Scribd
Upload
440 views

Cablemaster CM - Remote Control Programing Guide

This document provides instructions for programming a remote control module and wiring diagram for connecting the remote control to a Cablemaster system. The programming instructions are: 1) Push the program switch until the LED lights, 2) Push the transmitter button until the LED goes out, 3) Push the transmitter button again until the LED flashes slowly, then release, 4) The remote is now programmed and can be tested, noting that repeating steps 1-4 programs a second transmitter. The wiring diagram shows how to connect the remote control, relay assembly, motor, battery and limit switches for one or two Cablemaster units.

Uploaded by

Glendinning Products, LLC.
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
440 views

Cablemaster CM - Remote Control Programing Guide

This document provides instructions for programming a remote control module and wiring diagram for connecting the remote control to a Cablemaster system. The programming instructions are: 1) Push the program switch until the LED lights, 2) Push the transmitter button until the LED goes out, 3) Push the transmitter button again until the LED flashes slowly, then release, 4) The remote is now programmed and can be tested, noting that repeating steps 1-4 programs a second transmitter. The wiring diagram shows how to connect the remote control, relay assembly, motor, battery and limit switches for one or two Cablemaster units.

Uploaded by

Glendinning Products, LLC.
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

REMOTE CONTROL PROGRAMMING

Locate the program switch under the access panel on the front of the Remote Control module as shown below (Fig. 1).

Remove access panel

Fig. 2

Program Switch (SW1)

Program LED

Transmitter LED

Fig. 1

Button 1

Fig. 3

Read through the steps below BEFORE you begin. You will have 10 seconds to complete the programming sequence.

1. Push the program switch (SW1) (Fig. 2) until the red program LED lights solid, then release switch. 2. Push button 1 on the remote transmitter until the program LED goes out (Fig. 3). 3. Push button 1 on the transmitter again, the program LED should flash slowly ... now release button. 4. Remote is now programmed. Test unit. NOTE: If the remote does not work, make sure that the transmitter LED is flashing when button 1 is pressed, and that the battery is good. Repeat steps 1-4. 5. Repeat steps 1-4 for second transmitter.
CMRCP_v3.0

CABLEMASTER REMOTE CONTROL WIRING DIAG


WHITE

OUT

UNIT - #1 (Channels 1 & 2)

RED BLACK

OFF IN

(see note -1)

BATERY POSITIVE (+)

CABLEMASTER RELAY ASSEMBLY # 04034 - (12, 24 volt DC) 12/24 Power DC Input Switch RED Pos. + Red 1
(Remote - RED) (Remote - BLACK)

POWER SWITCH
(Remote - Red) (Remote - Yellow) (Remote - Green)

BATTERY NEGATIVE (-)


(Remote - Black)

Neg. -

(Rmt - Yellow or Purple)

White 2 Black 3

WHITE BLACK

(Rmt - Green or Tan)

Motor Output Orange Black

IN 4 Limit Switch 5 OUT 6 Limit Switch 7

M
(see note -2)

ORANGE BLACK

IN-LIMIT SWITCH OUT-LIMIT SWITCH


NOTE: With the new relay assembly a 12VDC Remote Control is required to be used for all voltages (12 or 24 VDC)
(Remote - Black)

12v DC use 20 amp breaker 24v DC use 15 amp breaker

12 or 24vdc MOTOR

GLENDINNING MARINE PRODUCTS, INC. Conway, SC 843-399-6146

(if operating 2 Cablemasters)


WHITE

UNIT - #2 (Channels 3 & 4)


CABLEMASTER RELAY ASSEMBLY # 04034 (12, 24 volt DC) 12/24 Power DC Input Switch RED Pos. + Red 1
(Remote - RED) (Remote - BLACK)

OUT OFF IN

RED BLACK

BATERY POSITIVE (+)


(see note - 1)

(Rmt - Yellow or Purple)

(Rmt - Green or Tan)

Motor Output

IN 4 Limit Switch 5 OUT 6 Limit Switch 7

12 VDC

Black 3

BLACK

(Remote - Tan)

( -- ) (+)

BATTERY NEGATIVE (-)

Neg. -

White 2

WHITE

(Remote - Purple)

M
12,24 v MOTOR
(see note - 2)

ORANGE BLACK

Orange Black

IN-LIMIT SWITCH OUT-LIMIT SWITCH

12v DC use 20 amp breaker 24v DC use 15 amp breaker GLENDINNING MARINE PRODUCTS, INC. Conway, SC 843-399-6146

Note: 1.) Connect battery positive lead via fuse or circuit breaker. See Installation Manual for rating. Circuit Breaker Specs.: CM7 - 12 Volt 20 Amp Breaker 8-10 Running Amps CM7 - 24 Volt 15 Amp Breaker 5-6 Running Amps 2.) For low profile Cablemaster installation, the motor leads must be reversed for correct limit switch operation. See manual for more information.
95405_Remote_Wire.cad

IN

REMOTE KEY PAD

REMOTE CONTROL

POWER SWITCH

OUT
Channel #2 Channel #4

Channel #1 Channel #3

Version - T41304 / 2

You might also like