Brake Systems Application Guide

INDEX
INTRODUCTION
BRAKE SUMMARY AND KEY FEATURES TYPICAL DESCRIPTION AND APPLICATIONS HYDRAULIC BRAKES TYPICAL DESCRIPTION AND APPLICATIONS ELECTRIC BRAKES 3 4-7 8

BRAKE CALCULATIONS
SELECTING BRAKE TORQUE BASED ON MOTOR DATA CRANE HOIST BRAKING TORQUE CRANE TROLLEY BRAKING TORQUE SELECTING BRAKE SIZE BASED ON LOAD DATA OVERHAULING LOAD TORQUE BRAKE THERMAL CAPACITY OVERHAULING LOADS HYDRAULIC BRAKE SELECTION FOR BRIDGE BRAKES HYDRAULIC BRAKE TORQUE RATINGS AND THERMAL CAPACITIES DC MAGNETIC SHOE BRAKE TORQUE RATINGS AND THERMAL CAPACITIES 9 9 10 10 12 13 14 15 16 20

NOTE: Pages 9 through 14 describe brake calculations that in general apply to all style Gemco brakes. The hydraulic brake selection, pages 15 through 19 are specifically for hydraulic brakes used as bridge brakes for overhead cranes.

Brake Systems Application Guide

BRAKE SUMMARY AND KEY FEATURES
HYDRAULIC, MAGNETIC, AND ELECTRO-THRUST BRAKE SYSTEMS
Gemco Industrial Brakes stop virtually any type of industrial machine. Applications such as indoor and outdoor bridge cranes, gantries, heavy-duty cranes, high duty cycle cranes, lock and dam projects, stacker reclaimers, commercial laundry equipment, and heavy-duty industrial transfer equipment are just some of the uses for Gemco Industrial Brakes. These field-proven, high performance brake systems are tough and reliable, and they provide extended, trouble-free service. That because they are designed and built to exacting specifis cations by Gemco. For more than 40 years, Gemco has been an acknowledged leader in brake systems technology for heavy-duty industrial applications.

BRAKE SYSTEM KEY FEATURES SUMMARY

H HM AH
Hydraulically Applied Spring Applied Controlled Stopping Parking AISE Rated

AHM

CB

TM

ET

DB

H HM AH AHM CB TM ET DB

Manual Hydraulic Applied Brake System Manual Hydraulic Brake with Parking Air-Over-Hydraulic Brake System, for remote control Air-Over-Hydraulic Brake with Parking AC Brake, Spring Set DC Brake, Spring Set (Auxiliary Hydraulic Cyl. available) Electro-Thrust, Spring Set Release by Electro-Hydraulic Actuator (Auxiliary Hydraulic Cylinder Available) Electro-Thrust, Spring Set Release by Electro-Hydraulic Actuator (Auxiliary Hydraulic Cylinder Available)

Note: Custom design and special brake assemblies are available; please consult factory for application assistance.
3

Brake Systems Application Guide

TYPICAL DESCRIPTION AND APPLICATIONS HYDRAULIC BRAKES
DESCRIPTION:
Type H manually operated hydraulic brakes for smooth controlled service stops. Sizes are 6 through 18 with torque ratings 150 to 900 ft-lbs.; one and two brake systems.

TYPICAL APPLICATIONS:
Bridge brakes for overhead, gantries and heavy duty cranes. The hydraulic brakes described in the following pages have been utilized for many years in steel mill cranes, shipyards and other applications where an operator control stop is desirable.

DESCRIPTION:
Type HM brakes not only provide smooth controlled stopping but are also equipped with a spring applied parking actuator. Sizes for single brake systems 6 through 18 two brake systems 6 and 8 , .

TYPICAL APPLICATIONS:
Bridge brakes for outdoor cranes that require parking feature due to wind loads.

Brake Systems Application Guide

DESCRIPTION:
Type AH-ARC (Air/Hydraulic Air Remote Control) brake system for stopping large loads. Sizes one, two and four brake systems - 6 through 18 .

TYPICAL APPLICATIONS:
Large overhead crane brakes for ladle cranes and other hot metal cranes, usually four brakes systems.

DESCRIPTION:
Type AH-H RC (Air/HydraulicHydraulic Remote Control) brake systems with operator hydraulic control. Sizes one, two and four brake systems - 6 through 18 .

TYPICAL APPLICATIONS:
Bridge brakes for overhead crane with moving trolley cabs that require more than 60 feet travel.

Brake Systems Application Guide

DESCRIPTION:
Type AH-ERC systems for operating hydraulic brakes by radio or pendent control. Size one, two and four brake systems - 6 through 8brake.

