SERIES 90A

Installation and Configuration Manual

Publication 1085-355 Rev E May. 2010

AMETEK POWER Instruments 255 N. Union Street Rochester, New York 14605

Tel: (800) 881-4156 Fax: (585) 238-4945 Web: www.ametekpower.com

Please Read This First!

IMPORTANT NOTES
THOROUGHLY READ AND UNDERSTAND THE SAFETY SECTION BEFORE ATTEMPTING TO INSTALL AND ENERGIZE A SYSTEM ***** UNAUTHORIZED MODIFICATIONS OR REPAIRS WILL INVALIDATE THE AMETEK WARRANTY PLEASE CONTACT THE AMETEK CUSTOMER SERVICES DEPARTMENT BEFORE TAKING SUCH ACTIONS ***** STANDARD DEFAULT SETTINGS ARE INDICATED IN THIS MANUAL, TO WHICH SERIES 90A ANNUNCIATORS WILL BE SET SHOULD NO SPECIFIC CONFIGURATION OR SET UP DETAILS BE SUPPLIED WITH PURCHASE ORDERS

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Table of Contents
PRODUCT OVERVIEW ................................................................................................................ 1 SAFETY..................................................................................................................................... 1 Construction .............................................................................................................................. 1 System Front View ................................................................................................................. 1 System Rear View ................................................................................................................. 1 Module Cell ............................................................................................................................ 2
Cell Assembly ................................................................................................................................................... 2 Module Cell Configurations ............................................................................................................................... 3 Annunciator Windows ....................................................................................................................................... 3

Annunciator Model Code Definition ........................................................................................... 4 SYSTEM CONFIGURATION AND SET-UP ................................................................................. 6 Hardware Configuration ............................................................................................................. 7
Field Contact Type ............................................................................................................................................ 7 Field Contact Voltage (FCV) ............................................................................................................................. 8 CSM Address .................................................................................................................................................. 10

I/O Module Configuration ..................................................................................................... 11 I/O Module Configuration ..................................................................................................... 12 Display Module .................................................................................................................... 13 Common Service Modules ................................................................................................... 14 Communication Modules ..................................................................................................... 15
Serial............................................................................................................................................................... 15 Ethernet .......................................................................................................................................................... 16

Ground Fault Detector Module ............................................................................................ 17 Power Supply Modules ........................................................................................................ 17 Field Contact Voltage Supply Modules ................................................................................ 18 IRIG-B Module ..................................................................................................................... 18 INSTALLATION .......................................................................................................................... 19 Mounting .................................................................................................................................. 19 Panel Mounting (option PM, PC) ......................................................................................... 19 19 Rack Mounting (option RK) ........................................................................................... 21 NEMA Enclosure (option N4, N4PB) ................................................................................... 22 Surface (Wall) Mounting (option S) ...................................................................................... 23 Weather Tight NEMA Front Cover (option NCB, NCT) ....................................................... 25 External Power Supply Mounting ......................................................................................... 29
120/230VAC Power Supply............................................................................................................................. 29 125VDC Power Supply ................................................................................................................................... 29

Wiring ...................................................................................................................................... 30 Input Wiring.......................................................................................................................... 30 Common Field Contact Voltage ........................................................................................... 30 Isolated Field Contact Voltage ............................................................................................. 31
Input / Relay Wiring for Full Size Windows (using one I/O Card) .................................................................... 32 Input/Relay Wiring For Half Size Windows (using one I/O Card) ................................................................... 33 Input/Relay Wiring For Half Size Windows (using one I/O Card) ................................................................... 34 Input Wiring with Half Size Windows (using two I/O Cards) ........................................................................... 35 Repeat Relay Wiring for Half Size Windows (using two I/O Cards)................................................................. 36 Input/Relay Wiring for Quad Size Windows (using two I/O Cards) .................................................................. 38 Common Service Cell Wiring (with Integral Pushbuttons) ............................................................................... 39 Common Service Wiring (with I/O Modules) .................................................................................................. 40

Connecting Power ................................................................................................................... 41 120/230 VAC & 125VDC Input Power ................................................................................. 41 Field Contact Voltage .......................................................................................................... 41 Power Requirements ............................................................................................................... 42 External AC supply: ............................................................................................................. 42
SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL 1

Integral AC supply: .............................................................................................................. 42 Integral Power Supply ......................................................................................................... 43

125VDC or 120/230 VAC Integral Power Supply ............................................................................................44 125VDC or 120/230VAC Integral Field Contact Voltage (FCV) Supply ...........................................................45 120/230 VAC and 125 VDC Integral Power Supply Wiring..............................................................................46 24VDC Integral Power / FCV Supply...............................................................................................................47 48VDC Integral Power Supply .........................................................................................................................48 24 and 48 VDC Integral Power Supply Wiring .................................................................................................49

External Power Supply ........................................................................................................ 50

125 VDC External Power Supply Wiring .........................................................................................................51 120/230 VAC External Power Supply Wiring ...................................................................................................52

SOFTWARE CONFIGURATION ................................................................................................ 53 Application ............................................................................................................................... 53 Software Installation ................................................................................................................ 53 Software Configuration Instructions ........................................................................................ 54 Reviewing or editing the Factory Configuration ................................................................... 54 Creating a new Configuration .............................................................................................. 55 Software Configuration Menus ................................................................................................ 56 Main menu overview ............................................................................................................ 56
File Menu ........................................................................................................................................................56 Options Menu ..................................................................................................................................................56 View Menu ......................................................................................................................................................56 Connections Menu ..........................................................................................................................................56 Help Menu .......................................................................................................................................................56 File ..................................................................................................................................................................57 Options ............................................................................................................................................................59 View Configuration (Text) ................................................................................................................................60

Configuration Wizard ........................................................................................................... 65

System ............................................................................................................................................................66 Input Configuration ..........................................................................................................................................69 Alarm Numbering ............................................................................................................................................69 Switch Inputs ...................................................................................................................................................78 External Switch Function Settings ...................................................................................................................78 Test Configuration ...........................................................................................................................................79

Other System Configurations .............................................................................................. 79 Modbus ................................................................................................................................ 80

Settings for Ethernet (Option ETH) .................................................................................................................80 Common Modbus Settings ..............................................................................................................................81

DNP3.0 ................................................................................................................................ 83
Settings for Ethernet (Option ETH) .................................................................................................................83 Common DNP Configuration Settings .............................................................................................................84

SYSTEM SPECIFICATIONS ...................................................................................................... 87 Inputs....................................................................................................................................... 87 Display ................................................................................................................................. 87 Repeat Relay Outputs ......................................................................................................... 88 Alarm Sequence .................................................................................................................. 89 Controls ............................................................................................................................... 90 System Relays ..................................................................................................................... 90 Audible Devices ................................................................................................................... 90 Communications .................................................................................................................. 91 Time Stamped Alarms ......................................................................................................... 91 Power Requirements ........................................................................................................... 91 Mechanical .......................................................................................................................... 92 Connections / terminations .................................................................................................. 92 Environment ........................................................................................................................ 93 Electrical .............................................................................................................................. 93 Certifications ........................................................................................................................ 94
2 SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Servicing .............................................................................................................................. 95 Module Removal ...................................................................................................................... 95 ESD ......................................................................................................................................... 96 APPENDIX A .............................................................................................................................. 97 Operational Sequences ........................................................................................................... 97 LEGEND ............................................................................................................................ 102 APPENDIX B ............................................................................................................................ 103 Modbus Data Formats ........................................................................................................... 103 Alarm State Mode .............................................................................................................. 103 Point Mode ......................................................................................................................... 104 AN3135 Mode .................................................................................................................... 105 Event Data ......................................................................................................................... 106 Modbus Addresses ............................................................................................................107 Default Values ................................................................................................................... 107 APPENDIX C ............................................................................................................................ 108 DNP Data Formats ................................................................................................................ 108 Device Profile Document ....................................................................................................... 108 Implementation Table ............................................................................................................ 109 Pushbutton Controls .............................................................................................................. 110 SERIES 90A Data Map ......................................................................................................... 111 Binary Inputs ...................................................................................................................... 111 Binary Input Change with Time (SER Option) ................................................................... 111 APPENDIX D ............................................................................................................................ 112 Window Assembly Details ..................................................................................................... 112 Window Legends ............................................................................................................... 112 Window Colors ................................................................................................................... 112 Window Assembly ............................................................................................................. 113 APPENDIX E ............................................................................................................................ 115 Telephone / Fax Number List ................................................................................................ 115 PROCEDURES FOR FACTORY REPAIR AND RETURN ....................................................... 117 Warranty ................................................................................................................................ 117

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

SCOPE

This manual describes the installation and configuration of the SERIES 90A annunciator system. This includes operation of its associated configuration software. Glossary of Terms Cell: Refers to a single module housing that can accommodate several boards. An Annunciator that is 3 rows high by 4 columns wide consists of 12 Cells. Refers to an individual electronic board. There are a variety of boards used in the Annunciator System for inputs, outputs, communications, etc. Normally Open. Contact state is open when normal, closes upon alarm. Normally Closed. Contact state is closed when normal, opens upon alarm. Typically refers to the relay coil state when normal. The coil de-energizes (voltage removed) when in alarm or while activated. Typically refers to the relay coil state when normal. The coil energizes (voltage applied) when in alarm or while activated. Type of relay contact, SPST (single pole, single throw). Open in the normal state, closes upon alarm or while activated. Type of relay contact, SPST (single pole, single throw). Closed in the normal state, opens upon alarm or while activated. Type of relay contact, SPDT (single pole, double throw). Open and closed contact with common pole. Both change state when in alarm or while activated. Field Contact Voltage. Field contact or wetting voltage for alarm inputs. Common Service Module. The CSM provides common alarm controls and output relays. Typically located in the bottom right cell. Input/Output. This refers to a board that accepts the customer Field Contact Inputs, provides outputs to the LED Display and can provide optional repeat relays.

Module: N.O. N.C. Energized: De-Energized: Form A Form B Form C

FCV: CSM: I/O:

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

PRODUCT OVERVIEW
SAFETY
The following safety symbols are used on the SERIES 90A:

Caution, risk of danger. Refer to the Instruction Manual.

Caution, risk of electric shock.

Protective Earth Conductor Terminal The SERIES 90A is CE certified for operation under the following conditions: Indoor Use (unless mounted in NEMA-4 enclosure option) Altitude up to 2000 m Operating Temperature Range: Relative Humidity: Mains supply voltage fluctuations: Transient Over voltages: Category II) Pollution Degree 2 In product configurations with 125VDC or 120VAC Field Contact Voltage (options: D, DC, D/ISO, Y/ISO), the system must be equipped with the lockable front door (options NCB, NCT) or NEMA Enclosure (options N4, N4PB) Annunciator Model Code Definition on page 4. For FM option (refer to option codes), the required door may be supplied by Ametek, a panel shop or the customer. The door must meet the FM standard for requiring a tool to open or remove the door to allow access to the front of the Annunciator. Also, 120/230VAC & 125 VDC Input Power (options A, B, C) must use external power supplies, unless the front door or NEMA enclosure is used. All other product configurations can be installed in any enclosure as specified in the model number table, item 1. Installation and start-up must be carried out by trained and qualified personnel.
1

-20 TO 50 OC (-4 to 122OF) 20-95% RH +/- 10% of nominal 2500 V (Installation or Measurement

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

If the unit is not installed and operated as specified the protection provided by the unit may be impaired. Before start-up it is important to ensure that: Before start-up, it is important to ensure that: 1. 2. 3. 4. The unit can be switched off by a switch, or a circuit breaker, clearly marked as the disconnecting device for the unit. The minimum rating of the disconnecting device is: 5 Amps for 120 Vac or 230 Vac power 10 Amps for 24 or 48 VDC power The disconnecting device is located in close proximity to the unit and must be marked as the disconnecting device for the unit. The protective earth terminal is properly connected to protective earth. The line has been connected correctly and protection is provided against electric shock.

Proper ventilation is provided by at least 6 inches (15.25 cm) above and below the unit

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

CONSTRUCTION
The SERIES 90A is a modular design constructed from a matrix of cells up to 13 high by 13 wide. The cells can be configured for 1, 2, 3 or 4 points per cell. Each cell provides front access to the electronics and all wiring connections are made to the rear of the unit. Each cell can accept several modules in various combinations, consisting of I/O Cards, Common Service Modules, Power Supplies and Option Modules. The Common Service Module (CSM) is typically located at the lower right cell of the unit and the other cells are used for I/O.

System Front View

I/O Cell Window

I/O Cell Window

I/O Cell Window

SIL

ACK

CSM Cell
TEST RESET

Integral Pushbuttons

SYSTEM STATUS

FAIL

REMOTE COMM

GROUND FAULT

System Rear View

I/O Cell

I/O Cell

I/O Cell CSM Cell

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Module Cell
The Annunciator is a modular construction made from individual cells, allowing any size high or wide up to 13. All cards are removable from the front of the unit, after removing the window or pushbutton assembly.

Cell Assembly
7 5 1 9 3

8 10

6 13 11 14 12 4

Item # 1 2 3 4 5

Part Description Module Cell Window Divider Back-plane Housing Display Housing Rear Cell Housing

Item # 6 7 8 9 10

Part Description Display Board Back-plane Assembly Interconnect Board Module (see list) Row Interconnect Board

Item # 11 12 13 14

Part Description Window Housing Window Legend Color Diffuser Window

Available Modules:
2

I/O LED CSM

Input / Output Module, with optional Repeat Relays LED Display Module Common Service Module & Sequential Events Recording CSM COMM Communication Module: Serial & Ethernet) PS Power Supply: Integral AC/DC Universal, Integral DC/DC FCV Supply Field Contact Voltage Supply: Integral AC/DC Universal IRIG-B Time Synchronization Input Module used for Sequential Events Recording Ground Fault Ground Fault Detector Module
SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Module Cell Configurations

CSM CELL
Front View

I/O CELL
Front View

SLOT 1 CSM MODULE

SLOT 3 I/O MODULE

SLOT 4 INTEGRAL POWER SUPPLY OR IRIG-B MODULE

SLOT 1 & 3 I/O MODULES

SLOT 2 COMMUNICATIONS MODULE SERIAL OR ETHERNET

SLOT 4 INTEGRAL POWER SUPPLY OR INTEGRAL FCV SUPPLY OR GROUND DECTOR

Note: Slot 5 of the I/O cell is also used for a row to row interconnect board (item #10 on cell assembly figure), which is installed for every row of the Annunciator. When installed; no other card or power supply can be inserted in that slot. All other unused slot 5 positions in that row can be used for power supplies or a ground detector. (This will be factory configured)

Annunciator Windows
The Annunciator windows come in four sizes as shown below. Legends can be laser printed on transparency film and inserted into the window frame. Colored filters are inserted behind the legends. Reference the appendix for additional details.
FULL SIZE WINDOW HALF SIZE WINDOWS THIRD SIZE WINDOWS QUAD SIZE WINDOWS

3.0 H x 3.0 W (76mm H x 76mm W)

1.5 H x 3.0 W (38mm H x 76mm W)

1.0 H x 3.0 W (25mm H x 76mm W)

0.75 H x 0.75 W (19mm H x 19 mm W)

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

ANNUNCIATOR MODEL CODE DEFINITION

SERIES 90A______ ______ SERIES 90A Model Number _____ _____ _____
Item 3 # of Cells Wide Item 4 Common Service

Item 1 Mounting Options

Item 2 # of Cells High

Item 5 Window Size

_____
Item 6 Active Points

_____

Item 7 Window Color

_____

Item 8 Operational Sequence

_____
Item 9 Repeat Relay

Item 10 Power Input

_____

Item 11 Field Contact Voltage

_____

Item 12 Window Legends

_____

Item 13 Comm. Options

_____

Item 14 Options

_____

Example: SERIES 90A -PM-3H-6W-INTB-2-34-W-AF-RR-B-X-TP-MB-TS-IB-RLY

Item 1 Mounting Options

PM PC RK S NCB NCT N4 N4PB Semi-Flush Panel Mounting Semi-Flush Panel Mounting w/rear cover 19 Rack Mounting (5 wide systems only) Surface (Wall) Mounting (1H to 5H x 2W to 5W) Weather-tight NEMA Front Cover w/ -20 Bolts Weather-tight NEMA Front Cover w/T Handle NEMA-4 Enclosure (1H to 6H x 3W to 8W) NEMA-4 Enclosure w/PB (1H to 6H x 3W to 8W)

Item 8 Operational Sequence

LN, AO, AONL, AF, AFNL, FR, AM, FRM, AS, ASFR, ASFRM, TFS, TFSFRM, TFSM, ARR, FRR, VS, VSRR, MC

IMO

Intermixed Sequences (up to 4 available)

Item 9 Repeat Relay Option

RR Auxiliary Repeat Relay Provided for every Input. (Can be field configured to follow: alarm input status, alarm sequence operation or Lamp Flash. Relays can be set for normally energized or de-energized operation and are jumper selectable for a Form A or Form B contact arrangement). FRC Auxiliary Repeat Relay Provided for every Input with Form C (SPDT) Contacts. (Can only be used with Window Size 1E or 2S). 2RR Two Repeat Relays for every input. (Selectable for a Form A or Form B contact arrangement. Can only be used with Window Size 1E or 2S.) NR No Repeat Relays required (Note: Can only choose one selection from above).

Item 2,3 Annunciator Size

# of Cells High (1-13)

# of Cells Wide (2-13)

Item 4 Common Service Cell (lower right cell)

INTB NPB Note: Integral Pushbuttons (ACK, SIL, TEST, RESET) Pushbuttons replaced w/ a Half or Full Size Window For either selection above, external pushbuttons can be connected to the Annunciator terminal blocks.

Item 5 Window Size

4 Quad Size, 4 inputs per cell, ea 1.5H x 1.5W 3 Third Size, 3 inputs per cell, ea 1.0H x 3.0W 2E Half Size, 2 inputs per cell, ea 1.5H x 3.0W 2S Half Size, 2 inputs per cell, ea 1.5H x 3.0W 2 Half Size, 2 inputs per cell, ea 1.5H x 3.0W 1E Full Size, 1 input per cell, ea 3.0Hx3.0W IMW Intermixed window size Note: Option 1E indicates that the cell is expandable up to 2 inputs. Option 2E indicates that the cell is expandable up to 4 inputs. Option 2S indicates one input module per single input provided. Do not include the CSM Cell in your quantity.

