TRANSMISSION AND DISTRIBUTION

Monitoring power quality beyond EN 50160 and IEC 61000-4-30

by A Broshi and E Kadec, Elspec, Israel The standards currently in place provide minimum requirements, since they want to create a level playing field that allows analysers from different manufacturers to give the same results. It is good idea in concept, but it also acts as double edged sword. Manufacturers design their product to comply with these standards but typically do not provide data and measurements that would allow power quality analysis to go beyond current capabilities.

To f o l l o w t h e g u i d e l i n e s s e t o u t b y various standards and record faults or disturbances, today's meters rely solely on event-based triggers. While this method provides some information regarding an event, it does not allow for full analysis of all power parameters leading up to an event, during an event, or how the overall network recovers after an event. Due to limitations in memory storage, it is likely that even the data captured by such recording methods will not contain all of the power and energy parameters, which may prevent power quality problems from being solved. Objectives for power quality monitoring Collecting quality statistics This involves measuring the power quality conditions in general, mainly to analyse the overall performance of an electrical system's power quality. In many cases this is monitored for facility distribution networks, large regions or total value for a utility. Power quality contracts Customers who are sensitive to power quality may have a specific electrical power contract that outlines the minimum acceptable power quality level to be supplied by the utility. Power quality troubleshooting Analysis of power quality events, usually close to a problematic load or customer. The analysis may be driven from power quality failure, but preferably by continuous monitoring to detect potential problems. Power quality troubleshooting is the first stage, hopefully followed by corrective action that would improve the situation and prevent reoccurrence of the failure. However, the power quality statistics and contracts may also be followed by corrective action if the minimum power quality level is not achieved. Existing standards and trends The two most common power quality standards in use today are IEC 61000-4-30 [1] and EN 50160. IEC 61000-4 defines measurement m e t h o d s, d e s c r i b e s m e a s u r e m e n t formulas, sets accuracy levels and defines aggregation periods, and its main purpose is to provide common requirements for measurement devices. EN 50160 provides recommended levels for power quality parameters, including a time based percentage during which the energize - August 2010 - Page 32 levels should be kept (e.g., limiting voltage flicker to 95% of the time per week). Va r i o u s p a p e r s h a v e d i s c u s s e d t h e limitations of these current standards, [3,4]. The main concerns about the existing standards are:
Fig. 2: Line-to-ground event. Fig. 1: Compliance with EN 50160 at industrial customer's main service.

Fig. 3: Line-to-line voltages.

TRANSMISSION AND DISTRIBUTION

1st Generation pure online meters, either analog or digital, which provide the current information without any logging. 2nd Generation data loggers, either paper-based or paperless, which provide periodic data recording. 3rd Generation power quality analysers provide logging of selective data based on events. 4th Generation unlimited logging power quality analysers allow continuous logging of all raw data.

Fig. 4: Line-to-line voltage zoom out shows two collateral events.

The only way to achieve full comprehension of power quality and fault phenomena along with their impact is to record all power and energy parameters on a continual basis without relying on triggers or event-based protocols. Technology that compresses the raw data of both voltage and current waveforms has been developed to enable this. This technology compresses data in a typical 1000:1 ratio, reducing disk space required, easing communication requirements, allowing continuous logging of all power quality and energy information. Compression stores raw waveform data, and power quality and energy parameters are calculated in post-processing. This concept is explained in IEC 61000-4-30 (p. 78): "Raw un-aggregated samples are the most useful for trouble-shooting, as they permit any type of post-processing that may be desired". The following examples are taken from different sites throughout the world utilizing c o m p r e s s i o n t e c h n o l o g y. A l l f i g u r e s (except Fig. 12 and Fig. 14) show data from real sites equipped with continuous logging power quality analysers.

Fig. 5: Line-to-line plus line-to-neutral voltages.

Fig. 6: Adding currents.

EN 50160 compliance Fig. 1 shows the compliance to the EN50160 standard at the main service of an industrial customer. The supply is 22 kV fed through two transformers that serve a large number of motors. The customer complained that poor power quality from the local utility caused significant damages to equipment. As seen, the utility power is in compliance with EN 50160, with no interruptions, variations, unbalances, etc. The only parameter that is not 100% compliant all of the time is voltage dips, but at 98,1% of the time it is within the required limit of 95%. Whilst the power has remained "in compliance",meters and recorders that simply take and record minimal parameters are not capable of providing information required to solve power quality and fault problems. Plant and electrical distribution networks will still suffer production and deliver y interruptions and failures when in full compliance with standards. The key is to provide full information that identifies faults and disturbances that are seemingly outside the current guidelines, yet cause significant failures. Measurements taken to comply with the standards do not

Fig. 7: Voltage DIP event 16 cycles.

