MB0044 Production and Operations Management

Assignment Set- 1 (60 Marks)

Q1. What is meant by Productivity? Write a brief note on Capital productivity.

ANSWER:
Productivity is a measure of the efficiency of production. Productivity is a ratio of production output to what is required to produce it (inputs). The measure of productivity is defined as a total output per one unit of a total input. Capital deployed in plant, machinery, buildings and the distribution systems as well as working capital are the components of the cost of manufacturing. Demand fluctuations, uncertainties of production owing to breakdowns, and inventories being created drag the productivity down. Therefore, strategies are needed to maximize the utilization of the funds allotted towards capital. The strategies included are: Outsourcing strategies Methods improvement Balancing of workstations Quality circles Rationalization of packaging methods

Outsourcing strategies When capacity requirements are determined it is easy to figure out whether some goods or services can be outsourced. Outsourcing can reduce the capital and manpower requirements. Also the available capacities can be used to augment core competencies thus reducing the cost of the product or service to the customer. However, lack of expertise, quality considerations, nature of demand and cost factors may restrict outsourcing. Lack of Expertise: The outsourced firm may not have the requisite expertise to do the job required. Quality Considerations: Loss of control over operations may result in lower quality. Nature of Demand: When the load is uniform and steady, it may not be worthwhile to outsource. Absence of supervision and control may be a hindrance to meet any urgent requirements of the customer. This affects the business especially if no production facilities are built in the organization. Cost: It may not be worthwhile when the fixed costs that go along with making the product does not get reduced considerably.

1 SMU ROLL No.571115106

MB0044 Production and Operations Management

Methods improvement Methods Improvement starts with Methods Analysis. The focus of this process is to find out how a job is done and breaking it down to elemental tasks so that they are amenable for analysis. This is done for both running jobs and new jobs. For a new job, the description becomes the input for analysis. For current jobs, the analyst depends on observations, records and suggestions of the persons involved in the job. When improved methods are suggested, they are implemented and records created for assessing the consequences of the methods improvement procedures. The analyst should involve all concerned persons in the process so that acceptance becomes possible and opportunities open up for further improvements. Moreover, the people actually involved would be interested in improving their productivity and will help the analyst in the process. Balancing of workstations Assembly lines carry out operations in a sequence so that the product gets completed in stages. Since the workflow has to be uniform and operations may require different periods for completion the necessity of Line Balancing is felt. Capacities at workstations are so adjusted that a product takes approximately the same amount of time during each stage in the process of assembly. Quality circles Kaoru Ishikawa is generally considered to have promoted the concept of Quality Circles. It is well known that he is the originator of fishbone diagrams to identify the root cause of any problem (See Figure 1.5 Example of a fishbone diagram). The causes for the existence of a problem are classified as pertaining to the material, processes or method or any factor that goes into production. The matter is further investigated and pursued till the exact cause is determined.

2 SMU ROLL No.571115106

MB0044 Production and Operations Management

Quality Circles use these principles in solving problems. A Quality Circle is composed of a small group of employees who genuinely care about others, and who preferably does similar work, that is: Meeting voluntarily with a leader on a regular basis Identifying the problems Analyzing the causes Recommending their solutions to management Implementing solutions, wherever possible

The teams select projects as per these problems and implement actions to achieve improvement in the processes with a view to improve quality. Since these activities are carried out without affecting the regular work and involve little involvement of the managers, team work gets reinforced and results in continuous improvement in methods and quality. The capital deployed is minimal, if at all and therefore productivity is enhanced. Rationalization of packaging methods With logistics becoming an important function of the supply chain and outsourcing becoming the norm, packaging has become an important aspect. Space is at a premium and therefore stacking and storing have to be more scientific. Movements inside the premises from one location to another location are being done with automated systems. Also there is a need for the packaging systems to be designed for safe transit and continuous monitoring both for quantities and operations need to be there. In case of outsourced products the materials used and their design should facilitate reuse of the same, which brings about economy.

Q2. A) What is Automation? B) What are the kinds of Automation?