Item 10 Power Input

F E C B A 24 VDC 48 VDC 125 VDC 120 VAC, 60 HZ 230 VAC, 50 HZ

Item 11 Field Contact Voltage (FCV)

Field Contact Voltage internally supplied by AMETEK, with common system-wide FCV return. *For System Input Power Voltages of 120/230VAC or 125VDC. D 125 VDC FCV X 24 VDC FCV Field Contact Voltage externally supplied by Customer, internally bussed to all input modules. DC 125 VDC FCV supplied by Customer TC 48 VDC FCV supplied by Customer XC 24 VDC FCV supplied by Customer JC 12 VDC FCV supplied by Customer Field Contact Voltage externally supplied by Customer. Every input is isolated and requires a separate FCV connection. D/ISO 125 VDC FCV supplied by Customer T/ISO 48 VDC FCV supplied by Customer X/ISO 24 VDC FCV supplied by Customer J/ISO 12 VDC FCV supplied by Customer Y/ISO 120 VAC FCV supplied by Customer NR No Field Contact Voltage (Serial Input Only)

Item 6 Active Points

Total # of active points

Item 7 Window Color

W R A G Y B IMC White Window Filter Red Window Filter Amber Window Filter Green Window Filter Yellow Window Filter Blue Window Filter Intermix color, matrix must be included

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Item 12 Window Legends

TP Legends printed on Transparency Film (field changeable) E Legends Engraved on Windows Note: Window engraving or printed legends can be provided at the factory at no charge if provided 1 week before shipment.

Item 14 Options (continued)

SP Serial Printer used for Time Stamped Alarms (Used with SER option [time stamped alarms] and SD option [serial data output]. Modbus, DNP and Ethernet are not available when selecting this.) Ground Fault Detector (internally mounted) For 24, 48, 125VDC Field Contact Voltage (options X, D, XC, DC, TC) Additional Two CSM Common Relays (Base system includes 2 CSM Common Relays configurable for Critical or Non-Critical Horn, Ringback Horn. The additional 2 CSM Common Relays can be configured for additional horns or Critical/Non-Critical Reflash or Fault, Power Fail, System Watchdog, or Ground Fault Detect) External Inhibit Switch Input (Software configurable for inhibit of LED Lamps, Horn, Repeat Relay Outputs or CSM Common Relay Outputs) Internal Horn Automatic Horn Silence (Can be used to silence any horn with software configurable delay up to 60 seconds, in 0.25 second increments. Independent setting for internal or external horns) Flash Synchronization. Synchronizes the flash rate to remote displays. Needs to be specified for each Annunciator that will be synchronized together. (Requires wiring between Annunciator Systems.) CE Certification CE Certification available for all configurations except for FCV options D, DC, D/ISO, Y/ISO. In these cases, a NEMA Enclosure (option N4, N4PB) or Front Cover (option NCB, NCT) is required. 120/230VAC & 125VDC Input Power provided via External Supplies unless the NEMA Enclosure or Front Cover is used. Moisture/ Fungus Proof Coating FM Class 1, Div.2 Groups A,B,C,D Certification FM Certification available for all configurations. A NEMA Enclosure (option N4, N4PB) or Front Cover (option NCB, NCT) is required. Power option A (230Vac), B(120Vac), C(125Vdc), (see ITEM 10), is provided via External Supplies only.

Item 13 Serial Communications

SIM MB DNP SD NR Note: Modbus Serial Input Only (no Field Contact Inputs) Modbus Communications, Transmit or Receive DNP 3.0 Communications, Transmit Alarms Serial ASCII Data Output of Time Stamped Alarms (Used with the Time Stamping option SER only.) None of the above Serial communication options installed Can only select one of the above options. All options above are field selectable for RS-232 or RS-485 communications.

GF

RLY

Item 14 Options
ETH Ethernet Port (RJ-45 , T1 connection) SW (Used with Modbus or DNP Communication options. Must select option MB or DNP. Replaces RS232/485 Serial Port.) FR 1 msec Input Response (50 msec Standard) (This will capture alarms that last 1 msec or longer. If Time Stamping is required, select option SER instead) Time Stamping of alarms (4 ms resolution) (Each alarm is accompanied with a time stamp, containing point #, alarm state, time & date. The Time Stamp output can be selected as Serial ASCII Data to a printer or terminal [must select option SD], Modbus [must select option MB] or DNP [must select option DNP]. ) Time Stamping of alarms (1 ms resolution) (Each alarm is accompanied with a time stamp, containing point #, alarm state, time & date. The Time Stamp output can be selected as Serial ASCII Data to a printer or terminal [must select option SD], Modbus [must select option MB] or DNP [must select option DNP]. Option limited to 25 Cells) IRIG-B Time Sync Input (used with SER Option) (Standard BNC Input) STM FM HN AS

SER

FS

CE SERFR

IB

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

SYSTEM CONFIGURATION AND SET-UP

The SERIES 90A Annunciator is already factory configured per the model number. Most of the configuration of the system is made using software, however some settings such as relay contact arrangement (Form A or Form B) needs to be configured by the user. The default configurations are specified below: Item Inputs N.O. (normally open), N.C. (normally closed) Field Contact Inputs Field Contact Voltage (12, 24, 48, 125VDC, 120VAC) OR (24-125VDC) Common FCV (field contact voltage) or Isolated FCV Input Module Address Setting Operational Sequence (LN, AO, etc) Sequence Grouping Input Response Critical/Non-Critical Assignment Form A (normally open), Form B Contacts (normally closed) Form C Contacts (SPDT) Default Setting N.O. Factory Configured Per Model Number Configuration Method Software or Hardware * Hardware

Hardware Hardware Software Software Software Software Hardware Hardware

Optional Repeat Relays

1 group 50 msec Non-Critical Form A Factory Configured Per Model Number De-Energized Follows Input Form A De-Energized Critical Horn & Non-Critical Horn None Selected RS-232 Out Master

CSM Functions

Energized or De-Energized Relays Repeat Relay Operation Auxiliary Contact Output Type (Form A, Form B) Auxiliary Contact Output Mode (Energized or De-Energized) Auxiliary Contact Output Operation (Horn, Reflash, Fault, Watchdog, Power Monitor, Ground Fault) Other system-wide functions

Software Software Hardware Software Software

Software Hardware Hardware Hardware

Serial RS-232 , RS-485 Communication RS-485 Termination Jumper Module Flash Synchronization (master/slave)

* NO/NC Field Inputs can be configured via the software or hardware, but not both. Choose one method only.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

HARDWARE CONFIGURATION
Each Input/Output (I/O) module can accept up to two field contact inputs, with field contact voltage (FCV) provided either internally by the Annunciator or externally by the customer. Each input includes optical coupler isolation and can be selected for Normally Open (N/O) or Normally Closed (N/C) Field Contact Inputs through the software configuration or module jumpers. The I/O module provides outputs to the Display Module. Optional relays can be added to the I/O module for repeating the alarm status. Up to two I/O cards can be inserted into Card Slots 1 & 3 of a single cell for a maximum of 4 points per cell. The Cell with the Common Service Module can also support one I/O Module (in slot 3), in place of the Integral Pushbuttons. There are two versions of input modules. One version has headers and jumpers used to configure the FCV and the CSM address, while the other versions are designed with an input circuit capable of accepting an input range of 24vDC to 125vDC and use a rocker switch for the CSM Address. Both versions of the I/O module are configured via jumpers for: (NO/NC) and Form A, B, C Relay Contacts. Refer to the following table and to the part number affixed to the module to determine the type of module. Note that all modules in a systems shipped from the factory will contain the same type of configuration.

Table 1 Module Types

Description 3/4 PT I/O W/RELAY 1/2 PT I/O W/RELAY 1/2 PT I/O NO RELAY 3/4 PT I/O NO RELAY 1/2PT SER INPUT ONLY 1/2PT SER INPUT ONLY Header/jumper for FCV and CSM address Part Number 1085-250 1085-286 1085-287 1085-288 1085-304 1085-305 No FCV Jumpers required Switch for CSM address Part Number 1087-060 1087-241 1087-242 1087-243 1087-244 1087-245

Field Contact Type

The I/O module supports both N/O & N/C inputs through the software configuration, as detailed in the next section. N/O refers to Normally Open Field Contacts (open in Normal State, Closed in Alarm State) and N/C refers to Normally Closed Field Contacts (closed in Normal State, open in Alarm State) As an alternative, the N/O and N/C settings may be selected via jumper P5 & P6 on the I/O Module. NOTE: The NO/NC setting must only be configured via one method (hardware or software). It is recommended to use the software method to avoid any confusion.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Field Contact Voltage (FCV)

Refer to Table-1 Module Types above to determine the type of FCV configuration installed. I/O modules with the part number starting with 1085- supports Field Contact Voltages of 12, 24, 48, 125 through Jumper P1. The Field Contact Voltage may be selected as Common throughout the whole system or Isolated from input to input. This is selected via jumpers J1 & J2. I/O modules with the part number starting with 1087- supports Field Contact Voltages with a range of 24 through 125VDC with no need for configuration jumpers. The Field Contact Voltage may be selected as Common throughout the whole system or Isolated from input to input. This is selected via jumpers J1 & J2. NOTE: The Annunciator is already factory configured per the selections in the model number.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Repeat Relay Configuration Table Relay Operation Mode Repeat Relay Output Follows Input Contact State Relay Contact Status (shown in Normal State) OPEN OPEN (Form B) (Form A) Relay Coil Status (shown in Normal State) ENERGIZED DE-ENERGIZED ENERGIZED DE-ENERGIZED ENERGIZED DE-ENERGIZED ENERGIZED DE-ENERGIZED

CLOSED (Form A) CLOSED (Form B) Repeat Relay Output Latches on Alarm until Acknowledged or Reset OPEN OPEN (Form B) (Form A)

CLOSED (Form A) CLOSED (Form B)

NOTE: Option FRC uses a Form C output, which is a SPDT (Single Pole Double Throw) contact. Option 2RR indicates two Repeat Relays for a single alarm input. (used with 1E & 2S Window Sizes) Jumpers P2,3,4 are used to select Form A, B and C modes. The options for the Relay Operation Mode and Relay Coil Status (normally energized or de-energized relays) are selected using the software configuration tool. (Reference the instruction manual section for Software Configuration.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

CSM Address
Each I/O Module requires an address in order for communications to the CSM module. The Address settings are required for configuring any per point parameters and for mapping of serial communications. There are two versions of input modules using different methods of setting the address. Refer to Refer to Table-1 Module Types to determine which module is in your system. Older version
( Part numbers starting with 1085-)

The CSM address uses jumpers (J9) to indicate a binary address, starting at 0 and incrementing by one for every module in the system, from left to right, top to bottom. In cases where there is only one module per cell ( Window code 1E) the binary address will increment by two. Starting at 0 in the first cell, 2 in the second cell, 4 in the third cell etc. Zero is set when all jumpers are removed. Newer version
( Part numbers starting with 1087-)

The CSM address uses a rocker switch (SW1) to indicate a binary address, starting at 0 and incrementing by one for every module in the system, from left to right, top to bottom. In cases where there is only one module per cell ( Window code 1E) the binary address will increment by two. Starting at 0 in the first cell, 2 in the second cell, 4 in the third cell etc. Zero is set when all switches are set of off. NOTE: Care should be taken when removing and replacing I/O modules to insure that they are replaced into the cell from which they are removed. Failure to do so will result in out-of sequence address.

10

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

I/O Module Configuration

(1085-xxx modules containing FCV jumpers)

P1 FCV Selection

J1, 2 Isolated/Common FCV

P5, 6 NO / NC Inputs

J9 Address Selection
(Configured at Factory)

P2, 3, 4 Relay Output Jumpers

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

11

I/O Module Configuration

(1087-xxx modules with auto range FCV)

J1, 2 Isolated/Common FCV

C17
VR2 R23

C7

R7

Q2

R1

D5
RF1

1
R25

1
L1 RV1 L2

R2
RV3

R4 Q3 R8

C19

R3

P5, 6 NO / NC Inputs

1
C15 C16

R22

R52

R24

U7

R26

J2 D4 D6

J1

RV2 RF4

J8
R51
U10 R42

J6 1
C14
C23

L3

P13
2 R46 R44

D2

J7

C20

K1

CR1

C21

VR1

F1 P11

R41 R40 U1

Q1
C24

R32

R47 U2 R45 R48 R49 R35

R34

R39 C25

U3

D1
C13

1 P2

P4 1

CR2 R38 C22 R31 R30 C11 RN1

R36 C26 R37

P12 1 U9 P3
R50

1 K2
R16

RF2

P5 U6

P6 U8 1

C6

D3

SW1 Address Selection

0 1 2 3 4 5 6

C27 +

U11

R43

J4

C18

C8

P2, 3, 4 Relay Output Jumpers

R10 R11

U4
R20 7 R14 C12
C10

C3 C2 R13 C5 RF3 C4 C1

R15 R19

U5
R33

R29

R17 R18

R12 R9

0 1 2 3 4 5 6 7

SW1
C9

1 J5

R21

J3

MSB Spare

LSB

J1,J2: INPUT ISOLATION SELECTION SW1 ADDRESS SELECTION ISOLATED INPUTS J2 J1

COMMON INPUTS WITH FCV J2 J1

P5,P6: INPUT NORMALLY OPEN (NO)/NORMALLY CLOSED (NC) P5 NO NC P6

P2,P3,P4: RELAY OUTPUT SELECTION FORM A (N.O.) RELAY #1: P2 P3 P4 FORM B (N.C.) P2 P3 P4 FORM C (SPDT) P2 N/A P4

RELAY #2:

12

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Display Module
The Display Module provides the LED indication for up to 4 window sizes (Full Size, Half, Third and Quad). Each display module plugs into one or two I/O cards, depending on the window size and input quantities. There are several variations of display modules as noted by the window size in the model number: Version
1 2 3 4

Window Size, Configuration

1E, 2 2S, 2E, 4 3 1E, 2 (in CSM Cell)

There is no setup required for these modules. (Factory configured)

4 Point and all options shown for reference Not all configurations have all of the displayed components.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

13

Common Service Modules

The Common Service Module (CSM) is typically located in the lower right cell of the Annunciator System in card slot 1. It is used to provide common alarm outputs, perform flashing per selectable ISA Sequences and coordinate the pushbutton controls. One version CSM includes the Time Stamping of Alarms or Sequential Events Recorder (SER). The CSM has four common alarm outputs (2 standard and 2 optional) with relay operation configured via Software. All Annunciator software configuration is performed through the CSM serial port, accessible from the front of unit. The CSM module can be configured via jumpers for Form A or B Relay Contacts.

Relay output selection ( LK1-4)

14

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Communication Modules
The optional Communication Modules plug directly into the CSM Module through card slot 2 and provide either a serial or Ethernet output. Only one Communication Module per CSM is allowed.

Serial
The Serial Communication Module provides RS-232/485 serial data output or inputs via Modbus or DNP protocols. When used with the SER CSM, it can be used to provide an output of time stamped alarms in ASCII format in addition to Modbus or DNP. The Serial Communication Module can be configured via jumpers for RS-232/485 communications. It can be configured via software for all Modbus and DNP settings.
RS-485 TERMINATOR J2 RS-232/RS-485 SELECTION J5 RS-232 RS-485

FLASH SYNC U8, U9 MASTER - J8 IN, J9 OUT SLAVE - J8 OUT, J9 IN

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

15

Ethernet
The Ethernet Communication Module has no configuration jumpers. When installed this module is mounted onto the Common Service module and together they are installed in slot 1 and 2,

16

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Ground Fault Detector Module

The optional Ground Fault Detector Module can be installed in Card Slot 5 of any cell that does not contain an Integral Power Supply or IRIG-B Module. It can be calibrated for sensitivity via the front. The Ground Fault Detector has jumpers selectable for the Field Contact Voltage used within the system. It only operates with 24, 48 or 125VDC.

24V

48V

125V

FCV Voltage Jumper Settings P1

Power Supply Modules

Several Integral Power Supply Modules are available depending on the system input power, size of the system and field contact voltage selection. There are no configurable jumpers on these modules. Refer to the power connection in this manual for the power supply images.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

17

Field Contact Voltage Supply Modules

Several Integral FCV Supply Modules are available depending on the system input power and field contact voltage selection. There are no configurable jumpers on these modules. Refer to the power connection in this manual for the power supply images.

IRIG-B Module
The optional IRIG-B Module is used for External time synchronization of the SER Option. This must be installed in Card Slot 5 of the CSM Cell. (When used, the Integral Power Supply must be moved to a different cell.)

JP1, JP2
AC/DC 1 2 3

IRIG-B MODULE SETUP

Jumper Position
JP1 JP2 JP1 JP2 1 1 1 1 2 2 2 2 3 3 3 3

INPUT TYPE
Modulated(AC) Demodulated (DC)

18

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

INSTALLATION
MOUNTING
The system is designed for Panel Mounting and 19 Rack Mounting, Other mounting methods such as NEMA Enclosures and Surface or Wall Mounting will have additional details and drawings provided by the factory. Caution must be exercised when installing this, or any other type of equipment into racks or panels. Ensure that all equipment is properly secured using the specified hardware in accordance with equipment manufacturers specifications.

Panel Mounting (option PM, PC)

Panel Mount Bracket
Qty provided and location dependant on system size

The dimensions given in the tables below refer to the size of the panel cut out required for mounting and the front bezel height and width. The height and width are related to the number of cells in the system. Dimensions shown are in inches (mm).
# of Cells High
1 2 3 4 5 6 7 8 9 10 11

# of Cells Wide
--2 3 4 5 6 7 8 9 10 11

Overall Height or Overall Width

5.0 (127) 8.47 (215) 11.94 (303) 15.40 (391) 18.88 (479) 22.34 (568) 25.81 (656) 29.28 (744) 32.75 (832) 36.22 (920) 39.69 1008)

Panel Cut-Out Height or Panel Cut-Out Width

4.06 (103) 7.53 (191) 11.0 (279) 14.47 (368) 17.94 (456) 21.41 (544) 24.88 (632) 28.34 (720) 31.81 (808) 35.28 (896) 38.75 (984)

Tolerance on all cut out dimensions is 0.0625 inches (1.5mm)

12
13

12
13

43.16 (1096)
46.63 (1184)

42.22 (1072)
45.69 (1161)
19

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Example: A 3H x 4W Annunciator has a cutout height of 11.0 and a cutout width of 14.47. Annunciator Depth (Behind Panel) Maximum depth w/out rear cover Maximum depth w/ rear cover Inches 6.75 10.00 Mm 171 254

Minimum mounting panel thickness: 18 GA Galvanneal, 0.072 inches, 1.83 mm. For system installation perform the following steps: 1 Mark cutout dimensions on the surface where the annunciator is to be mounted, keeping in mind that the assembly may rest on the sill of the cutout. NOTE: Allow a minimum of 6 inches (150 mm) above the unit and behind the panel for proper ventilation. 2 3 Cut out and remove panel material. Temporally remove the panel mounting clamps and Install the annunciator assembly through the panel cut-out (from the front of the panel). Position the annunciator within the cut-out so that the weight is taken at the bottom of the unit. From the rear of the panel, replace the annunciator mounting clamps along the bottom then top and sides screws to finger tight check the front of panel alignment on panel face etc Fully tighten the mounting clamps.