TYPICAL APPLICATIONS:
Any remote radio or pendent control brake requirement for bridge brakes.

DESCRIPTION:
Type AH-ERC Conversion package adds remote control capability to existing H brake systems. Size one and two brake systems.

TYPICAL APPLICATIONS:
Field modification control capabilities manual system. for remote on existing

Brake Systems Application Guide

DESCRIPTION: Type AHM System. All three of the previously described air over hydraulic systems can be provided with parking. (AHMARC, AHM-HRC, and AHMERC).

TYPICAL APPLICATIONS: As previously described but with parking for outdoor crane applications.

DESCRIPTION:
Type TMH System for remote operation of D.C. Electric Brake assemblies. Auxiliary cab control also allows hydraulic operation for controlled braking. sizes are 4to 23 one and two brake systems. ,

TYPICAL APPLICATIONS:
Bridge brakes for overhead cranes. Since electric brake is spring set, parking feature is also present. Note: Auxiliary cab control is also available for EH style electro-thrust brakes.

Brake Systems Application Guide

DESCRIPTION:
Type CB brakes spring applied electrically released via solenoid. Sizes, 4 to 10 general , duty.

TYPICAL APPLICATIONS:
Light duty crane bridge brakes and holding brakes.

DESCRIPTION:
Type TM brakes spring applied electrically released via D.C. magnet coils. AISE sizes, Mill Duty.

TYPICAL APPLICATIONS:
Crane hoist, stationary hoist, drive roller brakes, and lock and dam motor brakes.

DESCRIPTION:
Type ET brake spring applied electrical release by A.C. or D.C. electro-thrust mechanism.

TYPICAL APPLICATIONS:
Bridge brakes, lock and dam project, stacker reclaimers, container cranes. Note: Auxiliary hydraulic cylinder is also available for manual cab control.

DESCRIPTION:
Type DB brake spring applied electrical release by A.C. or D.C. electro-thrust mechanism.

TYPICAL APPLICATIONS:
Bridge brakes, lock and dam project, stacker reclaimers, container cranes. Note: Auxiliary hydraulic cylinder is also available for manual cab control. 8

Brake Systems Application Guide

INTRODUCTION When selecting the proper brake for a specific application, there are several factors to consider; a few that need to be reviewed are brake torque, stopping time and/or deceleration rates, brake mounting, brake location, thermal rating, environment, and brake style. The brake systems manufactured by Gemco Industrial Brake Products are external friction brakes. Applications for which these brakes are suited can be classified into two general categories: non-overhauling and overhauling. A) Non-overhauling loads are typically horizontally moving masses such as crane bridges, crane trolleys, and horizontal conveyors. B) Overhauling loads tend to upin speed if a brake is not present, examples of run which are crane hoists, winches, lifts, and downhill conveyors. Type A (non-overhauling) loads require brake torque only to stop the load and will remain at rest due to friction. Type B (overhauling) loads have two torque requirements; the first is braking torque required to stop the load, and the second is the torque required to hold the load at rest.

SELECTING BRAKE TORQUE BASED ON MOTOR DATA

The full -load torque of a motor is a function of horsepower and speed and is commonly used to determine a brake torque rating. The brake torque rating is to equal or exceed the full load torque of a motor. The formula to calculate the full load motor torque is as follows: T = where: 5250 HP RPM S.F. T = = = = = 5250 x HP x S.F. RPM constant motor horsepower speed of motor shaft application service factor static brake torque

CRANE HOIST BRAKING TORQUE

Sizing of crane hoist brakes is typically based upon full load hoisting torque. The following is a brief summary of guidelines for hoist brakes. Each hoist on a crane should be equipped with at least one spring-set magnetic brake; hoists handling hot metal should be equipped with more than one brake. Brake rating expressed as a percent of hoisting torque at the point of brake application should be no less than the following: 1) 150% when only one brake is used. 2) 150% when multiple brakes are used and the hoist is not used to handle hot metal. Failure of any one brake shall not reduce braking torque below 100%. 3) 175% for hoists handling hot metal. Failure of any one brake shall not reduce brake torque below 125%. 9

Brake Systems Application Guide

CRANE TROLLEY BRAKING TORQUE Crane trolley brakes are typically sized with a torque rating less than the motor full load torque s (service factor less than 1.0) to provide a longer stopping time or a soft stop. Overhead crane trolley brakes are minimized to prevent sway of the hook and load. Typical service factor is 50% for soft stopping. SELECTING BRAKE SIZE BASED ON LOAD DATA For applications where high inertial loads exist or where a specific stopping time or distance is required, the brake should be selected based on the total inertia of the load. Total system inertia reflected to the brake shaft can be expressed as follows: WKT2 where: WKT2 WKB2 WKM2 WKL2 = WKB2 + WKM2 + WKL2 = Total reflected inertia to brake (Ib-ft2) = Inertia of brake wheel (Ib-ft2) = Inertia of motor rotor (Ib-ft2) = Equivalent inertia of load reflected to shaft (lb-ft2) brake

The following formulas apply when calculating inertia of systems with different rotational speeds or linear moving loads to brake shaft speeds.

