P ) t u b e n u ts ( s e e n o t e 2 ) . . . . . . . . . . . . . . . . . . 11 l b f / ft 15 Nm
E x h a u s t u p p i p e c o u p l i n g o n r i g h t s i d e . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 0 l b f / ft 27 Nm
* F l y w h e e l b o l ts ( s e e f i g u r e B ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 9 l b f / ft 94 Nm
F r o n t c o v e r m o d u l e b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 l b f / ft 24 Nm
F u e l c h e c k v a l v e ( b a n j o b o l t ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 8 l b f / ft 38 Nm
F u e l f i l t e r s u p p l y a n d r e t u r n l i n e s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 l b f / ft 43 Nm
F u e l f i l t e r s u p p l y t o h e a d l i n e s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 9 l b f / ft 26 Nm
F u e l i n j e c t o r h o l d d o w n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 l b f / ft 33 Nm
F u e l r a i l p l u g ( r e a r o f h e a d ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 0 l b f / ft 27 Nm
F u e l S u p p l y L i n e B a n j o b o l t ( E c o n o l i n e o n l y ) . . . . . . . . . . . . . . . . . . 2 6 l b f / ft 35 Nm
Glow plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 l b f / ft 19 Nm
Glow plug control module (GPCM) ..................................71 lbf/in 8 Nm
H e a t s h i e l d f o r i n ta k e m a n i f o l d ( M 6 n u t ) . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 l b f / i n 11 N m
H e a t s h i e l d b o l ts f o r r e a r ( M 6 t h r e a d f o r m i n g ) . . . . . . . . . . . . . . . . . . 9 6 l b f / i n 11 N m
( M 1 0 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 6 l b f / ft 49 Nm
H i g h p r e s s u r e d i s c h a r g e t u b e m o u n t i n g b o l ts . . . . . . . . . . . . . . . . . . 7 1 l b f / i n 8 Nm
H i g h p r e s s u r e r a i l f r o n t p o r t p l u g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 0 l b f / ft 82 Nm
H i g h p r e s s u r e r a i l s u p p l y p o r t p l u g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 0 l b f / ft 82 Nm
H i g h p r e s s u r e o i l r a i l p l u g ( M 1 4 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 l b f / ft 45 Nm
(M8) ......................................96 lbf/in 11 N m
High pressure oil rail bolt (see figure C) ..........................120 lbf/in 14 Nm
H i g h p r e s s u r e p u m p c o v e r b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 l b f / i n 11 N m
H i g h p r e s s u r e p u m p c o v e r p l u g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 l b f / ft 35 Nm
H i g h p r e s s u r e p u m p d r i v e g e a r b o l t . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 l b f / ft 129 Nm
H i g h p r e s s u r e p u m p m o u n t i n g b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 l b f / ft 24 Nm
Injection control pressure (ICP) sensor ............................108 lbf/in 12 Nm
I n j e c t i o n p r e s s u r e r e g u l a t o r ( I P R ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7 l b f / ft 50 Nm
I n ta k e a i r t e m p e r a t u r e 2 ( I AT 2 ) s e n s o r . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 l b f / ft 18 Nm
I n ta k e m a n i f o l d ( s e e f i g u r e D ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 l b f / i n 11 N m
L i ft i n g e y e b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 0 l b f / ft 41 Nm
L o w e r c r a n k c a s e m a i n b o l ts ( s e e f i g u r e E ) . . . . . . . . . . . . . . . . . . . . . . f i g u r e A figure A
L o w e r c r a n k c a s e o u t e r b o l ts ( M 8 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 l b f / i n 24 Nm

54
 SPECIAL TORQUE CHART
COMPONENT STANDARD METRIC
O i l c o o l e r m o u n t i n g b o l ts ( M 8 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 l b f / ft 22 Nm
(M6) ........................................89 lbf/in 10 Nm
O i l f i l t e r c a p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 l b f / ft 24 Nm
O i l f i l t e r d r a i n ( E c o n o l i n e o n l y ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 8 l b f / ft 10 Nm
O i l f i l t e r h o u s i n g b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 l b f / ft 15 Nm
O i l f i l t e r s ta n d p i p e b o l t ( n e w ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 l b f / i n 6 Nm
( r e i n s ta l l a t i o n ) . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7 l b f / i n 3 Nm
O i l pa n d r a i n p l u g ( s e e n o t e 3 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 l b f / ft 25 Nm
O i l p i c k u p t u b e f l a n g e b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 l b f / ft 24 Nm
O i l p u m p h o u s i n g b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 l b f / i n 8 Nm
O i l p r e s s u r e r e g u l a t o r p l u g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 9 - 2 1 l b f / ft 26-29 Nm
P i s t o n c o o l i n g j e t ( s e e n o t e 4 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0 l b f / ft 13 Nm
R o c k e r a r m f u l c r u m b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 l b f / ft 31 Nm
Wa t e r p u m p b o l ts ( M 8 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 7 l b f / ft 23 Nm
Wa t e r p u m p p l u g s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 - 2 8 l b f / ft 35-38 Nm
Wa t e r p u m p p u l l e y b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 l b f / ft 31 Nm
T h e r m o s ta t h o u s i n g b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 7 l b f / ft 23 Nm
Tu r b o e x h a u s t a d a p t e r v - b a n d c l a m p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0 8 l b f / i n 12 Nm
Tu r b o o i l s u p p l y b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 l b f / ft 24 Nm
Tu r b o o i l s u p p l y l i n e , f l a n g e r e ta i n i n g b o l t . . . . . . . . . . . . . . . . . . . . . . 7 l b f / ft 10 Nm
Tu r b o t o m o u n t i n g b r a c k e t b o l ts ( s e e n o t e 2 ) . . . . . . . . . . . . . . . . . . 2 3 l b f / ft 31 Nm
Tu r b o b r a c k e t t o c r a n k c a s e m o u n t i n g b o l ts . . . . . . . . . . . . . . . . . . . . . . 2 3 l b f / ft 31 Nm
Va l v e c o v e r b o l ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 l b f / i n 9 Nm
* Vi b r a t i o n d a m p e r ( s e e n o t e 5 ) ( i n i t i a l ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 0 l b f / ft 68 Nm
( F i n a l ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . a d d i t i o n a l 9 0 d e g r e e s r o ta t i o n

* O n l y u s e n e w b o l ts . O n c e t h e s e b o l ts h a v e b e e n l o a d e d t o t h e i n i t i a l v a l u e , d o n o t r e u s e .

Torque Chart Notes

• 1) Tighten 2 M6 studs in front EGR cooler flange

first then install M8 EGR cooler support bolt.

• 2) Apply High Temperature Nickel Anti-Seize

S TA N D A R D TO R Q U E C H A R T Lubricant (F6AZ-9L494-AA) to threads of bolts
Hex Flange Head prior to assembly.
Thread To r q u e To r q u e Wr e n c h
Diameter l b f / ft Nm Size (mm) • 3) Lightly coat o-ring with engine oil before
M6 x 1 8 11 8 installing.
M8 x 1.25 18 24 10
M10 x 1.5 36 49 13
M12 x 1.75 61 83 15 • 4) Apply Threadlock 262 to bolt threads prior to
M16 x 2 154 208 21 assembly

Hex Head • 5) Tighten bolts across center of crankshaft.

M6 x 1 6 8 10
M8 x 1.25 15 20 13
M10 x 1.5 30 40 16
M12 x 1.75 51 69 18
M16 x 2 128 173 24

Pipe Thread
1/8” NPT 7 10.2
1/4” NPT 10 13.6
3/8” NPT 15 20.4
1/2” NPT 25 34.0
3/4” NPT 30 40.8 • All figures on next page.

55
 SPECIAL TORQUE CHART
Cylinder Head Bolts
Intake Side
15 13 11 12 14
• NOTE: Once bolts have been loaded to the
initial value, they may not be reused. Use
only new bolts.

• Step 1: Torque the M14 (1-10) cylinder head

9 5 1 3 7
bolts to 65 lbf/ft (88 Nm) in the numerical
sequence shown.

• Step 2: Torque the M14 cylinder head bolts

1, 3, 5, 7, & 9 to 85 lbf/ft (115 Nm) in the 10 6 2 4 8
numerical sequence shown.
Exhaust Side
• Step 3: Tighten the M14 cylinder head bolts Figure A
an additional 90o clockwise in the numerical
sequence shown.

• Step 4: Tighten the M14 cylinder head bolts an additional 90o clockwise in the numerical sequence shown.

• Step 5: Tighten the M14 cylinder head bolts an additional 90o clockwise in the numerical sequence shown.

• Step 6: Torque the M8 (11-15) cylinder head bolts to 18 lbf/ft (24 Nm) in the numerical sequence shown.

• Final Step: Torque the M8 cylinder head bolts to 23 lbf/ft (31 Nm) in the numerical sequence shown.

Flywheel Bolts

• NOTE: Once bolts have been loaded to the initial value, they may not be
reused. Use only new bolts. 1 2
7 5
• Step 1: Torque the bolts to 1-5 lbf/ft (1.4-7 Nm) in the numerical sequence shown
above. 9 10

6 8
• Final step: Torque the bolts to 69 lbf/ft (94 Nm) in the numerical sequence shown
3 4
above.

Figure B

Intake Manifold Bolts

5

7
3
1

• Step 1: Install bolts 1 through 8 finger tight.

4

8
2

• Step 2: Torque bolts 9 though 16 to 8 lbf/ft (11

Nm).

• Final step: Torque all bolts to 8 lbf/ft (11 Nm) in

the numerical sequence shown.
16

10
14

12

9
15

11
13

Figure D

56
 SPECIAL TORQUE CHART
Wavy High Pressure Oil Rail Installation
and Torque Procedure
3 • Step 1: Place the oil rail on top of the carrier so
that the four single ball tubes are engaging the
injector lead angle.

• Step 2: Insert 3 guide bolts-- two on the ends of

the straight side of the oil rail and one in the
middle of the wavy side of the oil rail. See figure
to the left.

1 2 • Step 3: After the 3 guide bolts are threaded in 6

or 7 turns, press the rail into the injectors.

• Step 4: Once the oil rail has completely engaged

4 1 5 the injectors, the oil rail mounting feet should be
flat against the carrier mounting surfaces. Now
insert the remaining 6 bolts.

• Step 5: Turn all 9 bolts until snug.

9 8
• Step 6: Torque all bolts to 120 in/lbs. starting with
the center bolt on the wavy side of the oil rail.
Follow sequence shown in Figure C.
7 3 2 6

Figure C

Front of Engine Main Bearing Bolts

20 19 17 18 • NOTE: Bolts must contain a light film of oil on

the bearing surface (under the head) and
threads prior to assembly.

• Step 1: Torque the bolts to 110 lbf/ft (149 Nm) in

12 11 9 10
the numerical sequence shown.

• Step 2: Torque the bolts to 130 lbf/ft (176 Nm) in

the numerical sequence shown.

4 3 1 2 • Final step: Torque the bolts to 170 lbf/ft (231 Nm)

in the numerical sequence shown.