ANSWER:
Automation is the use of scientific and technological principles in the manufacture of machines that take over work normally done by humans. Following figure shows a sample automation production process:

3 SMU ROLL No.571115106

MB0044 Production and Operations Management

For services, automation usually means increase in quality and productivity using labor saving devices. Automation is ideal when the service provided or the product manufactured is highly standardized. Some extent of automation can be designed even with customization, that is, product or services meant to produce or deliver low volumes specific to a requirement. The cost per unit determines the extent of automation required. Automation systems cost huge sums of money and therefore, a deep analysis of the various factors has to be done. The advantage of automation is that it has low variability and will be more consistent on a repetitive basis. On the shop floor variability causes loss of quality. Where is automation used? Automation in the banking sector has resulted in ATMs which save a huge amount of banks labor and it is found to have given greater customer satisfaction. In education, long distance learning technology helps in supplementing class room instruction. The facilitating goods that are used in this case are e-courses, web sites and videos.

There are three kinds of automation: fixed, programmable, and flexible. 1. Fixed: By its very nature, fixed automation is rigid. They are designed for high volume production and their rigidity ensures less variability. They are not amenable to change in product or process. They need minimal human intervention. Examples: Oil refineries and chemical processing units. 2. Programmable: Programming devices enable machines to operate automatically. The machines have sensing and control devices that enable this. The simplest of them called machine attachments replace human effort. They guide, locate, move, and 4 SMU ROLL No.571115106

MB0044 Production and Operations Management

achieve relative positions by means of cams, optical sensing, and load sensing mechanisms and activate the controls to remove human intervention. Numerically controlled machines read instructions and convert them to machine. Computers are used for controlling one machine or a number of them and they have programs written into them for operations. They are Computer Numerically Controlled or for short, CNC machines. 3. Flexible: Robots are higher in the order of automation as they perform a variety of tasks. They are designed to move materials by holding them in their arms and making precise movements according to programs written into the computers that reside in them. They simulate human actions. They can grip and hold tools with the help of sensors. These sensors are sensitive to touch and force to know that the material is to be held with the requisite pressure for the conduct of operations. Vision sensors are used for inspection, identification and guidance. They use optics based instruments to gather data and feed them to the computers for activating the other parts of the robot. With the help of automation, 100% inspection of components can be done which ensures highest quality. Identification and movement of materials are helped by bar codes which are read and fed into the system for monitoring quantity, location, and movement. They help the automated systems to sort information and provide information for effecting any changes necessary. To make effective use of automated machines, we need to have the Movement of materials from and to different stations as also stores, automated. Automated Storage and Retrieval Systems (ASRS), receive orders for materials from anywhere in the production area, collect materials and deliver materials to the workstations. To make effective use of automated machines, we need to have the movement of materials from and to different stations as also stores, automated. Automated Storage and Retrieval Systems (ASRS), receive orders for materials from anywhere in the production area, collect materials and deliver materials to the workstations. Computers and information systems are used for placing orders for materials, giving commands and adjusting inventory records which show the location and quantity of materials available/needed. Continuous updating gives a clear picture for all concerned to enable them initiate action to keep the throughput smooth. Automated Guided Vehicle Systems (AGVS) like pallet trucks and unit load carriers follow embedded guide wires or paint strips to reach destinations as programmed.

5 SMU ROLL No.571115106

MB0044 Production and Operations Management

Q3. What are the factors that influence Plant Location?

ANSWER:
Factors influencing Plant Location can be broadly divided into two types namely: general factors and special factors (See Figure Factors influencing plant location).

General factors The general factors that influence the plant location are listed below (See Figure 5.2 General factors influencing plant location). 1. Availability of land: Availability of land plays an important role in determining the plant location. Many-a-time, our plans, calculations and forecasts suggest a particular area as the best to start an organization. However, availability of land may be in question. In such cases, we will have to choose the second best location. 2. Availability of inputs: While choosing a plant location, it is very important for the organization to get the labor at the right time and raw materials at good qualities. The plant should be located: Near to the raw material source when there is no loss of weight. At the market place when there is a loss of weight in the material. Close to the market when universally available, so as to minimize the transportation cost.