Rotary Motion: WKb2 where: WKb2 WKL2 NL NB = = = = = WKL2 (NL / NB)2 Inertia of rotation load reflected to brake shaft (lb-ft2) Inertia of rotating load (lb-ft2) Shaft speed at load (RPM) Shaft speed at brake (RPM)

10

Brake Systems Application Guide

Horizontal Linear Motion: WKW2 where: WKW2 W V NB = W (V / 2pNB)2 = Equivalent inertia of moving load reflected to brake shaft (lb-ft2)

= Weight of linear load (Ib) = Linear velocity of load (ft/mm) = Shaft speed at brake (RPM)

With the total system inertia calculated, the required average dynamic torque for a desired stopping time can be calculated using the following formula: Td where: Td WKT2 NB t 308 = WKT2 x NB 308 x t

= Average dynamic braking torque (lb-ft) = Total inertia reflected to brake (lb-ft2) = Shaft speed at brake (RPM) = Desired stopping time (sec.) = Constant

To determine stopping time for a given brake torque this formula can be rewritten as follows: t = WKT2 * NB 308 x Td

For some brake styles the time required until the brake lining makes contact with the wheel may be significant. Time required to stop is then as follows: WKT2xNB 308 x Td = Time between signal and moment when brake torque is actually applied (sec.) t1 + 11

t where: t1

Brake Systems Application Guide

For linear applications, the dynamic braking torque can be calculated directly using the following formula: WxVxr Td = gxt where: Td W V g t r = = = = = = Average dynamic braking torque (lb-ft) Total weight of linear moving load (lb.) Linear velocity of load (ft/sec.) Gravitational acceleration constant (32.2 ft/sec2) Desired stopping time (sec.) Length of movement arm or wheel radius (ft.)

This formula is applicable on crane trolley or crane bridge brakes. OVERHAULING LOAD TORQUE Applications with a descending load, such as crane hoists, elevators, etc., require a brake with sufficient torque both to stop the load and to hold it at rest. The total system inertia reflected to the brake shaft speed should be calculated using the previous formulas. Next, the average dynamic torque should be calculated with the previous formula: Td = WKT2 * NB 308 * t

Next, the overhauling torque reflected to the brake shaft can be determined by the following formula: 0.159 * W * V To = NB where: To W V NB 0.159 = Overhauling dynamic torque of load reflected to brake shaft (lb-ft)

= Weight of overhauling load (lb.) = Linear velocity of descending load (ft/min.) = Shaft speed at brake (RPM) = Constant (1/2 p) 12

Brake Systems Application Guide

The total dynamic torque required for an overhauling load is the sum of Td and T0, as follows: Tt where: Tt = T d + To = Total dynamic torque for descending load

BRAKE THERMAL CAPACITY When a brake stops a load, the energy required to stop is converted to heat. This heat is absorbed by the brake and the wheel. The ability to absorb and dissipate heat without exceeding temperature limitations is known as thermal capacity. There are two types of thermal capacity. The first is referred to as the maximum energy the brake can absorb in one stop, or emergency stop. The second is the heat dissipation capability of the brake if it is for frequent stopping. The kinetic energy that must be absorbed and dissipated by the brake can be determined as follows: Rotational Loads: WKT2 X NB2 KEr where: KEr = 5875

= Kinetic energy of rotating load (ft-lb)

2 WKT2 = Inertia of the rotating load reflected to brake shaft (Ib-ft )

NB 5875 KEL where: KEL W V g

= Shaft speed at brake (RPM) = Constant W x V2 = 2g

= Kinetic energy (ft-lb) = Weight of load (lb.) = Linear velocity of load, (ft/sec.) = Gravitational constant (32.2 ft/sec2) 13

Brake Systems Application Guide

OVERHAULING LOADS In the case of overhauling loads, both the kinetic energy of the linear and rotating loads and the potential energy transformed into kinetic energy by the change in height must be considered. The potential energy transformed to kinetic energy is determined as follows: PE Where: PE W S = = = = WS Change in potential energy, (ft-Ib) Weight of overhauling load (Ib) Distance load travels (ft.)