6 5 7 8

14 13 15 16

Bottom View
Figure E

57
 H A R D S TA R T / N O S TA R T D I A G N O S T I C S
CUSTOMER NAME
-NOTE-
IF CONCERN IS FOUND, SERVICE AS
REQUIRED. IF THIS CORRECTS THE MODEL YEAR

tio ebs nal

F-Series/Excursion/Econoline Powerstroke 2004.25 CONDITION, IT IS NOT NECESSARY TO
6.0L Power Stroke Diesel Engine Diagnostic Guide COMPLETE THE REMAINDER OF THE CHASSIS STYLE
L
DIAGNOSTIC PROCEDURE.

Customer Concerns (Please list in this box)

DEALER NAME P& A 1863 CLAIM NUMBER DATE

ite
CODE

o
ENGINE SERIAL NUMBER ODOMETER
TYPE OF SERVICE

VEHICLE GVW TRANSMISSION AMBIENT TEMPERATURE

i
PERSONAL COMMERCIAL

y) ess
7. Perform KOEO On-Demand Self Test 11. Glow Plug System Operation
NOTE : A hard start/ No start concern with EOT
• Use scan tool. DTC's set during this est are current faults GPCM Oper ation
te .
Diagnosti c • atur
n Troubl )
Fuel Oil Co ca l Hoses Leaks 8. Retrieve
v Continuous Trouble Codes e
Method Check • Use the scan tool . on at ll iff o

f
ma W
Vi sual • DT C's re ev during this test are historical faults. • Usi ng a and KOEO DTC's.
oc Pro
2. Check Engine Oil Level Troubl e Codes •
If
ify
f .

n
• Check for contam inants (fuel, coolant). 9 . KOEO Injector Electrical Self Test (Click Test) • Usi ng the s CTM and EOT pids, verify
• Co Vi . • . Inject sp end. ug
• il level. • ors will will • e lt ("on"time)
Method Check 1-8. per ure and ti
Vi sual Injector Relay on time Spec. Measurement
Tr e 1 to 120 B +
ate n S S (

» ieved, go to appropriate PPT

T test.
Inf iet
• inle ducts. 10. Scan T Wait to Start Lam me om g/p "on" time
• Inspect tem. • Scan too bel 9. 5 lts.
t Glow Plug Resistance
• if r f er
e nder indicator has been illuminated • Select t fr the scan tool • the pin co e cov er
Check param cr ng ne. • ow u
Vi sual Par Measurement • ne har
r L cai PT

V PWR Glow Glow Pl ug Harness to

Cl FI CMLPWR 8 volt min. Plug to ound or
TE IN FUEL lamp has been FICMVPWR Number to 2 ohm s 0 s
or

t RPM 100 RPM #1

• After ve in he tank, drai n a minimum #3
e e. ICP 3. 5 mP a min. #5
• Cet recommended for #7
optimum start. ICP volts .80 V min. #2
Fo ni d’s

Method Check FUEL PW 500 uS - 2 mS #4

Vi sual FI #6
A- PWR - If low ltage
t conditi is esent, check battery, #8
charging syst , or power/gnd circuits to the PCM.
5. Electric Fuel Pump Pressure 140
• Verify
f t hat the fuel pump volt gnd. key on. B - FI CM LPWR - No/lo volt indicated could be caused
120
• e essure ne f er
e ng way or c use.
r

100
Refer nostics
Time (seconds)
st

e C - FI CM VP ould be caused 80
Te Fo

w 60
Measurement D- chargi
40
0-160 PSI 45 PSI min. system
mi PM indicated wh cranking could be
20
Gauge P
0
If pressure fails low go to nextt step to verify no restr iction - PSI (3 .5 a) r 0 20 40 6 0 100 120 140
n stem, EOT (˚F)
F)

• Measure
r restricti a p let. hi
e

Instrument Measurement • Add 5 gl pl on time when abov e

h

0- " Hg 6 PSI al. 7000 feet

vacuum F - ICP - spec indicates low ICP
Se

» If > 6" Hg restr iction, check lines between pump and fuel tank. duri c
c

» If er s. If s are OK, check fuel G - to w/o

/ CKP
re gulator If re and filter re place fuel pump. - CM SY No sy could be P faults.
» Refer to PC/ED section 4 for detailed test procedures.

Wh th ollo ng rt s :
Fu 12B d P ( ) ( 1 2 A650
e t a c ag s t ic sh y o e.

List Part Name, Number and Serial Number of parts replaced.

58
 PERFORMANCE DIAGNOSTICS
CUSTOMER NAME
-NOTE-
IF CONCERN IS FOUND, SERVICE AS
REQUIRED. IF THIS CORRECTS THE MODEL YEAR

tio ebs nal

F-Series/Excursion/Econoline Powerstroke 2004.25 CONDITION, IT IS NOT NECESSARY TO
6.0L Power Stroke Diesel Engine Diagnostic Guide COMPLETE THE REMAINDER OF THE CHASSIS STYLE
L
DIAGNOSTIC PROCEDURE.

Customer Concerns (Please list in this box)

DEALER NAME P& A 1863 CLAIM NUMBER DATE

ite
CODE

ma W sio
ENGINE SERIAL NUMBER ODOMETER
TYPE OF SERVICE

VEHICLE GVW TRANSMISSION AMBIENT TEMPERATURE

PERSONAL COMMERCIAL

8. EG 12a. Low P

s
• Ver ify
f t no leaks. • Per ne f.f • lo , ˚ ˚ F)
• l i • Use m St ate Control for EGR. • Monito P wi .

e
• Inspect MAP hose, intercooler hose, and m folds for leaks. • Monitor EGR position sensor PID and calculate trav el. Parameter Spec. @ 670 RPM Measurement
Fuel l Coolant Elect rica l Hoses Leaks Instrument Spec. cent Actual Percent IC P 4.5-5.5 M + .3M Pa
Check Scan tool -1.2 V) )

f
Vi sual Cl _______ Cl osed T
Take reading b i IC P

oc Pro Cl 90 % »
If engi ne RPM is unstable, disco
If RPM is still unstable, re
r (ICP will default).
and go to 12b.

n
• been illuminated. .52 V) _______ Open » If RPM sm sensor is at fault.

• D e ng. Open est

• Cet w 50 mmended for • Check at low idle, abov e 70˚C (158˚ F)

y)
optimum performance 90 % and 3.2 V _______ Tr av el • M scan tool.
Tr av el Measurement
Method Check » Repair issue causing out of sp e continuing. 30 % MAX
ate n S S (
Visual 9. Exhaust Restriction » If duty cycle is below MAX spec go to next step.
Inf iet
• Vi exhaust syst r damage » If ec, check for system leak with

3. l • M t scan t ne tem at e procedure in Hard Start/No Star

• fuel, coolant). ˚ minimu

• C er t • Ca er tubes/connections, turbocharger
• M t level. EP 244 kP se r signs of damage or leaks.
r L cai PT

Check MAX Pe .
Visual 10a. Electric Fuel Pump Pressure • M P th tool.
• Measure
r fuel pressure at engine filter
t housing test port. • Road Test
T - sel ect appropriate gear to obtai
t n desi red engi ne
or
4. KOEO Demand T est • Road Tes
T t- engine full oad condition speed and full load on engine climbing hill or loaded truck.
• U Measurement
• D th test are current faults. 0-1.1 Mpa 310- 379 kPa Parameter Measuremen
r t
ic (0-160 PSI ) (45-55 PSI) min. MG P
Codes
Fo ni d’s

Econoline
5. C's » If fuel pressure fails low, Go to step10b.
• Use the scan tool . » If pr essure is above spec, check fuel retur n lines for restr iction. » If test fails low, inspect turbo blades fo r damage .

• DT re ev ing is t are historical faults. If no restr iction is present, replace fuel pressure regulator valve. est
• M eT er
Tr ouble Codes • Measure
r restriction at fuel p let. p/ (170˚ F) ni m.
6. KOEO Injector Electrical Self-Test Instrument Spec. Measurement • Bl ft valve cov er.
r

• U 6" Hg MAX • M T with no load at 3, 000 RPM .

st

• arily lick, then individual Measurement

Te Fo

in 1 » If on, check lines between pump and fuel tank. 8" H² MAX
Injector » If er If s are OK, check fuel lic
Tr ouble Codes re . If re and filter re p. If mo t 8 ² l
» If self test codes are re triev ed, go to appropriate PPT. 10c. Fuel Aeration TTest 15. Oil Ae ration TTest
7. Intake Restriction • Install clear hose on fuel return li at fuel control module. • Run engine at 3000 RPM for 1 minute.
• o
ocedu re . • Take oil mp fr the O itch
t t idle.
• let stem • Run n fuel d be free of bubbles. •
e

at Check Method heck

h

Instrument Spec. Check Vi sual Vi sual

M lic / » If air is pr re for leaks.
Se

Filter Minder 2"-25" H²0 11. KO On De mand TTest » Excessive oil aeration can be caused by depleated oil additives,
c

• This will test t ICP, EGR and VGT performance. pick-up tube leak, front cover seal leak, or upper pan seal leak.
KOER Note: If pe orman
o ce concern still exists, refer to Enhanced Injecto r
DTC th .

Wh th ollo ng rt s :
Fu 12B d P ( ) ( 1 2 A650
e t a c ag s t ic sh y o e.

List Part Name, Number and Serial Number of parts replaced.

59
 F - S E R I E S ( S I N G L E A LT. )

E ngine Mounted C omponents

S E NS OR S
R egulator
S ens e
B+
E F C Module
CAM IC P E OT ECT IAT 2 EP E OP V P WR V B P WR
C R A NK P OS IT ION S witc h S peed
P OS IT ION I-S ens e S ens or

Fan RCS - NC
I F A C lutch
D
FS S C
F C -V
T P WR G ND
RCS - NO
A /C C lutc h A B
A lternator

4 3 2 1

To B attery A lternator 8 7 6 5

2 1 2 1 B C A 2 1 2 1 2 1 B C A P ower

E lec Fan
C trl
T P WR G ND
FS S
V B P WR
F C -V
VGTCH
EP
VR E F
S IG R T N
IAT 2
ECT
E OT
IC P
C MP +
C MP -
C MP /C K P S h.- P WR G ND
CKP +
CKP -
IP R
VGTC
E GR VC
E GR VP
E GR TP
E GR TPC1
A C T UAT OR S E GR TPC2
GPE
GPD

1 2 1 2 A B C D E

K E YP WR
X3 - P in 7
D MP R
F E D C B A X3 - P in 27
C F IC M Logic P wr
A B B X3 - P in 8
F IC M Main P wr
A X3 - P ins 4, 23
F IC M Main P wr
X3 - P ins 24, 25
F IC M P wr G nd
X3 - P ins 1, 2, 3
F IC M P wr G nd
X3 - P ins 22, 26
C ylinder #2 C ylinder #4 C ylinder #6 C ylinder #8 CKPO F IC MM
X3 - P in 9
E GR TP C MP O C AN2H
X3 - P in 30
E GR E GR IDMC ANH C AN2L
IP R T hrottle X3 - P in 31
VGT A c tuator/ IDMC ANL
A c tuator A c tuator E GR VP A c tuator X3 - P in 32
IDMC ANS CKPO
X3 - P in 29
3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 X3 - P in 28 C MP O
X2 - P in 3
X2 - P in 23
X2 - P in 7
X2 - P in 24
X1 - P in 4
X1 - P in 21
X1 - P in 7
(Orientation = L ooking into
X1 - P in 22
terminals on c onnec tor) X1 - P in 1
P UR P LE = V inj (48 V OLT S ) X1 - P in 23
X1 - P in 6
Lt. B LUE = V ref (5 V OLT S )
X1 - P in 24
G R E E N = S IG NAL C IR C UIT X2 - P in 2
X2 - P in 17
Dk B lue = Data C ommunication Link
X2 - P in 6
B L AC K = G R OUND C IR C UIT X2 - P in 18
R E D = 12 V OLT S (V B att) F UE L INJE C T OR S
X1 - P in 2