20

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

19 Rack Mounting (option RK)

The dimensions given in the tables below refer to the height of the 19 Rack based on the number of Cells High. In all configurations, the Annunciator will be 5 cells wide to maintain the 19 rack width. Dimensions shown are in inches (mm)
# of Cells High 1 2 3 4 5 6 7 8 9 10 11 12 13 Annunciator Depth Maximum depth Overall Rack Height Inches mm 5.25 133.35 8.75 222.25 12.25 311.15 15.75 400.05 19.25 488.95 22 75 577.85 26.25 666.75 29.75 755.65 33.25 844.55 36.75 933.45 40.25 1022.35 43.75 1111.25 47.25 1200.15 Inches 6.8 U Rack 3U 5U 7U 9U 11U 13U 15U 17U 19U 21U 23U 25U 27U mm 172.72

For system installation, perform the following steps: Allow a minimum of 6 inches (150 mm) above the unit and behind the panel for proper ventilation. 1 Slide the annunciator assembly into the rack (from the front of the rack). 2 Secure using the recommended fixing screws into the rack mount rails.
SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL 21

NEMA Enclosure (option N4, N4PB)

The dimensions given in the chart below are for both options (N4, N4PB). Only the N4 is shown. Both options may also include a horn mounted on the face of the door. The Annunciator is mounted on a swing frame behind the door and is viewed through a window installed in the door. The swing frame allows access to the wiring behind the Annunciator. Caution: In order to prevent tipping, the NEMA enclosure must be securely fastened to a surface before attempting to open the door or the swing panel.
'G' 'H'

Window in door for viewing Annunciator

'F' 'A'

Side view

'E'
Optional Horn, Not available on all sizes)

10.00

'B'

Bottom View Gland Plate Opening

'K'

1.50
'J'
PART # 1 or 2 H X 3 or 4W 1 or 2 H X 5 or 6W 1 or 2 H X 7 or 8W 3 or 4 H X 3 or 4W 3 or 4 H X 5 or 6W 3 or 4 H X 7 or 8W 5 or 6 H X 3 or 4W 5 or 6H X 5 or 6W 5 or 6H X 7 or 8W

16.00 22.00 16.00 30.00 16.00 36.00 24.00 22.00 24.00 30.00 24.00 36.00 32.00 22.00 32.00 30.00 32.00 36.00

6.03 7.32 6.03 7.32 5.63 7.32

3.25 14.25 12.13 4.63 4.31 21.19 12.13 4.63

3.47 28.03 19.63 4.63

7.09 14.25 3.25 14.25 12.13 4.63 7.09 14.25 4.31 21.19 12.13 4.63

6.75 14.25 3.47 28.03 19.63 4.63 8.15 21.19 8.15 21.19 7.75 21.19 3.25 14.25 12.13 4.63 4.31 21.19 12.13 4.63

3.47 28.03 19.63 4.63

22

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Surface (Wall) Mounting (option S)

Mounting to a wall or other surface. The annunciator is hinged on one side to allow access to the terminal blocks in the rear of the unit. The hinge may be moved to the right side of the annunciator by removing the brackets, rotating them and re mounting them to the opposites side(s). Refer to table for available sizes and dimensions. All mounting holes sized for -20 hardware. A minimum of 10 of swing clearance is required on the hinge side of the annuncator. Hinge side

Refer to the following chart and the figures on the following page for mounting dimensions. ANNUNCIATOR SIZE Dimension
A B C D E F G H 1H 3.65 4.93 0.40 1.90 ------------------2.23 2H 7.12 8.40 1.12 4.59 ------------------5.70 3H 10.59 11.87 1.12 4.59 8.05 ------------9.17 4H 14.06 15.34 1.12 4.59 8.05 11.52 12.64 5H 17.53 18.81 1.12 4.59 8.05 11.52 14.99 16.11 2W 3W 4W 5W

Dimension

8.74 8.39 10.24

12.21 11.86 13.71

15.68 15.33 17.18

19.15 18.80 20.65

J K L

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

23

1.620

1.620

G F E D

9.93 8.87

#6-32 x 3/4 FLATHEAD SCREW

1.5

Right side

#6 HEX KEPS NUT

#6 HEX KEPS NUT #6 CUP WASHER #6 HEX KEPS NUT

Hinge side view

#6 CUP WASHER

24

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Weather Tight NEMA Front Cover (option NCB, NCT)

This option provides for a NEMA rated front cover for the panel-mounted option, it consists of a swing frame and a weather tight door. Two options are available; the NCB option uses bolts to secure the door to the panel; the NCT option has a T-Handle for securing the door. Both options use -20 mounting bolts to secure the swing panel to the mounting surface. Refer to the charts following for the mounting hole location and over-all size of the door. Refer to the Panel mount option for the cut-out dimensions for the annunciator, mount the door option, centered on the hole. Mount the annunciator thru the panel hole and secure with the mounting clamps as described in the panel mount installation instructions (option PM, PC)

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

25

.50 TYP

.281 DIA (4 HOLES)

.50

2.19 TYP

Cutout for mounting Annunciator

clips shown for NCB option Only one clip, centered, for NCT option

2.19 TYP .50

F
D

# OF CELLS HIGH 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3

# OF CELLS WIDE 2 3 4 5 6 7 8 9 10 2 3 4 5 6 7 8 9 10 2 3 4 5 6 7 8 9 10

DIM A 8.38 8.38 8.38 8.38 8.38 8.38 8.38 8.38 8.38 11.84 11.84 11.84 11.84 11.84 11.84 11.84 11.84 11.84 15.31 15.31 15.31 15.31 15.31 15.31 15.31 15.31 15.31

DIM B 11.84 15.31 18.78 22.25 25.72 29.19 32.66 36.13 39.59 11.84 15.31 18.78 22.25 25.72 29.19 32.66 36.13 39.59 11.84 15.31 18.78 22.25 25.72 29.19 32.66 36.13 39.59

DIM C 7.38 7.38 7.38 7.38 7.38 7.38 7.38 7.38 7.38 10.84 10.84 10.84 10.84 10.84 10.84 10.84 10.84 10.84 14.31 14.31 14.31 14.31 14.31 14.31 14.31 14.31 14.31

DIM D 10.84 14.31 17.78 21.25 24.72 28.19 31.66 35.13 38.59 10.84 14.31 17.78 21.25 24.72 28.19 31.66 35.13 38.59 10.84 14.31 17.78 21.25 24.72 28.19 31.66 35.13 38.59

DIM E 4.00 4.00 4.00 4.00 4.00 4.00 4.00 4.00 4.00 7.47 7.47 7.47 7.47 7.47 7.47 7.47 7.47 7.47 10.94 10.94 10.94 10.94 10.94 10.94 10.94 10.94 10.94

DIM F 7.47 10.94 14.41 17.88 21.34 24.81 28.28 31.75 35.22 7.47 10.94 14.41 17.88 21.34 24.81 28.28 31.75 35.22 7.47 10.94 14.41 17.88 21.34 24.81 28.28 31.75 35.22

26

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

# OF CELLS HIGH 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 7 7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8 8 9 9 9 9 9 9 9 9

# OF CELLS WIDE 2 3 4 5 6 7 8 9 10 2 3 4 5 6 7 8 9 10 2 3 4 5 6 7 8 9 10 2 3 4 5 6 7 8 9 10 2 3 4 5 6 7 8 9 10 2 3 4 5 6 7 8 9

DIM A 18.78 18.78 18.78 18.78 18.78 18.78 18.78 18.78 18.78 22.25 22.25 22.25 22.25 22.25 22.25 22.25 22.25 22.25 25.72 25.72 25.72 25.72 25.72 25.72 25.72 25.72 25.72 29.19 29.19 29.19 29.19 29.19 29.19 29.19 29.19 29.19 32.66 32.66 32.66 32.66 32.66 32.66 32.66 32.66 32.66 36.13 36.13 36.13 36.13 36.13 36.13 36.13 36.13

DIM B 11.84 15.31 18.78 22.25 25.72 29.19 32.66 36.13 39.59 11.84 15.31 18.78 22.25 25.72 29.19 32.66 36.13 39.59 11.84 15.31 18.78 22.25 25.72 29.19 32.66 36.13 39.59 11.84 15.31 18.78 22.25 25.72 29.19 32.66 36.13 39.59 11.84 15.31 18.78 22.25 25.72 29.19 32.66 36.13 39.59 11.84 15.31 18.78 22.25 25.72 29.19 32.66 36.13

DIM C 17.78 17.78 17.78 17.78 17.78 17.78 17.78 17.78 17.78 21.25 21.25 21.25 21.25 21.25 21.25 21.25 21.25 21.25 24.72 24.72 24.72 24.72 24.72 24.72 24.72 24.72 24.72 28.19 28.19 28.19 28.19 28.19 28.19 28.19 28.19 28.19 31.66 31.66 31.66 31.66 31.66 31.66 31.66 31.66 31.66 35.13 35.13 35.13 35.13 35.13 35.13 35.13 35.13

DIM D 10.84 14.31 17.78 21.25 24.72 28.19 31.66 35.13 38.59 10.84 14.31 17.78 21.25 24.72 28.19 31.66 35.13 38.59 10.84 14.31 17.78 21.25 24.72 28.19 31.66 35.13 38.59 10.84 14.31 17.78 21.25 24.72 28.19 31.66 35.13 38.59 10.84 14.31 17.78 21.25 24.72 28.19 31.66 35.13 38.59 10.84 14.31 17.78 21.25 24.72 28.19 31.66 35.13

DIM E 14.41 14.41 14.41 14.41 14.41 14.41 14.41 14.41 14.41 17.88 17.88 17.88 17.88 17.88 17.88 17.88 17.88 17.88 21.34 21.34 21.34 21.34 21.34 21.34 21.34 21.34 21.34 24.81 24.81 24.81 24.81 24.81 24.81 24.81 24.81 24.81 28.28 28.28 28.28 28.28 28.28 28.28 28.28 28.28 28.28 31.75 31.75 31.75 31.75 31.75 31.75 31.75 31.75

DIM F 7.47 10.94 14.41 17.88 21.34 24.81 28.28 31.75 35.22 7.47 10.94 14.41 17.88 21.34 24.81 28.28 31.75 35.22 7.47 10.94 14.41 17.88 21.34 24.81 28.28 31.75 35.22 7.47 10.94 14.41 17.88 21.34 24.81 28.28 31.75 35.22 7.47 10.94 14.41 17.88 21.34 24.81 28.28 31.75 35.22 7.47 10.94 14.41 17.88 21.34 24.81 28.28 31.75
27

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

# OF CELLS HIGH 9 10 10 10 10 10 10 10 10 10

# OF CELLS WIDE 10 2 3 4 5 6 7 8 9 10

DIM A 36.13 102 39.59 39.59 39.59 39.59 39.59 39.59 39.59 39.59

DIM B 39.59 102 15.31 18.78 22.25 25.72 29.19 32.66 36.13 39.59

DIM C 35.13 102 38.59 38.59 38.59 38.59 38.59 38.59 38.59 38.59

DIM D 38.59 102 14.31 17.78 21.25 24.72 28.19 31.66 35.13 38.59

DIM E 31.75 102 35.22 35.22 35.22 35.22 35.22 35.22 35.22 35.22

DIM F 35.22 102 10.94 14.41 17.88 21.34 24.81 28.28 31.75 35.22

28

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

External Power Supply Mounting

An external Power Supply is available for 120/230VAC Power and one is available for 125VDC Power also. These are used on larger systems per the power supply chart.

120/230VAC Power Supply

125VDC Power Supply

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

29

WIRING
All wiring connections are made to the rear of the unit using barrier style terminal blocks. All Field Contact Inputs, Relay Outputs and Power Connections are made to Terminal Blocks that have a #6 screw, which will accept a solid or stranded wire from 12-22 AWG, with or without ring & spade lugs. The Pushbutton Controls and Flash Synchronization connections are made to Terminal Blocks that have a #6 screw which will accept a solid or stranded wire from 14-22 AWG, with or without ring & spade lugs. Ensure that a proper earth ground connection is made to the protective earth ground stud.

Note for Relay Output Wiring: When option RR (Repeat relay) is installed, and 120 Vac is switched by the contact. All output wiring in any individual cell must be wired to the same phase of the service.

Input Wiring
The input wiring is determined by the number of alarms (or windows per cell) and the number of I/O Cards. The available configurations are:
FULL SIZE WINDOW
(1 MODULE)

HALF SIZE WINDOWS

(1 OR 2 MODULES)

THIRD SIZE WINDOWS

(2 MODULES)

QUAD SIZE WINDOWS (2 MODULES)

1 1 2

1 2 3

1 3

2 4

3.0 H x 3.0 W (76mm H x 76mm W)

1.5 H x 3.0 W (38mm H x 76mm W)

1.0 H x 3.0 W (25mm H x 76mm W)

0.75 H x 0.75 W (19mm H x 19 mm W)

The I/O cards can support up to two inputs, however, certain options limit that to one input per card as shown with the Half Size Window above.

Common Field Contact Voltage

The I/O cards are typically set up for a common system-wide Field Contact Voltage (FCV). In this case, terminals 2 and 4 of each I/O Terminal Block are connected to the FCV, which is internally bussed throughout the system to the Power Supply Terminal Block, Terminal 3. As shown in the Power Supply Drawings, an external Field Contact Voltage Supply can be connected to the Power Supply Terminal Block for distribution throughout the system. In systems where the FCV is generated within the Annunciator, it is already distributed throughout the Annunciator. Each I/O card FCV connection is internally fused preventing any overload from the field. Removing an I/O card will disconnect the FCV at the terminal block for that card only.
30 SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Isolated Field Contact Voltage

The I/O cards can be jumpered to remove the system wide bussing and replace with an individual FCV connection per input. This is shown on the drawings as well.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

31

Input / Relay Wiring for Full Size Windows

(using one I/O Card)

Model Code Window Size 1E

TB5
1

TB1
1 2 3 4 5 6 7 8

Power Supply Terminal Block (only used with Integral Power Supplies)

2 3 4 5

Input/Relay Terminal Block

(Front View)

I/O Terminal Ass'y (Rear View)

INPUT WIRING Common FCV

TB1
Input 1 + FCV + FCV is internally bussed throughout the system to all TB1 Terminal Blocks.
1 2 3 4 5 6 7 8

Customer Field Contact

INPUT WIRING Isolated FCV

TB1
Input 1 - FCV
1 2 3 4 5 6 7 8

+(L) -(N)

24,48,125 VDC 120VAC, 60Hz Customer FCV

REPEAT RELAY WIRING

Option RR and 2RR

REPEAT RELAY WIRING

Option FRC

TB1
Input 1 + FCV
1 2 3 4

TB1
Input 1 - FCV
1 2 3 4

Option RR Single Repeat Relay Per Input (Form A or B) Option 2RR Two Repeat Relays Per Input (Form A or B)

5 6 7 8

Repeat Relay for Input #1 Repeat Relay for Input #1

Option FRC Single Repeat Relay Per Input (Form C)

5 6 7 8

Repeat Relay for Input #1

32

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Input/Relay Wiring For Half Size Windows (using one I/O Card)
Model Code Window Size 2
TB5
1

TB1
1 2 3 4 5 6 7 8

Power Supply Terminal Block (only used with Integral Power Supplies)

2 3 4 5

Input/Relay Terminal Block

(Front View)

I/O Terminal Ass'y (Rear View)

INPUT WIRING
Common FCV
TB1
Input 1
+ FCV 1 2 3 4 5 6 7 8 Customer Field Contact

INPUT WIRING
Isolated FCV
TB1
Input 1 - FCV Input 2 - FCV
1 2 3 4 5 6 7 8 +(L) -(N) +(L) -(N)

24,48,125 VDC 120VAC, 60Hz Customer FCV 24,48,125 VDC 120VAC, 60Hz Customer FCV

Input 2
+ FCV

+ FCV is internally bussed throughout the system to all TB1 Terminal Blocks.

REPEAT RELAY WIRING

Option RR

TB1
Input 1 + FCV
1 2 3 4 5

Option RR Single Repeat Relay Per Input (Form A or B)

6 7 8

Repeat Relay for Input #1 Repeat Relay for Input #2

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

33

Input/Relay Wiring For Half Size Windows (using one I/O Card)
Model Code Window Size 2E
TB5 TB2
1 1 2 3 4 5 6 7 8

TB1
1 2 3 4 5 6 7 8
Terminal Block TB2. No connections. E Option: Used for expanding up to 4

Power Supply Terminal Block (only used with Integral Power Supplies)

2 3 4 5

Input/Relay

(Front View)

I/O Terminal Ass'y (Rear View)

INPUT WIRING
Common FCV
TB1
Input 1
+ FCV 1 2 3 4 5 6 7 8 Customer Field Contact

INPUT WIRING
Isolated FCV
TB1
Input 1 - FCV Input 2 - FCV
1 2 3 4 5 6 7 8 +(L) -(N) +(L) -(N)

24,48,125 VDC 120VAC, 60Hz Customer FCV 24,48,125 VDC 120VAC, 60Hz Customer FCV

Input 2
+ FCV

+ FCV is internally bussed throughout the system to all TB1 Terminal Blocks.