Time aggregations which hide some of the power quality issues Limiting the values for only a portion of the time Limiting the overall power quality variables to voltage quality only Identifying the contribution of each side (source and user) to the power quality

standards in an attempt to tighten power quality standards and improve network power quality [5]. New analysis concepts Standards reflect the existing technology c a p a b i l i t i e s. T h e y d o n o t s p e c i f y unreachable requirements, but try to urge the development of new technologies that will drive and necessitate improvements. There are four generations of power meters: energize - August 2010 - Page 33

To combat these limitations, several countries are modifying the IEC and other

TRANSMISSION AND DISTRIBUTION

make it clear who is responsible for the dips. Full Compliance with EN 50160 was not sufficient to provide any indication of power anomalies at the site. While experiencing unexplained production interruptions and equipment failures, the customer received misguided status according to the standards. All parameters One of the problems of EN 50160 is that it requires measurement of voltage only. IEC 61000-4-30 recommends adding current as well. On delta connections the measurements are typically limited to the line-to-line voltages only, as required by EN 50160 and others. This hides some problems. The event shown in Fig. 2 highlights a short circuit between the blue phase and ground. On the line to line voltage profile (the upper graph) it is noticed only slightly, but much less than required to be recorded as an event (10% threshold). The result is that a potentially damaging event would not be recorded or analysed. Another example of the importance of using line-to-ground measurement in delta networks is explained in Figs. 3 to 6. Fig. 3 shows a line-to-line event. Although this is useful, the central essence of power quality analysis is the identification of source(s) of failures. Fig. 4 shows a zoom out of this event to a total of 1s. This view reveals that something was wrong both before and after the event. Fig. 5 adds the line-to-neutral voltages and reveals the source. It started as a short circuit on the red phase, which created higher potential between each of the other two phases to ground, which resulted with breakthrough on the blue phase. The result is shown on Fig. 3 as sag on L3-L1, but the source of the problem is the fault between phase L1 and ground. Adding the current (Fig. 6) explains the aftershock event a voltage drop which resulted from simultaneous connection of many loads which were disconnected during the main event. The following example shows the additional benefit from adding line-to-ground voltages on delta networks. Additional parameters which help analysis are harmonics or frequency. Continuous logging Common practice is to use event based logging as the foundation for any power quality analysis. IEC 61000-4-30 even specifies that typically pre-trigger information of 1/4 of the graph should be included in the event. Fig. 7 shows a voltage dip on the main ser vice of large refrigeration factory. Based on the events logging concept, it shows 16 cycles (a common default recording length). In addition to the standard voltage logging, it shows also the current during the event. Since there is a current increase during the voltage drop, the rule of thumb for analysis is that this event is caused by the downstream user. Using

Fig. 8: Voltage DIP event zoom out.

Fig. 9: Voltage DIP event 2nd zoom out.

Fig. 10: Voltage DIP event 3rd zoom out.

Fig. 11: Same event other locations.

the data compression technology, it is possible to continuously store all electrical information. Fig. 8 shows a larger view of the same event (approx. 7 s more than 300 continuous cycles). In addition, it shows the frequency during the event. Frequency variation is the result of the balance between generation and demand. It is one of the most important parameters for controlling generation p o w e r. W h e n g e n e r a t i o n e x c e e d s demand, frequency increases and when the generation is less than the demand it decreases. As shown on the graph, 1 s after the event the frequency started to increase, indicating that generation energize - August 2010 - Page 34

was higher than demand. There are two possible reasons for this: (1) there was a problem in the generation which caused it to increase generation power, or (2) the demand was significantly reduced almost instantaneously, creating overgeneration. What apparently happened is that the dip was in a large geographical area and caused many loads to stop and subsequently, the demand to drop. Unlike the previous conclusion, this proves that the source of the dip was from a large geographical area. This conclusion identifies the responsibility for the event to lie with the utility.

TRANSMISSION AND DISTRIBUTION

the voltage is below 207 V (nominal 230 V minus 10%) 3,5% of the time while using one minute averaging it is below 207 V 28% of the time. Voltage flickering is another important power quality parameter that is characterised by slow measurement. IEC 61000-4-15 defines two periods for monitoring flicker 10 min (PST ST = short term) and 2 h (PLT LT = long term). In real life, many processes vary during the 10 min period which makes it difficult to check the flicker level in real time and to accurately determine the true nature and cause of flicker. A newly developed extended algorithm to the flicker standard allows analysis of flicker levels at 2 s resolution. The values are displayed on the same scale as standard PST/PLT which means that if the flicker level is kept constant, the values for 2 s, 10 min and 2 hrs are the same. Other time periods, such as 10 s and 1 min flicker measurement can be provided as well for further power quality investigation. High sampling rate The nature of some power quality phenomenon is very fast which requires r a p i d s a m p l i n g a n d l o g g i n g r a t e s. IEC 61000 4 30 does not specify what sampling rate to use. It discusses in general terms about sampling rates (p. 19): "To ensure that matching results are produced, class A performance instrument requires a bandwidth characteristic and a sampling rate sufficient for the specified uncertainty of each parameter." When the sampling rate is not sufficient, the power quality event may not be visible or may mistakenly be considered as another type. Fig.14 shows the same event in 64 (top) and 1024 (bottom) samples per cycle. In the top graph, the event would be classified as voltage sag/drop. However in 1024 samples per cycle, it is clear that the sag is actually transient-induced. Although the standard does not force minimum sampling rate, many class A analysers perform their measurements at 256 or more samples per cycle. However, due to memory and capacity limitations, they log the data in lower sampling rates (sometimes even as low as 16 samples per cycle only). Some analysers also limit the number of channels that are logged at the highest sampling rate(s), dramatically reducing the accuracy and reliable power quality investigation. Multipoint time-synchronised analysis Typical power quality events start from a single point/source and propagate throughout the network to different locations, impacting different elements of an electrical system in various ways. Some events are in actuality a combination of two or more anomalies that occur during the same time period. Monitoring at a single point (typically at interconnect locations) shows the affect at this location only. Usually it is not possible to determine the