** G old P lated P ins X1 - P in 19

X1 - P in 5
X1 - P in 20
X2 - P in 4
X2 - P in 19
X2 - P in 8
X2 - P in 20
3

X2 - P in 1
9 1 6
8 2 7

X2 - P in 21
C ontrolModule

X2 - P in 5
G low P lug

X2 - P in 22
X1 - P in 3
X1 - P in 17
2 1 4 3 2 1 4 3 2 1 4 3 2 1
4 X1 - P in 8
3
X1 - P in 18
3

X3 - P in 5
9 1 6

X3 - P in 10
8 2 7

C ylinder #3 C ylinder #5 C ylinder #7

C ylinder #1 Injec tor P inout
S iemens
1 - Open C oil P ower F IC M
2 - Open C oil G round Module
D 3 - C los e C oil P ower
C 4 - C los e C oil G round
B
A
NOT E : F or clarity of the print all three F IC M
connectors are s hown together as one.
T he pin numbers are color coded, blue
for X1, red for X2, and black for X3

60
 F - S E R I E S ( S I N G L E A LT. )

12 Way On/Off E ngine C onnec tor

5
N/C
4
A/C C lutch (-) N/C
7 Type 4

A/C C lutch (+) G round

2
3 F IC M P ower A/C R elay P C M P ower
V P ower R elay F P R elay
10 R elay
F IC M G round V P WR K E YP WR V P WR Fuel Pump
1
Type 4 B+
G round
F IC M Main P wr B+ B+ B+
12 B+
F IC MLogic P wr 10 Amp
50 Amp
MP R
6 M
8
K ey P ower K E YP WR
9 Inertia
Type 4
E OP S witch G round
S witch
11 DFCM Mod
8 Way On/Off
I-S ens e E ngine C onnec tor
6
7
8
3
Vehic le Mounted C omponents
Type 2
G round
2
G E N2C
5 B AP
G E N1C
4 MA P
INT R UME NT C L US T E R MA F /IAT 1
1 N/C
Diagnos tic s C onnec tor K E YP WR
AHC
N/C 5 J1- C 1 P oc ket
G E N1C P C M122 C has s is
1
G E N2C C onnec tor (46
4 1 8 R PM MP H
T P WR G ND
FS S
V B P WR
22
6
46
Way)

34, 46
40
** V P WR
K AP WR B +
9
CAN
L
16

B+ A B C D E F
** 2 1
APCM EPATS
F C -V P WR G ND CANH
14 11, 23 Module Module
VGTCH FPM
11 19 3
EP AC C R
27 2
VR E F FPC
36 5
S IG R T N B US +
25

P WR G ND
32

VP WR
IAT 2 B US -
45 44
ECT FE PS
32 39
E OT S C IL
44 9
IC P AC P S W A
29 16
C MP + S IG R T N
31 33
C MP - VR E F
43 45
C MP /C K P S h.- P WR G ND 42 MAF
42
CKP + 30 MAF R T N
21
CKP - IAT 1
41 43
IP R B AR O
2 38
VGTC MAP
10 41
E GR VC PBPP
23 17 Type 2
E GR VP G E NIL G round
33 30
E GR TP AP P 2
38 37
E GR TPC1 VR E F2
E GR TPC2
GPE
12
24
3
29
20
25
S IG R T N2
AP P 3
5 1
**
GPD AP P 1
17 26
F IC MM AC C S C D
28 8
C AN2H T OWS (Auto) To AC S ys tem 10 6
37 36 V P WR Starter Relay
C AN2L C P P (Man) C P S W - NC
26 36 V P WR CTRL Ignition Switch
CKPO BPS V P WR
19 28 START
C MP O BPP NC
20 18 B+ Type 2
B+
T R O_P N NO G round
T HR E E
J1- C 2 P oc ket 4 TR AC K
WF S
P C M122 E ngine 15 P E DA L
C onnec tor (46 DOL DF C M
3 Tripminder Module Horn Relay
Way)
** 22
1
7
VS O
CTO
TPO
After Market
Circuits ABS Module
INTRUMENT
CLUSTER
R
P
M
P
Water In Fuel Probe

M To Horn
CTRL
B+
B+
PTO P131/U137 Only M H
12
VS S Pressure Ctrl
35 Starter Motor Solenoid #1
C AN1H
13 C R UIS E C ONT R OL
C AN1L Public CAN
14 Pressure Ctrl
E BS Data Bus ON
27 N/C Solenoid #2
SCCS R E S UME S E T /AC C C OAS T
31 Horn Switch
S CC S R TN OF F 2200 680
120

24 Ohms Ohms
Ohms Pressure Ctrl
V is teon C S E G ND Type 6 Solenoid #3
10 G round
P C M122
TS PC 24 Way Pressure Ctrl
7 7
12A 650-??? Trans mis s ion 5R110 Transmission Wiring Assembly Solenoid #4
20 C onnec tor
Module
24
PCA Pressure Ctrl
9 12
PCB Solenoid #5
10 3
PCC
11 5 Converter
PCD
12 4 Clutch Ctrl
PCE Solenoid
13 1
PCF
14 8
PCG Line Pressure
2 10 Solenoid
PSA
17 N/C 14
PSB B ac k UP L amp
18 N/C 16
PSC TR S T S S /IS S OS S R elay C ontrol
19 N/C 9 V P WR
PSD
20 N/C 11
PSE B+
21 N/C 13
TFT
26 18
T S IG R T N
30 22
V B P WR LH B K P R H BKP
1 21 Lamp Lamp
T R -P
25 15
T P WR G ND
22 17
TS S
29 Type 4
IS S G round
27
OS S
28

R LC
3
T R O_N
4 G E M 4x4 Module

T OWIL N/C
5
G LS
24 N/C
G LIL
6 N/C

J1- C 3 P oc ket

** P C M122 Trans
C onnec tor (30 Way)

61
 F - S E R I E S ( D U A L A LT. )

E ngine Mounted C omponents

S E NS OR S
R egulator
S ens e
B+
E F C Module
CAM IC P E OT ECT IAT 2 EP E OP V P WR V B P WR
C R A NK P OS IT ION S witc h S peed
P OS IT ION I-S ens e S ens or

Fan RCS - NC
I F A C lutch
D
FS S C
F C -V
T P WR G ND
RCS - NO
A /C C lutc h A B
A lternator

4 3 2 1

To B attery A lternator 8 7 6 5

2 1 2 1 B C A 2 1 2 1 2 1 B C A P ower

E lec Fan
C trl
T P WR G ND
FS S
V B P WR
F C -V
VGTCH
EP
VR E F
S IG R T N
IAT 2
ECT
E OT
IC P
C MP +
C MP -
C MP /C K P S h.- P WR G ND
CKP +
CKP -
IP R
VGTC
E GR VC
E GR VP
E GR TP
E GR TPC1
A C T UAT OR S E GR TPC2
GPE
GPD

1 2 1 2 A B C D E

K E YP WR
X3 - P in 7
D MP R
F E D C B A X3 - P in 27
C F IC M Logic P wr
A B B X3 - P in 8
F IC M Main P wr
A X3 - P ins 4, 23
F IC M Main P wr
X3 - P ins 24, 25
F IC M P wr G nd
X3 - P ins 1, 2, 3
F IC M P wr G nd
X3 - P ins 22, 26
C ylinder #2 C ylinder #4 C ylinder #6 C ylinder #8 CKPO F IC MM
X3 - P in 9
E GR TP C MP O C AN2H
X3 - P in 30
E GR E GR IDMC ANH C AN2L
IP R T hrottle X3 - P in 31
VGT A c tuator/ IDMC ANL
A c tuator A c tuator E GR VP A c tuator X3 - P in 32
IDMC ANS CKPO
X3 - P in 29
3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 X3 - P in 28 C MP O
X2 - P in 3
X2 - P in 23
X2 - P in 7
X2 - P in 24
X1 - P in 4
X1 - P in 21
X1 - P in 7
(Orientation = L ooking into
X1 - P in 22
terminals on c onnec tor) X1 - P in 1
P UR P LE = V inj (48 V OLT S ) X1 - P in 23
X1 - P in 6
Lt. B LUE = V ref (5 V OLT S )
X1 - P in 24
G R E E N = S IG NAL C IR C UIT X2 - P in 2
X2 - P in 17
Dk B lue = Data C ommunication Link
X2 - P in 6
B L AC K = G R OUND C IR C UIT X2 - P in 18
R E D = 12 V OLT S (V B att) F UE L INJE C T OR S
X1 - P in 2

** G old P lated P ins X1 - P in 19

X1 - P in 5
X1 - P in 20
X2 - P in 4
X2 - P in 19
X2 - P in 8
X2 - P in 20
3

X2 - P in 1
9 1 6
8 2 7

X2 - P in 21
C ontrolModule

X2 - P in 5
G low P lug

X2 - P in 22
X1 - P in 3
X1 - P in 17
2 1 4 3 2 1 4 3 2 1 4 3 2 1
4 X1 - P in 8
3
X1 - P in 18
3

X3 - P in 5
9 1 6

X3 - P in 10
8 2 7

C ylinder #3 C ylinder #5 C ylinder #7

C ylinder #1 Injec tor P inout
S iemens
1 - Open C oil P ower F IC M
2 - Open C oil G round Module
D 3 - C los e C oil P ower
C 4 - C los e C oil G round
B
A
NOT E : F or clarity of the print all three F IC M
connectors are s hown together as one.
T he pin numbers are color coded, blue
for X1, red for X2, and black for X3

62
 F - S E R I E S ( D U A L A LT. )

12 Way On/Off E ngine C onnec tor

5
N/C
4
A/C C lutch (-) N/C
7 Type 4

A/C C lutch (+) G round

2
3 F IC M P ower A/C R elay P C M P ower
V P ower R elay F P R elay
10 R elay
F IC M G round V P WR K E YP WR V P WR Fuel Pump
1
Type 4 B+
G round
F IC M Main P wr B+ B+ B+
12 B+
F IC MLogic P wr 10 Amp
50 Amp
MP R
6 M
8
K ey P ower K E YP WR
9 Inertia
Type 4
E OP S witch G round
S witch
11 DFCM Mod
8 Way On/Off
I-S ens e E ngine C onnec tor
6
7
8
3
Vehic le Mounted C omponents
Type 2
G round
2
G E N2C
5 B AP
G E N1C
4 MA P
INT R UME NT C L US T E R MA F /IAT 1
1 N/C R egulator
Diagnos tic s C onnec tor K E YP WR S ens e
AHC
N/C 5 J1- C 1 P oc ket
G E N1C B+
1 P C M122 C has s is
G E N2C C onnec tor (46
4 1 8 R PM MP H
T P WR G ND
FS S
V B P WR
22
6
46
Way)