Therefore, the total energy to be absorbed by the brake in stopping an overhauling load is: ET = KEL + KEr + PE

In general, a brake will repetitively stop a load at the duty cycle that the electric motor can repetitively start the load. For rotating or linear loads, the rate at which a brake is required to absorb and dissipate heat when frequently cycled is determined as follows: TC where: TC WKT2 NB N0 3,220,000 = = = = = WKT2 x NB2 x NO 3,220,000 Thermal capacity (HP - sec/min) Total system inertia (Ib-ft2) Shaft speed at brake (RPM) Number of stops per minute

= Constant

For overhauling loads the rate at which the brake is required to absorb and dissipate heat when frequently cycled is determined as follows: TC where: TC ET 550 N0 = = = = = ET x NO 550 Thermal capacity (HP-sec/min) Total energy brake absorbs (ft-Ibs) Constant Number of stops per minute 14

Brake Systems Application Guide

BRAKE SELECTION FOR BRIDGE BRAKES The following formulas apply for calculating linear loads such as bridge brake applications: KEL where: = KEL W V G R T Td W x V2 WxVxr Td = 2xg gxt = Kinetic energy (ft-lb) = = = = = = Weight (lb.) Linear velocity (ft/sec) Gravitational constant (32.2 ft/sec2) Wheel radius (ft) Stopping time Average dynamic torque (lb-ft)

Given in terms of tons, wheel diameter, gear ratios, etc., the specifications necessary to calculate crane bridge brakes include the following: Empty crane weight WE Full load crane weight WL Max. bridge speed FPM Stops per hour N Track wheel diameter DIA *Gear ratio brake shaft to track wheel R Number of brakes NB Acceleration rate A Min. deceleration rate dMN Max. deceleration rate dMX Drive motor inertia WKM2 _____Tons _____Tons _____Ft/Min. _____Number value _____Inches _____(To 1) _____Number value _____Ft/Sec2. _____Ft/Sec2. _____Ft/Sec2. _____(Lb-Ft2)

* Drive motor RPM can be used to verify gear ratios, etc., for a maximum speed and track diameter. In general, service bridge brakes should have sufficient thermal and torque range to stop the bridge within a distance of 10% of the full load speed with full load, or at a deceleration rate as specified by the original manufacturer.

15

Brake Systems Application Guide

The kinetic energy and torque calculations can be stated in terms of crane specifications as follows: Kinetic energy absorption rate, per brake per hour: KE = N x (FPM)2 x (WE + WL) 232 x NB

Minimum stopping torque (to stop empty crane at minimum deceleration rate): TMN = 2.59 x WE x dMN x DIA NB x R

Maximum stopping torque (to stop fully loaded crane at maximum deceleration rate): TMX = 2.59 x WL x dMX x DIA NB x R

HYDRAULIC BRAKE TORQUE RATINGS AND THERMAL CAPACITIES Using the table below, select the smallest brake size that will exceed KE and TMX calculations listed above. TMN calculations for air powered systems should be above Minimum torque limits below:
Max. Dynamic Torque per Brake (Ib-ft.)** Brake Size Max. KE per Brake per Hour (ft.-Ib) Type H 1Brake Type H 2-Brake or Type HM All Air Powered Min. Dynamic Torque, All Air Powered Systems (lb-ft.)

6x3 8x3 10 x 4 14 x 6 18 x 8

1.0 x 106 1.25 x 106 2.5 x 10 5.0 x 106 9.0 x 106

150 200 425 600 900

150 200 250 350 550

350 450 1000 1400 1800

25 50 75 125 175

**Based on 70 lb. pedal force, 8 max. pedal travel on Type H or HM manual systems.

16

Brake Systems Application Guide

Maximum stops per hour can be calculated using the following: N x (Max. KE per brake per hour) KE where: (Max. KE per brake per hour) = Value for brake size as shown in table above. Max. stops/hr. = The additional torque required to stop the drive rotor and the brake wheel inertia is normally insignificant and is ignored when the gear ratio (R) is less than about 10 x 1. If the gear ratio, and thus the drive rotor inertia is abnormally high, considerable torque may be needed just to stop the drive rotor. To calculate the additional torque needed to stop the drive rotor and brake wheel inertia, proceed as follows: 1. Complete the previous calculations to establish the prelimary brake size. BRAKE SIZE 6 x3 8 x3 10 x 4 14 x 6 18 x 8 BRAKE WHEEL INERTIA .55 lb-Ft2. 1.41 Lb-Ft2. 4.25 Lb-Ft2. 24.20 Lb-Ft2. 75.73 Lb-Ft2.

