Scribd
Upload
820 views

Type of Adsorption Isotherm

The document describes 5 types of adsorption isotherms: Type I shows monolayer adsorption, exemplified by nitrogen on charcoal. Type II shows monolayer then multilayer adsorption, like nitrogen on iron. Type III exhibits multilayer adsorption from the start, like bromine on silica gel. Type IV first forms a monolayer then exhibits capillary condensation, like benzene on iron oxide. Type V also demonstrates capillary condensation without an initial monolayer, as with water vapor on charcoal.

Uploaded by

DrAmit Verma
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
820 views

Type of Adsorption Isotherm

The document describes 5 types of adsorption isotherms: Type I shows monolayer adsorption, exemplified by nitrogen on charcoal. Type II shows monolayer then multilayer adsorption, like nitrogen on iron. Type III exhibits multilayer adsorption from the start, like bromine on silica gel. Type IV first forms a monolayer then exhibits capillary condensation, like benzene on iron oxide. Type V also demonstrates capillary condensation without an initial monolayer, as with water vapor on charcoal.

Uploaded by

DrAmit Verma
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Type of Adsorption Isotherm

Five different types of adsorption isotherm and their characteristics are explained below.

Type I Adsorption Isotherm

Type I Adsorption Isotherm

The above graph depicts Monolayer adsorption. This graph can be easily explained using Langmuir Adsorption Isotherm. If BET equation, when P/P0<<1 and c>>1, then it leads to monolayer formation and Type I Adsorption Isotherm is obtained. Examples of Type-I adsorption are Adsorption of Nitrogen (N2) or Hydrogen (H) on charcoal at temperature near to -1800C.

Type II Adsorption Isotherm

Type II Adsorption Isotherm

Type II Adsorption Isotherm shows large deviation from Langmuir model of adsorption. The intermediate flat region in the isotherm corresponds to monolayer formation. In BET equation, value of C has to be very large in comparison to 1.

Examples of Type-II adsorption are Nitrogen (N2 (g)) adsorbed at -1950C on Iron (Fe) catalyst and Nitrogen (N2

Type III Adsorption Isotherm

(g)) adsorbed at -1950C on silica gel.

Type III Adsorption Isotherm

Type III Adsorption Isotherm also shows large deviation from Langmuir model. In BET equation value if C <<< 1 Type III Adsorption Isotherm obtained. This isotherm explains the formation of multilayer. There is no flattish portion in the curve which indicates that monolayer formation is missing. Examples of Type III Adsorption Isotherm are Bromine (Br2) at 790C on silica gel or Iodine (I2) at 790C on silica gel.

Type IV Adsorption Isotherm

Type IV Adsorption Isotherm

At lower pressure region of graph is quite similar to Type II. This explains formation of monolayer followed by multilayer. The saturation level reaches at a pressure below the saturation vapor pressure .This can be explained on the basis of a possibility of gases getting condensed in the tiny capillary pores of adsorbent at pressure below the saturation pressure (PS) of the gas.

Examples of Type IV Adsorption Isotherm are of adsorption of Benzene on Iron Oxide (Fe2O3) at 500C and adsorption of Benzene on silica gel at 500C.

Type V Adsorption Isotherm

Type V Adsorption Isotherm

Explanation of Type V graph is similar to Type IV. Example of Type V Adsorption Isotherm is adsorption of Water (vapors) at 1000C on charcoal. Type IV and V shows phenomenon of capillary condensation of gas.

You might also like