Fig. 12: Averaging hides a large amount of information.

Fig. 13: Cycle-by-cycle measurements.

Fig. 14: Effects of sampling and recording rate.

What would be seen if we look at this event further on a larger scale? Fig. 9 shows quarter of an hour of data. The frequency change can be clearly seen and also other current peaks which happened before the dip. It can be assumed that the current peaks caused the problem, followed by regional collapse of the grid. Fig.10 shows approximately 1,5 h. one and a half hours of continuous data (the displayed RMS values are calculated from the stored data at 512 samples per cycle). The current peaks appear before, during and after the event and they are typical of this site. It was just a coincidence that a current peak occurred simultaneously with the voltage dip. The drop in the voltage caused the current peak to be smaller than the other ones.

Fig. 11 shows time-synchronised data of the voltage, current and frequency on two other locations, located 106 km from each other and 62 km/54 km from the original site. The voltage and frequency graphs and the distance explain that the event was indeed a large scale event. Rules of thumb are right in most of the cases, but not in all cases. Rapid parameter monitoring In order to overcome data storage capacity and processing power limitations, the standards recommend averaging periods for different parameters. Averaging hides a large amount of vital power quality information. An example taken from a paper by Sintef Energy Research, Norway shown in Fig. 12. Using 10 min averages, energize - August 2010 - Page 36

TRANSMISSION AND DISTRIBUTION

source of the event and more importantly, the root cause of the problem. It becomes even more difficult when there is more than one source for what may seem like a single event. In this case, any conclusion may be counteracted if only one source is isolated and the event continues to appear. Fig. 15 shows the voltage levels at an industrial customer who complained about equipment failures. Small dips were obser ved at the main ser vice, simultaneously with transients. When more than one analyser was installed, it showed that there were at least two sources for the voltage drop events. According to the voltage levels (the values in percentages to allow for comparison of different voltage levels), the event on the left started downstream of the right-hand side MCC, propagated upstream to the main service and then downstream to the other transformer. The event on the right side of the graph occurred in exactly the opposite direction. However, both of them appear similar when monitoring the main service only. Analysing event propagation based on RMS values is a good practice. More advanced propagation analyses can be done by analysing the time differences for RMS values or even the phase shift o f w a v e f o r m s. T h e I E C 6 1 0 0 0 - 4 - 3 0 requirement is very moderate, requiring a maximum time uncertainty of only plus/ minus one network cycle (16.7 / 20 ms), which means two samples from two analysers can differ by as much as 40 ms. As transient propagation is much faster, more accurate time synchronisation must be achieved to allow proper analysis. The most common technique for time synchronisation is the use of global positioning system (GPS). However, different analysers have different time accuracies with GPS, some varying by more than the minimum single cycle required by the IEC standard. Another technique is using local area network (LAN) synchronisation and it is much easier to implement (GPS requires a sky view to operate). Using sophisticated algorithms it is possible to achieve even single sample accuracy (i.e. tens of ms), depending on the LAN topology and traffic. Fig. 4 shows an expanded view of the left event in Fig. 3. The analysers are synchronised over the LAN and event propagation is easily monitored from the MCC up to the main service and down to the other transformer. Acknowledgement This article was presented at the Cigr 6th Southern Africa Regional Conference: Somerset West 2009 and is reprinted with permission. References
[1] I E C 6 1 0 0 0 - 4 - 3 0 : 2 0 0 3 , Te s t i n g a n d measurement techniques Power quality measurement methods 2003, pp. 81, 78, 19. [2] EN 50160:1999, Voltage characteristics

Fig. 15: Voltage DIP from different locations.

Fig. 16: Voltage DIP from different locations zoom.

of electricity supplied by public distribution systems [3] V Ajodhia and B Franken, Regulation of Voltage Quality, February 2007. [4] European Regulators' Group for Electricity and Gas (ERGEG), Towards Voltage Regulation in Europe, December 2006, pp. 13.)

[5] Norwegian Water Resources and Energy Directorate, Regulations relating to the quality of supply in the Norwegian power system November 2004.

Contact Wayne Bromfield, Impact Energy, Tel 031 201-7191, [email protected]

energize - August 2010 - Page 37