6 SMU ROLL No.571115106

MB0044 Production and Operations Management

1. Closeness to market places: Organizations can choose to locate the plant near to the customers market or far from them, depending upon the product they produce. It is advisable to locate the plant near to the market place, when: The projection life of the product is low The transportation cost is high The products are delicate and susceptible to spoilage After sales services are promptly required very often The advantages of locating the plant near to the market place are: (i) Consistent supply of goods to the customers (ii) Reduction of the cost of transportation 2. Communication facilities: Communication facility is also an important factor which influences the location of a plant. Regions with good communication facilities viz. Postal and Tele communication links should be given priority for the selection of sites.

3. Infrastructure: Infrastructure plays a prominent role in deciding the location. The basic infrastructure needed in any organization are: Power: For example, industries which run day and night require continuous power supply. So they should be located near to the power stations and should ensure continuous power supply throughout the year. Water: For example, process industries such as, paper, chemical, and cement, requires continuous water supply in large amount. So, such process industries need to be located near to the water. Waste disposal: For example, for process industries such as, paper and sugarcane industries facility for disposal of waste is the key factor. 7 SMU ROLL No.571115106

MB0044 Production and Operations Management

4. Transport: Transport facility is a must for facility location and layout of location of the plant. Timely supply of raw materials to the company and supply of finished goods to the customers is an important factor. The basic modes of transportation are by Air, Road, Rail, Water, and Pipeline. The choice of location should be made depending on these basic modes. Cost of transportation is also an important criterion for plant location. 5. Government support: The factors that demand additional attention for plant location are the policies of the state governments and local bodies concerning labor laws, building codes, and safety.

6. Housing and recreation: Housing and recreation factors also influence the plant location. Locating a plant with the facilities of good schools, housing and recreation for employees will have a greater impact on the organization. These factor seems to be unimportant, but have a difference as they motivate the employees and hence the location decisions.

Q4. Explain about the seven basic Quality Control tool.

ANSWER:
Flow Chart, Check sheet, Histogram, Pareto Analysis, Scatter Diagram, Control Chart, and Cause and Effect Diagram are the basic seven control tools considered for achieving quality. (See Figure 6.2 for Quality control tools)

a) Flow Chart: Flow chart is a visual representation of process showing the various steps. It helps in locating the points at which a problem exists or an improvement is possible. 8 SMU ROLL No.571115106

MB0044 Production and Operations Management

Detailed data can be collected, analyzed, and methods for correction can be developed using flow charts. The various steps include: Listing out the various steps or activities in a particular job Classifying them as a procedure or a decision Each decision point generates alternatives. Criteria and consequences that go with decisions are amenable to evaluation for purposes of assessing quality. The flow chart helps in pinpointing the exact points at which errors have crept in. (See Figure 6.3 for Sample flow chart)

b) Check Sheet: Check sheets are used to record the number of defects, types of defects, locations at which they are occurring, times at which they are occurring, and workmen by whom they are occurring. The sheet keeps a record of the frequencies of occurrence with reference to possible defect causing parameters. It helps to implement a corrective procedure at the point where the frequencies are more. (See Table 61. for Sample check sheet)

The table shows that the number of defects 1 and 5 are not many as compared to defect no 2 which increased over the days and appears to be stabilizing at the higher side and therefore needs to be attended immediately. The column which shows days can be changed to observed by the hour, if need be. c) Histogram Histograms are graphical representations of distribution of data (See Figure 6.4 for Sample histogram chart). They are generally used to record huge volumes of data about a process. They reveal whether the pattern of distribution has a single peak, or many peaks and also the extent of variation around the peak value. This helps in identifying whether the problem is serious. When used in conjunction with comparable 9 SMU ROLL No.571115106

MB0044 Production and Operations Management

parameters, the visual patterns help us to identify the problem which should be attended to.

The values shown are the number of observations made regarding a parameter. Sometimes, the percentages are shown to demonstrate the relative contribution of each of the parameters. d) Pareto Analysis: Pareto analysis is a tool for classifying problem areas according to the degree of importance and attending to the most important. Pareto principle, also called 80-20 rule, states that 80 percent of the problems that we encounter arise out of 20 percent of items. If we find that, in a day, we have 184 assemblies having problems and there are 11 possible causes, it is observed that 80 percent of them, that is, 147 of them have been caused by just 2 or 3 of them. It will be easy to focus on these 2 or 3 and reduce the number of defects to a great extent. When the cause of these defects has been attended, we will observe that some other defect becomes predominantly observed and if the process is continued, we are marching toward zero defects. e) Scatter Diagram: Scatter diagram is used when we have two variables and want to know the degree of relationship between them (See Figure 6.5 for Sample scatter diagram). We can determine if there is cause and effect relationship between the variables and the degree of extent over a range of values of the variables. Sometimes, we can observe that there is no relationship, in which we can change one parameter being sure that it has no effect on the other parameter.