34, 46
40
** V P WR
K AP WR B +
9
CAN
L
16

B+
I-S ens e

A B C D E F
** 2 1
APCM EPATS
F C -V P WR G ND CANH
14 11, 23 Module Module A F I
VGTCH FPM
11 19 3
EP AC C R A lternator
27 2
VR E F FPC
36 5
S IG R T N B US +
25

P WR G ND
32

VP WR
IAT 2 B US -
45 44
ECT FE PS
32 39
E OT S C IL
44 9
IC P AC P S W A
29 16
C MP + S IG R T N
31 33
C MP - VR E F
43 45
C MP /C K P S h.- P WR G ND 42 MAF
42
CKP + 30 MAF R T N
21
CKP - IAT 1
41 43
IP R B AR O
2 38
VGTC MAP
10 41
E GR VC PBPP
23 17 Type 2
E GR VP G E NIL G round
33 30
E GR TP AP P 2
38 37
E GR TPC1 VR E F2
E GR TPC2
GPE
12
24
3
29
20
25
S IG R T N2
AP P 3
5 1
**
GPD AP P 1
17 26
F IC MM AC C S C D
28 8
C AN2H To AC S ys tem 10 6
37 T OWS (Auto) V P WR
36 C P S W - NC Starter Relay
C AN2L C P P (Man) V P WR
26 36 CTRL Ignition Switch
CKPO BPS V P WR
19 28 START
C MP O BPP NC
20 18 B+ Type 2
B+
T R O_P N NO G round
T HR E E
J1- C 2 P oc ket 4 TR AC K
WF S
P C M122 E ngine 15 P E DA L
C onnec tor (46 DOL DF C M
3 Tripminder Module Horn Relay
Way)
** 22
1
7
VS O
CTO
TPO
After Market
Circuits ABS Module
INTRUMENT
CLUSTER
R
P
M
P
Water In Fuel Probe

M To Horn
CTRL
B+
B+
PTO P131/U137 Only M H
12
VS S Pressure Ctrl
35 Starter Motor Solenoid #1
C AN1H
13 C R UIS E C ONT R OL
C AN1L Public CAN
14 Pressure Ctrl
E BS Data Bus ON
27 N/C Solenoid #2
SCCS R E S UME S E T /AC C C OAS T
31 Horn Switch
S CC S R TN OF F 2200 680
120

24 Ohms Ohms
Ohms Pressure Ctrl
V is teon C S E G ND Type 6 Solenoid #3
10 G round
P C M122
TS PC 24 Way Pressure Ctrl
7 7
12A 650-??? Trans mis s ion 5R110 Transmission Wiring Assembly Solenoid #4
20 C onnec tor
Module
24
PCA Pressure Ctrl
9 12
PCB Solenoid #5
10 3
PCC
11 5 Converter
PCD
12 4 Clutch Ctrl
PCE Solenoid
13 1
PCF
14 8
PCG Line Pressure
2 10 Solenoid
PSA
17 N/C 14
PSB B ac k UP L amp
18 N/C 16
PSC TR S T S S /IS S OS S R elay C ontrol
19 N/C 9 V P WR
PSD
20 N/C 11
PSE B+
21 N/C 13
TFT
26 18
T S IG R T N
30 22
V B P WR LH B K P R H BKP
1 21 Lamp Lamp
T R -P
25 15
T P WR G ND
22 17
TS S
29 Type 4
IS S G round
27
OS S
28

R LC
3
T R O_N
4 G E M 4x4 Module

T OWIL N/C
5
G LS
24 N/C
G LIL
6 N/C

J1- C 3 P oc ket

** P C M122 Trans
C onnec tor (30 Way)

63
 
E C O N O L I N E ( S I N G L E A LT. )

E ngine Mounted C omponents

S E NS OR S
R egulator
S ens e
B+
E F C Module
CAM IC P E OT ECT IAT 2 EP E OP V P WR V B P WR
C R A NK P OS IT ION S witc h S peed
P OS IT ION I-S ens e S ens or

Fan
I F A C lutch FS S

F C -V
T P WR G ND

A /C C lutc h A lternator

4 3 2 1

To B attery A lternator 8 7 6 5

2 1 2 1 B C A 2 1 2 1 2 1 B C A P ower

E lec Fan
C trl
T P WR G ND
FS S
V B P WR
F C -V
VGTCH
EP
VR E F
S IG R T N
IAT 2
ECT
E OT
IC P
C MP +
C MP -
P WR G ND
CKP +
CKP -
IP R
VGTC
E GR VC
E GR VP
E GR TP
E GR TPC1
A C T UAT OR S E GR TPC2
GPE
GPD

1 2 1 2 A B C D E

K E YP WR
X3 - P in 7
D MP R
F E D C B A X3 - P in 27
C F IC M Logic P wr
A B B X3 - P in 8
F IC M Main P wr
A X3 - P ins 4, 23
F IC M Main P wr
X3 - P ins 24, 25
F IC M P wr G nd
F IC M P wr G nd X3 - P ins 1, 2, 3
X3 - P ins 22, 26 F IC MM
C ylinder #2 C ylinder #4 C ylinder #6 C ylinder #8 CKPO
X3 - P in 9
E GR TP C MP O C AN2H
X3 - P in 30
E GR E GR IDMC ANH C AN2L
IP R T hrottle X3 - P in 31
VGT A c tuator/ IDMC ANL
A c tuator A c tuator E GR VP A c tuator X3 - P in 32
IDMC ANS CKPO
X3 - P in 29
3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 X3 - P in 28 C MP O
X2 - P in 3
X2 - P in 23
X2 - P in 7
X2 - P in 24
X1 - P in 4
(Orientation = L ooking into X1 - P in 21

terminals on c onnec tor) X1 - P in 7

X1 - P in 22
P UR P LE = V inj (48 V OLT S ) X1 - P in 1
X1 - P in 23
Lt. B LUE = V ref (5 V OLT S ) X1 - P in 6
X1 - P in 24
G R E E N = S IG NAL C IR C UIT X2 - P in 2
X2 - P in 17
Dk B lue = Data C ommunication Link X2 - P in 6
B L AC K = G R OUND C IR C UIT X2 - P in 18
F UE L INJE C T OR S
R E D = 12 V OLT S (V B att) X1 - P in 2
X1 - P in 19

** G old P lated P ins X1 - P in 5

X1 - P in 20
X2 - P in 4
X2 - P in 19
X2 - P in 8
X2 - P in 20
3

X2 - P in 1
9 1 6
8 2 7

X2 - P in 21
C ontrolModu e

X2 - P in 5
G low P lug

X2 - P in 22
X1 - P in 3
X1 - P in 17
2 1 4 3 2 1 4 3 2 1 4 3 2 1
4 X1 - P in 8
3
X1 - P in 18
3

X3 - P in 5
9 1 6

X3 - P in 10
8 2 7

C ylinder #3 C ylinder #5 C ylinder #7

C ylinder #1 Injec tor P inout
S iemens
1 - Open C oil P ower F IC M
2 - Open C oil G round Module
D 3 - C los e C oil P ower
C 4 - C los e C oil G round
B
A
NOT E : F or clarity of the print all three F IC M
connectors are s hown together as one.
T he pin numbers are color coded, blue
for X1, red for X2, and black for X3

64
 
E C O N O L I N E ( S I N G L E A LT. )

12 Way On/Off E ngine /Trans C onnec tor

T C IL V P WR
5
R LC
3
A/C C lutch (-) Type 4
7 G round
A/C C lutch (+)
2 PCM
4 F IC M P ower P ower
A/C R elay F P R elay B ack UP Lamp
V P ower R elay R elay
10 K E YP WR R elay C ontrol
F IC M G round V P WR VPW Fuel Pump
1
Type 4 B+ V P WR
G round R
F IC M Main P wr B+ B+ B+ B+
12 B+
F IC M Logic P wr 10 Amp
50 Amp
MP R
6 M
8
K ey P ower K E YP WR
9 Inertia
Type 4
E OP S witch G round S witch
11
8 Way On/Off DFCM Mod
I-S ens e E ngine C onnec tor LH B K P R H BKP
6 Lamp Lamp
7
8
3

G E N2C
2 Vehic le Mounted C omponents
5 B AP
G E N1C INS T R UME NT
4 MA P
C L US T E R MA F /IAT 1
1
Diagnos tic s C onnec tor K E YP WR
J1- C 1 P oc ket
G E N1C 1 P C M122 C has s is
G E N2C 4 C onnec tor (46 1 8 R PM MP H
T P WR G ND
FS S
V B P WR 46
22
6
Way)

34, 46
** V P WR
K AP WR B +
9 16

B+
Powertrain CAN
Data Bus A B C D E **
F 2 1
40 APCM
F C -V P WR G ND CAN1H
14 11, 23 CAN1L Module
VGTC H 11 FPM
19 3
EP 27 AC C R
2
VR E F 36 FPC
5
S IG R T N B US (+)
25

P WR G ND
32

V P WR
IAT 2 45 B US (-)
44
ECT 32 FE PS
39
E OT 44 S C IL
9
IC P AC P S W
29 16 Type 2

S IG R T N RCS - NO G round
C MP + 31 33
C MP - 43 VR E F
45
P WR G ND 42 MAF
42
CKP + 30 MAF R T N
21
CKP - 41 IAT 1
43
IP R 2 B AR O
38
VGTC MAP
10 41
E GR VC PBPP
23 17 Type 2

E GR VP G E NIL G round
33 30
E GR TP AP P 1
38 26
E GR TPC1 S IG R T N2
12 20 1
E GR TPC2
GPE
GPD
24

17
3
25
29
37
AP P 3
VR E F2
AP P 2
4
**
F IC MM AC C S RCS - NC
28 8
C AN2H T C S (Auto) 8 5
37 36 V P WR To AC
C AN2L S ys tem Starter Relay
26 C P S W - NC CTRL Ignition Switch
CKPO BPS
19 28 V P WR START
C MP O BPP NC
20 18 B+ Type 2 B+
T R O_P N NO G round
T HR E E
** J1- C 2 P oc ket 4 TR ACK
WF S DF C M
P C M122 E ngine 15 P E DA L
DOL Water In Fuel Probe
C onnec tor (46 3 Tripminder Module Horn Relay

**
Way) VS O CTRL
22
CTO B+
1 To Horn
TPO After Market B+
7
Circuits
12
PTO M
VS S N/C Powertrain CAN Pressure Ctrl
35 Solenoid #1
C AN1H Data Bus
V is teon 13 C R UIS E C ONT R OL Starter Motor
C AN1L
P C M122 14 Pressure Ctrl
E BS ON
27 N/C Solenoid #2
SCCS R E S UME S E T /AC C C OAS T
31 Horn Switch
12A 650-??? S CC S R TN OF F 2200 680
120

