Scribd
Upload
303 views4 pages

Citroen Xantia Modyfikacje AM1996

The document summarizes modifications made to the electrical system for the 1996 model year range, including: 1. Removal of a warning lamp and changes to instrument panel lighting. 2. Changes to how speed information is supplied to taximeters and tachymetric sensors. 3. Integration of additional functions into the wiper selector switch for certain trim levels. 4. Introduction of a new anti-theft device keyboard with a service mode and autodiagnostic system.

Uploaded by

ArturHeise
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
303 views4 pages

Citroen Xantia Modyfikacje AM1996

The document summarizes modifications made to the electrical system for the 1996 model year range, including: 1. Removal of a warning lamp and changes to instrument panel lighting. 2. Changes to how speed information is supplied to taximeters and tachymetric sensors. 3. Integration of additional functions into the wiper selector switch for certain trim levels. 4. Introduction of a new anti-theft device keyboard with a service mode and autodiagnostic system.

Uploaded by

ArturHeise
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

PAGE 1 - e1-t0zp0 - modifications to the electrical system : 1996 Model Year range

modifications to the electrical system : 1996 Model Year range SINCE RPO No. 06749 UNTIL RPO No. 07113

1 Instrument panel
Removal of warning lamp : side and tail lamps. Operation : when the ignition is switched on , the instrument cluster doesn't light up when the parking lights are lit, the instrument cluster brightens up Electric speedometer ; the speed information is supplied by a "Hall" effect sensor.

2 Taximeter
The speed information is supplied by a "Hall" effect sensor. The mechanical outlet of the "Hall" effect sensor is obturated. Connecting of taximeter : it can be necessary to have mechanical information of the vehicle's speed use an old tachymetric sensor ; part number 6160 24 N.B. : The tachymetric pinion isn't sold with the sensor, to be recuperated on the vehicle.

3 Switch wiper selector switch


Concerns : trim level , VSX. The whiper's switch integrates : screen wiper delay timer rear window whiper screen wash (rear)

4 Coded anti-theft device (ADC)


New "ADC" keyboard (see note all "ADC" types) : introduction of key S : service (operation) mode deletion of key D /N or -Service (operation) mode : makes it possible to hand your vehicle to somebody without revealing your personal code. The "ADC" keyboard is provided with an autodiagnostic system, connected to the diagnostic socket. Operating procedure , service (operation) mode.

PAGE 2 - e1-t0zp0 - modifications to the electrical system : 1996 Model Year range

Switch on the ignition. Enter the user's code ( 4 -figure code). Press button S : audible beep (1). Introduce the service code ( 4 -figure code). Press button S : the green LED will flash 6 times with 6 audible beeps (2). Switch off the ignition : the red LED remains on, accompanied by 4 audible beeps (for 10 seconds) (3). To cancel the service mode : switch on the ignition . Enter the user's code.

N.B. : (1). No audible beep : the service mode is not allowed to go into service mode, the user's code must have been used once, at least close the vehicle start the whole process again N.B. : (2). Long audible beep period : the service mode is not allowed enter code C 0 C the green LED will flash 4 times with 4 audible beeps switch off the ignition start the whole process again N.B. : (3) occurs each time the ignition is switched off and as long as the service mode is activated.

5 Electrical harness
The electric wires of the main harnesses are marked in accordance with the logical precised in the brochure "ELECTRICITY".

6 Fuse box , in the passenger's compartment


The new fuse box enables the modification of the supply of permanent consumers : supply of permanent consumers with "+" battery : "customer" arrangement supply of permanent consumers with "+" after contact : "factory" arrangement N.B. : See evolution note ; "Preparation of New Vehicles".

7 Utilities box
Location : on the front left wheel arch. Evolutions :

PAGE 3 - e1-t0zp0 - modifications to the electrical system : 1996 Model Year range

maxi fuses (extremely intensive consumers) engine operation relays connections to front harness

7.1 Maxi fuses A to D


Concerns : all models. Application chart. Marked : fuse box. A. Rating. 60 A. Electrical supply. Battery +. Protected functions. Anti-theft device : ignition on ; + accessories ; starter motor +. Anti-theft device : + after ignition switched off. Fuse box , in the passenger's compartment : line N 2 , of connector 2 black channels ; black plug. Fuse box , in the passenger's compartment : line N 1 , of connector 2 black channels . Lighting switch.

B.

40 A.

Battery +.

C.

80 A.

Battery +.

D.

60 A.

Battery +.

7.2 Maxi fuses E to H


Concerns : vehicle with air conditioning vehicle with automatic gearbox Turbo CT 2.1 Turbo D Turbo D Application chart. Marked : fuse box. E. F. Rating. 40 A. 40 A. Electrical supply. Battery +. Battery +. Protected functions. Electric cooling fan unit. Electric cooling fan

PAGE 4 - e1-t0zp0 - modifications to the electrical system : 1996 Model Year range

unit - or - not used. G. H. -. -. -. -. Not used. Not used.

8 Utilities box
New utilities box receiving micro relays (according to option). Functions : cruise control headlamp Location : left hand drive vehicles : in front left wheel arch right hand drive vehicles : in front right wheel arch Access : remove the mud shield.

9 Coupling of trailer
Applicable from RPO number : 6690. The trailer coupling harness is connected to a 4 paths connector, located behindthe right rear light. During connecting on 4 paths connector : cut, then isolate the wire connecting paths 1 and 3 of the connector on the vehicle's side. N.B. : If the trailer coupling and its harness have to be disassembled ; re-establish connection between paths 1 and 3 of the connector on the vehicle'sside.

You might also like