REPEAT RELAY WIRING

Option RR

TB1
Input 1 + FCV
1 2 3 4 5

Option RR Single Repeat Relay Per Input (Form A or B)

6 7 8

Repeat Relay for Input #1 Repeat Relay for Input #2

34

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Input Wiring with Half Size Windows

Model Code Window Size 2S
TB5 TB2
1 1 2 3 4 5 6 7 8

TB1
1 2 3 4 5 6 7 8

Power Supply Terminal Block (only used with Integral Power Supplies)

2 3 4 5

Input/Relay Terminal Block TB1, TB2

(Front View)

INPUT WIRING
Common FCV
TB2
Input 2 + FCV
1 2 3 4 5 6 7 8

I/O Terminal Ass'y (Rear View)

Customer Field Contact Input 1 + FCV

TB1
1 2 3 4 5 6 7

Customer Field Contact

INPUT WIRING
Isolated FCV
Customer Field Contact +(L) -(N) 24,48,125 VDC 120VAC, 60Hz Customer FCV Input 1 - FCV

8 Customer

Field Contact

TB2
Input 2 - FCV
1 2 3 4 5 6 7 8

TB1
1 2 3 4 5 6 7 8

+(L) -(N)

24,48,125 VDC 120VAC, 60Hz Customer FCV

(using two I/O Cards)

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

35

Repeat Relay Wiring for Half Size Windows (using two I/O Cards)

Model Code Window Size 2S REPEAT RELAY WIRING

TB5 TB2
1 1 2 3 4 5 6 7 8

TB1
1 2 3 4 5 6 7 8

Power Supply Terminal Block

2 3 4 5

(only used with Integral Power

Supplies)

Input/Relay Terminal Block TB1, TB2

(Front View)

I/O Terminal Ass'y (Rear View)

TB2
Input 2 FCV
1 2 3 4

Option RR and 2RR

Input 1 FCV

TB1
1 2 3 4

Option RR Single Repeat Relay Per Input (Form A or B) Option 2RR Two Repeat Relays Per Input (Form A or B)

5 6 7 8

Repeat Relay for Input #2 Repeat Relay for Input #2

Option RR Single Repeat Relay Per Input (Form A or B) Option 2RR Two Repeat Relays Per Input (Form A or B)

5 6 7 8

Repeat Relay for Input #1 Repeat Relay for Input #1

TB2
1 2 3 4 5 6 7 8

TB1

Option FRC

Input 1 FCV

1 2 3 4 5

Repeat Relay for Input #2

Option FRC Single Repeat Relay Per Input (Form C)

6 7 8

Repeat Relay for Input #1

36

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Input/Relay Wiring for Third Size Windows (using two I/O Cards)

Model Code Window Size 3

TB2
1 2 3 4 5 6 7 8

TB1
1 2 3 4 5 6 7 8

Input/Relay Terminal Block

(Front View)

I/O Terminal Ass'y (Rear View)

INPUT WIRING
Common FCV
TB2
Input 3 + FCV + FCV is internally bussed throughout the system to all TB1-2 Terminal Blocks. (reference power supply wiring for main FCV connections)
1 2 3 4 5 6 7 8 Customer Field Contact

TB1
Input 1 + FCV Input 2 + FCV
1 2 3 4 5 6 7 8

Customer Field Contact

INPUT WIRING
Isolated FCV
TB2
Input 3 - FCV
1 2 3 4 5 6 7 8

Customer Field Contact +(L) -(N) 12, 24, 48, 125 VDC 120VAC, 60Hz Customer FCV Input 1 - FCV Input 2 - FCV

TB1
1 2 3 4 5 6 7 8

Customer Field Contact +(L) -(N) +(L) -(N) 12,24,48,125 VDC 120VAC, 60Hz Customer FCV 12,24,48,125 VDC 120VAC, 60Hz Customer FCV

REPEAT RELAY WIRING

Option RR
TB2
Input 3 - FCV
1 2 3 4 Option RR Single Repeat Relay Per Input (Form A or B) 5 6 7 8

TB1
Input 1 - FCV Input 2 - FCV Option RR Single Repeat Relay Per Input (Form A or B) Option RR Single Repeat Relay Per Input (Form A or B)
1 2 3 4 5 6 7 8

Repeat Relay for Input #3

Repeat Relay for Input #1 Repeat Relay for Input #2

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

37

Input/Relay Wiring for Quad Size Windows

(using two I/O Cards)

Model Code Window Size 4

TB2
1 2 3 4 5 6 7 8

TB1
1 2 3 4 5 6 7 8

Input/Relay Terminal Block

(Front View)

I/O Terminal Ass'y (Rear View)

INPUT WIRING
Common FCV
TB2
Input 3 + FCV Input 4
+ FCV 1 2 3 4 5 6 7 8

Customer Field Contact Input 1 + FCV Input 2 + FCV

TB1
1 2 3 4 5 6 7 8

Customer Field Contact

+ FCV is internally bussed throughout the system to all TB1-2 Terminal Blocks. (reference power supply wiring for main FCV connections)

INPUT WIRING
Isolated FCV
TB2
Input 3 - FCV Input 4 - FCV
1 2 3 4 5 6 7 8

Customer Field Contact +(L) -(N) +(L) -(N) 12,24,48,125 VDC 120VAC, 60Hz Customer FCV 12,24,48,125 VDC 120VAC, 60Hz Customer FCV Input 1 - FCV Input 2 - FCV

Customer

TB1
1 2 3 4 5 6 7 8

Field Contact +(L) -(N) +(L) -(N)

12,24,48,125 VDC 120VAC, 60Hz Customer FCV 12,24,48,125 VDC 120VAC, 60Hz Customer FCV

TB2
Input 3 - FCV Input 4 - FCV 1 2 3 4 5 6 7 8

REPEAT RELAY WIRING

Option RR
Input 1 - FCV Input 2 - FCV Option RR Single Repeat Relay Per Input (Form A or B) Option RR Single Repeat Relay Per Input (Form A or B)

TB1
1 2 3 4 5 6 7 8

Option RR Single Repeat Relay Per Input (Form A or B) Option RR Single Repeat Relay Per Input (Form A or B)

Repeat Relay for Input #3 Repeat Relay for Input #4

Repeat Relay for Input #1 Repeat Relay for Input #2

38

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Common Service Cell Wiring (with Integral Pushbuttons)

Model Code INTB Integral Pushbuttons
Terminal Block Power Supply (only used with Integral Power Supplies) Pushbutton/Switch Terminal Block TB4 CSM Relay Terminal Block TB3

TB5
1 2 3 4 5 J2 J1

TB4
1 2 3 4 5 6 7

TB3
1 2 3 4 5 6 7 8

SIL

ACK

TEST

RESET
J3

SYSTEM STATUS

FAIL

REMOTE COMM

GROUND FAULT

(front view)

CSM Terminal Block Assembly

(rear view)

CSM WIRING
Common Service Relay Wiring
TB3
CSM Relay #1 (Form A or B) CSM Relay #2 (Form A or B) CSM Relay #3 (Form A or B) CSm Relay #4 (Form A or B)
1 2 3 4 5 6 7 8

Pushbutton / Switch Wiring

TB4
CSM Relay K1 Common Return Silence Acknowledge Test CSM Relay K3 CSM Relay K4 Reset Configurable Input (option SW) + LED Flash Synchronization - LED Flash Synchronization
1 2 3 4 5 6 7 8

Customer Pushbuttons

CSM Relay K2

Option RLY

To other Annunciator + LED Sync To other Annunciator - LED Sync

Note: TB4-7 can be used as a second Configurable Input when the LED Flash Synchronization Option is not used.

Power Supply Wiring

TB5
Power +(L) Input -(N) FCV Input
1 2 3 4 5

Communications Wiring RS-232

RS-485
TX/RX TX/RX + Ground

Customer Power Input 24, 48 125 VDC 120/240 VAC, 50/60HZ Field Contact Voltage (FCV) 24, 48, 125 VDC 120 VAC, 60HZ (no connection required if the FVC is supplied through the Intergral Power Supply)

+ E

DB9 (F) Connector J1

1 2 3 4 5 6 7 8 9

Transmit Receive Ground RTS

BNC Connector

RJ 45 Connector
J3

J2

IRIG-B

Ethernet

NOTE: When wiring an external horn or other audible device to the CSM output relays, it is recommended that the interconnect wires be physically isolated from any other input or output wiring.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

39

Common Service Wiring (with I/O Modules)

FULL SIZE WINDOW

Model Code NPB

HALF SIZE WINDOWS (1 I/O Card)

(1 I/O Card)

OR

Pushbutton/Switch Terminal Block TB4 Input Terminal Block TB1

TB1
1 2 3 4 5 J1 6 7 8 J2

TB4
1 2 3 4 5 6 7 8

TB3
1 2 3 4 5 6 7 8

CSM Relay Terminal Block TB3

CSM Terminal Block Assembly

Common Service Relay Wiring

TB3
CSM Relay #1 (Form A or B) CSM Relay #2 (Form A or B) CSM Relay #3 (Form A or B) CSm Relay #4 (Form A or B)
1 2 3 4 5 6 7 8

(rear view)

Pushbutton / Switch Wiring

TB4
CSM Relay K1 Common Return Silence Acknowledge Test CSM Relay K3 CSM Relay K4 Reset
(option SW) + LED Flash Synchronization - LED Flash Synchronization

1 2 3 4 5 6 7 8

Customer Pushbuttons

CSM Relay K2

Option RLY

Configurable Input

To other Annunciator + LED Sync To other Annunciator - LED Sync

Note: TB4-7 can be used as a second Configurable Input when the LED Flash Synchronization Option is not used.

Input / Relay Wiring

TB1
Input 1 + FCV Input 2 - FCV Option RR Single Repeat Relay Per Input (Form A or B) Option RR Single Repeat Relay Per Input (Form A or B)
1 2 3 4 5 6 7 8

Communications Wiring
RS-232 RS-485
TX/RX TX/RX + Ground

Shown w/common FCV +(L) -(N)

Connector DB9 (F) Shown w/Isolated FCV 24,48,125 VDC J1 120VAC, 60Hz
Customer FCV

Repeat Relay for Input #1 Repeat Relay for Input #2

1 2 3 4 5 6 7 8 9

Transmit Receive Ground RTS

RJ 45 Connector

J2

Ethernet

NOTE: When wiring an external horn or other audible device to the CSM output relays, it is recommended that the interconnect wires be physically isolated from any other input or output wiring.
40 SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

CONNECTING POWER
The SERIES 90A Annunciator operates from a selection of AC and DC Voltages. The Annunciator uses Power Supplies to provide the necessary 5VDC Logic and LED Power. If the Field Contact Voltage (FCV) needs to be provided from the Annunciator, separate FCV Supplies are provided. For 24 and 48 VDC Input Power, an Integral Power Supply will always be used. In some cases, multiple supplies will be located in the system to accommodate the quantity of inputs specified. For 120/230 VAC and 125 VDC Input Power, the quantity of inputs, window sizes and other options determines whether the Power supplies can be self contained within the Annunciator (Integral Power Supply) or external to the Annunciator.

120/230 VAC & 125VDC Input Power

Annunciator Window Size Full Half Third Quad (1 per Cell) (2 per Cell) (3 per Cell) (4 per Cell) Integral Power Supply # of Inputs # of Inputs (without Repeat (with Repeat Relay option) Relay option) 1-25 1-30 1-43 1-60 1-56 1-90 1-60 1-100 External Power Supply # of Inputs # of Inputs (with Repeat (without Repeat Relay option) Relay option) >25 >30 >43 >60 >56 >90 >60 >100

The Field Contact Voltage (FCV) can be provided externally by the user or can be provided by the Field Contact Voltage Supply.

Field Contact Voltage

Customer Input Power 24 VDC 48 VDC 125 VDC 120 / 230 VAC Customer Supplied 12, 24, 48, 125VDC X X X X Annunciator Supplied Field Contact Voltage 24 VDC 125 VDC X X X X X X

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

41

POWER REQUIREMENTS
External AC supply:
(Watts @ Annunciator power input per point)
Annunciator Window Size Full (1 per Cell) Half (2 per Cell) Third (3 per Cell) Quad (4 per Cell) I/O Cards with Repeat Relays 1.7 1.0 0.7 0.7 I/O Cards with no Repeat Relays 1.4 0.7 0.4 0.4

Field Contact Voltage (FCV):

1.8 mA / point (nominal)

Integral AC supply:
(Watts @ Annunciator power input per point)
Annunciator Window Size Full (1 per Cell) Half (2 per Cell) Third (3 per Cell) Quad (4 per Cell) I/O Cards with Repeat Relays 2.2 1.3 1.0 0.9 I/O Cards with no Repeat Relays 1.8 0.8 0.5 0.5

Field Contact Voltage (FCV):

1.8 mA / point (nominal)

42

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Integral Power Supply

The Integral Power Supply is installed in slot 5 of the I/O or CSM Cell depending on the configuration and input power required. The Integral Power Supply provides a 5VDC output used for the Annunciator Logic and LEDs. There are three different types of Integral Power Supplies available: 24VDC 48VDC Universal 125VDC/120/230VAC. Integral Power Supply Cell Locations
Customer Input Power 24 VDC 48 VDC 125 VDC or 120/230 VAC CSM Cell with Integral Pushbuttons X X X CSM Cell with one I/O Module X X I/O Cell with one I/O Module X X X I/O Cell with two I/O Modules X X

Based on the size of the system, there could be several integral power supplies within the Annunciator. The location of integral power supplies within the Annunciator can be noted by the five position terminal block, TB5.

TB5 Power Input Terminal Block

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

43

125VDC or 120/230 VAC Integral Power Supply

This universal integral power supply will accept either AC or DC inputs (not simultaneously) and provides a 5VDC output. Quantity of Inputs per Integral Power Supply
Annunciator Window Size Full Half Third Quad (1 per Cell) (2 per Cell) (3 per Cell) (4 per Cell) I/O Cards with Repeat Relays 25 43 56 60 I/O Cards with no Repeat Relays 30 60 90 100

Systems that exceed these quantities shall use an External Power Supply.

125VDC or 120/230VAC Integral Power Supply (5VDC output)

44

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

125VDC or 120/230VAC Integral Field Contact Voltage (FCV) Supply

The Integral FCV Supply is installed in slot 5 of the I/O Cell. This FCV supply will allow either AC or DC inputs (not simultaneously) and provides a 24VDC or 125VDC output. Quantity of Inputs per FCV Supply
Field Contact Voltage 24 VDC 125 VDC Number of Inputs 250 52

Systems that exceed these quantities shall use an External Power Supply.
+
P1 6 T3 CR5 1 1

C4

F1 R9 Q6 R10

Q5

L1

PS1 PS2

CR6

R3

P12

R4

aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa

+
BR3

R2

F2 R1 C20 R5

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

45

120/230 VAC and 125 VDC Integral Power Supply Wiring

Cell Variations for Power Supply Terminal Blocks (TB5)

I/O Terminal Ass'y Single I/O Module TB5 TB1
1 2 3 4 5 1 2 3 4 5 6 7 8

I/O Terminal Ass'y Dual I/O Module TB5 TB2 TB1

1 2 3 4 5 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

CSM Terminal Ass'y Single I/O Module TB5 TB4 TB3

1 2 3 4 5 J1 J2 1 2 3 4 5 6 7 J3 8 7 8 1 2 3 4 5 6

(Rear View)

(Rear View)

(Rear View)

125VDC Power External 125VDC FCV

TB5 + + 125VDC FCV (internally bussed to TB1,TB2 - 2 & 4) E Power Input
1 2 3 4 5

125 VDC Power Input

125VDC Power External 24 or 48VDC FCV

TB5 Power Input 24 OR 48 VDC FCV (internally bussed to TB1,TB2 - 2 & 4) + + E
1 2 3 4 5

120/240 VAC Power External 24, 48, 125VDC FCV

TB5 Power Input 24 OR 48 VDC FCV (internally bussed to TB1,TB2 - 2 & 4) E + + 1 2 3 4 5

125 VDC Power Input 24 OR 48 VDC FCV Field Contact Voltage

120/240 VAC 50/60 Hz Power Input 24, 48 OR 125VDC FCV Field Contact Voltage

125VDC Power Internal 24V or 48VDC FCV

TB5 Power Input + 1 2 3 4

120/240 VAC Power Internal 24, or 125 DC FCV

TB5 Power + Input 1 2 3 4

125 VDC Power Input

120/240 VAC 50/60 Hz Power Input

125VDC Integral FCV Supply

TB5 Power Input 24 or 125VDC FCV (internally bussed to TB1,TB2 - 2 & 4) + + E
1 2 3 4 5

120/240VAC Integral FCV Supply

TB5 Power Input 24 or 125VDC FCV (internally bussed to TB1,TB2 - 2 & 4) + + E
1 2 3 4 5

125 VDC Power Input

120/240 VAC 50/60 Hz Power Input

46

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

24VDC Integral Power / FCV Supply

This integral power supply is used for 24VDC Power Inputs or whenever external AC/DC power supplies are provided. The 24VDC input is converted to a 5VDC output. An FCV Supply can be added to this integral power supply for systems requiring 125VDC FCV. Quantity of Inputs per Integral Power Supply
Annunciator Window Size Full (1 per Cell) Half (2 per Cell) Third (3 per Cell) Quad (4 per Cell) Field Contact Voltage 125 VDC I/O Cards with Repeat Relays 22 37 49 52 Number of Inputs 52 I/O Cards with no Repeat Relays 26 52 78 87

Quantity of Inputs per FCV Supply Systems that exceed these quantities can use multiple integral FCV Supplies

24VDC Integral Power Supply

(5VDC Output) Shown with 125VDC FCV Supply

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

47

48VDC Integral Power Supply

This integral power supply is used for 48VDC Power Inputs. The 48VDC input is converted to a 5VDC output. Quantity of Inputs per Integral Power Supply
Annunciator Window Size Full (1 per Cell) Half (2 per Cell) Third (3 per Cell) Quad (4 per Cell) I/O Cards with Repeat Relays 22 37 49 52 I/O Cards with no Repeat Relays 26 52 78 87

48VDC Integral Power Supply

(5VDC Output) Shown for external FCV

Note: In order to maintain a UL listing or CE Certification, any customer power supply used to provide 24VDC or 48VDC to the Annunciator shall be UL recognized or CE Certified, and provide basic insulation.