24 Ohms Ohms Ohms Pressure Ctrl

Module C S E G ND Type 6 Solenoid #3
10 G round

24 Way
TS PC 1 Trans mis s ion Pressure Ctrl
7 7
R LC C onnec tor 5R110 Transmission Wiring Assembly Solenoid #4
3 Dual 16 Way On/Off 20
T C IL Trans C onnec tor
5 24
PCA 2 Pressure Ctrl
9 12
PCB Solenoid #5
10 3 3
PCC 4
11 5 Converter
PCD 5
12 4 Clutch Ctrl
PCE 6 Solenoid
13 1
PCF 7
14 8
PCG Line Pressure
2 8 10 Solenoid
PSA 9
17 N/C 14
PSB 10
18 N/C 16
PSC 11 TR S T S S /IS S OS S
19 N/C 9
PSD 12
20 N/C 11
13
PSE
21 N/C 1 18
26 TFT 2 22
T S IG R T N
30 4 21
V B P WR
1 6 15
25 T R -P 3 17
22 T P WR G ND 5
TS S
29 8
IS S
27 7
OS S
28 9
T R O_N
4 N/C 10
Nav-Int
Wiring
AFL Wiring
5
3

J1- C 3 P oc ket

** P C M122 Trans
C onnec tor (30 Way)

65
 
E C O N O L I N E ( D U A L A LT. )

E ngine Mounted C omponents

S E NS OR S
R egulator
S ens e
B+
E F C Module
CAM IC P E OT ECT IAT 2 EP E OP V P WR V B P WR
C R A NK P OS IT ION S witc h S peed
P OS IT ION I-S ens e S ens or

Fan
I F A C lutch FS S

F C -V
T P WR G ND

A /C C lutc h A lternator

4 3 2 1

To B attery A lternator 8 7 6 5

2 1 2 1 B C A 2 1 2 1 2 1 B C A P ower

E lec Fan
C trl
T P WR G ND
FS S
V B P WR
F C -V
VGTCH
EP
VR E F
S IG R T N
IAT 2
ECT
E OT
IC P
C MP +
C MP -
P WR G ND
CKP +
CKP -
IP R
VGTC
E GR VC
E GR VP
E GR TP
E GR TPC1
A C T UAT OR S E GR TPC2
GPE
GPD

1 2 1 2 A B C D E

K E YP WR
X3 - P in 7
D MP R
F E D C B A X3 - P in 27
C F IC M Logic P wr
A B B X3 - P in 8
F IC M Main P wr
A X3 - P ins 4, 23
F IC M Main P wr
X3 - P ins 24, 25
F IC M P wr G nd
F IC M P wr G nd X3 - P ins 1, 2, 3
X3 - P ins 22, 26 F IC MM
C ylinder #2 C ylinder #4 C ylinder #6 C ylinder #8 CKPO
X3 - P in 9
E GR TP C MP O C AN2H
X3 - P in 30
E GR E GR IDMC ANH C AN2L
IP R T hrottle X3 - P in 31
VGT A c tuator/ IDMC ANL
A c tuator A c tuator E GR VP A c tuator X3 - P in 32
IDMC ANS CKPO
X3 - P in 29
3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 X3 - P in 28 C MP O
X2 - P in 3
X2 - P in 23
X2 - P in 7
X2 - P in 24
X1 - P in 4
(Orientation = L ooking into X1 - P in 21

terminals on c onnec tor) X1 - P in 7

X1 - P in 22
P UR P LE = V inj (48 V OLT S ) X1 - P in 1
X1 - P in 23
Lt. B LUE = V ref (5 V OLT S ) X1 - P in 6
X1 - P in 24
G R E E N = S IG NAL C IR C UIT X2 - P in 2
X2 - P in 17
Dk B lue = Data C ommunication Link X2 - P in 6
B L AC K = G R OUND C IR C UIT X2 - P in 18
F UE L INJE C T OR S
R E D = 12 V OLT S (V B att) X1 - P in 2
X1 - P in 19

** G old P lated P ins X1 - P in 5

X1 - P in 20
X2 - P in 4
X2 - P in 19
X2 - P in 8
X2 - P in 20
3

X2 - P in 1
9 1 6
8 2 7

X2 - P in 21
C ontrolModu e

X2 - P in 5
G low P lug

X2 - P in 22
X1 - P in 3
X1 - P in 17
2 1 4 3 2 1 4 3 2 1 4 3 2 1
4 X1 - P in 8
3
X1 - P in 18
3

X3 - P in 5
9 1 6

X3 - P in 10
8 2 7

C ylinder #3 C ylinder #5 C ylinder #7

C ylinder #1 Injec tor P inout
S iemens
1 - Open C oil P ower F IC M
2 - Open C oil G round Module
D 3 - C los e C oil P ower
C 4 - C los e C oil G round
B
A
NOT E : F or clarity of the print all three F IC M
connectors are s hown together as one.
T he pin numbers are color coded, blue
for X1, red for X2, and black for X3

66
 
E C O N O L I N E ( D U A L A LT. )

12 Way On/Off E ngine /Trans C onnec tor

T C IL V P WR
5
R LC
3
A/C C lutch (-) Type 4
7 G round
A/C C lutch (+)
2 PCM
4 F IC M P ower P ower
A/C R elay F P R elay B ack UP Lamp
V P ower R elay R elay
10 K E YP WR R elay C ontrol
F IC M G round V P WR VPW Fuel Pump
1
Type 4 B+ V P WR
G round R
F IC M Main P wr B+ B+ B+ B+
12 B+
F IC M Logic P wr 10 Amp
50 Amp
MP R
6 M
8
K ey P ower K E YP WR
9 Inertia
Type 4
E OP S witch G round S witch
11
8 Way On/Off DFCM Mod
I-S ens e E ngine C onnec tor LH B K P R H BKP
6 Lamp Lamp
7
8
3

G E N2C
2 Vehic le Mounted C omponents
5 B AP
G E N1C INS T R UME NT
4 MA P
C L US T E R MA F /IAT 1
1 R egulator
Diagnos tic s C onnec tor K E YP WR S ens e
J1- C 1 P oc ket B+
G E N1C 1 P C M122 C has s is
G E N2C 4 C onnec tor (46 1 8 R PM MP H
T P WR G ND
FS S
V B P WR 46
22
6
Way)

34, 46
** V P WR
K AP WR B +
9 16

B+
Powertrain CAN
Data Bus
I-S ens e

A B C D E **
F 2 1
40 APCM
F C -V P WR G ND CAN1H
14 11, 23 CAN1L Module A F I
VGTC H 11 FPM
19 3
EP AC C R A lternator
27 2
VR E F 36 FPC
5
S IG R T N B US (+)
25

P WR G ND
32

V P WR
IAT 2 45 B US (-)
44
ECT 32 FE PS
39
E OT 44 S C IL
9
IC P AC P S W
29 16 Type 2

S IG R T N RCS - NO G round
C MP + 31 33
C MP - 43 VR E F
45
P WR G ND 42 MAF
42
CKP + 30 MAF R T N
21
CKP - 41 IAT 1
43
IP R 2 B AR O
38
VGTC MAP
10 41
E GR VC PBPP
23 17 Type 2

E GR VP G E NIL G round
33 30
E GR TP AP P 1
38 26
E GR TPC1 S IG R T N2
12 20 1
E GR TPC2
GPE
GPD
24

17
3
25
29
37
AP P 3
VR E F2
AP P 2
4
**
F IC MM AC C S RCS - NC
28 8
C AN2H T C S (Auto) 8 5
37 36 V P WR To AC
C AN2L S ys tem Starter Relay
26 C P S W - NC CTRL Ignition Switch
CKPO BPS
19 28 V P WR START
C MP O BPP NC
20 18 B+ Type 2 B+
T R O_P N NO G round
T HR E E
** J1- C 2 P oc ket 4 TR ACK
WF S DF C M
P C M122 E ngine 15 P E DA L
DOL Water In Fuel Probe
C onnec tor (46 3 Tripminder Module Horn Relay

**
Way) VS O CTRL
22
CTO B+
1 To Horn
TPO After Market B+
7
Circuits
12
PTO M
VS S N/C Powertrain CAN Pressure Ctrl
35 Solenoid #1
C AN1H Data Bus
V is teon 13 C R UIS E C ONT R OL Starter Motor
C AN1L
P C M122 14 Pressure Ctrl
E BS ON
27 N/C Solenoid #2
SCCS R E S UME S E T /AC C C OAS T
31 Horn Switch
12A 650-??? S CC S R TN OF F 2200 680
120

24 Ohms Ohms Ohms Pressure Ctrl

Module C S E G ND Type 6 Solenoid #3
10 G round

24 Way
TS PC 1 Trans mis s ion Pressure Ctrl
7 7
R LC C onnec tor 5R110 Transmission Wiring Assembly Solenoid #4
3 Dual 16 Way On/Off 20
T C IL Trans C onnec tor
5 24
PCA 2 Pressure Ctrl
9 12
PCB Solenoid #5
10 3 3
PCC 4
11 5 Converter
PCD 5
12 4 Clutch Ctrl
PCE 6 Solenoid
13 1
PCF 7
14 8
Line Pressure
2 PCG 8 10 Solenoid
PSA 9
17 N/C 14
PSB 10
18 N/C 16
PSC 11 TR S T S S /IS S OS S
19 N/C 9
PSD 12
20 N/C 11
13
PSE N/C
21 1 18
26 TFT 2 22
T S IG R T N
30 4 21
V B P WR
1 6 15
25 T R -P 3 17
22 T P WR G ND 5
TS S
29 8
IS S
27 7
OS S
28 9
T R O_N N/C
4 10
Nav-Int
Wiring
AFL Wiring
5
3