10 SMU ROLL No.571115106

MB0044 Production and Operations Management

We can see that the change in variable 2 does not have much effect on variable 1. The other interpretation can be that for a small change in variable 1, the effect on variable 2 is more. f) Control Charts: Control charts are used to verify whether a process is under control. Variables, when they remain within a range, will render the product and maintain the specifications. This is called the quality of conformance. The range of permitted deviations is determined by design parameters. Samples are taken and the mean and range of the variable of each sample (subgroup) is recorded. The mean of the means of the samples gives the control lines. Assuming normal distribution, we expect 99.97 percent of all values to lie within the Upper Control Limit (UCL) and Lower Control Limit (LCL) corresponding to +/- 3. The graphical representation of data helps in changing settings to bring back the process closer to the target. g) Cause and Effect Diagram: Cause and effect diagram represents all the possible causes which lead to a defect on quality characteristics. These are arranged in such a way that different branches representing causes connect the stem in the direction of the discovery of the problem (See Figure 6.6 for Sample cause and effect diagram). When each of them is investigated thoroughly we will be able to pin-point some factors which cause the problem. We will also observe that a few of them can have cumulative effect or even a cascading effect.

When we observe that we have excessive defects from a machine, we try to identify all possible sources of the causes of defects. We make a study of each of them and try to correct it.

Q5. Define Project Management. Describe the five Dimensions of Project Management. ANSWER:
Managing a project is the practice of controlling the use of resources, such as cost, time, manpower, hardware, and software involved in the project. It usually starts with a problem statement and ends with delivery of a complete product (See Figure 8.1 Project management). 11 SMU ROLL No.571115106

MB0044 Production and Operations Management

Project management involves understanding the scope and various processes in a project cycle.

Management is the technique of understanding the problems, needs, and controlling the use of resources such as cost, time, manpower and materials. a) Project cycle: A project cycle consists of the various activities of operations, resources, and the limitations imposed on them. b) Process: A process is part of the project which consists of simple and routine instructions to achieve a desired result of any activity of the project. A process is responsible for bringing about the changes in the inputs fed to the process and giving out the desired output. c) Resource: The resource of a project refers to manpower, machinery, money, and materials which are required in the project. d) Scope: Scope of the project refers to the various parameters that affect the project in its planning, formulation, and executions. e) Project cost: Project cost is the budgeted expenditure of the project

Q6. Write a brief note on Just-In-Time(JIT). ANSWER:

Just-In-Time (JIT) manufacturing is a process by which companies don't keep lots of excess inventory; instead, they manufacture a product as an order comes in. It is a management philosophy of continuous and forced problem solving. 12 SMU ROLL No.571115106

MB0044 Production and Operations Management

The objective of JIT manufacturing system is to: Eliminate waste that is, minimize the amount of equipment, materials, parts, space, and workers time, which adds a great value to the product Increase productivity

JIT means making what the market demands when it is in need. It is the most popular systems that incorporate the generic elements of lean systems. Lean production supplies customers with exactly what the customer wants, when the customer wants, without waste, through continuous improvement. Deploying JIT results in decrease of inventories and increases the overall efficiencies. Decreasing inventory allows reducing wastes which in turn results in saving lots of money. There are many advantages of JIT. JIT: Increases the work productivity Reduces operating costs Improves performance and throughput Improves quality Improves deliveries Increases flexibility and innovativeness

For industrial organizations to remain competitive, cost efficiencies have become compulsory. JIT helps in this process. It is extended to the shop floor and also the inventory systems of the vendors. JIT has been extended to mean continuous improvement. These principles are being applied to the fields of Engineering, Purchasing, Accounting, and Data processing. However, for organizations to completely implement JIT manufacturing system, they need to have a proper commitment along with the following basic facilities - proper material, quality, equipment, and people involvement.

13 SMU ROLL No.571115106