48

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

24 and 48 VDC Integral Power Supply Wiring

Cell Variations for Power Supply Terminal Blocks (TB5)

I/O Terminal Ass'y Single I/O Module TB5 TB1
1 2 3 4 5 1 2 3 4 5 6 7 8

I/O Terminal Ass'y Dual I/O Module TB5 TB2 TB1

1 2 3 4 5 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

CSM Terminal Ass'y Single I/O Module TB5 TB4 TB3

1 2 3 4 5 J1 J2 1 2 3 4 5 6 7 J3 8 7 8 1 2 3 4 5 6

(Rear View)

(Rear View)

(Rear View)

24VDC Power External 24VDC FCV Integral Power Supply

TB5 Power Input 24VDC FCV Internally bussed to TB1, TB2-2&4 + + E
1 2 3 4 5

48VDC Power External 48VDC FCV Integral Power Supply

24 VDC Power Input Power Input 48VDC FCV Internally bussed to TB1, TB2-2&4 TB5 1 2 + 3 - 4 E 5 + 48 VDC Power Input

24VDC Power Internal 125VDC FCV Integral Power Supply

Power Input 125 VDC FCV Internally bussed to TB1, TB2-2&4 TB5 + 1 - 2 + 3 - 4 E 5 24 VDC Power Input

48VDC Power External 24 or 125VDC FCV Integral Power Supply

TB5 1 2 125 or 24VDC FCV + 3 Internally bussed to TB1, TB2-2&4 - 4 E 5 Power Input + 48 VDC or125VDC Power Input 24 OR 125 VDC FCV Field Contact Voltage

24VDC Power External 48 or 125 VDC FCV Integral Power Supply

TB5 1 2 48 or 125VDC FCV + 3 Internally bussed to TB1, TB2-2&4 - 4 E 5 Power Input + 24 VDC Power Input 48 OR 125 VDC FCV Field Contact Voltage

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

49

External Power Supply

For larger systems, an external power supply can be used for 120/230 VAC or 125VDC Input Power. In either case, the external power supply has a 24VDC output used to connect to the Integral 24VDC Supply. The quantity of Integral 24VDC Supplies required is shown in the chart below. Quantity of Inputs for External Power Supplies
(1) AC or DC External Power Supply (2) Integral 24VDC Supplies # of Inputs # of Inputs (without Repeat (with Repeat Relay option) Relay option) 43 52 74 104 98 157 104 173 (2) AC or DC External Power Supplies (4) Integral 24VDC Supplies # of Inputs # of Inputs (without (with Repeat Repeat Relay Relay option) option) 87 104 149 208 195 313 208 347 (2) AC or DC External Power Supplies (3) Integral 24VDC Supplies # of Inputs # of Inputs (without Repeat (with Repeat Relay option) Relay option) 65 78 111 156 147 235 156 260 (3) AC or DC External Power Supplies (5) Integral 24VDC Supplies # of Inputs # of Inputs (without Repeat (with Repeat Relay option) Relay option) 108 186 244 260 130 260 392 433

Annunciator Window Size

Full Half Third Quad

(1 per Cell) (2 per Cell) (3 per Cell) (4 per Cell)

Annunciator Window Size

Full Half Third Quad

(1 per Cell) (2 per Cell) (3 per Cell) (4 per Cell)

For Field Contact Voltage, 24VDC can be derived from the External Power Supply 24VDC Output. For 125VDC, the Integral 24VDC Supply will be used. 120/230VAC

125VDC

External Power Supply

50 SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

125 VDC External Power Supply Wiring

Internal 24 or 125VDC FCV

24 VDC Integral Power Supplies
TB5 24 VDC Power + Input 24 or 125VDC FCV + (internally bussed to TB1,TB2 - 2 & 4) E
1 2 3 4 5
13 14 OK

+ + - -

TB5 24 VDC Power + Input 1 2 3 4 5

Phoenix Quint-PS-100

External Power Supply

L NE

To next Integral Power Supply

+ E Customer Power Input 125 VDC

External 24,48,125VDC FCV

24 VDC Integral Power Supplies
TB5 24 VDC Power + Input 24, 48 OR 125 VDC FCV (internally bussed to TB1,TB2 - 2 & 4) + E
1 2 3 4 5

24, 48, 125 VDC Field Contact Voltage (FCV)

13 14 OK

+ + - -

TB5 24 VDC Power Input 24, 48 OR 125 VDC FCV (internally bussed to TB1,TB2 - 2 & 4) + + 1 2 3 4 5

Phoenix Quint-PS-100

External Power Supply

L NE

To next Integral Power Supply

+ E

Customer Power Input 125 VDC

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

51

120/230 VAC External Power Supply Wiring

Internal 24 or 125VDC FCV

24 VDC Integral Power Supplies TB5 + 1 24 VDC Power Input - 2 24 or 125VDC FCV + 3 (internally bussed to - 4 TB1,TB2 - 2 & 4) E 5 TB5 24 VDC Power Input + 1 2 3 4 5

L N E
6 5 4 3 2 7 1

Customer Power Input 120/240 VAC, 50/60HZ

External Power Supply Meanwell S-150

To next Integral Power Supply

External 24,48,125VDC FCV

24 VDC Integral Power Supplies TB5 + 1 24 VDC Power Input - 2 24, 48 OR 125 VDC FCV + 3 (internally bussed to - 4 TB1,TB2 - 2 & 4) E 5 TB5 24 VDC Power Input + 1 2 3 4 5

24, 48, 125VDC Field Contact Voltage (FCV)

L N E
6 5 4 3 2 7 1

Customer Power Input 120/240 VAC, 50/60HZ

Meanwell S-150

External Power Supply

To next Integral Power Supply

52

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

SOFTWARE CONFIGURATION
APPLICATION
The SERIES 90A Annunciator Configurator application is used to create, edit and download annunciator configurations from a PC. The PC Comm Port connects directly to the annunciator via a serial port on the front of the CSM module. A configuration may be created on the PC without a connection to the annunciator and then downloaded later. The configuration information is held as a file on the PC, which may be edited if a change is required. An exception to this is the physical size of the annunciator, which includes the number of input modules, and the size of each module, which is factory configured. If a configuration is edited, checks are made to ensure that the correct file is downloaded to the annunciator. If more than one version of the SERIES 90A configuration software is used then more than one version of the configuration file can exist. It is up to the user to ensure that copies of the configuration are kept up to date. If the application detects that the local and remote copies of a configuration are different the user can update either. The application also includes a function to enable the configurable options in the annunciator, such as Modbus and DNP communications.

SOFTWARE INSTALLATION
The SERIES 90A configuration software should be installed onto a PC with the following minimum configuration: 300MHz Pentium II CPU Windows 98/2000/XP 64Mbytes RAM 20Gbytes hard disk Insert the AMETEK SERIES 90A Configuration CD in the CD-ROM drive. This will automatically start the installation process. If this does not happen choose Run from the Start menu then browse to the CD-ROM drive and click on Autorun.exe. During the installation, you will be prompted to select the type of Annunciator you wish to configure. Select only the models you wish to use to avoid confusion with extra choices.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

53

SOFTWARE CONFIGURATION INSTRUCTIONS

This is an overview of the configuration steps required for editing or creating an Annunciator configuration. Refer to the next section for additional detail on the menu selections.

Reviewing or editing the Factory Configuration

All Annunciators are factory configured per the model number. Some of these selections, such as Alarm Sequence can be changed with the configuration software. Other features not in the model number, such as N.O./N.C. Inputs, Input Delay, CSM Relay Outputs can also be edited. 1. Remove the front mounted pushbuttons in the CSM Cell (or windows used in the lower right Cell) to gain access to the CSM front mounted Serial Port. Connect the serial (one to one) cable provided with the Annunciator between the SERIES 90A CSM Port and the PC with the Configuration Software installed. (Note: The serial port on the rear of the Annunciator is used for the optional communications; Modbus, DNP, etc. It is NOT used for the system configuration.). 2. Start up Configurator Software. If a default configuration appears, press Cancel. 3. Select Connections, then Settings and configure your PC Serial port for the Com Port where your serial cable is plugged into, 9600 Baud, no parity and address 1 4. Select Connections, and then Connect. If successful, the Annunciator lights will flash fast and a pop up screen will appear with your serial number. Press OK. 5. If you see a screen that says Configuration Mismatch, select Download Configuration from the Annunciator. 6. If you see a screen that says This is not the correct configuration file type for this Annunciator, Select File, and Open up a known configuration file for this type of Annunciator. If a file is not available, follow the instructions below for creating a new configuration. 7. Start the configuration software and select File, New. Select the correct type of Annunciator if prompted. Select Cancel in the configuration menu. Select Connections, and then Connect. You may be prompted to configure certain options not present in your configuration; select NO. Cancel out of any configuration menus. Select Connections, Configuration, Read Configuration. When done, you can Select File, Start Wizard and this will show how the Annunciator is currently configured. 8. Select File, Start Wizard and this will show how the Annunciator is currently configured. You can make changes to any of the selections. For more detail on any of the selection, refer to the next section on the Configuration Wizard. 9. When finished making any changes, select save and enter the file name if
54 SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

prompted. Select Connections, Configuration, Write Configuration. When it is complete, select Connection, Disconnect. Press the TEST pushbutton to verify that everything is functioning correctly.

Creating a new Configuration

New configurations may be created both on-line (connected to an Annunciator) or off-line. 1. Start the configuration software and select File, New. Select the correct type of Annunciator if prompted. 2. The Annunciator Configuration Wizard will start up allowing you to make all configuration selections. Note: When creating a new configuration, make sure you select the correct System Size (rows high x columns wide) and Window Size (1, 2, 3, 4 windows per cell), otherwise, it can disrupt all settings. 3. Select all configuration choices desired (reference the next section for a complete description of choices). When done, save the file. Note: Some options, such as Modbus, DNP, and CSM Relays will not be shown in the New file configuration. Once you connect to the Annunciator, it will indicate which options are available. 4. If off-line during the configuration, you can connect the PC to the Annunciator and download the configuration. (Select Connections, Configuration, Write Configuration.) 5. After you connect to the Annunciator, you may be prompted to configure certain options not present in your configuration. You can configure these options if desired and then save the file when done. Select Connections, Configuration, Write Configuration. When it is complete, select Connection, Disconnect. Press the TEST pushbutton to verify that everything is functioning correctly.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

55

SOFTWARE CONFIGURATION MENUS

Main menu overview
The main application window comprises of five main menus, File, Options, View, Connections and Help. These appear at the top of the screen above the application toolbar, which provides quick access to the main functions of the program.

File Menu
The program manages configuration files through the File Menu. From this menu, you can open, save, and delete configuration files. The File Menu also provides you access to a new "default" configuration as a point of reference.

Options Menu
This menu provides functionality to alter the way your program behaves and appears.

View Menu
Here you can select what you see in main window. Status bar, Tool bar etc.

Connections Menu
Connections menu performs the actual communication with the annunciator to download or retrieve configurations.

Help Menu
The Annunciator Configurator is equipped with a Help Menu to provide the user with assistance for each screen and program function.

56

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

File

In the File menu you will find the following menu options: New Clicking on this will create and open a new configuration. As only one configuration can be open at a time, any previous configuration that is open will be closed. You will be prompted to save any changes before the configuration is closed. New configurations are set to the defaults. Open Here you can browse available locations on your system to open existing configuration files. (file extension "anc").

Save Allows you to save the active configuration file. If the configuration file has already been saved, it will automatically write over the old version. Save As Allows you to save the active configuration file. When clicked, it will ask you for a filename before proceeding. If the filename already exists, it will ask you if you want to overwrite the old version.
SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL 57

Create Duplicate This will create and open a new configuration file; the parameters will be copied from the active (open) configuration and not set to defaults. This allows the same configuration settings to be downloaded to two annunciators. Print This allows you to print the configuration in a text form so that you can see all the parameters. The printout is marked with the time and date of printing. Print Setup This allows you to change your printer settings. Start Wizard This will start the configuration wizard, which will guide you through a set of screens to simply setup your annunciator. Recent Files At the bottom of the file menu, you will also find a list of you most recent configuration files. You can simply click on one of these to open it.

58

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Options

Preferences In the preferences menu you can change the color setup of the whole application, and tell the program how you want the wizard to behave. View Configuration This is a textual overview of the complete configuration. Upgrade This menu option will allow you to add extra functionality to your annunciator and the configurator. Preferences

Colors The colors used to indicate various selections used in the configuration software may be changed. This may be required if they conflict with colors used in the Windows desktop. For most installations the default colors will be acceptable. To change a color first select its usage from the list then click on Change Color and select the new choice from the palate. General If the box beside "Start wizard when opening file" is checked, the wizard will automatically appear every time a new or existing document is opened. As the last open configuration is loaded when the application starts it means that the wizard will also automatically start at this point.
SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL 59

View Configuration (Text)

This allows you to see the complete configuration as text. Once this dialog is shown there are a number of options available.

Copy to clipboard You can use the mouse to select a portion of the configuration and then copy the selection to the clipboard so you can paste it into other documents. If you do not select any text the whole configuration is then copied. Print This will print the complete configuration. Upgrade

The application also includes a function to enable the configurable options in the annunciator. One such is Modbus communications. To enable any of these options you must contact AMETEK Power Instruments with your annunciator serial number that you will find in the Upgrade dialog. You will be given a unique key, which you must type into the box (shown above) and then click upgrade. If you are connected to an annunciator the upgrade will be performed right away. If you are not connected then you must save the configuration and upload it at a later date.
60 SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Note: To successfully obtain the serial number of the annunciator you must have uploaded the configuration at least once. If the configuration has never been uploaded to an annunciator you will get the following message where your serial ID should be. "This configuration has not been uploaded to an annunciator." Connections

Connect & Disconnect From the connections menu you will be able to connect to or disconnect from your annunciator using the Connect and Disconnect menu options. Configuration Once you have successfully connected to your annunciator you will be able to select the Configuration menu option. This will allow you to read and write configurations to and from the annunciator. Settings Here you change your computer's settings to tell it how to connect to your annunciator. N.B. The annunciator functions will not operate while the configurator is connected to the SERIES 90A. Configuration

Read Configuration This copies the configuration from the annunciator into the active configuration. It is recommended that you save any configuration changes before reading a configuration. If you wish to discard your changes you can open another document or close the application opting not to save.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

61

Write Configuration This will copy the active configuration to the annunciator. It is recommended that you save any configuration changes before writing to the annunciator. Note: When a configuration is written to an annunciator the file is, from then on associated with that specific annunciator. As a result of this association, on subsequent sessions there are certain configuration options, which will be disabled. They are listed below. System Name Number of rows Number of columns Alarms per module Number of hardwired inputs Input delay resolution They can only be changed when creating a New Configuration. Note: Changing the system size or window style to something different than your actual Annunciator can cause problems. Communication Settings From this dialog you can select the Com port wish to use to connect and the baud rate and parity of the connection, and the address of the annunciator. These values are stored independently of the annunciator hence care must taken be as if you have more that one annunciator they may not all have the same settings.

Connect Status This option can be used when connected to retrieve the serial ID, the Hardware version and the system description. When nothing is connected the menu option is disabled. This can be used as an indicator to a successful connection.

62

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Configuration Mismatch

When you connect to an annunciator the program checks to see if the active file was the last configuration to be downloaded to the annunciator, if this is not the case then the message shown above will be displayed. A Configuration mismatch may occur as a result of the following: 1) You have opened the wrong configuration file. 2) Someone else has downloaded a different configuration to the annunciator. If you choose the first option "Download configuration from annunciator" this will copy the configuration from the annunciator in to the active file. If you choose the second option "Overwrite configuration on annunciator with configuration....." this will copy the configuration in the active file to the annunciator. In the case of a configuration mismatch it is recommended that you select the first option and then save this configuration to another location as a backup.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

63

Serial ID Mismatch

A serial ID mismatch occurs when you try to upload a configuration that has already been uploaded to another annunciator. When you upload a configuration, a note is kept of which annunciator it "belongs to". Every time you connect to an annunciator the stored serial ID is checked to make sure that it matches the annunciator you are connected to. In the case of a serial ID mismatch if you hit continue you will be able to read the configuration from the annunciator but you will not be able to write the active one to the annunciator. To rectify this situation you should click "No" and then open the correct configuration file, or create a new configuration.

64

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Configuration Wizard
The configuration of an SERIES 90A is defined in a number of sections, which are displayed on separate pages. The pages may be selected by clicking on the labeled tabs at the top of each page. When a system is configured for the first time the Next >> button may be used to move through all the sections. This will ensure that no sections are missed. The << Back button may be used to go to the previous page if required. A graphical representation of the annunciator is used to simplify the configuration. This mimic diagram may be given the same window colors as the actual unit to make correct input selection easy. Individual or groups of inputs or modules can be selected by clicking on them. (To select a group of inputs, select an input with the mouse and hold & drag across other cells. You can also use the Ctrl key to pick a group of inputs.) The Configuration Wizard Screens and their functions are detailed below: System: Used to configure System Size (High x Wide), Window size per cell and other system-wide features. Once configured and downloaded it will be locked to prevent any further changes. Input Configuration: Used to select individual settings per input, such as input delays, repeat relay operation, critical/non-critical alarms, alarm sequence groups. These settings can be edited or changed at any time. Lamp Configuration: Used to configure flash rates for slow, fast and intermittent speeds as determined by the operating sequence. Sequence: Selection of the operating sequence for each alarm group. CSM: Switch Input: Modbus: DNP: Set-up of auxiliary relays and other system-wide functions. Set up for optional external switch inputs and Test Pushbutton operation. Modbus set-up configuration. (Only shown when option is enabled.) DNP set-up configuration. (Only shown when option is enabled.)

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

65

System

The hardware configuration is defined in this page. The values must match the actual size of the SERIES 90A. A mimic diagram of the annunciator is shown on the left hand side. The blank section on the bottom right of the annunciator is the Common Service Module (CSM).

Note: After the configuration is uploaded to the annunciator for the first time the system parameters cannot be edited. The controls will be disabled. Care should be taken that the System values are correct. To make a change, you must create a new configuration. System Name (ID) This name is used to uniquely identify the annunciator. Up to 16 characters may be used.

66

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Rows and Columns of Modules Use the up or down arrows to the right of each value to set the actual number of modules. The AN3100D annunciators are limited to 13 rows or 13 columns and a maximum of 200 alarms or 50 Cells. (Example: a 13 x 4 system is not allowed, but a 5 x 10 is.) Alarm points per module There may be 1, 2 or 4 points per module as determined by your window size. Quad size windows use 4 points per cell, Triple Size windows use 3 per cell, Dual or Half Size windows use 2 per cell and Single or Full Size windows use 1 point per cell. By default all modules have the same number of points. If different numbers of points per module are required (Option IMW) click on the Advanced button. Hardwired inputs The default is that all inputs are hardwired, which refers to the field contacts wired to the back of the annunciator. On the mimic diagram the hardwired inputs are shown with a dot at the center. Non-hardwired inputs refers to inputs that are received via the serial communications. Non hard-wired inputs do not respond to the I/O cards or field contact inputs. Note: Serial Communications may be used for both Hardwired and NonHardwired systems. Input delay resolution This determines the system-wide increment value for the input delay (or response) for each alarm. It is used in conjunction with the individual input delay setting in the Input Configuration Screen. The setting is based on whether your maximum input delay will be 12.5 seconds or 250 seconds. You have 255 increments of the value selected. For the 50ms setting, you can have a selectable software delay in 50 msec increments up to 12.5seconds. For the 1sec setting, you have a selectable software delay in 1 second increments up to 250 seconds. Each input can have its own delay assigned as shown in the Input Configuration page, however, this system setting (50msec or 1 sec) is applied across the whole system. Integral Push Buttons (Option INTB, NPB) These are the pushbuttons located in the lower right cell of the Annunciator System. They include Annunciator Functions: Test, Acknowledge, Silence and Reset. They are provided when specified in the model number, using model code INTB. When model code NPB is specified, the integral pushbuttons are not installed and the software box should be unchecked, to allow up to two active alarm windows in this position. For either selection (INTB or NPB), external pushbuttons can be connected to the Annunciator terminal blocks with the same functionality. Single Input I/O board (Option 2S)
SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL 67

This is selected whenever window size option 2S (two point windows with single input per I/O board) is selected. The standard I/O board has two inputs available, but in certain configurations, as listed above, it is necessary to only activate a single input on this module. Dual Relay (Option 2RR) This will provide two repeat relay outputs (each selectable for Form A or Form B operation) for every input. This is only available whenever window size option 1 (single point windows) or 2S (two point windows with single input per I/O board) are selected. Flash Synch Master (Option FS) A software selection box is provided for flash synchronization between several different SERIES 90A Annunciators. In systems that require flash synchronization, one Annunciator is configured as the Master (box checked) and all others are configured as the Slave (unchecked). Wiring between the Annunciators is required to share the flash signals. (Reference the Common Service Cell Wiring diagrams.) In systems that don't require flash synchronization, the Flash Sync Master box must be checked. When setting up a system for flash synchronization, the flash lamp rates should be configured as follows: (reference the Lamp Configuration Screen) Master and Slave Lamp Flash Rates should be identical except, on the Slave units, set the Slow Flash On time approximately 0.1 sec lower than the Master. This ensures the slave unit is ready and waiting for the sync edge from the master. Set the Slow and Fast rates in even multiples. (Example: Slow Flash = 1.0 sec, Fast Flash = 0.5 sec). Use of intermittent flash is not recommended. Use alarm sequences that are either identical between master/slave units or ones that share the same flash rates (slow, fast, etc.) Note: If a Slave unit does not receive the flash synchronization signal from the Master unit, the slow flash will become steady on.