J1- C 3 P oc ket

** P C M122 Trans
C onnec tor (30 Way)

67
 DIAGNOSTIC CODES
C - Continuous Operation * - MIL (Malfunction Indicator Light) Illuminates
O - Self Test - Key On Engine Off (KOEO) ^ - O/D cancel flashes
R - Self Test - Key On Engine Running (KOER) [] - Assigned but not used
- Added/Changed for 2004 MY
DTC How Set Condition Description Fault Trigger/Comments Probable Causes
P0046 C* O R Turbo/Super Charger Boost Control Solenoid Circuit Internal to PCM. VGT Actuator Circuit check. Diagnostic circuit associated with 1 Amp driver checks for open
Range/Performance circuit, short to ground, and short to power.
P0069 C* MAP/BARO Correlation 30 kPa (4.4 PSI)/Compares BP and MAP at idle. VGT, BP, MAP, EGR - System Fault, Biased Sensor, Circuit Integrity.
P0096 C* Intake Air Temperature Sensor 2 Circuit 5 deg.C (41 deg.F)/Checks for minimum change in IAT2 IAT 2 Biased Sensor, System Fault, PCM.
Range/Performance
P0097 C* O R Intake Air Temperature Sensor 2 Circuit Low Input EGR disabled, less than 0.15 volts. MAT signal circuit, shorted to ground or defective sensor.
P0098 C* O R Intake Air Temperature Sensor 2 Circuit High Input EGR disabled, greater than 4.8 volts. MAT signal circuit, open, short to power or defective sensor.
P0101 C* Mass or Volume Air Flow Circuit Indicates a MAF range/performance problem was detected Damaged MAF sensor-plugged or restricted sensor supply tube-
Range/Performance during normal driving conditions when MAF is enabled. 4.0 MAF, PCM.
volts when RPM is less than 1500, 4.9 volts when RPm is
greater than 1500 RPM.
P0102 C* R Mass or Volume Air Flow Circuit Low Input Indicates MAF sensor circuit low input was detected during Open MAF sensor circuit-biased sensor, PCM-short to SIGN RTN or
KOEO Self Test or during continuous diagnostic monitoring. PWR GND on MAF sensor circuit-open in VREF circuit.
MAF voltage less than 0.35 volts.
P0103 C* O R Mass or Volume Air Flow Circuit High Input Indicates MAF sensor circuit high input detected during Biased sensor, PCM-MAF circuit shorted to VREF.
KOEO On-Demand Self Test or during continuous
diagnostic monitoring. MAF voltage is greater than 4.95V.
P0107 C* O Manifold Absolute Pressure/BARO Sensor Low Checks BP for a signal lower than a specified barometric Circuit is open, shorted to ground.
Input pressure expected for normal operations when BP is less
than 0.04 volts. Default 101 kpa (14.6 PSI).
P0108 C* O Manifold Absolute Pressure/BARO Sensor High Checks BP for a signal greater than a specified barometric Circuit is shorted to power
Input pressure expected for normal operations when BP is greater
than 4.9 volts. Default 101 kpa (14.6 PSI).
P0112 C* O R Intake Air Temperature Circuit Low Input Checks sensor output for a value higher than a maximum Shorted to ground.
probable temperature when IAT voltage is less than 0.15
volts. Default 77deg.F/25deg. C.
P0113 C* O R Intake Air Temperature Circuit High Input Checks sensor output for a value lower than a minimum Open in circuit, short to power.
probable temperature when IAT voltage is greater than 4.9
volts. Default 77deg. F/25deg. C.
P0117 C* O R Engine Coolant Temperature Circuit Low Input Checks ECT for a temperature higher than a specified oil Short to ground on the circuit.
temperature expected for normal operation when ECT
voltage is greater than 0.15 volts. Default 180deg. F/82deg.
C - no fast idle.
P0118 C* O R Engine Coolant Temperature High Input Checks ECT for a temperature lower than a specified oil Open in circuit, short to power.
temperature expected for normal operation when ECT
voltage is greater than 4.78 volts. Default 180deg.
F/82deg.C - no fast idle.
P0148 C Fueling Error Engine RPM has exceeded requested RPM. Alternative fuel source, Interference on CKP & CMP, Faulty PCM.
P0196 C* R Engine Oil Temperature Sensor Circuit Checks for an EOT temperature signal which is unable to Faulty, Biased sensor, circuit fault, PCM.
Range/Performance reach the EOT cold minimum limit whin a specified amount
of time. Function of initial EOT. (in-range fault based off of a
change in EOT and MFDES)
P0197 C* O R Engine Oil Temperature Sensor Circuit Low Input Checks EOT for a temperature higher than a specified oil Shorted to ground on the circuit.
temperature expected for normal operations when EOT
voltage is less than 0.15 volts. Default 212deg. F/100deg.C
- no fast idle.
P0198 C* O R Engine Oil Temperature Sensor Circuit High Input Checks EOT for a temperature lower than a specified oil Open in circuit, short to power.
temperature expected for normal operations when EOT
voltage is greater than 4.76 volts. Default 212 deg. F/100
deg. C - no fast idle.
P0219 C Engine Overspeed Condition PCM recorded excessive engine speed greater than 4300 Improper downshift, Interference on CKP & CMP, Faulty PCM.
RPM for more than 5 seconds.
P0230 C O R Fuel Pump Primary Circuit Fuel Pump Relay driver failure. Open control circuit, failed fuel pump relay or PCM.
P0231 C* O R Fuel Pump Secondary Circuit Low No voltage present at the Fuel Pump monitor circuit when it Indicates open, short circuit, relay, inertia switch or fuel pump.
has been commanded “on” for more than 1 second.
P0232 C O R Fuel Pump Secondary Circuit High Voltage present at the Fuel Pump monitor circuit when it has Indicates short to power,sticking relay.
NOT been commanded “on” for more than 1 second.
P0236 C* O Turbo/Super Charger Boost Sensor A Circuit Default inferred MAP - low power, slow acceleration, greater MAP sensor plugged, defective sensor.
Range/Performance than 120kpa(2.7PSI) at low idle.
P0237 C* O R Turbo/Super Charger Boost Sensor A Circuit Low Default inferred MAP - low power, slow acceleration, MAP MAP circuit short to ground or open, defective sensor.
voltage is less than 0.039 volts.
P0238 C* O R Turbo/Super Charger Boost Sensor A Circuit High Default inferred MAP - low power, slow acceleration, MAP MAP circuit short to Vref or Vbat, defective sensor.
voltage is greater than 4.91
P0261 C* O R Cylinder #1 Injector Circuit Low FICM detected a short in an injector circuit to ground. Injector circuit short to ground, defective coil.
P0262 C O R Cylinder #1 Injector Circuit High FICM detected an open injector circuit. Injector circuit open, defective coil
P0263 C Cylinder #1 Contribution/Balance When maximum/minimum pulse width adder is exceeded
and cylinder does not converge a fault is set.
P0264 C* O R Cylinder #2 Injector Circuit Low FICM detected a short in an injector circuit to ground. Injector circuit short to ground, defective coil.
P0265 C O R Cylinder #2 Injector Circuit High FICM detected an open injector circuit. Injector circuit open, defective coil
P0266 C Cylinder #2 Contribution/Balance When maximum/minimum pulse width adder is exceeded
and cylinder does not converge a fault is set.
P0267 C* O R Cylinder #3 Injector Circuit Low FICM detected a short in an injector circuit to ground. Injector circuit short to ground, defective coil.
P0268 C O R Cylinder #3 Injector Circuit High FICM detected an open injector circuit. Injector circuit open, defective coil
P0269 C Cylinder #3 Contribution/Balance When maximum/minimum pulse width adder is exceeded
and cylinder does not converge a fault is set.
P0270 C* O R Cylinder #4 Injector Circuit Low FICM detected a short in an injector circuit to ground. Injector circuit short to ground, defective coil.
P0271 C O R Cylinder #4 Injector Circuit High FICM detected an open injector circuit. Injector circuit open, defective coil
P0272 C Cylinder #4 Contribution/Balance When maximum/minimum pulse width adder is exceeded
and cylinder does not converge a fault is set.
P0273 C* O R Cylinder #5 Injector Circuit Low FICM detected a short in an injector circuit to ground. Injector circuit short to ground, defective coil.
P0274 C O R Cylinder #5 Injector Circuit High FICM detected an open injector circuit. Injector circuit open, defective coil
P0275 C Cylinder #5 Contribution/Balance When maximum/minimum pulse width adder is exceeded
and cylinder does not converge a fault is set.

68
 DIAGNOSTIC CODES
P0276 C* O R Cylinder #6 Injector Circuit Low FICM detected a short in an injector circuit to ground. Injector circuit short to ground, defective coil.
P0277 C O R Cylinder #6 Injector Circuit High FICM detected an open injector circuit. Injector circuit open, defective coil
P0278 C Cylinder #6 Contribution/Balance When maximum/minimum pulse width adder is exceeded
and cylinder does not converge a fault is set.
P0279 C* O R Cylinder #7 Injector Circuit Low FICM detected a short in an injector circuit to ground. Injector circuit short to ground, defective coil.
P0280 C O R Cylinder #7 Injector Circuit High FICM detected an open injector circuit. Injector circuit open, defective coil
P0281 C Cylinder #7 Contribution/Balance When maximum/minimum pulse width adder is exceeded
and cylinder does not converge a fault is set.
P0282 C* O R Cylinder #8 Injector Circuit Low FICM detected a short in an injector circuit to ground. Injector circuit short to ground, defective coil.
P0283 C O R Cylinder #8 Injector Circuit High FICM detected an open injector circuit. Injector circuit open, defective coil
P0284 C Cylinder #8 Contribution/Balance When maximum/minimum pulse width adder is exceeded
and cylinder does not converge a fault is set.
P0297 C Vehicle Overspeed Condition Vehicle has been driven at speeds above limited speeds Faulty PCM, Interference on VSS.
P0298 C* Engine Oil Over Temperature Condition Function of initial EOT Checks for an EOT temperature signal which is unable to reach th
EOT hot minimum limit (EOT_HOT_LMN) within a specified amou
of time.
P0299 C* Turbo / Super Charger Underboost Fault sets when the difference between EP and Faulty EP sensor, VGT control valve slow to respond, Stuck VGT
commanded EP exceeds the limit for > 30 seconds. valve, faulty PCM.
P0300 C* Random Misfire Detected Unknown or random misfire when calculated instantaneous
crankshaft acceleration exceeds a specified value a misfire
event is detected.
P0301 C* Cylinder #1 Misfire Detected Indicates when cylinder 1 is misfiring due to a loss of
compression.
P0302 C* Cylinder #2 Misfire Detected Indicates when cylinder 2 is misfiring due to a loss of
compression.
P0303 C* Cylinder #3 Misfire Detected Indicates when cylinder 3 is misfiring due to a loss of
compression.
P0304 C* Cylinder #4 Misfire Detected Indicates when cylinder 4 is misfiring due to a loss of
compression.
P0305 C* Cylinder #5 Misfire Detected Indicates when cylinder 5 is misfiring due to a loss of
compression.
P0306 C* Cylinder #6 Misfire Detected Indicates when cylinder 6 is misfiring due to a loss of
compression.
P0307 C* Cylinder #7 Misfire Detected Indicates when cylinder 7 is misfiring due to a loss of
compression.
P0308 C* Cylinder #8 Misfire Detected Indicates when cylinder 8 is misfiring due to a loss of
compression.
P0335 C* R Crankshaft Position Sensor A Circuit PCM monitors CKP signal for a unique pattern to indicate Poor connection, defective sensor, electrical noise.
piston position. Checks for total absence of the CKP signal.
P0336 C* R Crankshaft Position Sensor Circuit A CKP signal intermittent. Poor connection, defective sensor, electrical noise.
Range/Performance
P0340 C* R Camshaft Position Sensor A Circuit (Bank 1 or PCM monitors CMP signal for a unique pattern to indicate Poor connection, defective sensor, electrical noise.
single sensor) piston position. Checks for total absence of the CMP signal.
P0341 C* R Camshaft Position Sensor A Circuit CMP signal intermittent. Poor connection, defective sensor, electrical noise.
Range/Performance (Bank 1 or single sensor)
P0381 C* O Glow Plug/Heater Indicator Circuit Indicator Circuit Check - Instrument cluster driver checks for Open/Short circuit, lamp, fuse, PCM.
open circuit, or short circuit when lamp turns on and off.
P0401 C* Exhaust Gas Recirculation Flow Insufficient EGR Valve Position does not match desired, limits based on EGR Valve stuck or sticking - EGR Valve Position Sensor Bias -
Detected engine speed / load. EP Sensor bias.
P0402 C* Exhaust Gas Recirculation Flow Excessive EGR Valve Position does not match desired, limits based on EGR Valve stuck or sticking - EGR Valve Position Sensor Bias -
Detected engine speed / load. EP Sensor bias.
P0403 C* O R Exhaust Gas Recirculation Control Circuit EGR actuator circuit check. Diagnostic circuit associated Open circuit, short to ground, and short to power.
with 1 Amp driver Internal to PCM.
P0404 C* Exhaust Gas Recirculation Control Circuit +/- 0.10 EGRP error from commanded to actual EGRP dur- Faulty EGR sensor, valve or PCM integrity of EGR position circuit
Range/Performance ing normal driving conditions.
P0405 C* O R Exhaust Gas Recirculation Sensor A Circuit Low EGR is disabled when EGR voltage is less than 0.30 volts. EGRP circuit short to ground or open, defective sensor.
P0406 C* O R Exhaust Gas Recirculation Sensor A Circuit High EGR is disabled when EGR voltage is greater than 4.9 volts. EGRP circuit short to Vref or Vbat, defective sensor.
P0407 C* O R Exhaust Gas Recirculation Sensor B Circuit Low Checks EGRP for a lower than a specified position for Circuit is shorted to ground.
normal operation.
P0408 C* 0 R Exhaust Gas Recirculation Sensor B Circuit High Checks EGRP for a higher than a specified position for Circuit is shorted to 5V.
normal operation.
P0460 C* O R Fuel Level Sensor Circuit Fuel Level Indicator (FLI) Circuit Check - Instrument cluster "REFER to the appropriate section in the Workshop Manual."
driver checks for open circuit, or short circuit.
P0470 C* O Exhaust Pressure Sensor Maximum EP when the engine is not running 150 kpa (21.8 Faulty EP Sensor, PCM.
PSI) absolute.
P0471 C* Exhaust Pressure Sensor Range/Performance Minimum EP when the engine is running, Pressure differ- Faulty EP Sensor, PCM or VGT.
ence of +/-10 kPa (1.5 PSI) from desired.
P0472 C* O R Exhaust Pressure Sensor Low Input EGR disabled, default inferred for VGT operation when EGR EP circuit is short to ground or open, defective sensor.
voltage is less than 0.03 volts.
P0473 C* O R Exhaust Pressure Sensor High Input EGR disabled, default inferred for VGT operation when EGR EP circuit is short to Vref or Vbat, defective sensor.
voltage is greater than 4.8 volts.
P0478 C* Exhaust Pressure Control Valve High Input EP is higher than EP desired by 260 kpa (37.7 PSI) for Faulty EP sensor, VGT control valve slow to respond, Stuck VGT
greater than 30 seconds. valve, faulty PCM.
P0480 C R Fan 1 Control Circuit
P0487 C* O R EGR Throttle Position Control Circuit EGR actuator circuit check. open circuit, short to ground, and short to power.

