Scribd
Upload
443 views

Fixed Cutter - IADC Dull Grading

Halliburton's Fixed Cutter bits are tip ground to exacting tolerances at gauge O.D. Per API spec 7. Depending on the specific design and application as much as.080 of an inch of the cutter diameter may be ground flat. This can be mistaken for gauge wear if unfamiliar with our products.

Uploaded by

César González Cruz
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
443 views

Fixed Cutter - IADC Dull Grading

Halliburton's Fixed Cutter bits are tip ground to exacting tolerances at gauge O.D. Per API spec 7. Depending on the specific design and application as much as.080 of an inch of the cutter diameter may be ground flat. This can be mistaken for gauge wear if unfamiliar with our products.

Uploaded by

César González Cruz
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DriLL Bits

Fixed Cutter

IADC Dull Grading


Cutting Structure
Inner Rows
1

Outer Rows
2

Dull Char.
3

Location
4

Bearings/Seals X

Gauge
6

Other Dull Char.


7

Reason Pulled
8

Inner Area 2/3 Radius

Outer Area 1/3 Radius

1 2

Inner Cutting Structure Outer Cutting Structure

Location X All Areas Cone Gauge Nose Shoulder Taper

HAL9086

A measure of lost, worn and/or broken cutting structure. Linear Scale: 0-8 0 8
3

- No lost, worn and/or broken cutting structure - All of cutting structure lost, worn and/or broken Dull Characteristics Bond Failure Broken Cutters Balled Up Cored Chipped Cutters Delaminated Cutters Erosion Heat Checking Junk Damage Lost Matrix Lost Nozzle Lost Cutters No Dull Characteristics Not Rerunnable Plugged Nozzle/Flow Passage Ring Out Rerunnable Washed Out Worn Cutters

A C G N S T
5

Gauge Shoulder
HAL9085

Taper Nose

Cone

No Wear

Worn Cutter

Halliburton's fixed cutter bits are tip ground to exacting tolerances at gauge O.D. per API spec 7. Depending on the specific design and application as much as .080 of an inch of the cutter diameter may be ground flat. This can be mistaken for gauge wear if unfamiliar with our products. Please ensure that dull bits are in gauge with a calibrated PDC No Go ring gauge.

HAL9045

Lost Cutter

Delaminated

BF BT BU CR CT DL ER HC JD LM LN LT NO NR PN RO RR WO WT

6 Gauge (Measure in fractions of an inch) I - In Gauge 1 - 1/16" Out of Gauge 2 - 1/8" Out of Gauge 4 - 1/4" Out of Gauge 7

Other Dull Characteristics

(Refer to column 3 codes)


8

Reason Pulled or Run Terminated Change Bottomhole Assembly Condition Mud Core Point Downhole Motor Failure Drill Plug Drill String Failure Drill Stem Test Downhole Tool Failure Formation Change Hole Problems Hours on Bit Left in Hole Run Logs Pump Pressure Penetration Rate Rig Repair Total Depth/Casing Depth Torque Twist Off Weather Conditions Washout - Drill String

BHA CM CP DMF DP DSF DST DTF FM HP HR LIH LOG PP PR RIG TD TQ TW WC WO

HAL9045

DriLL Bits

FIXED CUTTER BITS - RING GAUGING

Any fixed cutter bit should be ring gauged prior to running in the hole. Stabilizers should also be calipered or gauged to verify they meet API-approved outside dimension tolerances as shown in the following table. Fixed cutter bits should not be larger than the nominal diameter. API Fixed Cutter Bit Tolerances
BIT SIZE (IN.) 6-3/4 and Smaller 6-25/32 to 9 9-1/32 to 13-3/4 13-25/32 to 17-1/2 17-17/32 and Larger FIXED CUTTER BIT O.D. TOLERANCE (IN.) -0.015 to +0.00 -0.020 to +0.00 -0.030 to +0.00 -0.045 to +0.00 -0.063 to +0.00

A no go gauge is used to ensure a bit is not smaller than allowed and, as the name implies, it should not go or slip down the entire length of the bit. A go gauge ensures a bit is not larger than allowed and should slip down the entire bit.

2009 Halliburton. All rights reserved. Sales of Halliburton products and services will be in accord solely with the terms and conditions contained in the contract between Halliburton and the customer that is applicable to the sale. H03086 9/09 www.halliburton.com

You might also like