68

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Input Configuration

The configuration of each alarm input is defined in this page. To simplify this procedure a number of similar inputs may be selected at the same time and common parameters set. An individual input is selected by clicking on it. The input will change color when selected. The input number will be shown in the Alarms list. To select a number of inputs hold down the Ctrl key while clicking on the inputs. To de-select an input press the Ctrl key and click on the input again. To select a rectangular block of inputs click on the top left hand one then drag down to the bottom right. When one or a number of inputs has been selected the parameters for those inputs may be set.

Alarm Numbering
The inputs are numbered left to right and top to bottom. The inputs within a module are numbered in sequence followed by the next module. So, for example, the top row of inputs of modules with four inputs each are:1, 2, 5, 6, 9, 10,

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

69

Relay Mode (optional) If the repeat relay option has been included with your system, you may select the Relay Mode for each input as follows:-

Follows Input Contact Normally Energized The repeat relay will follow the status of the field contact, regardless of the pushbuttons pressed. In this mode, the relay coil is energized in the normal (nonalarm) state. Follows Input Contact Normally De-Energized The repeat relay will follow the status of the field contact, regardless of the pushbuttons pressed. In this mode, the relay coil is de-energized in the normal (non-alarm) state. Latched Alarm till ACK Normally Energized The repeat relay will change state during an alarm and latch on until the acknowledge pushbutton is pressed, which returns the relay to the normal state. In this mode, the relay coil is energized in the normal (non-alarm) state. Latched Alarm till ACK Normally De-Energized The repeat relay will change state during an alarm and latch on until the acknowledge pushbutton is pressed, which returns the relay to the normal state. In this mode, the relay coil is de-energized in the normal (non-alarm) state. Latched Alarm till Reset Normally Energized The repeat relay will change state during an alarm and latch on until the reset pushbutton is pressed, which returns the relay to the normal state. In this mode, the relay coil is energized in the normal (non-alarm) state. Latched Alarm till Reset Normally De-Energized
70 SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

The repeat relay will change state during an alarm and latch on until the reset pushbutton is pressed, which returns the relay to the normal state. In this mode, the relay coil is de-energized in the normal (non-alarm) state. Follows Lamp Display Normally De-Energized The repeat relay will follow the state of the lamp display for that input. When the display is flashing on and off, it will toggle open and closed at the slow flash rate. When the lamp display is on steady, the repeat relay contact will be closed. It will open when the lamp turns off. Note: In addition to these configurations, the repeat relay contact may be selected as a Form A or (Normally Open) or Form B (Normally Closed) using the I/O jumpers described in the previous section. Alarm Group Each input belongs to one of 4 groups. The groups define the alarm sequences that are set in the 'Group page. This allows up to 4 first out groups per system or four different sequences. Input delay This is also referred to as the input response time, which is the amount of time an input must be in the alarm state before it is recognized as a valid alarm. Each input may be set from 1 second to 250 seconds in 1 second increments or from 50 msec to 12.5 seconds in 50 milliseconds increments. The system wide input delay resolution (50ms or 1sec) is set on the System page. Systems with FR Option enabled (1 msec response) will have an additional software selection shown for 1 msec input. Note: The Input Delay is the total delay including hardware and software filtering. For AC Inputs, there will be an additional 40 msec hardware filtering delay added to these numbers. Critical alarm Alarms may be selected as critical or non-critical for segregating inputs into a common alarm relay output on the CSM. The CSM has separate relays for critical or non-critical horns, reflash and fault outputs. Any input in the system selected for critical or non-critical will activate the respective CSM relay output. By default, all alarms are set as non-critical. Modbus Transmit or Receive (Optional) If the Modbus option is included with your system, every input is defined for Transmit or Receive by clicking on the button. Transmit implies that the alarm status from hardwired contacts are sent serially to some other device. Receive implies that some other serial device is providing the status of the alarm and the Annunciator will respond as if it were a field contact input. You may choose
SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL 71

combinations of transmit and receive, but a single input cannot do both. You may also set up an input as receive while providing a hard-wired contact input to the same point. In this case, the Annunciator will respond to alarms from either the contact or serial input in a logic OR arrangement. If the option is not available this button is not displayed. It may also not be displayed if creating a new configuration. You must connect to your Annunciator to enable the serial Modbus configuration. Note: Systems with Serial Inputs only (not Hardwired) cannot be set to transmit. Panel Colors The color of each input in the mimic diagram may be changed to match the actual annunciator. To do this, select all the inputs with the same color as described above then click on Panel Colors'. From the color selector dialog choose any color. The custom colors represent the available window colors. Repeat this for each color. Table View Click on the Table View button to display the current input configuration in a table format. This is designed to be a summary of all the input configuration, but by clicking on the individual items you can change the selection from the table. The column widths may be adjusted by clicking and dragging on the vertical separators between the column titles.

72

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Lamp Configuration The lamp flash rates are defined in this page. The operational sequence chosen determines whether a slow, fast or intermittent flash rate is used. For example; Sequence TFS uses all three rates while Sequence AF uses only the slow flash rate. Click on the up or down arrows beside each number to increment or decrement it. Click and hold on the arrows to scroll up or down. Click on the Test button to check the appearance of each flash rate. Fast & Slow flash rates The ON and OFF times are set up with a resolution of 0.1s. The maximum times are 4s. Intermittent rate The Intermittent period values will be automatically adjusted to ensure they are integer multiples of the sum of the Intermittent ON and OFF times. The maximum Intermittent Period ON and OFF values are 25s. Note: The intermittent on period may be adjusted automatically by the wizard so that it is set to at least one full intermittent on - off cycle.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

73

Sequence

The alarm sequence for each input group is defined in this page. The Input Configuration page was used to indicate which of the four available groups was assigned to each input. This page identifies the sequence chosen for each group. Note: The four available groups can be set up for the same First-Out Sequence, but each group is treated separately as its own first out group. To change the alarm sequence, click on the entry then choose the sequence from the list. LN Automatic reset, non-locking, no flash, no audible, no PB AO Automatic reset with lock-in of alarms, no flash AONL Automatic reset, non locking, no flash AF Automatic reset with lock-in of alarms AFNL Automatic reset, non locking FR Automatic reset with lock-in of alarms, flash reset AM Manual Reset with lock-in of alarms FRM Manual Reset with lock-in of alarms, flash reset AS First out fast flash, subsequent alarm steady, auto reset ASFR First out fast flash, subsequent alarm steady, auto reset, w/ silence ASFRM First out fast flash, subsequent alarm steady, first out reset, w/ silence TFS First out, triple flash, first out reset TFSFRM First out, triple flash, first out reset, flash reset, reset TFSM First out, triple flash, first out reset, reset ARR Ringback, dual flash, lock-in of alarms until acknowledged FRR Ringback, dual flash, lock-in of alarms until acknowledged, flash reset VS First out, dual color, single flash, with first out reset VSRR First out with ringback, dual color, dual flash, with first out reset, reset MC Motor Control
74 SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

CSM (Common Service Module)

The functions of the CSM are defined in this page. Common Relay There are 2 relays in the CSM and an additional 2 can be provided with option RLY. Each relay mode may be defined as either Energized or De-Energized, with respect to the power on, normal state. For example, a Energized Relay has a coil that is energized when power is applied and there is no alarm. When the output is activated, the coil will de-energize, transferring the contact output. The Standard relay functions may be selected from:Critical horn Auxiliary horn output driven by any alarm selected as critical. The horn relay output will return to its normal state upon activation of the silence or acknowledge pushbutton. Non-critical horn Auxiliary horn output driven by any alarm selected as noncritical. The horn relay output will return to its normal state upon activation of the silence or acknowledge pushbutton. Note: If a critical horn is used in addition to the non-critical horn, the critical horn has priority. For example; if the non-critical alarm is on and the Annunciator receives a critical alarm, the non-critical horn will turn off and the critical horn will turn on. When the critical horn is silenced, any new non-critical alarms will activate the non-critical horn. This operation can be changed in the common functions below. Ringback (clear horn) An output driven by the return to normal of an alarm input. Operated by sequences ARR, FRR, and VSRR only. The following functions are included with the RLY Relay Option: Critical Reflash Grouped output driven by any alarm selected as critical. Upon a critical alarm, the relay output changes state. Every new critical alarm will pulse the relay output for approximately second. The relay output will return to
SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL 75

its normal state when all critical alarms have returned to normal. Non-Critical Reflash Grouped output driven by any alarm selected as noncritical. Upon a non-critical alarm, the relay output changes state. Every new noncritical alarm will pulse the relay output for approximately second. The relay output will return to its normal state when all critical alarms have returned to normal. Critical Fault This relay output will change state when any critical input is in the alarm state. The relay output will only return to its normal state when all critical alarms have returned to normal. The relay output is not affected by the silence or acknowledge pushbutton. Non-Critical Fault This relay output will change state when any non-critical input is in the alarm state. The relay output will only return to its normal state when all non-critical alarms have returned to normal. The relay output is not affected by the silence or acknowledge pushbutton. Power Fail This relay output will change state when the Power is lost. The relay coil is energized upon start-up and the contacts will transfer upon a loss of power. Ground Fault This relay output will change state when a ground fault condition is detected. (Note: Must have Ground Fault Detector Option GF) The ground fault can be either a positive ground (+FCV wire to ground) or a negative ground (FCV return wire to ground). Watchdog System healthy output. It will activate when the system is not processing alarms, like during the configuration process or when there is a system failure. The Watchdog will detect when there is a remote communication failure, if Modbus or DNP are used. The communication failure would activate after a period of inactivity, including a disconnected or broken cable. The Configuration Screen will show a summary of the Common Relay functions to the right. To select a relay to edit use the up or down arrows beside the relay number or click on the entry in the summary. Note: In addition to these configurations, the repeat relay contact may be selected as a Form A or (Normally Open) or Form B (Normally Closed) using the I/O jumpers described in the previous section. Common Functions A number of system-wide functions are available through the Common Service Module. To select a function click on the white box to the right of the name so as a tick mark appears. To turn the function off click on the box again so as the tick is removed. The available functions are:Enable Internal Horn (Option HN) When selected, this will activate the internal audible device upon any non-critical or critical horn condition.
76 SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Internal Horn Silence (option AS) The internal horn (option HN) may be automatically silenced after a fixed time. To do this use the up and down arrows to the right of the value box to set the required time. The maximum value is 240s and the resolution is 1.0s. Note: A setting of 0 indicates that the auto-silence is not activated. External Horn Silence (Option AS) This will silence any external horn if selected for CSM Relay #1-4 in the time increment selected. This will automatically silence the Critical, Non-Critical or Ringback Horn when this option is included with the system. The maximum value is 240s and the resolution is 1.0s. Note: A setting of 0 indicates that the auto-silence is not activated. Auto Reset This will activate the Reset function continuously, eliminating the need to manually press this. (Note: this only applies to alarm sequences that require the reset function.) Critical Audible has no affect on non-critical This will make the operation of the non-critical horn independent of the critical horn. See the previous section on the operation of the non-critical audible. Critical Audible Pulsed This will pulse the critical audible output upon an alarm. Non-critical Audible Pulsed This will pulse the non-critical audible output upon an alarm. Ringback Audible Pulsed This will pulse the ringback audible output upon an alarm.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

77

Switch Inputs

This screen is used to set up the optional External Switch Inputs (Option SW). The External Switch Inputs provide several inhibit functions that are commonly used when the system is left in a in-manned state and there is no need to flash alarms or sound horns. There are other configurations available on this page to configure the Test Pushbutton Operation.

External Switch Function Settings

LED Lamp Inhibit If selected, whenever the switch is closed, all LED Lamps in the system will be disabled. If the operational sequence chosen latches the alarm (AO AM, etc.), any alarms that occurred while the inhibit switch was enabled as well as any current alarms will be displayed as soon as the switch returns to the off position. Horn Inhibit If selected, whenever the switch is closed, all Horns in the system will be disabled. (This includes the internal horn and external horns connected to the CSM Relay outputs.) If the operational sequence chosen latches the alarm (A, M, etc.), any alarms that occurred while the inhibit switch was enabled as well as any current alarms will be sounded as soon as the switch returns to the off position. Repeat Relay Inhibit If selected, whenever the switch is closed, all Repeat Relays in the system will be disabled. If the operational sequence chosen latches the alarm (AO, AM, etc.), any alarms that occurred while the inhibit switch was enabled as well as any current alarms will operate as soon as the switch returns to the off position.
78 SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Inhibit all CSM Relay Outputs If selected, whenever the switch is closed, all CSM Repeat Relay Outputs (Horns, Reflash and Fault) will be disabled. If the operational sequence chosen latches the alarm (AO, AM, etc.), any alarms that occurred while the inhibit switch was enabled as well as any current alarms will operate as soon as the switch returns to the off position.

Test Configuration
The following functions can be activated when the Test Pushbutton is used. It applies to the Integral Test Pushbutton on the CSM Module (Option INTB) and to an external Test Pushbutton wired into the Annunciator. 1. Audible If selected, the audible outputs (critical, non-critical and ringback horn) will be activated during the Test Function. The LED Lamps will always be activated during the Test Pushbutton. There is no selection to de-activate this.

2.

LED Lamps:

3.

Repeat Relays: If selected, the Repeat Relay outputs will be activated during the Test Function.

Other System Configurations

Auto Acknowledge This will activate the acknowledge function continuously, eliminating the need to manually press this. (Note: by selecting this, you will never get any horn outputs and flashing lamps, depending on the sequence selected.) Control Interlock This requires that the Silence, Acknowledge and Reset pushbuttons are pressed in this exact order. Anything else will be ignored. For example; if the Acknowledge pushbutton is pressed before the Silence, it will not have any effect. (Note: If the Reset function is not required for the alarm sequence selected, it will be ignored.)

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

79

Modbus
Note: These options will only be available if the Modbus functionality has been purchased from AMETEK. Default values of the Modbus settings are given in Appendix B

Settings for Ethernet (Option ETH)

Local IP Address This is the static IP address to be assigned to the annunciator so that it can be located on a network. Remote IP Address When the annunciator is operating in Master mode this is the address to which it will send data requests. Subnet Mask To allow the annunciator to be successfully connected to your network you will have to provide the correct subnet mask. If you do not know the correct subnet mask then you should contact your network administrator. Default Gateway Please contact your network administrator to find out whether you need to set a gateway to successfully connect to your network. Port Address Select the Port Address of the host system on the network.
80 SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Common Modbus Settings

Modbus Address In master mode, this is the address of the slave annunciator that the master will connect to. In slave mode this address is the annunciators own local Modbus address. Every system on a common serial bus must be given a unique address. Valid addresses are from 1 to 255. Receive & Transmit Start Address This defines the base register address for sending and receiving information. Parity The parity for the serial communications may be selected from:None Odd Even

The configuration application will always use the parity defined for the SERIES 90A. If the parity is changed it will not take affect until the current configuration session is complete. Baud Rate The Modbus baud rate may be selected from :1200 2400 4800 9600 19200

The configuration application will always use the baud rate defined for the SERIES 90A. If the baud rate is changed it will not take affect until the current configuration session is complete. Modbus Mode The Modbus Mode may be selected from:Master Slave

A Master unit may issue command functions and a slave unit responds to them. When the SERIES 90A configuration application is being used the SERIES 90A will be in slave mode independent of its Mode setting.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

81

Data Type The Modbus Data Type may be selected from:AN3135 Point State Point State

Reference Appendix A for a complete description of these Data Types. Slave Address This is used when the SERIES 90A is selected as a Modbus Master. The Slave Address refers to the device that the Master is communicating to. Valid addresses are from 1 to 255. Transmit Controls If this option is selected, Acknowledge and Reset Pushbutton controls will be transmitted along with point data. (When communicating between two Annunciators, only one Annunciator may be set to Transmit Controls. As a default, the Annunciator will always accept or receive pushbutton controls from another device regardless if the Transmit Controls option is selected. Modbus Type This is a format in which the data is transmitted. Can be set to ASCII or RTU.

82

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

DNP3.0

Note: These options will only be available if the DNP3.0 functionality has been purchased from AMETEK. The DNP3.0 option is currently only available on the SERIES 90A annunciators. The default DNP settings are given in Appendix C.