P0488 C* EGR Throttle Position Control Range/Performance Checks for a difference in commanded and actual EGRTP Fault sets when the difference between EGRTP and commanded
EGRTP exceeds the limit for a specified time.
P0500 C Vehicle Speed Sensor A Vehicle speed sensor malfunction. Sensor, circuit, PSM, PSOM, low transmission fluid.
P0528 C R Fan Speed Sensor Circuit No Signal

P0562 C* O R System Voltage Low PCM voltage less than 7v - cause of no start/misfire. Low VBAT, loose connections/resistance in circuit, Vref engine
concerns.
P0563 C O R System Voltage High PCM voltage continuously more than 23.3v. Charging system fault.
P0565 C O R Cruise Control ON Signal KOER switch test(code set if cruise not present). Open/short circuit, switch failure, PCM failure.
P0566 C O R Cruise Control OFF Signal KOER switch test(code set if cruise not present). Open/short circuit, switch failure, PCM failure.
P0567 O Cruise Control RESUME Signal KOER switch test(code set if cruise not present). Open/short circuit, switch failure, PCM failure.
P0568 O Cruise Control SET Signal KOER switch test(code set if cruise not present). Open/short circuit, switch failure, PCM failure.
P0569 O Cruise Control COAST Signal KOER switch test(code set if cruise not present). Open/short circuit, switch failure, PCM failure.

69
 DIAGNOSTIC CODES
P0571 O Brake Switch A Circuit Brake switch A circuit malfunction Cruise control code will be set on every switch test on vehicles not
equipped with cruise control.
P0603 C Powertrain Control Module Keep Alive Memory No historical faults output during self test. Disconnected/Discharged Battery, Open PCM pin, faulty PCM.
(KAM) Error
P0605 O Powertrain Control Module Read Only Memory PCM failure Defective PCM.
(ROM) Error
P0606 C* O R ECM / PCM Processor
P0611 C* O R Fuel Injector Control Module Performance FICM memory fault will set if a RAM or ROM fault exists.
P0620 C O R Generator 1 Control Circuit
P0623 C O R Generator Lamp Control Circuit
P0645 C O R A/C Clutch Relay Control Circuit
P0649 C O R Cruise Control Lamp Control Circuit
P0670 C* O R Glow Plug Module Control Circuit Glow plug control module control line failure Open/grounded circuit, open/shorted GPCM, failed PCM
P0671 C* O R Cylinder 1 Glow Plug Circuit Glow plug #1 failure Open/shorted circuit, faulty glow plug, failed GPCM
P0672 C* O R Cylinder 2 Glow Plug Circuit Glow plug #2 failure Open/shorted circuit, faulty glow plug, failed GPCM
P0673 C* O R Cylinder 3 Glow Plug Circuit Glow plug #3 failure Open/shorted circuit, faulty glow plug, failed GPCM
P0674 C* O R Cylinder 4 Glow Plug Circuit Glow plug #4 failure Open/shorted circuit, faulty glow plug, failed GPCM
P0675 C* O R Cylinder 5 Glow Plug Circuit Glow plug #5 failure Open/shorted circuit, faulty glow plug, failed GPCM
P0676 C* O R Cylinder 6 Glow Plug Circuit Glow plug #6 failure Open/shorted circuit, faulty glow plug, failed GPCM
P0677 C* O R Cylinder 7 Glow Plug Circuit Glow plug #7 failure Open/shorted circuit, faulty glow plug, failed GPCM
P0678 C* O R Cylinder 8 Glow Plug Circuit Glow plug #8 failure Open/shorted circuit, faulty glow plug, failed GPCM
P0683 C* O R Glow Plug Control Module to PCM Communication GPCM glow plug control module communication line failure Open/shorted circuit, failed GPCM, failed PCM
Circuit
P0700 C O R Transmission Control System (MIL Request)
P0703 R Brake Switch B Input Circuit KOER switch test. Open/short circuit, switch, PCM, failed to activate during KOER
switch test.
P0704 C R Clutch Switch Input Circuit KOER switch test. Open/short circuit, switch, PCM, failed to activate during KOER
switch test.
P1000 C O R OBD Systems Readiness Test Not Complete Drive cycle is not complete.
P1001 R KOER not able to complete, KOER aborted Conditions not met. A/C, Parking Brake, Clutch, PRNDL, (EOT, ETC.)
P1102 C* Mass Air Flow Sensor In Range But Lower Than
Expected
P1139 C O R Water in Fuel Indicator Circuit Indicates fault in circuit. Faulty sensor, Open or Short in circuit.
P1148 C O R Generator 2 Control Circuit
P1149 C* O R Generator 2 Control Circuit High
P1184 R Engine Oil Temperature Sensor Out Of Self Test Engine not warm enough to run KOEO CCT - aborts test. Engine not warm enough, leaking thermostat, circuit failure.
Range
P1260 C Theft Detected, Vehicle Immobilized

P1284 R Aborted KOER - Injector Control Pressure Regulator ICP failure--Aborts KOER CCT test See codes P2284, P2285, P2286, P2288, P2623
P1334 C R EGR Throttle Position Sensor Minimum Stop Checks for a maximum closed and a minimum open
Performance position voltage.
P1335 C R EGR Position Sensor Minimum Stop Performance Fault sets when the EGRP closed position exceeds the
maximum limit at initial key on.
P1378 C O R FICM Supply Voltage Circuit Low IDM detects logic power low, less than 7 volts. Low batteries, loose connections/resistance in circuit, defective relay.
P1379 C O R FICM Supply Voltage Circuit High IDM detects excessive voltage, greater than 16 volts. Charging system fault.
P1397 R System Voltage Out Of Self Test Range Voltage too high or low for glow plug monitor test.
P1408 R EGR Flow Out Of Self Test Range EGRC output circuit check - engine off test only EGR Control circuit open, short to Vref, Vbat, ground, defective coil.
P1464 O R A/C Demand Out Of Self Test Range Aborts KOER Test. A/C switch not in "off" position, A/C circuit short to power.
P1501 O R Vehicle Speed Sensor Out Of Self Test Range Aborts test - KOER on demand, CCT, or switch test. Vehicle speed detected during test, faulty VSS, PCM.
P1502 O R Invalid Test - Auxiliary Power Control Module Aborts test - KOER on demand, CCT, or switch test. APCM active while KOER test is running.
Functioning
P1531 R Invalid Test - Accelerator Pedal Movement Aborts test - KOER on demand, CCT test. Accelerator pedal incorrect position during test, faulty AP, PCM.
P1536 R Parking Brake Switch Circuit KOER switch test. Failed to activate switch during test, circuit, switch, PCM.
P1639 C* O R Vehicle ID Block Corrupted, Not Programmed
P1703 O R Brake Switch Out Of Self Test Range
P1705 O R Transmission Range Circuit Not Indicating Not in park during KOEO or KOER. Operator error, circuit failure, faulty sensor, PCM.
Park/Neutral During Self Test
P1725 R Insufficient Engine Speed Increase During Self Test
P1726 R Insufficient Engine Speed Decrease During Self Test
P2122 C O R Throttle/Pedal Position Sensor/Switch D Circuit Low
Input
P2123 C O R Throttle/Pedal Position Sensor/Switch D Circuit High
Input
P2127 C O R Throttle/Pedal Position Sensor/Switch E Circuit Low
Input
P2128 C O R Throttle/Pedal Position Sensor/Switch E Circuit High
Input
P2132 C O R Throttle/Pedal Position Sensor/Switch F Circuit Low
Input
P2133 C O R Throttle/Pedal Position Sensor/Switch F Circuit High
Input
P2138 C O R Throttle/Pedal Position Sensor/Switch D / E Voltage Pedal Sensors will use SAE D,E,F codes
Correlation
P2139 C O R Throttle/Pedal Position Sensor/Switch D / F Voltage Pedal Sensors will use SAE D,E,F codes
Correlation
P2140 C O R Throttle/Pedal Position Sensor/Switch E / F Voltage Pedal Sensors will use SAE D,E,F codes
Correlation
P2199 C* Intake Air Temperature 1/2 Correlation Correlation between IAT1 and IAT2 are not at expected Open/shorted circuit, bias sensor, PCM
values.
P2262 C* Turbo/Super Charger Boost Pressure not Detected - No boost pressure increase was detected. MAP hose, MAP sensor, CAC system leaks, Intake leaks, EP
Mechanical sensor, exhaust restriction.
P2263 C* Turbo/Super Charger System Performance MAP hose, MAP sensor, CAC system leaks, Intake leaks, EP
sensor, exhaust restriction, exhaust leaks.
P2269 C O R Water in Fuel Condition Indicates water in fuel. Drain water in fuel separator, defective WIF sensor, circuit integrity.

P2284 C R Injector Control Pressure Sensor Circuit Default inferred ICP, ICP desired does not equal ICP See diagnostic manual - ICP system.
Range/Performance signal, difference of 362psi/2.5mpa.