2. Record the following data from brake wheel inertia table above and additional data from previous calculations. WK2 Brake wheel Inertia WK2 Drive Rotor Inertia WK2 Total (Drive Motor and Wheel) R, Gear Ratio + _________________ Lb-Ft2. Lb-Ft2. _________________ Lb-Ft2. _________________ x1 _________________ ft/sec2. _________________ ft/sec2. _________________ inches

dMN Deceleration Rate dMX Deceleration Rate @ Full Load DIA, Track Wheel 3. Calculate No Load Drive Torque, TNLD: WK2Total x R x dMN 1.34 x DIA. =

________ x ________ x ________ _____________________________ = ________Lb-Ft. 1.34 x _______

4. Calculate Full Load Drive Torque, TFLD: TNLD X dMX = ________ x ________ = ________ Lb-Ft. dMN ________ 17

Brake Systems Application Guide

5.Calculate Total Minimum and Maximum Torques: TMN (previous) ___________Lb-Ft. TMX (previous) ___________Lb-Ft. TNLD TMNT + ___________ Lb-Ft. TFLD ___________ Lb-Ft. TMxT + Lb-Ft. Lb-Ft.

6.Check to determine that TMxT is still within the torque limits of the brake size selected. If necessary, recalculate the problem based on alternate brake size and brakewheel inertia. The chart below shows the dynamic torque values developed by manually operated brake systems. Maximum torques tabulated are developed at 70 lb. pedal force, the limit indicated by AISE and OSHA. Two maximum values are shown for 10 x 4, 14 x 6, and 18 x 8 brakes, as follows:

The chart below shows the dynamic torque ranges developed by air powered hydraulic systems. The maximum torques shown are developed by a 70 lb. force applied on the air treadle on Type A/H systems or applied on the pedal of the control cylinder on Type NHM-HRC systems. Air powered hydraulic systems include either a 1 x 5 or a 1 x 8 air hydraulic pressure cluster to apply the service brake. In addition, 10 14 and 18 brakes include either a 7/8 diameter or a , , 1-1/8 diameter service brake actuator. Hence, 6 and 8 brakes have two possible maximum torque limits, while 10 14 and 18have four possible maximum torque limits. , , The minimum torque limits shown are developed by light application of the treadle or pedal. Because of hysteresis and friction in the power system valves, it is not practical to consistently control less torque than the minimum calculated. 18

Brake Systems Application Guide

Static holding torque values tabulated below are those developed by the parking spring on the Type HM brakes. The brake must be correctly adjusted in order to get the holding torque tabulated. Brake Size Holding Torque, lb-ft. 6x3 35 8x3 50 10 x 4 450 14 x 6 550 18 x 8 700

19

Brake Systems Application Guide

TM, ET and DB SHOE BRAKE TORQUE RATINGS AND THERMAL CAPACITIES TM Torque Ratings Maximum Torque in Lbs.-Ft (Max.) Series Brake Shunt Brake 1/2 HR 1 HR 1 HR 8 HR 15 25 15 25 40 50 40 50 75 100 65 100 150 200 130 200 400 550 365 550 750 1000 650 1000 1500 2000 1300 2000 3000 4000 2600 4000 6750 9000 6000 9000 ET Torque Ratings
BRAKE STYLE ET8 ET10 ET13 ET16 ET19 ET23 ET30 Allowable Heat Absorption for Brake Wheels WHEEL DIAMETER (inches) 8 10 13 16 19 23 30 TORQUE LB.FT. (Max.) 100 200 550 1000 2000 4000 9000

TM 43 TM 63 TM 83 TM 1035 TM 1355 TM 1655 TM 1985 TM 2311 TM 3014

DB Torque Ratings BRAKE STYLE DB12 DB14 DB17 DISC DIAMETER (Inches) 12 14 17 TORQUE LB.FT. (Max.) 100 200 550

Wheel Size 4.5 6.0 8.0 10 13 16 19 23 30

Ft.-Lb. per Hour 396,000 660,000 990,000 1,716,000 3,300,000 5,016,000 7,425,000 10,890,000 18,150,000

AMETEK
PATRIOT SENSORS
6380 BROCKWAY ROAD PECK, MI 48466-9766 USA 800-325-8074 810-378-5511 Fax 810-378-5516 www.patriotsensors.com www.ametek.com