Settings for Ethernet (Option ETH)

Local IP Address This is the static IP address to be assigned to the annunciator so that it can be located on a network. Remote IP Address When the annunciator is operating in Master mode this is the address to which it will send data requests. Subnet Mask To allow the annunciator to be successfully connected to your network you will have to provide the correct subnet mask. If you do not know the correct subnet mask then you should contact your network administrator. Default Gateway Please contact your network administrator to find out whether you need to set a gateway to successfully connect to your network. Port Address Select the Port Address of the host system on the network.
SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL 83

Common DNP Configuration Settings

IED Address This is a number used to identify the recorder on the network (range 1 - 65534). Transmission delay This is the time to disable the master transmitter on an RS485 network (range 0 65535) (not currently used). Data Link Confirm This can be set as Never, Sometimes or Always. The default value is Never. Retries This is the number of times the recorder will retry to connect if Data Link confirmation is required (range 0 - 255) Timeout This is the time the IED will wait for a Data Link confirmation. Valid numbers are 0 - 65535. Select/Operate arm time This is the time period after the select command is received that the operate command will be performed (range 0 - 65535) (Not currently used) Communications port The Baud rate of the recorder's serial port can be set by selecting a value from the Baud rate drop down list box. The DNP baud rate may be selected from :1200 2400 4800 9600 19200

84

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Quick Access Toolbar

Hot Keys

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

85

SYSTEM SPECIFICATIONS
INPUTS
Field Contacts Normally Open (N.O.) or Normally Closed (N.C.) Input selection through Software or Field Selectable Jumper Wet (voltage supplied) or dry (voltage free) contacts Field Contact Voltage (FCV) Common FCV or FCV Isolated Input to Input (Jumper Selectable) 12, 24, 48, 125 VDC, 120 VAC or 24VDC open collector Input Current Requirement: 0.0018 mA per input FCV Disconnect for an alarm when the I/O Module is removed (other alarms unaffected) Input Isolation Each input is optically isolated Input Response 1 millisecond 50 milliseconds 50 msec to 250 seconds (Fast Response, Option FR. Also used with SER option) Standard Response Adjustable in Software in 50 msec or 1 second increments

Display
Window Sizes Full Size (1 per Cell): Half Size (2 per Cell): Third Size (3 per Cell): Quad Size (4 per Cell): Illumination White LED 20 mA @5VDC Full Size Windows 8 LEDs / Input Half Size Windows 4 LEDs / Input Third Size Windows 2 LEDs / Input Quad Size Windows 2 LEDs / Input Window Color White, Red, Yellow, Amber, Green, Blue Legends Laser printed on transparency film or Engraved 3.0 x 3.0 (76 x 76mm) 1.5 x 3.0 (38 x 76mm) 1.0 x 3.0 (25 x 76mm) 1.5 x 1.5 (38 x 38mm)

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

87

Repeat Relay Outputs

Repeat Relay Option RR Individual relay per point Follows field contact or alarm sequence, selectable in Software Energized or de-energized Relay Coil, selectable in Software Form A or Form B (N.O. or N.C.) Contact, selectable by Jumper -Available with all window sizes Repeat Relay Option 2RR Two repeat relays per point Follows field contact or alarm sequence, selectable in Software Energized or de-energized Relay Coil, selectable in Software Form A or Form B (N.O. or N.C.) Contact, selectable by Jumper -Available with full or half size (option 2S) windows Repeat Relay Option FRC Individual repeat relay per point Follows field contact or alarm sequence, selectable in Software Energized or de-energized Relay Coil, selectable in Software Form C (SPDT) Contact, selectable by Jumper -Available with full or half size (option 2S) windows Relay Operation Follows Field Contact: Follows Alarm Sequence: Repeat Relay Output Follows Input Contact State Repeat Relay Output Latches on Alarm until Acknowledged or Reset Follows Alarm Display: Repeat Relay Output toggles on and off following operation of window Relay operation selectable in Software per point Relay Ratings: 24VDC @ 3.0 Amps 110VDC @ 0.1 Amps 120VAC @ 3.0 Amps Resistive Load

88

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Alarm Sequence
Sequence Selections LN AO AONL AF AFNL FR AM FRM AS ASFR ASFRM TFS TFSFRM TFSM ARR FRR VS VSRR MC Up to 4 Sequences per system (configured in software by input) Automatic reset, non-locking, no flash, no audible, no PB Automatic reset with lock-in of alarms, no flash Automatic reset, non locking, no flash Automatic reset with lock-in of alarms Automatic reset, non locking Automatic reset with lock-in of alarms, flash reset Manual Reset with lock-in of alarms Manual Reset with lock-in of alarms, flash reset First out fast flash, subsequent alarm steady, auto reset First out fast flash, subsequent alarm steady, auto reset, w/ silence First out fast flash, subsequent alarm steady, first out reset, w/ silence First out, triple flash, first out reset First out, triple flash, first out reset, flash reset, reset First out, triple flash, first out reset, reset Ringback, dual flash, lock-in of alarms until acknowledged Ringback, dual flash, lock-in of alarms until acknowledged, flash reset First out, dual color, single flash, with first out reset First out with ringback, dual color, dual flash, with first out reset, reset Motor Control

Customized flash rates 100 millisecond increments (Selectable in Software) First Out Groups Up to 4 first out groups per system 5 millisecond First Out Discrimination Lamp Synchronization Synchronize other displays to same flash rate. Master system outputs a pulse at the slow flash rate. Slaves re-sync to incoming lamp off edge. A master system may drive up to 5 slave units.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

89

Controls
Pushbuttons Integral Pushbutton Option (INTB): Test, Acknowledge, Silence and Reset (4) External Pushbutton Inputs:Test, Acknowledge, Silence and Reset 5VDC @0.002 mA per Pushbutton (provided by Annunciator) Switch Input (Option SW) Software configurable for: Inhibit of LED Lamps, Horn, Repeat Relay Outputs or CSM Common Relay Outputs 5VDC @0.002 mA (provided by Annunciator)

System Relays
Alarm Grouping Critical or Non-Critical Alarms: Selectable in software per input Used to provide separate horns, or other relay outputs Critical Alarms have priority over Non-Critical (can be disabled) Standard Relays (2) Relays Software Configurable for: Critical or Non-Critical Horn, Ringback Horn Energized or De-Energized Relay Coil, selectable in Software Form A or Form B (N.O. or N.C.) Contact, Selectable by Jumper Optional Relays (Option RLY) (2) Additional Relays Software Configurable for: Critical or Non-Critical Horn, Ringback Horn, Critical or Non-Critical Reflash, Critical or Non-Critical Fault, Power Fail, System Watchdog, or Ground Fault Detect) Energized or De-Energized Relay Coil, selectable in Software Form A or Form B (N.O. or N.C.) Contact, Selectable by Jumper Relay Ratings: 24VDC @ 3.0 Amps 110VDC @ 0.1 Amps 120VAC @ 3.0 Amps Resistive Load

Audible Devices
Internal 80db @ 30cm audible device (option HN) External Audible Devices available

90

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Communications
Communication Options
Option SIM Modbus Input Only No Yes Yes Yes Yes Yes Yes Yes Yes Option MB Modbus Input & Output Yes Yes Yes Yes Yes Yes Yes Yes Yes Option DNP DNP Output Yes No N/A No Yes Yes Yes Yes Yes Option SD Serial ASCII Output Time stamped alarms only No N/A N/A N/A No No Yes Yes

Function

Transmit Alarm Status via Serial Data Receive Alarm Status via Serial Data RTU or ASCII Mode Master Mode Slave Mode Transmit Local Pushbutton Controls Receive Remote Pushbutton Controls RS-232 / 485 Ethernet (Option ET)

Time Stamped Alarms

Sequential Events Recording Time Stamp Resolution: Time Set Method: Time Synchronization: Data Output: Data Format: Event Storage: (Option SER, SERFR) 1 or 4 millisecond (depending on option selected) Through Configuration Software Internal Clock (accurate to 10 seconds per day) Optional IRIG-B Module (accurate to 1msec) Modbus, DNP or ASCII Point Number, Point Status, Time & Date of alarm and subsequent return to normal. 500 Events (an event can be a point on alarm or a point that returns to normal)

Power Requirements
Input Power 19-29 VDC (Option F 24VDC) 38-58 VDC (Option E 48VDC) 100-250 VDC (Option C 125VDC) 88-132 VAC, 60 Hz (Option B 120VAC) 176-264 VAC, 50 Hz (Option A 230VAC) Input Burden: Maximum 2.2 Watts/point (depends on window size and options selected)

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

91

Mechanical
Enclosures: Semi-flush Panel Mount, 19 Rack Mount, Surface (wall) mount, NEMA Enclosures Depends on Annunciator Configuration (# of cells high x wide)

Size:

Weight: 1.5 LB per cell (0.8kg per cell)

Connections / terminations
Field Contact Input, Relay Output, Power Input Terminals -Barrier Terminal Block, #6-32 screw. Accepts Ring, Spade Lug or Bare Wire -Wire size: 12-22 AWG Pushbutton/Switch Input, Lamp Synchronization Terminals -Barrier Terminal Block, #6-32 screw. Accepts Ring, Spade Lug or Bare Wire -Wire size: 14-22 AWG Serial Communication Port(s) 9 Pin Female D connector Ethernet Communication Port -RJ45 connector IRIG-B Time Synchronization Input -BNC connector

92

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Environment
Operating Temperature Range: Storage Temperature Range: Humidity: -20 TO 50 OC (-4 to 122oF) -20 TO 80 OC (-4 to 176oF) 20-95% RH

Electrical
Surge Withstand: ANSI C37.90.1 (Oscillatory portion) Electrical Fast Transient/Burst Immunity: IEC 61000-4-4 (2kV DC Power, 1kV I/O) Surge Immunity: IEC 61000-4-5 (1kV Common Mode, line-to-ground) Dielectric Withstand: 1400 Vac or 2050 Vdc Inputs to Digital (test @ configuration port) 1400 Vac or 2050 Vdc Outputs to Digital (test @ configuration port) 1450 Vac or 2150 Vdc AC Integral Power Input to Digital (test @ configuration port) 350 Vac or 500 Vdc DC Integral Power Input to Digital (test @ configuration port) 1400 Vac or 2000 Vdc from Inputs to Outputs 1400 Vac or 2000 Vdc from Inputs to Power Input 250 V RMS from Input to Input when configured for Isolated Inputs 1400 Vac or 2000 Vdc from Outputs to Power Input 1200 Vac or 1700 Vdc from Output to Output 1400 Vac or 2000 Vdc from Inputs to Case 1200 Vac or 1700 Vdc from Outputs to Case 1400 Vac or 2000 Vdc from Integral AC Power to Case 350 Vac or 500 Vdc from Integral DC Power to Case 350 Vac or 500 Vdc from Communications Ports to DC Power 1450 Vac or 2150 Vdc from Communications Ports to AC Integral Power Input Radiated RFI Immunity: Conducted RFI Immunity: Radiated Emissions: Conducted Emissions: Radiated Power Frequency: ESD Effects: IEC 61000-4-3 10 V/m IEC 61000-4-6 3V

EN 61000-6-4 (EN55011) EN 61000-6-4 (EN55011) IEC 61000-4-8 IEC 61000-4-2 30 A/m Magnetic Field 4kV contact 8kV air

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

93

Certifications
CE: FM 1 FM-C1 UL: ULC: ULR CSA Low Voltage Directive 73/23/EEC: EN 61010-1:2001 EMC Directive 89/336/EEC: EN 61326:1998 Class 1, Division 2, groups A, B, C, and D (FM Canada) 2017 (UL Canada)

Requires FM option (refer to option codes). The required door may be supplied by Ametek, a panel shop or the customer. The door must meet the FM standard for requiring a tool to open or remove the door to allow access to the front of the Annunciator.
SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

94

Servicing
Ensure that the power supply to the unit is switched off before servicing.

MODULE REMOVAL
When removing a module for replacement or configuration, it is best to shut off the power to prevent any false alarms or electric shock. When replacing any board, note the jumper settings and transfer them to the replacement module. If in doubt, refer to the module set-up instructions in this manual.

CAUTION
Note and record the window positions when removed from the chassis so as to ensure that the windows are replaced in their original locations Severe problems/damage could occur to monitored plant/equipment should windows be replaced in incorrect positions causing erroneous indication of alarms Only remove one window assembly at a time to minimise the possible incorrect repositioning of alarm display windows

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

95

ESD
ESD (Electrostatic Discharge) can damage sensitive electronics when they are being handled or touched. The Annunciator has been protected against certain levels of ESD when touching the outside case or terminals. The internal electronics may be susceptible to ESD when handled, so proper care should be given to any exposed electronics or circuit boards. The following guidelines should be used to prevent any build-up of ESD and to minimize the products exposure to it. 1. Prevent static build-up by using conductive paints, carpeting, mats and metal surfaces. Use appropriate grounding techniques, including wrist and heel straps for personnel. 2. Store or transport electronic devices, parts and assemblies in conductive bags or bins. 3. Only perform repairs at an appropriate repair station. 4. When handling electronic assemblies or printed circuit boards try to avoid touching traces on the printed circuit board or the static sensitive devices. 5. Remember that tools are a source of static electricity. Only use grounded soldering irons. Ground tools before using them to bleed off any charge buildup. 6. Discharge yourself before touching or handling any electronic assembly or device. This can be done by touching a good ground point before touching any electronic devices or assemblies. Preferably, discharge any static charge through a high impedance such as a wrist or heel strap.

96

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

APPENDIX A
OPERATIONAL SEQUENCES
The following are summary sequence descriptions provided for guidance.
AUTO RESET, NON LOCKING STATUS ONLY INDICATION, NO AUDIBLE
SEQUENCE CODE ALARM DEVICE NORMAL ALARM RETURN TO NORMAL

LN
ISA-A-4-5-6

VISUAL

AUDIBLE

AUTO RESET, LOCKING, NO FLASH

SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE RETURN TO NORMAL RETURN TO NORMAL BEFORE ACK

AO
ISA-A-5

VISUAL

AUDIBLE

AUTO RESET, NON LOCKING, NO FLASH

SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE RETURN TO NORMAL RETURN TO NORMAL BEFORE ACK

AONL
ISA-A-4-5

VISUAL

AUDIBLE

AUTO RESET, LOCKING

SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE RETURN TO NORMAL RETURN TO NORMAL. BEFORE ACK ACKNOWLEDGE

AF
ISA-A

VISUAL

AUDIBLE

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

97

AUTO RESET, NON-LOCKING

SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE RETURN TO NORMAL RETURN TO NORMAL. BEFORE ACK

AFNL
ISA-A-4

VISUAL

AUDIBLE

AUTO RESET, LOCKING, WITH FLASH RESET

SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE FLASH RESET RETURN TO NORMAL RETURN TO NORMAL. BEFORE ACK ACKNOWLEDGE FLASH RESET

FR

VISUAL

AUDIBLE

MANUAL RESET, LOCKING

SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE RETURN TO NORMAL RETURN TO NORMAL. BEFORE ACK ACKNOWLEDGE RESET

AM
ISA-M

VISUAL

AUDIBLE

MANUAL RESET, LOCKING, WITH FLASH RESET

SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE FLASH RESET RETURN TO NORMAL RETURN TO NORMAL. BEFORE ACK ACKNOWLEDGE FLASH RESET

FRM

VISUAL

AUDIBLE

98

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

FIRST OUT, FAST FLASH, LOCKING, AUTORESET

SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE RETURN TO NORMAL RETURN TO NORMAL BEFORE ACK. INITIAL NEXT ACKNOWLEDGE

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

AS
ISA-F1-A

VISUAL
FAST FAST

AUDIBLE

FIRST OUT, FAST FLASH, LOCKING, AUTORESET WITH SILENCE

SEQUENCE CODE ALARM DEVICE NORMAL ALARM SILENCE ACKNOWLEDGE RETURN TO NORMAL RETURN TO NORMAL BEFORE ACK. INITIAL NEXT ACKNOWLEDGE

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

ASFR
ISA-F1-A

VISUAL
FAST FAST FAST

AUDIBLE

FIRST OUT, FAST FLASH, LOCKING, FIRST OUT RESET WITH SILENCE
SEQUENCE CODE ALARM DEVICE NORMAL ALARM SILENCE ACKNOWLEDGE RETURN TO NORMAL RETURN TO NORMAL BEFORE ACK. INITIAL NEXT ACKNOWLEDGE RESET

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

RESET

ASFRM
ISA-F2M-1

VISUAL
FAST FAST FAST

AUDIBLE

FIRST OUT, TRIPLE FLASH, FIRST OUT RESET

SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE RETURN TO NORMAL RETURN TO NORMAL BEFORE ACK. INITIAL NEXT ACKNOWLEDGE FIRST OUT

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

RESET

TFS
ISA-F3A

VISUAL
SLOW INT. FAST FAST SLOW INT. FAST FAST SLOW

AUDIBLE

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

99

FIRST OUT, TRIPLE FLASH, FIRST OUT RESET, RESET

ACKNOWLEDGE SEQUENCE CODE ALARM DEVICE NORMAL ALARM SILENCE (FLASH RESET) INITIAL NEXT INITIAL NEXT INITIAL NEXT INITIAL NEXT INITIAL NEXT RESET FIRST OUT RESET RETURN TO NORMAL RESET

TFSFRM

VISUAL
INT. FAST FAST INT. FAST FAST SLOW

AUDIBLE

Note: The RESET and FIRST OUT RESET Pushbuttons are combined together at the same terminal.

FIRST OUT, TRIPLE FLASH, FIRST OUT RESET, RESET

SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE FIRST OUT RESET RETURN TO NORMAL RESET

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

RESET

TFSM

VISUAL
INT. FAST FAST SLOW

AUDIBLE

Note: The RESET and FIRST OUT RESET Pushbuttons are combined together at the same terminal.

RINGBACK, DUAL FLASH, LOCK IN UNTIL ACKNOWLEDGED

SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE RETURN TO NORMAL RESET

ARR
ISA-R

VISUAL
FAST SLOW

AUDIBLE

Ringback Audible

100

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

RINGBACK, DUAL FLASH, LOCK IN UNTIL ACKNOWLEDGED

SEQUENCE CODE ALARM DEVICE NORMAL ALARM SILENCE ACKNOWLEDGE (FLASH RESET) RETURN TO NORMAL RESET

FRR

VISUAL
FAST FAST SLOW

AUDIBLE

Ringback Audible

FIRST OUT, SINGLE FLASH DUAL COLOR WITH FIRST OUT RESET
SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE RETURN TO NORMAL FIRST OUT RESET FO RESET

INITIAL

NEXT

INITIAL

NEXT

INITIAL

NEXT

VS

VISUAL
LAMP 1 LAMP 2 LAMP 1 LAMP 2 LAMP 1 LAMP 2

AUDIBLE

Dual Lamp Sequences use only one input on each input card for a maximum of 2 alarms per window cell. Window Size 2 provides 1 alarm/cell, size 2S,2E & 4 provide 2 alarms/cell.

FIRST OUT, DUAL FLASH, DUAL COLOR, FIRST OUT RESET, RESET
SEQUENCE CODE ALARM DEVICE NORMAL ALARM ACKNOWLEDGE RETYURN TO NORMAL RESET FIRST OUT RESET NEXT FO RESET

INITIAL FAST

NEXT

INITIAL

NEXT

INITIAL SLOW

NEXT SLOW

INITIAL

FAST

VSRR

VISUAL
LAMP 1 LAMP 2 LAMP 1 LAMP 2 LAMP 1 LAMP 2 LAMP 1 LAMP 2

AUDIBLE

Ringback Audible

Dual Lamp Sequences use only one input on each input card for a maximum of 2 alarms per window cell. Window Size 2 provides 1 alarm/cell, size 2S,2E & 4 provide 2 alarms/cell.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

101

MOTOR CONTROL
SEQUENCE CODE ALARM DEVICE MOTOR ON ALARM ACKNOWLEDGE MOTOR RESTART MANUAL STOP

MC

VISUAL
FAST SLOW

AUDIBLE

Note: The Manual Stop function is provided through the Reset Pushbutton. It is a common control for the entire system and provides a manual stop indication (lamps and horn off) to all inputs in the alarm state.