70
 DIAGNOSTIC CODES
P2285 C O R Injector Control Pressure Sensor Circuit Low Default open loop control - underrun at idle, ICP is less than ICP circuit short to ground or open, defective sensor.
0.04 volts.
P2286 C O R Injector Control Pressure Sensor Circuit High Default open loop control - underrun at idle, ICP is greater ICP circuit short, Vref or Vbat, defective sensor.
than 4.91 volts.
P2288 C R Injector Control Pressure Too High Default inferred ICP is used, ICP is greater than See diagnostic manual - ICP system.
3675psi/25mpa.
P2289 C O Injector Control Pressure Too High - Engine Off Default inferred ICP, KOEO ICP is greater than ICP signal ground, circuit open, defective sensor.
1161psi/8mpa.
P2290 C O Injector Control Pressure Too Low Default inferred ICP is used, ICP is below desired pressure See diagnostic manual - ICP system.
P2291 C Injector Control Pressure Too Low - Engine No start ICP is less than 725psi/5mpa. See diagnostic manual - ICP system
Cranking
P2552 C O R FICMM Circuit - Throttle/Fuel Inhibit Circuit No signal from the FICM Monitor circuit Circuit open/short, FICM, PCM
P2614 C O R Camshaft Position Output Circuit CMPO signal intermittent Poor connection, electrical noise. In CMPO from PCM
P2617 C O R Crankshaft Position Output Circuit CKPO signal intermittent Poor connection, electrical noise. In CKPO from PCM
P2623 C* O R Injector Control Pressure Regulator Circuit IPR circuit failure Open/grounded circuit, stuck IPR, loose connection
U0101 C O R Lost Communication with TCM
U0105 C O R Lost Communication with FICM
U0155 C O R Lost Communication with Instrument Cluster
U0306 C O R Software Incompatibility with Fuel Injector Control
Module

71
 GLOSSARY
Actuator Dual Timing System
A device which delivers motion in response to an electrical A timing system that uses both a CKP and CMP sensors to
signal. determine engine speed and rotational position.

Analog DVOM Digital Volt Ohm Meter

A continuously variable voltage. A meter that uses a digital display to indicate a measured
value. Preferred for use on microprocessor systems because
a DVOM has a very high internal impedance and will not load
APS Accelerator Position Sensor down the circuit being measured.
A potentiometer style sensor that indicates the operator's
pedal position.
ECT Engine Coolant Temperature Sensor
A thermistor style sensor used to indicate engine coolant
AWA Feature temperature.
A feature built into the high pressure oil rails used to dampen
noises that can be caused by the hydraulic system.
EGR Cooler
A device used to cool exhaust gases before they are returned
BARO Barometric Pressure Sensor to the intake air system.
An analog device which indicates atmospheric pressure
which allows the PCM to compensate for altitude. A BARO
sensor has three connections, signal return(gnd), BARO EGR Exhaust Gas Recirculation Valve
signal, and Vref. A valve used to control the flow of exhaust gases into the
intake manifold.

CAC Charge Air Cooling

A process of cooling the air coming out of the turbocharger EGRP Exhaust Gas Recirculation Valve
before it enters the engine. Position Sensor
A potentiometer style sensor that indicates the amount of
movement of the EGR valve.
Canister Style Oil Filter
An oil filter that requires only the element be replaced and not
the housing. EOT Engine Oil Temperature
A thermistor type sensor that indicates engine temperature.
CAN 
A communication protocol for data transfer between the EVRT Control Valve
control modules. See VGTCV Variable Geometry Turbocharger Control Valve.

CKP Crankshaft Position Sensor 

EVRT
A magnetic pickup sensor that creates a sine wave voltage The International Truck and Engine Corporation’s trademark
when the timing wheel on the crankshaft breaks its magnetic for its electronically-controlled turbocharger.
field. The CKP determines crankshaft position and speed.

FICM Fuel Injection Control Module

Closed Crankcase Breather An electronic unit which has the primary function of an
A ventilation system that recirculates crankcase vapors into electronic distributor for the injectors. It also is the power
the intake air system. supply for the injectors.

CMP Camshaft Position Sensor Glow Plug Sleeves

A magnetic pickup sensor that creates a sine wave voltage Stainless steel sleeves used to protect the glow plugs from
when a peg on the camshaft breaks its magnetic field. The coolant.
CMP determines which cycle the piston is in (compression or
exhaust).
GPCM Glow Plug Control Module
Module which supplies power to the glow plugs and identifies
Digital Fuel Injection variation in current flow to the glow plugs.
A fuel injection system that uses both an open and close
signal to control fuel injectors.

72
 GLOSSARY
IAT Intake Air Temperature Sensor Main Power Relays
A thermistor style sensor used to indicate air temperature (Two) Battery power relay switches for the PCM and FICM
before the charge air cooler. (modules) that are key power initiated and controlled by the
corresponding powered module.

ICP Injection Control Pressure

A variable capacitance style sensor used to indicate high MAP Manifold Absolute Pressure
pressure oil system pressure. A MAP sensor generates a digital frequency that indicates
manifold boost pressure above atmospheric pressure. The
signal is created by switching action caused by manifold
IAT2 Intake Air Temperature 2 Sensor pressure of a diaphragm connected to a capacitor circuit in
A thermistor style sensor used to indicate air temperature the sensor. The digital frequency increases as pressure
after passing through the charge air cooler. increases. A MAP sensor has three connection: signal
return(gnd), MAP signal, and Vref.

Impedance
A form of opposition to AC current flow measured in Ohms. Misfire Detection
Uses engine RPM changes during a firing cycle to determine
a low contributing cylinder.
I/O Injector Test
A test that can be performed using the WDS to disable one
injector at a time while watching Mfdes to determine a weak Modular Water Pump
contributing injector. Is a water pump that uses the front cover as a housing and
only the hub and impeller are replaceable.

IPR Injection Pressure Regulator

Controls injection oil pressure. An electrical signal to a Normally Closed
solenoid creates a magnetic field which applies a variable Refers to a switch or a solenoid that is closed when no
force on a poppet to control pressure. The quantity of fuel control or force is acting on it.
delivered to the combustion chamber is proportional to
injection control pressure.
Normally Open
Refers to a switch or a solenoid that is open when no control
IVS Idle Validation Switch or force is acting on it.
An on/off switch that indicates when the accelerator pedal is
in the idle position.
PCM Powertrain Control Module
The housing that contains the micro computer, Vref regulator,
KOEO Key on Engine Off Test input conditioners and output drivers.
A self-test operation that is performed with the ignition switch
in the ON position with the engine OFF.
POT Potentiometer
Converts a mechanical motion to a voltage value. Most often
KOER Key on Engine Running Test used to sense the position of a component. This sensor
A self-test operation that is performed with the ignition switch works as a variable voltage divider. The wiper arm is
in the ON position and the engine RUNNING. mechanically connected to the component desired to be
sensed. Potentiometers have three connections: Vref, signal
out, and ground.
Long Life Ethylene Glycol Coolant
A premium coolant, with an Ethylene Glycol base, that can be
used in a cooling system for an extended time without Pulse Width
needing to be changed. Long life coolants do not require the The length of time an actuator, such as an injector, remains
use of extenders. Long life coolants can be identified by its energized.
yellow color.

73
 GLOSSARY
Relative Compression Test
A test that can be run with the WDS to measure compression
of a cylinder relative to the other cylinders in the engine. This
test is accomplished by comparing the rpm of the engine
during each compression stroke.

Rocker Arm Carrier

A housing that the rocker arms and their fulcrums are
mounted to.

Thermistor
Sensor used to determine temperature. A thermistor changes
it's resistance value in relation to temperature change.
Increasing temperature results in decreasing resistance,
decreasing temperature results in increasing resistance. The
thermistor in conjunction with a current limiting resistor in the
PCM forms a voltage divider that provides a voltage signal
indicating temperature. Since the top half of the voltage
divider is the current limiting resistor and is internal to the
PCM, a thermistor sensor only has two connections, signal
return and ground.

Variable Capacitance Sensor

A sensor that is used to determine pressure. A variable
capacitance sensor changes it capacitance value in relation
pressure change. Increasing pressure results in a lower
capacitance, thus increasing return voltage. Decreasing
pressure results in a higher capacitance and a lower voltage.
Variable capacitance sensors are 3 wire sensors.

VBAT
Battery voltage.

VGT Variable Geometry Turbocharger

A turbocharger that has a turbine housing that can change
sizes through electronically controlled hydraulics.

VGTCV Variable Geometry Turbocharger

Control Valve
Could also be called EVRTCV. Controls oil flow in and out of
the VGT actuator in order to change the effective size of its
turbine housing.

VPWR
Battery voltage.

VSS Vehicle Speed Sensor

Normally a magnetic pickup style sensor that is mounted on
the tailshaft of the transmission to indicate ground speed.

74
 INDEX
A F
Actuators, 31 FICM (Fuel Injection Control Module), 7

AWA (Acoustic Wave Attenuation), 24 FICM Electrical Connectors, 11, 34

B FICM Mounting Brackets, 7, 11

Block Heater, 35
Fuel Filter Housing, 35, 40
C
Camshaft, 10 Fuel in Oil Diagnostics, 46

Compressor Inlet Hose, 9, 18 G

Glossary, 72
Crankcase Breather, 7, 18, 41
Glow Plugs, 10
Cylinder Balance Test, 51
GPCM (Glow Plug Control Module), 8, 36, 41
D
Damaged Crankshaft Trigger Wheel Diagnostics, 49 GPCM Mounting Bracket, 8, 11

DLC (Diamond Like Carbon) Coating, 27 Glow Plug Harness, 7, 8, 31, 35, 41

Diagnostic Charts 58 H
Heater Return Tube, 35
Diagnostic Trouble Codes, 68
High-Pressure Oil Leak Diagnostics, 48
E
EP (Exhaust Pressure) Sensor, 36, 41 High-Pressure Oil Rail Plugs, 25

EP Tube, 34 High-Pressure Pump, 27

EGR (Exhaust Gas Recirculation) Cooler, 9, 20 High-Pressure Pump Cover, 15, 32

EGR Throttle Plate, 19, 31, 35 High-Pressure Stand Pipe, 24

EGRTP (Throttle Plate) Actuator, 8, 31, 35 Horsepower, 6

EGRTP Sensor, 7, 30
I
Injector, 15
Emissions Label, 8
Injector clip, 14
Engine Serial Number, 41
ICP Block-Off Tools, 50
Engine Wiring Harness, 14
ICP sensor, 8, 11

75
 INDEX
ICP Sensor Gasket, 26 Turbocharger Mounting Bracket, 21

IPR Valve, 26 Turbo Oil Supply Line, 13

IPR Heat Shield, 27 Turbine Outlet, 35

Intake Manifold, 9, 19 Turbine Wheel, 19

N Twelve-Way Connector, 36
No Start Diagnostics, 43
U
O Upper Oil Pan, 9, 36
Oil Level Gauge, 34
W
Oil Fill Adapter, 35, 41 Water Pump, 11

Oil Filter, 36 Wavy High-Pressure Oil Rail, 24

Bypass Valve, 38 Wiring Diagrams, 60

Filter Cap, 36

Filter Header, 38

Filter Housing, 34

Oil Pan, 36

P
Power Junction Point, 34, 41

PCM Electrical Connector (46-way), 34

R
Remote Mount Oil Filter Lines, 34, 36, 38, 39

S
Sensors, 29

T
Torque, 6

Torque Charts, 54

76
 FCS-13930-MISC 12/3
© 2003 International Truck and Engine Corporation FCS-13930-MISC REVISION 0