For intermixed sequences specify IMO order code

LEGEND

LAMP OFF

LAMP FLASHING

LAMP ON

HORN OFF

HORN ON

102

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

APPENDIX B
MODBUS DATA FORMATS
The system has the capability of operating with three distinct data formats: fault mode, alarm state mode and AN3135 mode. The latter is designed to be compatible with existing AN-3100C Modbus installations. All these formats are embedded within Modbus data registers for transmission and reception. A selection of Modbus function may be used and these vary depending on the whether the SERIES 90A is operating as Modbus master or slave.
Data Direction Function Description Data Units Master Slave Input 3 Read Holding Registers Words Output Output 6 Preset Single Register Words Input Input 7 Read Exception Status Bytes Output Preset Multiple Output 16 Registers Words Input Input 17 Report Slave ID Bytes Output SERIES 90A Supported Mode Master or slave Slave only Slave only Master or slave Slave only

A function value of 03 (Read Holding Registers) is set to read alarm data from the system (in slave configuration). Function values 06 (Preset Single Register) and 16 (Preset Multiple Registers) are used to write fault and control data. Single and multiple register writes are supported. Exception status responses (function 07) and Slave ID (function 17) are also supported. Exception codes for unrecognized received messages are also included. The Modbus functions are enabled by a software switch and require a key to enable them, which is supplied by AMETEK. This may be done prior to delivery or retrofitted to installed systems.

Alarm State Mode

The system can provide data reflecting the alarm state of the system. This mode operates as output only (transmit alarms) from the system. The alarm state data is present within a 16 bit register format as shown in the table below. The data is in a nibble format (4 bits per point, 4 points per register) and reflects the already established DMS3000/RTU3000 style format. Note the control transfer is not supported in this mode as the control state of any point is included within the data transferred. Bit Point 1, First up, unacknowledged Point 1, Subsequent up, unacknowledged Point 1, Acknowledged Point 1, Fault

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

103

The data layout is as shown below.

Word 1 .. 60 Bit15-bit12 AP 04 .. AP 240 Bit11-bit8 .. .. .. Bit7-bit4 .. . .. Bit3-Bit0 AP 01 .. AP 237

Point Mode
The system can present or accept (transmit or receive) raw field input point data plus alarm controls. Single and multiple register writes are supported. Data is again presented in a 16 bit register format. The last word of a transfer of input data may optionally contain control data. The data layout for a sample system configured for point data will be as below.
Word 1 .. 15 16 Bit15 AP 16 .. AP 240 . . Bit6 .. .. .. Bit5 .. .. .. Bit4 .. .. .. Bit3 .. .. .. Ack Rec Bit2 .. .. .. Rst Rec Bit1 .. .. .. Ack Tran Bit0 AP 01 .. AP 225 Rst Tran

AP refers to Alarm Point Channel. ACK refers to the Acknowledge Pushbutton and RST refers to the RESET Pushbutton. The local pushbutton controls (on the front of the Annunciator and other ones connected to the external pushbutton inputs) can be transmitted (Tran) to a remote device using Ack Tran and Rst Tran as shown. The Annunciator can also receive (Rec) the pushbutton controls from the remote device using Ack Rec and Rst Rec as shown.

104

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

AN3135 Mode
The system has the capability of mimicking the existing AN-3100C Modbus functionality. The object is to provide a system that is backwards compatible with the existing AN-3135 Modbus Module used on AN-3100C systems. The AN3135 mode is restricted to the default Functions of 03 to read alarm data and 06 and 16 being used to write fault and control data. The principal difference between this and the point mode above is that the AN3135 mode is restricted to 64 points. The data layout for a sample system configured for point data will be as below.
Word
1 .. 4 5

Bit15
AP 16 .. AP 64

Bit6
.. .. ..

Bit5
.. .. ..

Bit4
.. .. ..

Bit3
.. .. .. Ack Rec

Bit2
.. .. .. Rst Rec

Bit1
.. .. .. Ack Tran

Bit0
AP 01 .. AP 49 Rst Tran

AP refers to Alarm Point Channel. ACK refers to the Acknowledge Pushbutton and RST refers to the RESET Pushbutton. The local pushbutton controls (on the front of the Annunciator and other ones connected to the external pushbutton inputs) can be transmitted (Tran) to a remote device using Ack Tran and Rst Tran as shown. The Annunciator can also receive (Rec) the pushbutton controls from the remote device using Ack Rec and Rst Rec as shown.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

105

Event Data
Event data may be read in blocks of 10 events at a time. These appear in a block of 60 registers (6 per event) located at the configured Start Address plus 1000 i.e. if the Start Address is set to 40001 then the events appear at 41001-41060. Once ten events are read then the registers are reloaded with any subsequent ones from the 500 event buffer. If no event has occurred, then all 12 bytes are filled with FF HEX. The event data format is as shown below:
Word 1 2 3 4 5 6 MSB Year Day Minute Millisecond (0-999) 0x00 IRIG-B Sync LSB Month Hour Second Input Point No. 1 = Point on 0 = Point off

An example of the register format for the 10 events is shown below:

Event Data 41001 1st Event 41002 41003 41004 41005 41006 41007 2nd Event 41008 41009 41010 41011 41012 Year (0-99) high byte / Month (1-12)low byte Day of month (1-31)high byte /Hours (0-23) low byte Minutes (0-59) high byte / Seconds (0-59) low byte Milliseconds (0-999) two bytes SERIES 90A Point Number (1-198) IRIG-B Sync high byte / Point Status (1 = A, 0 = N) low byte Year (0-99) high byte / Month (1-12)low byte Day of month (1-31)high byte /Hours (0-23) low byte Minutes (0-59) high byte / Seconds (0-59) low byte Milliseconds (0-999) two bytes SERIES 90A Point Number (1-198) IRIG-B Sync high byte / Point Status (1 = A, 0 = N) low byte

41054 41056 41057 41058 41059 41060

10th Event

Year (0-99) high byte / Month (1-12)low byte Day of month (1-31)high byte /Hours (0-23) low byte Minutes (0-59) high byte / Seconds (0-59) low byte Milliseconds (0-999) two bytes SERIES 90A Point Number (1-198) IRIG-B Sync high byte / Point Status (1 = A, 0 = N) low byte

* Supports Master or Slave Mode, Transmit only

106

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

Modbus Addresses
Conventional addresses are included in the configuration. The input and output functions here are the most commonly used and refer to a system in slave configuration.
Conventional Start address 00000 10000 30000 40000* 60000 Data Output Coils Discrete Inputs Input Registers Holding (output) Registers Extended Memory Input Functions 05,15 Output Functions 01 02 04 03

06,16

*Supported in the SERIES 90A

Default Values
Designation Modbus Address Receive Start Address Transmit Start Address Modbus Mode Data type Baud rate Parity Transmit controls Data direction Modbus format Options 0-255 40001-49999 40001-49999 Master/Slave AN3135 /Point/State 2400/4800/ 9600/19200 Odd/Even/none Yes/No Input/output ASCII/RTU Default 01 40001 40001 Slave Point 9600 None Output RTU Parity type Send alarm control (ACK, RST) data 1 bit per point to designate Tx/Rx data Comments Register address entry.

An3135 mimic, point or alarm state data.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

107

APPENDIX C
DNP DATA FORMATS
The DNP Communication option is used to transmit point status (Binary Inputs) to other devices. When the SER time-stamped alarms option is enabled, a historical record of binary input change events and the time at which they occurred can also be sent. The DNP Communications work in a slave mode and operate over RS-232/485 or Ethernet. The DNP implementation is outlined in the Device Profile Document.

DEVICE PROFILE DOCUMENT

DNP V3.0
DEVICE PROFILE DOCUMENT
Vendor Name: AMETEK Power Instruments Device Name: AN3100D, using the Triangle MicroWorks, Inc. DNP3 Multi-Port Slave Source Code Library Highest DNP Level Supported: Device Function: For Requests: Level 2 Slave For Responses: Level 2 Notable objects, functions, and/or qualifiers supported in addition to the Highest DNP Levels Supported (the complete list is described in the attached table): For static (non-change-event) object requests, request qualifier codes 00 and 01 (start-stop), and 17 and 28 (index) are supported in addition to request qualifier code 06 (no range or all points). Static object requests received with qualifiers 00, 01 or 06, will be responded to with qualifiers 00 or 01. Static object requests received with qualifiers 17 or 28 will be responded to with qualifiers 17 or 28. For change-event object requests, qualifier codes 06 (no range) and 07 and 08 (limited quantity) are supported. Qualifiers 17 or 28 are always returned. Maximum Data Link Frame Size (octets): Transmitted: 292 Received 292 Maximum Data Link Re-tries: Configurable from 0 to 255 Maximum Application Fragment Size (octets): Transmitted: 170 Received 50 Maximum Application Layer Re-tries: None

Requires Data Link Layer Confirmation: Configurable as: Never, Only for multi-frame messages, or Always Requires Application Layer Confirmation: When sending multi-fragment responses (Slave devices only) Sometimes

108

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

DNP V3.0
DEVICE PROFILE DOCUMENT
Timeouts while waiting for: Data Link Confirm: Configurable. Complete Appl. Fragment: None Application Confirm: Configurable. Complete Appl. Response: None Others: Transmission Delay, configurable Inter-character Timeout, 1 second Need Time Delay, configurable

Frozen Counter Change Event Scan Period, Fixed at 1 second

Sends/Executes Control Operations: WRITE Binary Outputs SELECT/OPERATE DIRECT OPERATE DIRECT OPERATE NO ACK Count > 1 Pulse On Pulse Off Latch On Latch Off Queue Clear Queue

Never Never Never Never Never Never Never Never Never Never Never Reports time-tagged Binary Input Change Events when no specific variation requested: Never Sends Static Data in Unsolicited Responses: Never No other options are permitted. Counters Roll Over at: No Counters Reported

Reports Binary Input Change Events when no specific variation requested: Never Sends Unsolicited Responses: Never Default Counter Object/Variation: Default Object 1 Default Variation: 1

Yes

IMPLEMENTATION TABLE
OBJECT
Object Numbe r 1 Variation Number 1 Description

REQUEST
Function Codes (decimal) 1 (read)

RESPONSE
Function Codes (decimal) 129 (response) Qualifier Codes (hex) 00, 01 (startstop)

Binary Input

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

109

PUSHBUTTON CONTROLS
Pushbutton activation can be transmitted from the Annunciator via a Binary input to indicate whenever a pushbutton is activated locally at the Annunciator. (Reference the Binary Input Data Map for location of the pushbutton indications.) Pushbutton controls can be sent to the Annunciator using a Control Relay Output block, as detailed below. Control Relay Output Block (Object 12, variation 2) DNP Object Index #
00 Object Numbe r 10 Variation Number 02

Description Control Code

LON, Reset Pushbutton LOFF * LON, 01 10 02 Acknowledge Pushbutton LOFF * For proper pushbutton operation, transmit a single LON (latch on) followed by a single LOFF (latch off). Allow a few seconds in between commands to ensure the Annunciator receives the pushbutton controls. Mode: Direct 16 Bit Index The Pushbutton Control Status can be checked by issuing a Binary Output Status, Object 10, variation 2. Binary Output Status (Object 10, Variation 2) DNP Object Index #
00 01 Object Number 10 10 Variation Number 02 02

Description
Reset Pushbutton Acknowledge Pushbutton

110

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

SERIES 90A DATA MAP

Binary Inputs
The Annunciator alarms are presented as binary inputs as shown below. DNP Object Index #
00 01 02 03 04 05 06 07 08 09 10 Object Number 01 01 01 01 01 01 01 01 01 01 01 Variation Number 00 00 00 00 00 00 00 00 00 00 00

Description
Point 1 Digital Contact Alarm Point 2 Digital Contact Alarm Point 3 Digital Contact Alarm Point 4 Digital Contact Alarm Point 5 Digital Contact Alarm Point 6 Digital Contact Alarm Point 7 Digital Contact Alarm Point 8 Digital Contact Alarm Point 9 Digital Contact Alarm Point 10 Digital Contact Alarm Point 11 Digital Contact Alarm

196 197 198 199 200 201

01 01 01 01 01 01

00 00 00 00 00 00

Point 197 Digital Contact Alarm Point 198 Digital Contact Alarm Point 199 Digital Contact Alarm Point 200 Digital Contact Alarm Acknowledge Pushbutton Reset Pushbutton

Binary Input Change with Time (SER Option)

The time stamped alarms are presented as Binary Input Changes with Time when the SER Option is provided.
DNP Object
Object Number 02 Variation Number 02

Description
Digital Contact Alarm w/time of event

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

111

APPENDIX D
WINDOW ASSEMBLY DETAILS
The Annunciator uses a common window assembly for all window configurations. The different window options are created using dividers (for the 4 window sizes) and colored filters for the different window colors (white, red, blue, green, amber, yellow). The assembly drawings on the next page identify the different options available. A typical window consists of the following parts: Transparency film with Legends Colored Filter if required (red, blue, green, amber, yellow) White Diffusers (to eliminate LED hotspots)

All of these parts are pressed into the clear window, which is inserted into the window frame.

Window Legends
The Annunciator Window Legends are typically printed on clear transparency film, which is provided with the Annunciator. There is an option to engrave these legends directly on the window (Option E). For printing of legends on the transparency film, the Software CD will include a template in Microsoft Excel. You type the legend in the window template that matches your size window and print on a suitable printer. (A laser printer is recommended or any type that is compatible with printing on Transparency film.)

Window Colors
The Annunciator Window Colors are provided through colored filters, which are provided with the Annunciator. In cases where several different window colors are required for an individual Cell (option IMC), the laser printed transparency will be colored in place of the color filters. In these cases, color Laser Printer should be used. Note: All legends and pre-printed colors will be provided with the Annunciator if the details are provided before the unit ships.

112

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

TWO WHITE DIFFUSERS, ONE COLOR DIFFUSER, ONE CLEAR LEGEND TWO WHITE DIFFUSERS. ONE CLEAR LEGEND
TOUCHPAD TWO DIVIDERS USED TO SUPPORT TOUCHPAD SUPPORT

TWO WHITE DIFFUSERS, (ONE COLOR DIFFUSER OPTIONAL)

MEMBRANE TOUCHPAD

ENGRAVED LEGEND

FIGURE 1B FIGURE 1 A PRINTED LEGEND (WHITE WINDOW) CONFIGURATION

8
11

FIGURE 2 CELL MEMBRANE TOUCHPAD CONFIGURATION

FIGURE 3

PRINTED LEGEND (COLOR) CONFIGURATION

ENGRAVED LEGEND CONFIGURATON

10 SEE NOTE 1

12

SEE NOTE 2 AND FIGURE 1A, 1B & 3 USED WITH WINDOWS

16

ASSEMBLY PART IDENTIFICATION

13

SEE NOTE 2 AND FIGURE 2 USED WITH TOUCHPAD

INDEXPART NUMBER
8 9 10 11 1085-252 1085-394 1085-400 1085-396 12 1085-397 13 14 16 1085-398 1085-399 1085-389

DESCRIPTION

DISPLAY (LED) PCB

HOUSING, FRONT MODULE

DIVIDER, CELL WINDOW

DIFFUSER, WINDOW INSERT

Window Assembly

9 10 SEE NOTE 1 THIS VIEW SHOWN WITH ALL PARTS FOR ANY CONFIGURATION.

LEGEND, WINDOW INSERT

WINDOW, MOLDED

WINDOW FRAME

PLATE, MEMBRANE SWITCH INSERT

NOTES: 1. DIVIDER QUANTITY AND LOCATION IS DEPENDANT ON CELL ALARM CONFIGURATION. 2. SEE FIGURES 1, 2, AND 3 FOR WINDOW CONFIGURATIONS. FIG 1A: THESE THREE ITEMS ARE USED TOGETHER FOR THE PRINTED LEGEND WITH WHITE WINDOWS
14

FIG 1B: THESE FOUR ITEMS ARE USED TOGETHER FOR THE PRINTED LEGEND FOR COLORED WINDOWS FIG 2: THIS ITEM IS USED WITH A CELL MEMBRANE TOUCHPAD OPTION. FIG 3: THIS ITEM IS USED FOR THE ENGRAVED LEGEND OPTION.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

113

APPENDIX E
TELEPHONE / FAX NUMBER LIST
This errata sheet provides an easy-to-use reference for all major departments. Use these numbers for ordering equipment, application assistance, technical support, and scheduling field service Please Note: Your instruction manual may contain other phone and fax numbers; this list will take precedence. MAIN OFFICE AMETEK Power Instruments Rochester 255 North Union St., Rochester, NY 14605
DEPARTMENT/PRODUCT LINE MAIN PHONE FIELD SERVICE REPAIRS/RETURNS SALES SUPPORT TELEPHONE 585-263-7700 800-374-4835 888-222-6282 800-950-5503 FAX 585-262-4777 585-238-4945 585-238-4945 585-454-7805

FAR EAST OFFICE

AMETEK Power Instruments 271 Bukit Timah Road, #03-09 Balmoral Plaza, Singapore 259708 Tel: 65-732-8675 Fax: 65-732-8676

UK OFFICE
AMETEK Power Instruments Unit 20, Ridgeway Donibristle Industrial Estate Dunfermline, UK Tel: 1383-825630 Fax: 1383-825715

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

115

PROCEDURES FOR FACTORY REPAIR AND RETURN

B. Obtain a Returned material Authorization (RMA) number by calling AMETEK Repair Sales and giving the following information:
Model and Serial Number of the equipment Failure Symptom Be Specific Approximate date of installation The site name and address of the failed equipment Complete shipping information for the return of the equipment if other than the operating site

Name and telephone number of person to contact if questions arise. Enclose the information with the equipment and pack in a commercially accepted shipping container with sufficient packing material to insure that no shipping damage will occur. Mark the outside of the container with the RMA number. Ship to the appropriate location
Attention: Repair Department AMETEK Power Instruments 255 North Union Street Rochester, New York 14605 USA Tel: (888) 222-6282 Fax: (585) 238-4945

Your emergency equipment will be tested, repaired and inspected at the factory. Factory turnaround is ten working days or less (excluding shipping time). For emergency service or repair status information, please contact the AMETEK Repair Sales Engineer at (800) 374-4835.

WARRANTY
AMETEK warrants equipment of its own manufacture to be free from defects in material and workmanship, under normal conditions of use and service. AMETEK will replace any component found to be defective, upon its return, transportation charges prepaid, within one year of its original purchase. AMETEK will extend the same warranty protection on accessories that is extended to AMETEK by the original manufacturer. AMETEK assumes no responsibility, expressed or implied, beyond its obligation to replace any component involved. Such warranty is in lieu of all other warranties expressed or implied.

SERIES 90A ANNUNCIATOR INSTALLATION AND CONFIGURATION MANUAL

117